Search Documents

By L. W. Kemph

The thermal expansion characteristics of aluminum alloys have been examined by several investigators, among whom may be mentioned Shakespear,' Schulz,2 Hidnert13 Hidnert and Sweeney4 and McCullough.' Shakespear compared the expansion of a series of aluminum alloys containing 14 per cent copper, with separate additions of about 1 per cent each of manganese, tin and zinc with that of pure copper. Schulz examined the expansion of aluminum and zinc and some aluminum-zinc alloys. Hidnert determined with a high degree of precision the exp:tnsion characteristics of pure aluminum, some aluminum-copper, aluminum-zinc, aluminum-silicon and some commercial alloys.' Hidnert and Sweeney examined the expansion characteristics of aluminum-beryllium alloys. McCullough, by an interferometer method, determined the expansivity of some aluminum-copper, aluminum-magnesium, aluminum-iron, aluminum-nickel, aluminum-silicon and aluminum-manganese alloys. Incidental to an investigation carried out during the past six years and leading to the development and exploit,ation of an aluminum piston alloy of relatively low thermal expansivity, the expansion characteristics of a wide variety of alloys were examined. Some of the data which might be of general interest are gathered in this paper. Experimental Procedure The apparatus used was essentially similar to those developed by the Bureau of Standards6 and Howard Scott,? with a few minor changes for expediency. The specimen was approximately 4 in. long and the differential length changes between specimen and the quartz tube were

Jan 1, 1933

By George Cole

WHILE many parts of Canada's pre-Cambrian shield are well served by railway, it is frequently necessary for prospecting purposes to proceed farther into areas in-accessible by rail. To such areas in summer the canoe was at one time the accepted means of travel for the prospector while the dog team was much used in winter. Al-though summer travel was much improved by the development of the outboard motor, the lack of facilities for cheap transporta-tion has been a serious hindrance to the employment of capital in opening up the distant fields. The pre-Cambrian surface of Manitoba, like that of Ontario, is hummocky, with rounded hills and ridges of rock alternating with basinlike depressions and valleys oc-cupied by lakes and rivers or by many low-lying portions covered with muskeg. Routes to the mines have not usually been direct or easy and seasonal vagaries have presented problems in themselves. In summer, water transportation may be the cheapest method for the longer dis-tances but it is not every water route that will satisfy the conditions of loading freight onto a boat or scow and of conveying it without interruption to its destination. By its location, a mine may require a large program of boat transportation in summer over part of its route, to be followed by winter freighting for the remainder. In order to carry on development and produc-

Jan 1, 1940

By Bruce W. Gonser, Robert J. Nekervis

EACH metal has a unique combination of properties that distinguishes it from other metal;. Su& a combination may account for applications that cannot be met very well by anything else. This is particularly true of tin, one of the earliest metals used by man. Table i shows the consumption of tin in the United States by usage for the years 1949 and 1950, which may be considered to be generally typical of current usage. The major applications-tinplate, solders, bronze, and babbitt-were well established a century ago. Applications for the metal and (probably later) of tin alloys started more than 5000 years ago. Fortunately for the ancients, tin is one of the metals whose oxide is easily reduced by carbon. Nature further simplified the refining problem by providing only one ore of commercial importance, cassiterite (SnO2). Tin is easily reduced from cassiterite. All that is necessary is high heat in the presence of carbon. It is quite possible that back in the dawn of history, tin was discovered when black alluvial sand was thrown on a fire, either to bank it or to put it out. SOURCES OF TIN All the important tin-producing centers are in the southern hemisphere, far away from the' industrial consuming centers. Fig 1 shows their location and 1950 production. Reserves are adequate, and the industry is able to produce considerably more tin than is

Jan 1, 1953

By R. A. Meussner, R. T. DeHoff, F. N. Rhines

ZINC diffuses through copper more rapidly than does tin. Accordingly, when a ternary diffusion couple is made, by bringing an 0 copper-zinc brass into contact with an a copper-tin bronze at fixed high temperature, it is to be expected that zinc will diffuse into the bronze faster than tin diffuses into the brass. Adjacent to the brass side of the couple the total alloy content (zinc plus tin) should diminish, therefore, while next to the bronze side the alloy content should increase. Since the path of compo- sition change must be continuous, in a single-phased alloy, it should follow a curved and, in general, an S-shaped course. The realization of this prediction is demonstrated in Fig. 1, where the composition paths of two ternary diffusion couples are plotted on the appropriate isotherm of the copper-tin-zinc phase diagram. The diffusion couples were both made from a binary copper-tin alloy analyzing 5.0 pct tin placed against binary copper-zinc alloys analyzing 18.9 and 29.3 pct Zn, respectively. These alloys were produced from electrolytic grades of copper and zinc and a pure grade of straits tin, melted under borax in clay-graphite crucibles and cast in a vertical iron mold. Cylindrical pieces 1 in. in diam and 1 % in. long were machined from the casting and were faced by metallographic polishing to good matching end surfaces. Pairs of the cylindrical pieces were held

Jan 1, 1959

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it-is felt that a description, of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By George F. Comstock

It has been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10 per cent. aluminum bronze, quenched for maximum hardness, and subsequcntly annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10 per cent. aluminum bronze at 400" C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature ' was necessary to obtain any softening effect. A later paper was by Seidell and Horvitz,2 who mentioned Portevin and Arnou's work, but did not report any increase in hardness obtained

Jan 1, 1925

By R. W. H. Acherson

Blast-furnace flue dust is one of the most troublesome operating factors in the iron and steel industry. It is usually involved in all the unpleasant phases of blast-furnace operations. It adds to our aggravations until we are willing to spend large sums of money to keep it out of our stoves and boilers and more money to handle it again and again on one scheme or another to induce the furnaces to retain it without bad after effects. Several successful operators claim that it is useless to recharge raw flue dust because the furnace would never have blown it out if it had been suitable material for blast-furnace consumption. Most of us who have made persistent efforts to return raw flue dust to the furnaces have decided that it is very often false economy to do so. Yet some remarkable results have been attained at the Ohio Works of the Carnegie Steel Co. through recharging raw dust. The plant comprises six modern blast furnaces. Up to 1909, about 300,000 tons of flue dust had accumulated in stock piles. During the last 10 years, there have been recharged into these furnaces all of the flue dust recovered from the furnace operations, the entire stock pile of Rue dust, and nearly 80,000 tons of dust shipped from other furnaces of the Carnegie Steel Co. The results obtained arc. shown in Table 1.

Jan 1, 1922

By H. J. French

WITHIN the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have. been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about ½ to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt, welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn.

Jan 9, 1919

By M. G. F. Söhnlein

IN THE metallurgical treatment of sulfide silver-tin ores mined at Oruro, Potosi, and Chocaya, the most important and difficult step is chloridizing-roasting. The ores are chiefly mined from veins in rhyolite, a detailed description of which can be found in most textbooks on ore deposits. The chief gangue minerals are Pyrite and quartz, and the silver content is derived from tetrahedrite, jamesonite, stibnite, and cylindrite. Most of the tin is present in the form of a rather impure cassiterite, which forms microcrystalline aggregates of varying richness with quartz and pyrite; occasionally, some tin is found as stannite, cylindrite, and other complex sulfantimonates. The silver content of the minerals that compose the ore is approximately as follows: Pyrite, 3 to 5 oz. per ton; jamesonite, 30 to 50 oz. per ton; stibnite, 30 to 150 oz. per ton; cylindrite, 200 to 300 oz. per-Jon; tetrahedrite, 500 to 3000 oz. per ton. Occasionally, some ruby silver ore is found, but it is very rare. In the mines of Oruro, which are the deepest in the sulfide zone, tetrahedrite has nearly disappeared, stibnite, jamesonite, and, in the deepest levels, cylindrite taking its place. At present, there are six mills treating this ore, two at Potosi, two at Chocaya, one at Poopo, and one at Machacamarca. The ore is crushed dry, given a chloridizing roast, leached with water and hyposulfite solution (or with brine) to extract gold, silver and copper, and concentrated for tin with or' without regrinding.

Jan 8, 1920

By Richard Miller

WORK was undertaken two years ago at the Hammond Laboratory for the purpose of determining the magnitude of the elastic range in single crystals of pure metals by means of creep tests, the assumption being made that if a true elastic range exists, the elastic limit represents the maximum stress for no creep. A sensitive extensometer was constructed, and creep tests were made on zinc single crystals at a variety of loads and temperatures1. It was soon discovered that there is tip measurable elastic limit in ductile zinc single crystals at, or above, room temperature. The inference that pure metallic single crystals may not possess a definite elastic range was not justified, however, since zinc had been tested in creep only above its recrystallization temperature, and several investiga-tors2,3,4 had already shown that above the recrystallization temperature polycrystalline metals will flow under very small stresses, while below that temperature stresses of a much larger magnitude are required. For that reason, it was decided to extend the study of the elastic limit to other metals having a higher recrystallization temperature than zinc. Aluminum and silver were selected, because of the ease of obtaining pure materials and of preparing large single crystals, and because the crystallo-graphic glide system of these metals is well known. Owing to the limited time available, the elastic range was investigated by slow tensile tests rather than by creep tests.

Jan 1, 1937

By John Garcia

IN some districts of the bituminous coal field the problem of construct-ing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large. Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton acid Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, 111. All three have water conditions that make it necessary to regularly seal off till worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. As far as the writers know, these three mines are the only ones in the bitu-minous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will he included herein on the Saxton mine than on the others, as the writers are more familiar with it.

Jan 1, 1937

By George W. Neumann

The mines and concentrator of Brunswick Mining and Smelting Corporation are located in the northern part of the province of New Brunswick, approximately 20 miles distant from the City of Bathurst. Discovery of the No. 6 orebody by diamond drilling in 1952 was followed by the finding in March 1953, of the larger and higher- grade No. 12 orebody, approximately six miles to the north of the No. 6 deposit. Original development was financed by St. Joseph Lead Co., and included a small open-pit operation with a 10C ton per day pilot mill at No. 6 orebody, shaft sinking and underground development at No. 1; orebody, and an extensive program of laboratory and pilot plant metallurgical research on No. 12 ore. These operations were suspended in May 1958, and remained in standby condition until June 1961, when the equity of St. Joseph Lead Co. was purchased by a group headed by M. J. Boylen, K. C. Irving, Maritime Mining Corporation, and the Patino Corporation. Construction of a mine plant and concentrator at the No. 12 mine commenced in October 1962 and the concentrator was placed in operation in March, 1961b. Preparation of the open pit mine for production, construction of the No. 6 Concentrator to produce bulk Pb-Zn-Cu-Ag concentrate from No. 6 ore, and construction of an Imperial Smelting Process smelter at Belledune were started in 1964 and placed in operation in September 1966.

Jan 1, 1970

By Jasper Stuckey

THE object of this paper is to record and interpret field and laboratory observations made by the writers during five years of study of the barite deposits of North Carolina. Deposits of barite are known to occur in three localities in North Carolina (Fig. 1) two of which-the Hot Springs and Kings Mountain -contain material of economic value. The Hot Springs area begins near Bluff, some 6 miles south of Hot Springs, and continues northeast by Stackhouse; a total length of 7 miles. The Kings Mountain deposits lie along a belt that extends from the north end of Crowders Mountain in a southwestward direction, along the east side of this and Kings Mountain, to Kings Creek, South Carolina. The third locality is 3 1/2 miles southeast of Hillsboro, Orange County, a short distance west of the highway leading from Hillsboro to Chapel Hill. It is not known when barite was first discovered in North Carolina, but production from the Hot Springs area began some 50 years ago. The state has never produced large quantities of barite-usually there have been less than three producers-and definite figures are not available, but reasonably reliable estimates indicate a total production of 300,000 tons. From 1901 through 1920 barite mining was on a seemingly prosperous basis and a large tonnage. was shipped from the Hot Springs and Kings Mountain areas. With the depression of 1920 the industry began to decline and production practically ceased in 1926.

Jan 1, 1933

By Norman Weiss

IF we were to measure progress this year in terms of large new mills and discoveries of fundamental significance we should certainly be disappointed. Outside of the uranium field there was little of a spectacular nature. San Manuel and Reserve completed their first year of operation; Erie approached readiness; the Toquepala project in southern Peru broke ground and gained speed. Important mill enlargements occurred at Inspiration, Anaconda, Ray, and Climax Molybdenum. A 3000-ton copper concentrator was completed at Pima, near Tucson. The Republic Mill of Marquette Iron Mining Co. started up in April. Abroad, the great developments in the African Copper Belt can be likened to the rapid growth of the porphyry coppers in this country. Fundamental research was confined nearly entirely to iron ore flotation and recovery of metal values from leach solutions, particularly uranium. The large number of review articles this year reflected a desire to take stock and consolidate past gains before taking the next bold steps. Undoubtedly a shortage of competent young engineers and technicians is stunting the natural growth of theoretical investigation in the field of minerals beneficiation, as well as the conversion of ideas into action. We find our small stock of talented young scientists concentrated in a few centers of erudition because there are not enough to diffuse through the industry. It is safe to say that among mine administrators and managers there is more interest in the education, training, and welfare of the young engineer than ever before.

Jan 2, 1957

By D. G. F. Hedley, S. N. Muppalaneni, J. W. Roxburgh

A stope and pillar method is used to mine the gently-dipping uranium bearing reefs, to a depth of 1000 m, at Elliot Lake, Ontario. A few isolated rockbursts have been reported in the 11 mines in the area during the first twenty-five years of operation. However, in March 1982 a series of rockbursts were initiated in the old mined-out workings at the Quirke Mine of Rio Algom Ltd. Detailed records of pillar deterioration and size of the affected area were kept both prior and subsequent to the occurrence. Seismic instrumentation was installed before and convergence stations shortly after the start of bursting. Observations indicate that the squat pillars failed violently where- as the slender pillars exhibit a less violent failure mechanism. Floor cracks and heaving are common, but the massive quartzite hanging wall strata is relatively undamaged although some roof falls have occurred due to local structure. The microseismic system accurately locates seismic events to f 20 m within the geophone array and it has been found that an accelerating convergence rate coincides with and in some cases precedes an increase in seismic activity. Displacement discontinuity and boundary element computer models have been used to estimate pillar stresses and areas of high stress concentration in an effort to determine the causes of rockbursts. Mine and pillar stiffness and energy balance concepts are used to explain cases of gradual and sudden pillar failures at Quirke Mine.

Jan 1, 1984

By A. W. Gray

Page CRUSHING STRENGTH...................... 659 The Black Dynamometer....................659 A Standardized Procedure for Crushing Strength Tests...... 660 Influence of Height of Test-piece upon Apparent Strength ..... 662 Influence of Packing Pressure and of Packing Time........ 662 Application of the Logarithmic Law...............665 Influence of Amalgamation Variables.............. 665 Influence of Temperature................... 669 The Transition Region Near 70" C............... 671 Influence of Packing Pressure at Various Temperatures ...... 673 Influence of Age upon Alloy and Amalgam........... 676 DIMENSIONAL CHANGES DURING THE HARDENING OF AN AMALGAM .......................... 678 The Black Amalgam Micrometer............... 678 Thermostated Dilatometer Designed by the Author........ 681 Graphical Representation of Reaction Expansions......... 683 The Typical Reaction Expansion Curve ............. 684 Influence of Packing Pressure................. 686 Influence of Trituration Time................. 687 Influence of Temperature................... 688 Influence of Mercury-alloy Ratio................ 689 Influence of Packing Time................... 689 Influence of Annealing the Alloy................ 691 Influence of Size of Alloy Particles...............691 Extension of the Typical Expansion Curve........... 693 Influence of Thermal Softening and of Reamalgamating a Hardened Amalgam.......................... 634 Curves Obtained with a Variety of Dental Alloys ........ 694 Copper Amalgam ...................... 694 PRACTICAL APPLICATIONS OF THE RESULTS.......... 695 Phenomena which reveal chemical and physical processes that probably go on in many alloys at temperatures not far removed from their melting ranges are observable in dental amalgams. These amalgams should. therefore. be of even more interest to the metallographer, the metallurgistl the chemist. and the physicist than to the dentist who uses them for saving decaying teeth. For this reason I am here de-

Jan 1, 1919

By Harold Roast

THE object of this investigation was to compare the arsenical antimony-lead alloy with some of the regular bearing-metal alloys. With this end in view, the following tests were made: 1. Chemical analyses to show the composition. 2. Thermal analyses. 3. Macroscopic examination of fractures. 4. Microscopic examination. 5. Tensile tests. 6. Crushing tests. 7. Scleroscope tests. 8. Brinell tests, at temperatures from 80° to 400° F. Tests 3 to 8 were conducted on both sand-cast and chill-cast specimens. For the purposes of this paper the alloys have been numbered from 1 to 6; their composition is as follows: LEAD, ANTIMONY, TIN, COPPER, ARSENIC, NUMBER PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. 1 82.64 12.95 4.40 0.01 none 2 27.54 9.94 59.87 2.65 none 3 77.65 20.75 none 0.13 1.47 4 82.95 16.85 none 0.20 none 5 83.78 15.35 none 0.05 0.82 6 0.15 7.87 84.13 7.85 none The analysis, in the case of the antimony, was made by solution in sulfuric acid and titrated with permanganate. For tin, the ferric-chloride method was used; for copper, the alkaline separations, and the thiocyanate methods; for arsenic, volatilization of arsenic and titration with iodine. The lead, with the exception of alloy 6, was taken by difference.

Jan 2, 1922

By Maurice Cook

A procedure of obtaining specimens of lead, tin, and cadmium with a moderately equiaxed structure and a smooth surface suitable for etching without grinding and polishing is described; the advantages of general oblique illumination (as opposed to vertical illumination) in the photomicrography of pure metals .are stated. Using these methods, a statistical study of the changes brought about in deformed lead, on annealing, has been made. The common mode of structural change was found to be recrystallization. Cases of growth of one original grain into another were rare; but if a totally recrystallized specimen was annealed above 200° C., a few large grains appeared and spread over the whole area, except for a certain number of small grains which remain unabsorbed. The temperature needed to produce structural change in lead was found to be lower, the greater the degree of deformation. With tin, an extension of 28 per cent. caused practically no recrystallization at ordinary temperatures, but recrystallization occurred if the specimen was heated to 100° C. In cadmium at low temperatures, the grain size decreased in marked manner as the deformation increased; but at high annealing temperatures, the grain size was comparatively independent of the degree of deformation. THE structural changes in metals brought about by annealing following a deformation at a low temperature has been the subject of many investigations. No less than eleven metals and alloys have been studied in some detail; namely, aluminum,1 tungsten,2 iron,3 copper,4 gold,5

Jan 11, 1924

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940