Search Documents

By G. Sachs, G. Espey

SIMPLE methods can be used for the determination of the residual stresses in thin-walled tubing if the stresses consist of high tensile stresses at the one surface and high compressive stresses at the other surface Such a stress distribution is approximated in sunk tubing and in deep-drawn shells It is possible to cut sections from such articles in such a manner that a major part of the residual stress is relieved by a bending of the part that is separated from the adjacent metal The circumferential stress is evaluated from the change in diameter D, occurring on splitting a length of tubing (Fig Ib),1-5 or from deflection resulting from the cutting out of a circumferential tongue (Fig Ia) G The bending moment M released by such a flexure is [ ] The release of this bending moment corresponds to the release of stresses, which, in a thin section, vary linearly from one surface to the other, and have the following value in a particular fiber a certain distance (zx from the surface [ ] where C is the section modulus and d is the thickness of the section, the ratio AI C being d 2 for a rectangular section* The maximum stress values at the surfaces are [ ] For most purposes the simpler equations [ ] will be satisfactory, where Dm is the average of the mean diameters of the tubing

Jan 1, 1941

By William Plank

In practically all rock-excavation problems there is need for a careful study of the rock structure, its fault, cleavage or bedding planes, and even the texture of the rock itself. These studies should form the bases upon which an excavation method is selected and they should be carefully considered in predicting the amount and extent of the excavation. The need for such studies was forcibly illustrated in the problems involved in a cut made in 1929, along and underneath a 200-ft. high rock projection for a State-highway near the City of Easton, Pennsylvania. The rock mass was badly faulted and also contained a number of cleavage planes at approximately right angles to the fault planes. Much of this structure was visible and could have been studied and analyzed before' the work was begun. The State had rigid specifications as to finished grade and slope of cut, which apparently were made without reference to the geologic structure. The contractor complied with the specifications, under the close inspection of the State engineers. A tunnel blast was, placed in the base of the cliff, with the result that 65 per cent more rock was broken than was intended by the specifications. About four years after the blast, the writers of this paper studied the circumstances surrounding the operation, to determine the cause of this excess excavation.

Jan 1, 1935

By Gunnar Thaning, Goran Mathisson

The iron ores mined by LKAB in the north of Sweden have excellent beneficiation properties. This gives LKAB a favorable position as regards the production of low silica pellets for direct reduction. LKAB has concentrated on developing and marketing grades of pellets for the Midrex-Purofer-HyL process group, i. e., such direct reduction processes carried out in a shaft furnace or a static bed using reformed natural gas as a reducing agent. The paper deals with properties and quality demands of iron ore pellets for such processes. Matters such as the effect of the residual magnetite in the fired pellets on the degree of metallization, the amount and composition of the slag phase in the pellets, the mechanism of the disintegration during reduction, the state of swelling of the pellets during the conditions prevailing in these processes, the importance of the porosity, the improvement of the reducibility and lowering of the sticking tendency of the pellets by small additions of suitable additives, and the influence of the pellet size are discussed. A special test procedure for direct reduction pellets has been elaborated by LKAB. Thus, three metallurgical properties are routinely determined separately, namely reducibility, reduction strength, and sticking. The test methods are described. Finally the present and future LKAB pellets for direct reduction are presented with respect to chemical analyses and metallurgical properties.

Jan 1, 1980

By Jack Haptonstall

INTRODUCTION The mines of western central Mexico historically contributed a profusion of gold and silver for the treasury of Spain and later provided sources for financing the Mexican War for Independence and the Mexican Revolution. The western coastal and barranca (cliff) tribes were hunters and extremely hostile, and the Spaniards were not able to penetrate many of the rich districts of their rugged homeland until the mid-1700's. This was more than 200 years after Cortez began the Inquisition by defeating the Aztecs and their allies in a decisive battle in the great city of Tenochtitlan (present day Mexico City). The Spaniards had a voracious appetite for silver and gold, and it was inevitable that they would finally subdue the natives and commence mining activities. Described in this paper are some of the precious metal mining activities in the southern half of the State of Sinaloa and the western half of the State of Durango (Figure l), and specifically those mining activities in the area controlled by the company with which the author was associated for 14 years, Minas de San Luis, S. A. de C. V., the parent company of which is now Industrias Luis Min, S. A. GENERAL DESCRIPTION Geography, Logistics and Climate The most spectacular of the physiographic provinces, the western Sierra Madre Occidental is the cliff or "barranca" province, the

Jan 1, 1983

By R. HAYDEN, H. B. HALLOWELL, H. O. Hofman

THE object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe in his classical paper "Contributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks.2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker' and Addicks.4 The absorption of gases has received' attention by Hampe,5 Stahl 6 and Heyn.7 The effects of casting-temperature have been noted by Stahl.8

Mar 1, 1907

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By AIME AIME

THE Fall Meetings of the Institute of Metals Division and of the Iron and Steel Division were held in Cleveland from Tuesday, Oct. 20, to Thursday, Oct. 22, as a part of the National Metal Congress. The registration at the technical sessions was something over 450 and the attendance at the joint dinner of the two Divisions on Wednesday evening taxed the capacity of the dining room. The president of the British Institute of Metals, W. R. Barclay, consulting metallurgist to the Mond Nickel Co., Ltd.; of London, was in attendance at several of the technical sessions and was one of the after-dinner speakers at the banquet. He commented on the desirability of greater international amity and cooperation in these troubled times and of the role that technical societies, such as the A. I. M. E. and his own British Institute of Metals, can and indeed are playing in bringing this to pass, with their membership and contacts reaching to all parts of the world. He also referred to the new reciprocal membership arrangements in effect between the A.I.M.E. and the British Institute of Metals.

Jan 1, 1936

By Edmond S. Miksch

The morphology and growth rate of ice grown in supercooled water are markedly affected by convection of the water. A dendritic ice sheet with water flowing past the dendrite tip exhibits deflection of the dendrite spine toward the upstream direction, accelerated growth of secondary spines on the upstream side, and suppression 01" secondaries on the downstream side. Flow causes a thin disk to become corrugated, the corrugations being parallel to the flow. Flow causes an increase in the growth rate of the ice. IF a small seed of ice is placed in slightly supercooled water, it grows initially as a disk with the axis of the disk parallel to the c axis of the ice crystal.' It appears that growth in the c direction is inhibited, while growth occurs with equal facility in all directions in the basal plane. It appears that growth rate as a function of interface temperature is very nearly equal for all directions similarly oriented relative to the c axis. Subsequent to the discoid growth, branching occurs and dendrites develop. The primary dendrite spines grow parallel to the six equivalent a axes of the crystal. Secondary, and in some cases, tertiary spines also grow in these directions. The highly anisotropic: dendritic growth indicates that there must be some finite difference of growth rate for different directions in the basal plane. These differences must be quite small, however, since if they were large, the discoid mode would not occur. Hence, it was expected that the dendrite growth direction could be deflected from the crystallographic direction by perturbation of the thermal field at the dendrite tip. Experiments were done in which perturbation of the thermal field was accomplished by causing the supercooled water to flow past the dendrite tip. The flow direction was perpendicular to the c axis of the crystal, and was perpendicular to the primary spine of the unperturbed crystal. Supercooled water was supplied by a 15 cm cubical copper box, which was refrigerated and insulated so it could cool water to temperatures down to —2oC, and maintain the temperature constant to O.l°C for the duration of a run. A lucite channel of rectangular cross-section, 12 by 24 mm, was mounted horizontally in the box, with one end open so water could flow into it, and the other end leading out through the wall of the box to a length of tubing leading: to an orifice plate 123 cm below. cnunMn s MIKSCH, MemberAiMe, formerly Research Associate, Research Associate, Fig. l(b)—Vertical section of apparatus A horizontal cross-section is shown in Fig. l(a), and a vertical section is shown in Fig. l(b). Means for observing the ice are shown in Fig. l(a). Collimated light passes through the ice sheet and forms an image on the ground glass screen. A lucite box containing dry air was employed to prevent condensation. Ice of the desired orientation was provided by the seed holder shown in Fig. l(b). This device was made of lucite, and had a reservoir in which ice could be frozen by placing it in a freezer. This reservoir com-unicated with the outside only through a narrow gap between two sheets of lucite. The seed holder (after ice had been washed off its exterior) was immersed in the tank of supercooled water, the narrow gap terminating in a slot in the top of the flow channel. Ice growing through a thin water layer in the gap between the two sheets of lucite was oriented so its c axis was perpendicular to the sheets. This orientation is an application of a growth phenomenon2 which causes ice growing along a smooth solid surface in supercooled water to orient itself so its c axis is normal to the surface. After the ice grew into the channel, further orientation was necessary, since the direction of the a axis

Jan 1, 1970

By Donald L. Katz

The compressing of gas into a partially depleted gas drive oil reservoir to bring the contents to a single phase miscible with gas is proposed as a process worthy of serious study. The compressed gas and vaporized oil would be recovered by cycling. This paper explores the Possibility of recovering oil from reservoirs of 6,000 ft or more by this method. INTRODUCTION Many new methods for increasing the recovery of oil from reservoirs are under consideration in the various research laboratories. One method which should be considered for recovering oil From partially depleted gas drive fields is to compress gas into the reservoir until the contents become a single phase miscible with more gas. Natural gas then may be cycled through the reservoir to recover the oil. This procedure ideally will eliminate the capillary effects of the liquid ill the porous media and should permit recoveries similar to those obtained in cycling operations, probably of the order of 80 per cent. This paper explores the information now available for the prediction of the performance of such a project and discusses the problems likely to be encountered in recovering oil by cycling. For many years dry natural gas has been passed through oil reservoirs to recover natural gasoline which would vaporize from the oil. Recently a process of recovering more of the high boiling hydrocarbons has been described by employing high pressures at which the heavier hydrocarbons have a higher volatility. Nevertheless. this reported method does not eliminate the differential nature of the vaporization process and capillary forces are still present in the reservoir. The process under discussion in this paper would minimize differential vaporization and would remove capillary forces which are responsible for low oil recoveries. Higher gas pressures are required to accomplish this removal of the miniscus, but it does not follow that more gas is required for oil recovery. The process is limited to reservoirs deep enough to permit the use of the required pressure — Probabably 6,000 it and deeper. DESCRIPTION OF THE PROCESS Briefly, the process is to compress natural gas into an oil reservoir which is partially depleted so that it has an oil saturation in the range of 40 to 60 per cent of the hydrocarbon pore space. The injected gas will pass through the channels formerly carrying gas to the wells to build up the pressure and dissolve in the oil phase. This injection will continue without production from the field until the reservoir reaches a single phase. If one were to select unique conditions such that the gas composition, the reservoir oil composition and the Per cent saturation would bring the mixture in the reservoir to the critical temperature and pressure simultaneously the phase behavior accompanying injection is shown by Fig. 1. The oil-gas mixture in the depleted reservoir has a critical temperature at C,. Addition of natural gas to the mixture will give a new critical temperature for each addition. Mixture No. 3 is shown to have its critical temperature at the reservoir temperature and reservoir pressure at P: the critical pressure. Under ideal behavior, the entire reservoir would be at iti critical temperature and pressure and the entire hydrocarbon content would be at a single phase. If the reservoir content were a binary system of methane and a heavy constituent. it would be miscible with more methane. However, for complex mixtures the critical locus does not confine the two phase region, and the dew point curves of Fig. 1 occur above the critical locus. If fluid which was injected into the rezervoir at the critical point were of the

Jan 1, 1952

By Donald E. Garrett

The processing of brines from Searles Lake, California, yields one of the world's largest supplies of borax and boron chemicals, second probably only to the massive deposit at Boron, California. Two companies produce from this deposit, the American Potash & Chemical Corp. and the West End Chemical Co., a division of the Stauffer Chemical Co. Two processes are employed in recovering borax from the brines; one is used by both companies and consists of carbonating the brine to form sodium bicarbonate, removing this, and then cooling the liquor to crystallize a crop of borax. Only American Potash uses the second process, evaporating the brine to concentrate it and remove (crystallize) much of its NaCl, Na2CO3, Na2SO4, and NaLi2PO4 content, quick cooling the remaining liquor to remove KCI, and then seeding the filtrate to remove borax. Both methods will be briefly described. Searles Lake is a large evaporite body formed during the most recent two Sierra Nevada ice stages, the Tahoe and the Tioga. Runoff waters from the Sierra Nevada Mountains collected in the large Owens Valley drainage basin and from there overflowed into the Indian Wells basin and then into Searles Lake. In each Lake, evaporation took place. To a large extent the Owens and Indian Wells lakes acted as settling basins, for much of the mud, and insoluble calcium and magnesium precipitates were deposited there. Recent volcanic activity in the mountains to the north and east of Owens Lake had scattered considerable mineral-rich volcanic ash and debris throughout the drainage area, and several hot springs were formed that contained boron and other salts. The present flow rate and concentration of several springs, and the known age of at least the Tioga zone, can fairly well account for all of the boron present in Owens and Searles Lakes.1 The tungsten content can be accounted for in a similar manner.2 Most of the salts thus originally present in the fresh water runoff-from ice, snow, and rain-accompanying these two ice stages were ultimately deposited in Searles Lake. During the Tahoe period, from 25 to 40 ft of massive, mixed salts were deposited, along with six interspersed layers of mud (four inches to two feet thick) representing comparatively brief interglacial periods. Before the final desiccation of the lake, from 10 to 14 ft of new mud was deposited, representing the Tioga stage. The crystals subsequently deposited were from 70 to 90 ft thick, and form the present lake surface. The extent of the salt body is about 34 square miles, of which 12 square miles are exposed salt; the remaining area is covered by recent alluvial deposits (chiefly mud). The present lake is generally dry on the surface but floods to a shallow depth following heavy rains. The crystal body of both zones consists of continuous clusters of salts, and the voids between crystals (about 45 pct of the total volume) are occupied by brine. The level of this brine never recedes more than several inches below the salt surface. The brine pumped to the plants for processing is generally saturated with all of the solid phases present in that area, and thus is a complex mixture containing about 35 pct solids (see Table 3). The brine composition varies somewhat at different areas of the lake and from upper to lower structures, so wells are drilled in the areas and to the depths desired. A casing is cemented in the hole to within a short distance from the bottom, and pumps with about 14-ft suctions are mounted on the casing to pump the brine into the plants. The evaporation process of the American Potash & Chemical Corp. treats upper structure brine, evaporating all of the water from

Jan 1, 1960

By J. J. Taber, W. K. Meyer

Experiments on consolidated sandstones have shown that a variety of conditions are responsible for the wide range of behavior observed when oil and water are displaced simultaneously by a solvent which is miscible with both. The type of displacement is influenced most strongly by the relation between the plait point of the ternary phase diagram and the composition path followed by the system as it achieves mis-cibility. Neglecting viscosity, the displacement becomes less efficient as the distance between the composition path and plait point is increased in either direction so that a very wide spectrum of displacements is possible with different alcohol, oil and brine systems. It is possible by choosing various composition paths as miscibility is achieved to exercise some control over the actual displacement mechanism. Control over the composition path is exercised by adding oil or water in specific amounts to the alcohol prior to its injection into the porous medium. This technique apparently makes it possible to obtain piston-like displacements with systems which are usually characterized by the efficient displacement of only one of the two phases i.e., either oil or water, while the other phase lags behind. However, the simultaneous displacement of oil and water is not as efficient as other miscible displacements at a similar mobility ratio. The evidence indicates that both oil and water "leak" into the alcohol "piston" in compensating amounts. With oils of low viscosities the displacement is inefficient because the low oil saturation in the stabilized bank causes oil to be trapped by water before miscibility is attained. INTRODUCTION The simultaneous displacement of oil and water by solvents such as alcohol has been investigated in the laboratory and in the field. The laboratorv workers investigating all-liquid miscible systems have recognized the great importance that the nature of the traingular phase diagram exerts on the efficiency of the miscible displacement. Gatlin and Slobod pointed out that displacement efficiency will be improved if miscibility can be retained for long periods and that this behavior tends to be followed if the applicable phase diagrams have very low binodal curves. In their unconsolidated sand tests the alcohol was considered an ideal miscible piston displacing both oil and water phases. Later workers have pointed out that an important feature of the phase diagram as far as oil recovery is concerned is the location of the plait point. This is particularly true in the case of consolidated Sandstone.3 Since the original discussion of this effect, the importance of plait-point location has been confirmed and discussed by other author The early workers394 recognized that the position of the plait point could be altered by changing the oil or the alcohol used in an experiment. In addition, recent work has demonstrated that the plait point can be shifted by altering the nature and concentration of dissolved salts in the aqueous phase. However, the entire scope of the relationship between displacement and plait point has not been discussed previously and a technique for changing the composition path as miscibility is achieved in a particular ternary system, i.e., oil, water and solvent, has not been demonstrated. * The importance of oil viscosity on the efficiency of oil displacement by alcohol has not previously been observed, probably because the range of viscosities used in earlier experiments was too restricted. It is the object of this paper to describe the relationships between the ternary phase diagram, fluid properties and the displacement achieved. A technique for controlling the nature of the displacement is also presented. THEORY AND DEFINITIONS PISTON-LIKE THEORY The theory of alcohol flooding has been discussed in some detail.2-4 The concept was advanced that

Jan 1, 1965

INTRODUCTION The meaning of cash flow has already been defined as after-tax earnings available for use by the corporation or business. It is therefore apparent that a significant part of mineral economic evaluation is concerned with correct and accurate computation of taxable income under existing tax laws, and the proper treatment of tax allowances and deductions. The various methods of depreciation, depletion, and amortization are all means whereby the investor can earn back or recover, before taxes are imposed, the investments made for purposes of doing business or for the production of income. Each of these three types of tax deduction are applied to different investment items such as property, equipment, buildings, research, etc. The cost of buildings, equipment, machinery, and transportation equipment are representative of capitalized business costs that must be recovered by depreciation over the life of the asset. The property investment costs of acquiring natural resources such as minerals, oil and gas, and standing timber are examples of investment costs that may be recovered by depletion. Several other capitalized business costs, such as research expenses and trademark expenses, may be recovered by amortization. The term "capitalized" means that the in- vestment cost is not deducted as an operating expense in the year that it is incurred, but is spread out over a period of years through depreciation, depletion, or amortization deductions according to lawful schedules. Of course, any capitalized cost can only be deducted once. The other costs of doing business which are not capitalized, such as labor and operating costs, are said to be "expensed," i.e., they are written off for tax purposes in the year they occur. DEPRECIATION Depreciation, according to US tax law, is a deduction from taxable income permitted as a "reasonable allowance for the exhaustion, wear and tear of property out of its use or employment in a business." The original cost of the property is the usual basis for determining depreciation. Since depreciation write-off is applied over the useful life of the asset, the first step is to determine the estimated useful life or its allowable depreciable life. These two lives may or may not be the same. No average life is applicable to all types of depreciable assets under different conditions or in different types of business. It is the taxpayer's responsibility to determine the useful life of the asset according to his own operating conditions and experience, within the guidelines set by the US Internal Revenue Service (IRS). The Class Life Depreciation Range (ADR) System permits the taxpayer to choose from a range of depreciable lives at 20% below or above the present guideline life. The second step required in calculating depreciation is to determine an estimated salvage value for the asset. The salvage value is an estimate, made at the time of acquisition, of the amount of money which can be realized by the sale of the asset at the end of its useful life. The four depreciation methods most widely used in the US are: (1) the straight-line method, (2) the declining balance method (double declining balance), (3) sum of the years - digits method, and (4) units of production method. Straight-Line Depreciation Method The straight-line depreciation method is the simplest for calculating depreciation. The depreciation for each year is determined by subtracting the estimated salvage value from the first cost of the asset and dividing the result by the years of life. The method gives equal annual deduction over the depreciable life. Salvage value equal to or less than 10% of the first cost may be ignored. [first cost - salvage Straight line = years of life ] Declining Balance Depreciation Method Declining balance depreciation, or double declining balance (DDB) as most frequently applied, is used for accelerating depreciation in the early years of the asset and is the fastest depreciation method allowed by the US Internal Revenue Service. The declining balance

Jan 1, 1980

By W. W. Mullins

The development, by the mechanism of volume diffusion, of a grain boundary groove on an interface separating a solid phase and a saturated fluid phase is calculated under the following assumptions: 1) isotropy of the interfacial free energy 's, 2) applicability of the Gibbs-Thompson formula relating curvature and chemical potential, 3) a nearly planar groove surface. The groove profile is found to have a .fixed shape and linear dimensions that are proportional to (time)1/3. The constant of proportionality is evaluated and involves ?s in such a way that the latter my be evaluated from grooving kinetics. A grain boundary that intersects an interphase interface will tend to produce a groove along the line of intersection (Fig. 1). The ultimate motivation for the formation of the groove is the reduction in interfacial free energ that occurs as the grain boundary contracts. Smith has discussed the way in which the free energy of the interfaces determines their dihedral angles at the groove root and has given a detailed analysis of the effect of the dihedral angles upon the nature the microstructures developed in polyphase alloys. Herring2 has extended the considerations to the case in which the free energy of an interface depends on its orientation and has thus added torque terms to the condition for interface equilibrium. Although the grain boundary and the interphase interface may quickly achieve the proper equilibrium angles where they intersect, as determined by the balance of equivalent tensions and torques,"2 the groove will generally continue to grow (though with decreasing speed). Thermodynamically, this continued growth reflects the fact that the lowest free energy cannot be achieved until the entire grain boundary has been eliminated; mechanistically, the growth occurs in response to inhomogeneities of chemical potential that are caused by the constraint of fixed dihedral angles at the groove root. The latter point is illustrated in Fig. 1, which shows that atoms* near the groove are on the convex side of a cylindrically curved surface and therefore have a higher chemical potential than atoms on the flat interface beyond. Thus atoms tend to leave the curved groove shoulders and force the groove to deepen. When both phases are solid additional chemical potential gradient may arise from whatever strain fields are necessary to insure continuity of material across the interface. In the discussion that follows, this complication due to strain will not occur since we always assume one phase to be a fluid and the other a solid. The transport processes that may operate to permit growth of the groove are surface (interface)* diffusion, volume diffusion in the phase on either side of the interface, and evaporation-condensation when one phase is gaseous. (Also a melting-freezing process is responsible for groove enlargement on a solid-melt interface as discussed in Sec. VI). The theory of grain boundary grooving has been discussed in detail for the processes of surface diffusion and of one type of evaporation-condensation.3'4 The theoretical predictions for the mechanism of surface diffusion have been confirmed in an experimental study of grooving kinetics in copper.5 In this paper, the theory of groove development by volume diffusion will be presented. Volume diffusion can occur either by atomic migration in the solid S or by diffusion of S atoms in the fluid phase, or solvent, adjacent to the groove surface. As discussed in Sec. V, volume diffusion in the solid should be less important than surface diffusion in forming a groove. Apart from verifying this statement then, the main interest of the present analysis centers on diffusion in an external solvent. The solvent may be either a liquid (e.g., water, or-

Jan 1, 1961

By T. F. Mueller, P. A. Witherspoon

For the case of an infinite radial system operating at constant terminal rate, the reservoir engineer often uses the "point source" solution of the diffiusivity equation to study pressure interference effects. At early times and at short distances from the inner boundary these solutions are invalid. The amount of error is often not precisely defined because of mathematical difficulties. Work presented here shows that, if dimensionless time is defined appropriately, previous solutions of the pressure equation can be displayed .as a family of curves on one chart. These solutions include the point source solution (referred to in the field of hydrology as the Theis solution) and other solutions obtained with digital computer methods. With these curves, an exact evaluation of the pressure drop within a reservoir or an aquifer can be made by the engineer. Examples of field problem solutions are presented. In most reservoirs the error involved when the Theis solution is employed is often negligible; whereas, in the calculation of interference effects in an aquifer, a substantial error can occur through such an approach. INTRODUCTION Flow equations are used in petroleum engineering to study the behavior of individual wells and reservoirs. In the case of wells, the pressure response at the wellbore face is the major point of interest; whereas, in the case of reservoirs, the pressure response at the interface of the aquifer boundary is sought. To aid in such studies, the flow equations have been solved in terms of the behavior at these two inner boundaries. Only limited work has been published in regard to the pressure conditions away from these points, i.e., within the reservoir or aquifer. Theis and Mortada are among the few who have reported on this problem. The Theis approach employs the exponential integral and is valid for pressure conditions that occur some distance away from the flow disturbance. It is derived from the concept of a point source, as opposed to a flow across some finite area. The Mortada results, on the other hand, are valid at all points within the reservoir or aquifer. They are presented in terms of dimension less ratios of the radius where the pressure is desired to the radius where the flow rate is measured. Their main use, in the past, has been in aquifer studies. The published results are presented in the form of graphs that are limited to a maximum radius ratio of 64. These graphical results are cumbersome to interpolate at non-integral radius ratios, so that one may be forced to utilize a rather involved analytical expression presented by Mortada. BASIC EQUATIONS The solutions of Mortada and Theis are both based on the diffusivity equation as applied to the case of an infinite radial system subject to a constant terminal rate. The equation is obtained by combining the material balance equation with Darcy's flow equation. The assumptions implicit in the use of this equation are as follows: (1) a single fluid is present that occupies the entire pore volume; (2) the reservoir is horizontal, homogeneous, uniform in thickness, and of infinite radial extent; (3) compressibility and viscosity of the fluid remain constant at all pressures; and (4) fluid density obeys the equation Using the diffusivity equation in situations where the above conditions do not hold will result in errors. These errors (not discussed here) but only the errors which arise in the solution of the equation itself. The diffusivity equation for the homogeneous reservoir conditions cited above can be written in cylindrical coordinates, as To obtain a dimensionless equation, so a single solution can be used for applications of different porosity, permeability and fluid properties, the following transformations are usually made: After these transformations are made, Eq. 3 .can be written in dimensionless form, as MORTADA SOLUTION One solution of Eq. 6 has been given by Mortada.

Jan 1, 1966

By Wilfred Walker

With the advent of the New Global Tectonics a coherent pattern of geology is emerging. To the economic geologist this is of vital concern because the type of mineralization in particular environments is predictable. Developments in geological reasoning now take their place beside developments in geochemistry and geophysics. Much is known of the worldwide geography of the Alpine orogenic period because it is now ending its 200 million years of existence, starting with the Jurassic, and we can see the mid-ocean rises and the down flow zones, and between them the stable oceanic and continental platforms. The concepts of mantle cells, the spreading sea floor, and continental drift have gained general acceptance. The oceanographers have demonstrated the uprises like that in the mid-Atlantic. In this paper it is suggested that down flows in the oceans are marked by island arcs, like the West Indies; and down flows in the continents are marked by orogens like the American Cordillera. The number and position of mantle cells is controversial: a total of about 16 cells is suggested in this paper. Certain cells expand, and as they carry continents with them give rise to concepts of plate tectonics. Specific types of mineral deposits are associated with the uprises, oceanic and continental platforms, and down flows. The uprises are accompanied by the currently described Red Sea and Salton Sea deposits, the oceanic parts of the platform have the nodular deposits, and the continental platforms have the post-tectonic deposits. However, most economic metal deposits are associated with the down flow zones in which the stage of geosynclinal development controls the type of deposit: (1) In the initial development stage the simatic upper mantle may be tapped and give rise to the volcanogenic massive base metal sulfide deposits and to the ophiolite suite which characteristically carries nickel, chrome, and cupreous pyrite. (2) In the early geosynclinal stage sialic crust is driven down into the simatic magma of the upper mantle and basic to acidic differentiates give rise to stocks accompanied by skarn and hydrothermal deposits. (3) The intermediate stage of geosynclinal development gives rise to tin-tungsten, lithium, and beryllium deposits as the magma chamber rises above the level of the upper mantle and there is no simatic component. (4) The late stage is one of regenerated deposits. The porphyry deposits are not restricted to stages but only by the time of generation of acid magma. As the geosynclinal system dies, the mantle is again the source of magma, giving rise to gabbro and diabase dykes and sills: in this last, post-tectonic, continental platform environment are found the Mississippi Valley type lead-zinc deposits, the Blind River and Witwatersrand type of sedimentary uranium and gold deposits, and also Sudbury's nickel. The key relationship of major ore deposits generated by downflows is depicted herein on a framework of uprises, platforms, and downflows in the Alpine orogenic period. There is evidence for nine orogenic periods, of which the Alpine period is the latest, having taken place from 3500 million years ago to the present. Each period was characterized by its own worldwide mantle cell system and associated uprises, platforms, and down flows. The cycle of geosynclinal development, including corresponding cycles of mineralization, can be precisely defined in relation to each of these orogenic periods. The development of the Alpine orogenic period therefore can be used as a guide to the study of the earlier orogenic periods which comprise well known periods: Kenoran, Hudsonian, Grenville, and Paleozoic; and less well known: Konkian, Aulian, Belomorian, and Elsonian [(Table 1)]. Each name is used for the period as a whole, and not for the main orogenic event.

Jan 1, 1973

By R. Kerby, T. R. lngraham

The rates of cadmiuln cementation from buffered solutions were studied on both the cylindrical and circular faces of a rotating zinc disk. The activation energies are equivalent on both surfaces, but the rate is more rapid on the cylindrical face. At higher temperatures and at pH values above 6.4, the rate of deposition increases because of an increase in the cathodic area of the deposit. The rate may also be increased by decreasing the thickness of the diffusion layer by rapid stirring. The presence of small amounts of copper, cadmium, lead, iron, or aluminum in the zinc does not affect the cementation rate, but when srnall amounts of copper, cobalt, and arsenic were present in the solution cadmium deposition ceased shortly after it started. Small amounts of copper in solution become cemented with the cadmium to form a coarse deposit of Cd3Cu. When zinc ores containing cadmium are processed for electrolysis, the cadmium appears with the zinc in the leach liquors. Because of the discharge potential of the cadmium ion and the hydrogen overvoltage on metallic cadmium, the cadmium ion must be removed prior to zinc electrolysis to prevent its codeposition. Cadmium is usually removed from acidic zinc sulfate solutions by cementation on zinc. When zinc sheets are used with the appropriate conditions of pH and temperature, a finely divided, high-purity cadmium powder is obtained; it floats to the surface with attached hydrogen bubbles and, after careful washing, may be processed directly to a marketable product.' The reaction on zinc sheets is relatively slow because of the limited amount of exposed cathodic area on the sheets. A much more rapid reaction is obtained when zinc powders are stirred into the solution, but this procedure does have a potential disadvantage: some unreacted zinc may be trapped in the cemented cadmium and thus lower its grade.1 The equilibrium constant at 25°C for the displacement of cadmium by zinc is of the order of lo", which indicates that at equilibrium the displacement would be essentially quantitative and no back reaction need be considered. This indication is not entirely true, however, because in the presence of oxygen any loose cadmium which is out of contact with metallic zinc tends to redissolve after cementation.' The overall effect is much the same as that to be expected if the equilibrium constant were much smaller. Previous experimental work on cementation reac- tions3 is in general agreement that the rates of cementation usually follow first-order kinetics. The metal on which cementation occurs is considered to consist of anodic areas from which metal dissolves and cathodic areas onto which the reactive metal is cemented. For the reaction to continue, the cemented deposit must remain open and porous for the removal of ions. Usually, the deposited metal influences the rate of cementation; when it blocks the pores in the deposit, the rate of cementation will be decreased. Alternatively, when the cemented metal grows as den-drites or as coarse powder the cathodic area is correspondingly increased and the rate of cementation increases,3 Thus, it is only during the initial stages of cementation, prior to the development of deposit effects, that the kinetic behavior of the reaction may be studied without ambiguity. In this paper, experiments will be described for cementation of cadmium from dilute solutions onto the surface of a rapidly spinning zinc cylinder. The effects of ionic concentration, disk rotation speed, temperature, and impurities will be described. APPARATUS AND PROCEDURE The apparatus used for the experiments was described in a previous paper.4 It consisted of a 2-liter vessel in which the contents were protected, against oxidation, by a stream of prepurified nitrogen. The vessel was immersed in a water bath which controlled

Jan 1, 1970

By G. R. St. Pierre, M. J. Pool, R. Speiser

The activities of chromium in solid Cr-Ti solulions contaitning from 10 to 90 at, pct Cr were measured over the temperatutre range 1250" to 1380°C. The Knzudsen effusion technique with direct weighing of the Knudsen cell was used. This was possible because the vapor pressure 0f chromium is about 600 times greater than the capor pressure of titanium so that the amount 0f titanium effusing could be neg-Lected. the activities of titanium were determined by g-raphical integration of the Gibbs-Duhertz equatiotz. The solutio~ls sllcdied exhibited positive deviations from Raoult's law, but they approached ideality as the temperature was raised from 125 to 138t C. The integral free energy of mixing was calclated from the activity values. AF has a maximum value of - 1.66 kcal a1 1390°C and a composition oj 55 at. pcl Cv. The free energy of formation of 'TiCr, is —0.76' lzcal a1 1250°C. The heats and entropies of mixing usere determined using the second law and thus tile mlues could be in error by a considerable amount. The Cv-Ti system is not a regular solution. ThE increasing emphasis on application of various models to alloy formation and solution behavior has led to an intensified interest in the thermochemistry of alloys. In a majority of the cases where different models have been applied the alloy system used was a simple one. However, the amount of data available on more complicated systems is small and in order to fully understand the behavior of metallic solutions more experimental work has to be carried out on these systems. The Cr-Ti system is reasonably complex and even though this system was being investigated as early as 1937 by Kroll,' no previous work has been done on the thermodynamic properties of either the liquid or solid state. This research was undertaken to determine the thermodynamic properties of solid Cr-Ti alloys. EXPERIMENTAL PROCEDURE The experiments on the Cr-Ti system were carried out in a water-cooled metal vacuum system. This system is composed of a brass vaporization chamber wound with copper tubing for cooling purposes, a brass liquid-nitrogen trap, an oil diffusion pump, and a Duo-Seal forepump. The pressure in the system is measured with an ionization gage. The interior of the vaporization chamber is shown schematically in Fig. 1. The Knudsen cell is supported by the molybdenum tripod, and a magnetically operated shutter is provided to protect the Pyrex sighting glass against deposition of metallic vapors in the intervals between temperature measurements. Heating is accomplished by means of a 20-kw 450-kc Westinghouse oscillator. The susceptor in this case is 10-mil tantalum seamless tubing which also forms the outside of the sample container. The remainder of the sample container consists Of an im~ervims re-crystallized alumina crucible and a 10-mil-thick tantalum lid. Two holes are drilled in the lid. The diameters of these holes were measured with the calibrated stage of a "Tukon" microhardness tester. The thicknesses were measured with a micrometer. A Leeds and Northrup disappear ing-filament optical pyrometer was used to measure the temperature. This is sighted through the smaller of the two holes in the lid and corrections for the emissivity of the sample were not necessary since the ratio bf cell length to hole diameter was large enough to insure a hohlraum. The pyrometer was calibrated at the ~~t~~~l Bureau of Standards, and the correction for the Pyrex sighting window was determined in the laboratory. The titanium used in this investigation was obtained from Mallory-Sharon and the chromium from The Union Carbide Metals Co. The reported purities were

Jan 1, 1968

By G. Derge, Ling Yang, John Henderson

Self-diffusion coefficients of aluminum have been measured by the capillary reservoir technique in liquids of the CaO-SiO2-Al2O3 system containirg equimolar portions of CaO and SiO2, in the temperature range 1400o to 1520oC. For the melt containing 6.0 mole pct Al2O3 the results can be expressed by the equation D = [(4.3 * 0.3) x 104] exp [(-85,000 * 17,500)/RT]cm~sec-'; for the melt containing 12.5 mole pct Al2O3, by the equation D = (5.4 i 0.2) exp [(-60,000 * 10,00O)/RT] cm2sec-: A concept of the constitution of these melts has been developed which proposes that the ratios O/(Si +Al) and Al2 O3/CaO determine the dominant species present. In recent years considerable work has been done on the system CaO-SiO2-A12O3 with a view to elucidating the structure of liquids of this system. Conductivity,' electromotive force, 3 density,4 and activity5 measurements have all contributed to an understanding of the problem, but as yet there is no entirely satisfactory theory that can account for all the observed experimental results. In principle, measurements of self-diffusion coefficients should give further information which is not obtainable in other ways. Self-diffusion coefficients for calcium, silicon,6 and oxygen7 have been measured. The present investigation extends the series of self-diffusion coefficient measurements to include aluminum and develops a concept of constitution for liquids of this system which is compatible with all the observed experimental results. EXPERIMENTAL The technique used in the measurement of the self-diffusion coefficient of aluminum was the capillary-reservoir method,8 A126 being incorporated in the melt contained in the capillary and inactive aluminum in the reservoir melt. This method was chosen because it minimizes convection currents' in the diffusion zone. It has the further advantage that the boundary conditions are such that a slight modifica- tion of Anderson and saddington's8 solution of Fick's Law yields an equation which requires measurements only of the length and the initial and final average specific activities of the solidified melt within the capillary. where t is the diffusion time, Co is the average specific activity of the melt contained in the capillary at t = O, C is the average specific activity of the melt contained in the capillary at t = t, 1is the length of the capillary, and D is the self-diffusion coefficient. The equation is of somewhat different form than those previously applied to high temperature diffusion studies because the specific activity of the melt in the reservoir was negligible both before and after diffusion. The diffusion apparatus is shown schematically in Fig. 1. It consisted of a silicon carbide resistance furnace containing the inactive melt in a graphite crucible, internal dimensions 7/8 by 4 in., enclosed in a 1 1/4- by 1 1/2- by 30-in. McDanel tube. A 3/8-in. McDanel thermocouple sheath to which graphite radiation shields and a graphite protection tube were affixed, was used to hold the capillaries. By moving this sheath through a rubber seal at the top of the McDanel tube the capillaries could be lowered into or raised out of the melt. Temperature was measured with a Pt-Pt 13 pct Rh thermocouple which was calibrated periodically against a standard couple. The furnace temperature was controlled to ± 5°C through the thermocouple immersed in the melt. Temperature variation over the depth of the melt was less than ± 3°C. The inactive melts were prepared from pure native quartz, assaying better than 99.9 pct SiO2, A.R. grade A12O3 and A.R. grade CaCO,. The same quartz and CaCO3 were used in preparing the active melts, the

Jan 1, 1962

By J. C. Savins

The practical analysis of the hydrodynamics of the wellbore has long been a subject of interest to engineers. This paper presents a simplified solution to the problem of computing the pressure drop for the flow of drilling mud in the annulus of the wellbore. This solution is, however, an exact and rigorous solution under the assumptions which have been imposed. These assumptions are that the drilling fluid is a Bingham plastic fluid* and that the annulus is formed by two concentric, stationary, cylindrical pipes. It is further assumed that the fluid is incompressible and that its motion is isothermal and in a steady state. This problem under the same assumptions has been attacked by previous authors. Beck, Nuss and Dunn' proposed that the equation for the flow of a Bingham plastic fluid in a cylindrical pipe could be applied to an annulus if the pipe radius were replaced in the equation by the hydraulic radius. This equation, known as the Buckingham-Reiner equation' (see Appendix 1), was also used in an approximate form. Van Olphen pointed out that even for a simple or Newtonian- fluid the pipe equation (Poiseuille's law) could not be converted to the Lamb equation escriptive of flow in an annulus (see Appendix 1) by using the hydraulic radius. Van Olphen further attempted to give a solution for the annular flow of a Bingham plastic fluid by introducing approximations similar to those which have been used in the case of the Buckingham-Reiner equation. Other attempts to provide approximate or exact solutions have been made by Grodde' and by Mori and Ototakeq. The present authors some years ago in unpublished work derived the correct expressions relating the pressure drop and flow rate for this problem. It was found that the solution consisted of two simultaneous equations, one of which contained a logarithmic term. Thus, obtaining numerical results for any particular case of interest involves very tedious trial-and-error computations. Very recently Laird presented the correct derivation of the two equations which are given in full detail in Appendix 1. In order to reduce the amount of calculation time which would be involved in providing a complete tabular or graphical solution to the problem, a high-speed electronic digital computer has been utilized. For this purpose the two simultaneous equations were transformed into more compact expressions by introducing reduced variables. These expressions are given in the following theoretical section. A similar procedure in this problem has been developed by Fredrickson and Bird1" Their tabular results, however, are very incomplete in the range of practical interest for problems of wellbore hydrodynamics. We have furthermore been able to express our graphical results in terms of convenient and familiar dimensionless groups. THEORETICAL DEVELOPMENT Use of Reduced Variables In terms of reduced variables the two simultaneous equations just discussed take the following form, The reduced variables q, x, a and z are defined in terms of the various measured quantities, where Q is volumetric flow rate, AP/L is pressure gradient, Dl is OD of inner pipe, D, is ID of outer pipe, is plastic viscosity, and is yield point. Thus, we have a dimensionless volume flux, a dimensionless reciprocal pressure gradient, and the ratio of the pipe diameters Before introducing the fourth reduced variable, z, it is of interest to consider the physical significance of the parameter x. As may 'be seen from the velocity profile of Fig. 1 the Bingham plastic fluid has the interesting property that a portion of the stream flows at a uniform velocity without shearing action. This section of the stream is situated approximately in the center of the conduit and is known as the "plug flow" region. Its existence is due to the fact that the shearing stresses within the region do not exceed the yield point, which is one of the two flow properties characterizing the fluid. The parameter x then turns out to be the ratio of the

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for OFHC copper, and for a series of binary solid solutions of high purity copper with zinc, gallium, germanium, arsenic, and silicon, to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity. The apparatus used was of the torsional pendulum type developed by KeI1 modified so that the specimen and vibrating system could be maintained in a high vacuum. The activation energy for grain boundary relaxation in copper is 33,000 cal per mol. This is considerably less than the activation energy for self-diffusion, in disagreement with Ke's theory2 that the two activation energies should be the same. All the alloying elements increase the activation energy for grain boundary relaxation to approximately 44,000 cal per mol, increasing the grain boundary viscosity at a given temperature. The results are discussed in terms of theories of grain boundary slip put forward by MottQ and by Ke.+ Experiments have also been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. EXPERIMENTS described in this paper were designed to investigate the effect of alloying elements in substitutional solid solution on grain boundary viscosity, using the internal friction method developed by Kel for measuring grain boundary viscosity. It was considered desirable to make the system under investigation as simple as possible by making experiments on a comprehensive series of binary alloys of copper with the elements immediately following it in the periodic table, i.e., zinc, gallium, germanium, and arsenic. These elements are within the range of favorable size factor for solution in copper, and the systems have been extensively investigated by Hume-Rothery and his co-workers." Later, in order to study the effect of the relative size of the solvent and solute atoms, experiments were made on a series of Cu-Si alloys, since the apparent atomic diameter of silicon when in solution in copper—the diameter necessary to assign to the solute atoms to account for the lattice constant of the solid solutiona—is almost the same as that of the solvent atoms. Preliminary experiments were made to measure the variation of internal friction with temperature for pure copper. Ke made some experiments on copper," but found that the curves obtained were not reproducible in consecutive experiments. The copper was maintained in an argon atmosphere during the experiments but, although he took precautions to exclude oxygen, Ke came to the conclusion that the precautions were not entirely satisfactory, and that the lack of reproducibility must be due to absorption of oxygen by the copper. Experiments have therefore been made to investigate the effect of small amounts of oxygen on the variation of internal friction with temperature for copper. Previous Work Ke made extensive experiments on high purity aluminum and was able to show that the grain boundaries behave viscously at high temperatures. He found that the relative rate of movement of the grains could be expressed as Where v is the velocity of slip, A is the constant, u is the shear stress, H is the activation energy, R is the gas constant, and T is the absolute temperature. By assuming that the boundary layer was one atom thick, he obtained a value for the viscosity which, when extrapolated to the melting point, gave good agreement with the viscosity of the liquid metal at the melting point. Ke also made experiments on other high purity and commercial purity metals:, and on some alloys." " He came to the conclusion2 that the activation energy for grain boundary slip was the same as for self or volume diffusion and for steady state creep in single crystals. Rotherham, Smith, and Greenough" have shown recently that the activation energy for grain boundary slip is not the same as for self-diffusion in tin,

Jan 1, 1957