Search Documents

By W. W. Krysko

In order to calculate the critical particle size of lead oxide entrapped in lead, Stoke's Formula may be applied. All data were available except figures for the density of lead oxide at elevated temperatwes. The density of lead oxide was determined by means of dilatometmetrc and volumetric methods up to 1010°C. Graphs of the density of lead and lead oxide as well as the viscosity of lead are given and discussed, with the conclusion that the most unfavorable region for the separation of lead oxide from molten lead lies just above the melting point of lead. DURING previous investigations, particularly on the dedrossing of lead with aluminum1 and the oxygen solubility in lead,' the critical particle size of lead oxide which could be entrapped in solidifying lead was estimated by calculation, and it was shown that high values found for the oxygen content of lead may be due to the method of sampling and the entrapped particles of dross. Unfortunately, due to lack of data, an exact mathematical solution was not possible. The particle size which will separate under a given condition can be estimated from Stoke's Law, which states that where: d = diameter of the critical particle size ¦q = viscosity of lead in Poise V = constant velocity in cm sec-I g = 981 cm sec-2 61= specific gravity of lead 62= specific gravity of lead oxide The depth of the lead bath and the time before solidifying define the velocity. The viscosity of molten lead is known from earlier work by Krysko and is given in Table I. The specific gravity of lead is also known, see Table II. These values are according to Hofmann. A careful survey of literature revealed no values for the density of lead oxide at elevated temperatures. The present investigation was therefore conducted to provide this information. RESEARCH INVESTIGATIONS The density of lead oxide was determined from the following experiments: 1) Determination of the density of lead oxide at room temperature. 2) Dilatometric investigations on the same samples. 3) Determination of the shrinkage at the liquid-solid trans£ormation. 4) Density determinations on liquid lead oxide. 5) Time temperature curves during cooling. 1) The samples for the determination of the density of lead oxide in the solid state were prepared in the following manner. Molten lead oxide was cast into I hot mold which could be opened along the longitudinal (vertical) axis. The cast samples were cylinders of approximately 10 mm diam and approximately 80 mm length. The cylindrical hot mold was open at both ends and was placed on a large copper chill plate shortly before casting. The solidification of the lead oxides proceeded upwards without any formation of internal cavities. The sample was carefully checked with respect to density and crystalline appearance, and only the lower portions which were crystalline and free from porosity were used. The density was determined in a specially made pyknometer-like container, where the surplus liquid was squeezed out through an orifice approximately 1/10 mm in diameter. Mercury or water was used as the liquid. The densities of the samples were calculated from the weight, volume, and mean specific gravity of eight samples was 9.62 * 0.05 g cm"3 at 22"~. 2) The samples were machined to approximately 1 1/2 in. in length and fitted into a dilatometer. A

Jan 1, 1962

By W. O. Crosby

INTRODUCTION. THE crystalline belt of the Atlantic Seaboard, south of New York, attains its maximum breadth of 220 miles on the northern border of North Carolina; and in this State it is most widely characterized by the occurrence of gold in workable deposits. Half a dozen auriferous belts have been recognized by Nitze and Hanna.1 These are, in the main, coincident in position and trend with the NE.-SW. zones of metamorphic slates and schists, which, more than any other feature, give character to the geological map of North Carolina. The central gold-belts, accompanying the main zone of slates and associated igneous rocks, are much the more important and persistent, and may be regarded as continuous northward across Virginia and southward into South Carolina. Tile eastern belt, on the other band, is the shortest and, economically, one of the least important. Its extreme length does not exceed 25 miles, the narrow band of slaty rocks to which it belongs passing, both NE. and SW., beneath the coastal-plain formations. But, although limited in area and production, this belt is, perhaps, comparable with the central belts or any part of the sea-board crystallines in the variety of conditions under which the gold occurs. It lies chiefly in the NE. part of Franklin county and the NW. part of Nash county, on the watershed of Fishing creek and other tributaries of Tar river. The elevation is between 400 and 500 ft. ; and the Tertiary peneplain has here an exceptionally perfect development, the reliefs separating the slightly incised stream-courses consisting of broad, flat-topped peneplain remnants, bounded by gentle lateral slopes.

Mar 1, 1908

By D. M. Milne, R. F. Stoner, W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of fresh water whose origin can be traced to the present and historical courses of the River Indus. In the past, the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water table has risen to within a few feet of the surface. The river system itself is being progressively devel-oped for irrigation and very shortly a situation will arise where the entire low winter flow will be utilized. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilize the water table at safe depths. This paper discusses some of the methods used to ensure optimum economic development of the fresh groundwater and describes the general design philosophy evolved by the authors' firms for both irrigation and drainage wells, with respect to both well configuration and operation. Water quality standards are discussed insofar as they affect subsequent use of the groundwater. A few particular aspects are considered, including the values of the relevant aquifer constants, the construction of wells, and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to produce fresh water from layers overlying saline water. This solution is also discussed. The recent interest in the groundwater of the Lower Indus Plains of West Pakistan has two main aspects. Firstly, soil waterlogging and the associated salinity hazards caused by rising water tables are a serious problem in agriculture, and the ease with which drainage requirements can be met by aquifer pumping makes this an obvious solution. The second interest stems from the rapid intensification of irrigation agriculture and the growing shortage of water supplies. In the areas where the groundwater is of suitable quality it can be used immediately for irrigation at relatively small cost and with large financial returns. In addition, the aquifer forms a potential storage reservoir which could be recharged from high river flows and depleted by pumping at times of scarcity. SOURCE OF GROUNDWATER The Lower Indus plain is a relatively long and narrow alluvial basin on a north-south axis, some 23,000 sq miles in area, bounded by higher land to the east and west. One hypothesis to explain the distribution and quality of groundwater in the region1 presupposes a river system considerably larger than, but very similar to the present river. This is characterized by a single mainstream, with subsidiary overspill channels in times of flood, running along the crest of a self-deposited ridge and with an extensive advancing delta. Sea water is contained in the alluvial pores of the advancing delta, forming the native groundwater. This has been partially displaced from two sources, namely direct seepage of fresh water from the river channel in meander flood plain areas and percolation from flood spillage in cover flood plain areas. Percolation has been subject to much re-evaporation and is thus slightly saline even as it reaches the groundwater. The whole complex has been further affected by two main influences: evapotranspiration from the land surface that tends to salinize the groundwater and down-valley flow that tends to bring fresher water

Jan 1, 1970

By AIME AIME

A PERIOD of business depression and falling prices always raises questions as to the possible responsibility of the monetary or banking system. This is natural enough, for it is agreed that the supply of money or credit is a very important factor in modern business and in prices. However, it is far from being the only important factor. One of the chief merits of the gold standard is that under its workings the supply of currency and credit is regulated automatically to the masimun extent, in- stead of by the control of any arbitrary authority. The supply of new gold comes from the mines, and mining is free. It is distributed among the countries by the currents of trade and the play of economic forces, with the general result that the distribution tends to be in accordance with the economic development of the countries and their ability to use it or command it. Inasmuch as the accumulated stock of monetary gold is very large in comparison with the annual additions, the total avail- able supply changes but little from year to year, and it may be assumed that price-changes that are properly chargeable to gold will take place gradually rather than suddenly.

Jan 1, 1930

By David B. Dill, Edgar R. Lea

The zinc deposits of the Balmat-Edwards Division of the St. Joseph Lead Company in northern New York State provide some 10 per cent of the domestic zinc produced annually within the United States. These complex ore deposits are contained within marbles of the Precambrian Grenville series, in a repetitive sequence of dolomites and silicated units. The Balmat ore bodies are localized at various intervals throughout some 1800 feet of the stratigraphic column on the northwest side of a band of gneiss that has continuity to the Edwards area, some 10 miles to the northeast. The Edwards ore bodies are located to the southeast of this gneiss. The marble formations are thought to have included repetitive intervals of marine sedimentation that provided mineralized source "beds" and were subsequently folded, flooded, and injected with melts at great depth and were sheared, recrystallized, and reconstituted. Detailed structural and stratigraphic studies throughout the northwestern Adirondacks, in the Balmat-Edwards district, and at each mine in particular indicate the close dependence of the ore deposits on the enveloping structure whether it be local, district-wide, or regional in scope. Primary folding has developed a northeast regional trend with northwest dips. Secondary folding has been developed by an almost horizontal northeast-southwest-oriented shear couple in the plane of the regional trend. The secondary folding has produced crossfolds that intersect the regional northeast trend and plunge north to northwest at various angles. The ore bodies are found within certain stratigraphic horizons where repeated alternation of competent and incompetent beds encouraged unusually complex folding. Analysis of individual mine structures indicates that the location of each deposit is controlled by structural crossing of primary and secondary folding. The ore bodies, which are tabular, lenticular, or pod-like in form, have features that suggest parallelism to true bedding or modified flow banding, developed by northeast-southwest shearing stresses related to the development of the crossfolds. The ore deposits in general follow both structural and recrystallization trends within the wall rocks. Mobilization of the pre-metamorphic ore minerals is believed to have involved a combination of plastic flow under stress and solution of the sphalerite, minor galena, and pyrite. The ore fluids are thought to have been guided by secondary shearing and microbrecciation into structurally prepared areas where reprecipitation took place. The presumed premetamorphic mineralization now exhibits epigenetic high-temperature features related to late-stage metamorphism.

Jan 1, 1968

By Robert Phelps

A STUDY of solid solutions has long been a source of interest because of the conditions -controlling their formation. X-ray investigations so far have been conducted with the idea that there were two types of solid solutions. In the first type, an atom of the solute was supposed to replace an atom of the solvent in the crystal lattice. In the second type, an atom of the solute was supposed to lie in one of the interstices between the atoms of the solvent. These pictures both require that the sizes of the atoms must play an important part in the process of solution. It is the purpose of the present investigation to study the mechanism of solid solution, using pure silver as the. solvent, and pure aluminum as the solute. X-ray measurements show that these elements have the same "shape" of atomic domains (they both crystallize as face-centered cubes) and that their atomic diameters differ by less than one per cent.1 The results of the present investigation point toward a chemical rather than a physical picture of the nature of solid solution, and make the older' pictures merely special cases of a more general picture. The new theory has the advantage, too, that it offers a rational explanation of certain phenomena which hitherto have been only interesting detached facts. The aluminum-silver system which was, chosen for this study has been studied by various methods by several workers. By means of thermal analysis Gautier2 and Petrenko3 have determined the phase diagram. Hansen4 studied the aluminum-rich alloys by means of thermal and microscopic analyses. , He showed that at high temperatures silver dissolved in aluminum to the extent of 47 per cent by weight at 5600 C. But this solubility decreased to 1 per cent at 200° C. Westgren and Bradley5made an extensive X-ray study of these alloys. They used the change in the lattice parameter of silver as a criterion of the solution

Jan 1, 1932

By L. W. Davies

A problem often encountered is the provision of materials which have impurity contents below a certain specified level. This problem is in some cases solved by making use of the segregation of the impurity with respect to the liquid and solid states of the material: an ingot of the material is subjected to directional solidification and the ends of the ingot. which are richer in solutes which respectively raise and lower the melting point of the solvent, are removed. An important extension of this process is the zone-refining process invented by Pfann,' in which molten zones are passed successively along the length of an ingot and displace solutes towards the ends. Pfann's process is particularly appropriate in cases for which the segregation coefficient k does not differ greatly from unity, or when the impurity content must be kept extremely low (=10-6 atom fraction); it is widely used, particularly in the purification of materials for use in semiconductor electronic devices. It is the purpose of this paper to investigate theoretically the efficiency of the above refining processes; that is! we determine the most economic method of attaining a given yield of solvent of specified purity, taking into account the variables of the process. One variable of interest is the effective value of the segregation coefficient. which depends on the rate of movement of the liquid-solid interface and on the degree of stirring in the liquid; in addition to this, in the zone-refining process we are also interested in the choice of zone length for most efficient operation. A mathematical determination is made here of the lengths of successive molten zones which give, for an initially uniform distribution, the most efficient removal of a solute of arbitrary distribution coefficient. In order to be able to give a quantitative treatment of efficiency, we first define figures of merit applicable to a given distribution of solute. FIGURE OF MERIT Let an ingot of length L contain a distribution y(x) of solute: we confine our discussion to mono-tonic distributions, in order to avoid inconsistencies in the subsequent analysis. The first moments of the distribution about the origin and x = L are respectively L F = hy{x)dx [I] G = f(L -x)y(x)dx = YoL2-F, [21 where yoL is the total amount of solute present. We shall see that the quantities F and G are useful figures of merit for a discussion of the efficiency of zone-refining processes. In the first place, it is

Jan 1, 1960

By W. S. Ayres

The construction of a new breaker at the Cranberry Colliery, Hazleton, Pa., was forced upon the operators, A. Pnrdee & Co., by a fire which destroyed the entire plant early in January, 1896. The loss included, in addition to the breaker, three boilerhouses and three engine-houses. The boilers were not injured, but the steam-pipes and connections were all broken and warped by the fire. The boilers were probably saved from injury by the presence of mind of the fireman., who started all his feed-pumps and filled the boilers with water. The hoisting-engines were more or less warped and cracked, but by patching and replacing the injured and broken parts, they were made to do satisfactory service in the new plant. It may be worthy of mention that the wrought-iron shaft of one of the hoisting-drums, 12 inches in diameter by 17 feet long, was so heated in the fire that the weight of the drum caused it

Jan 1, 1899

By John Boardman

THE Anaconda company has never indulged in any employee activities at Butte which might be termed paternalistic, but it has exerted a vast amount of effort in care of its employees during working hours. The reason for this policy is not lack of interest or that the company does not feel the effect of employees' activities while they are "off the job"; it is that the company and the city of Butte have grown up together and, each has been adequate in its own sphere, the company in providing employment at the highest possible wage and the city in providing housing, sanitation, commercial services, medical services, schools, churches, amusements and entertainments. The one exception to this independence between the company and the community is the Butte Water Co., which is a wholly owned sub-sidiary of the Anaconda Copper Mining Co. Mention of this relationship is made here because the water supply of such a city as Butte is one of the principal factors in determining the health of the people. Very early in the development of the Anaconda company an adequate and dependable water supply for the operations became necessary, therefore the company took over this important community function. So well has this activity worked out that during the whole period of time covered, in which the company has expanded to become practically the sole mine operator and the community has grown from a small mining camp to the status of a modern city, there has been no shortage of water or any outbreak of water-borne, epidemic disease.

Jan 1, 1938

By Frederic P. Dewey

The improvement in leaching introduced by the Russell process has stimulated the development of processes for refining lixiviation-sulphides. In the early days several processes for dealing with the sulphides were proposed, and some of them were tried more or less ; but the business finally settled down to sending the sulphides to the smelters, although this was known to be both troublesome and expensive. In 1891 Mr. C. A. Stetefeldt* introduced at the Marsac mill, Park City, Utah, an unpatented process, built up out of the general fund of information available. It consisted in matting the sulphides, grinding, roasting, grinding again, and dissolving the copper out in diluted sulphuric acid, then melting the silver and crystallizing the bluestone. It did not yield fine bullion, hence the bullion had to be refined as well as parted; besides, there was some loss. This process was thoroughly tried at the Marsac refinery and then a year's run was made, the net result of which was that it did not prove sufficiently better than the sending of the sulphides to the smelters to warrant its substitution for that practice. In 1893 the Dewey-Walter Refining Company undertook the refining of the Daly sulphides in the Marsac refinery by the sulphuric acid process, upon which two United States patents ? have been issued to the writer. Naturally, difficulties were encountered in starting a new process, and most of 1893 was taken up in getting it into smooth working order; but in 1894 a run was started, in which all the regular sulphides produced by the

Jan 1, 1897

By Roy A. Hardy

THE Getchell mine is a comparatively recent discovery in the old Potosi mining district, Humboldt County, Nevada, a district organized in the seventies and eighties, in which some prospecting was done in several metamorphic zones along a monzonite-sedimentary contact. The district had no production in the early days and no further work was done until the same metamorphic zones were prospected for tungsten (scheelite) in 1917 and 1918, when a few small lots were shipped. It again lay dormant until 1934, when prospectors investigated a large siliceous escarpment at one end of the old district where outcroppings were a prominent feature of the topography. Undoubtedly, during the early prospecting of the district, the outcroppings had been investigated for mineral, probably by panning, with negligible results because the gold later found is invisible in the concentrate and is refractory. A fire assay revealed the presence of sufficient gold to warrant development work. The outcroppings were easily prospected by short tunnels having their portals in the siliceous material on the hanging-wall side, with a maximum distance to crosscut to the footwall of 135 ft., or a distance at right angle to dip of 60 to 90 ft. Development work, reaching a depth of over 600 ft. on the dip of the vein, was done by means of various crosscut tunnels, winzes and laterals. A churn-drill hole was also sunk, which intersected the vein at a depth of 1100 ft. on the dip. Sufficient development work of this character was completed by 1937 to justify the erection of a reduction plant to roast the sulphide ore and cyanide the calcine, and to treat the oxidized ore by straight cyanidation, to make a doré bullion for shipment to the mint. The erection of the plant was started that year and finished early in 1938, with a combined capacity of about 800 tons per day. It has operated continuously since erection and recently was enlarged to handle 1000 tons per day. The vein dips with the slope of the mountain, and by stripping the hanging wall the ore may be mined by power shovel for several hundred feet below the outcrop. Thereafter underground methods will be necessary.

Jan 1, 1940

By R. B. Woodworth

Discussion of the paper of R. B. Woodworth, presented at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2247 to 2312. R. B. WOODWORTH, Pittsburgh, Pa.-This is a very long paper. It is a structural engineer's contribution to the art of mining and is written from his standpoint rather than from that of the mining engineer, and is, therefore, a study in the development of drilling structures by one who has made it his business to design structures rather than mechanism and machinery and rather than to utilize those structures in the actual exploitation of oil and gas. Drilling practice varies widely in different oil and gas fields. The , problems of western Pennsylvania are much simpler than the problems of the Mid-Continent and of the Gulf Coastal Plain and these again are simpler than problems of the Pacific Coast. The history of the commercial development of oil and gas is recorded in the annual publications of the U. S. Geological Survey and other bodies whose business it is to make record of statistics. The mechanical and structural features of the art of drilling have not yet received adequate treatment by the historian. Scattered references may be found on the subject in almost any work dealing at large with petroleum and its production. These references, however, are to those particular aspects of the matter that were contemporary with the publications themselves, but so far as I am aware there is no continuous and comprehensive account written of the development of drilling structures from their beginnings down to the present time, and certainly the more modern application of steel in the construction of such structures has not previously had an adequate discussion. With this latter phase of the subject I have been intimately associated, indeed, taking to myself the credit for having, in a way, been responsible more than any one else in the United States for the application of steel in the manufacture of drilling structures, and the purpose of the paper which is now before you is to record particularly the steps in that development while the subject is still fresh and the data available.

Jan 5, 1916

By Wilbur T. Stuart

THE increased demand for iron ore has necessitated a re-examination of ore-bearing lands on which the presence of water previously has indicated hazardous and expensive operating conditions. In view of the importance of iron ore production to the national economy and defense, the Ground Water Branch of the U. S. Geological Survey, in cooperation with the state of Michigan, began a study of mine drainage in the Iron River district in 1945, and later extended the work to the Marquette district. The purpose of these studies was to define the principles involved in the movement of surface and ground water toward the mined areas, with the hope that the information obtained in the research would lead to the development of methods of water control and to a reduction in the total mining costs.

Jan 12, 1951

By E. B. Olds, Burt. B. P.

THE mines of the Consolidated Coppermines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. [ ] The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 1 ½ miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1946

By J. Moore Samuel

INTRODUCTORY BEFORE the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure, that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed "chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing the same, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 6, 1916

By R. J. Armstrong, J. J. McKay

The Montana Phosphate Products Co. is currently operating three underground phosphate mines in Powell County, MOnt. † In this area the Phosphoria formation is from 35 to 50 ft thick and contains a bed of phosphate rock varying in thickness from 2 1/2 to 5 ft, overlain by 12 to 30 ft of cherty quartzite, and underlain by about the same thickness of quartzite and shaly to cherty beds. In general, the phosphate bed has a reasonably hard quartzite footwall, as well as a hard cherty hanging wall, both of which greatly facilitate the mining operation. Folding has deformed the phosphate bed to a considerable degree in the area. It is carried to surface by several of the anticlines and lowered to considerable depths in some of the syn-clines. The main structural features affecting the mining operations of the company are the Garrison anticline and the adjoining syncline and succeeding limb of a second anticline on the east (Fig I). The axis of the folding strikes roughly northwest-southeast. The three mines, namely, the Anderson, Graveley, and Luke are on different limbs of the above folds. Accordingly, the dip of the bed, and consequently the mining method, in each mine differs to a considerable degree from that of the others. For this reason, each operation will be dealt with separately. Anderson Mine LOCATION AND DEVELOPMENT Topographically this mine is in a narrow valley, the bottom of which has an altitude of 5200 ft. The phosphate bed outcrops near the ridge on the east and dips towards the valley floor at an angle of from 25 to 30°,

Jan 1, 1950

By Worthen Bradley, R. G. Hall

THIS paper will attempt to show how a metallurgical problem at one California quicksilver mine was solved, and how the solution was applied successfully at another mine. The pronouns "we" and "our," as used below, refer to the Bradley Mining Co. of San Francisco. The term "concurrent firing" for the purpose of this paper can be defined as feeding and firing a rotary kiln at the same end-that is, of course, the upper end. This is as opposed to "counter-current firing," the orthodox method, in which a kiln is fed at the upper and fired at the lower end. The terms "quicksilver" and "mercury" are used interchangeably. EARLY REFERENCES The earliest work on nonferrous metallurgy, we believe, was The Pirotechnia of Vannocio Biringuccio,1 its first edition having been printed in Italy in 1540. Quoting from its chapter entitled "Concerning Quicksilver and Its Ore": Quicksilver . . . is one of the gods and has divine strength in itself, and also, to the annoyance of the alchemists, it is winged. Hence, when it sees that it is in gravest danger, it loosens itself from . . . every bond . . . and flies away into the heavens, escaping from the hands of those who crucify it. Almost laughing, it leaves all its adversaries mocked and scorned, with their phials and filters empty . . . How thorough a job, under certain conditions, it can do of mocking its adversaries and leaving their phials and filters empty, was found out four centuries later at the Sulphur Bank mine, on the east shore of Clear Lake, in Lake County, California. The other mine mentioned in the title is the Reed, in Yolo County, California, 35 miles by road southeast of Sulphur Bank. Reed and Sulphur Bank ranked respectively fifth and seventh in U. S. production in 1943. The earliest direct reference we can find to furnacing troubles at these mines was by Thomas Egleston in 1890.2 Speaking of Sulphur Bank, Egleston says: Sometimes there is more sulphur than cinnabar in the ore, which is a detriment to both . . . making the sulphur impure, and rendering the cinnabar difficult to work on account of the soot. In some of the early . . . furnaces the accumulation of soot from the excess of sulphur has been known to penetrate as far as the fan blower at the end of the . . . condensers, and completely prevent its revolution. In order to get rid of the inconvenience of this accumulation . . . , as well as to get a commercial value from the sulphur, it (the sulphur) is now separated by steam and sold. It is claimed that the sulphur alone pays all the expenses of . . . the mine. The mine was first worked for sulphur, and the cinnabar it contained was considered to be an inconvenience, and was carefully picked out and thrown away. as its richness and value were not

Jan 1, 1945

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

By William Mikulas Lars Thomassen, Clair Upthegrove

Little work has been done in the field of the nickel-tin binary system. The complete diagram has been investigated on two occasions, but the results are in very poor agreement. The structure of a compound NiSn and the solubility of tin in nickel have been determined by X-ray methods. Several investigations have been made of the liquidus curve, and the compositions of the eutectics have been determined. A study of the literature, however, shows that there is no satisfactory agreement between the data presented in the various papers. The present investigation was undertaken in an attempt to determine the equilibrium conditions, and to correlate X-ray with metallographic data. The equilibrium diagram was determined by thermal and metallographic means, and the solubility of tin in nickel further investigated with X-rays. Powder diagrams were made of the intermetallic compounds, and three of the structures were partly determined. NO attempt was made to determine the range of homogeneity of the intermetallic compounds. Review of the Literature Vigorouxl prepared alloys of tin and nickel containing 74 and 92 per cent of tin. By treating these alloys with very dilute nitric acid or with sodium hydroxide he was able to separate residues, both of which analyzed 66.7 per cent tin. This corresponds to the compound NiSn and was reported as such. Guillet2 made the first investigation of the complete binary diagram Fig 1) The maximum point of the liquidus is at 43.5 per cent nickel. Several solid solution areas were found, and the compound NiSn was included on the strength of Vigoroux's work. The investigation was

Jan 1, 1937

By Fred A. Krafft

The time allotted to this paper will permit only the sketching of general principles and practice as generally employed in the industry to maintain and preserve the physical well-being of the miner and his family. Let it be emphasized on behalf of the industry that coal opera- . tors, individually and collectively, have given primary consideration to the appointment of a mine or community physician who is charged with the responsibility of caring for the sick and injured. However, it too frequently happens that with the selection or appointment of the camp doctor many operators wash their hands of further responsibility toward the health and the working efficiency of their employees. The coal industry is so organized in most of the coal-producing areas that not only is the health of the individual miner an important production problem but the collective health of the entire mining community is a fundamental operating problem. This is particularly demonstrated when epidemics of communicable diseases attack entire communities, with resultant loss of life and production and general community distress. The problem and responsibility of maintaining high health standards among miners and their families should be given as much consideration as safety, economical production and efficient distribution are given in the successful operation of coal mines. Company Policy In the inauguration or administration of a medical program for a large mining operation or for an individual mine, the first question to be solved is what the company policy is to be with respect to the following factors pertinent to a medical program: 1. On what basis will the company and the employees finance the program ? 2. Should a contract doctor or a full-time doctor on salary be employed ? 3. What measure of service is to be rendered the employee and his family in return for his monthly contribution to the medical program?

Jan 1, 1936