Search Documents

By H. F. Dunlap, R. R. Hawthorne

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By R. R. Hawthorne, H. F. Dunlap

A method of calculating formation water resistivities from chemical analyses is presented which is somewhat faster and more accurate than previously described methods. For 26 formation water samples taken from wells in the Texas Gulf Coast, the average deviation of calculated from measured water resistivities was 3.3 per cent, with an average bias of + l.l per cent in the calculated values. This compares with average deviations of 4.6 per cent and 7.8 per cent, with corresponding average biases of +3.2 per cent and -6.3 per cent, for the two methods previously described in the litera-

Jan 1, 1951

By H. A. Bauman, T. S. Spicer, C. C. Wright

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 2, 1950

By Herbert Lang

Cord-wood, sawn into blocks of about a foot in length, is a regular constituent of our fuel-charge at Mineral, Idaho, our work being the matting of silver-ores by fusion in a blast-furnace. The furnace is a round water-jacket furnace, of 36 inches diameter at the tuyeres, and the charge of smelting-mixture weighs 950 Ibs., requiring 110 Ibs. of Connellsville coke to drive it. I replace half this coke with 135 lbs. of fir-wood, cut from dead and apparently perfectly dry trees. This mixtrire produces as high a sn~elting-temperature as all coke, whence I infer that the smel ting-effeot of a given weight of wood is to that of the same weight of coke as 11 to 27, or 1 to 25/11. A cord of wood sawed ready for use weighs 2840 lbs., costs $5.00, and is

Jan 1, 1892

By W. C. Lacy

This article is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The author feels that, although there does not appear to be any one technique or characteristics that will suffice as an index to the determination of stable slope angles, a combination of seismic methods as outlined here, detailed geological mapping and logging of core, and a better understanding of the angle of internal friction in rock types will permit accurate estimation. A mining engineer friend once remarked, "If we don't have pit slope failures, the slopes are too flat." Since economic justification of an open pit project is based upon ultimate pit slopes, we cannot wait until the pit is developed and slopes established by trial and error. Some combination of geological and/or geophysical techniques must be developed to permit accurate prediction of stable slope angles and to suggest modification of pit outlines to result in slopes enabling maximum economic yield. This presentation is a progress report of a program designed to quantitatively evaluate geological parameters to predict stable slope angles. The principle of the weakest link applies to any slope stability evaluation and necessitates detailed geological examination and recording of observations. Physical failure will occur along any surface where shearing stress exceeds shearing resistance. Rock conditions are seldom uniform even within a single cut or pit face, so stability conditions will vary. Consequently, both plan outline and ultimate slope limits must be tailored to the specific situation. Economic advantages to be gained by slight increases in slope angles in deep pits are well recognized and stimulate efforts to obtain maximum permissible slope angles. MECHANICS OF SLOPE FAILURE Excellent reviews on the nature of slope failure have been presented+2,6,8,11 For the purpose of this study, the writer considers failure to take place by one or more of three processes: 1) ravelling, 2) translation or slope failure, and 3) rotation or base failure (Fig. 1). The effects of increased pore water pressure in soils were recognized in 1923 by Terzaghi in his development of the concept of effective stress, and he has applied the same principle to jointed rocks designating water pressure as cleft-water pressure.8 Cleft-water pressure in a rock slope reduces normal pressure on the plane of failure, thus reducing shearing resistance and resulting in slope failure. In the following discussion it is assumed that adequate drainage is supplied to prevent any build-up of water pressure. This is the first step in any program to establish maximum slopes. Ravelling: Ravelling occurs in rocks with low cohesion and entails the free movement of individual fragments ranging from single rock falls to running ground. Removal of lateral support wherever slope angle exceeds the angle of repose of the rock parti-

Jan 1, 1963

By Roy R. Weil, John A. Dziubek

This paper discusses the use of computer modeling, data manipulation, and mapping of three multi-seam coal properties in the Appalachian coal basin. Each case history represents a slightly different application of computer usage for estimation of reserves and planning surface mine sequencing. This practical use of computers demonstrates the suitability of data processing for normal evaluation of coal properties.

Jan 1, 1983

By James L. Kelly

Stripping of the Twin Buttes copper deposit started in 1965. Total material removed for the first 10 yr of operation is approximately 879 million tons. The sulfide concentrator has treated about 45 million tons. The Twin Buttes mineral zone was concealed under several hundred feet of recent alluvium. Beneath this post-minera1 cover, Paleozoic limestone, siltstone and quartzite, and Mesozoic metaarqillite, arkose, conglomerate, and volcanic rocks are intruded by an igneous complex of quartz monzonite and diorite. All rock units are erratically mineralized, principally with copper and molybdenum. Strongest copper mineral favors the Paleozoic calc-silicated limestone and siltstone, often preferential to individual beds.

Jan 1, 1978

Page McGREGOR, A. G.-Features of the New Copper Smelting Plants in Arizona. Discussed by L. D. Ricketts, E. P. Mathewson 2145 HOWARD, L. O.-The Basic-Lined Converter in the Southwest. Discussed by Walter Douglas, E. P. Mathewson, Kuno Doerr 2145 SAMUEL, J. MOORE-Determination of Dust Losses at the Copper Queen Reduction Works. Discussed by Walter Douglas, E. P. Mathewson, S. J. Jennings, C. E. Arnold, A. G. McGregor, L. D. Ricketts 2148 MORSE, H. W., AND TOBELMANN, H. A.-Leaching Tests at New Cornelia. Discussed by H. W. Morse, Lawrence Addicks, G. D. Van Arsdale, S. J. Jennings, F. S. Schimerka, C. G. Grabill, F. N. Flynn, Stuart Croasdale 2151 LAIST, FREDERICK, AND ALDRICH, HAROLD W.-The 2,000-Ton Leaching Plant at Anaconda. Discussed by F. N. Flynn, E. P. Mathewson 2159 ADDICKS, LAWRENCE-Possibilities in the Wet. Treatment of Copper Concentrates. Discussed by F. N. Flynn 2160

Jan 12, 1916

By Dean W. Lynch

Arizona: The San Xavier Indian Reservation mine is located approximately 2 ½ miles northwest of Asarco's Mission Mine southwest of Tucson. The company plans to produce oxide and copper-bearing siliceous ore at this operation, construction of which is scheduled for completion in 12 months. Asarco also plans a copper leaching and iron precipitation plant at its mine. The plant will leach 4000 tpd of oxide ore using sulfuric acid produced at the company's acid plant now under construction at Hayden. Copper precipitates will go to the smelter at Hayden. A drilling program at the Sacaton copper prospect in Pinal County, has disclosed two porphyry copper deposits. One deposit, mineable by surface mining, has approximately 17 million tons of material averaging 0.80% Cu. A deeper deposit suitable for under- ground mining has approximately 12 million tons averaging 1.5% Cu. Although Asarco intends to place this property in production, no startup date has been determined.

Jan 1, 1970

By H. O. Hofman

PAGE I. Introductory,.......... 258 11. Condensed Account of Past and Present Plants,. .. 259 111. The Ores. Table I., Average Analyses,..... IV. Metallurgical Treatment—Roasting OF Ores,... The Allen-O'Hara Furnace,....... The Wethey Furnace,........272 The Pearee Turret-Furnaces,....... 273 The MacDougall Furnace,.......275 Original MacDougall,.......276 Herreshoff,......... Evans-Klepetko,........ General Results (Table II.),.......282 V. Smelting Ores in The Blast-Furnace,...,. Table 111. Examples of Montana Blast-Furnace Smelting,. 284 Table IV. Analyses of Coke and Coke-Ash,. .. . VI. Smelting Ores in the ReveRberatory Matting-Furnace,. 289 Table V. Percentage of Components of Charge,. .. 290 Table VI. Analyses of Flue-Dust and Briquettes,. .. Table VII. Examples of Montana Reverberatory-Smelting,. 292 Table VIII. Analyses of Coals,...... Table IX. Analyses of Producer-Coal and Ash,. .. Details of Practice,........297 VII. Converting Coppr-Matte,....... 302 Table X. Analyses of Materials of Converter-Linings,. . 306 Table XI. Montana Converters,......308 Yield of Metal..........308 VIII. Electrolytic Refining of Copper,..... Refining of Cathodes,........ 313 Table XII. Details of Electrolytic Refineries,. .. . Table XIII. Efficiency of Some Rocky Mountain Coals,. . 316 I. Introductory. In 1901,* this country produced 268,782 long tons of fine copper. Of this total, Montana is credited with 102,621 long tons, or 38.2 per cent.

Jan 1, 1904

By David, Levinger

THESE observations of the metal-working industries of Europe are based on a three months' tour of eight countries of Europe, in which 75 industrial establishments were visited in England, France, Germany, Belgium, Holland, Italy, Austria and Switzerland during the summer of 1927. Since the Western Electric Co. is a large consumer of copper and brass, these industries were of particular interest and differences in practices were of keen interest to us.

Jan 1, 1928

By J. J. Scott

During 1967 wage settlements and strikes ran at a high rate and it has been estimated that union gains of 4 ½ % to 5% per year have been attained in many instances. When these events are coupled with the need to operate on lower grade and deeper deposits the need for technological advances in underground mining becomes obvious. Emphasis has been on ways to reduce the number of manshifts required per ton of product. Most significant advances have been made in rapid advance of primary mine openings, development of mobile, rubber-tired, front-end loaders and hauling units, high-speed drilling with rotary and rotary percussive units and a serious look at nuclear devices to break large volumes of ore cheaply. Boring Developments in bit manufacture and metallurgy have allowed continuous boring-type machines to be used on harder formations than was deemed feasible in the past. Hecla Mining Co. has been using raise boring equipment for drilling 9 7/8 in. diam pilot holes in raises which are later reamed in an upward direction to 48 in. diam. The machine used is a J. S. Robbins model 42R raise borer which has been used successfully to drill two relatively long 48-in. diam holes. The first was 520 ft in length at a dip of 76º, and the second was a 785-ft vertical hole.

Jan 2, 1968

By Harold J. Bennett

A comprehensive knowledge of the availability of mineral resources to evaluate and assure a dependable supply is a prerequisite in establishing and maintaining a viable national economy. Since no nation is self-sufficient in all its mineral needs, its prosperity depends to a great degree upon its developing and maintaining an effective national minerals policy. This must be preceded by a systematic inventory of mineral resources that may be available to that nation. The U.S. Bureau of Mines is implementing a mineral deposit inventory program of domestic and foreign mineral occurrences, with initial emphasis on the domestic. In order to provide an in-depth appraisal of minerals availability, the approach includes not only realistic estimates of quantity and quality, but other essential factors such as costs, technology, environmental constraints, and development-time requirements. Analysis of this information provides usable relationships of quantity, price, time, and associated degrees of confidence of the occurrence of identifiable mineral resources. Keeping pace with a changing minerals industry and handling the large volume of information required in this undertaking demands that computer methods be employed.

Jan 1, 1977

By Charles R. Holmes

MORE than 70 igneous pipes and dikes are known to occur in Cambrian sediments throughout an approximately circular area of about 75 sq miles, in southwestern Ste. Genevieve County and southeastern St. Francois County, Mo., across the southern portion of the Farmington anticline, which is outlined in fig. 1. From evidence obtained from fossil fragments taken from some of the intrusives, and from the similarity in composition of the more basic intrusives to those of known age in surrounding states, these pipes and dikes are believed to be at least post-Devonian and probably Cretaceous in age. As first postulated by Rust[1], these intrusives are believed to represent explosion tubes, or diatremes, punched through great thicknesses of solid rock by gaseous pressure.

Jan 11, 1950

By AIME AIME

General Local Committee.-John Fritz, Chairman; A. B. de Saulles, Vice-Chairman.; R. M. Bird, Treasurer; Henry S. Drinker, Secretary; Robert H. Sayre, E. P. Wilbur, Charles M. Dodson, Abraham S. Schropp, E. M. McIlvain Archibald Johnston, A. B. Fichter, C. G. Convers, W. A. Wilbur, Garrett B. Linderman, Frederick Conlin, George Pettiuos, Albert Brodhead, Garrett L. Hoppes, M.B. Cutter, H. J. Seaman, C. A. Matcham, B. F. Fackenthal, Jr., A. L. J. Queneau, Geo. R. Elder, Eldridge Wilbur, William H. Chandler, Mansfield Merriman, Joseph F. Klein, William S. Franklin, William Esty, Joseph AN'. Richards, Howard Eckfeldt, John D. Irving. Transportation Committee.-H. J. Seaman, C. A. Matcham, B. F. Fackenthal, Jr., A. B. Fichter, A. L. J. Queneau, Henry S. Drinker. Hotel Committee. -Garrett B. Linderman, Charles M. Dodson, W. A. Wilbur, Garrett L. Hoppes, Albert Brodhead. Steering Committee.-William S. Franklin, William Esty, John D. Irving, R. M. Bird, the members of the Tau Beta Pi Society of Lehigh University. Committee on Meetings - William S. Drinker, Joseph W. Richards, Howard Eckfeldt. Entertainmment Committee.-W. A. Wilbur, E. M. McIlvain, Archibald Johnston, A. B. de Saulles, G. G. Convers,.A. L. J. Queneau, Garrett B. Linderman, Frederick Conlin, George Pettinos, Garrett L. Hoppes, Henry S. Drinker, William S. Franklin, Eldridge Wilbur, Robert M. Bird, Secretary. The opening session was held at 8.30 p.m., Wednesday, February 21, 1906, in Gymnasium Hall of Lehigh University, which had been tastefully decorated with flags and bunting. Dr. Henry S. Drinker, President of Lehigh University, and Secretary of the General Local Committee, called the meeting to order, and welcomed the Institute to the Bethlehems, where its first meeting, after its organization in May, 1871, at Wilkes-Barre, was held in August, 1871.*

May 1, 1906

By Garth M. Crosby

Seven mines with important production records in the Coeur d'Alene lie adjacent to the Gem stocks -the Frisco (Gem), Hercules, Interstate, Rex (Sixteen to One), Success (Granite), Sunset, and Tamarack. Old records are incomplete, but avail- able data given in Table I show these mines have produced 10,550,721 tons of ore containing more than 50 million oz of silver, more than 1.5 billion lb of lead, and about 1 billion lb of zinc (approximately 1.25 million tons of lead and zinc combined). Average ore grade is 4.8 oz of silver per ton, 7.2 pct Pb, and 4.6 pct Zn. This impressive production represents about 12 pct of the District's yield. At present metal prices, with modern beneficiation, the gross value would be more than $400 million.

Jan 7, 1959

By E. B. Ekren, F. C. Frischknecht

Recently released results of surveys employing the slingram and turam methods show the applicability of electrornagnetics in mapping new areas containing both oxidized and unoxidized iron in the Lake Superior region.

Jan 10, 1961

By J. M. Mutmansky, T. K. Greer

This paper takes a look at the optimal velocity to be used in coal mine entries and determines a statistical relationship for optimal velocity that can be applied under current mining conditions. This relationship provides the optimal velocity for coal mine airways under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. This enables the ventilation engineer to make an easy, rapid determination of the optimal velocity for planning purposes.

Jan 1, 1985

By N. D. Policow, J. S. Orphanos

Dewatering fine clean coal fractions, -595µm (-28 mesh), represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the screen bowl centrifuge has offered an economical alternative to filtration/thermal dyer combinations. The performance of screen bowl centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Test comparisons with alternative methods show the screen bowl centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1984

By L. E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more TiO2 than the formula FeTi03 would indicate, and some Fe2O3. This variation in composition is due to different amounts of altered ilmenite in the concentrates. (') The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amaphous or very finely crystalline titanium dioxide and ferric oxide. Other studies(2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal pr0cesses.(3,4,5 Three main methods of approach were used to study the mechanism and rate of ilmenite weathering. (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived. (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions. ETCH FIGURES ON ILMENITE CRYSTAL PLANES A rather large ilmenite crystal from Sannidal, Norway, about 11/2 x 11/2 x 2 inches, bearing a few natural faces with imperfect surfaces, was prepared for etching by grinding and polishing crystal planes whose Bravais-Miller indices (referred to hexagonal axes) had been determined by X-ray methods to be 00.1, 10.0, and 10.2. Metallographic examination showed that the crystal was homogeneous, and uniform in orientation, except for the presence of twin lamellae which were oriented with their broadest surfaces parallel to the 00.1 planes of the large crystal. Since ilmenite is rather inert to standard etch reagents, strong solutions of hot sulfuric acid and cold hydrofluoric acid were used. Preliminary tests established that better etch figures were obtained using HF than with H2So4 solutions. The etch figures produced on 00.1 and 01.0 planes of ilmenite by etching 3 to 5 minutes in cold concentrated HF solution are shown in Figures 1, 2, and 3. The figures on 00.1 are "etch hillocks", rather than pits, and according to Honess(6), this phenomenon

Jan 1, 1961