Search Documents

By H. T. Lundberg, J. H. Ratcliffe

In airborne gravity surveys effects of acceleration and irregular movements of the aircraft must be balanced out or overcome. The gradient of vertical gravity is recorded, therefore, by using two masses instead of one. As the amplitude variations are infinitesimal and difficult to measure accurately, at present it is enough to determine whether variation of gradient during flight is positive or negative. The positive portions of the pattern can then be indicated and contoured. Even with these simplifications, the source of energy must be exceptionally stable. General Principles: In the conventional gravi-meter the weight of a standard mass is determined at a number of selected points within the survey area. In most systems weight is determined by comparing the gravity pull with extension or torque

Jan 1, 1960

By Lawrence Burkhart, S. B. Joo

A hemispherical, constant volume drop with forced internal circulation was considered as a model approximating a real drop at a similar stage of formation Axially symmetric steady flow within a drop contaminated by surfactants was described by solving the full Navier-Stokes equations written in terms of a meridian plane stream function Rotational flow occurred inside the drop above a computed Reynolds number of 5.8, and the change in interfacial flow caused by imposing a surface-tension gradient at the surface had a significant effect on the internal flow Although the work is quite fundamental in nature, the rotational flow described in the paper is responsible for much of the bulk transport of solute to the interface in hydrometallurgical processes such as solvent extraction.

Jan 1, 1981

By J. K. Gerlach, E. D. Gock, S. K. Ghosh

Previous experience in leaching chalcopyrite with dilute sulfuric acid has generally resulted in rather poor extraction. However, the reaction rate of the leaching process can be significantly improved by an increase of the crystal lattice defects of the chalcopyrite. It was found that subjecting chalcopyrite to a milling action involving a strong impact, permits 99 percent of the copper to be extracted in a subsequent single leaching stage with at least stoichiometric quantities of sulfuric acid in the presence of oxygen at 100°C. Simultaneously, about 80 to 85 percent of the sulfide sulfur content is converted to elemental sulfur. The dependence of the reaction rate of chalcopyrite on the pretreatment, temperature, oxygen pressure and acid content will be discussed.

Jan 1, 1973

By H. William Ahrenholz

Many technical meetings were attended by mining people during the past year in which rock mechanics was either the main subject for discussion or was a prominent part of the program. Several universities continued to offer short courses in the applications of rock mechanics for practicing mining engineers. At the beginning of the year, the AIME Committee on Rock Mechanics achieved standing-committee status. It is to assume responsibility for coordinating all AIME activities in this area. Eleven professional societies are now participating in a newly formed Intersociety Committee for Rock Mechanics. AIME and its constituent societies has three representatives. Delegates from the Intersociety Committee will serve on the U.S. National Committee for Rock Mechanics which is being formed by the national Academy of Sciences.

Jan 2, 1967

By Helen L. Cannon

BOTANICAL methods of prospecting for metalliferous ores are based on the premise that deposits at depth may be reflected chemically in surface vegetation. For the past several years, on behalf of the Atomic Energy Commission, the U. S. Geological Survey has investigated on the Colorado Plateau the application of botanical methods to uranium prospecting. Results suggest that orebodies may be found under a considerable cover of barren sandstone through the absorption of uranium and associated trace elements by plants growing at the ground surface. Plant physiologists have demonstrated that uranium is a necessary nutrient for plant growth and therefore is present in all plants.' The amount present is small but measurable. The absorption of uranium by plants growing over ore deposits forms

Jan 1, 1955

By J. Weng

The equations of heat conduction are numerically solved for two kinds of artificial freezing- mechanical freezing and liquid nitrogen freezing. A two dimensional finite difference model simulating the freezing field is developed. The procedure introduces a way to simulate the effect of latent heat released when water transforms from liquid to solid. The procedure also produces a way to calculate the harmonic mean of heat conductivity used when dealing with heterogeneous material. The theoretically derived temperature distributions in frozen soil are given and compared with measured data. An analysis made on the thermal design in shaft freezing. The average temperature of frozen soil is calculated by using numerical integration. The regularity of development of frozen soil radius is revealed and given in an appropriate mathematical model.

Jan 1, 1984

By Olin G. Bell

During the year 1928 ten new producing areas have been discovered and several extensions in oil and gas fields have been found in southwestern Texas. This year, however, will reveal itself as one of small profits in spite of considerable increase in production for the area as a whole over the previous years. At the beginning of 1928 the fields in this area (Fig. 1) were producing a daily average of 7500 bbl. from 730 wells, whereas at the close of the year the daily average had increased to approximately 14,000 bbl. from 827 wells. Production for the year was 3,453,938 bbl. The total oil produced in Southwest Texas since its discovery has been 16,955,-388 barrels. (Table 1.)

Jan 1, 1929

By R. J. Jones, L. D. Clark, R. C. Howell

This research provides an empirical approach toward further analysist10 of the variables in rock breakage under direct, hydroimpact (impacting on fluid) and explosive impulse loading. That the strain on the face of a block of rock, below an impact pin or explosive charge, is directly proportionate to the rupturing force F and inversely proportionate to the product of the burden W and the hole periphery S, is borne out in the laboratory using electrical resistance strain gages to measure a peak strain during rupture by small explosive charges detonated in boreholes. Furthermore, such findings established the validity of the expression F = Ss • Wy • R as a useful relationship from which, it is believed, can be derived practical applications in commercial rock blast design.

Jan 1, 1972

By Kenneth Robertson

THEREi9 probably less known of this subject than of any other connected with the metallurgy of iron. In all the books that treat of this mattes, there are given analyses of slags, their chemical formulae, the loss of iron, etc. ; but few, if any, give the character of the iron made at the time ; none give analyses and physical characteristics of the ores and limestones used, and they present merely isolated examples from various furnaces, and consequently one is more frequently puzzled than enlightened after reading them. During two years I have had occasion to analyze the slags and many of the pig-irons from two furnaces, and for this article I have made analyses of all the different grades of pig made by them. A

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid- fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made.1 Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system.

Jan 12, 1954

By Rodney Lawrence, Tim Hackett

INTRODUCTION The western USA contains significant coal reserves in seams 10 feet or more in thickness which lie too deep for surface mining. As part of a demonstration of the use of two legged shield supports in the United States, Kaiser Steel Corporation, under contract to the US government used the longwall method to mine a ten foot thick coal seam in New Mexico. Caliper type shield supports and double drum shearers were used in three longwall panels. During the test, technical, production, and safety data were collected to objectively evaluate the performance of the shields in mining the thick coal seam. This paper presents discussions of practical operating experience and summary statistics to aid the mining industry in planning longwall mines in similar conditions.

Jan 1, 1981

By W. H. Holman, J. B. Wagstaff

IN spite of considerable interest among blast furnace operators on the question of the penetration of air into the furnace, there is still uncertainty as to how far the blast does, in fact, penetrate. Moreover, it is not always clear just what is meant by the word penetration in this sense. In 1952, Elliott et al.1 showed that at the end of each tuyere of a blast furnace there is more or less of a void. In this region, coke particles are blown around by the force of the air. This explained the well-known observation reported by Sweetser2 hat if a bar is pushed into a furnace through a tuyere it will go easily into the furnace a distance of some

Jan 1, 1958

By Peter Joralemon

Peter Joralemon's contention that Nevada contains one of the world's major gold belts is the result of 30 years' active involvement with the state's regional geology. He first suggested the possibility of an arsenical gold belt-tenuously based on two replacement deposits 480 km (300 miles) apart-in his 1949 doctoral thesis of the Getchell mine. In the years that followed, some 18 or 20 arsenical gold ore bodies have been discovered along the lineament Joralemon postulated. In this article, he uses the evidence that he's collected over the last three decades to refine his 1949 thesis. Joralemon's conclusion: A mineral belt containing a billion dollars worth of gold extends the length of Nevada, and a number of ore bodies are yet to be discovered.

Jan 7, 1978

The new saw mill at Cache Bay of the Geo. Gordon & Co., Ltd., a subsidiary of International Nickel Co., of Canada, is equipped with the first fully electric saw carriage drives in Ontario. It has a capacity of 120,000 ft of lumber in an 8-hr shift. About half of the mill's production is high grade white pine lumber which is shipped to the general market. The other half, red pine is used in the mining operations of International Nickel in the Sudbury district, 55 miles west of Cache Bay. [ ] Inco with a potential need of 77 million board ft a year, gets only part of its supply from the new mill. The milling firm became an Inco subsidiary Jan. 1, 1948.

Jan 1, 1952

During the last 15 years, the bucket wheel has become increasingly popular as a mining tool. Being a large-capacity continuous mining excavator, the machine offers low actual operating costs and low unit costs. Of German origin, the bucket wheel has now appeared on the American mining scene as well as in such other places as Australia, Northern Rhodesia, South Africa, Congo, Indonesia, and India. Patented in 1913, the first practical application waited until 1920 when a bucket wheel excavator was placed in operation at an open pit lignite mine in central Germany. This initial experiment met with little success due to difficulties in solving the technical problems of the machine's construction rather than to the design of the wheel itself.

Jan 9, 1960

By Allan T. Fisk, Carl R. Peterson, Richard E. Brooks, James J. Olson

Development of a continuous drill-and-blast excavation capability in mining and high-speed tunneling has been a long recognized goal. Ideally, a machine to meet the challenge should simultaneously perform drilling, explosive loading, initiation, mucking, ventilation, and other functions while remaining at the face, since the elimination or modification of the cyclic nature of the system would significantly improve the advance rate and economy of drill-and-blast tunneling. The Rapidex continuous spiral drill-and-blast concept, one of the continuous excavation schemes presently under evaluation in the US Bureau of Mines' Bedded Deposits subprogram, utilizes an unusual blasting pattern that provides effective fragmentation and involves a partially self-shielding geometry that permits a lightly shielded machine to remain at the face during blasting.

Jan 6, 1977

By Kenneth Robertson

THERE is probably less known of this subject than of any other connected with the metallurgy of iron. In all the books that treat of this matter, there ore given analyses of slags, their chemical formulae, the loss of iron, etc. ; but few, if any, give the character of the iron mode at the time; none give analyses and physical characteristics of the ores and limestones used, and they present merely isolated examples from various furnaces, and consequently one is more frequently puzzled than enlightened after reading them. During two years I have had occasion to analyze the slags and many of the pig-irons from two furnaces, and for this article I hove made analyses of all the different grades of pig mode by them. A

Jan 1, 1873

By G. M. Ritcey

Purification of solutions can involve various treatment methods. In the normal sequence of metals recovery by hydrometallurgy, the ore is initially prepared for leaching by grinding to the desired optimum mesh size as dictated by the leaching parameters. Following leaching and liquids- solids separation, the resultant solution is ready for purification. The use, or introduction of solvent extraction into a plant, can be either a major or a minor part of the metal recovery process as shown by the following list where solvent extraction is normally considered: a) recovery of a metal by a simple leaching of the broken ore, e.g., copper from dump leaching where there are only the three main steps of leaching, solvent extraction, and electrowinning (1);

Jan 1, 1978

By F. W. McQuiston

Teamwork is the key to an efficient organization. Cooperation among mining staff members is an obligation owed to the company. The more cooperation the metallurgist receives from underground, the higher milling yield will be, which in turn makes for a greater mine profit. There is no pay for metal left in mill tailings. The metallurgist is not in a position to be of help to either the geologist or mining engineer, but can receive valuable assistance from both. Therefore, the metallurgist must win underground cooperation. The mining engineer is usually interested in geology because of its relation to ore control; in milling because that is where the rock goes. However, any overlapping of interest between geologist and metallurgist is quite remote.

Jul 1, 1956

By William P. Blake

(Canal Zone Meeting, November, 1910.) A DEPOSIT of manganese-ore near Tucson, Ariz., merits notice by reason of the peculiar form in which it occurs, and as a striking. example of ore-deposition by vadose upward capillary flow of metal-bearing solutions with concentration at the surface of the country-rock. This deposit occurs at the northern end of the Coyote mountains, about 40 miles west of Tucson, upon the outcropping beds of porphyritic rock, which appear to be partly-metamorphosed strata of volcanic tufa, probably of late Secondary or of Tertiary age. The strata dip northward at a low angle, and present a series of basset-edges in parallel lines of outcrop, east and west, facing the south and extending over many acres. Successive groups of these outcrops, from 5 to 20 ft. in breadth, are coated with oxides of manganese in lustrous black films and crusts, shining in the sunlight like polished ebony, and covering the whole surface of the rock above the soil. Seen at a little distance, these croppings look like solid ledges of massive and pure ore; but closer inspection and a few blows of the hammer reveal their true nature as a superficial coating allied in origin to the blackened shining surface of rocks exposed in desert-regions, familiarly known as " desert paint" or "desert varnish,"' similar to the phenomena described by me in a former paper, but much thicker and heavier. * By reason of the death of the distinguished author, this communication, probably his last communication to technical literature, is published without revision of the proofs by him. A term first given y G. K. Gilbert. See Rocks, Rock-Weathering, and Soil; by George P. Merrill, p. 256 (New York, 1897). Superficial Blackening and Discoloration of Rocks, Especially in Desert Regions, Trans., xxxv., 371 (1905).

Sep 1, 1910