Search Documents

By W. H. Bassett, J. C. Bradley

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. 11 is suggested that the materical is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the shad. Figures 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent. Structure of Protuberances The segregation of oxide between grains in the interior of the cast bar, not far from the "set," is shown in Figs. 5 and 6. In general, the amount of cuprous oxide begins to increase at a point about 0.01 in. below the normal surface of the casting, i. e., the base of the drop; but it does not attain maximum concentration in the main body of the metal. Vertical sections, Figs. 7 to 12, show that there is a definite line of large cuprous-oxide globules at the base of the drops. Horizontal sections at this place show that these large globules lie in a thin billowy

Jan 1, 1926

By Aug. J. Jr. Bowie

(Read at the Wilkes-Barre Meeting, May, 1877.) Brief Outline of the General Topography of the Gold Regions of California. THE topographical features of California, as demonstrated by the explorations of the State Geological Survey, are found to be exceedingly simple. Three equidistant parallel lines can be used in conveying a general idea of the physical geography of Central California. A straight or " main axial line," whose course would be north 31° west, passing through the culminating peaks of the Sierra for a distance of five hundred miles, can be assumed as the eastern boundary of the State. A second parallel drawn fifty-five miles west of the " main axial line" will skirt the western base of the Sierra Nevada, along the edge of the foot-hills. A third parallel run equidistant from the second will represent "as nearly as possible the western base of the Coast Ranges." These parallel lines divide the State into three belts, namely, the Sierra, the Great Valley of California, and the Coast Ranges. " This arrangement of the physical features holds good for a length of four hundred miles in the direction of the main axial line, comprising almost the whole of the agricultural and the greater part of the mining districts."* The section of the country which is of immediate interest to the miner is the western slope of the Sierras. These mountains, rising in a short distance from the Sacramento plains to elevations of over seven thousand feet, with occasional peaks ten and twelve thousand feet high, are cut by numerous deep and precipitous gorges or capons, through which drains the immense watershed of the Sierra, supplying the main rivers of the State and ultimately emptying into the Pacific Ocean. Between these capons, ridges or divides are formed, on top of * See vol. i, p. 5, Geological Survey of California. J. D. Whitney, State Geologist.

Jan 1, 1878

By E. P. Polushkin

The object of this paper as to show that the structural composition of an alloy may be found by the planimetric measurement of the total area occupied by each of the constituents on a few representative photomicrographs of this alloy. When the area is determined the volume and the proportional weight of the constituent may be calculated. This method has been used for the determination of the structural composition of binary eutectics and other binary alloys with known constituents; also the composition of unknown constituents in binary alloys. The accuracy of the method is. high enough to justify its application to metallographic problems instead of the chemical analysis. THIS work has for its purpose the establishment of a new method for determining the structural composition of alloys. The area occupied by a constituent on a few representative photomicrographs of the alloy is measured, by a planimeter, especially designed for metallographic work, and the volume and proportional weight of the constituent calculated. Experiments have shown that 'the results are accurate enough to justify the application of the method to many problems in metallographic research instead of chemical analysis. The advantage of the method is the possibility, of determining the amount of the constituents with-out separating them from the alloy; their composition may also be determined if the ultimate chemical analysis of the alloy is known. DESCRIPTION OF PLANIMETER Suppose Fig. 1 represents a part of a photomicro-graph on which the total area of the black figures is FIG. 1?-PART OF PHOTOMICROGRAPH ON WHICH TOTAL AREA OF BLACK FIG- URES IS TO BE FOUND. to be found. By a system of parallel lines drawn short equal distances apart all figures may be divided into trapezoids. As the area of a trapezoid is equal to its median multiplied by its altitude, the relation between the total areas of the black and the white figures comprised within each strip is equal to the relation between the sums of medians for these figures respectively.

Jan 12, 1924

By Mark Sheppard

DURING the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the over- burden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semi- circle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and 800 ft. of 4-in. spiral steel flanged pipe. The connection from the pump

Jan 1, 1938

By B. W. Frazier

IN the numbers of the Engineering and Mining Journal of June 27th and July 11th, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced to the same standard of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given -by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of the pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part of the furnace, by the dissocia¬tion of carbonic oxide, is again converted into carbonic oxide or

Jan 1, 1875

By B. W. Frazer

In the numbers of the Engineering and Mining Journal of June 27th and July llth, 1874, there appeared some very complete statistics of the working of some anthracite blast-furnaces belonging to a large establishment in this country, followed by calculations of the heat requirements of the furnaces, similar to those which have been made for European furnaces by Mr. I. Lowthian Bell, Prof. Gruner, Prof. Akerman and others. To the author of these valuable papers, Mr. John A. Church, of New York, the thanks of American iron metallurgists are due for this attempt (the first, to my knowledge at least), to attack systematically and scientifically the problem of economy of fuel in our anthracite blast-furnaces, by applying the formulas obtained from European practice and from the experiments of European metallurgists, to the determination of the amounts and the modes of distribution of the heat production and absorption in our furnaces. In order to facilitate a comparison of the results thus obtained for the anthracite furnaces in question with those obtained for the best types of European coke furnaces, I have reduced 60 the same standad of heat units (the product of the ton and the degree Centigrade), and placed side by side, the calculations of the heat requirements of one of the furnaces of the Clarence works, as given by Mr. Bell, of a furnace at Pouzin, on the banks of the Rhone, given by Prof. Gruner, and of the anthracite furnaces for 1869-73, as given by Mr. Church. Table I shows the different conditions of working of the three furnaces, of which Table II gives the respective heat requirements. I have made this latter table in such a manner as to give for each furnace its heat requirements, both according to the views of Mr. Bell and those of Prof. Gruner. Mr. Bell assumes that all the carbonic acid produced by the decomposition of the carbonate of lime of the charge, is reduced to carbonic oxide by contact with solid carbon ; also, that the carbon of t,he pig iron is a portion of that deposited in the ore in the upper part of the furnace, by the dissociation of carbonic oxide. Prof. Gruner, on the other hand, assumes that all the carbonic acid of the carbonates of the charge escapes unreduced, and that the carbon deposited in the upper part. of the furnace, by the dissociation of carbonic oxide, is again converted into carbonic oxide or

By J. J. Taber, I. S. K. Kamath, R. L. Reed

Alcohol floods of consolidated sandstone cores have shown the process to be strongly dependent on the phase behavior of the particular alcobol-oil-water system used. This means that in many cases the mechanism does not conform to the idea of a piston-like displacement. Instead, it is found that by changing the alcohol it is possible to change the relative velocities of the oil and water and, in fact, the entire mechanism of the process. The effects of rate, viscosity, initial saturation, distance travelled and hysteresis of relative permeability on the alcohol flooding mechanism are discussed. INTRODUCTION Reasons for interest in the use of alcohol to miscibly displace oil and water from a porous medium appear in the existing literature.l-7 The mechanism of the displacement has been considered and the apparent implications formulated into a theory which presumably would enable one to predict the essential features of the process.6 Unfortunately, most of the reported experiments have been performed with unconsolidated or artificially consolidated sands. With these systems some of the noteworthy facets of the process are obscured and resulting data appear uncertain. It is the purpose of this paper to show how the use of consolidated sandstones has led to revision of the mechanism and, hence, the theory of alcohol flooding. The practical result is increased pessimism toward the possibilities of commercial application of the simplest form of the alcohol-slug process. However, elucidation of the mechanism has made it possible to define the essential characteristics of a system of slugs which will behave in a nearly piston-like fashion and, thus, yield the best possible result. EQUILIBRIUM PHASE BEHAVIOR Fig. 1 is a diagram of the ternary system isopropyl alcohol (IPA)-Soltrol-calcium chloride brine. Brine was used to prevent plugging of the core and calcium chloride was used because sodium-chloride brine exhibits a solid phase with Soltrol and IPA. If alcohol is added in increments to the immiscible mixture of water and oil represented by Point A, the path followed by the successively equilibrated samples will be on the Line ABC and pass from the immiscible region to the miscible region by crossing the binodal curve at B. Consider the intersection D of this path with the tie Line EF. The quantity of oleic phase is proportional to the Segment ED and the quantity of the aqueous phase is proportional to DF. Compositions of the two phases are specified by Points E and F. It is clear that in the case shown the oleic phase is diminishing and entirely disappears when miscibility is achieved. Such will

By G. H. Gilman

The campaign now being waged to improve the quality of the rock-drill bit is the natural outcome of the scientific development of the drilling machine during the past twenty years. In this development there has been a great increase of power output per unit of weight of machine. But the development of the rock drilling engine has been seriously hampered by the need of a drill bit that would withstand, without undue wear or breakage, the heavy rapid blows of the improved pneumatic hammer. This problem was difficult to solve because an increase in the weight or section of the drill-steel bar resulted in decreased cutting speed and higher operating costs of both the bit and its actuating engine. The solution, therefore, is to make the bit of steel that, for a given weight or section, will be more shock and wear resisting. In the attempt to meet these requirements, many of the drill-steel manufacturers alloyed the steel with vanadium, chromium, nickel, etc. on the assumption that such elements would improve the rock-drill bit but due to the sensitiveness of such steel to forging and heat treatment, higher cost, and lack of continuity of effort on the part of the steel manufacturer to perfect this product, but little progress has been made in the adoption of these steels and the so-called straight carbon steel is today recognized as the standard material for all rock-drill bits. The first step in improving drill-bit efficiency is the determination of the cause of breakage and wear. For this reason, in 1917, certain rock-drill manufacturers, in conjunction with some of the larger mining interests, conducted exhaustive tests in both the field and the laboratory. It was then found that, in the main, the cause of drill-steel troubles is not attributable to the duty imposed upon it by the normal operation of the drilling engine, but to improper forging and heat treating of the bit and to the subjecting of the bit to improper use. The fact that it is possible to minimize the troubles attributable to improper heat treatment of the drill steel has been demonstrated and it is recommended that such knowledge be made available by teaching those interested in the production, use, and up-keep of drill bits the principles on which success in this direction may be achieved. Unfortunately, but little attention has been given to the education of the drill smith. But a few years ago, the instructions given the man

Jan 1, 1922

By C. E. Mills

The Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district—the United Verde and the United Verde Extension—lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Woodchute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. T-bis strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the

Jan 1, 1925

By David Cornell

Back pressure test data on natural gas wells are short time test data of unsteady state nature. Performance curves from which unsteady state effects have been eliminated, called stabilized performance curves, are necessary for understanding the behavior of gas wells and for scheduling gas fields for periods up to 20 years. A calculation procedure has been developed whereby three day, seven day, 30 day, or other duration stabilized performance curves may be calculated from back pressure test data. Such curves are essential for correct gas deliverability calculations and gas field scheduling. I NTRODUCTION The manner in which a back pressure test is made will affect the slope of the back pressure curve because the radius of drainage changes with the length of time that the well is allowed to flow. The reciprocal of the slope of the back pressure curve is defined as n in Equation 1 and varies from 0.5 to 1.0. If the flow is viscous and the radius of drainage constant, n will have a value of 1.0. Because of turbulence in the formation near the wellbore, the pressure drop is usually greater than the viscous flow pressure drop and the exponent n is frequently less than 1.0. In addition, since the radius of drainage moves away from the well-bore during the test, the gas flows a greater and greater distance as the test proceeds, with a resulting increased pressure drop at the high flow rates, and, again, n for the test tends to be less than 1.O. The effect of the changes in the radius of drainage may be calculated and the results used in preparing stabilized performance curves for fixed values of the radius of drainage. Such curves can be made for a defi- nite time period, such as three day, seven day, or 30 day stabilized performance curves. These cukes will show the effect of turbulence near the wellbore and can be used to predict the performance of the gas well at any flow rate or for any production period. In order to discuss the importance of the radius of drainage quantitatively, it should be defined. Muskat" defines the radius of drainage as follows: "... the radius of drainage gives the distance from the well to which the approximately steady state condition has been established ... it being assumed that no gas is removed from any point until the radius of drainage has passed that uoint." An eauivalent definition of the radius of drainage is that radius at which the extrapolated portion of the steady state portion of the pressure gradient gives a pressure equal to the shut-in reservoir pressure. This definition is also implied in the back pressure equation. The radius of drainage is, then, the distance into the reservoir from which the gas appears to originate at any time. It is, however, only a useful concept and does not actually exist. Fig. 1 illustrates the definition of the radius of drainage. At the end of each flow period the radius of drainage may depend on three factors: (1) the duration of each flow period; (2) the rate of gas production; and (3) the rate and duration of the previous flow periods. In general, back pressure tests are conducted with various lengths of production time and at various flow rates. Each individual back pressure test, therefore, requires an individual analysis. The calculations of the change in the radius of drainage have been made, however, for the case of equal flow periods for all four production rates and several sets of increasing flow rates. Fig. 2 illustrates the results of such calculations made by the method of Cornell and Katz2 for the case of 8, = 50,000 and the flow rate increasing in the ratio 1.0:2.0:3.0:4.0 for each flow period. The increase in the radius of drainage during the test is apparent.

Jan 1, 1956

By M. P. Tixier, A. Poupon, M. E. Loy

Simple qualitative methods are explained for identifying those shaly sands in a well that are most likely to contain oil. A need for more precise measurement of the variables that enter shaly sand analysis is indicated. Field examples are given to illustrate the methods. A theoretical discussion of the quantitative interpretation of shaly sands is given as a basis for discussion and as a guide for the future. While not generally capable of practical application at the present time because of the lack of sufficient accuracy of the electric log data, these methods may become more feasible in the future as the result of the improved logging methods now being introduced. INTRODUCTION Experience has shown that for porous formations containing only a negligible amount of clayey material, reliable information on the fluid saturation and porosity of the reservoir rocks can usually be derived from the electrical logs. The interpretation is based on empirical formulae relating the true resistivity of a porous formation to its lithologic character, to the resistivity of the interstitial water, and to the proportions of water and hydrocarbons in the pores.' If the resistivity of the interstitial water is not known, its approximate value can be derived from the SP curve.2,3 The porosity can usually be determined to a good approximation from a MicroLog, or a MicroLaterolog.4,5 When the reservoir rocks contain an appreciable percentage of clayey material, an additional factor is introduced into the analysis. In a clean formation, the matrix is an electrical insulator, so that the ability of the formation to conduct current is due only to the conductivity of the electrolytes in the pores; in a shaly formation, the shale constitutes a part of the rock matrix able to conduct current, and influences the resistivity of the formation. On the other hand, the spontaneous emf's and the circulation of the SP currents are also responsive to the presence of the shaly material. All other factors being the same, the deflection of the SP curve opposite a shaly permeable formation is smaller than the deflection which would be observed if the formation were clean. The effects of the presence of shale on the resistivity and on the SP curves in a shaly formation are functions of the amount, of the specific resistivity, and of the geometrical distribution of the shaly material within the formation. The presence of shale therefore constitutes an important complication in electrical log interpretation. It is easy to realize, for example, that the presence of a large amount of clayey material in a sand may have such a predominant effect that the resistivity of the sand will not change very much, whether the pores are entirely filled with connate water, or contain a high saturation of hydrocarbons. Important research projects have been undertaken to investigate the influence of shales and to find a way to allow for this influence in the interpretation of a log. The problem of the SP in shaly sands was analyzed mathematically by H. G. Doll"' for the case of sands with shale laminations. Formulae expressing the resistivity of shaly formations were proposed by Patnode and Wyllie8 and de Witte.9 Other quite interesting theoretical and experimental results have been published by various authors.l0,ll,12,l3,14 The purpose of the present paper is to discuss an approach to electrical log interpretation in shaly sands. This approach is based partly on some of the theoretical and experimental data available in the literature and partly on observations made on actual field logs. Comparatively simple methods for qualitative and semi-quantitative analysis are described. These methods depend principally upon information provided by the electrical logs.

Jan 1, 1955

By J. Gurland

The effect of four different second-phase additions on the strength of composite alloys with a common matrix was investigated. The four compositions each consisted of 85 pct by volume of silver with additions of 15 pct of either tungsten, molybdenum, tungsten carbide, or nickel. These particular additives were chosen because of their low mutual solid solubilities with silver at room temperature, the alloys consisting essentially of a dispersion strengthened silver matrix in which the second phase is distributed randomly. Test specimens were prepared by a powder metallurgy procedure consisting of ball milling the mixed powders, compacting, and sintering at 920°C for 1 hr in hydrogen. The constituent powders were of CP quality and of particle size between 2 and 10 ?. The compacts were subsequently hot pressed at 1000 psi and 1400° in an Inconel die, coined at room temperature at 60,000 psi and finally annealed and outgassed in vacuum at 800°F. The microstructures of the alloys are shown in Fig. 1, and the microscopically observed porosity grade was A-2 or better as evaluated by ASTM Recommended Practice B 276-54. The properties of the sintered compacts are listed in Table I, and the load-deformation curves in bending are shown in Fig. 2. The samples, of rectangular cross section, were loaded at the center of 58 in. span, and the reported stress was calculated on the basis of linearly elastic behavior in order to allow the comparison of specimens of slightly different dimensions. It is apparent that the tungsten, molybdenum, and tungsten carbide alloys exhibit very similar deformation curves. The moduli of elasticity were determined from the slopes of the stress-deflection curves at small loads. The measured values agree quite well with those calculated by the strength of materials approximation proposed by Paul1 for the elastic constants of mixtures, the calculated values being 15.0, 15.0, 17.4, and 13.4 million psi, respectively, for the tungsten, molybdenum, tungsten carbide, and nickel combinations with silver. The strength of the Ag-Ni composition is appreciably lower than that of the other three alloys. The discrepancy between the two groups is accounted for by the following characteristics of deformation and failure which were observed microscopically during the tests: A) The deformation of the W, Mo, and WC alloys did not involve the second phase particles to any appreciable extent. Slip and fracture took place in the silver-rich matrix alone, although the fracture path generally skirted the particles by favoring the phase boundaries. The deformation proceeded according to the following sequence: 1) formation of small, discontinuous microcracks in areas of the matrix adjacent to a particle, 2) general slip in the matrix and extension of cracks, 3) failure of specimens by propagation of cracks through matrix. The near coincidence of the 3 load-deflection curves suggests that the nature of the second phase particles does not decisively influence the plastic behavior of composite alloys of this composition as long as the particles do not undergo any considerable deformation themselves. B) A markedly different behavior was exhibited by the Ag-Ni composition where the relatively low flow strength is associated with the low yield strength of the nickel grains. Slip in the nickel grains was first observed at a stress of approximately 10,000 psi, although failure, at a later stage, took place by the propagation of cracks through the matrix. The ductility of this aggregate, in which both components deform plastically, is appreciably greater than that of the elastic-plastic composites. In summary: 1) The measured values of the moduli of elasticity of the composite alloys under discussion are in good agreement with the "strength of materials" approximation proposed by Paul.' 2) The overall plastic behavior of these particle-strengthened alloys is unaffected by the nature of the second phase particles, if the latter remain elastic. This work was supported by the Office of Naval Research. The experimental results are presented

Jan 1, 1962

By Pradeep K. Rohatgi, Clyde M. Adams

Structures produced upon solidification of the eu-tectic composition (33 wt pct Cu) aluminum copper alloy have been examined as a function of freezing rate dfs /d? , the rate of change of fraction solid (fs) with time (8). Slow (dfs/d? = 0.0016 sec-1), intermediate (dfs/d? = 0.02 sec-1) and rapid (dfs/d? = 0.4 to 7.30 sec-1) freezing rates were used. The lamellar Al-Cual2 eutectic is arranged in the form of rod-shaped colonies at rapid freezing rates. The colonies are aligned parallel to the direction of heat flow, whereas the lamellae within the colonies are aligned at various angles, as high as 90 deg, to the direction of heat flow. The colony spacing (C) is proportional to the square root of inverse freezihg rate. The relationship is C = 15.5(dfs/d?)-1/2 where C is in µ and 8 is in sec. The ratio of colony spacing to lamellar spacing is greater than 20.0 and increases with a decrease in the freezing rate. A duplex dendritic structure is produced at intermediate freezing rates. A fine lamellar eutectic is arranged within the dendrites (exhibiting side branches at an angle close to 60 deg from the main stem) and a coarse irregular eutectic appears in the interdendritic regions. The duplex eutectic structure is also produced at slow freezing rates. However, at slow freezing rates there is a Platelat of CuAl2, along the center of the main stem of each dendrite and the other lamellae are arranged perpendicular to the central platelet. THE eutectic between CuA12 and a! aluminum has been reported to freeze in a lamellar form by several workers.'-3 chadwick4 has measured the interlamel-lar spacing as a function of growth rate. Kraft and Albright2 have reported on irregularities in the lamellar structures, and have proposed growth models which account for the formation of faults during solidification. In certain instances the lamellar eutectic has been found to exist in colonies. The colony formation315 has been attributed to the breakdown of a planar liquid-solid interface due to rejection of impurities. The aim of the present work is to study the structures produced from the eutectic aluminum-copper alloy under relatively fast solidification rates, such as encountered in casting and welding operations. The solid-liquid interface presumably remains planar under conditions of slow unidirectional freezing which produce lamellae aligned parallel to the direction of heat flow. The local growth velocities are the same over the entire interface and are equal to the rate of growth of the all-solid region. The spacing between the eutectic lamellae is inversely proportional to the square root of the growth rate of the all-solid region. Under the freezing conditions used in the present study, the solid-liquid interface is cellular or dendritic and the local growth velocities are different in the different regions of the interface. The relationship between the growth rate of the all solid region and the local growth velocities varies with the location and the shape of the interface. The growth rate of the all-solid region is, therefore, an inadequate parameter to describe the eutectic micro-structures which depend upon the local growth velocities. For this reason the structures have been examined as a function of freezing rate, dfs/d?, where fs is the fraction solidified at time 0. The freezing rate was varied by a factor of 4000. The relationship between the freezing rate, dfs/d?, and the growth velocit of the all solid region depends upon the specimen geometry and the shape of the interface. EXPERIMENTAL PROCEDURES The A1-33 pct Cu alloy used throughout this study was made in an induction furnace, using electrolytic copper and aluminum of commercial purity (99.7 pct), the primary impurities being silicon (0.12 pct), iron (0.14 pct), and zinc (0.02 pct). Three ranges of freezing rates were investigated: 1) A spectrum of rapid freezing rates (ranging from 0.40 to 7.30 sec-1) was obtained in arc deposits made on 2-in. thick cast plates of the eutectic alloy. The arc was operated at constant power and was made to travel at constant velocity on the surface of the plate that was in contact with the chill surface during solidification. The pool of liquid metal formed under the moving tungsten arc solidified rapidly by heat extraction through the unmelted plate. Conditions of unidirectional heat flow were achieved near the fusion zone interface, especially in the center of the arc deposits. The great advantage of the arc technique is that rapid cooling and freezing rates can be varied in a qualitative way. The correlation between the arc parameters and the solidification rate is given by the following relationship:6-8

Jan 1, 1970

By A. S. Odeh

During the last few years, several authors1-6 have advanced mathematical solutions, both exact and approximate, to the pressure behavior of a well producing from a region bounded by a circular discontinuity. The most recent solutions were reported by Carter, and by Bixel and van Poollen. Varter solved the appropriate equations analytically. Bixel and van Poollen reported a numerical solution and provided correlation charts for the interpretation of flow tests; their method uses an overlay technique and is valid for wide ranges of mobility and storage capacity ratios. The mobility ratio is defined as the ratio between k/p of the two zones, and the capacity ratio is defined as the ratio between $c of the two zones. We have developed independently an analytic solution, programmed for the CDC 1604, that agreed with Carter's.'1 The same differential equation, assumptions, boundary, and initial conditions were used. We ran 30 drawdowns and 30 buildups of a unit capacity ratio and of varied mobility ratios. We also varied the radial distances to the discontinuity, and the radii of drainage. We examined the results and obtained correlations that were simple to apply and useful in flow test interpretation. The results and the correlations reported here in graphical form allow the determination of the mobility of the two zones and the radial distance to the discontinuity. They eliminate the need to fit field data to a curve as is required in the overlay technique.6 Thus, the advantages of the present correlations are that they require less effort and they provide a unique answer. They also provide guidelines for selecting the parts of the flow test plot to be used in the interpretations. Moreover, the results obtained from the programmed analytic solution define the time intervals where the approximate solution reported by Hurstl and discussed by Larkin2 are applicable. Normal buildup and drawdown plots resulted in an early straight line, a long transition zone and a late (second) straight line. However, the second straight line will not occur if the drainage radius is not at least 10 times the radial distance to the discontinuity. The mobility of the imer and outer zones can be calculated from the slopes of the first and second straight lines, respectively, by the normal methods of the flow test analysis. We found that the radial distance to the discontinuity may be determined from the abscissa value for the point of intersection of the extensions of the two straight lines. Results similar to some of these were reported by Adams et aL7 The approximate solution compared favorably with the exact one during the first and second straight-line periods. However, during the transition zone, deviation occurred between the two solutions. Discussion of Figures Figs. 1 through 7 summarize the results of this investigation. On Figs. 3 through 7 there appears the equation of each respective plot. In this paper the mobility ratio M is defined as klp2/kzpl, where subscripts 1 and 2 refer respectively to the inner and outer zones, and dimensionless time = t, = 6.32 X In the investigation, M ranged from 0.25 to 50;

Jan 1, 1970

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant&apos;s elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

By N. Mungan, J. L. Thompson

Laboratory displacement tests were performed to study oil recovery elficiency by gravity drainage in fractured systems under miscible conditions. The porous media used were cylindrical Berea and Blue Jacket sandstone cores containing a number of well-defined, artificially formed, vertical and subvertical fractures. Butane and Soltrol 130 were the two miscible fluids used. The purpose of the study was to examine the influences of the displacement rate, fracture density, fracture orientation, fracture permeability, matrix permeability, crossflow, core length and connate water on the oil recovery. It was found that displacement rate, matrix permeability and the subvertical fractures affected oil recovery most. The critical flow rate, based on the matrix permeability, was found to be a significant factor in the process. For displacement rates below the critical flow rate, the oil recovery efficiency appeared to be unaffected by the density of the subvertical fractures. At the high displacement rates, the fracture density becomes important, with the recovery being the most efficient in the core having the greatest number of the subvertical fractures. The magnitude of the fracture permeability, the fracture orientation, the core length and the connate water have little effect on the oil recovery efficiency. INTRODUCTION Gravity drainage under miscible conditions from relatively thick reservoirs can be a very efficient recovery process, especially at low flow rates where the gravity forces are dominant and, consequently, the adverse viscous fingers associated with the unfavorable viscosity ratio are minimized or eliminated. Such a process might involve injection of an LPG or some solvent bank at the crest and then driving the bank with dry gas. For some favorable combination of reservoir temperature, pressure and oil composition, there may be no need to inject any solvent bank, since enrichment of the dry gas by the light ends of the crude creates an in-situ solvent bank. Slobod and Howlett2 have studied the effects of gravity segregation in vertical unconsolidated porous media under miscible conditions in the laboratory. The main variables in their study were the viscosity ratio, the density differences and the rate of flow. In this study, the objective was to find the influence of fractures on gravity drainage under miscible conditions. A greater number of related variables were also studied. LABORATORY STUDY CORE DESCRIPTION Displacement tests were performed mostly in cylindrical Berea sandstone cores. In a few cases in which a much lower matrix permeability was desired, Blue Jacket sandstone cores were used. The vertical fractures were formed by cutting the cores with a thin circular blade or by parting them along a bedding plane. The vertical fracture plane always contained the axis of the cylindrical core. The subvertical fractures, cut with a saw, were inclined 45&apos; from the horizontal. The line of intersection between the planes of the vertical and subvertical fractures was parallel to the circular faces of the cores in all cases except one, as depicted by VF3HF-2 in Fig. 1. Fracture geometry of the other cores is also given in Fig. 1. Tables 1 and 2 give the physical properties of the solid and fractured cores, respectively. The suffixes and prefixes shown for each core have been used throughout the paper so that the reader may discern the fracture geometry from the core numbers.

Jan 1, 1970

MINING AND METALLURGICAL SOCIETY OF AMERICA San Francisco Section The San Francisco Section of the Mining and Metallurgical Society of America held a joint meeting with the local section of the American Institute of Mining Engineers at the Engineers&apos; Club, San Francisco, on Tuesday, Apr. 16, 1918. The meeting was preceded by a dinner. Letters from the parent body in NewYork asking for the consideration of the proposed bill before Congress, and an expression of opinion relative to the appointment of a Federal Administrator of Mines justified the joint meeting of the local sections of the two mining societies, in that a more representative opinion of the engineers of California could he obtained. The meeting was called to order at 7:15 P.M. by Mr. Frank H. Probert acting as Chairman. About thirty engineers were present. Mr. Probert read a letter of March 14, from Secretary Huntoon, asking that the meeting be called. He read excerpts from Bulletin 117 of February 28, 1918, of the Mining and Metallurgical Society containing a copy of the proposed bill, so that all present might be advised of its essential contents. He briefly commented on the urgent need of such legislation and invited discussion of the subject. After long and thorough discussion on the part of the members present, Professor Lawson made the following motion: I move that a resolution expressing the sense of the joint meeting of the local sections of the American Institute of Mining Engineers and Mining and Metallurgical Society of America be forwarded to the secretaries of the two societies to the effect that we heartily approve of the purpose and intention of the bill designed to promote and stimulate the production of minerals necessary for the successful prosecution of the war; and that we suggest prices should be fixed for the period of the war and two years thereafter, and that these prices, guaranteed by the Government, should apply at the nearest shipping point to place of production of the minerals. This motion was carried. The meeting then adjourned, and a telegram was sent by Mr. Probert, the Chairman, to Mr. Huntoon, notifying him of the motion that had been carried at the meeting.

Jan 7, 1918

By E. P. Palmatier

RECENTLY a cooling system has been in process of installation on the 3400 and 3600-ft. levels of the Magma copper mine at Superior, Ariz. The general system of ventilation employed at this inclined-vein mine is as follows: Ventilating air enters the shafts on the western side of the mine. Booster fans at each level each deliver approximately 38,000 cu. ft. per &apos;min. to the drifts. This air passes diagonally upward to the upper levels of the mine on the eastern side, where it passes up the shafts to large exhaust fans on the surface. Owing to the dip of the vein, all operations on the eastern side of the mine are above the 2500-ft. level, and those on the western side below the 2500-ft. level. At present, 2500 lineal feet of new drifts are being driven-on each of the 3400 and 3600 levels. The rock temperature is about 135°F. Until the new installation is completed, ventilating air for the two levels is supplied through Flexoid tubing from small booster fans -on the 3200-ft. level. The air picked up by these booster fans has a dry-bulb temperature of approximately 85°F. and a wet-bulb temperature of 82°F. By the time this air reaches the end of the Flexoid tubing at the 3600-ft. level, the dry-bulb rises to 101°F. and the wet-bulb to 86°F. The conditions at the head of the new drift were 102&apos; dry-bulb and 93&apos; wet-bulb.

Jan 1, 1937

By N. Brown

From the theories of flow and fracture it is shown that the difference in reciprocals of the transition temperatures (OK) is a quantitative measure of temper ernbrittlement. Experimental data are given which support this conclusion. STUDIES of temper embrittlement have been made with various viewpoints; some involved a study of the kinetics of the reaction,&apos;,2&apos;" others were concerned with changes in the mechanical properties," . and still others investigated the structural differences between the embrittled and unembrittled states by means of the microscope," -ray ,&apos; measurements of electrode potential," and electrical resistivity." In all these studies, the difference in impact properties was the criterion for distinguishing between the embrittled and unembrittled states. By common agreement the difference in transition temperatures is now taken as a measure of the degree of embrittlement, and this measure is used as the quantitative measure upon which studies of the phenomenon are based. Vidal and Jolivet"&apos; suggested that the degree of embrittlement was the same whether measured by impact or by a slow bend test. Their conclusion was based on tests at constant temperature. Jaffe and Buffum" using the impact and slow bend test showed that, for a given degree of embrittlement, the difference in transition temperatures varied with the method of testing. Hultgren and Chang" showed that the difference in transition temperature produced by the V-notched Charpy impact test was not the same as the value produced by the keyhole-notched impact test. This is a very fundamental point because there can be no true measure of temper embrittlement unless it is invariant with respect to the test method. Theory The purpose of this analysis is to show how the transition temperature depends on the stress distribution and the state of the material. The criterion for fracture may be stated as follws: where iF is some function of the principle stresses and F is a critical condition depending on the state of the metal. Similarly yielding occurs when Where is another function of the prin-ciple stresses and Y is a critical value depending on the state of the material. There is some controversy as to the exact form of the function f,.(u,, u,, us) but most experimental data give the following criterion:= where 8, and 6, = 21 or 0. Combinations of 6, and 8, give the various criteria such as the normal stress, the hydrostatic tension, and the maximum shear stress laws. Agreement is general that the octahedral shear stress law adequately describes the yield condition. where the bracketed factor will be called the design factor and depends on the stress distribution. Whether the metal decides to yield or fracture is given by the condition that The effect of temperature and strain rate upon Y has been studied by various investigators, It has been shown by MacGregor and Fisher" that

Jan 1, 1955