Search Documents

By Wilson T. Lundy

The history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur CO. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico. Terrain Characteristic of the delta region, the terrain consists of a low, flat, uninhabited area of marsh land intersected by many shallow lakes and bayous. With the exception of salt grasses, the region is devoid of vegetation and presents, in all directions, an unobstructed path to the vagaries of the winds. The general character of this area can be best visualized from the mechanism of its formation.' Offshore bars formed enclosing long narrow lagoons between the bar and the inner shore line, the lagoons communicating with the sea by means of tidal inlets. The water in the lagoons, being comparatively quiet, favored the deposition of fine debris composed of sand carried into the lagoons by action of the waves, tides and river-borne sediments from the land surface. As this material accumulated the bottoms of the lagoons were built up and eventually salt grasses obtained a foothold. The successions of growth and decay of these grasses formed a brown fibrous mat varying in depth from a few inches to several feet. This mat of vegetation virtually floats on an ooze that is several feet thick and is composed of alluvial sediments and very fine sand, and the whole is underlain by an unctuous clay. The decayed vegetation from the upper layer when dried has a peaty appearance.

Jan 1, 1934

By Alphonse Hennin

It is well known that under certain conditions ammonia is found in the gas produced by the distillation of coal. Until recently it was held, and many still believe, that this ammonia exists in the coal, and is a natural product of the destructive distillation, varying in percentage, like the other products, according to the nature of the coal, but not formed synthetically beyond that limit. This opinion is in contradiction with well-established facts concerning the formation of ammonia from the elements of the coal. If any ammonia exists as such in the coal, the quantity is insignificant. The purpose of this paper is to explain the theory of the formation of ammonia during distillation, and call the attention of the members of the Institute to its application in connection with the production of heating-gas for metallurgical purposes, etc. For many years little or no importance was attached to the presence of ammonia in coal-gas. It was deemed by the gas-manufacturers an undesirable product of the process, as one of the impurities to be removed; and no attempt was made for its recovery. Not until its practical extraction and utilization was found possible, did scientists commence to investigate the question. Little was known about the nitrogen of the coal, and still less about the reactions leading to its transformation into ammonia. A. W. Hofmann, I believe, was the first to establish a relation between the percentage of nitrogen in the coal and the proportion of ammonia in the coal-gas. As early as 1863 he pointed out that, in dry distillation, such as is practiced in the manufacture of illuminating-gas, only one-third of the total nitrogen in the coal is liberated, two-thirds remaining in the coke. It is no longer possible to doubt that the ammonia is a synthetical product, resulting, under certain conditions, from the combination of the,elements of the coal. Chemistry teaches that ammonia is formed in many cases when

Jan 1, 1893

By P. BOURY

THIS account of a contrivance which has been found serviceable in practice may be of interest to engineers, and' especially to those engaged in hydraulic mining. In that process, one feature which seems at first sight to possess little significance, is highly important in its effects, namely, the regular supply of water to the " giants." The chief condition of this regularity is an even flow in the pipe-line from the penstock to the nozzle. This, of course, requires that the penstock be kept full. Any considerable surplus of water, overflowing at the penstock, is a simple waste, unless it be otherwise utilized in the sluices. At all events, it does not affect the delivery of the nozzles. But a deficiency at the penstock may admit air into the pipe; and this may produce hydraulic recoil, injuring the line by incessant vibrations, giving rise to leaks, and even to blow-outs, and (when a partial vacuum exists at the time of the fracture the collapse of the pipe. An accident of this sort in our main pipe-line, occasioned partly by a settling of the ground and partly by the presence of air in the pipe, led to the employment of the device here described. The line referred to is made of 30-in. pipe, successively reduced to 18 and 15 in. in diameter, for the supply of two giants. By reason of the causes above mentioned, the 30-in. pipe burst more than 1,400 ft. from the penstock, and, despite the air-valve, the 30-in. pipe was collapsed to such a degree that one length of it, next to the penstock, was squeezed together and positively swallowed by the main pipe, through which it traveled for 750 ft., piercing through a short elbow on the way. This remarkable result was undoubtedly the effect of the vacuum suddenly produced when the pipe burst.

Sep 1, 1906

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from-the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean, feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By E. Lancaster-Jones

THE gravity magnitudes obtained by means of observations with the Eötvös balance in the field are necessarily resultant or total effects due to all abnormalities of mass distribution, including even the effects due to the ellipticity and rotational motion of the whole earth. Since the object of the survey is to isolate the effects which arise solely from some particular subterranean feature, and to deduce therefrom the configuration and extent of this feature, the first step is to eliminate from the observed effects all those due to "disturbing" (i. e., unwanted) features, whether above or below the surface of the ground. The disturbing features have different characteristics, according to their situation relative to the center of the balance and to the horizontal plane through the foot of the balance, or station point; this diversity was recognized by Eötvös, who divided the total effects into so-called Normal, Terrain, Topographical, Cartographical and Subterranean effects. This classification has been adhered to by most subsequent investigators, but the writer prefers to employ the term "three-dimensional," which really indicates the essential character of the class of effect known as "Subterranean," at any rate from the standpoint of the computer of effects. Before disturbing effects can be eliminated, the features must be measured up or surveyed, whether by topographical, mining, or boring methods, and then the effects of each feature calculated and subtracted from the total observed effects. After this the problem of interpreting the residual effects will itself necessitate the computation of the assumed feature, or even a series of trial features.

Jan 1, 1928

By H. M. Otte, A. G. Crocker

SLIP, twinning, stacking faults, and precipitates on well-defined planes in a crystal produce traces that are visible on either a polished or an etched surface. The purpose of this note is to establish the usefulness and limitations of the information obtained from such traces when determining the orientation of single crystals or grains in a polycrystal. Attention will be confined specifically to traces produced by octahedral planes in cubic crystals, though most of the remarks can be taken as more generally valid. The problem of determining the crystal orientation is completely solved in principle' and in particular for the special case under consideration.1'2 Tables are available3 in which the orientations can simply be looked up when given the two or three angles between the traces. Thus a quick and simple method is available for obtaining the orientation of a crystal from surface traces. In this note two examples will be given from recently published papers and will show the use of the method with the aid of the Tables, as well as some of the precautions that should be taken in the procedure. As part of an analysis of X-ray Kossel lines, Peters and Ogilvie 4 determined from them the crystallographic orientation of the specimen. They chose a Cu-5.10 wt pct Si alloy that had been partly transformed from the a (fee) phase to the k (hcp) phase. The latter formed as very straight platelets along the octahedral planes of the a phase, and a photograph (Fig. 7 of Ref. 4) was reproduced in the paper4 of the region for which the orientation had been determined from the Kossel lines. Apart from a very small area (about 0.15 mm diam) near the top center of the photograph, the region shown was clearly all of one orientation. Traces in four different directions were readily identified. Starting with the smallest angle and proceeding counterclockwise, the angles between the traces were measured to be 27° 43', 55° 16', 64 3 43 1, and32"26'. These add up to 1802 08 1, indicating a cumulative error of 8'. The correct values should, of course, be taken from the original glass plates, or at least from prints on distortion-free paper, so the precision of the quoted values is actually greater than their accuracy. The solutions can be looked up in the Tables3 in four ways, depending on how the angles are paired, tion for the minutes of arc is required and the solution obtained will be identical for all the four pairs if the values of the angles are not in error. In a practical situation, such as this one, there are several sources of error, so that the four solutions obtained will all be slightly different. An arithmetic average of the four solutions is mathematically incorrect, but may, in special cases, give an answer close to the correct one. A rigorous procedure for refining the orientation has been described by Mackenzie;5 he gives a least-squares method that can be applied, if necessary, to this type of problem. The orientation thus determined can be compared with the one from the Kosel lines and discrepancies larger than the experimental error assigned to nonor thogonality of the X-ray or electron beam to the specimen. Here the example will only be used to illustrate the general procedure for making a very rapid rough check. From measurements on the stereographic projection, Fig. 9 of the paper,4 we can determine that the surface normal is approximately (0.434, 0.704, 0.562). From the Tables3 we find, using 28°, 55" as a good approximation to the first pair (27°43', 55°16'), that the surface normal is (0.453, 0.678, 0.579).* These two values are within 2 deg of each

Jan 1, 1967

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.' The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave's results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

By AIME AIME

The first session, held Tuesday evening, February 23, in North Sheffield Hall, was called to order by Louis V. Pirsson, Chairman of the Local Committee, who introduced Prof. Russell H. Chittenden, Dean of the Sheffield Scientific School of Yale University. Professor Chittenden, in behalf of the Governing Board, felicitated the Institute on its visit to New Haven, and cordially welcomed the members and guests to the University and the city. Dr. James Douglas, who presided at the meeting, responded in behalf of the Institute. The Secretary announced that, upon the proposal of many members, the unanimous report of the Committee on Membership, and .the unanimous recommendation of the Council, the following members had been unanimously elected by the Board of Directors Honorary Members in the American Institute of Mining Engineers Prof. Richard Beck, of Freiberg, Saxony, in recognition of his distinguished service to technical literature, and the cordial

Apr 1, 1909

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

By Ellis Clark

THE greater portion of the brown ore in the vicinity of Easton, along the north slope of the Lehigh Mountain or Durham range of hills, is obtained from mines instead of from open cuts or quarries, as is the case in the ore-beds in the western part of Northampton County, in Lehigh County, and in Berks County. The reasons for this method of procedure are various, and the principal causes of the shaft and regular mine system of working being adopted instead of the open air cuts, are : First, the large amount of stripping that would be necessary, as the richer and more valuable portions of the ore do not appear to be found as near the surface as those in other portions of the Kittatinny valley; second, the occurrence of the ore in regular beds, interstratified with the clay, and, to a less extent, in pockets or erratic deposits, as is the case in the mines of Lehigh County; and third, on account of many of the mines being situated at the immediate base of the Lehigh Mountain, where the surface water would be in such large quantities as to be with difficulty handled, and where the subsequent caving in of the sides of the open cut would be almost certain to expose the gneiss rock, which is water-bearing, the large quantities of water coming from which would probably drown out the ore-bed. Shafts, and a regular system of gangways and mining are therefore required by the configuration of the surface, the depth of the deposits and their geological structure. The ordinary size of the shafts is about four feet square, but where an extensive plant of pumping machinery is required the size may be increased to eight feet by six, with two compartments for the hoisting and pump-shaft respectively. A man-way, consisting of ladders with rests at intervals of twenty or thirty feet, is comprised in the pump-shaft, the wire rope being used for purposes of ascent and descent only in exceptional cases, on account of accidents which

Jan 1, 1879

By Thomas M. Drown

I DESIRE to communicate to the Institute the results of a few analyses which bear on the condition of carbon in gray and white iron. These analyses were made in the course of an investigation, now in progress, of the chemical composition of "chilling" irons. It will be remembered that Bell says he found no material difference in the amount and condition of carbon in gray and white pig iron made at the Clarence furnace, in England, and he therefore refers the difference in color and appearance in these two varieties of iron to the size of the particles of graphite. I quote from his "Chemical Phenomena of Iron Smelting:" "The inference I would draw from the information afforded by these analyses is, that the condition of iron in respect to its so-called `richness' is, within certain limits, entirely independent of its chemical constitution... . In the fluid state, I conceive the carbon, so taken up, confers upon the iron the property of fusion much below the temperature at which the pure metal melts, and the carbon itself may be regarded as dissolved in the iron. If, during the process of manufacture, the pig metal has been formed at a low temperature, consolidation, I imagine, takes place under such circumstances that the crystals are so minute, and the carbon which is separated assumes the uncombined or graphitic form in particles so minute as to be invisible, and, in consequence, the iron is white. If, on the other hand, the furnace is working at a very high temperature, the intensely heated iron crystallizes with large facets, upon which the extruded carbon assumes the condition of distinct plates or flakes. Should the temperature be less intense, these crystals are of smaller dimensions, and the separated carbon is less conspicuous, and, as the temperature of the furnace declines, the crystals decrease in size, as do the flakes of carbon, until both disappear in white iron. . . . Returning, then, to temperature as the cause of differences in quality of pig iron, the `chilling' of gray metal, and its conversion into white, may be regarded as the effect of preventing, by rapid cooling, the formation

Jan 1, 1875

By Edward Wichers

THE purpose of this paper is to set forth the matters of principal interest in connection with work done in the past few years on the purification of the metals of the platinum group, including the study and modification of methods already in the literature and the development of new procedures. For the most part, the results will be given in summary form, reserving the publication of detailed data and directions for a forthcoming paper to be issued by the Bureau of Standards. In recent years increasing interest has been shown in the preparation of the pure platinum metals, both by those concerned with the manufacture of the metals and their alloys for scientific and industrial purposes and those who are engaged in the study of the chemical or physical properties of the elements. The purification of the metals usually has been regarded as a matter so involved and difficult as to require the attention of specialists. It is hoped that this paper will show that any of the metals can be prepared in any desired degree of purity by relatively simple straightforward chemical methods. For the most part, it is thought that the methods given are suitable for small-scale refineries as well as for the laboratory; also, that they will bring the time required for the purification of any of the metals within reasonable limits. The new procedure suggested for purifying platinum should prove to be much shorter than any methods described in the literature.

Jan 1, 1928

By Lawrence Wright

THE occurrence of gold, gold-silver, silver-lead-zinc ores in the post-Cambrian sediments in the Black Hills of South Dakota, and their genetic relationship to the Tertiary intrusives, is well known and accepted, but the occurrence of gold in the pre-Cambrian rocks at the Homestake mine, which underlie this Tertiary gold mineralization, has given rise to differ-ences of opinion as to the period of major gold introduction into the older rocks. Fig. 1 illustrates. the distribution of mineralization along the axis of the Tertiary uplift in both pre-Cambrian and post-Cambrian rocks. The following possibilities have been presented: 1. The Homestake gold deposit was formed in pre-Cambrian time and the deposits in the overlying Cambrian sediments formed during Ter-tiary time. 2. The Homestake lode existed at the beginning of Cambrian time, but was enriched by the passage of Tertiary auriferous solutions. 3. The Homestake lode was represented by pre-Cambrian quartz-chlorite sulfide mineralization, very low in gold content and the gold superimposed on the older nearly barren mineralization during the Ter-tiary metallogenic epoch. 4. The sulfides and sulfarsenides as well as gold were deposited in both pre-Cambrian and post-Cambrian rocks during the Tertiary period. Those favoring the first proposition feel that the question is pretty well settled, while the proponents of the second theory are more flexible in their view, feeling that the amount of gold introduced in either period is still an open question. The third and fourth theories, with some modifi-cations, are supported by the proponents of the Tertiary theory, who feel that the evidence strongly favors that period. The following pages are intended to present the evidence and to give the reaction of various observers with my own comments and conclu-sions; also, the accumulated facts of observation gathered over a period of close association with the area under discussion, beginning in 1919.

Jan 1, 1936

By W. O. Brown

A laboratory investigation was conducted to determine quantitatively the extent to which connate water was contacted and displaced by invading flood water. In these experiments the connate water in unconsoli-dated sand packed columns was completely displaced by injecting water. The nature of this displacement was similar to that previously described for single-phase miscible fluid displacement studies, and thus the presence of a non-wetting immiscible phase did not appreciably change the nature of the displacement. The effects of water injection rate, column length, and oil viscosity on connate water displacement were investi-gated. It is concluded that the connate water in a reservoir is the water which actually displaces oil from the pores of the rock during a water flood. During a water flood the connate water forms a zone which separates the invading flood water from the continuous oil phase. The size and shape of connate water bank is chiefly dependent oil the oil viscosity and the column length. INTRODUCTION Water flooding is one of the most widely used techniques for the secondary recovery of oil. Presently, however, it is still not possible to recover all the oil in a reservoir by water flooding. The research described in this paper was conducted as part of a study to determine the conditions under which 100 per cent oil recovery could be attained by water flooding. The particular objective of this work was to determine if any chemical agent, regardless of its nature, placed in the flood water could be effective in influencing the mechanism of displacement of the oil by water. It has been known for many years that water does not displace all the oil in a reservoir because a portion of the oil is "trapped" and held immobile by capillary forces. This oil is trapped within the pores of a water-wet rock when it becomes broken into discontinuous globules. Initially, when oil is present at high saturations within the pores of a water-wet rock, the connate water forms rings around the points of contact of the sand grains and may even completely fill small cavities between grains, whereas the oil occupies the larger void spaces between the grains.' Under these conditions, the oil in these spaces is in the form of irregular but continuous filaments, the diameters of which depend on the geometry of the sand pores. The filaments are formed by the oil contained in the small cells which are formed between the sand grains and are connected to their neighboring cells by channels or tunnels formed by pendular rings of water. At a high oil saturation, the oil filaments conform approximately to the shape and size of the cells and their connecting tunnels. Starting with this distribution, as the water saturation is increased the water layers in the small cavities and on the surface of the grains grow. As this occurs, the water rings grow and the diameters of the oil filaments decrease. When an oil filament is reduced to a critically small diameter, the filament breaks, and its tunnel fills completely with water. Any oil which remains within a cell after all its connecting tunnels have been water-filled is trapped as a discontinuous globule. Once the oil has become trapped, the capillary forces oppose distortion of the globules and may prevent their being squeezed through the water-filled tunnels. Only a very small pressure gradient is sufficient to keep oil moving as a continuous filament. On the other hand, once the filament has broken into discontinuous oil droplets a relatively large force is required to distort the surface of a drop and move it through a water-

Jan 1, 1958

By G. E. Frantti

UNDER the auspices of the Geophysical Committee of Michigan College of Mining and Technology, an investigation was made in Michigan's Upper Peninsula to obtain geophysical data" related to the regional subsurface geology in the area covered by Paleozoic sediments. The area surveyed includes that portion of the Upper Peninsula which lies between R18W to R26W and T41N and T49N, covering approximately 1300 square miles. On the index map, Fig. 1, it is represented by the cross-hatched zone west of Munising. Four of the five sites of detailed investigation are indicated by the letters A, B, C, and D. A detailed gravity and magnetic survey had previously been conducted by J. G. Wilsonz near Perkins, 8 miles north of Rapid River, on a local anomalous area. Results of his work, which showed a large positive magnetic anomaly associated with a gravity anomaly, aroused interest in the possible economic significance of the formations underlying the Paleozoic sediments in this part of the Upper Peninsula. Early in the 1900's the Michigan Geological Survey, as well as many private companies, had done a considerable amount of dip needle work near the southwest corner of the area discussed in this paper. Most of the information available to the writer was obtained from indicated magnetic anomalies on the geological map of the northern peninsula of Michigan. Results of the geophysical activities of mining companies in the vicinity of the Marquette range and Gwinn district were unavailable to the author. Physiography and Geography: The region under consideration has low to moderate relief. About half the area is comprised of swampy lowlands, and because of the swamps and forests much of the land is almost inaccessible. The major drainage system is dendritic, with streams flowing into Lake Michigan on the south and Lake Superior on the north. The general geology, shown in Fig. 2, indicates an overlay of Paleozoic sediments on pre-Cambrian formations along a line running approximately south from Marquette (not shown on the geological map). Actual contact between pre-Cambrian and Paleozoic sediments is not known because most of the area is covered with glacial till, and outcrops are very scarce. Exposures of the Paleozoic sediments show that these beds in the northern areas dip gently under Lake Superior and that in the southern areas they 'dip gently to the southeast. Outcroppings of the pre-Cambrian formations occur primarily to the west of the surveyed area except in the northwest corner where the Laurentian series outcrop as far east as the Gwinn district and also in T46N, R24W. Instrumentation: Gravity measurements were made with the Worden portable gravity meter. Since this was chiefly a reconnaissance regional survey, both the large and small dials were used. The instrument used had a constant of 0.0035 milligals per scale division, a working range of about 25 milligals.

Jan 1, 1957

By Thomas A. Simpson

THE Birmingham red iron ore district in Jeffer-son County, north central Alabama, Fig. 1, is bounded on the northwest by the Warrior and Plateau coal fields and on the southeast by the Cahaba and Coosa coal fields. The area of study includes the ridge and valley between Red Mountain and Shades Mountain, Fig. 2, approximately 70 square miles extending from Homewood in the northeast to Greenwood in the southwest. The district is one of the most important producers of hematite in the United States, with an annual production of about 7 million tons.' The amount of hematite mined between 1870 and 1950 ranged from 6 to 16 pct of the nation's total annual production,' and the iron and steel products from blast furnaces in the Birmingham district supply the entire southeastern section of the country. Most of the mining in the Birmingham district is from slope mines along the outcrop of the ore on Red Mountain, such as Red Ore, Muscoda, Spaul- ding, and Sloss. The Pyne and the Shannon are the shaft mines of the area. The Shannon mine of Republic Steel Corp., in the central part of the area under study, is in Shades Valley at the foot of Shades Mountain. The Pyne mine of Woodward Iron Co. is 2 miles east of Readers Gap in Shades Valley. The hydrology problem has become more prevalent as mining in the area has progressed downdip. An extensive exploratory diamond drilling program is necessary to determine areas where water pressures and abnormal flows are excessive. This operation, added to higher pumpage rates, has greatly increased the costs of ore extraction. In November 1952 the U. S. Geological Survey began a detailed study of occurrence and movement of ground water in the iron mining areas of the Birmingham district. The study is a part of a small-scale but nationwide program to develop data that will be of help to the mining industry in solving mine water problems. The area of the study, in the Ridge and Valley province of the Appalachian system, Fig. 1, is a series of alternate ridges and valleys trending northeast. The principal ridges are Red Mountain, altitude about 1000 ft, and Shades Mountain, about 1100 ft. Shades Valley is between these two ridges, and its lowest point is about 480 ft. Shades Moun-

Jan 1, 1956

By Stanley L. Arnot

The Mother Lode district in California is probably better known as the land of Bret Harte and Mark Twain than as a gold-producing district, although in this respect it holds an important place. The history of quartz mining on the Mother Lode dates back to the '50s, when, after the first fever of the gold rush, men began to look for something more permanent, if not more lucrative, than the placers. Since that time, the discoveries, shutdowns, and reopenings of the many mines, together with the varying fortunes of their numerous operators, constitute an interesting chapter in California history, but one too long to include in a description of mining methods. The district is well situated, so far as physical conditions are concerned. The Mother Lode extends along the western slope of the Sierra Nevada Mountains, about half way between the crest and the Sacramento and San Joaquin Valleys, the country traversed consisting of low rolling hills—typical foot-hills. The elevation varies from 1000 to 1800 ft. and the climate is most desirable. There is an abundance of water, timber is easily obtained from the higher foot-hills a few miles east, and cheap hydro-electric power is generated practically on the Lode. These natural conditions are conducive to low costs in mining and have been the deciding factor in allowing profitable exploitation of the comparatively low-grade orebodies. Transportation facilities are not bad. Five branch railroads, from the main trunk lines in the valley, tap the district at intervals of from 10 to 30 miles, and the roads connecting these are fairly good for trucking purposes. Labor is made up of several nationalities, the principal ones being American, Spanish, Jugo-Slav, Italian, and Mexican. There were few Mexicans on the Lode prior to 1919, but the shortage of labor, experienced generally by the mining camps of the country in the years following the war, made necessary the hiring of some. The percentage of Mexican labor rapidly increased in 1920 and for a year or so thereafter, but it has now diminished until at most of the mines only a few Mexicans are working. Of the different nationalities, Americans are the most efficient and Mexicans the least.

Jan 1, 1925

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments, and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table 1 are reported the compositions of the core and cladding alloy for the material used for the experiments. [ ] In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion.1-7 Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R301 varies with the gauge, as shown in Table 2, several gauges were investigated. [ ] MATERIAL AND PROCEDURE The material used was sheet of the following gauges: 0.025, 0.040, 0.064, 0.102, 0.170. Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: 910°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After 200 min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1945

By Paul Billingsley, Augustus Locke

The mining districts of the first order' of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of compressive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 Nature of the Thrust Arc The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The. cross-sections are as shown in Fig. 2. The backbone of the belt is the upward and eastward moving block represented by the Glacier Park, the Wasatch, and the Virgin mountains, successively. The structure represented on these sections is the culmination of events which began far back in geologic time and throughout which a contrast has existed between the regions east and west of the backbone line. Before the Pennsylvanian, as Fig. 3 shows, there was a shallow shelf on the east and a deep marine trough on the west; after

Jan 1, 1935