Search Documents

By J. M. Gaines, C. H. Herty

IRon oxide (FeO) plays an extremely important part in the manufacture of steel. In the open-hearth furnace and the Bessemer converter it is the chemically predominant compound and controls to a large extent both the operation of the furnaces and the composition and quality of their products. Almost all of the refining action is carried out through the medium of FeO, which oxidizes carbon, manganese, silicon and phosphorus. At the end of any open-hearth or Bessemer heat the steel contains dissolved iron oxide, which must be wholly or partly eliminated. The type of deoxidation product depends on the amount of dissolved iron oxide and on the deoxidizer used. After the heat has been deoxidized and while it is being teemed, iron oxide diffuses from the ladle slag into the metal, causing losses of deoxidizer and increase in iron oxide content of the steel. It is generally believed that non-metallic inclusions are responsible for a great many failures of steel in service and for decreased yield of steel during rolling. The basis of most non-metallic inclusions is dissolved iron oxide. This investigation was undertaken in order to determine the amount of iron oxide that will dissolve in iron under various conditions. Steel-making slags are complex and it has been thought best to determine solubility under simple slags as a first step. The study is being continued under slags whose compositions approach those of operating slags Previous Investigations The solubility of oxygen in iron has been determined by a number of investigators (see Table 1) but their effort's have been directed toward the

By W. P. Lass

Discussion of the paper of W. P. LASS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 103, July, 1915, pp. 1443 to 1447. ROBERT M. KEENEY, Somersville, Conn. (communication to the Secretary *).-There is not only a possibility of improvement in present methods of treatment of the byproducts of refining in the cyanide plant by the use of the electric furnace, but also in melting and refining of gold precipitate. This interesting paper by Mr. Lass shows an electric furnace in successful operation in a large plant for the treatment of by-products. Electric melting of cyanide precipitate is a cheaper form of treatment in many cases than any of the combustion methods now used because of the high cost of oil, coke or coal in many camps, while on the other hand electric power may be had cheaply, especially in a place where there is possibility of development of high-head hydro-electric plants for power purposes. Also, if the oil-fired tilting furnace is used for direct melting of the precipitate, as is the case at many small mills, a great saving in cost is made by the use of the electric furnace because of the high crucible cost in melting with the tilting furnace. A study of this paper indicates the cost of the operation approximately. Consider all the fluxes to be turned in as byproducts and coke at $18 per ton.

Jan 12, 1915

By H. Conrad, V. Damiano, J. Hanafee, N. Inoue

The effects of hydrostatic pressure up to 400 ksi at 25" to 300°C on the mechanical properties of three forms of commercial beryllium (hot-pressed block, extruded rod and cross-rolled sheet) were investigated. Three effects of pressure were studied: mechanical beharior under pressure, the effect of pressure-cycling, and the effect of tensile prestraining under hydrostatic pressure on the subsequent tensile properties at atmospheric pressure. For all three materials the ductility increased with pressure whereas the flow stress did not appear to be significantly influenced by pressure. An increase in the subsequent atmospheric pressure yield strength generally occurred as a result of pressure-cycling or prestraining under pressure, whereas either no change or a decrease in ductility occurred. The only exception to this was sheet material, which exhibited some improvement in ductility following a pressure-cycle treatment of 304 ksi pressure. The effects of pressure-cycling and prestraining were relatively independent of the temperature at which they were conducted. Stabilized cracks of the (0001) type were found in hot-pressed specimens and {1120) type in extruded and sheet specimens following straining under pressure. Also, pyramidal slip with a vector out of the basal plane, presumably c + a, was identified by electron transmission microscopy for extruded rod and for sheet strained under pressure. Small loops similar to those previously reported were found after straining at pressures of the order of 300 ksi. THE use of beryllium in structures is limited because of its poor ductility under certain conditions. Therefore, one objective of the present research was to determine if the ductility of beryllium at atmospheric pressure could be improved by prior pressure-cycling or prestraining under hydrostatic pressure. Another objective was to study the mechanisms associated with the plastic flow and fracture of the polycrystalline form of this metal with pressure as an additional variable. Since the early work of Bridgman,1 it has been recognized that many materials which are brittle at atmospheric pressure exhibit appreciable ductility when strained under high hydrostatic pressure. This effect has been reported for beryllium by Stack and Bob-rowsky2 and by Carpentier et al.3 and has been attributed to the operation of pyramidal slip systems with slip vectors inclined to the basal plane while cleavage or fracture is suppressed.4 That such slip may occur simply by the application of pressure alone without external straining (pressure-cycling) is suggested by the results on polycrystalline zinc5 and polycrystalline beryllium,6 where nonbasal dislocations with a vector (1123) were reported. A significant improvement in the ductility of the bee metal chromium by pressure-cycling has been reported.7 On the other hand, limited studies on the pressure-cycling of the hcp metals zinc67819 and beryllium6 indicated no improvement in ductility; there only occurred an increase in the yield and ultimate strengths. The study on beryllium was limited to hot-pressed material. Consequently, additional studies on the effects of pressure-cycling on other forms of beryllium seemed desirable, especially since for chromium some authors10 have been unable to detect any improvement in ductility while others find a large improvement.7 That the ductility of polycrystalline beryllium at atmospheric pressure might be improved by prior straining under hydrostatic pressure was suggested by the known beneficial effects of cold work on the ductile-to-brittle transition temperature in the bee metals. It was reasoned that, by straining under hydrostatic pressure, fracture would be suppressed, and during the propagation of slip from one grain to its neighbor dislocations with a vector inclined to the basal plane"-'4 would operate. Upon subsequent straining at atmospheric pressure, these dislocations with a nonbasal vector would continue to operate and thereby reduce the tendency for fracture to occur, by assisting in the propagation of slip across grain boundaries and by interacting with any cracks that may develop. It was recognized that maximum improvement in ductility would probably occur at some optimum amount of prestrain under hydrostatic pressure. If the pre-strain was too small, an insufficient number of dislocations with a nonbasal vector would be activated; if it was too large, internal stresses (work hardening) might increase the flow stress more than the fracture stress, or incipient cracks or other damage could develop. EXPERIMENTAL PROCEDURE 1) Materials and Specimen Preparation. The materials employed in this investigation consisted of hot-pressed block (General Astrometals, CR grade), extruded rod (General Astrometals, GB-2 grade with a reduction ratio of 8:1), and cross-rolled sheet (Brush S200, 0.065 in. thick). The analyses of these materials and mechanical properties at room temperature and atmospheric pressure are given in Table I. The grain size of the hot-pressed block was 15 to 16 µ, that of the extruded rod 10 to 11 µ, and that of the sheet 7 to 10 µ in the rolling plane and 5 to 6 µ in the thickness, all determined by the linear intercept method. Al-

Jan 1, 1969

By Cyril Stanley Smith

Although alloys of copper and silicon were examined several years ago,' and their excellent mechanical properties were shown, it was not until C. B. Jacobs 2 introduced manganese in small quantities to the alloys that they became of commercial importance. A few years ago The American Brass Company took over the patents and commenced to manufacture the alloy under the name "Everdur." The present study of the constitution of the ternary system was undertaken in order to reach a fuller understanding of the behavior of the alloy. Review of Previous WORK on the BinaRy Systems There have been no papers published dealing with the constitution of the ternary system, although some tests of the mechanical properties have been described," which indicate that there is a change in solubility with temperature. Copper-silicon System The copper-silicon system has been studied in detail by the author and is described in two papers published in 1928.V he portion of the diagram up to 8 per cent. silicon, as determined by this research, is reproduced in Fig. 1. The author's previous papers include a complete review of the work of other investigators and it is not necessary to deal further with this system here. Copper-manganese System The copper-manganese system has been investigated by several workers, notably Lewis,5 Wologdine,6 Sahmen7 and Schemtschuschny,

Jan 1, 1930

By L. F. Mondolfo, B. E. Sundquist

The crystallographic orientation relationships resulting when lead is nucleated from the liquid by Ni, Cu, Ag, and Ge were determined. For each nucleating agent several definite orientatioz relationships were found. These relationships seemed to be controlled by good symmetry relations and low crystallographic disregistry between mating planes. For any given nucleating agent the under colling for nucleation was found fairly constant and independent of the orientation relationship and consequent disregistry. It was also found that, upon re melting and refreezing the Pb, the orientation relationship was changed. These findings prove that crystallographic disregistry is not the controlling factor in heterogeneous nucleation from the liquid. The results of this investigation tend to confirm the theory presented in a preceding paper that heterogeneous nucleation starts with the formation of an adsorbed layer of nucleated metal on the nucleat-ing impurity. Evidence is given that cavities in the nucleating agent act as centers of nucleation. IT has long been known' that solid extraneous particles are active in catalyzing phase transformations that occur in a system, particularly condensation and crystallization. It is well established that these heterogeneities act as catalysts by providing surfaces upon which nuclei of the precipitating phase can form with activation energies smaller than those required for homogeneous nucleation. Numerous investigations have shown that in this process of heterogeneous nucleation: a) the nucleus forms with one, or several, definite crystallographic orientation relationships with the nucleating phase2-4 and b) that there is a small range of undercoolings or super saturations characteristic of the nucleation of a given solid on a given Substrate.5-10 Turnbull and vonnegut11 have developed a theory based on theories developed by Volmer12 and Turn-bull and Fisher1= for heterogeneous nucleation from gases and liquids, that relates the super saturation or undercooling required for nucleation to the dis-registry between the lattices of the nucleus and the nucleating agent. This theory predicts that nucleation should occur with the orientation relationship between the nucleus and nucleating agent that minimizes the disregistry. Further, it predicts that the undercooling or super saturation necessary for nucleation should be a function of the disregistry. Numerous investigations have dealt with the orientation relationships resulting from the condensation of vapors onto crystalline solid substrates2,3 and a few with the nucleation of one phase by a second phase in solidification4,14. Others have dealt with the supersaturation8-10 and undercooling5-7 associated with nucleation in condensation and solidification respectively. However, there is virtually no report that gives both of these factors for the same system. In this investigation a study was made of the undercoolings and orientation relationships resulting when Pb is nucleated from the liquid by Ni, Cu, Ag, and Ge. It was the purpose of this investigation to check the Turnbull-Vonnegut theory, i.e., the importance of crystallographic disregistry between nucleating catalyst and nucleated metal. The results indicate that disregistry is not an important factor in nucleation and that the nucleation process is probably somewhat more complex than current theories suggest. EXPERMENTAL PROCEDURE Small single crystals of nickel, copper, silver, and germanium were prepared from materials of four to five nines purity, and the Pb used was also 99.999+ pet pure. Cu and Ag single crystals were prepared by sealing small chips of Cu or Ag in an evacuated quartz capsule and heating the capsule at 2000°F for 1 hr before cooling. Nickel crystals of 200 diam were also prepared in evacuated quartz capsules, but melting was done by heating the capsules in an oxy-acetylene flame for a few minutes. These spheres were invariably polycrystalline so

Jan 1, 1962

By James C. Bayles

The ideal pressure-tube is obviously the one which combines the greatest strength with the least weight of material consistent with the uses for which it is designed or employed. The inside of the pipe is the first concern of the engineer. It should be cylindrical, smooth, and of the requisite capacity for the purpose in view. It should be in lengths as great as can be oonveniently handled, so that the couplings may be as few as possible. With the walls of the tube the engineer has no further occasion to concern himself than to make sure they are adequate to carry the internal and external pressures to which they will be subjected. It is as true of a pipe as of a truss, that when it is strong enough to give the requisite factor of safety, nothing is gained by having it stronger. Anything more than this means dead weight, which has to be paid for many times, first as material, and again and again in the costs of transportation and handling, until it reaches its place in the trench or on supports. In use it must be and remain tight against all leakage, and must sustain whatever is placed over or upon it, or suspended from it, without deformation or injury. Finally, in addition to meeting all the immediate requirements of service, it must possess qualities of durability which warrant a reasonable expectation of a long life of usefulness. The wise engineer no longer regards it as reasonable to depend upon mere bulk of its own material for the protection of a metal as readily impaired or destroyed by oxidation as iron or steel. The metal must have a coating which will be and remain impervious and indestructible. When all these conditions are met, we have as near an approach to the ideal tube as can be attained with the materials now available for their manufacture. Steel wed constructively, to the best advantage, meets these requirements most perfectly. Gold alone would do it better. If we search through the whole list of metals and alloys we find nothing available which so perfectly meets the requirements as a pipe material as steel. Mr. Hamilton Smith, Jr., in a paper on the expedients adopted on

Jan 1, 1891

By W. G. Lidman, H. J. Hamjian

' I HE fabrication of many materials from powders involves a sintering process. A mass of powder will sinter because of the excess free energy over the same mass in the densified state caused by the higher total surface area of the powder. An understanding of the kinetics and mechanism of sintering should assist in improving the properties of such materials. The present investigation conducted at the NACA Lewis laboratory deals with the sintering of chromium carbide. Dry sintering (sintering at a temperature below the melting point) was divided into two stages by Shaler:' the first stage, during which the particles preserve much of their original shape and the voids are interconnected, and the second stage, during which densification occurs and the pores are isolated. The mechanism of forming interfaces between particles, or welding together of particles, has been investigated by Kuczynski2 and may be described by any one or a combination of the following mechanisms: viscous flow, evaporation and condensation, volume diffusion, or surface diffusion. The mechanism by which pores are closed or eliminated (densification) during sintering, is of interest. Grain growth observed during sintering may be attributed to the variation in the surface energies of individual grains, causing some grains to grow at the expense of others. Grain boundary migration occurs presumably by a diffusion process, therefore the rate of grain growth would be expected to increase exponentially with increasing time and temperature. Thus, for practical sintering times of less than 1 hr, a certain minimum temperature may exist at which major structural and property changes will occur. Densification and kinetics of grain growth during sintering under pressure of chromium carbide were investigated to provide additional information which will aid in describing more accurately the sintering process and the mechanisms involved. This material was selected for this study because of the current interest in high strength, oxidation resistant refractory materials, such as carbides, which are sintered to produce solid, dense materials from powders. Sintering under pressure is a process where the heat and pressure are applied to the compact simultaneously, specimens for this work were prepared by sintering under pressure at different temperatures and for various time periods. Experimental Procedure Preparation of Specimens: Chemical analysis of the commercial chromium carbide used in this investigation was as follows: Cr 86.19 pct, C 12.14 pct, and Fe 0.2 pct. X-ray diffraction powder patterns gave characteristic diffraction lines of Cr3C2 crystal structure. Powder particle size was determined microscopically and the average initial particle size was 6 microns with 85 pct between 2 and 10 microns. Specimens sintered under pressure were formed in graphite dies3 heated by induction. Sintering temperatures were measured with an optical pyrometer by sighting into a 3/8-in. hole drilled 1 in. deep at the midsection of the graphite die. A load of approximately 1 ton per sq in. was applied to the powder. The die assembly was heated in 20 min to the highest temperature (2500°F') at which no increase in grain size could be observed, and less than 2.5 min were required to heat from this temperature to the maximum temperature (3000°F). Sintering temperatures and times for the specimens of this investigation are indicated in Table I. Analysis of Specimens: Specimens polished with diamond abrasives were etched to reveal the grain boundaries with a 1:1 mixture of 20 pct potassium hydroxide and 20 pct potassium ferricyanide heated to 160°F. Representative areas of each sample were photographed at 1000 diameters. The largest diameters of all well-defined grains were measured, but only the measurements of 15 of the largest grains were averaged in order to determine an index of grain size on the assumption that they were among the first to begin growth. Densities were determined from differential weighing of the samples in air and water. The reported density values are considered correct within ±0.01 g per milliliter. Results and Discussion Metal compacts have exhibited grain growth when sintered at temperatures about two-thirds of the absolute temperature of their melting point.' Grain growth also occurs during the sintering of chromium carbide and is illustrated by the micrographs shown in Fig. 1. These micrographs were prepared from specimens sintered for 90 min at temperatures ranging from 1371°C (2500°F) to 1648°C (3000°F). Average grain size and density measurements of specimens investigated are presented in Table I. The relationship between grain size and sintering tem-

Jan 1, 1954

By M. J. Hordon, M. A. Wright

ReCENT work has indicated that the substantial decrease in the rate of fatigue crack propagation for aluminum observed below a critical vacuum level can be attributed to the depletion of oxygen or water vapor from the vicinity of the fatigue crack opening.' At reduced gas pressures, generally below 10-2 Torr with fatigue strain amplitudes in the range *1 to 2 x 10-3 and cyclic loading rates of 25 to 50 cps, estimated rates of oxide or hydroxide monolayer adsorption on newly formed crack surfaces can fall behind the actual rate of crack extension. Changes in the critical pressure required for the transition in fatigue behavior with changes in temperature, strain amplitude, and cyclic frequency can be interpreted from variations in the adsorption and crack growth rates.'" Although the adsorption model generally appears to explain the enhanced fatigue resistance of reactive metals in vacuum, the specific adsorbing gas species and nature of the adsorption mechanism are uncertain. In addition to the direct dissociation and adsorption of O2 on the metal surfaces,3 the dissociation of H20 and subsequent adsorption of H ions have been advanced for aluminum alloys.4 The present note describes some measurements of the fatigue behavior of 1100 aluminum in reduced partial pressures of specific gases including O2, H2O, and H2 in order to provide additional experimental data. Cantilever-type specimens of 1100-H14 aluminum were fatigued in cyclic reverse bending at constant strain amplitude using a multispecimen vacuum apparatus and procedure described previously.' After initial vacuum evacuation to 1 x 10-7 Torr, the appropriate gas species was bled into the system through a calibrated leak valve. The input rate was adjusted to maintain the desired pressure level under continuous evacuation, thus minimizing possible changes in gas composition during testing. High-purity input gases including 99.9 pct O2, 99.999 pct H 2, and water vapor from triply distilled H 2 O were used to provide residual pressures. Trace amounts of contaminant species were limited by passing the Oz and H 2 input gases through liquid-nitrogen-cooled copper coils prior to entry to the test chamber. Care was taken to repeatedly flush the gas lines and valves before testing to minimize the effect of adsorbed contaminants. Residual gas pressures in the range 10-6 to 5 x x3 Torr were monitored by an NRC ionization gage corrected for each gas species. In the higher-pressure range, 5 x 1CT3 to 5 x 10' Torr, an NRC alphatron gage was used. In operation, eight simultaneous fatigue tests were conducted at a constant strain amplitude of *1.2 x 10 at cyclic bending rates of 25 and 50 cps to give an average fatigue life of 6.5x 105 cycles-to-fracture at standard atmosphere and 3.3 x 106 cycles in 1 x 10"7 Torr vacuum. Representative results for the effect of residual O2, H2O, and H2 contents on the fatigue life are shown in Fig. 1 for tests performed at 50 cps. It is apparent that the presence of either O2 or H2O gas in the system at partial pressures greater than 10"3 Torr was noticeably detrimental to the fatigue life. In contrast, the enhanced fatigue resistance typical of high-vacuum environments was retained with pure H 2 through the pressure range up to 1 Torr. For partial pressures of H2 gas above 1 Torr, the fracture life noticeably decreased. The critical Hz

Jan 1, 1969

By W. M. Courtis

In compliance with the suggestion in Mr. Emmons's paper on the Genesis of Certain Ore-Deposits (Trans. xv., 125), that facts should be accumulated for study and future compilation, I wish to put on record, before the data are lost, a section of the Animikie series of rocks and the vein-phenomena exposed by the explorations at the Duncan mine, Port Arthur, Thunder Bay, Lake Superior. This may serve as a supplement to my paper on this district (Trans. v., 473). I trust this information will not be without interest at. the present time. The recent discoveries of very rich silver-ores at Rabbit and Silver Mountains, on the same belt, have brought the district once more before the public; and a study of the facts here set forth may assist some fellow-engineer in the determination of the value of property offered for sale in this neighborhood. The vein at the Duncan mine was tested to a depth of over eight hundred feet by shaft and drifts, and to nearly a thousand feet with

Jan 1, 1887

By John Birkinbine

In a former paper* attention was directed to the various forms of pumping machines employed for permanent work in mining and metallurgical processes. The following is simply a collection of memoranda of work done of a temporary character, and is presented by way of comparison with other work of similar nature. In close proximity to the charcoal fnrnace at Pine Grove, Cumberland County, Pa., is a large deposit of superior hematite iron ore, which has been worked for a number of years, and from which many thousand tons of ore have been taken by open pit workings. In July, 1874, the furnace was blown out and operations at the bank suspended, the machinery for draining being removed except a plunger pump, 18 inches in diameter and 66 inches stroke, operated by a steam-engine by means of rods. The pit was allowed to fill with water, and no steps towards its reclamation were taken until November, 1877. At that time the pit was a pond of water at the base of the mountain, having an area of about four acres and a depth of seventy feet. As the pumps, rods, etc., had been submerged for over three years, and partially buried by the mud washed down from the banks, and as it was determined to change the location of the pump for future operations and drive it by water-power, a temporary pumping apparatus was determined upon for reclaiming the pit and keeping it drained until the permanent arrangements could be completed. By opening an old adit about 10 feet of the water was removed, and the area decreased to three acres. The inflow of springs was found to be 250 gallons per minute, and the amount of water contained in the pit was computed to be 45,000,000 gallons. As the inflow would undoubtedly increase while the water sank in the pit, provision was made for removing at least 60,000,000 gallons, at the rate of 1,500,000 to 2,000,000 gallons per day. The company determined to employ a Heald and Cisco centrifugal pump driven by an oscillatinig engine by means of a belt. Steam was supplied by four plain cylinder boilers, each 36 inches diameter

Jan 1, 1879

By H. A. Guess

Introduction. History and Production Statements. Southeast Missouri is the oldest of the large producing districts of the United States. The first recorded production from disseminated ores was in 1869, although for many years prior to that time lead had been milled from shallow pockets, and steady growth in production has been shown ever since, the greatest increases being during the past five years. The production by years for each of the operating companies from 1869 to 1907, inclusive, is given in Table I. In Table 11. is given the production by years from 1908 to 1912, inclusive, for the district as a whole, showing the tonnage of crude ore mined, yield in concentrates, average assay of concentrates; yield in metallic lead both per ton of crude ore and in total; also approximate value of the yearly production. It is interesting to note that the production for the 5-yr. period 1908 to 1912, inclusive, is practically equal to the total previous production, viz., the 39-yr. period 1869 to 1907, the summary being as follows:

Jan 1, 1915

By R. J. Wysor

MoRe than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same, furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100" F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently done some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C.,R. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based on the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations. Method of Conducting the Tests The location of the pyrometer fire ends is shown in Fig. I, a plan of Bethlehem Steel Co.'s "G" blast furnace, hot-blast stoves, and main. Bare fire ends were used at both positions "A" and "B," being inserted

Jan 1, 1916

By H. R. Barnhurst

It would be a difficult matter to trace from the beginning the very few improvements made in the burning of fuels prior to 1860. Donbtless the crossing of the sticks of wood in building a mood fire early appealed to our savage ancestry as a means of expediting its effectiveness for their crude culinary purposes. Stones and andirons came later in assisting the admission of air to the under part of the fuel bed, while beacons and cressets, utilized metal bars as supports for the same purpose. It is probable that Tuba1 Cain owed his success to the use of bellows making possible the use of mixed fuel and charge upon a hearth. With the development of working in cast iron, grate bars came in, and they are still with us doing duty in every household and almost every art where heat is a factor. Little was done beyond these crude methods prior to 1860. With the advancement of knowledge came the fuel-gas producer, a natural child of the retorts employed in supplying illuminating gas. It is only within the last 15 years that the conclusion became general that complicated systems for saving heat would not remedy deli-. ciencies in its primary development, and within that time there has been great advancement in the means of producing initially a fire of high effciency, so that to-day we are moving rapidly toward both high development and high absorption, with the resultant of high efficiencies. In studying the subject of the availability of pulverized coal as a fuel, it may occur to ask, why has this not come up earlier? This, question would be naturally prompted by recalling the fact that Thomas Crompton's English patents upon his methods were issued to him nearly 40 years ago. A conclusive answer to this, however, is that Crompton at that time had very crude facilities for making what was at best a very imperfect pulverization of the coal, arid the expense of preparation mas very great. He does not seem to have been aware of the advantage of a thorough drying of the coal in the

Jan 1, 1914

By John E. Hockett

The need for basic information about the relationship between resistance to dejormatim (flow stress), temperature, strain, and strain rate, for the solution of metal-fovming problems, is pointed out. Some early attempts to satisfy the need are mentioned. A brief description of a machine called a Cam Plastome-ter is given, including the processing of results of testing in the machine. Next, a program of testing aluminum in compression over a wide range of constant true-strain rates (0.1 to > 200 sec-1) and a modevately broad range of temperatures (223° to 673°K) is described. The results of this program are presented in the form of true-stress us true-strain cuvves. The data in these curves are presented in the form of relationships between true stress and true-strain rate in sermilogarithmic and log-log form, as functions of temperatures—for several true strains. Finally, true stress, for a given true strain, is displayed as a function of log true-strain rate and absolute temperature, i.e., a surface. SINCE the publication of Hill's book1 on plasticity theory, increasingly rapid advances have been made in analytical solutions to forming problems. Methods in common use are the slab method, the uniform deformation energy method, the limit analysis method, the slipline field method, and the semiexperimental method called "visioplasticity". These approaches, and examples of their use, are covered in detail by Johnson and Melloor2 and by Thornsen, Yang, and Kobayashi.3 unfortunately, practically all of the above work has had to rely upon a number of basic assumptions, e.g., homogeneous deformation and Coulomb (sliding) friction; and virtually no dependence of the mechanical behavior of the deforming metal, upon temperature, strain, and strain rate, has been included. It is with this dependency that this paper is concerned. Loizou and sims4 looked at the above relationship for lead using both a constant compression-speed Cam Plastometer and a constant true-strain-rate Cam Plastometer designed by Orowan.5 Alder and Phillips8 investigated the relationships for aluminum, copper, and steel in the same constant true-strain-rate Plastometer. cook7 tested twelve steels at temperatures ranging from 1170° to 1473°K in the same Plastometer over a range of true-strain rates of 1.5 to 100 sec-'. The writer tested commercially pure aluminum at room temperature and depleted uranium at temperatures from 573" to 873°K at strain rates from 10-3 to 1.0 sec-1 in a Cam Plastometer designed and built at Los Alamos Scientific Laboratory.8 During the past few years the Cam Plastometer at Los Alamos has been used for a number of relatively minor experiments on brass, mild steel, duralumin, Armco iron, and depleted uranium. In this time the machine has been continually modified and improved. It was decided to utilize fully the wide range of strain rates now available with the machine by testing a material about which some information was already in the literature. Prior work on commercially pure aluminum6 appeared to deserve confirmation and expansion. So it was decided to explore the resistance to compression of this material over the currently available range of constant true-strain rates and a convenient range of temperatures. This paper is a report of that exploration. I) EQUIPMENT AND PROCEDURE The principal item of equipment is, of course, the Cam Plastometer, the working part of which is shown in Fig. 1. In this figure, an aluminum specimen may be seen between two tungsten carbide platens, in position for a room-temperature test. Above the upper carbide platen is a load cell. Output from the load cell is amplified and applied to a galvanometer in a recording oscillograph. Auxiliary equipment includes the oscillograph, the control console, a counter, and a time-mark generator. The counter is first used in adjusting the time base. Then it registers the count, of sixty pips per revolution generated by the rotating cam, in each second. These pips and the time base are also applied to galvanometers in the oscillograph. Thus, load, time, and cam position are recorded simultaneously. Heating of a specimen prior to compression is done

Jan 1, 1968

By Daniel M. MacNeil, Carle R. Hayward, Raymond L. Presbrey

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By Daniel M. MacNeil, Raymond L. Presbrey, Carle R. Hayward

At the February, 1916, meeting of the Institute, a paper presented by Hayward and Raymond gave the results of a study on the effect of time in tempering medium-carbon steel, when the following conclusions were reached: It is not fair to consider the question settled when only three specimens were used for each treatment, but the results obtained indicate that for reheating quenched medium-carbon steel to temperatures below 500" it is only necessary to heat it through. Longer heating has little or no effect on the tensile strength, ductility, or hardness. At temperatures above 500°, increasing the time of treatment causes a slight falling off in hardness and tensile strength with a corresponding increase in ductility. In the discussion of the paper these conclusions were attacked and evidence was presented that seemed to throw doubt on their accuracy. The authors, however, showed that this evidence was based on high-carbon or alloy steels and no facts regarding medium-carbon steel were presented. During this study the heat treatment was carried out in a small electric resistance furnace. It held nine specimens, but when these were placed in the furnace the temperature was lowered to such an extent that 30 to 40 min. were required to reach the desired heat. The authors pointed to this as a weak point in the investigation and it seemed wise to supplement the research by work on similar steel but using a different method of heating. This has been done and the results are given in the present paper. The Rhode Island Tool Co. coöperated by furnishing the steel and turning the tensile specimens. The steel used in this investigation came in three bars 3/4 in. in diameter; analyses are as follows: Carbon. MaNGanese, Phosphorus, Sulfur Bar NUmber PeR Cent. Per Cent. Per Cent. Per Cent. 1 0.46 0.56 0.010 0.055 2 0.44 0.58 0.007 0.042 3 0.48 0.58 0.007 0.048

Jan 1, 1922

By Frederic H. Lahee

The purpose of this paper is to demonstrate the similarity of the oil-producing structures in the Mexial fault zone, and to show how the apparently very irregular well logs in these fields may be use? for the practical interpretation of subsurface conditions. The Mexia oil field, in Limestone County, Tex. (Fig. 1) is closely associated with a fault that trends about 30" east of north and has a displacement of between 200 and 400 ft., with downthrow on the west. Minor slips accompany this major fault, some being roughly parallel to the main break while others are transverse to it. These faults belong to the so-called Mexia fault zone, a belt of fracturing that has been traced in its characteristic features southward to near Kosse, 15 miles south of Groesbeck, in southern Limestone County, and northward at least as far as the Trinity River at the eastern border of Navarro County, and possibly as far north as Hunt and Hopkins counties.2 The Balcones fauil zone, from 30 to 40 miles west of the Mexia fault zone, differs from the latter in that its principal displacement is a downthrow on the east. In this respect, it is exactly the opposite of the Mexia displacement. Between these two zones of major faulting lies a great down-dropped block, or graben, which is broken by numerous minor faults. Oil Fields Associated with Mexia Fault Zone When speaking of oil fields associated with the Mexia fault zone, we refer only to those now producing from the Woodbine sand. In this category belong the Mexia, Currie, Old Richland or Seay-Cranfill, Powell, and New Richland fields, named in the order of their discovery (see Fig. 1). Subsequent development may prove that the gas found in the Boyd Oil Co.'s Connor well, north of Kerens, is coming from another pool in the same fault zone.

Jan 1, 1925

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.'-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225' apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By John M. Campbell, W. E. Portman

A series of correlating charts have been prepared to enable the field engineer to predict the amount of stock tank fluid produced by stabilization of first stage separator fluid. The charts shown are particularly convenient for estimating the relative effect of temperature and pressure in economic studies. Further work is planned to investigate the factors affecting stage separation' yo supplement this preliminary work. The direct correlation of separation variables is dictated as a convenience to eliminate the trial and error calculation necessary when using the standard flash vaporization equations. These are obtained by a material balance using the equilibrium vaporization ratio K, and have appeared in the following, or similar. form many times in the literature. where La = mols of any component n in the separator liquid Ko — equilibrium vaporization ratio for any component at separator pressure and temperature Fa = mols of any component n in the feed Vn = mols of any component n in the vapor V = total mols of separator vapor These equations may of course be effectively and accurately solved by use of digital and analog computers. However, these are not usually readily available in field offices and the need often arises for fast results during routine operational problems. Consequently, many methods have been devised in an attempt to simplify the basic calculation.2-14 The methods proposed are generally satisfactory, but do not eliminate trial and error methods and the necessity of subsequent calculations to obtain the answer in volume terms. The purpose of this work. therefore, was to develop accurate charts that would give the result directly in gallons. When using stage separation the recoveries would be lower than those shown, for stabilization usually gives about 95 + per cent recovery on the potential stock tank components in the separator liquid. The recoveries are shown in terms of a 14 psi Reid Vapor Pressure product which has a true vapor pressure of 14.7 psia at 98°F. Consequently, this product represents a stable stock tank liquid under normal storage conditions. To estimate natural gasoline re- coveries by stabilization the volume shown may be multiplied by 1.20 for 18 Ib RVP natural gasoline and 1.36 for 26 lb RVP natural gasoline. PROCEDURE The five analyses shown in Table 1 were chosen since they were representative of wellstream compositions often found and had almost the same propanes plus liquid content, expressed in gallons per 1,000 std. cu ft of wellstream. The distribution of the components though is widely variant. A temperature range of 0-100°F. and a pressure range of 200 to 1,250 psia was chosen inasmuch as most separations fall within these limits The K values used were modified values of those originally published by Katz and Hachmuth.' In the range chosen these have generally given good results when predicting fluid recoveries. The choice was somewhat arbitrary, for the authors' personal experience has shown that

Jan 1, 1957