Search Documents

By P. D. P. Hamilton

In any mining district where benefication of the ores is practiced, one can usually observe several types of flow sheets even though the various producers are milling ore from the same geological formations. It is obviously impossible to describe all the mills in the Porcupine district. However, the following description of some of them is of particular interest in that it shows where one mill has paid particular attention to corduroy blanket practice; one to gravity concentration of sulfides for intensive cyanidation of the values therein contained; one to flotation of values and cyanidation of this product only; and others where small variations of standard all-slime cyanidation practice prevail. In all cases it will be seen that cyanidation is the basic principle. Discussions involving the difference in the flow sheets and the reasons for them will always be of value to those interested in the art. The author of this article, however, believes that such discussions should originate from the operators of the mills under discussion. For this reason no comparisons or discussion will be included in the description of the mills mentioned. Should any reader of this article obtain information therefrom which will be of value to him in helping to solve his own particular problems, the author will consider that the article has satisfactorily served its purpose. All values mentioned throughout this article are based on the value of gold at $20.67 per ounce. Coniaurum Mines, Limited The ore of the Coniaurium mines consists of a mineralized schist and quartz containing about 2.5 per cent sulfides. Owing to the low grade of ore developed in the mine, extreme care has had to be exercised throughout the entire mining and milling operation in order that an operating profit might be obtained. The management, however, has been able to keep costs down, with the result that at present the outlook for the property is considerably brighter than it has been in the past. This is partly due to the fact that it is now known how to mine and treat

Jan 1, 1935

By T. M Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the 'active masses' of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-' that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By Ernest F. Burchard

The Pao deposits of iron ore are in the State of Bolivar, Venezuela, near Upata, about 30 miles south of the Orinoco River and 90 miles east of Ciudad Bolivar. They were discovered 4 or 5 years ago and have not yet been developed to the stage of mining. In March-April, 1929, the writer devoted a week to the examination of these deposits. The maps, drill records and chemical analyses presented herewith were derived from original sources, and the field photographs were made by the writer. The petrographic and metallographic data are from notes by C. S. Ross and M. N. Short, of the U. S. Geological Survey, who have kindly collaborated in these special phases of the study. The Iron Obebodies Topography and Accessibility The deposits are in a region of low mountains representing northern outliers of the Guayanan Highlands. These mountains reach altitudes of 1800 to more than 2000 ft. above sea level, as determined by aneroid barometer. The iron ore is found on mountain crests that reach altitudes of 1915 to 1930 ft., and may be followed down precipitous slopes for 200 • to 300 ft. or more. The greatest vertical range in outcrop is nearly 400 ft., and drilling has indicated that the ore extends to this depth below the surface in one place, at least. The superior hardness of the iron ore accounts for the preservation of the local mountain crests with the intermediate valleys eroded in softer granitic rock. The deposits of iron ore are reached by a private road for automobiles branching northeast from the Ciudad Bolivar-Upata road, a distance of about 12 miles. This road was used in 1928-29 by trucks for transportation of food and camp supplies, gasoline, drilling equipment, etc., but was not suitable for the transportation of iron ore. Between Ciudad Bolivar and the iron-ore area the western two-thirds of the automobile road passes through nearly level, open country known as the savanna, largely used for grazing cattle. About 96 km. (60 miles) east of Ciudad Bolivar at

Jan 1, 1931

By T. M. Morris

THE rate of flotation of solid particles determines the percentage recovery of these particles which can be obtained during a given time interval. It is an established fact that the recovery is greatest in the fine sand size range and falls off on either side of this size range. It is also a fact that the history of the development of concentrating devices has been marked by a desire to recover the small particles: tables were developed to treat material too fine to recover in jigs; flotation recovers material too fine to be recovered on tables. As our ores become more complex and require finer grinding, a greater proportion is in the slow-floating size range. It is therefore of economic importance that the effect of size of particle upon rate of flotation be studied. Many studies have been made along this line. The present investigation attempts to quantify the rate of flotation by means of a rate equation, and then compares the effect of size upon the rate of flotation. It was found that the flotation rate constant increases with increase in diameter of particle in the size range smaller than the optimum size particle. The flotation rate constant decreases with an increase in diameter of particle in the size range coarser than the optimum size particle. This suggested two different actions taking place, and these are discussed. Suggestions for further work in order to improve the flotation rate of both fine and coarse particles are made. The usual method of expressing rate is to plot cumulative percent recovery vs time. If we knew the equation of this kind of curve we could replot it as a straight line, and the slope of the line would be an index of the magnitude of the flotation rate. It is easier to compare straight lines than curves. The basis used for obtaining the equation of the recovery vs time curve is the law of mass action. This law states that the "rate of a chemical reaction is proportional to the 'active masses' of the reacting substances present at any given time." This, of course, implies a constant temperature. We can modify this for our use by using the term flotation reaction instead of chemical reaction and the term floatable particle instead of active masses. dC Thus----— kc [1] where C denotes concentration of particles, t denotes time, k denotes a proportionality constant. If the exponent of C is 1, then we have a first order rate reaction. If the exponent of C is 2, then we have a second order rate reaction. For a first order rate reaction, we obtain, after integration, where k is again a proportionality constant and has the dimension of the reciprocal of time. C, is the original concentration or weight or percentage of floatable particles. C, is the concentration or weight or percentage of floatable particles remaining in the flotation cell after time t. If all particles of the mineral to be floated were capable of floating we could take C, as 100 and C, would be 100 - R, where R is the cumulative percentage recovery of mineral at time t. But it is not usual for all of the particles to be capable of floating, because of surface oxidation, etc. Therefore, we must introduce a factor x which is the percentage of un-floatable mineral. Hence the first order equation is It has been proposed by various workers1-' that this equation describes the flotation rate. More recently N. Arbiter4 states that a second order rate equation fits the recovery vs time curve more closely than does a first order rate equation. Morris- as discussed the evidence presented for this statement. It has been concluded that the first

Jan 1, 1953

By E. W. Davis

Iron-ORE beneficiation methods are determined largely by blastfurnace requirements. There are still many millions of tons of direct furnace ore in the Lake Superior district and blast furnaces are designed and operated for the most efficient use of this material. Beneficiated ore must be so prepared that existing furnaces may use it without alteration in design or radical changes in practice. Many attempts have been made to develop new furnaces or processes for smelting iron-ore concentrate not suitable for blast-furnace use, but these processes have gained little importance. It is, therefore, the endeavor in beneficiating iron ore to make a product that will give at least as good results as direct furnace ore in existing blast furnaces. The term "beneficiation," as applied to iron ore, does not necessarily mean concentration, but more accurately means "dressing up" the ore so that it is more acceptable to the blastfurnace operators. In modern blast-furnace practice the structure of the ore is quite as important as the chemical analysis. Certainly, the higher the iron content and the lower the silica, phosphorus and sulfur, the more desirable the ore bccomcs; but if the structure is bad, that is, if the blast-furnace gases can penetrate the charge only with difficulty, the ore is undesirable regardless of its analysis. This means that the ore should be as uniform in size as possible and free from fines, and also that the individual particles of ore should be pervious to the reducing gases of the furnace. Structure and purity are the primary requirements for a furnace ore and structure is just as important as purity. Iron-ore beneficiation processes can be divided, therefore, roughly into two main classifications: (1) processes that primarily improve the structure, and (2) processes that primarily improve the chemical analysis. During the past 10 years approximately 25 per cent of the ore shipped from the Lake Superior district has been beneficiated. Of this about half has been crushed and screened, a simple operation that primarily improves the structure but in some cases also improves the analysis slightly. The other half of the shipment of beneficiated ore, amounting to an average

Jan 1, 1935

By A. W. Hahn

THE importance, to geologists and metallurgists, of knowing the mineralogical forms in which the silver occurs in ores has increased during the past few years, and will continue to increase as long as working hypotheses are converted into proved theories and rule of thumb methods are supplanted by scientific data. The methods used for the determination of these silver minerals have been: (1) careful study of polished ore sections with the microscope, and more recently, (2) metallurgical separation of the ground ore by flotation, tabling and panning, supplemented by microscopic examination of these separated minerals, and chemical analyses. During the course of some experimental work carried on by the testing department of the International Smelting Co. and myself, it becomes important to determine, in a general way, the distribution of the silver values in the minerals, as they exist in Tintic Standard and North Lilly siliceous oxidized lead-silver ores. These mines are in the East Tintic Mining District, State of Utah. In this work the second method was used. Differential flotation tests were run, separating the sulfide from the oxidized minerals, and the products were assayed. Various concentrates were carefully panned and the separated products assayed; special samples of ore were selected and assayed. The microscope was used only for the purpose of determining whether the individual minerals were in the so-called "free" state.

Jan 1, 1929

By K. L. Komarek, P. F. J. Landler

Synthetic polycrystals of wustite were reduced ilz H2-H2O mixtures over limited roncentration ranges wiltun the wustite. field and the weight changes were continuously followed with a McBain quartz spiral balance. The reduction was. found to be controlled by a combined surface plus solid-state diffusion reaction. The solid-state diffusion had an activation energy of 38 kcal. Self--diflusioities of iron decreased with itzcreasing vacancy concentration. The activation energy of. the surface reaction runs different tor- different samples. The surface reaction-rate constan increased with increasirzg vacancy concentration. THE reduction of the oxides of iron has been studied for many years. Edstroem' has summarized the early work and has provided much information on the reduction of magnetite and hematite by hydrogen and carbon monoxide. More recent summaries are those by smeltzer2 and Themelis and Gauvin.3 Most investigators have reported that the iron metal which forms the outer layer during gaseous reduction is rather porous. According to Kohl and Engel14 the formation of such a porous iron layer depends on the properties of the underlying wiistite layer, on the reaction of the gas with the wustite surface, and on the transport of matter through the wustite layer. McKewan, Quets, Wadsworth, and Lewis, and Knacke 10 have found that, if a porous iron layer is formed, a surface reaction between gas and wustite at the bottom of the pores controls the rate of reaction. Seth and ROSS 11 and Warner 12 have pointed out that the influence of the gaseous pore diffusion through the porous iron layer cannot be neglected. It has further been shown that the wiistite layer formed during reduction is dense and that transport of matter across the layer occurs only by solid-state diffusion of iron ions.13,14 The solid-state diffusion rates observed by Edstroem and Bitsianis 14 and the surface reaction rates observed by Quets eta1.' show that an interaction of the two steps in controlling the reaction rate has to be considered. In this investigation the reduction of wustite was studied with respect to the interaction of the two steps, isolated from any other effects, by reducing wustite within the wustite field from higher to lower oxygen concentrations with H2-H2O gas mixtures. A similar study with CO-CO2 mixtures has been performed by Levin and wagner.15 Fused synthetic wustite polycrystals were reduced in steps of 0.4 wt pct from 24.4 to 23.2 wt pct 0 and over a temperature range from 700" to 1050°C. A few tests were also conducted with reduction steps from 24.4 to 23.6 wt pct 0 and 24.5 to 23.2 wtpct0. The Fe-O phase diagram is shown in Fig. 1 where the composition of the gas phase in equilibrium with the condensed phases is plotted as pct H2 vs the temperature. A careful study of the literature led to the conclusion that the fully drawn equicomposition curves (in wt pct O) in the wustite field used by Edstroem 1,16 and other authors needed some correction. Based on results by Darken and Gurry17 (shown as open circles) and on some of our own data, four corrected curves for 23.2, 23.6, 24.0, and 24.4 wt pct O were calculated (drawn as dashed lines in Fig. 1) which should replace the fully drawn equicomposition curves. MATERIALS AND APPARATUS Materials and Specimen Preparation. Wustite was prepared from iron sulfate (Fisher Scientific Co., New York) which had a purity of over 99.92 pct, with small amounts of manganese, copper, and zinc adding up to 0.03 pct. From the aqueous solution iron oxalate was precipitated and decomposed to magnetite according to Economos. 18 The magnetite powder was pressed into cylinders and sintered in vacuum at 900°C for several hours. The sintered compacts were placed in a platinum crucible of 2.5 cm diam which was fitted into a high-purity alumina crucible and then inserted into the center of the graphite heating element of an electric resistance furnace.lg The furnace was evacuated to below 1 p Hg and the magnetite sample was slowly heated. The evolution of gases during heating deter-

Jan 1, 1967

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

By N. E. Brown, F. L. Versnyder

THE apparent dependency of the electrical characteristics of hexagonal crystalline selenium on microstructure has aroused much interest in microscopical studies of selenium. Microscopic observations on the crystallization of selenium have been made by Escoffery and Halperin,' P. H. Keck,' and other investigators. It is the purpose of this paper to discuss the microstructural changes observed on polished cross-sections of single layers of selenium after various heat treatments. Observations were also made on crystallization of the free-surface layer of these deposits. In general, all of the transformations studied were either transformations of the vitreous selenium to hexagonal selenium or micro-structural transformation of the hexagonal selenium itself. Procedure The selenium used in this work was obtained from the American Smelting and Refining Co. and was approximately 99.96 pct pure. An intentional impurity of 1 part per 2,000 of bromine was added to the material prior to evaporation. A thickness of approximately 0.002 in. of this selenium was vapor deposited on an aluminum base plate. The maximum plate temperature during the vacuum vapor deposition was 140°C. Mounting of the cross-sectional specimens for metallographic study could not be done in plastic mounting media, as is customary, since temperatures in excess of 50°C would cause unwanted transformations. Consequently, a simple clamp-type device was used to mount the specimens for preparation. All grinding operations were then done carefully by hand in order that the specimen not become heated during this operation. Wet polishing was done on the conventional metallographic polishing laps, using successively finer grinding powders. An extremely careful polish is necessary, since observation and micrography of the specimens are done in the unetched condition under polarized light. The two observations of crystallization made on the free surface of vitreous selenium deposits (Figs. 4 and 5) were made on surfaces which were perpendicular to the cross-sections studied. These free-surface layers were examined directly, i.e., no pre- vious metallographic preparation, as obtained from the vacuum vapor deposition. Microscopic Observations A study was made of polished cross-sections of the vitreous selenium as-deposited. It was noted that in all cases there was columnar crystallization adjacent to the base plate, which appeared to occur during the vacuum deposition process. This observation has also been made by Keck? It also was observed that vagrant spherulitic crystallization occurred in the vitreous selenium. The term "vagrant" is used, since these spherulitic grains appear to crystallize at random throughout the vitreous selenium during the vacuum deposition process. Columnar crystallization at the A1-Se interface and a typical spherulite observed in a polished cross-section of "as-deposited" vitreous selenium may be seen in Fig. 1. Cross-sectional samples of vitreous selenium studied after heat treating individual samples for 20 min in 10" steps from 80" to 220°C revealed that crystallization—in this case, columnar crystal growth —proceeds from the aluminum base plate to the surface of the specimen (Fig. 2). Crystallization was microscopically observed to be complete after the 130°C heat treatment. Visual examination of the free surface of the specimen after the 130 °C heat treatment revealed the readily recognizable grey appearance of the completely crystallized selenium, in corroboration of the microstructural observations. No microstructural transformations then appeared to take place between 130" and 190°C. At 190°C the beginning of recrystallization appeared and proceeded until the columnar grain structure had been completely transformed to equiaxed grains between 210" and 220°C (Fig. 3). Naturally, the grain size of the recrystallized grains at the lower temperatures (190" to 210°C) was smaller than is illustrated in Fig. 3. In addition, polished cross-sections of deposits heat treated at 140°C for 10 min to cause complete crystallization and, subsequently, heat treated in 10" steps from 80" to 220°C for 20 min were studied. As expected, no microstructural transformations took place until the beginning of recrystallization was observed at 190°C. A comparison with the previously studied specimens revealed that recrystallization proceeded almost identically in the two experiments although in the first case the deposits were vitreous prior to the series of heat treatments and in the second case they had been crystallized by a previous heat treatment. By heat treating for longer times (180 min) at lower temperatures, the

Jan 1, 1956

By Henry A. Stiff, and Lawrence E. Davis

The authors previously presented a method for predicting the tendency of oil field waters to deposit calcium sulfate. The present paper gives a similar method for calcium carbonate. Methods for predicting calcium carbonate scaling tendencies in fresh waters have been available for some time, but these could not be used for brines. By experimentally deriving the value of the K term in the Langelier equation, a method has been developed which applies to waters of high salt content. A statistical study is included which shows that the experimentally derived values of K are in good agreement with actual conditions. Several applications of the final equation to production practice are given. INTRODUCTION The authors previously presented a method for predicting the formation of calcium sulfate scale in oil field waters.' Although calcium sulfate deposition is important in production operations, the majority of scale problems involve calcium carbonate. The present communication discusses a method by which the formation of this type of scale in oil field waters can be predicted. Calcium carbonate precipitation is caused by a shift toward carbonate in the carbonate-bicarbonate-carbon dioxide equilibrium. When equilibrium shifts in the other direction, the precipitate goes back into solution. Since there is usually considerable delay between the establishment of an equilibrium and the precipitation or solution of calcium carbonate, unstable conditions exist in which a water will precipitate or dissolve calcium carbonate on standing. Tillmans? who did a major part of the early work on carbonate scaling, pointed out that the condition of equilibrium not only indicates the tendency of a water to scale but also is an indication of its corrosive properties. Previously precipitated calcium carbonate combines with iron to form a dense crust which inhibits corrosion. If the water tends to dissolve carbonate, the scale becomes porous, and electrolytic corrosion takes place. Tillmans1 work was extended by several investigators until in 1934 Langeliers developed an equation setting forth the conditions of carbonate equilibrium. By the use of this equation the pH of a water at equilibrium can be calculated. If the actual pH is higher than the calculated pH, the water has a tendency to form scale. If it is lower. the water has a tendency to be corrosive. Langelier's equation can be expressed in a simple form as follows: SI = pH-pCa-pA lk-K where: SI is the stability index. A positive index indicates scale formation. A negative index indicates corrosion. pH is the pH of the water sample, as actually determined. pCa is the negative logarithm of the calcium concentration. pAlk is the negative logarithm of the total alkalinity. K is a constant, the value of which depends on the total salt concentration and the temperature. This equation has been shown to apply to waters with totaI solid concentrations as high as 4.000 ppm. In fact, control of fresh water treatment by means of this equation has been standard text-book practice for a number of years. Nomographs have been worked out so that the stability index of a fresh water sample can be determined in a matter of minutes. Most oil field waters, however, contain well over 4,000 ppm of salts and for this reason the usual application of Langelier's equation can not be made. By an empirical method we have extended the application of the Langelier equation to waters of high salt concentration. By the use of this equation the tendency of oil field waters to deposit calcium carbonate can be predicted.

Jan 1, 1952

By O. P. Quist, S. H. Carpenter

The internal friction of single-crystal LiF has been investigated as a function of crystal orientation, while simultaneously applying a static compressive load. Three different crystal orientations were used, these being samples with the (100), (110), and (111) directions along the sample length. Results show the internal friction measured to be similar in appearance but different in magnitude for the (100) and (110) samples. With both orientations, application of a static stress caused an increase in the amplitude-independent damping, which recovered with time. The amplitude-dependent damping was found to first decrease with load up to the yield stress and then increase rapidly. Samples of the (111) orientation were found to have no measurable internal friction even when loaded up to 3.0 kg per sq mm. These results are discussed in terms of current theories of internal friction in ionic crystals. This paper presents the results of an investigation of the dislocation mobility and dislocation motion in high-purity single-crystal LiF at applied stress levels up to the yield stress. Internal friction measurements of the dislocation damping while simultaneously applying a static compressive load was the experimental technique used. LiF crystals much prefer to slip on the (110) set of slip planes. However, with a suitable stress distribution they can be forced to slip on the {100} set of slip planes.' For both sets of slip planes the slip direction is the same, namely (110). The object of this investigation was to try and learn more about the dynamical properties of dislocations on the different slip systems in LiF crystals. EXPERIMENTAL PROCEDURE Dislocation damping was measured, in terms of the log decrement, using a five-component marx2 composite piezoelectric oscillator. The apparatus used allows one to measure the dislocation damping while simultaneously applying a static compressive load on the sample. A schematic of the apparatus used is shown in Fig. 1 and a complete discussion of its construction and operation is given elsewhere.3 All measurements were made at room temperature with a longitudinal resonant frequency of approximately 50 kc per sec. Damping measurements were made using longitudinal vibrations with strain amplitudes from up to 10. Static loads up to 3.0 kg per sq mm were applied to the sample while the damping was being measured. Samples used in this investigation were high-purity single crystals of LiF purchased from the Harshaw Chemical Co. All samples were approximately of an in. square and were hand-ground in length to one-half wavelength to match the resonant frequency of the driver and gage quartz crystals. Samples of three different crystallographic orientations were used, namely, crystals with the (loo), (110), and (111) direction parallel to their length. The magnitude of the damping is a direct measure of the area on the slip planes swept out by dislocations during a complete oscillatory cycle. With a sample of the (100) orientation the maximum applied shear stress, due to longitudinal vibrations, is on the (110) slip planes with zero shear stress on the (100) slip planes. Thus, damping measured from a (100) sample is due entirely to dislocation motion taking place on the (110) set of slip planes. Similarly, for a sample of the (111) orientation there is zero shear stress on the (110) set of slip planes and the damping measured from a sample of this orientation is due entirely to dislocation motion on the (100) set of slip planes. Samples of the (110) orientation will have a component of shear stress on both sets of slip planes and

Jan 1, 1969

By Rees D. Rawlings, C. W. A. Newey

The aging characteristics of an Fe-11 at. pct Mo alloy have been studied by means of light metallography together with density, Young&apos;s modulus, and hardness measurements. The results were consistent with the precipitation of a single intermetallic compound during aging; overaging was slow relative to that in other iron-based binary alloys. The solution treatment temperature had a small effect on the rate of hardening whereas deformation prior to aging had a marked effect on both the rate of hardening and the peak hardness. The density data indicate that the compound precipitated is Fe3MO2 and not the Laves phase Fe2Mo. Analysis of the modulus and density results gave values for the time exponent for precipitate growth of approximately 1.0 and 1.5 for the alloy aged with and without prior deformation, respectively. DETAILED studies of precipitation hardening in bcc matrices have been confined largely to the effects of carbides and nitrides. In view of this and the growing technological interest in intermetallic compound strengthening, e.g., in maraging steels, a study of precipitation in iron-based alloys with a low interstitial content has been undertaken. This paper is concerned with the aging behavior of an Fe-11 at. pct Mo alloy; the mechanical behavior of the alloy will be reported later. The early work of sykes on Fe-Mo alloys showed that precipitation of the intermetallic compound was accompanied by an increase in hardness and a decrease in volume of the material. More recent surveys of the strengthening associated with precipitation have been made3-5 and, in particular, Elsen and wassermann4 showed that deformation prior to aging increased the rate of hardening. These latter workers also followed the precipitation process by means of dilatometry, electrical resistivity, and lattice parameter measurements. Their results confirmed that there is a decrease in volume on aging. Except for the work of Hornbogen on an Fe-20 at. pct Mo alloy, neither clustering nor the precipitation of a nonequilibrium phase has been observed in Fe-Mo alloys. Studies of alloys of lower molybdenum content475 indicate that the equilibrium intermetallic compound is precipitated during aging. However, there is some doubt concerning the nature of the equilibrium precipitate phase. According to the phase diagram constructed by Hansen,8 the phase should be precipitated. This phase has a rhombohedra1 crystal structure which is characterized by the formula Fe706,&apos; although the composition of the molybdenum-rich boundary corresponds approximately to Fe3Mo2. The version of the diagram proposed by Sinha, Buckley, and Hume-Rother indicates that the A phase, a Laves phase Fe2Mo, should be precipitated. Their observation of a Laves phase supports the earlier findings of Bechtoldt and Vacher,13 although, in a recent study of the system by means of diffusion couples, Rawlings and Newey did not detect the phase. The work presented here describes the effect of solution-treatment temperature, aging temperature, and prior deformation on the aging characteristics of the alloy as revealed by light metallography together with hardness, density, and Young&apos;s modulus measurements. In addition the density data are used in an attempt to determine the compound precipitated during aging. EXPERIMENTAL PROCEDURE A 29-kg ingot of the alloy was cast at R.A.R.D.E., Fort Halstead, from deoxidized, Japanese electrolytic iron and sintered molybdenum. The ingot was homogenized for 6 hr at 1473°K and then worked, with intermediate anneals, into 6- and 16-mm-diam rods and 6-mm plate. Chemical analysis of the alloy gave, wt pct: Mo, 17.5 (11 at. pct); C, 0.003; Si, 0.002; S, 0.005; P, <0.002; and02, 0.0098. Solution treatments were carried out under a dynamic argon atmosphere in a vertical, "crusilite" element, furnace which had a facility for rapid quenching into iced water. Except for the study of the effect of solution treatment temperature, all specimens were solution-treated at 1573" * 2°K for 1 hr. Salt baths were used for the aging treatments. Specimens for hardness, density, and Young&apos;s modulus measurements were produced, after heat treatment, from the stock rod or bar using a precision silicon carbide slitting wheel. As described later, the quenching treatment produced local plastic strain in the stock material; consequently, care was taken to ensure that the specimens were not prepared from these regions. Those specimens used in the studies of the effects of prior deformation on the aging behavior were strained in compression in a Denison universal testing machine. Specimens for light metallographic observations were mechanically polished on successively finer grades of diamond paste down to and then etched in either alcoholic ferric chloride or in a 2 pct nital solution. Vickers diamond pyramid hardness data were obtained using a 30-kg load. At least five impressions were averaged for each determination. Density measurements were made using a displacement technique in which each specimen was weighed in air and in dibromoethane at 296°K. The specimens were cylindrical and weighed 3 to 4 g; all weighings were made on a balance reading to 1 x 10"5 g. For each specimen the mean value of five weighings was used to calculate the density. The density of the dibromoethane was determined using the displacement procedure and a standard nickel specimen. The error in an absolute density value was estimated to be HI.01 pct. To obtain the density as a function of aging time a single specimen was used and the density meas-

Jan 1, 1969

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,&apos; the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,&apos; the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By C. H. Lee, R. Maddin

The diffusion rates of Ag110 in cylindrical single crystals of 99.99 pct pure silver, which were twisted to a total surface strain of 0.91 during the diffusion anneal at temperatures of 700°, 750°, and 800°C, were measured by sectioning and counting as a function of the strain rates. The ratio of the diffusivities while strain ing occurred (Ds) to those of the unstrained specimens varies linearly with the rate of twisting and attains values of near 100 for some of the rates used. The enhancement of diffusion by straining is inversely proportional to the temperature at which diffusion occurs. The activation energy for diffusion determined from the data plotted as a function of the rate of twisting decreases from 44,090 cal per mole for zero strain, to an asymptotic value of 21,000 cal per mole for the strain rates of 22 x it)"5 see-l. Qualitative explanation for the observations based on the generation of nonequilibrium number of defects by plastic deformation will be discussed. The initial research of Buffington and cohen1 on self-diffusion in a iron under compressive stresses contributed the first quantitative information concerning the effect of applied stresses on diffusion. These results were obtained from radioactive Fe55 plated on one of the horizontal surfaces and compressing the large-grained specimens while the diffusion-anneal was occurring. Enhancement of diffusion of a maximum of seventeen times was observed provided the strain was in the tertiary stage of creep and the rates of straining were at least as fast as rates used in the normal creep test. On the other hand, Darby, Tomizuka, and Balluffi,2 extending silver single crystals up to 30 pct elongation at rates of straining about equal to those used by Buffington and Cohen observed no effect. For the past two and a half years at the University of Pennsylvania, we have been investigating the effect or torsional strains on self-diffusion in silver single crystals. If enhancement is observed as has been reported1 a possible explanation may be based upon the generation of fairly large numbers of point defects and their role in the diffusion process. Hence, since torsion should produce an abundance3 of point defects, an increase in the diffusivity while the crystal is being twisted should easily be measured. EXPERIMENTAL PROCEDURE Our research uses single crystals of silver prepared from 99.99 Ag by the Bridgman method in a dynamic vacuum of less than 25 µ. As grown, they are about 25 cm long by 1.3 cm in diam. The crystals are cut into 7.5 cm lengths with a jeweler&apos;s saw and machined to the shape shown in Fig. 1. The test length of the crystal is machined to a 0.6 cm diam after which the ends are masked and the test section etched heavily in HNO3, and KCN:(NH4),S2Os , solution to remove the effects of machining. The specimen is then annealed in vacuum for 8 to 12 hr at 800°C to remove any residual stresses and also to recrystallize the end sections. The recrystallized ends are necessary since experiments showed that single-crystalline end sections are too soft to transmit the desired torque. Occasionally, recrystalliza-

Jan 1, 1960

By J. D. Lindner, Gene E. Roark

Waterflooding operations in the Langston-Kleiner field. Young County, Tex., are described. Widespread application of formation fracturing has been practiced in both producing and injection wells. Field performance data arc cited which indicate than no detrimental effect on sweep efficiencies and that probable benefits in imectivily have resulted from the fracture treatments. I N T R O D U C I O N This paper is a report on a waterflood operation which is being carried out in the Lanpston-Kleiner field located in Young County, Tex. The oil reservoir aflected by this flood operation occurs in a Strawn sand member at an approximate depth of 3.550 ft subsurl&apos;ace. The operators of&apos; the project are Kleiner Estate. Turncr. Fiske. and West who are hereinafter collectively referred to as the Operators. Although the operation is unusual in several respects, the distinctive feature of this flood has been the widespread application of hydraulic formation fracturing treatments as a means to improve productivity and injectivity of the wells. It shall he the purpose of this paper to present basic information regarding the reservoir characteristics. op- craling practices, and waterflood behavior so that conclusions may be drawn concerning the effects which the fracture treatments have had on the performance of this water flood to datc. DEVELOP MENT Development of the 3,550 ft Strawn sand reservoir occurred during 1951 and 1952. The early development occurred on the Langston and Davis leases which arc in the northern region of the Operators&apos; holdings and the wells were drilled on 20-acre proration units according to the field rules. However, studies of the economics of this program. coupled with the decision to proceed with pressure maintenance by water injection. resulted in the adoption of wider spacing in the later stages of development. This variation in spacing is apparent upon inspection of Fig. I upon which only the 3,550-ft Strawn sand producing and injection wells have been located on the Operators&apos; properties. The development to the north of the operators leases is Ihe Garvey Strawn field and that to the south is the Taylor Strawn field. It wits determined that unitization of the leases to he involved in the waterflood program was not feasihle. Consequently. a system of offset injection wells, or lease line injection wells, was adopted from place to place as required to protect correlative rights in the program. This resulted in a dispersed array of injection and producing wells with relatively close proximity of wells along lease line areas and wider spacing toward

Jan 1, 1956

By H. R. Stahl

The disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat; is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. Dry Crushing The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 23/4 tons to 81/4 tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943

By H. R. Stahl

The disseminated lead district of Southeast Missouri lies 70 miles south of St. Louis. The only metal of economic importance in the ore is lead, but minor amounts occur of iron, zinc, copper, cobalt, nickel, silver and cadmium. These minor metals, as might be expected, tend to concentrate in both the flotation and table middlings. In the past, some zinc has been recovered by differential flotation. The silver and cadmium tend to associate with the zinc, and some recovery is made of these two metals at the smelter. The lead occurs as galena, or lead sulphide. The minor metals are also present as sulphides. The presence of oxidized lead is suspected, but has not been definitely proved. The gangue is chiefly dolomitic limestone, with small amounts of sandstone and shaly glauconitic and chloritic minerals. The ore contains about 3.25 per cent lead, occurring as galena disseminated through the gangue. Some of the galena is very finely disseminated, and the mineral in the gravity tailings, or chat; is seldom or never in the free state. The method of treatment of the ore has been evolved over a period of 75 years; hence probably is not far from correct. The milling processes have tended toward simplification during the past 15 years, but recoveries have never been sacrificed for the sake of simplicity. In many cases, simplification of flowsheets has led to better recoveries and operating economies. A simplified flowsheet is shown in Fig. I. The St. Joseph Lead Co. operates four mills in the Flat River district, with a normal total capacity of about 21,000 tons per day, divided as follows: Federal mill, 11,000 tons; Leadwood mill, 4500 tons; Desloge mill, 3400 tons and Bonne Terre mill 2400 tons. The methods of concentration used at these plants are similar in principle; they differ mainly in details and in the type and size of the equipment used. The process of concentration may be divided into five main steps; i.e., dry crushing, wet grinding, classification with its attendant desliming, tabling and flotation. A brief description of these processes will be given, noting important differences in the various plants, and also noting the more important changes or developments of the past few years. Dry Crushing The run-of-mine ore is hoisted in skips, the capacity of these skips ranging from 23/4 tons to 81/4 tons. At the Desloge plant, the ore is hoisted in 2-ton mine cars on self-dumping cages. All ore is hoisted at shafts adjacent to the various crushing plants, no ore being transported on the surface. Primary breaking at all the mills is accomplished with 9E Telsmith breakers. Preliminary screening is provided ahead of most of these crushers, either by station-

Jan 1, 1943

By J. E. Chappelear

We are concerned with the problem of calculating the forces produced by passing waves on a submerged object (in particular a drilling barge) located on the ocean floor. We employ the linearized theory of waves (the Airy1 theory), since solutions are generally more easily obtained in such a theory. It will be indicated how an approximate solution to the problem can be obtained for waves of finite height by use of a linear combination of Airy waves. We shall assume the submerged object has an infinite length, thus neglecting diffraction and making the problem two-dimensional. We find that there is not a considerable difference between our solution and the usual engineering solution. The force, as a function of time, is plotted in Figs. 4 and 5, together with the usual solution for easy comparison. So far, no experiments have been found to compare with the results. As will be shown, the calculations can be extended to waves of finite height (Stokes2-Struik3 waves) in an approximate fashion. This can be done by calculating the force produced by each Fourier component of the wave, separately, and omitting the coupling between the various harmonics produced by Bernoulli&apos;s theorem. The problem and its boundary conditions will be briefly stated. We seek a function, +, the velocity potential, which is harmonic, ?2?=0...........(1) and which satisfies the boundary conditions ??/?n =0 .......(2) (the normal derivative of + is zero) on the ocean floor and the sides of the barge, and s??/?y = ?..........(3) on the ocean surface, where s = g/w2........(4) The physical reasons for these choices and an interpretation of ? are given by Lamb.&apos; As previously stated, we assume also that the problem is two-dimensional. We set up our coordinates such that x = 0 is the center of the barge and y = 0 is the ocean floor. The coordinates are shown in Fig. 1, together with the location of the barge on the bottom. Our solution may be decomposed into a function which is symmetric about x = 0,?e, and one which is antisymmetric, +,, ? = ? + ?o...........(5) Thus directly above the barge we have as boundary conditions that for x = 0, ?o = 0, ...........(6) and ??e/?x = 0........(7) Now, far from the barge, we have that (for x positive and assuming the waves are incident from the left) ?e ? Ae cosh ky cos k (x + a) , . . . (8) and ?e ? Ao cosh ky cos k (x + ß) . . . . (9) where + means ". .. approaches ... for x large." Let us put Ae, Ao, and k equal to one, and remember that, in accordance with the derivation of Eq. 3, a sinusoidal time factor is to be supplied. Then we may rewrite Eq. 8 for ?e, and we find that

Jan 1, 1958

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By F. E. Buch

The smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The :smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pet moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pet oxide copper. The predominating minerals are chalco-cite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. General Description Flotation concentrate, containing 10 Pet moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and Spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which Prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been Set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1949