Search Documents

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By M. Muskat, M. O. Taylor

Theoretical calculations have been made on the performance to be expected of gas-drive reservoirs for various characteristics of the oil and gas and the producing rock. Such performante has been expressed graphically as curves for the reservoir pressure and gas-oil ratios of the production as functions of the cumulative oil recovery. The latter has been expressed in terms of percentage of pore space of the reservoir rock. Such curves automatically give values for the ultimate physical recovery, if the latter is interpreted as the recovery obtained when the reservoir pressure has declined to atmospheric, or to any other pressure chosen as defining the state of practical complete depletion. Calculations of these pressure and gas-oil ratio histories have been made for conditions in which the oil viscosity, the gas solubility and shrinkage, the size of an overlying gas cap, if present, the permeability-saturation characteristics of the rock, and the amount of connate water, have been individually varied, The results serve to show the extent to which the ultimate recoveries are sensitive to the important physical parameters characterizing the oil reservoir. As is to be expected, the ultimate recoveries are found to decrease with increasing oil viscosity. Because of the predominant effect of the oil shrinkage associated with the liberation of the gas in solution, the ultimate recovery will decrease with increasing gas solubility. Increasing gas-cap volumes lead to higher recoveries, although the contribution made by the gas-cap gas is small as compared with the oil expulsion by the equivalent amount of solution gas. As a whole, the oil recovery when expressed in percentage of the pore space is not very sensitive to the details of the permeability-saturation relationship. However, if the rocks possess an equilibrium free-gas saturation, the rise in gas-oil ratio will be retarded, and the 'ultimate recovery somewhat increased' The oil shrinkage associated with the liberation of the dissolved gas also leads to the result that as long as the connate water is immobile and the permeability ratio curve for the rock is a function only of the total liquid saturation, the stock-tank oil recovery will be less for a sand containing no connate water than for One with an Original water content as high as 3' per cent. The space voidage in the former case will be somewhat greater, but the effect of oil shrinkage will lead to smaller values for the equivalent stock-tank recovery. These calculations also give data showing how the productivity indexes for the producing wells will vary during the reservoir history. Because of decreasing Permeability to the oil and increasing oil viscosity, the productivity index will fall continuously as Production proceeds, and may finally reach values as low as 10 per cent of the initial productivity index. Introduction In a previous paper1 was developed the basic theory for the prediction of the production histories of gas-drive reservoirs. The data required for the application of this theory included the characteristics of the petroleum fluids, such as the viscosity of the Oil and gas phases, the solubility of the gas in the oil, and the oil shrinkage— all expressed as functions of the reservoir pressure—and the permeability-saturation characteristics of the producing rock, as

Jan 1, 1946

By M. Muskat, M. O. Taylor

Theoretical calculations have been made on the performance to be expected of gas-drive reservoirs for various characteristics of the oil and gas and the producing rock. Such performante has been expressed graphically as curves for the reservoir pressure and gas-oil ratios of the production as functions of the cumulative oil recovery. The latter has been expressed in terms of percentage of pore space of the reservoir rock. Such curves automatically give values for the ultimate physical recovery, if the latter is interpreted as the recovery obtained when the reservoir pressure has declined to atmospheric, or to any other pressure chosen as defining the state of practical complete depletion. Calculations of these pressure and gas-oil ratio histories have been made for conditions in which the oil viscosity, the gas solubility and shrinkage, the size of an overlying gas cap, if present, the permeability-saturation characteristics of the rock, and the amount of connate water, have been individually varied, The results serve to show the extent to which the ultimate recoveries are sensitive to the important physical parameters characterizing the oil reservoir. As is to be expected, the ultimate recoveries are found to decrease with increasing oil viscosity. Because of the predominant effect of the oil shrinkage associated with the liberation of the gas in solution, the ultimate recovery will decrease with increasing gas solubility. Increasing gas-cap volumes lead to higher recoveries, although the contribution made by the gas-cap gas is small as compared with the oil expulsion by the equivalent amount of solution gas. As a whole, the oil recovery when expressed in percentage of the pore space is not very sensitive to the details of the permeability-saturation relationship. However, if the rocks possess an equilibrium free-gas saturation, the rise in gas-oil ratio will be retarded, and the 'ultimate recovery somewhat increased' The oil shrinkage associated with the liberation of the dissolved gas also leads to the result that as long as the connate water is immobile and the permeability ratio curve for the rock is a function only of the total liquid saturation, the stock-tank oil recovery will be less for a sand containing no connate water than for One with an Original water content as high as 3' per cent. The space voidage in the former case will be somewhat greater, but the effect of oil shrinkage will lead to smaller values for the equivalent stock-tank recovery. These calculations also give data showing how the productivity indexes for the producing wells will vary during the reservoir history. Because of decreasing Permeability to the oil and increasing oil viscosity, the productivity index will fall continuously as Production proceeds, and may finally reach values as low as 10 per cent of the initial productivity index. Introduction In a previous paper1 was developed the basic theory for the prediction of the production histories of gas-drive reservoirs. The data required for the application of this theory included the characteristics of the petroleum fluids, such as the viscosity of the Oil and gas phases, the solubility of the gas in the oil, and the oil shrinkage— all expressed as functions of the reservoir pressure—and the permeability-saturation characteristics of the producing rock, as

Jan 1, 1946

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By W. H. Patnode

The effect of suspended solids on the resistivity of slurries is discussed and the relationship between drilling mud resistivity and mud filtrate investigated. It is concluded that it is erroneous to substitute mud resistivity for mud filtrate resistivity in electric log calculations. A recommendation is made that both the bud resistivity and the mud filtrate resistivity be determined when electric logs are run. INTRODUCTION The electric log is influenced not only by the resistvity of the drilling mud in the borehole at the time of logging but also by the resistivity of the drilling mud filtrate. Sherborne and Newtoni investigated the relationship of mud resistivity to mud filtrate resistivity and concluded that, "The resistivity of the mud in most cases closely approximates that of its filtrate," and "In fact, with the exception of Aquagel and its filtrate, the figures for any particular mud and filtrate are almost identical." Present practice is to determine only the drilling mud resistivity and apply this same value to calculations involving the mud filtrate. The purpose of this study is to reexamine the factors governing the relationship between mud resistivity and mud filtrate resistivity. EFFECT OF BOREHO1.E FLUID ON THE ELECTRIC LOG Resistivity Log The resistivity log may be modified by the resistivity of the borehole fluid in two different ways: (1) The apparent resistivity of a for-formation may be different from the true resistivity of the formation because of the flow of some current through the drilling mud in the borehole. Therefore the resistivity of the mud is an important factor. (2) The apparent resistivity may differ from the true resistivity, if a formation is invaded by mud filtrate, because of displacement by the mud filtrate of some of the interstitial fluid in the formation. In this case the resistivity of the mud filtrate rather than the resistivity of the mud is the important factor. Self Potential Log The self potential arises, in part, from electrochemical effects resulting from the interaction of connate waters in porous formations and the fluid in the borehole. Expressed in simple form, E = Klog-p where E is the electrochemical self potential, K is a derived constant, pl is the resistivity of the borehole fluid, and p2 the resistivity of the water in the formation. A theory of the electrochemical component of the self potential in boreholes has been recently set forth by Wyllie.3 In the above equation resistivities have been substituted for activities of the ions in the fluids.' It is therefore apparent that the resistivity of the mud filtrate is more nearly representative of the activities of the ions than is the resistivity of the mud. However, it is possible that in some instances the ionic activities of cations from certain clays may contribute to the total cationic activity of the drilling fluid to such an extent that the mud resistivity is more nearly representative of the activities than the filtrate resistivity. This is particularly the case when the resistivity of the mud is less than the resistivity of the mud filtrate. In addition the apparent self potential may be influenced by the resistivity of the drilling mud because of current flow through the borehole. RESISTIVITY OF SLURRIES Aqueous drilling muds are slurries containing fine-grained solid particles. The solid constituents consist mainly of added clays and weighting materials in addition to solids contributed by the drilled formations. The filtrate is primarily water in which quantities of salts or other chemicals are dissolved. The resistivity of the fiiltrate is a function of the type and quantity of dissolved material whereas the resistivity of the mud is a function of the combined resistivities of the filtrate and the resistivities of the suspended solids. Experiments have been carried out to determine the relationship between the resistivity of solutions and the quantity and type of solid matter insus-pension. Solid materials of high resistivity, as well as solid materials of relatively low resistivity, have been used. The data obtained make possible the evaluation of the probable effect of suspended solids on the resistivity of drilling mud. Procedure Resistivities were determined by means of a conventional conductivity cell with platinized-platinum electrodes. Total resistance between the electrodes was measured by Kohlrausch's alternating current bridge method using a General Radio Company Type 650-A impedance bridge with telephone. The cell was standardized with potassium chloride solutions of known normalities in order to calibrate the cell so that measured resistances of slurries could be converted to resistivities. Resistivities were determined for mixtures of potassium chloride solution and solid materials by placing a measured quantity of solution in the cell and adding weighed quantities of solid materials in small increments to the solution. The net change in resistance on addition of solid materials was measured. Even distribution of the solid particles was maintained within the cell by a motor-driven glass propeller before measurements were made. Slurries Containing High-Resistivity Solids Powdered silica sand having a maximum diameter of about 60 microns and precipitated chalk of commercial grade were used to make the slurries whose resistivities were measured. Both of these substances have high resistivities, are virtually insoluble, and effectively do not carry current in a slurry. The resistivities of slurries composed of potassium chloride solution and these two solid materials are given in Table 1. The ratio of the resistivity of the solution to the resistivity of the slurries was computed and was found to follow the relationship established by Archie

Jan 1, 1949

By W. H. Patnode

The effect of suspended solids on the resistivity of slurries is discussed and the relationship between drilling mud resistivity and mud filtrate investigated. It is concluded that it is erroneous to substitute mud resistivity for mud filtrate resistivity in electric log calculations. A recommendation is made that both the bud resistivity and the mud filtrate resistivity be determined when electric logs are run. INTRODUCTION The electric log is influenced not only by the resistvity of the drilling mud in the borehole at the time of logging but also by the resistivity of the drilling mud filtrate. Sherborne and Newtoni investigated the relationship of mud resistivity to mud filtrate resistivity and concluded that, "The resistivity of the mud in most cases closely approximates that of its filtrate," and "In fact, with the exception of Aquagel and its filtrate, the figures for any particular mud and filtrate are almost identical." Present practice is to determine only the drilling mud resistivity and apply this same value to calculations involving the mud filtrate. The purpose of this study is to reexamine the factors governing the relationship between mud resistivity and mud filtrate resistivity. EFFECT OF BOREHO1.E FLUID ON THE ELECTRIC LOG Resistivity Log The resistivity log may be modified by the resistivity of the borehole fluid in two different ways: (1) The apparent resistivity of a for-formation may be different from the true resistivity of the formation because of the flow of some current through the drilling mud in the borehole. Therefore the resistivity of the mud is an important factor. (2) The apparent resistivity may differ from the true resistivity, if a formation is invaded by mud filtrate, because of displacement by the mud filtrate of some of the interstitial fluid in the formation. In this case the resistivity of the mud filtrate rather than the resistivity of the mud is the important factor. Self Potential Log The self potential arises, in part, from electrochemical effects resulting from the interaction of connate waters in porous formations and the fluid in the borehole. Expressed in simple form, E = Klog-p where E is the electrochemical self potential, K is a derived constant, pl is the resistivity of the borehole fluid, and p2 the resistivity of the water in the formation. A theory of the electrochemical component of the self potential in boreholes has been recently set forth by Wyllie.3 In the above equation resistivities have been substituted for activities of the ions in the fluids.' It is therefore apparent that the resistivity of the mud filtrate is more nearly representative of the activities of the ions than is the resistivity of the mud. However, it is possible that in some instances the ionic activities of cations from certain clays may contribute to the total cationic activity of the drilling fluid to such an extent that the mud resistivity is more nearly representative of the activities than the filtrate resistivity. This is particularly the case when the resistivity of the mud is less than the resistivity of the mud filtrate. In addition the apparent self potential may be influenced by the resistivity of the drilling mud because of current flow through the borehole. RESISTIVITY OF SLURRIES Aqueous drilling muds are slurries containing fine-grained solid particles. The solid constituents consist mainly of added clays and weighting materials in addition to solids contributed by the drilled formations. The filtrate is primarily water in which quantities of salts or other chemicals are dissolved. The resistivity of the fiiltrate is a function of the type and quantity of dissolved material whereas the resistivity of the mud is a function of the combined resistivities of the filtrate and the resistivities of the suspended solids. Experiments have been carried out to determine the relationship between the resistivity of solutions and the quantity and type of solid matter insus-pension. Solid materials of high resistivity, as well as solid materials of relatively low resistivity, have been used. The data obtained make possible the evaluation of the probable effect of suspended solids on the resistivity of drilling mud. Procedure Resistivities were determined by means of a conventional conductivity cell with platinized-platinum electrodes. Total resistance between the electrodes was measured by Kohlrausch's alternating current bridge method using a General Radio Company Type 650-A impedance bridge with telephone. The cell was standardized with potassium chloride solutions of known normalities in order to calibrate the cell so that measured resistances of slurries could be converted to resistivities. Resistivities were determined for mixtures of potassium chloride solution and solid materials by placing a measured quantity of solution in the cell and adding weighed quantities of solid materials in small increments to the solution. The net change in resistance on addition of solid materials was measured. Even distribution of the solid particles was maintained within the cell by a motor-driven glass propeller before measurements were made. Slurries Containing High-Resistivity Solids Powdered silica sand having a maximum diameter of about 60 microns and precipitated chalk of commercial grade were used to make the slurries whose resistivities were measured. Both of these substances have high resistivities, are virtually insoluble, and effectively do not carry current in a slurry. The resistivities of slurries composed of potassium chloride solution and these two solid materials are given in Table 1. The ratio of the resistivity of the solution to the resistivity of the slurries was computed and was found to follow the relationship established by Archie

Jan 1, 1949

By Herbert F. Miller

For a long time I have believed that the gas- and brick-costs of open-hearth furnaces using prodncer-gas could be greatly decreased by a change in the design of the port, which would materially reduce the first-cost of the furnace, the rebuilding-cost, and the repair-cost. The defects of the present type of such furnaces, which has clone duty for so many years, may be studied in Fig. 1, in which A A are the two air-uptakes, B is the gas-uptake, and C the end of the gas-port. In the present type of furnace, C is practically 011 the edge of the bath and therefore combustion begins to take place at that point, but has no effect until the gas passes from 5 to 10 ft. into the hearth. As the furnace grows older, C moves back by reason of the burning or falling down of the arch. The furnace reaches its highest efficiency when C has moved a certain distance, but is still near enough to the bath for the overhead layer of air to hold the gas down on the bath, and far enough back to permit combustion to take place at some distance from the bath. This latter fact means that the temperature is sufficient to melt steel at the edge of the port. From this time on, the furnace decreases in efficiency. What is the reason ? As C moves further hack, the gas is released from the gas-port at a point where there is little or no overhead layer of air. The result is that the gas floats along the roof, with the air mostly underneath it. Why the air does not stay over the gas is readily seen in Fig. 1. The lines of draft naturally run parallel to the length of the furnace. The air-uptakes being on the sides and the gas-port in the middle, most of the air will naturally be drawn along the sides of the furnace and the layer of air will be thinnest over the gas, where it is most needed.

Jan 1, 1914

By W. A. Cole, E. L. Derby, J. F. Wolff

Exploration of Lake Superior iron ores is done principally by drilling. The soft iron ores are churn drilled and the harder ores are diamond drilled. The churn drill used is the Mesabi type and its operation should be described as "water jetting." The drill rods are washed down by the combination action of the water jetting from the bit at the lower end of the rods and the churning motion given the line of rods. The water, which is forced down through the rods, comes up between the wash rods and the casing, bringing the choppings to the surface. It is caught in three or more barrels, each of which has a stoppered hole 8-10 in. from the bottom. These barrels are successively filled, allowed to settle, and drained to the hole, until the desired depth is drilled. The sediment from each barrel is transferred to a settling tub in which it is allowed to settle; the water is then drawn off and the wet sample is collected and dried. The number of barrels used depends on the character of the ore. For example, when drilling sandy ores, all the wash water is caught and settled for the proper length of time without refilling any of the barrels. Thus, the sediment held below the stoppered hole in any one barrel is not disturbed. The casing is kept as near the bottom of the hole as practicable to prevent the caving of the hole from jeopardizing the sample. While the casing is being driven down and the hole is being washed clean after casing, the return water is not run into the sample barrels. In exploratory work in the harder formations, where the diamond drill is used, the sample comprises both core and cuttings. The care given in handling and preserving the core depends on the importance that may be attached to certain characteristic strata in different formations. The following instructions for the care of core samples are issued by the Ogle-bay Norton Co. for diamond drill work done for them on the Gogebic Range of Michigan:

Jan 1, 1925

By Arthur S. Wright

THE accuracy of the silver-assay depends in great measure upon a careful regulation of the heat of the muffle during the process of cupellation. At the beginning of the operation, a relatively high temperature is required to " open " the lead buttons, that is, to clear off the black film of oxide that covers the surface of the metal button immediately after fusion has taken place. The muffle is usually closed up until the buttons are uncovered. As soon as a clear, free surface of molten metal is exposed to the oxidizing action of the air, the temperature should immediately be lowered to the minimum temperature at which the formation and absorption of litharge can progress freely, and the buttons still be kept from " freezing." The process, under satisfactory conditions, will be characterized by the formation of rings of litharge crystals (" feathers," as they are styled), on the cupel, about the oxidizing globule; and the nearer these rings of litharge crystals call be made to approach the central oxidizing globule without interfering with the freedom of oxidation and absorption, the smaller will be the volatilization of silver, and consequeiltly the greater the degree of accuracy attained. This minimum heat must be maintained uniformly during the oxidation of the lead; and just as the last of the lead is disappearing, and the button is preparing to l blick," the temperature of the muffle should be allowed to rise so that the last traces of lead will be driven off. This regulation of the heat calls into play all the skill of the assayer, and requires a vigilant eye, able to distirlguish between the slightest variations of temperature of the muffle, assisted by a nice adjustment of fuel and draft. With a few cupels in the muffle at one time, the proper heat for each cupel can be maintained by roughly approximating the proper temperature, and then moving the cupels backward and forward in the muffle; but this is gene-

Jan 1, 1897

CHICAGO SECTION CHAS. H. MACDOWELL, Chairman, LUTHER V. RICE, Vice-Chairman, HENRY W. NICHOLS, Secretary-Treasurer, GEO. P. HULST, ALEX. K. HAMILTON, FREDERICK T. SNYDER, HENRY P. HOWLAND. The Field Meeting of the Chicago Section proved to be the most enjoyable meeting ever held by the Section. It took the form of a visit to the Northern Indiana Industrial District where the day was spent inspecting metallurgical plants in Indiana Harbor and East Chicago and in amusement at the Hammond Country Club. The weather was perfect and about 50 members and ladies attended the meeting. An inspection of the plant of the Inland Steel Co. occupied the morning. The plant was decorated in honor of the occasion and the company provided attractive souvenirs. It was noticed here that many of the ladies displayed an interest in the inspection and an understanding of the processes that would not have shamed professional metallurgists. While the members of the Section seemed to be most interested in the by-product coke ovens and the by-product recovery plant, the ladies enjoyed especially watching the snake-like antics of the red-hot rods in the wire mill. Leaving the steel plant, the Section enjoyed a ride through the district by automobile and arrived at the Hammond Country Club in time for lunch. In the afternoon some of the members inspected the plant of the International Lead Refining Co., at East Chicago, while the rest spent the time at the Country Club in golf, tennis, trap shooting, bridge and other amusements. During the dinner at the Hammond Country Club an informally organized male quartette led the singing in real college boy style. In the evening, E. E. Billow talked on the use of oil burners in metallurgical furnaces, Mr. MacDowell told of the present status of the Potash Industry and the Secretary told of some of the happenings at the Arizona Meeting. HENRY W. NICHOLS, Secretary.

Jan 12, 1916

By Lester C. Uren

It is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 1, 1925

By S. P. Kinney

Sulfur has been one of the most troublesome elements encountered since the earliest days of iron smelting, and this problem will become of increasing importance as the higher sulfur coke is used, because of the rapidly diminishing supply of low-sulfur coals suitable for the manufacture of metallurgical coke. The deleterious effect of sulfur in iron and steel is well known; therefore, except in special cases, it is desirable to make the iron produced by the blast furnace as low in sulfur as possible. Sulfur enters the furnace in all of the raw materials, but principally in the coke. It comes out of the blast furnace distributed between the iron and the slag; very little passes out of the furnace with the gases. The mechanism of the reactions that cause the sulfur of the coke to pass into the slag and iron has not been studied to any great extent, although the character of the end products, and the conditions controlling the distribution of the sulfur between the iron and slag, are fairly well known. In the iron, the sulfur occurs as ferrous sulfide; or manganese sulfide in case of iron high in manganese. In the slag, the sulfur is present mostly as calcium sulfide. The presence of free sulfur1 and sulfates in blast-furnace slags is to be accounted for on the basis of oxidation of the calcium sulfide after the slag is tapped. The generally accepted reaction for the relation between the ferrous sulfide in the iron and in the coke, and the calcium sulfide in the slag, is that given by Howe? FeS + CaO + CDFe + CaS + CO

Jan 1, 1923

By S. P. Kinney

Sulfur has been one of the most troublesome elements encountered since the earliest days of iron smelting, and this problem will become of increasing importance as the higher sulfur coke is used, because of the rapidly diminishing supply of low-sulfur coals suitable for the manufacture of metallurgical coke. The deleterious effect of sulfur in iron and steel is well known; therefore, except in special cases, it is desirable to make the iron produced by the blast furnace as low in sulfur as possible. Sulfur enters the furnace in all of the raw materials, but principally in the coke. It comes out of the blast furnace distributed between the iron and the slag; very little passes out of the furnace with the gases. The mechanism of the reactions that cause the sulfur of the coke to pass into the slag and iron has not been studied to any great extent, although the character of the end products, and the conditions controlling the distribution of the sulfur between the iron and slag, are fairly well known. In the iron, the sulfur occurs as ferrous sulfide; or manganese sulfide in case of iron high in manganese. In the slag, the sulfur is present mostly as calcium sulfide. The presence of free sulfur1 and sulfates in blast-furnace slags is to be accounted for on the basis of oxidation of the calcium sulfide after the slag is tapped. The generally accepted reaction for the relation between the ferrous sulfide in the iron and in the coke, and the calcium sulfide in the slag, is that given by Howe? FeS + CaO + CDFe + CaS + CO

Jan 1, 1923

By Orville R. Lyons

CENTRIFUGAL force has been utilized for the dewatering of fine coal for over 50 years by means of machines commonly called centrifugal dryers. In any centrifuge the coal and water are subjected to a spinning action which usually inctedtocreases in intensity as the coal progresses through the machine. This spinning action, or the centrifugal force that it induces, tears water away from coal particles and produces a dewatered coal. The effectiveness of the dewatering action for any particular machine is governed by the size-consist of the coal and the centrifugal force imparted to the water on the coal. Four makes of centrifuge are currently being used to dewater fine bituminous coal in the United States. These include the vertical, basket-screen C.M.I. (Centrifugal and Mechanical Industries) Carpenter, Reineveld, and the horizontal solid-bowl Bird. The C.M.I. and Reineveld centrifuges are similar in construction and are variations of the Elmore centrifuge, varying principally in the slope of the basket, operating speed, size of perforations in the basket, and diameter of the basket. The same operating description suffices for both. These centrifuges are made up of two rotating elements, an outside conical screen frame and an inside solid cone which carries spiral pusher blades. The screen frame is supported by a hollow shaft, and the solid cone by a spindle shaft passing through the hollow shaft. Both the screen frame and the solid cone rotate at high speeds; the solid cone, with its scraping flights, rotating somewhat more slowly than the screen. The wet coal enters the machine at the top, falls on the cone, and is thrown against the screen by centrifugal force. The coal slides down the screen until it meets the upper end of the flights, where it is moved slowly along the flights until discharged at the bottom. The elfluent passes through the sieve basket or screen and discharges into a launder. The Carpenter centrifuge consists of a conical rotating element with a vertical axis, built up of three rows of perforated stainless-steel plates or stainless-steel wedge-wire or round-wire sections cut and rolled to conform to the surface of the cone. Wet material is delivered to a conical hopper inside the centrifuge casing and is distributed in a thin, even layer over the inner surface of the cone by a disk mounted on the rotor shaft. Impacting of the coal against the screen and the centrifugal force exerted as the material moves downwards creates a dewatering effect. The moisture is forced through the coal bed and then through the perforated plates of the basket, collecting in a circular trough built into the centrifuge. The effluent is conducted from the trough through the centrifuge casing by outlet pipes. The dewatered coal is discharged over the inside bottom edge of the rotor. The Bird centrifuge consists of a tank or truncated conical shell, which is revolved at the desired speed by means of a drive sheave. A screw conveyor rotates inside the cone or bowl at a slightly lower speed in the same direction of rotation. The feed entrance, in the center of the large end of the truncated cone, is high enough to allow formation of a pool of slurry. Adjustable effluent-discharge ports are located in the large end of the bowl so the level of the liquid can be regulated. The solids are moved forward by the screw conveyor as fast as deposited and carried above the level of the pool for an interval before leaving the bowl. In the past these four makes of centrifuge could be compared only by indirect means. The author published a rough comparison method in 1949' but

Jan 1, 1952

By A. W. Ruff

In the last ten years large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now-prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. In the last ten years, large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. EXPANDING-GAS-BUBBLE THEORY There has been an outstanding change in the conception of how an explosive produces rock failure. The early theory which explained rock breakage was correct for some of the first force-producing agents such as quicklime. When a drillhole was filled with quicklime and water added, the material expanded and steam was generated. The expanding material and the steam exerted a slowly increasing pressure on the sides of the drillhole. The force broke the rock by splitting. Because a great quantity of gas was produced by the deflagration of gunpowder, the same process of the gas pressure splitting the rock was assumed to take place. Even after 80 years of use, the rock-breaking action of all high explosives was thought to be caused entirely by the expanding gas bubble which tore and split the rock. Fig. 1 shows a vertical section through an exploding spherical charge of high explosive. It illustrates the early theory which attributed the entire breakage to the expanding gas bubble. The basic idea of this theory is that the breakage started at the explosive charge and progressed toward the free face. REFLECTED-WAVE THEORY me expanding-gas- bubble theory has gradually been replaced by the reflected-wave theory. The reflected-wave theory explains rock failure by explosives in the following manner: The enormously high gas pressure in the drillhole produces fracturing of the rock on the sides of the drillhole. The fracturing around a 1 1/2-in. diam drillhole is usually confined to an area with about a 6-in. diam. In the fractured area, the pressure of the gas is reduced until the force on the walls is no longer capable of fracturing the rock. Although the gas pressure does not continue to fracture the rock, the pressure imposes a high impact stress on the wall rock. In addition, a pressure or seismic pulse is produced in the rock. The pulse is probably entirely a compression pulse when originally produced in the rock. But, with distance, part of the energy of the compression pulse is transformed into a tension pulse which follows the compression pulse. The explosive charges and burdens used in conventional mine blasting are such that the tension pulse of the original wave is probably too small to be considered in a practical evaluation of the theory. The compression pulse is transmitted through the rock with no associated fracturing.

Jan 1, 1961

By John C. Calhoun, Frank T. Bethel

The application of a method for analyzing pressure build-up curves to determine the effective permeability in the Spraberry is presented. Sixteen upper Spraberry wells of the Driver area arc analyzed and show variations in the in-place effective permeability of 2 to 183 md. Since these value- are much larger than the .5 md. or less reported for the matrix rock. a large part of the vertical fractures noted in Spraberry cores- must be considered native to the formation. The effectiveness of the well fracture treatment in connecting the well bore to the native fracture system is analyzed by comparison of the effective permeability as determined from the PI test to that obtained from a pressure build-up curve. These results show that the fracture treatment is sufficiently effective in connecting tile well bore to the native fractrure system to yield a flow capacity within about 50 per cent of that dictated by the native fracture system About two-thirds of the wells show some degree of local blockage. INTRODUCTION Fractured reservoirs have been known in the past.' However, during the past two years the Spraberry formation has directed the attention of the petroleum industry to a study of the performance of a fractured reservoir. The large variation in the number of fractures noted in Spraberry cores rile large variation in the producing ability of offset well.. the dramatic effect of well treatment on well ,productivity. the unknown quantity of oil stored in the fractures and matrix rock. and the unknown oil to be recovered were part of the initial Spraberry puzzle. In this type reservoir where the well treatment is an important factor in determining the productivity. it i- particularly desirable to determine the in-place flow capacity of the drainage area at distance* far removed from the well bore. This value. when compared to the flow capacity obtained from a PI measurement, will show the effectiveness of the well treatment (completion. fracture treatment, acidization. etc. in establishing a flow capacity in the vicinity of the well bore equal to that in the more remote region. The object of this paper i.; to show the application of a method of pressure build-up analysis for this purpose in studying the Upper Spraberry formation in the Driver area. STATEMENT OF THEORY The theoretical basis for the application of a pressure buildup curve to show the effective permeability of the rock at distances far removed from the well bore has been presented in detail in earlier publications.', in the previous development it was shown that pressure build-up behavior of all wells could be reduced to the same dimensionless build-up curve of Fig. 1. This mean.; that the bottom hole pressure of a well after hut-in will rise in such a manner that a plot of pressure against the logaritllm of time yields a straight line. The slope of this linp can be rlzed to calculate the effective permeability as expressed by the following equation: where: effective oil permeability md oil production rate prior to shnt in. STB/I) In practice the flow which occurs into the well bore after shut in and the variation in flow capacity in the immediate vicinity of the well bore usually cause the early part of the build-up curve to be unsatisfactory in the determination of permeability. In general the effect of these factors on the straight line section will become negligible after a time when the of the following equation is equal to 0.1. and the preferred section Of the curve for use in defining the slope lie-

Jan 1, 1953

By J. C. Donnell, O&apos

Sinking an inclined ventilation shaft at the Never Sweat mine of The Anaconda Co. has required a unique underground hoisting arrangement because the shaft changes direction from vertical to 71.5º. Access to the project is made through the High Ore shaft to the 2800-ft level, then by crosscut to the bottom of the vertical Never Sweat shaft. The 71.5º incline shaft starts at this point, which makes an unusual operation as the 60-cu ft sinking skip coming up the incline changes into a vertical position above the 2800-ft level before going into the dump scrolls. This requires both rollers and guide shoes on the skip. Coming up the incline to the collar of the shaft the loaded skip enters into a guard before reaching the vertical section. The tendency of the surface- mounted Never Sweat hoist is to lift the front wheels of the skip off the track, so the guard keeps the skip on the rails during the transition.

Jan 11, 1965

By Edward Salisbury Dana

THE remarkable advance in the Science of Mineralogy, during the years that have elapsed since this Text-Book was first issued in 1877, has made it necessary, in the preparation of a new edition, to rewrite the whole as well as to add much new matter and many new illustrations. The work being designed chiefly to meet the wants of class or private instruction, this object has at once determined the choice of topics discussed, the order and fullness of treatment and the method of presentation. In the chapter on. Crystallography, the different types of crystal forms are described under the now accepted thirty-two groups classed according to their symmetry. The names given to these groups are based, so far as possible, upon the characteristic form of each, and are intended also to suggest the terms formerly applied in accordance with the principles of hemihedrism. The order adopted is that which alone seems suited to the demands of the elementary student, the special and mathematically simple groups of the isometric system being described first. Especial prominence is given to the "normal group" under the successive systems, that is, to the group which is relatively of most common occurrence and which shows the highest degree of symmetry. The methods of Miller are followed as regards the indices of the different forms and the mathematical calculations. In the chapters on Physical and Chemical Mineralogy, the plan of the former edition is retained of presenting somewhat fully the elementary prin¬ciples of the science upon which the mineral characters depend; this is par¬ticularly true in the department of Optics. The effort has been made to give the student the means of becoming practically familiar with all the modern methods of investigation now commonly applied. Especial attention is, therefore, given to the optical properties of crystals as revealed by the micro¬scope. Further, frequent references are introduced to important papers on the different subjects discussed, in order to direct the student's attention to the original literature. The Descriptive part of the volume is essentially an abridgment of the Sixth Edition of Dana's System of Mineralogy, prepared by the author (1892). To this work (and future Appendices) the student is, therefore, referred for fuller descriptions of the crystallographic and optical properties of species, for analyses, lists of localities, etc.; also for the authorities for data here quoted. In certain directions, however, the work has been expanded when the interests

Jan 1, 1922

A national budget system, which engineers have long regarded as essential to the proper conduct of our fiscal affairs is at last being seriously considered by. Congress and seems likely to be adopted in some form. Several, bills and joint resolutions have already- been introduced but the measure that seems how to attract the 'most attention is H. R. 1201 introduced by. Representative Good, Chairman of the House Committee on Appropriations. This ,bill provides for the creation of a Bureau of the Budget in the office of the President, to which full information shall be furnished by all Departments and other Governmental agencies concerning powers, duties, financial transactions, business method's, etc. A change, is made in the fiscal regulations in that the Departments shall hereafter submit their fiscal estimates to the President instead of to the Secretary of the Treasury, while the latter official shall submit estimates of the public revenues and the condition of the Treasury. Two budgets are, provided for:, The first, or regular, budget shall contain a balanced statement of the resources and liabilities of the Government and the revenues and expenditures, actual or estimated as the case may be, for the preceding, current, and ensuing fiscal years. The President is further, authorized to submit his recommendations as' to how the heeds of the Government should be met, and such further data regarding the financial affairs of the, Government as he deems proper. The second or alternative budget shall make known the essential facts regarding the condition of the Treasury and what, in the opinion of the President. are the revenue, and expenditure needs for the ensuing fiscal year, to be prepared in such form as the President shall deem most appropriate. The bill' abolishes-the offices. of Comptroller of the Treasury and all -the Auditors for the several Departments, and substitutes therefore an Accounting Department, an establishment independent of the Executive Departments, under the direction of newly created officer to be known as the "Comptroller General of the United States" whose powers shall comprise all those now conferred on the Comptroller of the Treasury and the several Auditors and, in addition thereto, the investigation at the seat of Government or elsewhere of all matters relating to the receipt or disbursement of public funds, concerning which report shall be made to Congress at the beginning of each regular session, containing recommendations concerning the legislation deemed necessary to the accurate rendition and settlement of accounts.

Jan 8, 1919

By Edward N. Trump

Extensive beds of rock salt occur in New York, Michigan, Kansas, and Texas. Wells are drilled through the beds, cased, and equipped with a suspended center tube. By circulating water through such a well, the soluble saline is dissolved and a brine produced. Operation of a well results ordinarily in the formation of an inverted conical cavity in the saline, inasmuch as the dissolving action of the fresh water is more rapid at the top of the bed than at the bottom. Under continued operations, the side wall of the cavity becomes so flat that a blanket of mud is deposited thereon and if the bed is overlain with shale or a soft rock caving follows. Three methods of operating wells have been employed—the "Tully plan," "the Detroit plan," and "the Trump plan." Both the Tully plan and the Detroit plan involve the formation of the aforesaid conical cavity with constant caving of shale above and deposition of mud on the side wall; the Trump plan was developed to avoid both these circumstances and thus materially prolong the life of a well. Details of the three plans follow. The Tully Plan In the Tully plan, the water passes down the annular space between the casing and the center tube, the brine rising in the center tube (Figs. I and 2). An inverted conical cavity is formed, the side wall of which relatively soon becomes so flat that it is blanketed by mud and impurities from the rock salt; this blanket limits dissolving action to the perimeter of the base of the cone, situated at the top of the saline bed. Caving of the overlying strata follows, and the total production of brine from the well is comparatively small. The Detroit Plan In the Detroit plan, the water passes down the center tube, the brine rising in the annular space between the center tube and casing (Figs. I and 2). Initially, this flow forms a pear-shaped cavity in the bottom of the salt bed, but this cavity soon changes in shape to that of an inverted cone, as under the Tully plan, with the attendant disadvantages inherent in that plan. Application of the Detroit plan is limited to salt beds 300 ft. thick as a minimum. This depth of bed is necessary to prevent fresh water of lower specific gravity than the brine from rising in the

Jan 1, 1948