Search Documents

By Frederic P. Dewey

By the old method of determining platinum in ores and bullion, the silver-alloy first obtained in the regular course of assay is parted in strong sulphuric acid and the residual metal weighed. This is re-alloyed with silver by a second cupellation and parted in nitric acid, the residual metal being again weighed. Any difference shown between the two weighings is assumed to be, and is called, platinum. Sometimes it is SO, and if any considerable amount of platinum be present, there will be a decided difference between the two weighings; but a slight difference is no real evidence whatever of the presence of platinum. On the other hand, the second weight may equal or possibly exceed the first, even when traces of platinum are present. Again, other members of the platinum group may go into solution in nitric acid more or less. If present, these would be called platinum and escape detection. The method does not provide any direct tests whatever as to the presence or absence of platinum. It is often indecisive, and sometimes gives erroneous results. It is, therefore, quite unsatisfactory. Being called upon many times to determine platinum in a wide variety of materials, particularly when present in very small amounts, I have realized the disadvantages and defects of this old method. In an article on the solubility of gold in nitric acid,' I have briefly outlined a method of gathering a little gold out of a solution containing much silver, which furnishes the basis of

Jan 1, 1913

By Carlos A. Aranda

The Smelting and Refining Department of Cerro de Pasco Corporation is located at La Oroya at an altitude of 3,720 meters (12,205 feet) in the Peruvian Andes. Producing lead, zinc and copper as well as twelve by-product metals and chemicals, the smelter is among the world's most complex. With the intake of high-bismuth ores in 1934, electrolytic lead refining by a modified Betts process was piloted and the plant went into commercial production in 1937 at a nominal capacity of 100 M.T. per day. After expansions in 1950 and 1963, nominal capacity has increased to 250 M.T. per day. Anodes spaced at 10.8 cm centre to centre and starting sheets are both set into the cells by overhead cranes. The asphalt-lined concrete cells are arranged in a Walker side-by-side configuration, and the electrolyte, circulating at 13 l/min./cell, is a solution of locally-produced hydrofluosilicic acid and lead fluosilicate. The corrosion cycle is limited to four days due to high impurity content of the bullion, which has successfully been treated at contents of up to 9% impurities. The cathodes are melted, drossed, and cast into blocks and pigs assaying 99.997 + % lead. The anodes with the blanket of slime adhering, are washed with electrolyte and condensate makeup water to remove the concentrated lead fluosilicate entrapped in the slimes. The slimes are then removed with high-pressure water sprays, centrifuged and sent to another plant for recovery of silver, gold, bismuth, selenium, tellurium, and antimony.

Jan 1, 1970

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

By R. O. Williams

A study utilizing neutron diffraction, electrical resistance, and chemical extraction has been carried out to clarify the chromium-rich part of the miscibility gap previously proposed for this system. This gap appears to be more symmetrical than previously supposed and is very flat. This flatness is believed to be the result of a cooperative phenomenon perhaps of magnetic origin; in particular, it is believed that the chromium-rich phase is antiferromagnetic. The presence of antiferromagnetism is believed to result in an additional strengthening mechanism very sinzilar to that for ordered precipitates. Likewise, it is proposed that the quenched alloys which are known to be ferromagnetic have antiferromagnetic regions which accounts for the maximum in hardness around 75 pct Cr. It is also believed that the existence of antiferromagnetism in other alloys of transition elements might explain some of their anomolous characteristics. THE iron-chromium phase diagram at low temper atures has recently been constructed as shown in Fig. 1(a)1 based upon that work and the work of Fisher, et al2 This system exhibits a number of extraordinary features but perhaps the most striking is the odd shape of the miscibility gap (in the

Jan 1, 1959

By J. A. Goebel, S. Rosen

IN the NiAl phase diagram the NiAl (CsC1-type) phase field extends over a large composition range. At elevated temperatures the nickel-rich phase boundary extends to a composition of about 70 at. pct Ni, a value which is within 5 at. pct of the Ni3A1 (Cu 3 Au-type) phase boundary.' At room temperature, however, the maximum nickel content is only about 60 at. pct. Experiments have shown that alloys containing greater than 63 at. pct Ni when quenched from temperatures below 1000°C contain the equilibrium phases NiAl and Ni3A1. On the other hand, when these same alloys are quenched from temperatures above 1000°C and examined microscopically, a typically martensitic decomposition product appears in the microstructure as shown in the micrograph of Fig. 1. The structure of the martensitic phase has been determined by employing powder X-ray diffraction techniques to be an "ordered" AuCu type (Strukturbericht Llo, space group P/4 mmm - DL). The diffraction pattern of this phase differs from that of AuCu in the appearance of superlattice lines. The structure is shown in Fig. 2. The open circles represent nickel atoms and the half-shaded circles represent nickel and aluminum atoms which are randomly distributed. The sites represented by half-shaded circles would be occupied solely by nickel atoms at a stoichiometry of Ni3A1. The alloys used in this investigation were prepared from 99.99 wt pct Al and 99.99 wt pct Ni by arc melting charges of varying compositions in a water-cooled copper hearth using a tungsten electrode in a gettered argon atmosphere. In all cases chemical analysis agreed within $ at. pct with the nominal compositions of the alloys. Annealing treatments were carried out in a vertical resistance furnace through which a stream of argon gas was flowing. Specimens, which were wrapped in tantalum foil, were quenched by allowing the specimens to drop into a bucket containing iced brine. X-ray diffraction patterns were obtained from -325 mesh powder specimens by using a 114.8-mm

Jan 1, 1969

By B. K. Larkin, H. K. van Poollen, H. C. Bixel

A detailed treatment is given of the transient pressure behavior of a well located near a linear discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility, and porosity are uniform, but may be different from those on the other side of the discontinuity. These results generalize previously published works which assumed the permeability ratio for media on different sides of the discontinuity was zero, one, or infinity. One application of this material would be to facilitate detection of facies changes or fluid-fluid contacts by transient testing. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables examined includes dimensionless time from 0.1 to 100, rnohility ratio from 0.001 to 1000 and specific compressibility ratio from 0.001 to 1000. For dimensionless tinze less than 0.4, the pressure behavior is essentially that of a well in an infinite reservoir. Thus, reservoir properties near the well may be estimated in the usual manner. Using an overlay technique to match an experimental curve with one of the theoretical curves, it is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time , at which a match occurs into the equation where is the diffusivity near the well, and may be estimated from data taken at early time. Because of both the complexity of the solutions and limited computer facilities, well interference problems were not examined extensively. However, it was found that well interference may be masked by the discontinuity in some cases. By superposition of the results of constant rate fluid production, the problenz of pressure buildup may be treated. Such results show that for early shut-in times correct values for the transnzissibility are obtained from conventional semilog plotting. However, erroneous values of the static reservoir pressure are obtained unless data at large shut-in times are taken. INTRODUCTION Transient well testing has yielded estimates of such reservoir parameters as static reservoir pressure, permeability. porosity, and well bore effects. In most tests, it was assumed that the reservoirs were homogeneous and iso-tropic. Anisotropic media' and radial discontinuities were considered.'.' Various studies have been made on multiple-layer reservoirs." ' Linear discontinuities have been described for problems of one-dimensional flow.' In the present paper, a mathematical treatment is given for a well located near a linear discontinuity in an otherwise infinite medium (see Fig. 1). An actual reservoir analogy would be a well in a relatively thin reservoir near a fluid-fluid contact, or a well located in a reservoir exhibiting a sudden change in rock and formation characteristics, such as thickness, porosity, or permeability. A sudden change in porosity or permeability may be caused by clay fill or other types of facies changes. Sudden thickness changes niay be the result of such geological formations as buried shore lines and channel deposits. In otherwise uniform formations, a linear discontinuity may be caused by fluid-fluid interfaces such as oil-water contacts. 3s-oil contacts, or gas-water contacts.

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By A. G. Metcalfe, Koeneman

A study of the structure of chemically deposited nickel by Goldenstein, Rostoker, Scpssberger, and Gutzeit has been reported recently. In this work it was shown that the nickel deposit produced by the catalytic nickel-reduction process was an amorphous solid. Crystallization occurred at elevated temperatures when the original powder pattern which showed only a diffuse ring with a d-spacing of 2.01A became sharp, revealing nickel and nickel-phosphide lines. The phosphide was indexed provision%lly on a tetragonal lattice of parameters a = 9.01A and c = 4.42A, which is in reasonable agreement with the structure of Ni3P proposed by No-wotny and Henglein.3 The transformation from the amorphous to the solid state occurs abruptly (e.g., after 7 min holding at 400°C) with the evolution of considerably more than 1000 cal per gm-mole. A more detailed analysis of these effects requires a knowledge of the solubility of phosphorus in nickel. Konstanti-now3 mapped out the phase diagram in 1908 but did not determine the solid solubility. The eutectic was placed at 11 pct P and 880°C. The purity of typical catalytic nickel deposits is very high.' Spectrographic analysis for heavier elements showed only trace amounts of aluminum, calcium, iron, magnesium, lead, and silicon. The term "strace" is a qualitative definition for less than 0.1 pct and probably less than 0.01 pct. Analysis for the interstitial elements yielded 0.04 pct C, 0.0023 pct 0, 0.0005 pct N, and 0.0016 pct H. Some of this material with 7.5 pct P was used in the present work. EXPERIMENTAL METHODS Alloys were prepared from carbonyl-nickel shot and a master composition containing 7.5 pct P. Cold-crucible, nonconsumable-arc melting was used.

Jan 1, 1959

By C. A. Gibbons

AFTER nine years of extremely de- pressed business, marked mostly A with red ink on the balance sheets of most coal companies and with an increasing internal competitive struggle for diminishing markets, somewhat of a change appeared during 1939. Shipments increased and prices generally firmed, giving the coal industry increasing optimism and encouragement for the future. Specifically, it now appears that bituminous coal production for 1939 will approximate 378,000,000 tons, and anthracite production will approximate 47,500,000 tons, bituminous production being around 14 per cent ahead of 1938 and anthracite production 12 per cent better. The curve on p. 31, showing both bituminous and anthracite production, furnished by the bituminous coal division of the Department of the Interior, shows graphically most of the 1939 monthly production and clearly illustrates the increased production.

Jan 1, 1940

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By P. B. Baxendell, R. Thomas

Work on the calculation of vertical two-phase flow gradients by Cia. Shell de Venezuela has been based mainly on the "energy-loss" method proposed by Poett-mann and Carpenter in 1952. The "energy-loss-factor" correlation proposed by Poettmann and Carpenter was based on relatively low-rate flow data. This correlation proved inapplicable to high-rate flow conditions. In an attempt to establish a satisfactory correlation for high rates, a series of experiments was carried out at rates up to 5,000 BID in Cia. Shell de Venezuela's La Paz field in Venezuela, using tubing strings fitted with electronic surface-recording pressure elements. As a result of these experiments a correlation between energy-loss factor and mass flow rate was established which is believed to be applicable to a wide range of conduit sizes and crude types at high flow rates (e.g., above 900 BID for 27/8-in. OD tubing). It is anticipated that the resulting gradient calculations will have an accuracy of the order of % 5 per cent. At lower flow rates the energy-loss factor cannot be considered as constant for any mass rate of flow, but varies with the free gas in place and the mixture velocity. No satisfactory correlating parameter was obtained. As a practical compromise for low flow rates, a modification of the curve proposed by Poettmann and Carpenter was used. In practice this was found to give gradient accuracies of approxirnately ± 10 per cent clown to flow rates as low as 300 B/D in 27/8-in. tubing. INTRODUCTION Production operations in Cia. Shell de Venezuela's light- and medium-crude fields are principally concerned with high-rate flowing or gas-lift wells. Under these conditions the analysis of well performance, the selection of production strings and the design of gas-lift installations are vitally dependent on an accurate knowledge of the pressure gradients involved in vertical two-phase flow. Initially, attempts were made to establish the gradients empirically as done by Gilbert,' but the results were not reliable due to scarcity of data over a full range of rates and gas-oil ratios. Several methods of calculation based on energy-balance considerations were attempted, but the computations were cumbersome and the results cliscouraging. In 1952 a paper was published by Poettmann and Carpenter' which proposed a new approach. Their method was also based on an energy-balance equation. but it was original in that no attempt was made to evaluate the various components making up the total energy losses. Instead, they proposed a form of analysis which assumed that all the significant energy losses for mutiphase flow could be correlated in a form similar to that of the Fanning equation for frictional 1osses in single-phase flow. They then derived an empirical relationship linking measurable field data with a factor which, when applied to the standard form of the Fanning equation, would enable the energy losses to be determined. The basic method was applied in Venezuela to the problem of annular flow gradients in the La Paz and Mara fields" This involved establishing a new energy-loss-factor correlation to cover high flow rates and, also, some adaptation of the method to permit mechanized calculation using punch-card machines. The final result was 1 set of gradient curves for La Paz and Mara conditions which proved to be surprisingly accurate. With the encouraging results of the annular flow calculations, several attempts were made to obtain a corresponding set of curves for tubing flow. Here, unfortunately, little progress could be made. The original correlation of Poettmann and Carpenter was based on rather 1imited data derived from low-rate observations in 23/8- and 27/8-in. OD tubing. It did not cover the higher range of production rates, and extrapolation proved unsuccessful. A new correlation covering high flow rates was required, but this proved to be extremely difficult to establish since tubing flow pressure measurements at high rates did not exist—due to the difficulty of running pressure bombs against high-velocity flow. The necessity for reliable tubing flow data increased with the development of the new concessions in Lake Maracaibo, where high-rate tubing flow from depths of 10,500 ft became routine. Thus. it was decided to set up a full-scale test to establish a reliable energy-loss factor for tubing flow conditions. A La. Paz field light-oil producer with a potential of approximately 12,000 B/D on annular flow was chosen. To obtain full pressure gradients, a special tubing string was installed which was equipped with electronic surface-recording pressure measuring devices,

By John E. Caffrey

The Federal Coal Mine Health and Safety Act of 1969, Title III, Interim Mandatory Safety Standards for Underground Coal Mines, is devoted to protection of workmen from hazards of electricity, roof, ribs, fire, and explosions. The Rules and Regulations, promulgated through the Federal Register, provide the criteria by which the law would be administered. Certain aspects of the law involve features that could be summarized under entrapment. These are sections 303 (y)(1), (y)(2) and 317 (f) (4). This paper is intended through the use of the figures to describe how these features of the law affect mine ventilation design, what are the problems, and possible solutions to them.

Jan 1, 1974

By J. H. Swartz

During 1938 and 1939, an extensive series of geophysical surveys, employing both resistivity and magnetic methods, have been carried on in the Hawaiian Islands by the Section of Geophysics of the United States Geological Survey in cooperation with the Division of Ground-Water of the Survey and the Division of Hydrography of the Territorial Government (see Fig. 1). During this time, surveys have been conducted on the islands of Oahu, Molokai, and Maui. Two distinct types of ground-water occurrence are being investigated: (1) The basal fresh-water lens floating on underlying salt water in obedience to the Ghyben-Herzberg principle (Fig. 2); and (2) perched ground-water (Fig. 3).

Jan 1, 1940

By H. S. Martin

ALTHOUGH it was known some years ago at the- Utah Copper Co. mills that fine grinding improved flotation recoveries, no accurate data were available until recently as to just how far the grinding could be carried economically. In 1923 the ultimate degree of fineness for flotation feed was supposed to be about 10 per cent. on 65 mesh, with approximately 55 per cent. through 200 mesh, which meant that most of the mineral would pass 100 mesh. At this time Garfield and Wilfley tables were used ahead of flotation and a good deal of the coarse mineral removed prior to the ball mill regrind. Shortly afterwards, mill-scale tests developed the fact that on a feed containing not over 10 per cent. +65¬mesh material flotation alone would give a copper recovery equal to that obtained by the combination of tables and flotation, but that on much coarser feed the recovery with flotation alone was lowered. This was at a time when all the sulfide minerals were floated if possible, so that the only requisite was to grind fine enough to free the mineral from gangue. EARLIEST USE op MICROSCOPIC EXAMINATION OF TAILINGS As early as 1921, the writer had attempted to determine by chemical analysis the relative proportions of copper minerals in tailings from an ore that made extremely poor flotation results. Chemical analysis was not satisfactory or conclusive, and samples of these tailings were sent to the U. S. Bureau of Mines Station at the University of Utah for micro-scopic examination. The question at that time was to determine, if possible, which copper minerals had been lost and why, but R. E. Head, in his report, revealed other interesting data. He said in part: Briefly stated, the mineral particles or grains may be classified into separate groups as follows: 1. Free grains of pyrite, chalcopyrite, chalcocite and bornite, respectively, which contain no other included sulfides; 2. Grains in which all three of the copper sulfides are represented (the core may he of chalcopyrite, partially altered to bornite, these two minerals being entirely surrounded by a shell of chalcocite); 3. Grains composed of equal amounts of bornite and chalcocite or chalcopyrite and chalcocite.

Jan 1, 1929

By O. M. McRae

The Courtland-Gleeson area is in Cochise County about 15 miles east of Tombstone in southeastern Arizona. Rocks exposed in the area range in age from Pre-cambrian to Quaternary. The Precambrian is repre-sented by the Pinal schist. Paleozoic rocks include the Cambrian Bolsa quartzite and Abrigo limestone, Mississippian Escabrosa limestone, and the Permo-Carboniferous Naco Group limestones. Rocks believed to be of Triassic and/or Jurassic age include the Copper Belle monzonite porphyry, Turquoise granite, and Gleeson quartz monzonite. The Cretaceous is represented by andesitic volcanics and various sedimentary rocks. Tertiary rocks include the intrusive and extrusive Sugarloaf quartz latite porphyry and numerous dikes of various rock types. Quaternary conglomerates cover the northern and eastern part of the area. The geologic structure is extremely complex. All rocks as old as early Tertiary have been involved in either tilting, normal faulting, high angle reverse faulting, imbricate thrusting or folding and overfold-ing. Major deformation was initiated during the first half of the Tertiary. Northeast-southwest compres-sional forces caused thrust plates containing lower Paleozoic rocks to override Cretaceous rocks. Subsequently, two large slide blocks of lower Paleozoic rocks, acting under the influence of gravity, moved eastward. The imbricate structure and the gravity slide blocks were then broken by late Tertiary normal faults. INTRODUCTION The Courtland-Gleeson area, or Turquoise Mining District, has long been recognized as an area of extreme structural complexity. Gilluly 2 referred to the entire district as a "gigantic thrust breccia". In 1962, Bear Creek Mining Company completed a two year program of detailed geologic mapping supported by exploration drilling. The purpose of this paper is to present some of the results of this investigation and to provide a structural interpretation based on these results. The geologic map that accompanies this report is generalized and shows only the major and significant features. The area was initially mapped on aerial photographs on a scale of 1 in. equals approximately 500 ft. These data were transferred to a planimetric base using a vertical sketch master. LOCATION The Courtland-Gleeson area is in central Cochise County, about fifteen miles east of Tombstone, and about twenty-two miles northeast of Bisbee in southeastern Arizona (Fig. 1). The area is readily accessible over graded gravel roads from both Tombstone and Elfrida. GENERAL GEOLOGY Rocks exposed in the area range in age from Pre-cambrian to Quaternary. wilson3 and Gilluly2 have published very detailed descriptions of the principal rock units exposed in the area. Only a summary description is provided in Table I. A great number of previously unmapped narrow Tertiary dikes and small irregular masses of hornblende andesite porphyry, lamprophyre, and aplite intrude the Gleeson quartz monzonite in the western part of the map area. The scale of the map prohibits showing them. The aplite dikes are related to, and bear the same structural relationships as, the Sugarloaf quartz latite dikes found in this area. For that reason, and because both the hornblende andesite porphyry and the lamprophyre are post-mineral and post-thrusting, their omission from the map is not considered significant. Because so many of the contacts in the district are fault contacts, because bedding faults appear to be prevalent but are difficult to recognize and map, and because igneous intrusions are so common throughout the sedimentary section, it is virtually impossible to measure an exact total thickness of any of the sedimentary rock units. Nevertheless, neither the field mapping program nor the diamond drilling provided any basis for suspecting that the thicknesses of the sedimentary units are significantly greater or less than what might be inferred from surrounding districts.

Jan 1, 1967

By J. B. Gwiazda

This work contains a description of a new design of lemniscate-guided powered roof support units, with a discussion of currently designed supports and their interaction with the roof. Conventional roof supports of this type present a serious reaction with the roof because of the horizontal displacement of the canopy in the course of decreasing support height as the support takes weight. The new design presented eliminates previous disadvantages of lemniscate supports and ensures proper performance of the latter in relation to the roof of a mine working.

Jan 1, 1986

By E. R. Williams

Continuous casting of nonferrous metals has become a commercial reality. After years of slow and arduous experimentation by a number of independently working inventors, starting with Lord Henry Bessemer in 1865, success has finally been achieved. Nonferrous metals—aluminum, copper and brass—extremely vital to our production of war equipment, are being continuously cast every day in large quantities. In fact, some nonferrous metals —for instance, high-strength aluminum alloys—could not have been produced in the huge quantities required for planes and other war equipment if it were not for continuous casting. These casting processes for nonferrous metals have not been entirely perfected but continuous casting is here to stay. Continuous casting of carbon and alloy steel has not yet gone into commercial production but it is well on its way. A great deal of hard work has been expended and -small fortunes in money have been and are being spent in marching down the long road to success. Considerable tonnage of plain carbon, stainless and other alloy steels of high quality have been produced by pilot-plant continuous-casting units and at speeds that give indisputable evidence of commercial success. What has made the difference between failure and success? What is there left to do to revolutionize completely the method of casting metals, which has existed for centuries? These questions are being rapidly answered. Fundamental Methods Present continuous casting processes have many common problems but differ considerably in their methods of solution. The two fundamental methods are: I. Forming the solidifying metal against mold walls that move with the metal, so that there is no relative movement between the walls and the metal. This is a development of Lord Bessemer's idea of pouring metal between two rotating rolls. 2. Moving the solidifying metal along a stationary mold wall so that there is relative movement between the wall and the metal. This was proposed by Trotz in Germany as far back as 1889. Neither Bessemer nor Trotz achieved commercial success. The chief reason seems quite apparent today, inasmuch as they did not solve the fundamental problem of rapid heat removal from the molten metal. The Williams Continuous Casting Process is based upon this fundamental idea of fast heat removal and dissipation. The bessemer method of forming the ingot against a moving mold wall—either rotating rolls or endless moving plates—was carefully considered by the author and promptly abandoned as being commercially impractical. Primarily, only a very small tonnage output was possible except at terrific lineal speeds, because the very nature of this method required casting thin sheets rather than ingots. Secondly, the casting of a sheet between lolls that are pressed together meant the rolling of two layers of solidified skin separated by a molten core. Internal bursts and segregation of the metal usually resulted. Moving Solidifying Ingot Along Mold Wall It was decided therefore to devote our research activities chiefly to- the idea of moving the solidifying ingot along. a stationary mold wall. It was soon dis-

Jan 1, 1945

The October issues* of the Journals of the three AIME Societies carried a brief resume of the historical development of various technical and professional organizations which in some immediate or remote way affect the individual member of AIME. This resume was presented by the Institute Committee on Inter-Engineering Society Cooperation. Recently, several plans have evolved designed as a first step to provide a so-called "unity organization" for the entire engineering profession. Almost all of the plans involve Engineers' Joint Council, Engineers' Council for Professional Development, and National Society for Professional Engineers in some way or other. Hence our committee is presenting to our membership a resume of the recent activities of the two umbrella organizations and of NSPE. More detailed information on any of these organizations may be obtained from annual reports published by the organizations.

Jan 2, 1961

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942

By Francis M. Walters, Irwin R. Kramer

The substitution of cobalt for part of the nickel in Invar was found by P. H. Brace1 to lower the coefficient 01 expansion. Scott1 extended the use of cobalt to alloys of higher inflection temperatures. Such alloys have a larger temperature range of low expansion than those without cobalt, and their use up to 400' or 500°C. offers decided advantages in certain applications. However, it has been found that the iron-nickel-cobalt alloys are not stable in this temperature range. Experimental Methods Two methods were used in studying the stability of the low-expansion iron -nickel-cobalt alloys. Dilatometer specimens were held at 480°C. for 9 months and the change in expansion characteristics was dctcr- mined. Filings were held for about 2 months at various temperatures and the change in structure was determined by X-ray diffraction. As shown by Table I, the alloys studied covered a wide range in nickel plus cobalt content (which determines the inflection temperature) as well as some variation in the ratio of nickel to iron (which controls the temperature of the gamma to alpha transformation). Included also are alloys containing carbon and vanadium, carbon and titanium and three with various amounts of copper. The alloys were melted in a high-frequency induction furnace with a magnesia crucible, using ingot iron, electrolytic nickel and commercial cobalt. Fifteen-pound heats were cast into iron molds after deoxidizing with silicon, or

Jan 1, 1942