Search Documents

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

The temperature, orientation, and strain-rate dependence of tensile flow in single-crystal NiA1 of equiatomic composition have been investigated up to 800°C. Compression tests at room temperature have also been carried out. Optical and replica electron microscopy and X-ray diffraction methods were used to investigate the slip mechanisms. NiAl exhibits {110)(001) slip and cube slip {l00)(010) was also observed. This results in very high strength of single crystals in cube orientation. The implications of this slip mode, with the resultant small number of possible slip systems and three mutually perpendicular slip vectors, are discussed. ThE CsCl structure compounds represent a class related to the bcc elements, but their behavior is affected by three additional variables: composition (within the stability range of the compound), extent of long-range order perfection, and bonding energy. Very little data are available on the effects of these variables on mechanical properties. Rachinger and ~ottrell' suggested slip to occur along (111) in compounds of low ordering energy; in compounds of higher bond strength (>0.06 ev), they observed (110) (001) slip. As pointed out by copley,' only three in- dependent slip systems are available in the latter case; hence general deformation is impossible. Brown3 carried out a theoretical calculation of the yield-point variation with the degree of long-range order in the CsCl structure, based on the assumption of superdislocations. More general approaches, based on considerations of superlattice dislocations and antiphase domain boundaries in ordered structures, were carried out by Flinn~ and by Vidoz and Brown.' These, however, give no information on changes in the slip structure—if any—between the ordered and the disordered compounds. This aspect was investigated experimentally and theoretically by Stoloff and Davies' and by Marcinkowski and chessin7 in FeCo. The latter workers proposed the deformation behavior of the ordered FeCo to be essentially the same as that in many other bcc metals. Investigations of polycrystalline A~M~'-'O indicate considerable variation in mechanical properties with composition and test temperature. The existence of {123)(111) slip was reported in AgMg.'9'9'0 (The formation energy of this compound, presumed to be ordered at all temperatures below melting, is 4.38 cal per g-atom," i.e., 0.024 ev per bond.) The yield strength has been reported as relatively independent of temperature below 0.45 T, (where T, is the absolute melting temperature). Tensile deformation of single-crystal AgMg was also investigated by Kurf-man," who observed marked tendency to single glide on{112}(111) and {110)(111). From observations of slip lines in deformed poly-crystalline NiA1, Westbrook et a1.I3 suggested the

Jan 1, 1968

By J. B. Morgan

The mechanical behavior of MgCu2 from 20 o to 725°C has been determined by "brittle-ring" tensite-test techniques, axial compression, and bending experiments. Compressive ductility begins at 450°C (0.65 T/Tm) and slowly increases with increasing temperature white the tensile ductility is characterized by an abrupt brittle-ductile transition at 600°C (0.8T/Tm). The compressive strength increases eightfold from room temperature to 400°C with a "normal" decrease as the temperature is further increased. The tensile strength goes through a rather abrupt threefold increase above 600°C with a subsequent decrease at higher temperatures. The slip system is (111)[110] and the twinning system is (111)[112]. At high temperatures MgCu2 is quite rate-sensitive, and dynamic yield points are observed that are extremely orientation-dependent. The high-temperature creep behavior under constant load is characterized by an increasing strain-rate with time. The general characteristics of the mechanical behavior make it possible to classify MgCu2 with those materials in which initial mobile dislocation density and the dislocation velocity-stress dependence are significant in determining mechanical response. Mgcu2 is the C15 prototype of the cubic Laves phase. Its range of homogeneity extends from 32.8 to 35.5 at. pct Mg at 500°C and narrows at lower temperatures. The lattice parameter is reported to vary from 7.02 to 7.05A,1 and the compound is completely ordered to the melting point of 819°C. MgCu2 has a brassy metallic appearance, is extremely brittle, and many of its physical properties are intermediate between those of the constituent elements: the electrical resistivity is 3.5 x 10-6 ohm-cm, Young's modulus is 10x 106 psi, the shear modulus is 6 x l06 psi, and the thermal coefficient of expansion is 18.7 x 10-6 cm per cm per "C from 20" to 250°C. Usually, properties of intermetallic compounds as functions of temperature have been determined by hardness, compression, or impact behavior, and almost all of these experiments have been performed on polycrystalline materials. Tammann and Dahl,2 for instance, determined the onset of ductility in a series of binary intermetallics by ball-hardness measurements and found the onset to range between 0.71 and 0.96 T/T,. Lowrie's3 investigations included some tensile properties, and he found ductility beginning around 0.65 T/Tm for most materials examined. His work did include some data on polycrystalline, nonstoichiometric MgCu2, however. The present work is an attempt to extend the examination of the particular compound MgCu2 in single-crystal form in order to aid the formation of general concepts about mechanical be-

Jan 1, 1965

By Walter V. Knopp, Laurence Delisle

The aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixtufe of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals . normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion correspending to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected.that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low COSt material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, that is, finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemelltal powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: I. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. General Procedure The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1949

By R. S. French

THE purpose of this paper is to present data that have been obtained during the past two years concerning the effects of prior cold-work and temperature and time of anneal upon the recrystallization and grain growth of 70-30 cartridge brass. It was desirable to study certain of these phases so that an accurate picture of the principles of the subject could be shown. The work is not intended to provide explicit annealing data, but to provide material examples that may help to clarify analogous problems concerning this alloy. Specifications often set limitations upon the grain size of annealed materials because of the importance of grain size upon subsequent manufacturing operations. It was, therefore, worth while to study the variables that affect the recrystallized grain size of this material. C. H. Mathewson and A. Phillips,1 W. R. Webster,2 and others have presented annealing characteristic curves of this alloy. A recent typical curve presented by R. S. Pratt3 is shown in Fig. I. The tensile properties and grain sizes are shown as functions of the annealing temperature. Such curves serve as a useful guide in determining the physical properties of annealed material, but as they are made generally under carefully controlled laboratory conditions they do not indicate the performance of metal annealed in a mill muffle, where conditions are different and the amounts of metal require necessarily longer heating times and temperatures. Study of the effect of time and temperature upon grain growth and subsequent recrystallization was made with a coil of metal having the following analysis: 70.04 per cent copper; 0.007 lead; 0.007 iron; 0.00 tin; 0.00 silicon; 0.001 nickel; 0.000 phosphorus; balance zinc. The sample coil was obtained from metal that had been rerolled from hot-rolled mill stock, and was received at 0.228-in. gauge, soft, with a grain size of 0.125 mm. This material was then rolled 43.5 per cent to 0.125-in. gauge and annealed to a 0.053-mm. grain size. In this condition, samples were cut and used in all of the experimental work reported in this paper. TIME The first study was of crystal growth at a constant temperature over a moderate length of time. Material was cut from the stock coil at 0.129-in. size and rolled 75 per cent hard to 0.032-in. gauge. From this piece small samples were cut ½ by 2 in., suitable for grain-size determinations. Twelve samples were placed in an electric furnace uniformly across the width, approximately an inch from the floor, A thermocouple was wired to the center sample, so that the approximate metal temperature could be followed. At various

Jan 1, 1944

By Walter V. Knopp, Laurence Delisle

INTRODUCTION THE aim of this work was the preparation of nickel-steels from elemental metal powders by powder metallurgy techniques. It was known that plain carbon steels could be made from a mixture of iron powder and graphite and that the effect of carbon on iron in powder form was of the same nature as that produced in fusion metallurgy. The problem in making nickel steels from elemental powders consisted therefore in finding out whether sufficient diffusion of the nickel and other incidental metals normally present in such steels could be induced in the solid state to modify the properties of plain carbon steels made from powders and produce the beneficial effect of alloying. The composition selected originally was that of an S.A.E. 2330 steel. Metal powders, in the proportion corresponding to that composition, were mixed with graphite, pressed, and heated at different temperatures for different periods of time, to produce bonding of the metal particles and mutual diffusion of the various elements without melting. Temperatures up to 1325°C and sintering periods as long as 6 hr were first investigated because it was expected that such conditions would produce maximum diffusion with an accompanying improvement in the properties of the alloy. It was found that, although diffusion proceeded to a large extent under the conditions investigated, it would not be complete unless sintering were carried out at a high temperature for much longer than 6 hr. Relatively high temperatures and long sintering times are objectionable from a practical point of view, particularly when a low cost material is to be produced, because they necessitate the use of special, costly equipment. Work could be done to improve the diffusion of iron and nickel by changing conditions other than the sintering temperature and time, i.e., finer primary or alloy powders could be used. However, a marked change in the properties of the steel had been observed even with only partial diffusion. It was thought, therefore, that instead of trying to improve the diffusion, advantage might be taken of its incompleteness to produce a special structure consisting, in the unquenched condition, of a hard constituent, rich in nickel, dispersed in a tough pearlitic matrix. Steels with such a structure, not readily obtainable by fusion, should have desirable mechanical properties. Besides, it should be possible to prepare them from elemental powders under economical conditions. This latter alternative was therefore adopted for the second phase of this work. This report is divided into four parts: 1. General Procedure. 2. Effect of Sintering Temperature. 3. Effect of Varying the Nickel Content. 4. Effect of Alloying Elements. GENERAL PROCEDURE The general technique of cold pressing as used in powder metallurgy was applied.

Jan 1, 1948

By H. E. Elliott, R. S. Busk, A. T. Peters

One of the problems of the fabricator of metals and alloys is the propensity of some composition rarnges toward abnoermal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, 9 per cent A1, 2 Per cent Zn, 0.2 Per cent Mn) and G alloy (Mg, 10 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other meta1s- Jeffries and Archer1 have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. Before recent developments, this phenomenon of abnormal local grain growth Was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. I) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The DOW Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germinasium since this term has been definedl as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By H. E. Elliott, R. S. Busk, A. T. Peters

ONE of the problems of the fabricator of metals and alloys is the propensity of some composition ranges toward abnormal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, o per cent Al, 2 per cent Zn, 0.2 per cent Mn) and G alloy (Mg, i0 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other metals. Jeffries and Archer' have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. of abnormal local grain growth was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. r) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The Dow Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germination," since this term has been defined' as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By C. R. King

Most of the acid volcanic glasses such as obsidian, perlite, pitchstone, pumice, and pumicite (volcanic ash) are susceptible to some expansion if suddenly subjected to a suitably high temperature in a properly designed furnace, and subsequently suddenly cooled. Expansion results from the action of chemically combined or dissolved water expanding as a vapor within the softened heated rock particles. This expansion forms countless minute bubbles within the pasty mass of the natural glass particles. If the particles are cooled before these bubbles can escape, the resulting products are cellular, more or less spherulitized glass froths or hollow glass spheres of many types. Chemically, they are essentially aluminum silicates containing about 70 to 75 pct silica, 10 to 16 pct alumina, and 2 to 7 pct sodium plus potassium oxides. They are relatively resistant to attack by acids or alkalies, are resistant to heat up to over 1000°F, and are completely inert to insect or fungus attack. These products are of great potential value in many branches of industry as insulation materials, aggregates, fillers, abrasives, and additives. By proper selection of the perlite rock type and control of processing conditions, expanded perlite of a bulk density varying from about 2 to 20 Ib per cu ft can be • made. The physical properties of the particles comprising a product of a given bulk density also may be varied within wide limits of porosity, water absorption, and crushing strength. In general, crushing strength of expanded perlite increases in direct relation to increase in bulk density, but insulating value varies in inverse ratio to bulk density. The selection of a particular grade of expanded perlite for a given use as an aggregate is therefore always a compromise between insulating value, lightness, and friability. If porosity and water absorption are factors affecting the use of the material, factors other than bulk density are important. Some types of perlite rock tend to decrepitate excessively during expansion, resulting in a highly porous or even hygroscopic product of high friability relative to the bulk density of material produced. In general, treatment of any good perlite rock below the temperature necessary for maximum expansion, or insufficient time in the hot zone of the furnace for effective heat penetration to the core of the rock particles will result in some decrepitation and high porosity in the expanded product. On the other hand, exposure of the material to the temperature required for optimum expansion for a period of time slightly longer than that necessary for proper heat absorption will result in a slightly heavier product of extremely low porosity, i. e., a glazed surface. It is beyond the scope of this paper to describe in detail the rock types and processing methods used to produce the many types of expanded perlite in present use, or that may be produced to fill the present and future needs of industry. A few phases of the economics involved in processing and selling products made from this abundant and cheap mineral raw material, plentifully distributed in large and relatively accessible deposits in most western states and in other areas within economic shipping distance of large centers of consumption, will be treated with particular reference to the Los Angeles area. Relation of Balk Density to Use and Cost of Production Perlite differs from most other lightweight aggregates and fillers in that the raw material (perlite rock) may be quarried much as rock arid sand is mined, and then shipped into consuming areas as crude rock in open gondola cars at correspondingly low freight rates and handling costs. At processing plants in or near large consuming areas the rock is converted into relatively fragile, very bulky products which in most cases are used within a short haul of the processing plant or enter into a manufactured product made at the site of the perlite processing plant.

Jan 1, 1950

By T. J. Koppenaal

The surface slip line structure has been investigated by optical microscopy during the easy glide deformation of Cu-A1 single crystals as a function of composition, testing temperature and prior thermal treatment. The slip line structure in alloys of 2.5 or less at. pct Al is similar to pure copper, while alloys of 5 or more at. pct Al show slip tracings typical of a brass. Cross slip is observed in the "a-brass type" crystals and the amount of this type of slip increases rapidly with aluminum content. The cross slip tendency in 14 at. pct Al crystals is signicantly higher when tested at 150°C as compared to 4.2" and 77°K. In addition, cross slip is more pronounced in this alloy in the furnace cooled condition than when quenched from 450°C. The cross slip behavior is analyzed in terms of existing models for this type of deformation. In two previous investigations, reports of yield points1 and solid solution strengthening2 in Cu-A1 single crystals have been given. This paper enlarges upon the brief description of the slip line structure discussed in these reports. Since the easy glide slip line pattern of copper changes markedly with the addition of -30 pct Zn (-brass),3 a study of slip lines as a function of solute additions in Cu solid solutions should help to explain some of these differences. In addition to composition variables, slip lines have also been studied as a function of testing temperature and prior thermal treatment. PROCEDURE The slip line observations were made on single crystals of 0.5 to 14 at. pct Al using a light microscope. Details concerning the preparation and basic testing procedure are given elsewhere.' Prior to testing, each crystal was homogenized at 900°C for 24 hrs, furnace cooled, and electrolytically polished in a 60 pct phosphoric acid solution. The strain rate was-5 X 10 sec-I in each case. Unless otherwise stated, all observations reported upon here were made during the early stages of easy glide. RESULTS AND DISCUSSION The maximum magnification generally used was 1000X, and slip lines could be resolved down to about 105 cm (1000A). This resolution is appreciably less than obtainable with electron microscopy replica techniques where the replication can resolve slip lines down to about 40 A. Thus, while many qualitative features could be studied, the type of quantitative data obtainable with an electron microscopy replica study could not be made. Crystals containing 0.5 and 2.5 at. pct Al deform much like pure copper exhibiting a high density of fine slip lines that cover the entire gage length of the specimens. Fig. 1 shows the surface slip line pattern in a 2.5 at. pct A1 extended 0.01 shear strain at room temperature. Crystals having 5 to 14 at. pct A1 showed appreciably coarser slip lines that were generally concentrated at one end of the gage length. During easy glide these coarse slip lines propagate along the gage length in a manner similar to that observed in a-brass single crystals by Piercy, Cahn, and cottrel14 and refered to by them as a Lüders band propagation. Fig. 2 shows a typical area of these coarse slips in a 14 at. pct A1 crystal after a room temperature shear strain of 0.01. Two slip systems were apparently active. Using a method described by Cullity, the angles, between the specimen axis and the normals of the primary and secondary slip planes were determined to be 50 and 84 deg, respectively. 'From the Laue photograph, was 52, 81, 66, and 30 deg for the primary, cross, conjugate, and fourth slip planes, respectively. The secondary active plane in Fig. 2 is thus established as the cross slip plane, and the operative slip system is evidently the cross slip system, e.g., slip

Jan 1, 1963

By P. S. Kotval, H. Hahell

PRECIPITATION of M23C6 carbides at grain boundaries in austenitic steels and nickel base superalloys has received considerable attention. Hatwell and Berghezan,1 in a study using carbon extraction replicas, observed that dendritic growth of the M23C6 carbide phase occurred at grain boundaries in austenitic steels. Merrick and Nicholson2 have observed that in thin foils of "Nimonic 75" alloy the precipitation of M23C6 carbide was discontinuous at grain boundaries. Lewis and Hattersley3 have suggested that the type of M23C6 precipitation observed in Ni-Cr austenites represented the early stages of discontinuous precipitation. In a more recent study, Singhal and Martin4 have concluded that grain boundary M23C6 precipitation involves the migration of an austenite grain boundary by a mechanism very similar to that proposed by Tu and Turnbull.5 Tu and Turnbull's suggestion essentially involves grain boundary migration under the driving force arising from the difference between the surface free energies of the opposite sides of the plate. Thus, Singhal and Martin's observation4 implies that the first stage of discontinuous precipitation has taken place and that the grain boundary has provided a diffusion short circuit for the sub-stitutional solute atoms (principally chromium) which assist the preferential growth of the M23C6 plate in contact with the grain boundary. However, no evidence of the characteristic cellular morphology typical of discontinuous precipitation was found in Singhal and Martin's studies. Presumably, this is due to the low volume fraction (i.e., low supersaturation of solute) of the precipitating carbide reported by Singhal and Martin.4 Recently, Raymond6 has studied precipitation of the M23C6 carbide in Incoloy alloy 825 and shown that the growth of this phase is perpendicular to grain boundaries at 1400°F and in the plane of the grain boundary at 1700°F. The former aging condition resulting in discontinuous or "cellular" precipitation. Raymond has suggested an explanation for this behavior based on the relative rates of chromium diffusion by volume and grain boundary diffusion at the two different aging temperatures. In the course of a recent investigation on precipitation behavior in several ' strengthened superalloys, precipitation of M23C6 carbide at grain boundaries was studied. Under conditions of a high degree of supersaturation, the M23C6 carbide precipitates in the discontinuous or cellular morphology in Waspalloy (Ni-18.51 Cr-2.0 Fe-3.53 Mo-1.16 Al-2.78 Ti-0.09 C). This note presents electron microscopy observations of this mode of precipitation and its effect on mechanical properties. Specimens of Waspalloy after "solution" heat treatment at 1950°F show essentially single phase matrix with a few residual particles of "primary" MC carbide. In normal commercial heat treatments, precipitation of Ni3(Al,Ti) ordered fcc r' phase occurs throughout the matrix and M23C6 precipitates as globular particles at the grain boundaries. In these commercial heat treatments the degree of supersaturation during precipitation is low. However, if specimens of Waspalloy are quenched from the solution heat treatment temperature of 1950°F and then aged at an aging temperature where the degree of supersaturation is high, discontinuous precipitation of M23C6 occurs. Figs. 1 and 2 show thin foil micrographs of Waspalloy, solution heat treated at 1950°F, water quenched, and aged at 1292° and 1598°F, respectively, for 500 Fig. 1—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 500 hr at 1292°F. Magnification 15,500 times. Fig. 2—Thin foil of Waspalloy, solution heat treated at 1950°F for 1 hr, water quenched, and aged for 114 hr at 1598° F. Magnification 13,000 times.

Jan 1, 1970

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By H. F. Webster, C. G. Dunn

Rolling md annealing procedures are described for developing the (110) preferred orientation in tantalum for use as a thermionic-emission materinl where electrodes of a uniform high work function are needed. The development of a (110) [001] annealing texture is also reported. A preferential growth process due to low (110) gas-metal surface energy is considered in explanation of the observed growth of (110) grains. ThE growth of (110)-oriented grains in thin strips of rolled zone-refined tantalum, previously discussed briefly,' is reported together with more recent information on the formation of a (110)[001.] annealing texture, i.e., one where the [001] direction of each grain lies close to the rolling direction. The development of tantalum sheet with a (110) preferred orientation (position of [001 ] directions unspecified) is of importance as a thermionic-emission material in thermionic-energy converters. Since therm ionic-emission properties of cesium-coated crystals vary over a wide range depending on (hkl) a2-7 a single (hkl) preferred orientation is more useful than either several preferred orientations or none. Furthermore, the (110) preferred orientation yields the highest thermionic-emission density for a cesium coverage of less than a monolayer.5-7 A consideration of the stability of the grain structure needed at high operating temperatures suggests that the preferred orientation itself should be produced by annealing processes. Information on annealing textures in tantalum, however, is rather limited. Pugh and Hibbard 8 obtained (111)[112] and (lll)[112] components in a 1400°C recrystallization texture in 95 pct cold-rolled foil; these components were enhanced on annealing at 2500°C. Muller9 rolled 99.97 Ta to 90 pct reduction in thickness in the final stage and noted only a slight sharpening of the rolling texture, with some intensification of the (111)[112] component upon annealing at 1200°C. The experimental procedure followed in the present work stemmed from the idea of using possible differences in (hkl) surface energies to provide a small driving force for growth of grains having the lowest (hkl) surface energy.l0* This would mean using high-purity tantalum processed into thin sheet form and annealed at high temperatures either in a noncontaminating atmosphere or in one producing additional sample purification. EXPERIMENTAL Zone-Refined Tantalum. National Research Corp. tantalum in the form of 1/8-in.-diam rod and of 99.98 purity (53 ppm 0, 15 ppm N, and 8 ppm C) was zone-melted four times. The traversing speed was 4 mm per min. Such treatment increased the resistance ratio, R293k/R20K , where R293K is the resistance of the specimen at 20°C and R20K the re-resistance at liquid-hydrogen temperature, from a value of 25 for the initial rod to 175 for the zone-refined rod (the increase in the resistance ratio provides a measure of purification11,12). Part of a zone-refined rod was rolled unidirec-tionally to a strip 0.003 in. thick and 0.28 in. wide. Samples were given anneals in the range 1300" to 2100°C using ac conduction heating in an oil-free vacuum system. Recrystallization to small grains appeared to be complete at 1300°C. Large grains were formed at higher temperatures, but these were not entirely strain-free, some grains showing asterism in Laue X-ray patterns and some displaying a range in orientation. Part of the difficulty was caused by thermal expansion of the tantalum strip as it was held between fixed supports. However, in a different arrangement with the tantalum freely suspended in a tantalum can, high-frequency induction heating in vacuo at about l0-6 Torr produced

Jan 1, 1964

By Mason K. Banks

A process has been developed which produces spodumene concentrates assaying 6.0 pct Li2O and 0.45 pct Fe2O3, with 70 to 75 pct recovery of spodumene. Two flotation separations are required: the simultaneous removal of mica, feldspar, and quartz as a froth product using a cationic collector, and the subsequent removal of iron-bearing minerals as a froth product while spodumene is depressed as a tailing. SINCE the close of World War II there have been numerous developments resulting in the increased use of lithium by industry. Notable among these has been the development of an industrial lubricant, based on lithium stearate, which is fluid at low temperatures, stable at high temperature, and insoluble in water. A new bleaching agent, lithium hypo-chlorite, has also been developed recently.' Other well-known uses are listed below: 1—Lithium oxide in ceramics reduces firing time, lowers melting temperatures, lowers thermal expansion, raises refractive index, and improves chemical resistivity. 2—Lithium carbonate and lithium strontium nitrate are used in pyrotechnics for their brilliant red color.' 3—Lithium chlorides and fluorides are used as fluxes for welding aluminum and magnesium.' 4—The affinity of lithium for nitrogen is the basis for a process used in purifying helium." 5— Lithium chlorides and bromides are used in air conditioning for their powers to absorb organic amines, ammonia, and smoke.6-—Lithium hydride has been used as a source of hydrogen to inflate life rafts and balloons used by the Air Forces and Navy.' 7— Lithium metal and lithium hydride are useful in the atomic energy program in connection with the production of the isotopes of hydrogen." During the 1942-45 period of World War 11, Solvay Process Co. operated a flotation plant with a daily capacity of 300 tons of ore for the production of spodumene concentrate near Kings Mountain, North Carolina. The operation was shut down upon reduction of wartime demand for lithium chemicals, and until recently there has been no production from the Carolinas. In April 1950 an investigation of the problem of spodumene flotation from North Carolina ores was begun at North Carolina State College Minerals Research Laboratory at Asheville, N. C. This laboratory, operating under the combined auspices of North Carolina State College, North Carolina Department of Conservation and Development, and the Tennessee Valley Authority, undertook the spodumene project at the request of Foote Mineral Co. of Philadelphia. The work, involving a period of 15 months of intensive batch and pilot plant investigation, was completed in June 1951 and resulted in development of a process for concentration of spodumene by flotation which has been hereto unrecorded in the literature. A similar approach has been used before on iron, ilmenite, and other minerals, but the literature shows no record of its having been applied to spodumene. Parts of the process are now being used on a commercial scale at the Foote Mineral Co. plant near Kings Mountain, N. C., which has been in production since July 1951. It is the purpose of this paper to describe some of the results of the investigation. The Orebodies Spodumene-bearing pegmatites occur in a narrow belt 24.5 miles long and 1.8 miles wide extending southwestward from Lincolnton to Grover, N. C. According to statements judged to be conservative, the tin-spodumene belt of the Carolinas contains an estimated 4,300,000 tons of pegmatite ore averaging 15 pct spodumene. This amounts to "a reserve of at least 650,000 tons of spodumene (more than 20,000 tons of metallic lithium) to a depth of 100 ft."' This figure includes only bodies having an average thickness of 35 ft and length of 550 ft. There are hundreds of pegmatites in the belt, many of which are less than 10 ft wide. The largest pegmatite in the area has a maximum thickness of 395 ft and maximum length of 3250 ft.' These larger pegmatites are composed principally

Jan 1, 1954

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By R. A. Morse, C. R. Stewart, F. F. Craig

This paper preFents the results of a series of model flow test on a number of large limestone cores, having different pore configurations. For limestone cores having substantially sandstone type porosity, the production characteristics for solution and external gas drives are similar. For cores whose pore spaces were microscopically heterogeneous (i.e., consisted of combinations of solution cavities, matrix. and fissures), the production characteristics lor solution and external gas drives vary widely. The degree of divergence between gas-oil relative permeability relationships calculated from solution or external gas drive tests is an indication of heterogeneity of rock pore structure. The results of water floods on cores depleted by solution gas drive for each of these two general types of limestone porosity are also shown. Generalizations are made on the water flood recovery that could be expected from each of these two types of limestone porosity. The similarity between solution drive field performance and model solution drive performance on cores from the same formation is shown for several cases. This indicate? the feasibility of predetermining limestone field performance from such large core tests. Photomicrographs of plastic-impregnated rock thin sections of the samples tested are presented as an aid in understanding the flow test performances. INTRODUCTION During the past 15 years. reservoir engineers and research workers have developed methods of testing rock and fluid samples and applying the results, through calculation, to allow reasonably satisfactory predictions of oil recoveries and performances to be expected in sandstone oil recervoirs. It has been determined that representative fluid flow data can be obtained on rock samples as small as three-fourths in. in diameter by one in. long in most sandstones. However, little has been accomplished toward the laboratory determination of fluid flow characteristics in limestones. There has been a great deal of speculation as to the influence of variations in pore size, shape, and degree of interconnection upon oil recovery processes, and a great deal of thought has been given to the interpretation of limestone field perfomance. It has been generally recognized that predictions of reservoir performance based on oil displacement tests on small limestone core samples the size of those used for sandstone tests can often be misleading because of the improbability of obtaining a representative sample in such a small core. Obviously, if there are present in the rock, pore openings of the magnitude of 1/16 in., or fractures or solution channels up to one in. or more in length, it will be impossible to cut any sample less than one in. in any dimension which would represent the flow geometry of the gross rock system. In some formations, the individual openings in the rock are of such size that it would be impossible to obtain a good sample of the flow system even in the total core available from conventional-sized well cores. However, by increasing to the maximum the size of the sample used, it should be possible to obtain representative flow data from the majority of limestone reservoir materials which can be used for prediction of future primary production performance or response to be expected from secondary recovery measures. The only alternatives to obtaining good laboratory test data to serve these purposes are extrapolation of primary performance data obtained by partial depletion of a field, or obtaining information from pilot tests. It has been shown previously, and will be demonstrated further by the work reported in this paper, that extrapolation of solution gas drive performance for an estimate of gas injection response can be very misleading in reservoirs of heterogeneous type porosity. Although it cannot be expected that laboratory information can ever eliminate the necessity of small-scale pilot operations, it is expected, as is now the situation with sandstone reservoirs, that laboratory tests should provide reliable information for screening of

Jan 1, 1953

By E. C. W. Perryman

IN spite of the large amount of work which has been carried out on the recrystallization of aluminum and its alloys, there has been no complete investigation of the recrystallization characteristics of A1-Mg alloys. The most complete investigation is that reported by Bungardt and Osswald' who, working with commercial-purity materials, found that the temperature both of beginning and of complete recrystallization increased with magnesium content up to about 2 pct Mg, then decreased with a further increase in magnesium up to 5.0 pct, and thereafter increased again. Michaud and Segolz working with 99.93 pct A1 also found the temperature of beginning of recrystallization to decrease as the magnesium content increased from 2.13 pct to about 4.5 pct. Chossat3 using aluminum of 99.99 pct purity found that 0.12 pct Mg had no effect but that 0.4 pct Mg increased the recrystallization temperature by about 30°C. That no effect was found for 0.12 pct Mg does not agree with the later results reported by Demer and Beck4 who found that 0.025 pct Mg in 99.99 pct A1 increased the time for complete recrystallization and furthermore increased the activation energy for the recrystallization process. Kratz" using 99.997 pct A1 found that 0.5 pct Mg increased both the temperature of beginning and of complete recrystallization by 100°C. Chadwick and Hooper" working with commercial-purity material found that 1 pct Mg increased the temperature of complete recrystallization by about 40 °C for cold reductions in the range 17 to 72 pct. With smaller amounts of cold work produced by stretching (10 pct strain), they found no significant effect of magnesium. The latter result agrees with that obtained by Williams and Eborall' who found no effect of 2 pct Mg on the recrystallization temperature of commercial-purity aluminum strained 10 pct or less by stretching. Experimental Procedure Material Used: The chemical analyses of the materials used throughout this investigation are given in Table I. Fabrication: The alloys were cast in iron molds which had been washed thoroughly with alumina. After scalping, the ingots were annealed for 16 hr at 450°C, pressed, annealed at 450°C for 16 hr and hot rolled to 0.25 in. After hot rolling, the slabs were alternately annealed and cold rolled to 0.036 in. Cold-rolling reductions between intermediate anneals were kept at about 30 pct and a high intermediate annealing temperature of 450°C was used so as to obtain, as nearly as possible, similar starting grain sizes for the different materials. All intermediate anneals were done in a salt bath and were followed by cold-water quenching so as to retain all the magnesium in solid solution. The final cold reductions investigated were 20, 30, 40, 50, 60, and 80 pct. The initial grain sizes, that is, the grain size before the final cold reduction, were all very similar. Annealing Procedure: Specimens, 1 in. sq, were cut from the 0.036 in. sheet and annealed in a salt bath, the temperature of which was controlled to k2"C. Separate specimens were annealed for different times at 350°, 375", 400°, and in one or two cases at 415°C and after annealing were quenched in cold water. The time taken for a specimen to reach temperature was approximately 5 sec. Metal-lographic examination after annealing showed that no precipitation of Mg+413 occurred during cooling. Procedures Used for Determining Recrystallization Characteristics: All specimens were electrolyti-cally polished and etched by the method described previously1° and polishing was continued until about 0.002 in. had been removed from each side of the specimen. Using this technique, the smallest recrys-tallized grain which could be observed with cer-

Jan 1, 1956

By T. K. Perkins, O. C. Johnston

Because of the influence of dispersion on miscible-displacement processes, diffusion and dispersion phenomena in parous rocks are of current interest in the oil industry. This paper reviews and summarizes a great deal of pertinent information from the literature. Porous media (both unconsolidated packs and consolidated rocks) can be visualized as a network of flow chambers, having random size and flow conductivity, connected together by openings of smaller size. In such a porous medium, the apparent diffusion coefficient D is less than the molecular diffusion coefficient Do, as measured in the absence of a porous medium. For packs of unconsolidated granular material the ratio D/D, is about 0.6 to 0.7. For all porous rocks, both cemented and unconsolidated, the ratio of diffusion coefficients can also be represented as D/Do = 1/FF where F is the for- mation electrical resistivity' factor and 4 is the porosity. If fluids are flowing through the porous medium, dispersion may be greater than that due to diffusion alone. At moderate flow rates the porous medium will create a slightly asymmetrical mix zone (trailing edge stretched out), with the longitudinal dispersion coefficient approximately proportional to the first power of average fluid velocity (if composition is nearly equalized in pore spaces by diffusion). If the velocity in interstices is large enough, there will be insufficient time for diffusion to equalize concentration within pore spaces. In this region, longitudinal dispersion increases more rapidly than fluid velocity. At low velocities in interstices, transverse dispersion is characterized by a region in which transverse diffusion dominates. If the fluid velocity gets high enough, there will be a transition into a region where there is stream splitting with mass transfer but with insufficient residence time to completely damp-out concentration variations within pore spaces. There are several variables that must be con- trolled to get consistent longitudinal and transverse dispersion results, viz., (1) edge effect in packed tubes, (2) particle size distribution, (3) particle shape, (4) packing or permeability heterogeneities, (5) viscosity ratios, (6) gravity forces, (7) amount of turbulence, and (8) effect of an immobile phase. INTRODUCTION Diffusion and dispersion in porous rocks are of current interest to the oil industry. This interest arises because of the influence of dispersion on miscible-displacement processes. In a recovery process utilizing a zone of miscible fluid, there is the possibility of losing miscibility by dissipating the miscible fluid or by channeling or "fingering" through the miscible zone. Diffusion and dispersion are two of the mechanisms that may lead to mixing and dissipation of the slug. On the other hand, dispersion may tend to damp-out viscous fingers which may be channeling through the miscible slug. 58 Hence, dispersion may be detrimental or beneficial (if it prevents fingering through the miscible zone). Therefore, it is doubly important that we understand these processes. In this paper we review, summarize and interpret a great deal of information from the literature. In particular, we will briefly discuss molecular diffusion in miscible fluids. Then we will discuss what differences to expect for diffusion in a porous rock. If there is movement of the fluid through the rock, then there may be an additional mixing or "dispersion". Furthermore, the dispersion longitudinally (in the direction of gross fluid movement) and transverse to the direction of fluid movement will not be equal. We will discuss both types of dispersion as well as several variables which can affect dispersion (viscosity differences, density differences, turbulence, heterogeneity of media, etc.). This group of variables has sometimes led to difficulty when comparing literature data. DIFFUSION OF MISCIBLE FLUIDS If two miscible fluids are in contact, with an initially sharp interface, they will slowly diffuse into one another. As time passes, the sharp interface between the two fluids will become a diffuse

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963

By A. E. Anderson, H. J. Hilll

Laboratory data for 155 field muds and 77 .shales have been used to develop correlations to estimate the net streaming potential component of the SP. Analysis of these data and comparison with field tests show that streaming potential corrections must be made to obtain an accurate estimate of the electrochemical potential for use in the determinntion of formation water resi-iiviy. The self-potential curve is related to formation water resistivity, and considerable effort within the oil industry has been directed toward clarifying this relationship. The Schlumbergers and Leonardon1,2 recognized that two types of potentials, electrochemical and electro-kinetic, resulted in the net potential variation in the borehole. Most of the later papers have dealt with the electrochemical component and its controlling parameters. The investigations of Wyllie,2" Salisch' and Moore5 provide the most extensive sources of data on streaming potentials across mud cakes. These authors observed streaming potentials of sufficient magnitude to be of critical importance in SP interpretation, if it is assumed that streaming potentials develop only opposite permeable beds. Streaming potentials across shales have been reported by Schenck and by Gondouin, et al.7 Since SP magnitude is the difference in potential opposite shale and sand beds, these authors suggested that the net streaming potential component may be negligible. The present investigation was initiated to evaluate empirically some of the parameters controlling the magnitude of the net borehole streaming potential and to determine whether useful relations between mud properties and net streaming potential could be established. Field muds were used in this investigation. These muds were characterized by the amount and type of chemical treatment utilized for five days before Sampling. Filter loss, mud resistivity, mud density and filtrate resistivity were determined for each mud with conventional methods and apparatus. Mud filtrate pH was estimated with Hydrion pH paper for the appropriate range. Streaming PotentIals Across MuD Cakes Commercial calomel-saturated KC1 electrodes are subject to potential changes attributed to contamination of the very small fiber-tip bridge by particles of clay from the drilling mud.3 To minimize this difficulty, a large diameter bridge (Fig. 1) was constructed with saturated KC1-agar gel and a filter disc of microporous porcelain. Experiments showed that streaming potentials across this bridge are less than 0.2 mv at pressure dif-

By E. L. Affleck, W. G. Stevenson

In both Canada and the United States, a company making a public offering of securities must comply with regulations which have been passed by Federal, State and/or Provincial Legislatures. These regulations usually require the distribution of an acceptable prospectus which provides essential background information about the issuer, the project and the share offering. when the public offering has been accepted, the unlisted company may then seek a listing of its shares for trading on a Stock Exchange. Once listed, the company will be subject to rules of the Stock Exchange. This paper will deal with the specific information required for inclusion into a prospectus being submitted for a resource company and particularly those parts of concern to mining engineers and geologists.

Jan 1, 1985