Search Documents

By S. Weinig, E. S. Machlin

THE mechanism of the martensitic transformation has been the subject of a remarkable number of papers in recent years.' Because the task of evaluating all the available theories is a formidable one, the authors will confine themselves merely to the presentation of results of an experimental investigation of the habit orientation, lattice relations, magnitude and direction of average transformation shear strain, and orientation of subband markings for a single variant of the possible habit systems in an 11 pct Mo-Ti alloy. It is hoped that these data will assist in the establishment of a rigorous theory for the mechanism of the martensitic transformation. Experimental Procedure Specimen Preparation: A sample, approximately 1/2 x 1/4 x 1/4 in., was cut from a double arc-melted ingot composed of commercial-process A titanium and high purity molybdenum (nominally, 11 pct Mo). It was capsuled in evacuated Vycor at 10.-3 mm Hg subsequent to a double argon wash and homogenized for 48 hr at 1100°C. After a direct quench into H2O at room temperature, a large-grained specimen resulted, which, by X-ray diffraction and metallographic means, was subsequently shown to be in the body-centered-cubic phase, ß. Two adjacent, approximately perpendicular faces were polished and the ends of the specimen were ground parallel in a V-block. Fiducial lines were inscribed at 45" to the common edge of the polished surfaces in order that they would be perpendicular to the habit traces of the subsequently formed a plates.2 The specimen was then compressed between the ground ends in a Buehler press to stress induce the transformation ß to a'. Experimental Measurements: The habit-plane orientation, the orientation of subband markings, the orientation relation between the parent ß and the product a', and the transformation strain for the same plate were determined. To further establish the nature of the subbands, one surface was repol-ished and etched. The bands in the a' were still visible and were found to be optically anisotropic under polarized light. Back-reflection Laue patterns were obtained from the ß matrix and from a region comprising both a' plates and adjacent ß matrix (a Cu target was used). By superposition of the two X-ray diffraction patterns, it was possible to obtain a tentative orientation relationship between the two phases. This result was confirmed by a pattern taken after the specimen was rotated to make the basal-plane pole of the hexagonal a' phase strike the film. This necessitated cutting the specimen to expose the a' plate in the new position relative to the X-ray beam. Analysis of Experimental Measurements On the basis of the aforementioned X-ray patterns, the orientation between parent and product

Jan 1, 1955

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By J. H. Hollomon, L. D. Jaffe

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By L. D. Jaffe, J. H. Hollomon

The hardenability concept has become widely used during the last few years for the choice and substitution of steels. Before the work of Grossmann,1 the systems for predicting hardenability from chemical composition could be used only over a narrow range of composition. Grossmann introduced a comprehensive system, which has been effective in calculating the hardenability of most types of moderate or low-alloy steels. However, occasions often arise that require the calculation of the hardenability of high-alloy steels from their chemical compositions. Experimental determinations of the hardenabilities of such steels indicate that the Grossmann system predicts much greater hardenabilities than are realized. The fact that cases do arise in which the Grossmann method does not apply indicates that the fundamental hypothesis of the system may not be generally applicable. It seems advisable to re-examine not only Grossmann's system but also the concept of hardenability itself. Hardenability If steel parts are to possess a martensitic structure after quenching, they must first be austenitized and then cooled through the pearlite and bainite transformation ranges sufficiently rapidly to avoid the formation of pearlite, bainite, and pro-eutectoid products.* If, on cooling, these transformations are avoided, the resulting structure can consist only of martensite (and retained austenite). The hardenability of a steel is measured in terms of the severity of the cooling conditions necessary to avoid the pearlite and bainite transformations. The less rapid is the cooling necessary to prevent the formation of bainite and pearlite, the higher is the hardenability. The pearlite and bainite reactions appear to be differently affected by the alloying elements. Not only is this indicated by the published isothermal transformation data, but recent work by Zener2 affords a rational interpretation of the differing effects of the alloying elements. Manganese,3 for example, appears to decrease the rates of the pearlite and bainite transformations by equal percentages, while molybdenum45 is approximately 10,000 times more effective in retarding the pearlite than in retarding the bainite transformation, on the basis of isothermal measurements. In some steels, the formation of bainite restricts the formation of martensite while

Jan 1, 1947

By E. F. La Vigne

On Aug. 10, 1884, the Retsof Mining Co. began the sinking of an 18 by 12-ft. shaft at Retsof, N. Y. Rock salt was reached in 1885, in September, at 1008 ft. below the surface. The first salt was shipped in the fall of 1885. A timber breaker was built in 1886. In July, 1895, there was a consolidation of the Retsof Mining Co., the Greigsville Salt & Mining Co., the Livonia Salt Co., and the Lehigh Salt & Mining Co. These consolidated salt companies are now known as the Retsof Mining Co., a subsidiary of the International Salt Go. Eventually all of the mines were closed except the mine of the Retsof Mining Co., at Retsof, Livingston County, New York. On July 6, 1921, about 1/2 mile south of the original shaft arid plant of the Retsof Mining Co., a new 9 by 28-ft. concrete-liried shaft was started. The shaft is 1063 ft. deep from the top of the shaft collar to the bottom of the salt bed. At the same time a reinforced-concrete breaker and other buildings were erccted. This new plant began operations on Dee. 15, 1923. It was designed for a capacity of 3000 tons in 8 hours. Geology The workable rock-salt bed is 1063 ft. below the surface and 326 ft. below sea level, and varies in thickness from 9 to 10 ft. The total thickness is greater than that but is contaminated with shale above and below the pure mineral. The characteristics of the formation are shown in Tables 1 and 2. The bed dips uniformly 0.87 per cent to the south. Prospecting As the salt deposil in New York State is known, very little prospecting has been necessary. Before the sinking of the Retsof No. 1 shaft, a well was drilled to prove the existence of salt. No. 1 shaft was sunk where the well was located. The several salt wells drilled in Livingston Courlty proved generally the existence of salt throughout the county. (See U. S. Geol. Survey Bull. 669: Salt Resources of the U. S.)

Jan 1, 1938

By Earle C. Smith

The Chairman.—Mr. Earle Smith has kindly offered to make some remarks in connection with segregation in the product, Mr. Smith: E. C. Smith,* Cleveland, Ohio—I will start this Off by a story oF the code days of the American Iron and Steel Institute. In those days, Republic did not have a big strip mill, and the question came up of the check analysis of rimmed steel. I suggested that they let me be the chairman of the Committee on Accumulating the Information on the Variation of the Composition of the Ingots of Rimmed Steel. Somebody wanted to know why I wanted to be the chairman. I said, "we don't make any of the big ingots of rimmed steel, and no matter who makes them they are so bad that you don't dare publish the information. So if 1 collect it and hide it you can't charge me with having done anything that really disrupted the commercial situation." So, everybody furnished me with a rather complete story as to the horrible variations in big rimmed ingots. I took it out to my house and put it away, and it is still there. Now, segregation in the big ingot is no longer an "academic " matter as far as I am concerned. I am in a situation like that of the German who was told in 1956 about the coming war. He said: "until it is your throat that is going to be cut, you don't pay any attention to what is happening to the otherman." 'That is the way with the problem that we have in front of us. Recently I have been told that the 'Omptroller was questioning the payment for certain articles of stamped steel that had been made from rimmed steel, because upon check analysis of the rimmed steel it had been determined that these stamped articles were nut within the compositions that were included in the specification, and therefore he as the camptroller had no alternative. It was not meeting the specification; therefore, no payment. So I I say to all of you: You can very seriously consider this matter of segregation now and on into the future on the basis of the fact that it is actually going to cost your companies, which are making these products, money unless there is some new idea about the infallibility of quantitative , chemists who analyze some of these products or lawyers who read specifications, I don't know which man is going to be the major factor in the future. if the National Bureau of Standards could in some way show the specification writers the variation between good chemists analyzing for That they expect to be umpire eel. the writers would certainly realize that some of the to to which we have calmly signed our names as being O.K. are— well, as one man said to me, they might be filled by the devil, and they certainly could be filled by the Lord, but they could not he me by mankind. I would like to inject two or three things into a segregation study which I Want you to think about, because 1 would be a little surprised if there is very much discussion of them, In the first place, we generslly make steel in the United States in the basic open hearth, and I do not think there has bee,, nearly enough consideration given to segregation German the bath before it moves into the ladle. I am sure that any of the people who handled the 9400 series of the NE series when it contained the 0,60 per cent silicon have more respect than they had previously for the segregation that is within, the ladle; that is, before the metal reaches the ingot mold, the frozen ingots and the segregation in them. Another pint to which I think We ought to sis serious consideration is the segregation of iron oxide in the ingot-iron type of material, where the distinction between that and the steel segregation is that it is actually segregat. ing iron oxide, Normally we are segregating some form of carbon or sulphur, or something like that, with the stamping steel industry now coming down into the ranges of chemistry, where the segregation of iron oxide will be just

Jan 1, 1945

By J. A. Herrick Nashua

IN this country steel made in a Siemens furnace or Bessemer converter, is generally tapped into a ladle or shoe, and then drawn through an aperture in its base into the various moulds. In order to regulate the flow of the molten mass a refractory valve is arranged at the aperture. A plumbago nozzle is fixed firmly in this aperture, and a stopper of like material is fitted to it, making a socket valve. In order to raise and depress this stopper at will, a rod is fastened-to it, extending through, the metal and over the brim of the ladle, where it is bent back in a half circle and secured in a slide. This slide plays vertically in a frame, permanently fastened to the outside of the ladle, and is moved by a lever having as a fulcrum a pin fixed in this frame, one end, of the lever being temporarily fixed to the slide, and the other end being moved by hand. Reference being had to the drawing (see Plate 1, Fig. 1), E is the nozzle, D is the stopper, A is the rod, protected as hereinafter described, C is the cast-iron framework, B is the wrought-iron slide, B' is the offset into which the rod, A, enters, and is secured in the usual manner by a key, a. Section J, K, shows the manner of hanging the lever. J is a pin attached to the slide by which the end of the lever raises the slide, B. J is the fulcrum fastened to the frame, C. K (Fig. 1) is a hand-nut fastening the slide, B, to the frame, C, at will. Fig. 2 is a side elevation of ladle, showing the outside working of the parts above described. It is the common practice to protect the rod, A, by a coating of clay and fire-sand, kneaded to the right consistency and applied to the rod, and then thoroughly dried. Just before casting, the plumbago stopper, D, is heated at its extremity to redness separate from the ladle and, at the moment of pouring, is placed in the ladle and slide, and adjusted as well as practicable. Some very serious defects ensue, causing much trouble and vexation as well as actual loss. The fire-clay coating in drying becomes cracked and seamy, and at its best is more or less loose on the rod. The hot metal sometimes cuts

Jan 1, 1879

By C. W. Sherman, N. J. Grant

The correlation of the high temperature chemical properties of slag-metal systems with some easily measured property of either slag or metal at room temperature has been the goal of both process metallurgists and melting operators for many years. There are several rapid methods for estimating various constituents in steel in addition to the conventional chemical methods which are quite fast, but these do not reveal the nature of the slag as a refining agent, which is of primary interest to the steelmaker. Furthermore, there are several methods for examining slag, the three principal ones being slag pancake, petrographic examination, and the previously mentioned chemical analysis. The main objection to the last two is the lime required to make a satisfactory estimate of the mineralogical or chemical components. The objection to the first is the inadequacy of the information obtained. A new technique has been developed by Philbrook, Jolly and Henry1 whereby the properties of slags are evaluated from an aqueous solution leached from a finely divided sample of slag. It is known that the pH or hydrogen ion concentration (of saturated solutions that have dissolved certain basic oxides, notably calcium oxide) will indicate a pronounced basicity. Philbrook, Jolly and Henry devised the pH measurement technique in order to supply open hearth operators with a fast, reasonably accurate method of estimating slag basicity. They offered the method as an empirical observation and made no claims as to its theoretical justification. The results were presented as an experi-metally observed relationship which applied over an important range of basic open hearth slags. They found that, in plotting the measured pH against the basicity, the best relationship existed between the pH and the log of the simple V ratio, CaO/SiO2. Extensive investigation also showed that there were several variables in the experimental technique that influenced the results and necessitated following a standard procedure to obtain reproducible pH readings. These variables were: 1. Particle size of the slag powder used. 2. Weight of sample used per given volume of water. 3. Time of shaking and standing allowed before the pH was measured. 4. Exclusion of free access of atmospheric carbon dioxide to the suspension. 5. Temperature of the extract at the time the pH was measured. In subsequent investigations of the pH method by Tenenbaum and Brown2 and by Smith, Monaghan and Hay3 the general conclusions of Philbrook's work were reaffirmed. It was the object of the present investigation to extend the technique to a point where it could be used to evaluate slags of all types. Experimental Results PARTICLE SIZK OF SLAG POWDER A large sample of commercial blast furnace slag of intermediate basicity (V-ratio 1.15) was selected for the study. The slag had been put through a jaw crusher until all of it passed through a 20 mesh screen. Five fractions of this crushed material were separated, -20 to +40, -40 to +60, -60 to +100, -100 to +200, and -200 mesh. A representative sample of 0.5 g was removed from each fraction and the pH determined using the method of Philbrook. Check pH analyses on the sample fractions varied due to the different amounts of shaking. To eliminate this variable, a mechanical shaker was employed. In order to know the exact time of contact between the slag and water, it was found necessary to filter the extract at the end of the shaking period. Using the mechanical shaker and a filtering apparatus, similar runs were made on the five fractions for contact times of 5, 10, 20, and 40 min. Random checks gave reproducible results within 0.02 pH. The data are plotted in Fig 1. It can be seen from the plot that each slag fraction is hydrolyzed to an extent that is roughly proportional to the surface area exposed to the water. The (—100 to +200) mesh material changed very little in pH after 10 min. shaking time. The curves are symmetrical and lie in proper relation to one another. The —200 mesh curve appears to be somewhat flatter than the others, but this can be attributed to the portion of very fine material that is not present in the other fractions. The closeness of the (-100 to +200) mesh curve to the —200 mesh curve and the fact that a —100 mesh sample would contain amounts of slag down to 1 or 2 microns in diam were considered sufficient reasons for selecting a —100 mesh sample as representative of the whole sample of slag for the purposes of this investigation.

Jan 1, 1950

By R. Wiesenthal

A method is developed for improving the low recovery efficiency which results when viscous oils are flooded by water. Viscous oil has been diluted with a lighter liquid miscible in it in any ratio which produces a mixture possessing a reduced viscosity and which is then displaced by water. Light gasoline was used in these tests to reduce the viscosity of the oil in place. Oils possessing viscosities in the range of 1.28 to 324 cp at the test temperature of 30C were displaced from a cylindrical unconsolidated sand core, with a length of 2 m (6.6 ft) and a diameter of 10 cm (3.9 in.) at a flood of 6.27 cc/sq cm/hr. In two test series up to I PV of light gasoline was injected into the core before water flooding. In the first series the recovery of a low-viscosity oil (1.28 cp) increased as the volume of light gasoline was increased. However, only the oil which could not be recovered by water flooding alone could be replaced by the light gasoline. In the other series, the recovery of a more viscous oil (13.5 cp) was not increased even if large quantities of light gasoline were injected. An oil bank built up ahead of the water front so that the flood water met with equivalent saturation conditions, as would be the case in flooding solely with water. However, the recovery of more viscous oils could be increased substantially when the core was first flooded with water, followed by a slug of light gasoline, and then flooded with water again. Furthermore, an oil bank ,built up ahead of the second water front. The formation of this oil bank is particularly favorable for the displacement process; the greater part of the light gasoline injected was pushed out of the core ahead of the oil and recovered. Using a light oil of low viscosity, it was possible to replace only the residual oil that could not be recovered by water flooding by the light gasoline. As the basic study had shown that highly viscous oils could be recovered by flooding first with water, then with light gasoline, followed by a second injection of water, the study was extended by tests made with reservoir fluids and cores taken from the low-gravity oil reservoir of the Wietze field, Germany. A great increase in recovery over flooding with water alone was obtained in these tests. The results may show a way to recover high-viscosity oils by a comparatively simple flooding procedure. INTRODUCTION In fields where oil recovery has not benefited from natural water drive, increased recovery may be obtained by the injection of water into the reservoir, especially in the case of fields which produce high-gravity, low-viscosity oil. There is a rather close relation between the viscosity of the reservoir fluid and the recovery that can be obtained by water flooding. As the viscosity increases the oil recovery decreases proportionately, so that an oil viscosity about 30 times that of water is generally considered to be the upper limit for an economically successful water flood.' This limitation has been recognized theoretically by Buckley and Leverett,' and has been verified by numerous laboratory flooding tests, such as by Croes and Schwarz,V n the viscosity ratio range of oil to water from 1 to 500. The reason for the inferior recovery of viscous oils by water flooding can best be understood by considering the mechanism of flood tests. In such tests water is introduced into one end of a sand-packed tube which is saturated with oil of the viscosity to be tested, and oil is produced from, the other end. Oil, with a viscosity lower than that of water, is pushed ahead of the advancing water with considerable uniformity, and irregularities in the displacement process tend to be eliminated as the oil saturation decreases and the water saturation increases. However, oil recovery is not complete, for the water forms interfaces with the oil and traps residual oil droplets in certain of the pore spaces. These residual oil droplets are distributed rather uniformly through the sand, and they are not susceptible to recovery regardless of the amount of water passed through the test cylinder. In the case of an oil possessing a viscosity greater than that of water, the injected water tends to move irregularly through the sand in the test cylinder. At the place in the sand where initial water movement takes place, resistance to the movement of water is lowered and the water finger so formed will grow perceptibly; it will extend to the outlet end of the test cylinder so that a breakthrough of water takes place long before much of the oil-saturated volume of the sand has come in contact with water. Once the breakthrough of water takes place, the water-oil ratio is gradually approaching the economic limit, even though much of the oil in the test cylinder remains unaffected by water. Disconnected drops of oil are trapped in the portion of the sand that has been invaded by water, just as when an oil of low viscosity is flooded. The poor recovery of the more viscous oils, therefore, is due to the irregularity of water movement through the test cylinder, and the rate of water movement through restricted sections of the oil-saturated sand increases with the more viscous oils. There are three ways whereby the recovery of viscous oils by water flooding can be improved:' (1) adding materials which will increase the vis-

Jan 1, 1965

By C. A. Siebert, O. S. Duffendack, A. W. Herbenar

IN metallurgical problems involving the study of equilibrium in binary systems, the ,existence of an additional vapor phase, due to the presence of a volatile component in the alloy, has often been neglected. This is well indicated by the modified form of the phase rule, usually accepted in condensed systems in which pressure is not considered as a degree of freedom. In many cases the vapor pressure of the volatile component is exceedingly small and for all purposes can be considered negligible, in which case this form of the phase rule is applicable. However, alloys containing Hg, Cd, Zn, or Mg, tend to show very marked equilibrium vapor pressure, even in the solid state, and therefore present cases where the modified form of the phase rule no longer holds true. A quantitative determination of the vapor pressure of zinc in alpha brasses is not only of practical interest because of the loss of zinc in the processing of these alloys, but also of theoretical interest in that such measurements provide a means of applying the principles of theoretical physics and physical chemistry to problems of applied metallurgy. A number of investigators have reported vapor pressure measurements of zinc in alpha brasses. Hargreaves1 made extensive measurements which were used by Birchenall and Mehl² and Guttman³ for the determination of activity coefficients of zinc in alpha brasses. Hargreaves1 used a differentially heated quartz tube and measured the condensation temperature at one end corresponding to the temperature of the heated brass at the other end. Birchenall and Cheng outlined the condensation method of obtaining vapor pressure of zinc and Cd over some of their silver alloys." The primary object of the present investigation was to increase the range and accuracy of the vapor pressure data for the alpha brasses. Preparation of Alloys: Six alloys were prepared from Bunkerhill zinc and O.F.H.C. copper, both of 99.99 pct purity. The cast ingots were annealed for 24 hr at 550°C, scalped, cold rolled 40 pct and annealed for 50 hr at 550°C. The annealed bars were then surface ground and degasified for 30 min at approximately 550°C in an induction heated vacuum furnace. The surface of the bars was removed before milling the bars into relatively fine chips for chemical analysis and samples for the equilibrium cell. The analyses of the six alloys are given in table I. Experimental Method: The vapor pressure of zinc over the various alloys at a number of temperatures was determined from absorption spectra data. The spark source was produced by means of a high tension discharge between two electrodes of pure zinc. The design of the absorption vessel is shown in fig. 1. The vessel was constructed of transparent quartz which transmits the whole of the visible spectrum and the ultraviolet down to a wave length of 2000 A. The thickness of the vapor space was set at 0.8 mm so as to permit a relatively wide range of measurements without altering the vapor space, and thereby necessitating recalibration of the vessel. The furnace used for heating the absorption vessel consisted of a split wound furnace as shown in fig. 2. The spectrograph used in obtaining the transmitted zinc spectra was a double prism type especially designed for a region of 2500-3500 A. A step diaphragm used in conjunction with a tungsten filament provided the necessary intensity patterns required for calibration of the photographic plates.

Jan 1, 1951

By A. R. Kinkel

THE Shasta copper-zinc district of northern California lies in the foothills of the Klamath Mountains at the northern end of the Sacramento Valley. It contains two main areas of base-metal ore deposits, the East Shasta and West Shasta districts shown in Fig. 1. The East Shasta includes the area from the Afterthought mine, near the settlement of Ingot on U. S. highway 299 East, to the Bully Hill mine, on the north side of the Pit River, 9 miles to the northwest. The West Shasta, a well-defined northeast-trending district about 8 miles long and 2 miles wide, west of the Sacramento River, Fig. 2, is the western part of the ore-bearing area formerly known as the Shasta copper belt. Referred to in the older writings as a copper arc, this belt was thought to form a crescent extending entirely around the head of the Sacramento Valley, the convex side to the north. Recent studies by the U. S. Geological Survey in cooperation with the California State Division of Mines show that there are two districts, one at each end of the so-called copper arc, which are distinct in geologic structure and ore occurrences, and that there is only sporadic and unconnected copper mineralization between them. Ore deposits of the two districts are similar in mineralogy, that is, they are largely massive pyritic ores containing copper and zinc with minor amounts of gold and silver, but the structure and structural control of ore deposition are different. The ores of the East Shasta district are replacements of steeply dipping shear zones in Triassic rhyolite and shale, whereas those of the West Shasta district are replacements of gently dipping rhyolite of Middle Devonian age and are essentially flat-lying. Thus there is marked lateral control of orebodies by shear zones in the East Shasta district and equally marked vertical control of orebodies by the stratigraphy in the West Shasta district. Geologic Setting The Paleozoic rocks of the West Shasta district range in age from Middle Devonian (?) to Missis-sippian. The oldest formation exposed is the Copley greenstone, probably Middle Devonian. It is composed of volcanic flows, volcanic breccias, and tuffs, all of mafic composition, but contains minor amounts of shale and rhyolitic tuff. Largely submarine in origin, it rests upon a base of older marine sediments, as shown diagrammatically in Fig. 3. The lower part of the formation is made up principally of flows, many of which are ellipsoidal, and the upper part contains most of the pyroclastic material. The formation is at least 3700 ft thick. The Balaklala rhyolite overlying the Copley greenstone is made up of many rhyolitic flows and beds

Jan 1, 1956

By Victor J. Miller

The Northeast Tripp Slide is one of the larger slope failures that can be attributed to open pit mining. It is a 11.7 million cubic meter (15.3 x l0 6 yd3) wedge failure created by two thick gouge-filled fault zones whose intersection plunges into the Tripp pit at 13°. One unique aspect of this failure is that the slide is now stable despite having moved an estimated 8.5m (28 ft.) towards the pit and having reached a maximum overall velocity of 2lmmlday (0.07 ft/day). The slide started to fail in 1968, accelerated until mining in the slide's toe area was halted in April 1970, then began to decelerate. With the cessation of mining in the toe area, rubblized rock sloughed into the pit bottom which added weight to the failures toe constraints and began the stabilization process. Measurements from a network of survey stations revealed a correlation between the slide's velocity and heavy precipitation. Runoff water accumulating in the tension cracks is believed responsible for this correlation. Moreover, the survey net measurements showed that during the failure's last stage the vertical component of the slide's movement greatly increased. It is proposed that this settling was caused by plastic-like flowage of the clay gouge underlying the failure The fault zone's effective shear strength was estimated by a back- analysis on the wedge's geometry and by performing direct shear tests. The tests, performed on cores taken from samples that were collected on the failure, yielded a residual shear strength of: cohesion 0.61 kg/cm2 (8.7 lb/in2), and a friction angle of 9.6°. This residual shear strength was near1y equal to the back-calculated strength indicating that the controlling fault's effective strength was essentially the same as the residual shear strength of the gouge filling

Jan 1, 1983

By G. Ostberg

OXYGEN has frequently been considered responsible for phenomena in the metallurgy of cast iron which are not sufficiently explained by the presence of other elements. Oxygen and oxides have been regarded as critical factors, particularly for the solidification process, and specifically in the formation of graphite. However, the evidence for an influence of oxygen has mostly only been indirect or qualitative. Furthermore, quantitative data on the oxygen content of cast iron presented in the literature have often been less conclusive as being apparently determined with insufficient regard for the difficulties associated with the sampling and analysis. These problems, experimental and theoretical, have been studied in this investigation. An attempt is made to bring the views on the soluble amount of oxygen in cast iron on a level with the present understanding of the thermodynamics of these types of alloys. Although there are no experimental data on the complete multicomponent cast-iron alloys some conclusions have been drawn from investigations on simpler systems. The order of magnitude of the solubility of oxygen in cast iron is considered in the first part of the paper. The second part deals with the oxygen content actually present under practical conditions. First the possible sources of errors in sampling and analyzing methods are examined. Finally some observations on the oxygen and oxide content of malleable iron during the production process are made. THERMODYNAMICS OF OXYGEN SOLUBILITY When cast iron is saturated with oxygen the saturation phase is essentially carbon monoxide or silicon dioxide depending upon the composition of the iron, the temperature, and the rates of formation of the oxides.* The latter occurs accordiw to the O + C = CO, Kc0 - a COa J 20 + Si = SiO2, Activities are used here instead of weight pct concentrations, since activities are believed to show more sensitively the effects of the interaction of all the alloying elements. Calculations involving activities are, however, seriously hampered by lack of experimental data on the interactions between the components encountered in the multi component cast-iron system Fe-O-C-Si-Mn-P-S- and so on. In order to make an estimate of the oxygen solubility reason-

Jan 1, 1959

By H. H. Evinger, M. Muskat

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. 's Pace General Purpose Analogue Computer, and Sun Oil Co.'s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun's analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By M. Muskat, H. H. Evinger

Although the shooting of oil wells for the purpose of increasing production has been practiced since 1866, present-day shooting technique has been arrived at almost wholly by a process of trial and error. The difficulties attending either a theoretical analysis of the problem or an experimental attack become apparent when one actually embarks on a theoretical investigation or attempts to formulate an intelligent experimental program. The literature on the subject consists mainly of descriptions of current practice, scattered eye-witness accounts of events following the shooting of a well, and vague speculations on the mechanical processes involved. In contrast to quarry blasting, the results of oil-well shooting cannot be determined by means of visual inspection, and it is perhaps for this reason that only one attempt at what approaches a direct experimental attack has been reported in the literature.' In these experiments, charges of liquid nitroglycerin were exploded in holes drilled in a sandstone outcrop. In order to observe the character and extent of the resulting fractures, the rock was blasted away so as to expose the original shot holes. After all this had been done it was found impossible to distinguish the fracturing due to the original shots from that due to the subsequent blasting. The enlargement of the holes due to the pulverizing action of the shots was measured and an attempt was made to determine the effectiveness if sand tamping. Only five shots were made and few definite conclusions could be drawn. Some small-scale experiments to deter-mine the effect of tamping were performed by Snelling and IIalL2 Small charges (zo grams) of dynamite were detonated at the bottom of a cylindrical hole in a lead block and the resulting enlargement of the hole was taken as a measure of the effectiveness of the explosion. It was found that when the shot was tamped with a sufficient amount of sand or clay, the volume enlargement was approximately double that found when no stemming had been used. The properties of the explosives have been the subject of much study by the manufacturers, the U. S. Bureau of Mines, and various other agencies. For example, velocities of detonation for many commercial explosives are to be found in the Blasters' Handbook, issued by the Du Pont company. Many other properties are given in a treatise on the subject by Naoum.~ The shock wave that accompanies the detonation of high explosives has been studied photographically by Payman4 and others. The hydrodynamical theory of the shock wave has received much attention, and an extended theoretical treatment is given by Bateman.6 Two aspects of the well-shooting problem will be considered in this paper; namely, the fracturing of subsurface strata, and possible damage to casing. With respect to the former of these, several calculations have been made giving the stresses in the rocks surrounding the shot. In order to arrive at numerical results at all, however, it is necessary to introduce a great many simplifying

Jan 1, 1941

By J. A. Herbst, D. W. Fuerstenau

This paper examines the zero order production phenomenon in the context of the size discretized batch grinding model. A restrictive interrelationship between the selection and breakage parameters of the model, which is mathematically sufficient to ensure zero order behavior, is delineated. Based on this interrelationship, a scheme is developed for predicting the values of the selection and breakage parameters for all size fractions from a minimum of experimental data. To test this scheme, dolomite was ground in a laboratory batch ball mill. Successful simulation of the comminution behavior of this system was achieved using the batch grinding model with the parameter values obtained from the proposed scheme. Historically, a preponderance of comminution research has centered on attempts to relate breakage energy to the performance of comminution machines. Concomitantly, grinding data were interpreted almost exclusively in terms of inherently empirical energy-size reduction relationships1-3 or "laws of comminution"4- 6 which were based on highly oversimplified descriptions of the fracture process. In some instances, these relationships provide a crude basis for the correlation of experimental data, but, invariably, this approach is inadequate for meaningful process simulation. The control and optimum design of comminution circuits require a mathematical model capable of depicting the size reduction behavior of every size fraction for grinding conditions of technological importance. Energy-size relationships do not provide this detailed information. For example, an energy-size analysis for batch ball-milled dolomite has recently been completed in the authors' laboratories.7 This analysis provided a satisfactory correlation between the hypothetical size modulus, which characterizes only the finer portion of the size distribution, and the input energy. However, this relation did not constitute an adequate description of the complete system. In general, one of two distinct viewpoints toward simulation has been adopted in recent comminution research. The first approach focuses on the fracture of single mineral specimens, with the essential aim of representing the over-all process in terms of the breakage characteristics of individual particles and the characteristics of the stress field which the particles experience within the particular size reduction device. As illustrated by Harris's review,' the actual incorporation of single-specimen fracture information into a description of the behavior of a multiparticle comminution system has seldom been attempted. The only model to accomplish this incorporation was the one developed by Schönert.8 The Schonert model treats single-passage grinding machines in terms of a distribution of effective loads acting on a particle, a distribution of required particle breakage energies, and the breakage product distribution. However, the use of single-particle fracture behavior to derive models of the size reduction process is at present limited to machines in which the particle residence time is approximately equal to the time required to apply stress. As a result, Schönert's analysis cannot be used to advantage to simulate the complex environment which prevails within a tumbling mill. For multiple-passage systems a second approach to the description of comminution processes has been more fruitful. This approach entails the formulation of a mathematical model which is phenomenological in nature in that it lumps together the entire spectrum of stress-application events which prevail in a system under a given set of operating conditions. The appropriately defined average of these individual events is then considered to characterize the over-all breakage properties of the device. Thus, to analyze the performance of a tumbling mill, the manner in which the particles of a particular size (or size fraction) are stressed need not be distinguished. Instead, a single parameter is assumed to represent the resistance of that size to fracture, given the average grinding environment which exists in the mill. The isolation of such a parameter and a related set of quantities, which constitute the breakage product size distribution for the average event in this size fraction, allows the formulation of physically meaningful descriptive equations capable of yielding precise and detailed information for simulation.

Jan 1, 1969

By Y. C. Liu, G. A. Alers

The anisotropy of Young's modules has been measured in a series of Cu-Zn alloys containing from 1 to 28 wt pct Zn and cold-rolled to 97.5 pct reduction in thickness. These modulus data show a transition in texture as a function of zinc content. In alloys containing 3 pct Zn or less, the texture is essentially that of copper. A transition is clearly seen to develop in 5 and 8 pct Zn alloys, and to have been completed in a 12 pct Zn alloy. Increasing the proportion of zinc to 28 pct does not produce any further changes in texture. The ease and clarity with which this texture transition can be seen in the modulus data is in great contrast with the inccertainty in the visual detertiination of the range of texture transition from a series of pole figures. It is also shown that the rolling texture of the high zinc content alloys cannot be a one-COIIIponenl texture, characterized by the (110)(112) ideal orientations, as usually assumed. A second, quite important component must also be present. Furthermore, the present data are inconsistent with matrix orientations on which the "oriented growth" hypothesis of the Formation of recrystallization textures is based. THE rolling textures of binary fcc alloy systems have generally been considered to lie between two terminal textures. One of these terminal textures is the copper type and the other is the 70:30 brass type. Alloys of intermediate solute content exhibit a texture which is said to be a transition between the two terminal textures. On the basis of efforts to correlate rolling and recrystallization textures, two concepts have been advanced in the literature on the nature of these transition textures. One school1 suggests that the addition of alloying elements, e.g., zinc, causes a gradual rotation about one of the (111) poles from the (358)( 523) ideal orientation of the copper-type rolling texture to the terminal {1 10)( 112) ideal orientation used to describe the rolling texture of 70:30 brass. This concept is depicted in Fig. 1 with the angle of rotation corresponding approximately to the zinc content and is designated here as the "rotational concept", since the ideal orientation of the transition textures varies continuously with alloy content. The other concept,' the "mixture concept", suggests that the copper-type rolling texture is a two-component texture. {358) (523) and {110)(112). The addition of alloying elements affects only quantitatively the relative amounts of these two components—a decrease in the amount of material in the {385}(523) orientation and an increase of that in the {110)(112) orientation with increasing solute content. An experimental distinction between these two concepts is essential to a better understanding of both the mechanism of formation of rolling textures and the subsequent formation of recrystailization textures in fcc metals. Because of the lack of resolution inherent in pole figures, it has not been possible to differentiate between the two concepts on the basis of this data. Both concepts, in fact, make use of the same set of pole figures but interpret them in a manner acco-rding to the view held.'" Experimental results obtained from inverse pole figures or selected-area electron diffraction3j4 simply -yield more refined pole figures but do not eliminate the ambiguity of interpretation. Quantitative measurement of an entirely different, orientation-dependent property must thus be considered

Jan 1, 1967

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970

By G. Aertsen

THE CHAIRMAN (HENRY D. HIBBARD, Plainfield, N. J).-This excellent paper fills a gap in our Transactions and is most acceptable. In the early days another way of casting tire ingots, sometimes called cheeses, because of their shape, was to use a 22-gage sheet-iron cylindrical can for each ingot of the proper size to give the weight desired. These cans were bottom cast in groups, usually of four, each can being surrounded by a heavy iron ring somewhat taller than itself the top of the can being covered by a circular cast-iron plate having a small conical riser in the center, about 2 ½ in. in diameter at the bottom and 10 in. high. The top plate was clamped down to resist the upward pressure of the fluid metal and the space between the can and the outer ring, usually about 2 in. wide, was filled with dry sand. The riser permitted the escape of some of the air displaced by the steel and also increased the pressure in the steel when the mold was filled, and so diminished somewhat the tendency for gas holes to form. But little was known of segregation and pipe in those days, though the center of an ingot was understood to be the worst part, and it was separated in part in the disk which was punched out in perforating the ingot. This disk was about 8 in. in diameter and from ¾ to 2 in. thick, the variation in thickness being to rectify the weight. When an ingot was too -heavy, a thicker disk-was made by not driving the punch in quite as far as when the ingot-weight was right. Then the bloom was turned over and the punch driven in on the other side, which finished the punching and detached the disk. The tire bloom was then" becked" and later reheated and rolled as described in the paper. The forging was done with a 10-ton double-acting steam hammer. The steel generally speaking had lower carbon, from 0.45 to 0.55 per cent., than tires today have, and the tires were smaller, the most common size of ingot weighing 1,060 lb. each. BRADLEY STOUGHTON, New York, N. Y.-This paper was specially requested by the Iron and Steel Committee, because that Committee thought so important an industry should have its history written by one who was familiar with it, and before he had forgotten, or all the rest of the world had forgotten, its early stages. Mr. Aertsen has said that it is not an exhaustive research. I think it would not be any different if it were an exhaustive research, because our library made a careful attempt to find some written light on the history of these tires, but very little was found.

Jan 4, 1917