Search Documents

By G. Sachs, E. J. Ripling, S. I. Liu, J. J. Lynch

It is a generally recognized fact that by repeated straining the fracture stress of any metal is reduced to a fraction of its value for static loading. The value of this fatigue strength depends upon numerous factors, such as the states of strain and stress, the limits of straining, and the number of repeated loadings or cycles The large volume of previous investigations on fatigue is concerned entirely with large numbers of cycles, say exceeding 10,000 and up to 500,000,000. However, the changes in fracture stress and fracture strain occurring after a small number of repeated loadings have attracted little attention. Apparently the only investigations of this type are those byLudwik4.5 who subjected steel, copper, and aluminum wire to repeated torsion. In each test the torque was varied between identical values in the two directions of twisting. Depending upon the magnitude of the moment, fracturing occurred after a number of cycles, up to 10,000. The results of Ludwik's tests will be discussed later Such torsion does not readily yield actual stress and strain values. Therefore a pre- liminary study was made of the effects of repeated direct stresses, that is, tension and compression stresses. Because such tests are considerably more tedious than torsion tests, only high stresses were used in the preliminary work, yielding definite changes in metal properties after a few cycles. It was found in these tests that strains could be controlled more readily than stresses in the investigated range of high stresses. This paper, consequently, deals with the effects of strains of equal magnitude but different signs. The metal was first prestrained in static tension by a certain amount then subjected to compression to yield the same amount of strain after unloading. This loading cycle was repeated up to a maximum of seven times. After various cycles, the stress-strain curves in tension were determined, up to fracturing. As material for these tests, the aluniinum alloy 24ST was selected because it exhibits a comparatively small amount of necking in the tension rest This alloy permitted, therefore rather accurate cont.rol at the high strains necessary to produce fatigue failures at less than seven cycles. The results of this invest~gation appear sufliciently interesting to extend the method of attack in various directions It is intended to study (11 the effects of cycles up to a tew thousands and (2) the effects of strains of different magnitude in tension and compression respectively 'The latter variable also includes a. a special case the effects of compressive strains.

Jan 1, 1949

By George B. Clark

The "Munroe effect" of shaped explosive charges was discovered by Charles E. Munroe more than 50 years ago (in 1888), but it was not until World War II that it was put to any practical use. Both Allied and Axis armies used the principle effectively in bazooka projectiles, artillery projectiles and in fixed shaped charges. The first two were used primarily to combat tanks and other armor and the latter to assault pillboxes and other fixed concrete emplacements. Many engineers and others who saw the military application of the jet effect of shaped charges believed application would be possible in many industrial fields where blasting is used, such as mining and quarrying. Some work has already been done on the problem of making shaped charges applicable to mining operations. Experimentation conducted at the National Tunnel and Mines1 was directed primarily along the lines of use of shaped charges for secondary blasting in connection with long-hole stoping methods. Experimentation initiated earlier and conducted by the author2 at the University of Utah on a more scientific basis was directed at revealing the basic principles of the functioning of shaped charges, as well as the feasibility of using them in mining operations after the principles of their operation had been clearly defined. It was found that: (I) a given design of charge required an optimum standoff to make it most effective, either in penetrating solid rock or steel (see Fig 3); (2) for a given design of charge there exists an optimum ratio of charge diameter to charge height above which the increase in effectiveness of the charge decreases rapidly (see Figs 4 and 5); (3) partial confinenlent has the effect of making charge performance much more consistent; (4) the higher power and higher velocity explosives tested are much more effective than relatively low-strength explosives; and (5) shaped charges may be adaptable to mining operations in secondary breakage and drilling blasting holes. Fig I is a diagrammatic sketch of the action of a shaped charge for two types of cavities, while Fig 2 shows the approximate manner in which the jets are believed to be formed when an explosive wave encounters the cavity, approaching it from the top. The experimentation already completed has laid the foundation for further research in the study of shaped charges. Standoff effects, effect of the strength of explosives and other features have been fairly well established. Such elements in the design of shaped charges as (I) geometry of cavity liners, (2) relative horizontal dimensions of explosive column, (3) effect of various metals and alloys in cavity liners, (4) percentage studies of jet energies, and

Jan 1, 1949

By Fred P. Peters

At first glance this paper may seem unique among those comprising this symposium on designing for powder metallurgy, since it is evidently concerned with everything but Powder metallurgy. This paradox mill be at once resolved, however, when the real Purpose of the symposium meeting is understood—to present factually and objectively the things that can and cannot he done with powder-metallurgy methods, and especially to set forth with brutal frankness the limitations of Powder metallurgy, so that costly over-enthusiasm and misapplication may be prevented. Since much of powder metallurgy's future development (and many of its present disappointments) has been in competition with other and long-established methods of fabricating parts, it is easy to see that its true competitive possibilities in any given case cannot be accurately appraised without rudimentary knowledge of what the competition can do. This paper, therefore, presents a few reminders of things you all know—a background to be kept in mind as you examine the data on each of their specialties given by the authors of the papers that follow. From the standpoint of the design engineer powder metallurgy is often in Competition with one or more of the following: sand casting, die casting, permanent-mold casting, precision investment casting, ma- chined bar stock, screw-machine parts, cold-heading, drop-forging, and stamping and drawing. We will here briefly discuss each of these individually, and set forth so, rough (and therefore dangerous) generalizations about its competitive position, especially with respect to powder metallurgy. Sand Casting Sand-casting of small parts is sometimes an inexpensive method of manufacture, for its raw-material costs (i,e., for gray iron) are the lowest of the various methods and it involves the use of no tools and dies of jewelry quality. its design flexibility— that is, the ability to make complicated, cored and undercut parts in one piece—is about the highest of the competing processes and in this respect it can do many things that are impossible by powder metallurgy. For small castings its production rates may be higher, by using multi-impression molds, than can be achieved with parts of the same size by powder metallurgy. But its labor charges for melting, pouring, patternmaking and molding are comparatively high and the waste it entails in gates and risers is always considerable. Tolerances of sand castings are wide (+1/6 to 1/32 in- per in.) and where precision approaching that of powder metallurgy is required sand castings must be machined to final size, thus increasing their cost. Steel sand castings are more expensive and less precise than iron, and nonferrous the most costly of all.

Jan 1, 1945

By Jerome F. Kuzmick

Condusions. From the work on aluminum powder, the following general con clusions can bc drawn: I. The physical properties of aluminum compacts, such as density. strength and ductility, increase with increasing pressure, up to the practicable pressure limits. 2. Good properties ill aluminum con pacts can be secured only by the use of high pressures, because it is neccssary to rupture the refractory oxide film on aluminum powder. 3. Considerable softening of the specimens occurs upon sintering. regardlers of the pressure used. General Conclusions 1. For relatively short-time sintering. molding pressure is a very important factor in the final physical properties of the sintered specimens. 2. The effect of pressure. is difierent for each metal, so that few general rules can be drawn that would apply to all metals. 3. In many cases, fur a particular metal powder and sintering temperature there is a critical pressure at which the best physical properties can be obtained. 4. The principles of cold work and in nealing and their effect on grain structure applied to massive metal also holds true for sintered metals. 5. Particle size, at least for electrolytic iron powder, does not have a. great effect on ultimate grain six. DISCUSSION [E. E, Schumacher presiding V.. V. Crane. *—I was particularly impressed with Dr. Kuzmick's work on tin IF not the illustration, particularly the Second one. a very good illustraition of hot preessing. in that

Jan 1, 1945

By W. Rostoker, S. A. Spachner

STUDIES of precipitation phenomena by use of X-ray diffraction effects have shown that atoms of the precipitating phase initially form lattices of limited periodicity in two or three dimensions.1, 2 Such diffraction effects are usually plotted in reciprocal space to facilitate identification. Atomic chains, or gratings possessing unlimited periodicity in only one dimension, cause uniform intensity planes in reciprocal space. Platelets, or gratings possessing unlimited periodicity in two dimensions, cause uniform intensity rods in reciprocal space. Such studies have been accomplished by use of white radiation (Laue technique) or characteristic or monochromatic radiation used with rotating single crystal or Weissenberg cameras. Each one of these techniques have associated drawbacks. If the Lque or rotating single-crystal technique is used, the results which are obtained may be ambiguous.3 Diffraction photograms made with a WeisSenberg camera do provide a direct but distorted representation of the variation of diffracted

Jan 1, 1960

Jan 1, 1903

By M. B. Ramachandra Roa

This paper records the results of the earth resistivity surveys made in the Godavari River in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented. Introduction The Government of Madras has under consideration the Ramapadasagar project which is estimated to cost some Rs.660,-000,000 (about two hundred million dollars). The most essential feature of this project is the construction of a high dam across the Godavari near Polavaram for impounding the waters of this great river of South India, whose maximum discharge is 2 million cu secs in flood time. It is estimated that when the proposed reservoir is constructed, about one million tons of rice could be produced annually under irrigation. To those who have had any acquaintance at all with the recent distressing famine conditions which India has passed through and is still undergoing, the Lounteous effects which this project will bring about to the country in the future, are obvious. In the region of the proposed reservoir, the river flows for several miles through a hilly tract, hemmed in between flanks of hard, solid rock; but the river bed is mostly sandy. A few bore holes put down in this sandy bed touched rock at a depth of 180 to 200 ft. The river bed is about jo ft above the mean sea level (m.s.l.) and the bedrock was found at —125 to —160 ft m.s.l. The crest of the dam is proposed at +162 ft m.s.l. The proposed dam mould therefore be about 120 to 130 ft above the river bed, and the foundations would have to reach down nearly zoo ft below the bed at the deepest part. A number of alternative sites were proposed for investigation, and it became necessary to quickly ascertain the bedrock topography at these sites. Dr. M. S. Krishnan,* who was consulted in the matter, furnished a detailed account of the geological features of the region and suggested a geophysical investigation which the writer carried out from February to April 1944, employing solely the electrical resistivity methods. The total length of the survey lines for the electrical measurements amounted to 62,600 ft and the number of resistivity determinations was about 2500. Altogether nine alignments for the dam were inten-

Jan 1, 1949

By G. Sachs, Jr. Brown W. F., Ebert L. J.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By Ebert L. J., G. Sachs, Jr. Brown W. F.

It is a generally recognized fact that a steel quenched from the austenitic range and tempered to yield a structure composed of tempered martensite becomes increasingly more ductile with increasing tempering temperature. However, the conventional tensile test fails to yield any value that is sensitive to differences in behavior on tempering among the various low-alloy steels or among different heats of a particular steel. The notched impact bending test, on the other hand, has been recognized for a considerable length of time as capable of revealing differences in impact properties among various steels tempered to 'the same strength level (i.e., the same tensile strength in a conventional tensile test). However, this test is very complex and its significance has not been clarified up to the present time. Of its three characteristic features—the high speed, the notch, and the bending—the notch has been found by Davidenkov2 to be the most potent embrittling factor. Recent investigations on low-alloy steels have shown static notch-bar tensile tests to be more lucid and to evaluate the metal properties in much the same manner as impact tests. In an attempt to analyze the fundamental nature of this test, it was found possible to separate the effects of the two basic characteristics of the stress pattern introduced by the presence of a circumferential notch, the stress state and the high initial stress concentration at the notch bottom. The major conclusions drawn from these previous investigations were as follows: I. The magnitude of the triaxiality at fracture depends primarily on the initial notch depth. Its effect is a great reduction in the average ductility (contraction in area at fracture in the notched section) as compared with that observed in uniaxial tension. This triaxial stress state occurs at a point in the interior of the notch specimen. It determines the notch ductility if the notch is mild and/or the metal possesses a considerable ductility. On the contrary, brittle specimens probably fracture on the metal surface (at the notch bottom) at which point biaxial stress state is present. This biaxiality also considerably reduces the ductility of the metal. For small notch ductilities the notch strength and the notch ductility become very sensitive to embrittling factors. This is contrary to the behavior. of the ductility values derived from a conventional tensile test, which are comparatively insensitive.

Jan 1, 1947

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By L. F. Mondolfo

R301 is a clad aluminum alloy, composed of a core of a duralumin-type alloy clad with a magnesium silicide alloy. It differs from other well-known clad alloys in that the cladding and the core respond to the same heat-treatments. and therefore the cladding contributes appreciably to the mechanical properties of the material. In Table I are reported the compositions of the core and cladding alloy for the material used for the experiments. Table i.—Chemical composition of R~OI Used for the Experiments Element Core Cladding Cu........................ . 0.01 Fe......................... . 0.42 Si......................... 0. 0.71 Mg........................ . 0.99 Mn ........................ . 0.54 In clad aluminum alloys where the core contains copper and the cladding does not, at elevated temperatures the copper tends to diffuse from the core through the cladding. This fact is well known and many investigations have been conducted to determine the features of this diffusion. Most of those investigations cover materials clad with pure aluminum; the present investigation covers a material clad with an alloy. Since the cladding thickness on R~OI varies with the gauge, as shown in Table 2, several gauges were investigated. Material and Procedure he material used was sheet of the following gauges: o.o2~, 0.040, 0.064, 0.102, 0.170 Cut in pieces approximately 3 by 5 in., it was in the cold-rolled state and was soaked for increasing times at the following temperatures: glo°F., 940°F., 970°F. A Lindberg cyclone furnace was used for the experiments. The procedure was as follows: The furnace was started empty with controlling pyrometer set at the determined temperature. After the furnace had reached that temperature, it was run for some 20 to 30 min. empty, in order to allow the temperature inside to become stabilized. Then the first samples were introduced. A load thermocouple, with recording pyrometer, was connected with the sample of the heaviest gauge. About 10 min. was required for the material to reach temperature and the soaking time was counted from that point. After zoo min. soaking, the second group of samples was introduced without stopping the furnace. After 200 min. more, the third group of samples was introduced, and so on, until the last sample had been introduced. Every time the furnace was opened and new samples were added, a drop of temperature was registered by the thermocouple connected with the material

Jan 1, 1946

By Horace F. Silliman, Curtis L. Wilson, Eugene C. Little

The change in electrical resistance and Rockwell hardness (16-100-B) of copper alloys containing Ni2Si and Co2Si was determined by annealing the quenched solid solutions at various temperatures for various lengths of time. The rate of precipitation of Nisi, as measured by the rate of decrease of electrical resistance and increase of hardness, increased with annealing temperature up to a certain point, depending on the percentage of Ni2Si present. At these temperatures discontinuities in the rate: change occurred. Similar discontinuities in the Co2Si alloys were no The solubility of Co2Si in copper was found to be 5 per cent at 970" DISCUSSION (Robert F. Mehl presiding) R. I?. Mehl, Pittsburgh, Pa. (written discussion).—The electrical conductivity and hardness curves reported in this paper are interesting, particularly because many of the anomalies of the precipitation processes are evident from such curves. The title of the paper, however, is deceptive, for it implies that measurements of electrical conductivity and hardness are suitable to determine the rate of precipitation. Neither of these methods is suitable for a quantitative measurement of rates of reaction or of precipitation in the solid state. Electrical conductivity in some alloys shows an anomalous increase during the first stages of aging at low temperatures; it is notably sensitive to strain and to state of subdivision. I have plotted the conductivity curve representing the decomposition of the phase at 555" C. in the copper-aluminum system, given in the paper by Smith and Lindlief (Fig. 47, p. 93) as a rate of reaction curve, and compared it with the curve determined by area evaluation (Fig. 7); these two curves are not coincident. Hardness is likewise very uncertain, for it is so much dependent upon particle size. Of the various methods proposed for the study of rates of reaction and precipitation, the evaluation of volume of reaction product from the respective area of matrix and reaction product on the photomicrograph is the most trustworthy; suffering, perhaps, only from low sensitivity during the early stages. This method, used originally by Davenport and Bain and now by Smith and Lindlief, is suitable for

Jan 1, 1933

By Frank C. Canney

The word "other" in paragraph 4, line 11, column 1, page 205, should read "over;" the correct version of reason 2, this paragraph, is: 'L. . . 2) to evaluate the usefulness of certain geo-chemical techniques, V. C. Kennedy and S. W. Hobbs of the USGS had already studied the distribution of copper, lead, and zinc in the soils (both in background areas and over veins) and in the water and plants, providing a criterion for measuring the magnitude and effect of soil contamination; ...9 On page 206, in the top left hand corner of Fig. 1 (in the area bounded by 47°35' and 116°10), the reference to Fig. 3 is incorrect. The area of Pine Creek, South Fork Coeur d'Alene River, and portion of Big Creek (the area which includes, from left to right, Kingston, Pinehurst, Smelterville, and Kellogg) should be identified as that of Fig. 2A. The headings for columns 1, 3, and 4, Tables I and 11, page 209, column 2, were reversed when the paper was printed. The corrected tables are:

Jan 1, 1961

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940

By W. L. Dennen, W. W. Wirth

Research looking toward the reduction of the cost of roof support by substitution of longer-life materials for wooden timber is fully justified by the fact that roof support is an important element of all production costs. Permanent or semipermanent roof support will reduce the expense of timber-maintenance crews during steady operations, but even more markedly during idle periods. The management, therefore, is faced with the important problem of timber renewals, which in times of regular operation are frequently obscured by more urgent problems of production. Increased use of timber in the Anthracite Region of Pennsylvania is caused mainly by increased percentage of coal obtained from robbing areas, which requires more timber for safety than development work, and maintenance of long haulageways through crushed ground despite the fact that less coal is transported over them. The timber reserve in the immediate vicinity of the mines has been depleted to such an extent that it is necessary to secure 70 per cent of the timber requirements from distant sources. Originally, mine timbering in this region was done by largely utilizing round props or legs with round collars. The whole cross section of the tree from which timber was cut was utilized by forming the joints between the legs and the collars with saw and adze, using plank or round saplings for lagging behind the legs and over the collars to prevent material falling between them. The Mine Inspectors' report of 1898 records an important digression from the use of round timber, when two tunnels at the Babylon colliery, near Pittston, Pa., were timbered with 12 by 12-in. square timber sets with mud sills, through quicksand for distances of 425 and 160 ft., respectively. The timbers were lagged with 3-in. plank to control sand. An early step toward the permanent type of roof support was the installation of "brick pillars or perfect arched brick rooms" instead of

Jan 1, 1940

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970