Search Documents

By A. J. Heckler, J. A. Peterson

A capsule technique was successfully employed to investigate the effect of nickel on the activity of nitrogen in Fe-Ni-N austenite in the temperature range 600" to 1200°C. This technique consisted of equilibrating nitrogen among various Fe-Ni alloys within a sealed silica capsule. Nitrogen transfer among the specimens occurred by N, gas at 900°, lOOO? and 1200?C. Nitrogen gas pressures within the capsules were estimated to be as high as 22 atm. The activity coefficient of nitrogen, fN , in Fe-Ni-N austenite is adequately described by the linear interaction equation: log . wt pct Ni where the standard state is chosen such that fN = I as wt pct Napproaches zero in binary Fe-N. This relationship was determined over the temperature range 873" to 1473°K and for nickel contents of 0 to 35 wt pct. ALTHOUGH chemical thermodynamics of liquid iron alloys have been extensively studied, experimental data for the solid state are needed. These thermody-namic data will provide a basis for understanding phase transformations, precipitation reactions, metal-gas equilibria, and so forth. The interaction of sub-stitutional alloying elements with the interstitial elements is of particular interest. In this investigation the thermodynamic behavior of Fe-Ni-N austenite has been studied. The solubility of nitrogen gas in iron austenite is known to obey Sieverts&apos; law up to about 65 atm.1-6 In addition, the solubility of nitrogen in Fe-Ni austenite has been investigated5"8 using the classical method of equilibrating Fe-Ni alloys with nitrogen gas at 1 atm. A capsule technique similar to that used to study the activity of carbon in alloyed austeniteg&apos;&apos;&apos; was employed in the present work to determine the effect of nickel on the activity of nitrogen in Fe-Ni austenite over the temperature range 600" to 1200°C. EXPERIMENTAL PROCEDURE A series of Fe-Ni alloys up to 35 wt pct Ni was vacuum melted and cast into 1 by 3 by 6 in. ingots. Chemical analyses at the top and bottom of each ingot demonstrated that the ingots were homogeneous with respect to nickel content. The nickel contents are given in Table I. Additional chemical analyses showed that wt pct Si < 0.05, s < 0.01, C < 0.01, Al < 0.006, 0 < 0.004, Mn < 0.002, and P < 0.002. A 2 in. section of each ingot was cold rolled to 0.015 in. The material was then decarburized to a carbon content of less than 0.004 wt pct. A portion of the material of each nickel content was nitrided to various levels in a H2-NH3 gas atmosphere to provide a source of nitrogen during subsequent equilibration. The experimental technique consisted of equilibrating the series of Fe-Ni-N alloys in a partially evacuated sealed silica capsule at the temperature of interest. Both Vycor and quartz capsules were used. In general, the final equilibrium nitrogen content for each Fe-Ni alloy was approached from both higher and lower nitrogen levels. The criterion for establishing that equilibrium was attained was that the final nitrogen content for each Fe-Ni alloy was the same irrespective of the initial level. A schematic drawing of the sample configuration in a capsule is shown in Fig. 1. The samples were arranged so that there was a minimum of physical contact. The samples were also dusted with a fine, high purity alumina powder to help prevent sticking. Several different types of furnaces were used in this study. In each case, a thermocouple was placed immediately adjacent to the capsule during equilibration and the temperature was controlled to within *4?C of that reported. At each equilibration temperature, the following times were found to be more than sufficient to attain equilibrium: 600°C-250 hr, 900°C-150 hr, 1000°C-150 hr, and 1200°C-50 hr. After equilibration the capsules were quenched in water and the nitrogen contents of the specimens determined by a Strohlein analyzer. Analyses of samples after equilibration at 1000" and 1200°C showed no silicon pickup from the silica capsules. RESULTS AND DISCUSSION Transfer Mechanism. The mechanism by which nitrogen was transferred among specimens in an initially hydrogen flushed and partially evacuated capsule equilibrated at 1000°C was investigated. After equilibration the gas in the capsule was collected over water and an estimate of the pressure at temperature

Jan 1, 1970

By R. B. G. Yeo

The effects of alloy additions on the M, and A, temperatures of an Fe-22.5 pct Ni alloy have been determined. Increasing amounts of titanium, colum-bium, vanadium, and silicon raise and then lower M,while raising A, cmtinuously. Cobalt raises both M, and A,. Aluminum has little effect on Ms but raises A,. Chromium md nickel lower M, and A,. It is proposed that elements raise M, in accordance with their effect on the Ae3 temperature of iron until the lattice becomes stiffened against the shear transformation so that M, is then lowered. An anomaly, first pointed out by Zener,1 arises in steels when the addition of elements, such as molybdenum and tungsten, which raise the Ae3 temperature, also lower the M, temperature.2&apos;3 During the development of a series of martensitic precipitation-hardening (maraging) steels, the effect of several elements on the transformation of austenite to martensite was studied. The results show that under suitable conditions several elements which raise Ae3 also raise the M, and A, temperatures. PREPARATION OF MATERIALS STUDIED A series of alloys was made in which cobalt, titanium, columbium, vanadium, silicon, aluminum, molybdenum, chromium, and nickel were added to an iron base containing 22.5 pct Ni. The compositions of the alloys prepared are given in Table I. The residual manganese contents of the heats were in the range of 0.030 to 0.35 pct, silicon 0.05 to 0.1 pct, carbon 0.0008 to 0.009 pct, and nitrogen from 0 to 0.004 uct. The allois were made as 50-lb induction heats starting with electro-iron and electro-nickel, melted in air to oxidize impurities. Additions of silico-manganese and ferro-silicon were made after which the power was turned off to allow the products of deoxidation to rise and be skimmed from the surface of the melt. The furnace chamber was pumped down to a pressure of 5 p and the charge was heated to 2900°F for the addition of other alloying elements. The heats were poured into five 10-lb ingots, making successive alloy additions to each. The ingots were soaked for 2 hr at 2300°F and hot-worked to 3/4-in.-diam bars. This stock was heated to 1500°F for 1

Jan 1, 1963

By N. A. D. Parlee, N. M. El Tayeb

Fe-V alloys with small percentages of vanadium show no deviations from Sieverts&apos; Law up to P~, = 1 atm in the 1600º to 1750ºC region. At somewhat under 8 pct V and up to at least 20pct V, at 1604" and 1661 °C, nitrogen absorption follows Sieverts&apos; Law at low Pn2 values, but deviates from this law beyond critical values of pn2, due to formation of a nitrzde phase of approximately VN composition. The behavior below these solubility limits can be described at all temperatures by the equations: RAO and parlee1 suggested that the nitrogen absorption curve for liquid iron alloys takes the general form shown in Fig. 1 when an alloy nitride precipitate is formed. They showed that the precipitation of 6 titanium nitride from liquid Fe-Ti alloys follows this general scheme and dealt with the general theory involved. Recently, Evans and Pehlke2 reported their research on the precipitation of aluminum nitride from liquid Fe-A1 alloys. Fountain and Chipman&apos;s recent paper3 on the precipitation of boron nitride from solid solution contains a fine example of the analogous behavior which they have been studying in the solid state. Researches on the absorption of nitrogen by liquid Fe-V alloys have been described by various authors.1,4-7 Most of this work has been confined to fairly low vanadium concentrations and rather high temperatures because of difficulties variously described as, formation of surface scums, bridging, and so forth. This behavior and the rough thermo- dynamic calculations made by chipman,8 over eleven years ago, indicated that excessively high vanadium concentrations should not be required for vanadium nitride precipitation. It seemed desirable to look for and study this precipitation in order to fill out the thermodynamically interesting nitrogen absorption data on these alloys. EXPERIMENTAL METHOD The general method used was essentially the same as employed by Rao and parlee,1 in which a Sieverts type of apparatus was used and the precipitation of the nitride detected by the "break-point" in the Sieverts&apos; Law line, and by the visual observation of the formation of the new phase on the surface of the melt. There were, however, a few differences in apparatus and technique as described below. The oil manometer used by Rao and parlee&apos; to measure low partial pressures of nitrogen was not employed. The present authors sought to avoid as much as possible the exposure of the liquid alloy to low total pressures of gas during the 6 to 10 hr long runs because of the heavy iron evaporation-loss errors involved. This was achieved, partly by keeping evacuation times to a minimum with fast pumping but largely by the use of two burettes, one for argon and one for nitrogen, and using them to equilibrate the alloy with mixtures of argon and nitrogen rather than nitrogen alone. Each run involved a careful sequence of operations. After melting, de-

Jan 1, 1963

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa&apos;s6 and M. Okamoto&apos;s7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith&apos;s latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter&apos;s diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940

By G. H. Anderson

During an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investigation was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this system as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa&apos;s6 and M. Okamoto&apos;s7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. 5. Smith&apos;s latest work on the copper-silicon systema was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter&apos;s diagram and ours checked in all essential features, except the temperature of the peritectoid line above 830" C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centcrcd cubic with a lattiee constant of 2.848 ,&. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexagonal phase, and to avoid confusion this designation will he adhered to in the present paper. Preparation of Samples The alloys were melted in vacuum in a high-frequency furnace. from copper cathodes containing 99.98 per cent Cu, and specially refined silicon supplied by The Electro Metallurgical Co. This silicon is stated

Jan 1, 1940

By W. P. Saunders, W. R. Hibbard, G. H. Eichelman

Interest in the various products of the austenite eutectoid transformation in iron-carbon alloys, particularly as produced by the isothermal sub-critical techniques introduced by Davenport and Bain,&apos; has resulted in the application of similar heat treatments to other eutectoid transformations. Studies o f the beta copper-aluminum alloy eutectoid transformation revealed microstructures very similar to those found in iron-carbon alloys. Investigations5t6 of the kappa phase in the copper-silicon alloy system have established the eutectoid type transformation of this phase into terminal alpha and intermediate gamma phases. This transformation has been reported5 as forming a eutectoid type structure in a very sluggish manner by a long time isothermal treatment. The purpose of the present investigation is to study the products of the kappa eutectoid transformation as affected by transformation temperatures by means of microscopic and hardness methods. Preparation of Alloys The copper-silicon alloy equilibrium diagram is shown in Fig 1. The kappa field converges to a minimum silicon solubility at the eutectoid composition and all other completely kappa alloys are hypereutec-toid. Thus, kappa decomposition involves first the proeutectoid precipitation of gamma, followed by the eutectoid transformation of a lower silicon content kappa (5.2 pct) Smith6 has indicated that alloys containing between 5.4 and 5.7 pct silicon could be hot rolled, but that the latter composition was desirable in order to permit a wider kappa temperature range. The alloy was prepared by adding Baker&apos;s commercially pure silicon to an ingot of copper-silicon alloy containing 2.34 pct silicon remaining from the investigation of Brick, Martin and Angier.&apos; Following the casting techniques of Krynitsky, Saunders and Stern,s the ingot was melted under a heavy layer of dried charcoal in a clay-graphite crucible in a gas-fired pot furnace. Small lumps of silicon were held under thc melt surface with a graphite rod. After the silicon had dissolved, the alloy was chill-cast and then remelted without a cover, stirred thoroughly, skimmed and poured into a preheated cast iron mold. The cast microstructure is shown in Fig 2. The casting, 10 X 4 X K in., was annealed at 750°C for 21 hr and furnace cooled, About }{& in. was milled from all surfaces. The plate was cut in half longitudinally and the bottom half analyzed by A.S.T.M. and The composition by weight was as follows: copper 94.24 pct, silicon 5.56 pct, iron 0.11 pct.

Jan 1, 1949

By G. H. Clevenger

(Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133.) This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developments which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be : First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all times a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the. bulk of my discussion will be confined to the presentation of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and .the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation of data y others of practice in other districts which will&apos; assist in reconciling this divergence of opinion.

Jan 7, 1914

By G. H. Clevenger

Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914. See Trans., xlviii, 3 to 32 (1914). This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developzn~ents which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be: First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all limes a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the bulk of my discussion will be confined to the presentation Of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation by others of data of practice in other districts which will assist in reconciling this divergence of opinion.

Jan 1, 1915

By P. K. Strangway, H. U. Ross

Briquets consisting of pure artificial magnetite, pure artificial hematite, and mixtures of the two were reduced by hydrogen in a loss-in-weight furnace at temperatures in the range 500° to 1000° . The rate of reduction of the pure hematite briquets increased continuously with increased temperature. In contrast, the pure nmgnetite briquets exhibited a pronounced rate ninimutn at about 700°C. Metallographic studies of partially reduced briquets rerlealed that, at this temperature, the he.matite samples reduced in a topo-chemical manner while the magnetite ones reduced uniformly throughout, and after partial reduction their cross sections contained a mixture of iron and unreacted wustite grains. No iron shells could be detected on the surfices of any of these uwstite grains. X-ray diffraction investigations indicated that these grains had a rzinimum lattice parameter when they had been formed at the rate rninimum temperature. Also, it was found that an activation energy of 41,000 cal per mole zoas required for reduction when only these wustite grains were present. Thus, it is suggested that the overall reduction rate of the rnagnetile su?nples at temperatures in the range influenced by the rate nzinirnum phenomenon was limited by the rate qf iron ion diffusion in the unreacted wustite grains. THE rate minimum phenomenon, which has often been observed when reducing iron oxides at a temperature of about 700°C, is one of the most interesting, yet unresolved, problems in the field of reduction kinetics. Basic principles of chemical kinetics and &apos;In some instance, a second rate minimum has been observed at about 900°C. Since most investigators are in agreement that this minimum is directly related to the transformation from a to y iron (which takes place at 911°C) and since it was not encountered during the present reduction tests, it will not be referred to in this vaver. fundamental laws of diffusion all agree that, as the temperature is increased, the rate of reduction should also increase. However, with certain ores, it has been found that their reduction rate actually decreases with an increase in temperature up to some value X where a minimum reduction rate is reached. With further temperature increases beyond X the rate becomes more rapid again. Temperature X is usually referred to as the "rate minimum temperature", while the overall type of behavior constitutes the "rate minimum phenomenon". This phenomenon has been reported by numerous investigators. They have found rate minima during the reduction of both artifiial&apos; and natural374 magnetites and artificia15j6 and natural5" hematites. Rate minima have been observed when reducing high-purity material2 or low-grade ores,3&apos;4 when studying particles in the micronsize range5 or relatively large agglomerates,g10 and during reduction with either hydrogen7 or carbon monoxide.11"2 Previously, this phenomenon has been attributed to many factors; these include sintering and recrystallization of the iron formed during reduction374 changes in microporosity of the ore upon redction,"" formation of dense iron shells around retained wustite grains,11716 and chem-isorption,17 to name only a few. However, most investigators who have reported a rate minimum merely speculated as to what seemed to influence it and they did not examine the fundamental causes. Consequently, the present experimental study was initiated in order to evaluate the basic factors which could be associated with this phenomenon. MATERIALS AND METHODS The experimental techniques, followed during this investigation, are similar to those which have been described previously.18 The chemically pure magnetic powder was prepared by partially reducing Fisher reagent-grade hematite with a gaseous mixture of carbon monoxide and carbon dioxide in a rotating-drum furnace. Three-quarter-inch diam cylindrical briquets which weighed about 12 g were formed from this magnetite powder and pure hematite powder. All of the briquets were sintered while they were slowly raised through the 1200°C hot zone of a vertical tube furnace. An argon stream was continually flushed through this furnace in order to prevent oxidation of the magnetite briquets, while in the case of the pure hematite briquets sintering was carried out in air. The sintered hematite briquets had a density of 5.06 g per cu cm while the density of the sintered magnetite briquets was 4.27 g per cu cm. The sintered briquets were reduced by purified hydrogen in a loss-in-weight furnace at temperatures in the range 500" to 1000°C. In all instances, the critical reducing gas velocity was exceeded and, in order to ensure that the results were reproducible, duplicate briquets of each type were reduced under each set of experimental conditions. A continuous record of the weight loss during reduction was obtained with the aid of a Statham transducer. The present experimental setup was capable of detecting a change in weight as small as 10 mg. Since a weight loss of over 2 g usually occurred during each reduction test, an accuracy of better than 0.5 pct of the total weight loss could be achieved. RESULTS AND DISCUSSION Reducibility Tests. In the first set of experiments, pure hematite and pure magnetite briquets were used.

Jan 1, 1969

By AIME AIME

T HE 133rd meeting of the A. I. M. E., opening in New York on Feb. 15, promises to be as successful technically and socially as any in the past. The papers submitted for the various technical sessions are unusually excellent and insure something of interest to every group. Tentative programs have already been issued, and a concise resume of the various sessions, arranged chronologically, appears on page 48. Among the many interesting technical sessions arranged, attention is directed to those of the Petroleum Division, embracing the Symposium on Production that has come to be an annual feature, and new ones on refining practice, transportation and economics. The Institute of Metals program is similarly comprehensive. It includes 15 papers, 8 on copper, 4 on aluminum and its alloys, and one each on magnesium, lead, and fatigue of metals. The Coal Committee offers as a leading contribution its report, prepared under the direction of H. N. Eavenson, giving a new analysis of the capacity of the mines and a comparison of coal with other industries. This will be supplemented by a number of other papers of especial interest to operating men, among which are "Data on Use of Loading Machines in Bituminous Mines," by Graham Bright; "Evaluation of Coal," by R. H. Sweetser; "Selection of Coals for the Manufacture of Coke," by H. J. Rose; and "Relation of Origin and State of Carbonization of Coal to Problems of Low Temperature Carbonization," by S. W. Parr. The Iron and Steel Committee has scheduled seven papers, and there will be a special session on open-hearth practice, in which will be presented the first results of the two conferences, held by the sub- committee at Pittsburgh and Cleveland. A symposium on molding sands will be a special feature of the session on non-metallics.

Jan 1, 1926

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,&apos; conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

Willet G. Miller, Toronto, Canada (communication to the Secretary): In his interesting paper Mr. Lindgren says: " As to ultimate results, it would seem as if we should be justified in concluding, with Prof. Suess, that the gold-supply of the world will gradually decrease if no further important improvements are made in the processes for the extraction of this metal; but regarding events so far distant no predictions may safely be made." It seems to the writer that no very important improvements require to be made in order at least to keep up the present production for many years to come. In many parts of the world there are large deposits of auriferous material which can be worked if present conditions are slightly changed. In the territory occupied by the Archean protaxis of the Province of

Jan 1, 1903

By P. W. Barton, A. A. Johnson, E. J. Hughes

THE only systematic work on the effect of carbon on the recovery and recrystallization kinetics of iron so far reported in the literature is that of Venturello et al.1 These workers found that doping high-purity iron so that it contained up to 86 ppm C caused a marked retardation of recovery but had little or no effect on the recrystallization kinetics. Such evidence for an effect as was obtained was inconclusive. In the course of a study of electron-beam zone-refined iron the authors have recently examined the effect of added carbon on the recrystallization kinetics of this material. The amount of carbon added was about 50 pct more than was used by Venturello et 01. and definite evidence was obtained that carbon at this level retards recrystallization. The starting material was taken from a batch of 0.2-in.-diameter Johnson-Matthey spectroscopically pure iron rods which had been further purified by being given three passes at 4 in. hr-1 in a standard MRC electron-beam zone-refining unit. The purity of this material. which was used in two other investigations of the properties of high-purity iron,2,3 was established by an extensive series of analyses. Four laboratories, the National Research Corp., Newton, Mass., the Naval Research Laboratory, Washington, D.C.. the Battelle Memorial Institute, Columbus, Ohio, and the National Physical Laboratory. Teddington. Middlesex, England. carried out analyses for carbon. oxygen. and nitrogen. and in addition a complete mass-spectrograph analysis was carried out at Battelle. In all, twelve analyses were carried out for carbon, seventeen for oxygen and twelve for nitrogen. The amounts of these elements found to be present were 10 * 7, 8 i 5, and 0.9 i 0.1 ppm, respectively. The limits given are rms deviations. Two results, one of 46 ppm of oxygen and another of 31 ppm of nitrogen, were rejected as anomalous. The mass-spectrograph analysis revealed the major impurity to be 25 ppm of tungsten. All of the other elements detected were present in amounts less than 0.5 ppm. Some of the rods were doped with carbon by being immersed in a suspension of carbon in oil, heated in a vacuum at 400°C, and then zone-leveled to make the distribution of carbon uniform. Carbon analyses carried out on three of the doped rods gave a mean value of 130 ± 45 ppm. Some of the doped and undoped rods were deformed 58 pct by swaging and cut into specimens 1/2 in. in length. Isothermal recrystallization experiments were then carried out on them at 575", 600°, 615", 630°, and 650°C, the volume fraction of each specimen recrystallized being measured by a point-counting method described by Hilliard and Cahn.4 The results for the two types of specimens are shown separately in Figs. 1 and 2. In Fig. 3 the pairs of recrystallization curves for each temper-

Jan 1, 1965

By W. Mostowitsch, H. O. Hofman

In a previous paper,&apos; The Behavior of Calcium Sulphate at Elevated Temperatures with Some Fluxes, we published the results of our investigation into the behavior of calcium sulphate in air; that is, under oxidizing conditions. The results as a whole hold good for a neutral atmosphere, or one which has no chemical effect upon calcium sulphate. The present paper deals with the behavior of calcium sulphate under reducing conditions, the reducing-agents employed being carbon monoxide and carbon, and the changes the calcium sulphide formed undergoes when it is subjected to an oxidizing-roast. Technical literature deals very sparingly with the subject. The information furnished by the recent leading chemical manuals is general. Thus Dammer,2 Missan,3 and Abegg4 quote Berthier as having reduced, in 1823, calcium sulphate with carbon, and Stammer as having done the same in 1851

Jan 1, 1911

By Arthur G. Metcalfe

Arthur G. Metcalfe (SOLAR)—Three explanations to account for mechanical nucleation effects are considered in the paper, viz., theories based on fragmentation, agglomeration, and pressure-wave mechanisms. The authors show that none of these mechanisms will explain the results observed with tin and Sn-Pb alloys. A fourth mechanism of nucleation enhancement was developed during work at Armour Research Foundation on casting of beryllium and, although presented briefly on various occasions, the theory has never been discussed adequately. It is believed that this theory will explain many of the observations. Classical homogeneous nucleation theories assume that embryo nuclei are formed in the melt as a result of compositional and/or thermal fluctuations. Stable nuclei are formed when a critical size is reached such that the decrease in free energy for conversion of this volume of melt to solid offsets the increase of surface, energy. The assumption is made that the average properties of liquid and solid metal can be used. In practice this assumption is invalid and indeed is contrary to the postulation of thermal and compositional fluctuations in the melt. Actually the conditions favoring embryo formation bring the seeds of its own destruction—the thermal and compositional fluctuations leave the embryo surrounded by atoms of higher thermal energies and/or by solute atoms that depress the melting point. Any mechanical method of dispersing this destructive

Jan 1, 1964

By Charles W. Henderson

THE influence of mineral production on the development of the western United States has been profound. From 1848 to 1860, there was only gold production, the effect of silver began in 1860, and from then on both had a powerful influence. Lead production started in 1863, copper in 1863, and zinc in 1885, but was small until 1898. Gold alone was therefore the stimulus of the early settlement and exploration of the Western States.. But mineral deposits caused neither acquisition of territory nor determination of boundary lines. Arizona, California, Nevada, New Mexico, and parts of Utah, Wyoming, and Colorado were formally acquired from Mexico fourteen days after the actual date of the discovery (January 19, 1848)1.2 of gold at Sutters Mill, near the present town of Coloma, California (a discovery which, with the immediate new discoveries, aroused the world several months later) ; but the acquisition was by treaty (under negotiation for some time but signed February 2, 1848)3 in settlement of a war involving the boundaries of the grassy plains of Texas, an area at that time not known to contain any metals, and to date found to have but few metal deposits.4 The international boundary at 49º latitude for the far northwest states was determined by causes other than mineral deposits.

Jan 1, 1933

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965

By A. U. Seybolt

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except .conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

Discussion of the paper Of JAMES JOHNSTON, presented at the New York meeting, February, 1914, and printed in Bulletin No. 85, January, 1914, pp. 107 to 133. CHAIRMAN E. GIBBON SPILSBURY.-I would like to call attention to the fact shown in this paper that less than five years or perhaps seven years ago nobody had thought it possible to cyanide with success silver ores. The cyaniding of silver and gold ores was first of all started in Mexico, and gradually extended to this country in the case of the silver ores alone. The average extraction, I think, for the metals in Mexico, in the case of the silver ore, is less than 85 per cent., whereas here, in the case of a very complex ore, carrying a high percentage of sulphur and arsenic, and other objectionable elements, the ore has been treated so as to extract an average of 95 per cent. of the silver contents of the ore. It is really a phenomenal revolution in the metallurgy of silver ores which has been demonstrated and worked out at the Nipissing mines. GEORGE A. PACKARD, Boston, Mass.-I would like to suggest a slight modification, perhaps, of the statement which is made that no one considered cyaniding of silver ores up to five, or perhaps seven years ago, because in 1897, when I was at Mercur, Utah, one mill near there was operating on silver ores. It did not operate very successfully from a commercial standpoint, because they did not have a great deal of ore, but the extraction, I was told, was very satisfactory, and I am quite confident that it was, because, as suggested by the name, Chloride Point, the ores were silver chloride ores, and of course very easily soluble. Some years before that, in 1892, I made some tests myself. I spent three months making tests on more or less complex silver sulphide ores at Virginia City, Mont., and while our tests on the plain sulphide ores, finely ground, were quite successful, on account of the presence of a small amount of copper we did not work out a satisfactory solution of the problem at that time; although since then a cyanide plant has been erected and for at least eight years these ores have been treated by cyaniding at Virginia City, and the mill is still in operation. The period of five to seven years should, therefore, be modified considerably, in justice to the pioneers in the cyanide processes. REGINALD E. HORE, Toronto, Ont., Canada.-I hoped that there would be metallurgists from Cobalt here to present and discuss Mr. Johnston&apos;s paper. In their absence a few remarks from me may help to make clearer to you what they have accomplished.

Jan 6, 1914