Search Documents

By H. H. Pentz

This paper gives the derivation of a practical formula for the calculation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 260 ft. per 1000. Derivation In Fig. 1, o represents the image of the shot point a. Then the length of the path acb is equal to ob and ae'd is equal to od. In the triangle aob, p is equal to ob, x is equal to , and c is equal to ao. The angle u is the apparent dip of the reflecting horizon. Angle oab is equal to (90" - u). The quantity m is the slope of a line tangent to the curve, defined by equation 1, at the point (p, x). The quantity m' is the slope of the line tangent to the curve at the point (p', 2').

Jan 1, 1940

By H. H. Pentz

This paper gives the derivation of a practical formula for the calculation of slopes in seismic reflection prospecting. The derived formula is an approximation and can be used where the slope of the reflecting horizon is less than 250 ft. per 1000 and the depth to the reflecting horizon is greater than 2500 ft. The slope of sediments in oil regions is generally considerably less than 250 ft. per 1000. This is particularly true of the Gulf Coast, with the exception of the salt domes, which usually have the sediments at a greater slope than 260 ft. per 1000. Derivation In Fig. 1, o represents the image of the shot point a. Then the length of the path acb is equal to ob and ae'd is equal to od. In the triangle aob, p is equal to ob, x is equal to , and c is equal to ao. The angle u is the apparent dip of the reflecting horizon. Angle oab is equal to (90" - u). The quantity m is the slope of a line tangent to the curve, defined by equation 1, at the point (p, x). The quantity m' is the slope of the line tangent to the curve at the point (p', 2').

Jan 1, 1940

Meeting of Nov. 21, 1913.-The President reported the appointment of the officers and members of the Committee on Non-Metallic Minerals, published elsewhere in this Bulletin. The President appointed the Executive Committee of the New York Section as a local .committee to have charge of the Annual Meeting of the Institute in February, 1914, with power to add to their numbers. It was voted that the Chairman of each Technical Committee, be made ex officio a member of the Committee on Papers and Publications. At the request of the Secretary, Burr A. Robinson was appointed Assistant Secretary of the Institute. E. Gybbon Spilsbury was nominated as representative of the Institute on the John Fritz Medal Board of Award. It was voted that the next summer meeting of the Institute be held in Salt Lake City in August, 1914, with power to the Executive Committee to fix the exact date. Substantial reduction was made in the price of the back Transactions of the Institute in accordance with the notice published on p. i of this Bulletin.. The By-Laws of the Montana Local Section were approved. The printing contract for the year 1914 was made with the Maple Press. Thirty-eight Members, one Associate and three Junior Members were elected.

Jan 12, 1913

By A. J. Jacobs, J. W. Spretnak, R. Speiser

The activities of nickel in liquid iron-nickel solutions containing from 10 to 90 at. pct Ni were measured over the temperature range .1510° to 1600°C. A special function was devised whereby activities can be computed by a graphical integration using the results of chemical analyses on the vapor phase alone. The liquid solutions studied exhibit negative deviation from Raoult's law, but they approach ideality as the temperature is raised from 1510° to 1600°C. The maximum heat of solution is less than -8.0 kcal per mole. The entropy of solution is less than —2.5 kcal per mole deg at 1510°C, and changes negligibly as the temperature is raised. The liquid iron-nickel solutions do not follow regular solution behavior. THE activities of the components of a liquid alloy system can be determined in favorable cases from the partial pressure of the vapor in equilibrium with the liquid alloy.' Assuming that the vapor over the alloy behaves as an ideal gas, the activity of component i is given by the expression, Where the superscripts 1, v, and o signify the liquid, the vapor, and the pure component, respectively; the f's are the fugacities, and the P's, the pressures. The quantities Pi and Pi can be determined by the

Jan 1, 1960

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By E. S. Messer

A knowledge of the magnitude of the irreducible inter.;titial water in a porous medium is so important to petroleum engineering that its determination has become routine in core analyses. The method of determination, being a production problem, should encompass the basic requirements of simplicity in technique and calculations, with reproducible results obtainable in a short interval of time. The results of the evaluation tests outlined in this report indicate that the evaporation method for determining the irreducible water is a technique which meets the requirements. The procedure consists, as the name implies. of permitting the saturant in the pore spaces to evaporate until only an irreducible volume remains. The determination of this volume can be made either graphically or by a mathematical comparison of fluid flows; the time required for each determination being dependent on the fluid used. When fluids other than those having reservoir characteristics were used, a volume factor had to be calculated which was based on the relative volume of various liquids adsorbed on grain surfaces and retained in pores. This factor made possible the calculation of an irreducible water volume when more volatile fluids such as toluene and benzene were used as the saturants. Also presented is the theoretical discussion necessary for the calculation of the capillary pressure as determined from the evaporation curve. A comparison is made between the calculated values and those obtained by experimental means. INTRODUCTION In all geological formations there exists, in the pore spaces of the rock structure, water that is held in a state of equilibrium between capillary and hydrostatic forces. "Interstitial water" is the term given to this water and is defined as that water coexisting in the pore space with the oil prior to exploitation. The term ''connate water" has often been used synonymously with this term; however, this can be true only by a specific definition since, geologically, it means the water in place at the time the rock structure was formed. The quantity of the interstitial water is a variable factor in any formation, since it depends on the hydrostatic forces present in any multiple-phase system. These forces may become unbalanced by the introduction of an extraneous force such as the raising or lowering of the "water table" or the migration of oil into a water-filled formation. Any unbalanced force results in a change in the interstitial water. There exists, however, an irreducible interstitial water. for a particular sand, that is the fraction of the pore space occupied by water when the capillary pressure at the particular point in question is at an equilibrium with the hydrostatic head of the oil sand in the reservoir. For this discussion the term "irreducible water saturation" will be used in place of "irreducible interstitial water saturation" for the sake of brevity; however, they are understood to be identical. A great amount of work has been devoted to the theory and methods for studying the irreducible water saturation and its related capillary pressure. As a result of the publications of Leverett;' Hassler, Brunner and Deahl;2 Calhoun and Lewis;3 and others, the role of capillary pressure studies is being accepted by the industry as a tool for studying suhsurface phenomena. Many techniques have been developed and published for determining the capillary pressure and irreducible water. In general, these techniques may be grouped into three classifications. One of the first was the capillary pressure method described by Leverett1 and expanded by Bruce and Welge.4 The experimental results were compared with water saturation of cores obtained using oil-base mud. Thornton and Marshall compared the irreducible water saturation of core samples determined by the capillary pressure method and by salinity and reported good agreement between the two methods. The second classification for determining the irreducible water and capillary pressure may be referred to as the "centrifugal force method." The general technique is similar to the capillary pressure method except that the force driving the reservoir fluid from the sample is of a centrifugal nature. A complete description of this method was presented by J. J. . McCullough and F. W. Albaugh.6 A process, the reverse of the capillary pressure method, was presented by W. R. Purcell.7 Mercury under pressure is driven into the pores of the rock and the saturation of the core determined at each applied pressure. The resulting capillary pressure curve is used to evaluate the irreducible water saturation. The techniques mentioned are singular in their approach to the irreducible water saturation. In all cases. an external force was applied to the core. The forces employed in the evaporation method are the vapor pressure of the liquid causing evaporation, the kinetic diffusion forces. adsorptive forces and. to a lesser degree, the viscous forces resisting flow to the surface. The basic definition of irreducible water is that water held in a state of equilibrium between capillary and hydrostatic forces This water has been described by previous investigators as being held in the microcapillaries too small to support fluid flow. Actually, this fluid volume is made up of the water in the microcapillaries and as a film adhering to the surface of the crystals. All capillaries. therefore, possess some liquid as a film, the thickness of the film being dependent on the properties of the fluid and solid. A discussion of experiments with references pertaining to the measurement of this immobile layer next to the solid surface can be found in the text by J. J. Bikerman.8 Eversole and Lahr calculated the thickness of this layer to be in the order of 10 ' to 10' cm for aqueous solutions and glass. Between two quartz surfaces they found the thickness to be 2 x 10 cm. The work of Volkova, on the capillary movement of water and toluene in quartz grains, indicated the thickness of the Immobile layers to be near 10' cm. Since any measurement is an average value, it is easy to understand that an absolute value would depend on the roughness of the surfaces involved and the complexity of the system. A calculated effective pore radius of 2 x 10 cm is obtained at the, irreducible saturation of a porous media in a water-air system when a capillary pressure of 100 psi is applied. Since the separation of the sand grains is of the same approximate magnitude as the immobile layer.

Jan 1, 1951

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.' Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.' Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general, development of the area was slow. To the south, the heavy mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.238 The axis of the syncline dips to the southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.' Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary band of secondary clays found intermittently at points across the south of the province where glacial action did not disturb or remove them.' In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.' It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1953

By James R. Stuart

AS the available remaining properties of iron ore reserves on the Mesabi Range are opened up for mining, the various properties located under lake beds are brought nearer an active status. The actual physical problems involved in stripping these properties do not act as a deterrent so much as the legal and political problems that are encountered. When it is proposed to destroy a natural lake that has been used by the public for many years, much local as well as state opposition may be encountered regarding its destruction. Public hearings must be held and some adverse publicity is likely to result. The ownership of the ore under the lake and the rights of the abutting property owners must be settled, and protection from damage caused by a disturbance in surface and subsurface drainage is likely to be demanded by property owners some distance from the proposed mine area. The Embarrass Mine, located near Biwabik, Minn., falls into this classification. A portion of the orebody lies under what was formerly Syracuse Lake, this body of water having been removed in the process of stripping the mine. An additional problem in the case of a meandered body of water is the establishment of a meander line that can be projected downward as mining progresses to form the basis for a satisfactory division between lake bed and upland ore shipments for royalty purposes. Fig. 1 illustrates the complications encountered in maintaining these divisions. A balance point was agreed upon in the center of the lake to make an equable division of lake bed ore to the abutting properties. The entire lake bed has since been adjudged the property of Minnesota. Lake Characteristics Lake bed stripping problems with which this paper is concerned necessarily are limited to a specific type of lake, namely the glacial lakes of the Lake Superior region. One characteristic common to these bodies of water is a deposit of fine black mud or silt on the bottom, frequently underlain by a layer of impervious blue clay. This is also true of the muskeg areas of the region, which present almost identical problems as lakes in stripping. The actual removal of the water and the lake bed material is a routine matter more or less standardized as to equipment, and the period of time required can be estimated easily on the basis of volume and capacity. More important than the foregoing is the execution of preliminary work, and above all, the timing involved. An account could be prepared based entirely on statistical and cost data which would give a very fair picture of the time required and cash outlay needed to effect the removal of a body of water preliminary to stripping the orebody. However, the real interest from the standpoint of the operator and the engineer who carry responsibility for completion of the job lies in the unexpected emergencies and the action of various materials involved in the stripping when the balance has been upset through diversion of water courses and the reduction of the lake level. Runoff and Drainage Lakes are located in natural basins that catch all the rain water and runoff water for a considerable area. Where a lake is involved having an inlet and outlet or a sizeable water course running through it, the drainage area may include a watershed covering many square miles. All available data then must be collected to supply a history extending over as many years for which information can be gathered on the flow of streams, annual rain and snowfall, and most important, the peak flows to be expected. Where the diversion of a stream around the stripping area is a part of the problem, this last factor is of great importance since it controls the cross-section to be selected for the diversion channel and the volume to be removed in its excavation, as well as affecting the hydraulic considerations to be met in the design of the completed channel. Characteristic material in the overburden found at the Embarrass Mine is illustrated in Fig. 2. Well Pumping Pumping from the well holes was started well in advance of the draining of the lake. Fig. 3 shows a gradual lowering of the water table with no noticeable fluctuations during the period in which the lake was being dewatered. Unfortunately, because of tight ground, a maximum flow to the wells was not maintained. This retarded the rate at which the water table was reduced so that in the course of stripping the excavation soon extended below the water table, and the great bulk of the pumping was handled from a system of sumps in the pit itself. Any dewatering program projected by prepumping from wells, a glorified well point system, would have to be started well in advance of the stripping to be of any great advantage. Preliminary drainage of the surface over the mine area is entirely apart from the actual elimination of the lake bed itself. Since the lake is what is called a perched water table because of the impervious character of the lake bottom, the adjoining surface may be dewatered below the surface of the existing lake and the flow will not be affected by the proximity of that body of water. This condition actually has been demonstrated through the establishment of a number of observation holes where a small churn drill was used to put down the holes and a 3-in. pipe was installed for taking water level

Jan 1, 1952

By J. Downie, H. A. Kendall, G. H. F. Gardner

Some cases of the motion of two miscible fluids in uniform linear models are discussed. There is no bulk flow through the models, and the convection currents are caused solely by density gradients. Horizontal, vertical and inclined positions of the models are treated separately. Analytical formulas for the motion of a narrow transition zone between the fluids are obtained and compared with measurements, and the limitations are discussed. Observations of the ultimate stabilizing effect of diffusion on the motion me compared with the theory. It is shown that fluid motion in an inclined model with a constant rate of bulk flow can be directly deduced from the cases discussed, provided the viscosity ratio is small. INTRODUCTION In some reservoirs, convection currents caused by variations in the fluid densities may be significant. For practical purposes it may be desirable either to minimize the effect, particularly in miscible displacement, or to maximize the effect as in some schemes for the production of heavy crude oils by combustion. Experiments by Craig, et al,l have shown the effectiveness of gravity in reducing the efficiency of a miscible displacement when the mixed zone between the displacing and displaced fluids is narrow compared with the height of the system. The presence of a board transition zone from one fluid to the other has been shown by Perkins, et al,2 to nullify considerably the influence of a difference in density. Indeed, the theoretical discussion given by Perrine3 has shown that when the transition zone exceeds a certain critical length the efficiency approaches 100 per cent. Many additional results 495 have been published on miscible and immiscible displacements which show the importance of density difference and also mobility ratio. The aim of the present paper is to discuss some cases of gravity segregation of miscible fluids in linear models such as are often used in the laboratory to evaluate recovery processes, and to supply additional experimental evidence in support of the conclusions. An attempt is made to calculate simply the magnitude of the fluid motion caused by density pdients and mobility ratios, and to quantify the modifications in the fluid motion produced by the combined effect of molecular and convective dispersion. However, it should be pointed out that the uniform permeability of the models and the use of only a single pair of fluids (whereas several pairs of fluids may be employed in a recovery scheme) severely restricts direct conclusions about natural reservoirs. For conciseness, the motion generated by density gradients is emphasized for the case of no bulk flow through the models. This is not a drastic limitation because, as shown in Appendix A, a fluid motion with a constant bulk flow through any linear model is equivalent to a fluid motion with no bulk flow in the same model inclined at a different angle to the horizontal, provided only that the density is a linear function of the viscosity of the fluid mixture. HORIZONTAL MODEL In this case the model is assumed to have a rectangular cross-section with a horizontal breadth b, vertical height and a great length L. Throughout.the paper it will be assumed that x-axis points along the length, the y-axis along the width and the z-axis along the height. Thus, in the present case the x, y plane is horizontal. Initially, the transition zone between the fluids is assumed to be thin and parallel to the y, z plane. An example of this situation in a practical problem arises in a scheme for using air for cushion gas in the storage of fuel gas in aquifers. 6 With the passage of time the denser fluid sinks and spreads along the bottom of the model while the lighter fluid rises. The interface extends from the top plane of the model to the bottom. Experiments have shown that for practical purposes this interface may be treated as a plane surface at all times. The surface is significantly curved, however, for viscosity ratios greater than about 10. Other complications arise with large viscosity ratios because of the nonlinear dependence of the viscosity on the composition of the mixture, so that the simple results given here are restricted to fairly low viscosity ratios.

By J. J. Frawley, W. J. Childs

Experiments were carried out to induce grain refinement during solidification by applying vibrational energy (freq 20 kc) to small specimens of bismuth, tin, and bismuth-tin alloys. The results show that if the intensity of the applied sound -field is not great enough to fragment the growing dendrites of a pure metal, no grain refinement is observed and the pain size of the dynamically nucleated specimens is the same as the grain size of a specimen statically supercooled the same amount. Bismuth specimens did not show any grain refinement; whereas, the tin specimens did show grain refinement. This phenomenon is the result of the difference in growth habit between the bismuth and tin dendrites. The bismuth-tin alloys showed grain refinement and, in addition, the segregation pattern was changed. THE solidification process is a change in phase requiring the nucleation of the solid phase from the liquid and the growth of this solid phase at the expense of the liquid phase. Since many physical properties and also the integrity of a casting are dependent on the solidification process, understanding and controlling this process are very important.' A good example in the controlling of a cast structure using heterogeneous nucleation theory is the reduction of grain size in aluminum castings by nucleation catalysis.2 This mechanism of nucleation catalysis has been explained by Turnbull.3 Another technique for grain refinement, which has received much attention but the mechanism has not been fully understood, is to vibrate the solidifying melt. Vibrations can be applied to the melt either by vibrating the mold directly or by introducing a vibrating rod into the melt.4-13 Three mechanisms have been proposed to explain this phenomenon: 1) The mechanical fragmentation of the original dendrites that grew into the melt. These crystals or fragmented dendrites act as new growth sites. 2) The nucleation of new grains in the liquid by the generation of very high pressure pulses caused by cavitation in the liquid. 3) The remelting of the dendrite arms during the solidification process. This mechanism is operative only in alloy systems and would be enhanced by stirring or mechanical vibration. The purpose of this investigation was to determine the mechanism that will increase the number of grains when mechanical energy is introduced into a solidifying melt. APPARATUS The unit used to generate the ultrasonic vibrations was manufactured by the Redford Co., and is similar to the one used in ultrasonic soldering. Fig. 1 is a sketch of the major components used for generating ultrasonic vibrations. The crystal transducer assembly consisted of four lead zirconate ti-tanate piezoelectric crystals in an aluminum holder. An acoustical horn, which was fabricated from stainless steel, was attached to the holder by a set screw. The resonant frequency of this unit was 20,000 cycles per sec. A Pyrex crucible, 4 in. in diam and 4 in. high, was contained in a hole in the top of the horn. The piezoelectric crystals changed volume when excited by an electric signal, thereby generating a sound signal which passed through the horn. The crucible was coupled to the horn by a liquid silicone oil. The purpose of the couplant was to transmit the soundwaves from the horn to the crucible. Without the couplant, much of the sound energy would be lost. The energy transmitted was sufficient at the resonant frequency used, so that acoustical cavitation always occurred in the molten metal. The presence of acoustical cavitation was detected by the characteristic hissing sound emitted from the liquid. EXPERIMENTAL PROCEDURE The influence of ultrasonic vibration on the grain refinement of bismuth, tin, and bismuth-tin alloys was studied. These metals were chosen because of their low melting temperature and the relative ease with which they can be thermally supercooled. The following procedure was used for obtaining large amounts of supercooling. Pure bismuth (99.999+), which was received in bar form, was mechanically broken into pieces small enough to be accommodated in a 50 ml beaker. About 200 to 300 g of bismuth and a few grams of SnCl2 as a flux were placed in the 50 ml beaker and melted by induction heating. The melt was held for 20 min at

Jan 1, 1970

By H. C. H. Darley

The influence of particle size and concentration on the development of chip hold-down pressure (CHDP) was studied in an apparatus designed to measure the change of filtration rate during the first second of the filtration process. CHDP is controlled by the "bridging" particles (i.e., particles in the 50 to 0.2 micron range), whereas filter loss is controlled by the colloid fraction. The results indicated that a fast drilling fluid with a low filter loss could be obtained if the concentration of bridging solids and the viscosity were kept very low. A novel group of drilling fluids, which we have named colloid emulsions, was developed to meet the above requirements. These colloid emulsions are made by dispersing art oleophilic colloid in oil and emulsifying about 5 per cent of this dispersion in water or a dense brine. Good results have been obtained in field trials with emulsions which use asphalt as the oleophilic colloid. INTRODUCTION In recent years it has been found that fast rates of penetration can be maintained in hard formations by using "clear" water as a drilling fluid. In some cases, however, water cannot be used because the very high down-hole filter loss creates various difficulties in drilling, in logging, or in producing the well. It then becomes necessary to "mud up", which results in a decrease in drilling rate. The reason that mud decreases drilling rates is a complex subject which has been well covered by such authors as Garnier and van Lingen, Cunningham and Eenink,' and van Lingen.3 One of the principal factors involved is the tendency of the drilling fluid to develop a filter cake on the bottom of the hole. The pressure differential which develops across this filter cake opposes the action of the bit in dislodging chips from the rock. This pressure differential is referred to by Garnier and van Lingen' as the chip hold-down pressure, which is denoted by the initials CHDP in this paper. The work described in this paper was undertaken to develop a drilling fluid which would minimize CHDP but which would still have a low filter loss—in other words, a fluid which would deposit a filter cake on the sides but would lay little or no filter cake on the bottom of the hole. EVALUATION OF CHDP EXPERIMENTAL Conditions governing the growth of filter cake on the sides of the hole are obviously different from those on the bottom of the hole. On the sides of the hole, cake will form continuously but at a decreasing rate, until eventually the rate of growth will equal the rate of cake erosion by the mud stream.' On the bottom of the hole, each time a bit tooth dislodges a chip the cake is removed, a fresh rock surface is exposed, and the filtration process must start over again. Thus the CHDP is determined by the amount of cake which can form in the interval between successive tooth strikes at a particular spot, normally a fraction of a second. Our first step therefore was to study filtration rates over the first second or so of the filtration process. These tests were conducted in the simple type of dynamic filter cell shown in Figs. 1 and 2. In this cell the mud was filtered through a train of rock cores while rotating blades kept the mud flowing over the surface of the core. The procedure was to evacuate the cores to 0.05 mm of mercury, saturate with brine, and assemble in the holder under brine. The permeability of the core train was then determined. A plastic seal was placed on the face of the core train, and a rip cord was attached from the seal to one of the blades. At the start of the test, 500 psi was applied to the mud, and the meniscus in the capillary measuring tube was adjusted to zero. When the blades were started, t,he seal was ripped from the face of the core, and filtration began. The filtration rate was at first measured by photographing the advance of the meniscus in the capillary tube. Using

Jan 1, 1966

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947

By P. H. Cardwell

The effect of various plastics upon the permeability of a sand and the mechanism of their ensuring permeability within the consolidated sand body is discussed. Data are presented on various properties of the plastic materials used in sand consolidation and the effect of temperature and usable temperature ranges are considered. The recovery of petroleum from uncon-solidated sands presents serious production problems, owing to sloughing of the formation. The solution of some of these problems usually has been by mechanical methods.' The ideal way of controlling the sloughing tendencies of these un consolidated formations, however, is to prevent the movement of the individual sand grains by the use of a bonding medium. A step in the desired direction was taken by Irons and Stcesser2 when they taught the use of liquid plastics to produce a consolidating deposit that prevents sloughing. More recently, Wrightsman and Buckley3 proposed a modification of this process. In this use of the liquid plastic, the sand grains become coated and the ensuing hardening of the plastic by polymerization or condensation cements together the sand Particles. Liquid plastics that have been suggested for this Purpose are of the following types: phenolformaldehyde, alkyd resins, vinyl type resins, polystyrene and the acrylic esters. When the flow of fluids through a sand must not be materially reduced, it is essential only to cement together the sand grains with liquid plastic and leave a portion of the interstitial space for fluid flow. TO be assured of obtaining fluid flow through the sand interstices after injection of plastic, it has been necessary in the past to remove the excess plastic from the interstices between the particles before it sets. Wrightsman and Buckley suggest two methods for the removal of the excess plastic from the interstices of the sand: (I) to flush the excess plastic back into the formation, away from the well bore, by use of oil or water; (2) to produce the well before the plastic has set, thereby moving the excess plastic into the well bore. Under certain well conditions it is very difficult to remove the excess plastic from all parts of the formation by either of these methods and leave the formation consolidated with no sections completely sealed. The method* described herein of retaining permeability within a sand body is to use a liquid plastic that upon setting ensures permeability within the consolidated sand body. This cements the sand grains but obviates the need for removing plastic from the interstices of the sand. One of the ways of accomplishing this is to use a liquid plastic that occupies a considerably greater volume than the solidified resin it yields on further polymerization or condensation in situ. In order to be satisfactory, the volume of the plastic while liquid should be at least one and one half times the volume of the solid formed. Preferably,

Jan 1, 1947

At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute, He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account in ledger form of all such back numbers. He shall on the first day of January of each year submit to the Library Committee a statement of the number of copies of Transactions, magazines and other publications printed during the preceding year, giving the number distributed and remaining undistributed; also a statement covering additions to and withdrawals from the total stock of Institute publications, with the number remaining on hand at date of statement.

Jan 1, 1928

I. PRESIDING OFFICER, At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President, 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6, Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute, He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute, The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account in ledger form of all such back numbers, He shall on the first day of January of each year submit to the Library Committee a statement of the number of copies of Transactions, magazines and other publications printed during the preceding year, giving the number distributed and remaining undistributed; also a statement covering additions to and withdrawals from the total stock of Institute publications, with the number 'remaining on hand at date of statement,

Jan 1, 1928

By Gordon M. Yocom

A PROPER consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modern methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that

Jan 1, 1941

By R. H. Brown, F. Keller

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By Morris Muskat, J. M. McDowell

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By J. M. McDowell, Morris Muskat

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949