Search Documents

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

By G. B. Gould

Every mathematical statement of a measure of anything (as distinguished from a count') is followed by a qualification—always implied if not explicity stated—-that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accuracy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applications—and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this question of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject themselves. There is great need for more widespread understanding of what lias been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments. Determining Deviations in Quality It is necessary at the outset to distinguish between: (I) the accuracy with which one test indicates the quality on one lot of coal; and (2) the accuracy with which a test of one lot of coal represents the average quality of a commercial product, of which the buyer will presumably receive a series of shipments—perhaps many thousands of tons. It is necessary to make this distinction because coal is a variable material—a heterogeneous mixture of a variety of components—the quality of which will vary from one lot to another. Therefore an absolutely accurate determination of the quality (if that were possible) of one lot of a coal is an

Jan 1, 1938

In the past few years the hydraulic aspects of rotary drilling have received considerable attention. It is generally recognized that accurate prediction of circulating pressures is desirable, particularly in those areas where a delicate pressure balance is necessary to prevent both blowouts and lost circulation. For calculation purposes the standard hydraulic equations for the pipeline flow of Newtonian fluids have been altered to facilitate similar calculations for non-Newtonian or plastic fluids.'.' This latter classification includes most colloidal types of drilling muds. Two properties: plastic viscosity, un, and Bingharn yield value, Y,, are commonly used to define the flow characteristics of a plastic fluid. These are commonly obtained with multispeed viscosimeters such as the Fann V-G meter.3 Normally these measurements are obtained at some surface temperature, and are not corrected to circulating temperatures for calculation purposes. This may result in considerable error, particularly in the laminar flow calculations which comnlonly apply to the drill pipe-borehole annulus. The purpose of this study was to investigate the effect of temperature on the flow properties of some water-base muds. A laboratory model Fann V-G meter was used for measurement of viscosities, yield values and gel strengths. An aluminum water jacket with O-ring seals was machined to fit around the mud cup of the Fann meter. All mud samples were prepared by thorough mixing in a Hobart mixer. Viscosity and gel strength measurements were made with the Fann meter using standard procedures. Flow properties of muds were studied at 80, 120, 160 and 180°F. The compositions of the test samples are given in Table 1. The typical effect of temperature on the flow properties of these drilling muds is illustrated by Fig. 1. It was found that plastic viscosity and apparent viscosity decreased with an increase of temperature. However, the curves were not linear, and did not appear to follow any definite trends or patterns. Yield point data showed much more scattering.' Since a usable method for predicting drilling mud flow behavior with temperature was desired, an attempt was made to find a simple relationship between these variables. The basic approach used by Havenaars for predicting the same effect on turbulent viscosity resulted in Fig. 2, which shows that

By John D. Sullivan

Leaching of copper ores is a comparatively old art, probably dating back to medieval times. The leaching of mixed oxidized-sulfide ores, however, is modern. The first modern plant leaching mixed ores was at Ajo, Ariz., where commercial operations commenced in 1917. While the ore at Ajo was primarily oxidized there was always some sulfide present. The Inspiration leaching plant, which was put in operation in 1926, may be considered the first plant constructed for the extraction of both sulfide and oxidized copper. The pioneers in leaching mixed ores had a difficult task before them since they had very little fundamental data on the chemical and physical factors of leaching. For the very large amount of painstaking experimental work that was done before building the Ajo and Inspiration leaching plants the reader is referred to the original articles.' For a period of several years the writer worked on problems connected with the chemistry and physics of leaching mixed oxidized-sulfide ores. This paper summarizes the experimental work and discusses various factors involved in leaching ores. It also presents many data heretofore unpublished. Among the new data are those on chrysocolla, pages 518 to 519, inclusive; dioptase, page 519; covellite, page 529; virtually all those on chalcopyrite, pages 531 to 533, inclusive; enargite, page 533; and tetrahedrite and tennantite, pages 534 and 533. The oxidized copper minerals of commercial importance in American ores are azurite, Cu3(OH)2(CO3)2; malachite, Cu2(OH)2CO3; chrysocolla, CuSi03.2H2O; tenorite (or melaconite), CuO; and cuprite, Cu2O. Dioptase, CuSiO3.H2O is less common. Brochantite, CuSO4.3Cu(OH)2, while the chief mineral in the ore at Chuquicamata, is not of major importance in the United States. Metallic copper, while chemically not so, is frequently classed as an oxidized mineral of copper. The most important sulfide minerals are chalcocite, Cu2s; covellite, CuS; bornite, Cu5FeS4; and chalcopyrite, CuFeS2. Less important complex sulfides are enargite,

Jan 1, 1934

By H. D. Kynor

By the term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal and Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal and Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910" is as follows: Penna. Coal Co. D. L. & W.. ScRanton Temple Hudson YeaR and Hill- Tons Coal Co., Coal Co., Coal Co., Total, side Coal Tons Tons Tons Tons and Iron. Tons 1920................ 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919................ 950,786 no record 306,616 81,575 319,356 1,658,333 1918................ 917,778 744,966 24,880 44,756 288,781 2,021,161 1917................ 757,940 838,800 5,050 57,279 164,180 1,823,249 1916................ 286,780 860,663 13,960 114,173 101,475 1,377,051 1915................ 428,819 592,169 8,253 1,029,241 1914................ 219,188 153,896 373,084 1913................ 171,505 1912................ 124,267 124,267 1911................ 40,319 40,319 1910................ 1,184 1,184 a A slightly greater production was obtained than here indicated, as the tonnage from individual operations is not shown. b Decrease due to strike conditions in 1920. c Does not include tonnage of D., L., & W. d D., L., & W. decrease in 1920 due to having fewer mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 1, 1922

By A. M. Gaudin

The study that is presented here was undertaken in order to condense information concerning comminution, and covering a great variety of conditions, into one or several rules which would be of use in the development of a systematic theory as well as in many directly practical ways. As the result of this work, the following conclusions appear justified: 1. Rocks may be classified, from the point of view of comminution, into two general classes which are (a) structurally homogeneous, and (b) structurally heterogenous. Structurally homogeneous rocks are those in which fracture takes place through grains and grain boundaries alike; heterogeneous rocks are those in which fracture passes in preference through grain boundaries. 2. If a sized product composed of structurally homogeneous rock grains is crushed, a product results in which the relation between the percentage weight of grains of various sizes and these sizes themselves follows a definite law. This is not true of structurally heterogeneous rocks. 3. Ball milling with structurally homogeneous rocks, and under certain conditions, presents exceptions to this rule. 4. In ball milling with structurally homogeneous rocks, there exists a critical ratio of size of feed to size of balls, above which the machine operates essentially by surface wear, and below which it operates essentially by breaking across the body of the particle. 5. In ball milling, with structurally homogeneous rocks, and when the size of feed grains exceeds the critical size, the particles worn off are of a substantially definite size which depends upon the ball size. 6. In the case of a typical heterogeneous rock, such as Manhattan schist, particles are crushed in such a way that there is a greater proportion of grains of the size that is the average grain-size of the rock than there would be in that range of size with a structurally homogeneous rock. This has been found to be true with all the crushers tested. 7. Different methods of crushing produce grains of different shapes. 8. The importance of sizing the — 200-mesh portion of a crushed product, in crushing-efficiency investigations, has been greatly under-

Jan 1, 1926

By R. W. Raymond

THE absence of a convenient glossary of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as may be inferred from its great increase in length, as well as the numerous alterations which it has undergone. It could certainly be still further enlarged and improved; but I think a comparison of it with any of the glossaries of the same class now in print will show, at least, that it is an advance upon what has hitherto been accomplished. 1 shall be grateful, however, for further criticisms and suggestions; and I purpose at some future time to incorporate in a supplementary paper the results of such additional collections or corrections as I may obtain. To avoid too great prolixity, I adopted at the outset the following general principles: 1. To include the most important technical words and phrases used by American miners and metallurgists, or occurring in English books and periodicals.

Jan 1, 1881

By Harlowe Hardinge

AN extensive recent trip throughout the mining districts of the Southwest, Central West, an Northwest,' reveals a numbes of interesting conditions that have influenced operators, in both large and small mills, to modify their flow sheets insofar as they pertain to crushing and grinding. The changes made and planned for the future should be of interest. It is interesting to note when traveling through the country, how ideas change and practice is modified, and it is rather amusing to see how milling methods seem to run, more or less, in cycles. New ideas and developments are brought about which run through the industry and are taken up by many of the best and most well informed operators. Some of them will change, sooner or later, back to their old practice; for, like everything .else, what will work well in one place will not necessarily be suited to another. On the other hand, it is often difficult to establish. other practices known to be of value, owing to the natural resistance to make a change, but on the whole, the western mill men seem to be more alive to possible benefits of various modifications than any other engineers with whom I have come in contact in all parts of the world. Mill men in other parts of the world always keep in con- tact with what is being done in the western part of the United States, but it does not necessarily follow that those in the western part of the United States are always right. Some of these changes that have been made and afterward abandoned will be referred to later.

Jan 1, 1929

By S. Gstalder, J. Raynal

Consideration was given to simple tests which could be performed on rocks to give a measure of rock drillability. Various methods of breaking rocks were considered and the hardness test developed by Schreiner was selected for this study. The test involves application of an increasing load on the rock face through a flat-faced cylindrical punch until rupture occurs. Test results show that hardness is a good measure of the breaking strength of rocks. Useful relationships are shown to exist between hardness and other physical quantities such as specific disintegration, Young's modulus and sonic velocity. Specific disintegration (volume of rock broken per unit of work input) provides a possible means of comparing the effectiveness of other methods of rock breakage. The relationship between hardness and sonic velocity may be very significant for it may be possible to deduce rock drillability from sonic log data. provided that a mineralogical factor is taken into account. TO test further the results of the work, laboratory drilling tests were performed which closely simulated down-hole pressure conditions. Correlations of drilling results with rock hardness measurements were quite good. It was concluded that rock hardness, as measured in the laboratory or as deduced from sonic logs, could be used in relations for predicting rock drilling performance. INTRODUCTION Drillability of rocks cannot be defined in an absolute manner by a single quantity or measured by a single test. Resistance of rock to drilling depends to a large extent upon the means used for rock destruction. This complicates drillability classification of rocks for there may be as many classifications as there are methods of rock breakage without known functional relations between them. The objective of this work was to develop. in terms of rock destruction behavior, means of selecting the best drilling method for a given rock or the conditions for optimum output from a given drilling method. ANALYSIS OF ROCK DESTRUCTION TESTS Gauthier and Baron' have reviewed the many test methods which have been developed for determining the resistance of rocks to breakage. These include drilling tests, punch tests, scratch tests, resistance to shock, wear tests, etc. A standard drilling test might be to determine the time required to drill a standard depth (1/16 in.) in a rock using a bi-cone microbit (1 1/4-in. diameter) when a standard load (417 Ib) is applied at a standard speed of bit rotation (110 rpm). From the standpoint of similarity, the results of microbit drilling tests would seem to be most representative of the several methods suggested above. However, evaluation of drilling performance by this method is only qualitative and cannot be applied directly to actual drilling conditions. Punch tests basically measure rock hardness. Punches of various shapes and sizes, including small cones for Vickers' and Knoop's tests, the wedge for Epstein's test and the right circular cylinder for Schreiner's test, have been used. Results of these tests lead to a quantitative hardness classification which would seem to be related to the resistance of rock to bit-tooth penetration. Scratch tests are related to the resistance of rocks to abrasion such as would be encountered in drilling with diamonds. Either the width of the scratch obtained at a fixed load or the load required to give a scratch of a fixed width may be used to evaluate surface hardness of the rock. This should be related to the resistance of the rock to wear. The above tests, and probably many others. give relative measurements of the breakage or destruction characteristics of rocks. There is no direct relation between results of these tests and the drillability of rocks. Also, the tests each measure different quantities which have different dimensions and they do not permit direct comparison of numerical values. As one step in rectifying the above difficulties. it is proposed that the results of all test methods be expressed in terms of volume of rock destroyed per unit of work required; this is referred to as "specific disintegration". Test results may then be reported in a form which shows both a classification of rocks in regard to each method and a comparison of methods with regard to each rock. The disadvantage in using specific disintegration is the difficulty of measuring this quantity with accuracy. The volume of rock damage is difficult to measure. as is the true value of work input. Rock heterogeneity adds to the

Jan 1, 1967

By R. F. Lynch, J. D. Wood

The Al-1.0 pct Mg alloy 565 7 was studied using optical microscopy and electron microprobe X-ray analysis. Constituent particles were found to exist inter-dendritically in the as-cast material in a region of precipitate free a -aluminum. Five phases besides a fine precipitate and a-Al were identified in the cast structure: Fel3, Fe2Al7, Mg2Al3, CUMgAl2, and Cu2FeAl7. Thermal treatments conducted for 100 hr at 1180°, 1130°, 1080°, 1030°, 980°, and 880° F revealed a general dissolution and spheroidization of the in-terdendritic constituent network observed in the cast structure. The principal constituents present in the thermally treated structures were FeAl3 and Fe2Al7 with the relative amount of Fe2A17 to FeAl3 increasing with a decrease in the treatment temperature. The phases Present in the wrought structure were identical to those observed after the thermal treatments, with the constituent particles strung out in the direction of rolling. ALLOY 5657 is a nonheat-treatable commercial purity Al-1.0 pct Mg alloy utilized extensively because of its bright finishing characteristics. This investigation was conducted to determine the constituents present in 5657 alloy, and to study the effect of extended thermal treatments on morphology. Numerous studies have been carried out to establish the equilibrium diagrams for various aluminum systems,1-3 with phase identification based on X-ray analysis, morphology, and the etching response of relatively large particles. Phragmen4 conducted a study of the phases in aluminum eutectic systems and compiled a "corrected" table of etching responses, drawing on his work plus that of Schrader,5 Keller and Wilcox,6 and Mondolfo.7 A review of the original work of Keller and Wilcox, and Mondolfo, which was concerned with the constituents found in commercial alloys, reveals that in numerous cases their etching responses differ from those reported by Phragmen and from each other. These inconsistencies may occur because a specific constituent will react to a given etch in a varying manner depending upon its size, the elements dissolved in the phase, the other constituents surrounding a phase, and the solute content of the matrix. Work with a commercial orientation was conducted on alloys 2024 and 3003 by Sperry8,9 and on alloy 3003 by Barker,10 where the relationship between the phase diagram and the nonequilibrium structure of an alloy was examined. Backerud11 investigated the A1-Fe binary system and found that at high cooling rates the equilibrium eutectic reaction forming a-A1 and FeA13 is replaced by another lower temperature eutectic reaction forming a-A1 and metastable FeAl6, a constituent first identified by Hollingsworth et al.12 Most of the above mentioned studies were conducted on materials having a significantly greater alloy content than 5657 alloy, where the relatively small size and sparse distribution of second phase particles hinders the process of identifying constituents. EXPERIMENTAL PROCEDURE Material with a composition as given in Table I was examined in the as-direct chill cast, hot rolled and cold rolled conditions, and after thermal treatment of the cast structure. Thermal treatments were terminated by a water quench. Microscopic examination was conducted under various lighting conditions following the application of standard etchants as specified in Table 11. A semi-quantitative electron microprobe X-ray analysis was conducted for Al, Mg, Fe, Cu, Si, Zn, and Ti. RESULTS AND DISCUSSION Microstructure of the As-Cast Material. Particles of second phase material were found to exist inter-dendritically, principally in regions of precipitate free a-Al, as illustrated in Fig. 1. Adjacent to the ingot edge was a region of inverse segregation, resulting in an increased amount of second phase material containing large sized particles which aided in phase identification. Phase Identification. Cast Structure. Five phases besides a-Al and a fine precipitate were identified using optical microscopy and electron microprobe X-ray analysis, as presented in Tables II and III, respectively. FeA13 and Fe2A17 are often found with Fe2A17 forming a sheath around the core of FeAl3, resulting from an incomplete peritectoid reaction. These phases have a nearly identical appearance under white light, although they are easily differentiated under crossed polarizers, as characteristically illustrated in Figs. 2(a) and 2(b), respectively. Microprobe analysis con-

Jan 1, 1970

By A. J. Lena, M. F. Hawkes

Changes in hardness, tensile properties, microstructure, electrical resistance, and X-ray diffraction effects indicate that lattice strains are necessary for the embrittlement of ferritic stainless steels when heated for relatively short times at 475°C (885°F). It is suggested that 475°C (885°F) embrittlement is due to the accelerated formation of an intermediate stage in the formation of s under the influence of these strains. FERRITIC stainless steels (low carbon alloys of iron with more than 15 pct Cr) are subject to two forms of embrittlement when heated in the temperature range of 375° to 750°C. The embrittlement which occurs after long time heating between 565" and 750°C is well understood; it is caused by the precipitation of the hard, brittle s phase. Sigma is an intermetallic compound of approximate equi-atomic composition with an extended range of formation in Fe-Cr alloys. The maximum temperature at which this form of embrittlement can occur is dependent upon chromium content; and is approximately 620°C for a 17 pct Cr steel and 730°C for a 27 pct Cr steel. The other form of embrittlement occurs after relatively short heating periods in the range of 375" to 565°C; in the higher chromium steels, hours may be sufficient as compared to months for s embrittlement. This phenomenon is not at all well understood and several controversial theories have been proposed. The rate and intensity of embrittlement increase with increasing chromium content but the maximum rate occurs at 475°C re-gardless of chromium content. As a result of this, the phenomenon has been termed 475°C (885°F) embrittlement. The effect of 475°C embrittlement on the properties of ferritic stainless steels has been thoroughly reviewed by Heger.1 The embrittlement causes a pronounced decrease in room temperature impact strength and ductility, a large increase in hardness and tensile strength, and a decrease in electrical resistivity and corrosion resistance. Microstructural changes accompanying embrittlement are minor and difficult to interpret with a general grain darkening, appearance of a lamellar precipitate, grain boundary widening, and precipitation along ferrite veins having been reported at various times. With the exception of reported line broadening, X-ray diffraction studies by conventional Debye analysis of solid samples have been of little value. BY making use of electron diffraction methods, Fisher, Dulis, and Car-roll' have recently shown the existence of a chromi-um-rich, body-centered cubic phase in 27 pct Cr steels which had been aged at 482°C (900°F) for as long as four years. Two types of theories have been advanced to account for the embrittlement. The first of these requires the precipitation of a phase not inherent in the Fe-Cr system with various investigators suggesting a carbide,3 nitride,3 phosphide,4 or oxide." Theories of this type have difficulty accounting for the influence of alloying elements on the embrittlement and for the facts that a minimum chromium content is necessary for embrittlement and the intensity of embrittlement increases with increasing chromium content. The second type of theory that has been proposed relates 475°C embrittlement to s phase formation which is inherent in the Fe-Cr system. An assumption of this kind can adequately explain the influence of alloying elements, for they exert an effect on 475°C embrittlement similar to that on s phase for-mation as can be seen in Table I. The minimum chromium content is essentially the same for both phenomena and it has been shown12,13 that s is a stable phase in the embrittling temperature range. In addition, it has been reported14,15 that pure alloys embrittle to the same extent as commercial type alloys. There are, however, several factors which have prevented complete acceptance of a s phase theory. Foremost of these is that the embrittlement can be removed by reheating for short time periods above 600°C, which in the higher chromium steels is within the stable s region. No s has ever been observed after one of these curing treatments, nor has any s been found as a result of embrittlement at 475°C. In addition, the simple precipitation of s cannot explain the time-temperature relationships for reactions between 350°and 750°C. This behavior is shown schematically in Fig. 1. Newell 16 and Ried-rich and Loib4 have shown that 475°C embrittlement follows a C-type curve as illustrated, while Short-

Jan 1, 1955

By L. D. Jaffe, F. W. Cotter, E. Cordon

The hardenability of titanium-base alloys was studied by metallographic examination and hardness survey of Jominy specimens end-quenched from the B range. Analyses of the data led to the equation log J = -0.57 + 0.25 @ct Fe + pct Mn + pct Mo) + 0.19 @ct Cr) +0.16 @ct V) + 0.03 @ct Zr). Here J is the distance, in sixteenths of an inch, from the quenched end of a Jominy hardenability specimen in the position of peak hardness, for material quenched from the B range. This equation fitted the experimental data with a standard deviation of approximately 0.29. The effects of the elements Al, Sn, W, Cu, Ni, B, C, N, 0, and H, and of pain size, were not statistically significant or not practically significant. A check against hardenability measurements in the literature showed agreement within the stated standard deviation. The equation should be useful in estimating hardenability of new or modified titanium alloys. HARDENABILITY in a titanium-base alloy is the ability of the alloy to retain the B structure on quenching. An alloy with high hardenability will retain the /3 structure even when cooled relatively slowly from a temperature at which B or P plus a is stable. A low hardenability material will retain P only if quenched extremely rapidly from the range of p or 0-plus-a stability, or will not retain it at all, at room temperature. High hardenability is desirable in titanium alloys to be heat-treated to high-strength levels. Its value is by no means limited to large section sizes. With high hardenability, a material can be solution-treated and cooled at a variety of rates, either to give high strength directly or, more generally, to give a soft ductile condition from which high strength can be obtained by subsequent aging. With low hardenability, high strength can be obtained, if at all, only by very rapid quenching, and there will generally be little increase in hardness on subsequent aging; an alloy of this type is limited in its applicability. On the other hand, alloys of very low hardenability have some advantages in weldability; essentially, they are always in the annealed condition, after welding as well as before. For commercial alloys, hardenability data are usually available, in the form either of property data after cooling from the solution temperature at various rates, with or without subsequent aging, or of results of a standard hardenability test, such as that originally developed for steels by Jominy and Boegehold.' When modifications of an available alloy are considered, or preparation of new alloy compositions, it would be Very convenient to be able to estimate the hardenability of the new material without having to make and test it. A method of estimating hardenability of titanium alloys from their composition was suggested by one of the authors some time ago, on a preliminary basis, utilizing scattered data found in the literature.' It seemed worthwhile to carry out a systematic experimental study of the effect of composition upon hardenability. EXPERIMENTAL PROCEDURE Approximately fifty heats of various compositions, weighing 8 to 10 Ib apiece, were melted in a small inert-gas tungsten-arc furnace with water-cooled copper walls. The starting material was 110 Brine11 titanium sponge, with high-purity metals added for alloying. Each heat was bottom-poured under vacuum through a molybdenum burnout strip into a cold graphite mold, to form an ingot approximately 4-1/2 by 3-1/2 by 3 in.* From each ingot were cut *The material was melted and cast by Pitman-Dunn Laboratory, Frankford Arsenal, to whom the authors must express their thanks. two pieces 4-1/2 by 1-1/2 by 1-1/2 in. These were forged, at temperatures adjusted to the composition, into 1-1/4-in. rounds, from which standard 1-in.-diam hardenability specimens3 were machined. A number of small samples were also prepared from forged materials of each heat, annealed, quenched from various temperatures, and examined metallographically. The P-transus temperature was determined by observation of the degree of resolution of primary a in these pieces. samples for chemical analyses were also taken from the forgings. One hardenability specimen of each heat was solution-treated for 1 hr approximately 50°F above the measured transus temperature, and the other for 1 hr approximately 250°F above the transus. (An additional hour was allowed for the specimens to reach furnace temperature.) These are not necessarily the temperatures that would be selected for

Jan 1, 1964

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-' proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible 'References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961

One of the papers under this head covers the sampling and estimating of iron ores of the Lake Superior region as a whole while the other four papers cover the Gogebic, Marquette, and Menominee Ranges of Michigan and the Cuyuma Range of Minnesota.

Jan 1, 1925

PLANS are underway for the annual meeting of AIME, to be held in New York, February 17 to 21. The technical program includes meetings of all divisions of all three branches, Mining, Metals, and Petroleum. The bulk of the technical sessions will be held at the Statler Hotel, and the annual banquet will be held at the Waldorf-Astoria, Wednesday evening, February 20. The technical program of the Mining Branch activities is included in this issue. While it is not complete in every detail, it shows general interest groupings as well as subjects to be discussed. The program for each division is shown separately to facilitate following the activities of these special interest groups. Then, after a full scale and possibly somewhat strenuous technical meeting, a post-meeting feature will appeal to many of the members. A restful cruise to Bermuda and Nassau is offered at special rates to AIME members and friends. The schedule is a 3:00 pm departure from New York on the Queen of Bermuda on Saturday, February 23; arrival at Bermuda at 7:00 am Monday, February 25; arrival at Nassau at noon, Wednesday, February 27; and the trip ending again in New York at 9:00 am, Saturday, March 1. Rates begin at $202.10 per person, with higher rates depending upon accomodations desired. The base rate includes outside room with private bath and all meals, as well as Federal, Bermuda and Nassau taxes. Reservations for the trip should be made immediately through Leon V. Arnold, 36 Washington Square West, New York 11, who is in charge of arrangements.

Jan 1, 1952

By R. W. Raymond

The death of John Frederic Blandy, which occurred September 17, 1903, at Prescott, Arizona, terminated the earthly activity of one of the most active and able of the American mining engineers of the last generation. Mr. Blandy was born, April 24, 1833, at Newark, Delaware. His father was an Englishman, who had been in business in the island of Madeira, and had come thence to settle in the United States. At the age of eighteen, he was attached to the engineering field-corps of the Philadelphia & Reading Railroad; but, after a year of this service, he went to Germany, where he spent three years, entering in 1852 the Mining Academy at Freiberg, Saxony. Graduates of that institution need not be told that, at the period referred to, it held unique prominence in its special field, not only by reason of the great investigators and instructors, such as Cotta, Breithaupt, Weisbach, Plattner and Gaetschmann, who belonged to its faculty and brilliantly blended theory and practice in its work, but also because rival institutions were few. It cannot be fairly said that Freiberg has fallen below its ancient standard of excellence. Its chairs of instruction are still occupied by eminent men, worthy successors of the illustrious teachers who preceded them. But a host of technical academies, especially in this country, munificently equipped and efficiently conducted, have come into existence during the last half-century; and no one institution can ever hereafter claim the pre-eminence which the Freiberg Mining Academy once enjoyed. In those days, American mining engineers returning with satisfactory credentials from that school were sure of immediate employment.

Jan 1, 1904

By F. E. Crane, J. Downie

The general application of Darcy's law to natural rocks has already been challenged in the literature.1 The evidence shows that the permeability as calculated from the Darcy equation can be a function of the pressure drop and the salt concentration of the water phase. Most explanations for aberrant behavior involve clays and their properties and have been qualitatively satisfactory.Recently, however, Odeh2 revived the theoretical views of Yuster.3 Since Yuster's concept implies a fundamental error in using Darcy's relationship for two-phase flow, and not merely that conditions may limit its use, Odeh's experimental support arouses considerable interest. However, Odeh's work as presented is thought to to be inadequate. He has omitted important information about his materials and procedures; therefore, acceptance of his conclusions should be withheld. Since a clay effect is possible, Odeh should have been allowed space to present a more detailed account of the rocks which he used and the precautions which he took to avoid confounding the effects of clay and fluid circulation. In addition, it follows from Odeh's discussion that the oil relative permeability should increase as the viscosity ratio increases. Odeh presents data corroborating this deduction. It also follows that the oil relative permeability should decrease as the viscosity ratio of oil to water decreases. However, our results show that a high relative permeability, when once attained by using a viscous oil, may be maintained when that oil is replaced by an oil of much lower viscosity. EXPERIMENTAL PROCEDURE The results are shown in Fig. 1 and were obtained as follows. Sandstone cores. 3-in. long X l-in, in diameter and which contained clays, were saturated with

By S. C. Sun

This article by Spokes and Mitchell de- serves high commendation. For many years mineral dressers have been at a loss to explain the variation in magnetic susceptibility of the same mineral species obtained from different localities. In fact, they do not even have a list of accurately measured data on the specific magnetic susceptibility of weakly magnetic minerals to consult. Experience as a university teacher has firmly convinced me that the average student has more difficulty in acquiring a satisfactory knowledge of magnetism than of any other branch of mineral dressing. This is almost entirely because the subject has been treated far too much from a strict practical standpoint and far too little from a fundamental one. It is no exaggeration to state that almost all the published theoretical discussions are based on the experimental results of manufactured chemicals and alloys, but not of naturally occurring minerals. In an attempt to remedy this state of affairs, the author of this article not only set up a new magnetic balance in the Department of Mineral Preparation of The Pennsylvania State University, but also performed work of fundamental value, thus pointing the way to further research. This is evidenced by the fact that an investigation of the magnetic susceptibilities of manganese minerals was recently completed by S. G. Watt under the direction of David R. Mitchell, now acting dean of the College of Mineral Industries of the Pennsylvania State University. D. J. Cook is studying the magnetic susceptibility of titanium minerals under my supervision. It is hoped that our research program can be continued for several years and that similar investigations will be Initiated at other universities and research institutions.

Jan 4, 1958