Search Documents

By M. N., Short

TIE Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a confused series of mountain ranges of moderate FIG. I.----SUPERIOR, LOOKING NORTH FROM SOUTH BANK OF QUEEN CREEK. MAGMA MINE IS INDICATED BY WASTE DUMP IN GULCH TO RIGHT OF CENTER. height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County.

Jan 2, 1926

By I. Cornet

INTRODUCTION WITH the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943 1; it has been released for publication by the O.S.R.D. SCOPE OF THE INVESTIGATION The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with the notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and M. For comparison, extrusions of aluminum alloy 24S-T, cast bars of aluminum alloy I22-T2, and cast bars of magnesium alloy C were also tested, The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of the tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the changing hardness, tensile strength, microstructure, and notch sensitivity observed. EXPERIMENTAL TECHNIQUES AND PROCEDURES Tensile Testing Bars used for axial loading were machined with 3/8 in.- and with 1/4-in. minimum diam, and included specimens with 6o° V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These V-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1948

The engineering personnel shortage, present and impending, so well brought out in the article in Mining Engineering in the August, 1951 number, both in the editorial lead and the article by William B. Plank and Henry J. Petrie, has left untapped and has ignored a potential source of supply that would fill the need ably and with complete satisfaction. This source is comprised of the women engineers- and geologists, both presently, trained and able to handle work at all levels, and the many who would make splendid engineers and geologists if they could hope for even a modest taste of the square deal that should be theirs, but, as we all know, is not. I write from experience. It is not pleasant or sensible to have to urge borderline cases among men students to consider engineering and geology as careers to fill the need, when I have far more able, interested and suited young women students whom I must divert into other channels. It does not make sense to scrape the bottom and sides of the barrel to induce potentially second or third rate male engineers and geologists to enter the profession when we have superior material among the women, eager to do good work in these fields. It does not make sense for these men to become second or third rate in these fields when they might be first rate salesmen, musicians, advertising copywriters or policemen. Nor does it make any more sense to force potentially first rate female geologists and engineers to become second or third rate and very frustrated typists, kindergarten teachers, dress sales-women or clerks. At this point I am willing to admit that where superstitious -miners object to women in underground workings, men are available for the jobs. Moreover, it is not necessary for women to be sent into the most difficult country, if there is reluctance on either side of the contract. There may be fewer of them eager for the roughest assignments, in proportion to the men, but women are so accustomed to discrimination far more complete than that against any racial or religious group, that a reasonably tough assignment would seem like a heaven-descended joy. In my own experience, I have found that my girl students majoring in geology, could keep up with me in the field in the roughest terrain, but. the men, all but the best students and the most physically fit young men, complained that they could not keep up with me and that I always "walked their-legs off. The women, a few men and I always returned with bags heavy with well chosen specimens and proper notes. Most of the men carried no specimens and-but poor scraps of notes on loose bits of paper. Yet the men were urged to prepare for a career in engineering or geology if their examination marks were reasonably good. When we find that we still have a shortage of engineers and geologists, after putting all the qualified women to work, then we may begin to worry. Until then, we are simply fooling ourselves as we wander in, a forest of outmoded tradition and emotional habit reactions. MARY W. GARRETSON ASSOC. MEMBER, AIME SCARSDALE, N. Y.

Jan 1, 1952

By A. J. Stosick, J. R. Hoffman, E. Rudy, St. Windisch

The binary alloy system Mo-C zoas investigated by means of X-ray, metallog/aphic, thermoanalytical, and melting-point techniques on chemically analyzed specimens. The system, Fig. 39, is characterized by three congruently melting, intermediate phases, Mo2C, n MoCi-x, and aMoC1-,, of which only Mo,C is stable at temperatures below 1650°C. Substoichio-metrzc (~32.5 at. pct C) dimolybdenum carbide undergoes a homogeneous sublattice order-disorder transformation at temperatures of approximately 1400°C, whereas hyperstoichiorrletric compositions undergo a discontinuous Phase change. The order-disorder transitions in the Me, C phases are discussed in terms of the structural changes involved in the transformation processes and the absence of long-range sublattice coherency in stoichiometric or hyperstoiclziomet-ric compositions attributed to the impossibility of obtaining long-range order in a linear chain of alternating carbon atoms and vacancies. From the experimental phase relutionships and the known thermody-namic data for Mo2 C, limits for the free energies of formation for the high-temperature phases r) MoC1-, and aMoC1-, are deriued and found to be in good agreement with data previously obtained from phase equilibria in ternary metal-carbon systems. IN the course of studies of the high-temperature phase relationships in ternary systems of refractory transition metals with carbon,' a number of inconsistencies found in previous work necessitated a reex-amination of some of the related metal-carbon binaries. A reassessment of the binary system data also seemed

Jan 1, 1968

By Alfred Weiss

Over the past 25 years hard-rock mining companies have developed a number of profitable computer applications which appear applicable to operations in the coal industry. The evolution of these applications are described and the most profitable discussed. The basic nature of these systems is that they must cut across organizational boundaries. While technological advances contributed significantly to the successful implementation of computers within mining, the human aspects related to organization, management and control of systems projects remain as key to future success in coal as they were and still are in hard-rock mining.

Jan 1, 1983

By Charles F. Johnson

A pulse technique is described for the measurement of bar velocity. A low frequency sine wave pulse is used which allows the wave-length to become much larger than the lateral dimensions of the test specimen. The low frequency pulse method has been tested and compared with the resonant frequency method and the results show that both methods give, on the average, equivalent velocities.

Jan 1, 1971

By Thomas T., Read

TWO American students entered the Ecole des Mines in 1856, Joseph Lesley of Philadelphia and Thomas Egleston of New York. Lesley remained there only one year, but Egleston completed the whole 'curriculum and received, in 1860, the certificate given to foreign students .in lieu of the official appointment and degree. awarded French students. Returning home he received, in 1861, an appointment by Secretary Henry of the Smithsonian Institution to sort, label, and arrange the collections of mineralogical and geological specimens which had been brought to Washington by the various government exploring expeditions in the West. Thomas Egleston, born in New York City on Dec. 9, 1832, was the son of Thomas Jefferson Egleston, who came to New York from Massachusetts some time before 1829. The first American ancestor of the family had settled near Dorchester. in 1630. T. J. Egleston and Joseph Battell established an iron-merchandizing business* at 166 South St., New, York, which prospered exceedingly; so much so that when Thomas J. Egleston died, July 12, 1861, his estate had a book value of over $500,000. Since an older brother was expected eventually to take over this business, Thomas, who had a liking for science, went to Yale,, where he completed the regular four-year course in 1854, and then remained another year for advanced work in chemistry under Silliman. I One biographer says he went to Europe, . early in 1-856, on account of his health. It was the custom at that time for wealthy young men to make a tour of Europe after completing their academic education. Whatever the precise reason, he began scientific work at the Jardin des Plantes in Paris but soon trans* It still operating as Egleston Bros. Inc., though no direct descendants of its founder are now living.

Jan 1, 1941

By D. B. Gillies

IN 1938 the Republic Steel Corp. announced that it had leased the ore mines and other property of the Witherbee Sherman Corp. at Port Henry, N. Y. The announcement brought forth an interesting reaction. Two questions were asked repeatedly: (1) Is the iron product high grade? (2) Is there a substantial reserve? The answer to both questions was and is a decided and emphatic "Yes."

Jan 1, 1943

By Alan D. Hoagland

The Flat Gap mine, are important zinc deposit of the Appalachian type, is located in the Copper Ridge Belt in the Valley of Tennessee approximately 30 miles northeast of the Mascot-Jefferson City zinc district (Fig. 1). The ore is found in large stratigraphically linked deposits in solution and collapse breccias of the Kingsport, Longview and, to a minor extent, Mascot formations of Lower Ordovician age. The principal ore mineral is sphalerite and the principal gangue minerals are dolonmite and accessory pyrite. There is local minor galena and very rare barite and fluorite.

Jan 10, 1962

By William N. Poundstone

To forecast the future of coal intelligently, one must first consider the market outlook. Coal can be used for many purposes, but currently about 25% of it goes into metallurgical coke, while 75% serves as fuel. Coal for metallurgical coke should show a modest growth for at least the next decade, primarily because of increased exports, but the important factor in the coal outlook is energy. Today, this country faces a serious shortage of energy, and its requirements are growing at an almost unbelievable rate. Last year the United States consumed 68 quadrillion Btu, or double the energy it consumed in 1950, and, if projections are correct, this figure will grow to 150 quadrillion Btu by 1990. Thus, in one working lifetime, the nation's energy consumption is expected to increase by roughly five times. The future of coal hinges on its degree of participation in meeting this energy need. The Federal Power Commission predicts that coal consumed by electric utilities will increase about 4-576 per yr, reaching 472 million tons by 1980 and 615 million tons by 1990. If this projection proves correct, 1980 consumption will be double that of last year and, even more startling, the utility industry alone will use more coal in 1990 than the entire coal industry produced in 1970. This is a tremendous increase, but in view of the projected energy growth, it is difficult to see how this country's needs can be satisfied with- out a coal contribution of this magnitude. Unless some new source such as solar energy is discovered, it must be assumed that the projected energy will come principally from the present-day sources-oil, gas, nuclear materials and coal.

Jan 1, 1971

By S. S. Clarke

THE opening of zinc-lead ore bodies in the lower chert beds of the Tri-State district, locally called sheet-ground deposits, [ ] presented several new economic operating problems to be solved before the low-grade deposits could be mined profitably. Drilling was the first high-cost problem and loading and haulage difficulties followed. At this time, the sheet-ground mines are producing about 2000 tons per day. GEOLOGY The geology and ore deposits of the Tri-State district have been covered in detail by [ ] Fowler and Lyden.* Briefly, the sheet-

Jan 1, 1942

By Luis Toron, Salvador Cortes-Obregon

THE Oaxaca coal fields, shown in Fig. 1, are located in the Alta Mixteca region in the states of Oaxaca, Puebla, and Guerrero. Known outcrops are scattered over 3125 square miles. It is probable that further exploration will reveal a more extensive area of deposits. The region is of great importance to Mexico, as at present the only sources of coal are the fields near the U. S. border. Steel mills are also located in the North, and finished products must travel 600 to 800 miles to the area of consumption in central Mexico. The oaxaca coal, only 120 miles south of Mexico, D.F., lies close to several iron ore deposits. If this

Jan 1, 1955

By Knut L. Sandvik, Aage Solbakken

it is an established fact that the collecting properties of xanthates and anionic collectors are dependent on the hydrocarbon chain length. This is ascribed to the greater adsorption densities caused by increasing the xanthate chain length. As batch flotation tests showed similar trends for amines, an investigation of the adsorbing properties of amines was undertaken. Because earlier investigations showed adsorption densities for dodecylamine salts on quartz varying as much as 20 times under apparently similar conditions,1-4 it was decided to make a survey of the changes in adsorption density due to the drying conditions of the quartz. EXPERIMENTAL PROCEDURE The quartz, handpicked in the pegmatite quarries of Iveland, Setesdal, had the following composition: SiO2 99.81, A12O3 0.01, Fe2O3 0.05 and loss by ig-

Jan 1, 1969

By K. Winterton

The effect of a near-saturation unidirectional magnetic field was to decrease slightly the endurance life in Armco iron in the annealed condition. This is expected since the energy-absorbing mechanism associated with domain wall movemenfs is inhibited bv the strong field. THE factors determining failure under dynamic loading are not yet clearly recognized. One of the properties of a metal which might be thought to influence fatigue life is its damping capacity. Foppl1 conducted an alternating torsion test at a frequency of 700 cpm continuously for a period of 3 years, without the test piece breaking or showing any sign of deterioration after 1100 Million cycles of stress; the rate of dissipation of energy was sufficient to maintain the test piece at about 100°C above the ambient temperature. cazaud2 concludes from this, and others follow him, that ('the capacity for dissipation in the form of heat by internal damping is unlimited" and that therefore "damping is not directly related with fracture by fatigue." Future work may necessitate qualification of this rather uncompromising view. It is shown later that in all

Jan 1, 1960

By W. R. Ingalls

ThE following chronology presents the history of lead-mining in the United States in a brief form and is a useful reference in connection with the statistics of production: 1621.. Lead was mined and smelted near Falling Creek, Va., to supply the local demand for bullets and shot. This was the first mining and .smelting of lead in what is now the United States. 1632. In a report made on the minerals of New England, lead-ore is mentioned. (Bishop, I., 470.) 1650. Supposed beginning of mining by Jesuits in Pima county, Ariz. 1651. Grant of lead-mine at Middletown, Conn., to Gov. John Winthrop. 1682. Lead-ore supposed to have been discovered in Wisconsin by Nicholas Perrot. (K. D. Irving, Mineral Resources of Wisconsin, Trans., viii., 498.) 1700 Discovery of lead in Missouri by Penicaut, one of Le Sueur's party. Tile same expedition discovered lead near the southern boundary of Wisconsin in August of the same year. 1712. Grant by Louis XIV. of the Crozat patents, with special privileges respecting the discovery and operation of mines in the then territory of Louisiana. Little or no mining was done under this patent until about 1720. 1717. Transfer of Crozat patents to the Mississippi Co., promoted by John Law, which prepared for active mining. 1719. First attempt to mine and smelt lead in Missouri, made by Sieur de Lochon, in behalf of the Mississippi Co., near Meramec river. Results unsuccessful.

Jan 1, 1908

By Mrs. V. J. DeCarlo, G. P. Salvo, H. W. Schadler, L. M. Osika

The lattice parameter of the inlerrnetallic compound Nb3Sn has been measured as a function of temperature from 80° to 1290°K. The results are compared with published data on the thermal ex- ThE recent interest in the intermetallic compound, Nb3Sn, as an engineering material for the production of superconducting devices has necessitated that certain engineering data be obtained. Because of the difficulty encountered in producing bulk pansion of niobium and indicate that the compound when made by diffusion of tin into niobium at 1000°C, would be subjected to a tensile strain of about 0.1 pct when cooled to room temperature. material which is single phase, the coefficient of thermal expansion has not been measured by dilata-tional methods. Therefore the lattice parameters of fine-grained samples of Nb3Sn produced on the surface of a niobium sheet by heating in molten tin at 950°C have been obtained as a function of temperature. The results are compared with published data on niobium2 and Nb3Sn3 and with lattice-parameter measurements made on small single crystals of Nb3Sn.

Jan 1, 1964

By Theodore B. Comstock

a. Boundaries of the District.—The district here considered comprises that portion of Colorado commonly known as " the San Juan Country." In order to bring the principal geological features of this region within the scope of a map of convenient dimensions upon a suitable scale, I have found it desirable to mark off boundaries near the parallels of 37O and 38O 10', and the meridiaus of 106' 30' and 108' 30' (West Longitude from Greenwich). This area of (approximately) 9400 square miles includes all the formations which we should have to discuss if our territory were greatly enlarged, excepting such as are distinctly characteristic of adjoining areas with independent orographic genesis. By limiting this review to these confines we miss very little of the geology of the eight counties of the San Juan region, viz.: Dolores, San Miguel, Ouray, Hinsdale,

Jan 1, 1887

By J. F. Kemp

PAGE Introductory Description of Deposits of this Type,.....244 Topography of the Ducktown Region,...247 Geology and Petrography,...248 The Mineralogy of the Ores and Gangue,..249 The older minerals : Amphibole, 250 ; Pyroxene, 250; Garnet, 251; Zoisite, 252; Calcite, 258 ; Quartz, 259 ; Apatite, 259 ; Rutile, 259. The Sulphides: Pyrite, 259; Zincblende, 259; Galena, 260; Pyrrho tite, 260; Chalcopyrite, 260. Later minerals, not belonging to the Gossan: Quartz, and certain sul phides, 261 ; Graphite, 261. The Formation of the Ore,...262 The Gossan Minerals,...........263 Bibliography,............265 Introductory Description of Deposits of this Type. Ore-bodies of more or less lenticular shape and lying parallel with the foliation of schists and slates form a group of

Jan 1, 1902

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins' and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer' type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964