Search Documents

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By Walter Rosenhain

In selecting solid solutions for the subject of this lecture I have been guided by several considerations. The bodies known under that somewhat paradoxical name play a most important part in all types of alloys; consequently, a deeper knowledge of their constitution must 'be of fundamental importance to both metallurgical science and practice. Further, having been asked to deal with some of the more theoretical aspects of metallurgy, I have been tempted to describe certain considerations, which I believe to be novel, in regard to the nature of solid solutions. These considerations constitute a theory that requires much experimental confirmation, but they have passed the stage of speculations, for experimental evidence has become available and one inference after another, that can be derived from the theory, is found to be in accord with well-known facts. In putting before you these ideas and inferences, it must be understood that detailed quantitative proof of every step cannot be furnished. Our conclusions must therefore be stated with the reservation that their acceptance must depend on the manner in which the discovery of fresh facts may either confirm or confound them. If we wish to understand the structure of solid solutions we nust carefully realize the manner in which these bodies are formed in alloys. The formation of solid solutions is by no means confined to alloys, but it is desirable to confin5 attention, at the outset, to intermetallic solid solutions. It is not easy to formulate a precise definition of the term "solid solution." It may be said that a solid solution is a crystalline body formed from a liquid solution or from an intimate mixture of solids, or of liquid and solid, that retains in the solid state an admixture of the two substances (solvent and solute) as intimate as that which exists in a liquid solution. The term is undoubtedly paradoxical, for one usually associates solution with a liquid, but the difficulty cannot be evaded by using such a term as solidified solution, for this might refer to a solution that has set, or congealed, without undergoing crystallization. The German term mischkry stall avoids the difficulty and appears to

Jan 1, 1923

By C. Richards Honeycutt, Frederick C. Langenberg, Guenter Pestel

Solidification in a moving electromagnetic field was successful in altering the as-cast grain structure of steel ingots. The equipment is described and exerimental results are presented for several different alloys. Conditions for optimum grain refinement are described and an empirical design constant presented. The effect of the grain refinement on hot workability is briefly discussed. T HE grain structure of a steel ingot teemed into a metal mold can be defined by macroscopic examination in semiquantitative terms. For example, the relative volume of obviously differing structures can be estimated with the classic definitions of chill, columnar, and equiaxed zones. Experimental evidence has proven that the grain structure of an ingot is affected by changes in such factors as teeming temperature, rate of teeming, degree of turbulence, size of ingot, mold characteristics (including preheat temperature, design and coating), and composition of the metal (especially as it affects the range of solidification). Significant advances have been made in fundamental solidification studies; but the principles which have been developed are difficult to apply tothe complex and changing phenomena that occur simultaneously during ingot solidification. In particular, many attempts have been made to refine the as-cast structure of ingots, with special emphasis on the columnar grains. The formation of large columnar grains is generally considered harmful to the further fabrication of an ingot. It may also result in undesired ani-sotropic properties. However, columnar grains are not undesirable in all grades, or product applications, and caution must be exercised to determine in which grades and applications columnar grains are not desired in the ingot. Although the literature on the refinement of as-cast ingot grain structures is too vast in general to review here, it is noteworthy that such methods are additions of artificial nuclei, mold vibration, mechanical stirring or ultrasonic agitation of the molten metal, and controlled cooling and reheating during solidification have been tried with varying degrees of success. However, it is doubtful that any method of refining the as-cast ingot grain structure has been completely successful on a commercial basis. The purpose of

Jan 1, 1962

By J. R. Mihalisin

Phase changes in as-cast alloys in the Ni2 CoCr-Ni, Ti-NSAl system containing 0.1 wt pct C were studied after heat treatment at 1650°F. It was found that a vegion of CrCo-type s was developed in this system after I1000 hr. The tendency for s formation was dePendent upon the aluminum and litanium content, the s -forming tendency generally becoming more pro-nounced as the latter two elements are increased. s lended to form in interdendritic regioues and was associated with solutioning- of- carbide phases. Electron- vacancy computations for prediction of s formation on these alloys mere in sufficient agreement with what was observed experimentally to indicate that the method should be of value in assessing a-forming potential in cast alloys. However, the correlation of electrotz- vacancy numbers may not be as favorable in cast as cormpared to wrought alloys. THE increasing use of high-temperature alloys for longer times at higher temperatures has resulted in a real need for obtaining information on the phase changes taking place in these alloys since these changes often have a direct effect on properties. This paper reports on a study of the phase changes in Ni-Cr-Co-Al-Ti alloys after prolonged heating at 1650°F. The alloys were selected from the pseudo-ternary system Ni2CoCr-Ni3Ti-Ni3Al and this system was chosen because it is the basis of many of the newer cast commercial superalloys. The attempt here was not to define accurately the boundaries of s formation in the NizCoCr-Ni3Ti-Ni3Al system but to delineate the phase transformations taking place upon heating alloys covering a wide range of chemistries in this system. An addition of carbon was made to all alloys to further simulate commercial alloys. It was hoped that the information generated in this manner would be of more direct use to superalloy designers than an equilibrium diagram approach since commercial alloys generally have outlived their usefulness when equilibrium is attained. EXPERIMENTAL PROCEDURE The alloys were vacuum-melted from carbonyl-nickel pellet, vacuum-grade chromium, electrolytic cobalt, high-purity aluminum and titanium, and spec-trographic-grade carbon.

Jan 1, 1968

By F. V. Lenel

R. P. Seelig.*—Dr. Lenel is to be congratulated on his presentation of a particularly interesting paper describing the use of the powder metallurgy process for the production of magnetic pole pieces. The only thing that might be added is that we have been successful in producing pole . pieces with a narrow hysteresis curve by the use of considerably lower sintering temperatures than the ones used by Dr. Lenel. It is quite possible that this use of lowe- temperatures has considerably widened the field of commercial application for pole pieces made from metal powders. Development work is currently being done on an a.c. application of a sintered iron part. However, I am in full agreement with Dr. Lenel that if eddy currents are an important factor in the application, we cannot substitute sintered material for laminated sheet-metal structures. Mr. Peters' remarks concerning the limitations of machine parts were well taken. The emphasis of the limitations makes it easier to define clearly what we can do and-what the advantages are of machine parts made of metal powders. When I mention metal-powder machine parts, I mean those of relatively high density, although complete elimination of porosity is not possible at this time. The limitations of the field for this type of parts are largely economical. I believe that Mr. Langhammer has made that point very clear. The following questions are very often asked: How large a part can you make? How close can you hold the dimensions ? How fast can a part be produced? In a majority of the cases, it depends on the cost at which the part can be produced. A large variety of shapes and sizes of a number of materials can be formed. However, the main requirement in this field of endeavor is whether this can be done more economically by powder metallurgy than by other manufacturing methods. As a general indication, it may be stated that densities up to 95 per cent of that of rolled material can now be produced commercially in simpler parts. Tolerances of plus or minus 0.001 in. are common, but where special conditions justify, closer tolerances can be held; we are producing a part of which one dimension is held to 0.0003 inch. Finally, as far as maximum size is concerned, technically this would depend on the capacity of the press and furnace equipment available. Actually, we find that the economical limit of powder-metallurgy machine parts is approximately one pound. From there on, each individual case must he studied on its own merits.

Jan 1, 1945

By S. G. Valentine

BLAST-FURNACE blowing engines are broadly of two main types: either steam- or gas-driven reciprocating engines, or turbine-driven rotary engines. Some results of experience with a furnace blown by an engine of the latter type may be of sufficient general interest to relate. The first engine of this type was installed at Oxford Furnace, New Jersey, before the writer's connection with this plant, in March, 1910. This furnace uses chiefly New Jersey magnetites and had been in blast seven months on its old engines when the turbo blower was started. It was 80 ft. high by 17 ft. 6 in. bosh and 11 ft. hearth diameter. It is of interest to see from the records what happened when the turbo engine was put to work. But of course, as the old blowing equipment was rather antiquated, consisting of two I. P. Morris engines with air cylinders 72 by 72 in., in good running order, however, it is evident that the comparison between their work and that of the turbo blower cannot be interpreted as being between machines that were respectively of equal excellence as representatives of their types. Still the results were gratifying and -interesting. The records show that, with the old engines blowing 13,630 cu. ft: of air per minute, measured by piston displacement, the furnace was working up about 480 tons of stock per 24 hr. and producing an average of 132 tons per day and a maximum of 166 tons. The rotary blowing engine installed was a General Electric Co. machine, the driving end being a Curtis steam turbine and the air end a six-stage rotary compressor, all running at about 1,500 to 1,600 rev. per minute, and having a capacity of 25,000 cu. ft. of air per minute up to 25 lb. pressure, and equipped with an automatic constant-volume variable-speed governor. After running this blower, for a period equal to that covered above by the old engines, at an average rate of 15,000 cu. ft. of air per minute, the furnace worked up an average of about 592 tons of material and produced an average of 170 tons per day. Thus, on an apparent increase of 10 per cent. in the air volume there was an increase of about 23.5 per cent. in the materials worked up and of about 28.8 per cent. in the product. For the first calendar month's operation of the turbo blower, on an average of 15,040 cu. ft of air per minute, there is

Jan 2, 1914

James Douglas will long be remembered as a distinguished mining engineer and metallurgist, as a scientist with broad vision, as an executive whose understanding of practical problems coupled with his knowledge of men and affairs enabled him to weld together great mining interests and to their service build railroads and bring power. More, he will be recalled as a philosopher and a writer of charm, a historian of no mean order, and one whose catholic tastes and enthusiasms led him into the fields of education, medicine and theology. His aim was to possess that which he considered made life worth while—friends and effectiveness in whatever task he undertook. In this aim he was successful to a degree exceeded by few, as thousands of his friends and associates could and can testify. Dr. Douglas was born on November 4,1837, at Quebec, Canada. His father, James Douglas, Sr., was a prominent physician and the leading surgeon of Canada. He also established the first retreat for the insane in the Dominion, the Quebec Lunatic Asylum, to which he devoted his services for years; The son followed in the footsteps of his father and studied medicine, not only in Canada but also in Scotland and in Germany. He entered the University of Edinburgh in 1855 but after two years at that institution returned to Canada and was graduated from Queens university at Kingston, Ontario, .with the degree of Bachelor of Arts. Later he went to Lava1 University, Quebec, and subsequently became professor of chemistry at Morrin College, Quebec. After he was graduated—at the time he considered his formal education completed—he traveled with his father in Europe and in the Orient; visiting Egypt, being especially interested in that country, several times. They gathered together an important archaeological collection which later was donated by them to the Metropolitan Museum of Art in the city of New York. James Douglas was also greatly interested in photography, a hobby in which he made use of his chemical knowledge. The writer can remember distinctly the descriptions he gave more than forty years ago in Arizona of the difficulties he encountered with the old wet photographic plates, especially while traveling in Egypt, when he prepared and used his own chemicals. In his humorous manner he told how he once discovered, in the nick of time, the nurse preparing to give the baby in the party a rub-down, using for that purpose the white, limpid

Jan 1, 1934

By D. R. Miller

Internal friction and elastic modulus variations in electrorefined titanium, iodide refined titanium, and alloys of the latter material with oxygen, nitrogen, aluminum, and zirconium were investigated. No oxygen peak was detected with electrorefined titanium but, provided precautions were taken to prevent increases in background damping, an oxygen peak at about 410°C could be resolved with each of the other materials. An additional partially resolved peak was observed at 500°C in a Ti-N alloy. An anomaly in the variation of rigidity modulus with temperature was observed. Possible mechanisms for the formation of any oxygen peak have been discussed. PRATT, Bratina, and Chalmersl investigated the internal friction of commercial purity titanium and alloys of this material containing 1.5, 3.5, and 4.5 at. pct O. With commercial titanium the internal friction curve consisted of two components, a background which increased steadily with temperature and a peak at about 600" C which was due to grain boundary relaxation. In the Ti-O alloys, however, an additional internal friction peak was observed at 430" to 450°C and, since this peak increased in height as the oxygen content was increased, it was thought to be associated with the presence of oxygen. The diffusion of oxygen in titanium at temperatures between 300" and 500° C is believed to have marked effects in its tensile properties2'3 and the present internal friction measurements were undertaken to obtain further information on this diffusion, using material of higher purity than that of Pratt et d. and an apparatus of very much greater sensitivity. In the course of the investigation a number of important limitations on the work of Pratt et al. were revealed and results have been obtained which emphasize the need for ensuring that in this type of experiment, internal friction is independent of strain amplitude and that the values obtained are reproducible. 1) MATERIALS AND APPARATUS The basis material from which the majority of the specimens was prepared was iodide-refined titanium, the major impurities in which were oxygen and nitrogen—the metallic impurities being present at concentrations less than 0.001 at. pct. The hardness of this material after arc melting, forging, and swaging to rods 1/4 in. diameter was Dph = 110. Specimens 10 in. long and 0.020 in. (0.51 mm) diameter were prepared from these rods by further swaging and wire drawing and were finally annealed in vacuo (5 x 10-6 mmHg) for 24 hr at 800°C. The oxygen alloys were prepared from iodide-

Jan 1, 1962

Joseph Esrey Johnson, Jr., had already achieved rare distinction as an able metallurgist, clear thinker, brilliant author, and wise consulting engineer to bankers and operators; he had achieved the essentials of a great career when dcath cut short his activities on Apr. 4, 1919, in the forty-ninth year of his age. He belonged to a family of iron blast-furnace men and mine managers. His father, Major J. E. Johnson, after serving with distinction in the Army of the North, identified himself with the iron mines and blast furnace at Longdale, Va., with which he was connected during almost his entire business life. It is significant, that, during those troublous times of reconstruction in the South, he enjoyed always the affection and respect of his neighbors and associates alike. From him his son obtained not only a thorough training in blast-furnace practice and iron mining, but great personal courage and force of character. His mother, who survives both her husband and sons, possesses rare intellectuality, humor and a tenderness and human sympathy which those who were privileged to know well J. E. Johnson, Jr., recognized beneath his exterior of aggressiveness and will power. In a recently published analysis of the qualities which characterize the world's great men, three traits stand out preeminently; viz., independence, courage, and intellectuality. Each of these characteristics J. E. Johnson, Jr., possessed in extraordinary degree. His early education was obtained under a private tutor at Longdale, and this circumstance probably enhanced a natural tendency to independence of character and individuality which, however, under the control of his unusual power of straight thinking and clear analysis never allowed him to go far astray. It has been said of him that if once he set his mind to a problem, however knotty, he scored a bull's-eye before the subject was dropped. His manner of attacking a subject involved first mastering the details of the available knowledge; then, putting this acquired information to one side, with an untrammeled mind blazing out a path of his own, so clear, so well-defined, and expressed in such simple terms that he illuminated the whole subject without distorting the original data or discussion. His two books, "Blast-furnace Construction in America" and "The Principles, Operation, and Products of the Blast Furnace, "on the iron blast furnace together form the most comprehensive, the most enlightening, and the most useful treatise on the subject ever produced in any language. But his ability did not end with the mastery and elucidation of principles enunciated by his predecessors; his own

Jan 1, 1920

By John T. Thorndyke

MOST important of the naturalcalcium silicates is the meta¬silicate, CaSi03, known as wollastonite, after W. H. Wollaston. A large deposit of this mineral was dis¬covered some seven years ago near Code Siding, Rademacher mining dis¬trict, Kern County, Calif., the deposit being some 7500 ft. long and of an average width of 300 ft. It consists of a series of small domes striking north¬erly and southerly and with a dip of 81 ° to the south. This deposit was opened up by a series of small quarries showing a potential tonnage of 12,000,¬000 tons, allowing of cheap mining and transportation, the Southern Pa¬cific R.R. spur track being one mile north of the workings. Numerous sam¬ples taken from different points on the deposit, tested by Mr. Brinker, of the California Testing Laboratories, Los Angeles, showed an average as fol¬lows: Per Cent Silica (SiO2) 47.12 Lime (CaO) 41.72 Magnesia (MgO) 2.72 Alkalies (R,0) Trace Iron (Fe.,O,) 1.60 whereas the theoretical composition of of wollastonite, as given by William Shirley Bayley, is as follows: Silica 51.75 Lime 45.25 The tonnage and purity of this de¬posit led to investigations into its com¬mercial development. Early work es¬tablished the fact that wollastonite was ideal for the manufacture of a tough, almost unbreakable, glass similar to Pyrex. It also established the fact that wollastonite was particularly adapted for use in the manufacture of mineral wool, towards which further research was then directed. Briefly, the prin¬cipal advantages were the substantially unvarying chemical composition of the naturally occurring mineral and its characteristic of being relatively flexi¬ble and highly resilient when fused into a glass. A mineral wool produced therefrom is thus not only of highly uniform composition and color but is most desirable because of the high mechanical strength and length of the individual fibers constituting the wool. It is well known that mineral wool may be prepared by melting a suitable charge of raw material and then intro¬ducing a stream of a suitable fluid, such as air or steam, into a stream of the molten raw material. By this means the molten material is blown into threads or fibers, which are collected in a suitable chamber similar to a tun¬nel, from which they are removed from time to time or continuously. Com¬mercial manufacture of mineral wool has been carried on for only about 50 years, but volcanoes, specifically Kilauea in the Hawaiian Islands, have

Jan 1, 1936

By George Fancher, R. L. Whitting

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By R. L. Whitting, George Fancher

A typical drilling mud from the Hastings oil field, Brazoria County, Texas, containing only 8 per cent (dry basis) of material of colloidal dimensions, which is largely illite, was concentrated to a density of 10.2 lb. per gal. and used in this study. The effects of water dilution, treatment with complex polyphos-phates, temperature and the time of heating upon the rheological properties of the mud were investigated. It was found that water plays an important part in chemical treatment and that sodium acid pyrophosphate and sodium tripolyphosphate were more efficient than other complex polyphosphates for chemical treatment. Muds treated with either of these chemicals manifested maximum reduction in viscosity and minimum filtration rates at low concentrations. Furthermore, .mud treated to minimum viscosity with either of these two chemicals was virtually unaffected by heat-treatment. Introduction The drilling of deep wells is dependent upon the use of drilling mud, and problems frequently arise concerning the effects on mud of temperature, prolonged heating and aging. The use of chemicals to control the rheological properties of mud is a well-established practice. Salts of weak organic acids such as sodium tannate or gallate were used at first until the complex phosphates of sodium were found to be more efficient. Consequently, it seemed important to investigate the reaction of a mud to chemical treatment with phosphates, temperature, heat-treatment and aging, particularly since previous work in the laboratory at the University of Texas had provided the particle-size distribution and mineral composition of Hastings mud. Properties or Mud Used in Experiments A large sample of the mud from a drilling well in the Hastings field, Brazoria County, Texas, was obtained directly from the circulatory system. Some of the general physical characteristics of the mud and other data are presented in Table I. Table i.—General Properties of Hustings Drilling Mud Alex- Cur-ander keet Well Well Depth when sample was taken, It.. 5720 5700 Weight. lb. per gal............... 9.5 0.8 Viscosity, sec. A.P.I.............. 47 60 Viscosity, Stormer, grams......... 80 Viscosity, centipoises............. 13 Filtration rate, c.c. per 30 min.a. . . 19.6 22.8 Salt content (chlorides), per cent... 0.13 0.12 pH............................. 8.9 8.9 The Alexander mud was used for the experimental work. Comparison with Curkeet mud indicates a considerably greater dilution but otherwise suggests similarity. The mineral composition and particle-size distribution of Curkeet mud (Table 2) are available (Fancher and Oliphant6). It is suggested that Alexander mud would have a similar composition.

Jan 1, 1943

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

IN 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group -SO4- or _S03- are excellent collectors for cassiterite and promise to be selective.1 The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000gram Denver cell. EXPERIMENTAL METHODS Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously described.5-10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these tests determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver Submachines.--Melbourne tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By Akio Suzuki, P. G. Wahlbeck

AS a part of a study of the vaporization of transition metal-chalcogen systems, the vaporization reactions for the Ti-Se system have been studied. In order to establish vaporization reactions it is important to determine the identity of vapor species in equilibrium with the condensed phases. In some cases, it is possible to deduce the identity of vapor species through observations of composition change of the condensed phase with which the vapor is in equilibrium. Determination of vapor species in equilibrium with condensed phases should precede vapor-pressure measurements and is necessary for proper thermodynamic analysis of vapor-pressure data. Bear and McTag-gart' reported that vacuum heating ot TiSea at 950°C produced a residue with a composition of 1.7 Se/Ti atomic ratio units. Analyses of condensed phases existing for the Ti-Se system have been performed by Bernusset,2"4 Gron-vold and Langmyhr,5 Hahn and Ness,' and Ehrlich.~ Results and conclusions of two types of experiments are described herein: 1) experiments where samples of known composition were vaporized followed by chemical analysis of residues and 2) experiments where the vapor species were identified by means of a mass spectrometer. Experimental Section. Sarnple Preparation. Samples of TiSe2 were prepared in a sealed, evacuated quartz ampule by heating to 1000°C stoichiometric amounts of selenium of 99.999+ pct purity obtained from the American Smelting and Refining Co. and titanium of 99.2 pct purity obtained from A. D. Mackay, Inc. After heating, the sample was ground and reheated to insure homogeneity. Samples containing less selenium than TiSez were prepared by mixing amounts of titanium powder and TiSez appropriate for the desired composition; the titanium and TiSez mixture was heated in the same manner as described for TiSe2. Analyses of titanium selenide samples contained in quartz crucibles were performed by gravimetric oxidation in oxygen at 800°C; the products of the oxidation were solid TiOz and gaseous Se02. The mass of the original sample and the mass of TiOn determined the Se/Ti atomic ratio. The sample of TiSen used in these experiments had a composition of 2.04 Se/Ti atomic ratio units. The compositions for all samples reported were analyzed by this method. Va/!orization Experiments. Samples of titanium selenides were vaporized in tungsten Knudsen crucibles. Some vaporization experiments were carried out in glass vacuum lines followed by chemical analyses of residues, and some vaporization experiments were performed with a Bendjx mass spectrometer as described previously.8

Jan 1, 1967

By C. E. Nelson, T. E. Leontis

THE properties and casting characteristics of sand-cast Mg-Al-Zn alloys, used commercially in this country and abroad, have been discussed in a number of articles during the past few years.'-" In addition, broad surveys of many compositions in the magnesium corner of the Mg-Al-Zn diagram between 0 and 12 pct A1 and 0 and 6 pct Zn have been presented by Busk and Marande7 and by Fox." The purpose of this paper is to furnish a comprehensive survey of the changes in tensile properties, micro-structure, and dimensional stability of two magnesium alloys, AZ92A and AZ63A,+ as a function of aging time and temperature after solution heat treatment. Rates of precipitation in Mg-Al-Zn alloys are slow enough so that a substantially homogeneous, supersaturated solid solution can be maintained even when these alloys are air-cooled from the heat-treating temperature. Consequently, even though it has been demonstrated9 10 that significantly higher strengths can be developed in some alloys in the aged condition by quenching rather than air cooling from the heat-treating temperature, general practice is to air-cool magnesium alloys. All the work discussed in this paper is based, therefore, on aging studies performed on material air-cooled from the heat-treating temperature. This investigation was intended to be a study of commercially practical aging cycles; the tensile properties were determined, therefore, up to aging times of 25-hr duration. The alloys, used in this investigation were prepared in the laboratory by remelting commercial ingots of the appropriate composition according to the procedures described in a previous paper" as the "crucible method." All melts were given the standard superheating treatment in order to insure the maintenance of a uniform grain size of 0.003 to 0.004 in. Standard test bars, 61/2 in. long with a 2½ in. long reduced section having a diameter of Y2 in., were cast from these melts in green-sand molds using a four-bar pattern. The alloys were heat treated according to the following schedules: AZ92A alloy: 500" to 780°F in 2 hr + 780°F (24 hr) AZ63Aalloy: 500" to740°Fin2 hr + 740°F (16hr) In commercial practice," AZ92A alloy is heat treated at 770°F for 18 hr and AZ63A alloy is heat treated at 730°F for 10 hr. The slightly higher temperatures and longer periods of heat treatment were used in order to obtain as homogeneous a solid solution as possible and thus to minimize inconsistencies in the

Jan 1, 1952

By P. J. Soltis

Direct as well as indirect evidence of a-phase ordering was found in a "near-a" type titanium alloy, Ti-8Al-1Mo-1V. The annealed alloy showed an anomalous decrease in second-stage creep rate at 950°F (510°C) and 47,500 psi. Anomalous increases were noted in initial yield stress after 500 hr creep exposure and in tensile strength after 1100 hr creep exposure. Debye-Scherrer X-ray diffraction patterns obtained on fine-grained polycrystalline speci-ment showed much line broadening and development of superlattice lines after 500 hr at 510° C. Examination with the light and electron microscopes failed to reveal phase changes in thermally exposed material, but detailed metallography is presented illustrating the plastic and fracture characteristics of the alloy. Electron-metallographic evidence is presented, however, which shows the nature of the nucleation and growth of ordered regions from the disordered a in annealed material. In the original phase diagram of the binary Ti-Al system constructed by Ogden et al.1 aluminum was shown to be soluble in a titanium over a wide temperature range at concentrations up to about 30 pct. Subsequently, a number of papers2-7 have appeared which indicate the existence of either intermetallic compounds and/or ordered phases in the a field up to 25 pct Al. In the most recent of these, Goldak and Gordon paw7 have determined unequivocally the ordered hexagonal D019 structure for Ti3Al in a 25 pct Al alloy. No superlattice lines were observed above 1112°F (600°C). Previously, the embrittle-ment encountered by Crossley and Carew4 in low- temperature heat treatments of binary Ti-Al alloys low in aluminum had been attributed to the appearance of a new phase in light micrographs. In the present work, direct as well as indirect evidence is presented showing the existence of a-phase ordering in what is essentially the binary Ti-8A1 alloy containing small percentages of the ß stabilizers molybdenum and vanadium, i.e., the "near-a" Ti-8Al-1Mo-1V alloy. Although Bohanek and Kessler8 have shown that this alloy has good stability at temperatures up to 1100°F (593°C), the present work shows instability at 950°F (510°C) where long exposure times were used. Light and electron microscopy proved very useful in revealing the mechanical behavior of ordered a and led to the conviction that ordered "near-a" alloys may have remarkably good properties and useful engineering applications.

Jan 1, 1965

By P. Pollard

A method has been developed for evaluating acid treatments in fractured limestone fields by breaking down pressure drawdown into three component parts: (I) pressure differcntial across "skin" near the borehole face, (2) pressure differential due to flow resistance in the coarse communicating fissures and (3) pressure differential between the fine voids and the coarse fissures. It is apparent that in most successful acid treatments the first term, skin resistance, has been reduced or eliminated. Further, it is often possible to estimate the volume of coarse fissures associated with the second term, coarse fissure flow resistance. In cases where this volume is comparable with practical acid volumes it seems likely that this resistance also may be attacked with a suitably retarded acid. INTROD UCTION Acid treatment has been successfully applied as a general practice in the limestone wells in the Mara/ Maracaibo districts of Venezuela for some 10 years. At the same time the need has been felt for a more precise method of: (1) evaluating the effect of an acid job and (2) selecting wells which should benefit from an acid treatment. The following method, based on an analysis of build-up curves for wells producing from fractured limestone, provides a means of forecasting the effect acid will have on a well and in many cases the probable order of production rate increase which may be expected. In certain cases it is also possible to calculate the fissure volume through which the acid has to be displaced for best results. Various approximations are introduced in the method, but within the limitations of these the analysis gives an indication of how a well, whether previously acidized or not, may be expected to respond to acid treatment. Suitable build-up curves cannot be obtained on "tight" wells which do not give sustained production and the method is not applicable to such wells. Figs. 1 through 7 illustrate various types of build-up curves obtained from limestone wells in Western Venezuela. Curves are included showing (1) both skin and coarse fissure resistance, (2) skin resistance only, (3 and 4) reduction of skin resistance by acidization, (5) fissure resistance only, (6) reduction of coarse fissure resistance by acidization, and (7) acidization failure. This theory has been successfully applied for over three years during which 22 acid treatments have been carried out specifically to reduce skin resistance and three treatments to reduce coarse fissure resistance. The method has been found to be a useful aid in the selection of wells for acidization.

By A. C. Losekamp, J. B. Conway

Thermal-expansion data for, tungsten, rhenium, tantalum, .molybdenum, niobium, W-25 pct Re, Ta-10 pct W, ant1 Mo-50 pct Re are presented covering the range from room tempature to 2500°C. In these measureMents, made in a resistively heated tungsten tube furnace operating in a helium atmosphere, data for rod and sheet specimens were found to be identical; in addition, arc-cast and sintered tungsten were found to yield essentially identical results. Optical rneasurenlents of thermal expansion .made in any atmosphere other- than vacuum are subject to a refraction error which can be quite substantial. Specimens tested in helium appear shorter than when tested in racuum and hence a special correction factor must be applied to the helium data in order to obtain accurate results. WHILE it is true that linear thermal-expansion data for many of the refractory metals have been measured to very high temperatures, it is also true that except in a few instances the data from various investigators are not in good agreement. This is particularly evident in the case of tantalum and niobium although some tungsten data have been reported which differ by as much as 40 pct from the data of other investigators. Due to the sensitivity of both tantalum and niobium with respect to impurity absorption during exposure to high temperatures, it is probable that this single factor accounts for the majority of the discrepancies in the thermal-expansion data for these metals. However, this same factor can probably not be employed to explain the existing differences in the tungsten data. In all probability, these are due to errors in the measurement technique, to material composition variations, or to changes which take place in the material during the heating process (e.g., additional densifica-tion resulting from heating a sintered specimen above the original sintering temperature). In view of the discrepancies which exist in the linear expansion data reported for many of the refractory metals, the current study was initiated in an attempt to resolve such differences. Also, no high-temperature linear thermal-expansion data were found to be available for several refractory metals. Providing such data was another objective of the current investigation. MATERIALS In this study test specimens were employed in either rod or sheet form and in several instances both arc-cast and sintered material were employed. Material compositions are presented in Table I. Helium gas was fed to the furnace at a rate of about 0.5 SCFH and no special purification procedures were employed. However, the helium contained less than 50

Jan 1, 1967

By AIME AIME

T HE 121st meeting of the Institute held in New York City, February 16 to 19, 1920, was a great success despite vicissitudes of weather of unusual severity. On account of tremendous snowstorms, only two members of the Canadian contingent arrived, and several of our members from the west arrived thirty hours late. Two weeks prior to the meeting, the heaviest snowstorm in 34 years wrecked the surface transportation in New York; and it was only by special dispensation that arrangements were effected, with the New York Street Cleaning Department to clear away 39th street in front of this building so that vehicles could reach the curb. The total registration of members and guests was 1138.

Jan 1, 1920

By Philip S. Mathews

THE tremendous stimulus given to the mining industry by the gold and silver policy of the present administration has found the capital market for mines ill prepared to afford practical means of financing. Particularly has this been true of the host of abandoned high-cost producers and prospects which increased gold and silver prices have made potentially profitable. In a comparatively short time, experience has demonstrated abundantly that valuable properties have frequently failed to secure capital, while questionable properties have drawn to themselves and their promoters more of the public moneys than their prospects justify. Singularly enough the fault is usually attributable to faulty financing. Discussion and study of this problem are vital to the industry.

Jan 1, 1936