Search Documents

By Morris Muskat

It is pointed out that the application of capillary pressure curves obtained by drainage or desaturation processes to the calculation of the fluid distribution in interphase transition zones involves a number of difficulties; namely: (I) the development of very low nonwetting phase saturations appears to be in contradiction with the lack of mobility of such distributions indicated by permeability-saturation curves, (2) dispersed nonwetting phases are thermodynamically unstable, and (3) discontinuous phases should not be subject to hydrostatic equilibrium requirements. While these difficulties could be obviated by assuming that the capillary pressure drainage curve has an initial horizontal segment, they are automatically circumvented by application of the imbibition capillary pressure curve to the lower part of the water-oil transition zone. These generally show zero displacement pressure at only partial wetting-phase saturations. The countercurrent upward flow of oil into the main oil-saturated pay and downward drainage of water also suggests that wetting phase imbibition processes will control the saturation distribution immediately above the water-saturated section. Similar considerations, with a generalized interpretation of the apparent wetting-phase behavior of the oil and gas phases, provides a basis for constructing the curve for fluid distribution in the oil-gas transition zone. In the transition zones so derived, the oil begins with a nonvanishing saturation at the water-oil contact and terminates with a similar saturation at the top of the gas-oil contact. The gas-oil transition zone begins with an equivalent nonvanishing gas saturation. Introduction It has been a common assumption for some years that the nature of the fluid dis- tribution in virgin reservoirs, and in particular that in the transition zones between the oil and water and between the oil and gas sections, can be computed by a simple application of capillary pressure data. The results of such calculations appear to have been first reported by Leverett.' The latter, however, indicated only the numerical values of the parameters used in the computations, without explicitly describing the procedure. Leverett's illustrative calculated transition zones are reproduced in Fig I. Although no critical study of the apparently obvious method of calculation has been published, one cannot proceed very far in the computation without encountering some rather fundamental questions not yet answered in the literature. This paper is not written under the pretense that the whole transition-zone problem has been fully and satisfactorily solved. Its purpose, rather, is to discuss suggestions for its treatment, much of it admittedly hypothetical, and emphasize the nature of the uncertainties arising therein; for the literature, as now available, gives little indication that there are any problems still outstanding. The Transition-zone Equation The basic equation, which presumably gives directly the fluid distribution without recourse to any further consideration, is: Ap = (r1 - r2)gh [1] where r1, y2 are the densities of the two contiguous fluids, h is the height above the "capillary-free" zone of complete saturation with fluid I, g the acceleration of gravity, and Ap is the capillary pressure across the average interface at the height

Jan 1, 1949

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By J. P. Zannaras

If we assume that testing of the model started at time C, that time t2 was the instant at which the elastic limit of the material was passed at the points of the maximum stress, and that at time t3 the failure of the model was completed as shown in the typical photograph (Fig. 1), then actually the photograph shows the final results of what took place between time t2 and t3. By the principle of similitude all conclusions drawn from the behavior of the model were applicable and valid for actual mine roofs up to the time t, after time t, motions and friction came into play during the destruction of the model. The events between t2 and t3 and the photograph itself are not representative of the events expected in an actual mine roof unless corrections imposed by the principle of similitude are made.

Dec 1, 1956

By William P. Blake

Travelers in the desert regions of the southwestern portion of United States, especially along the valley of the Colorado of the West, can hardly fail to note that most of the rocky outcrope of the harder rocks have a uniform prevailing blackness of the surface, in strong contrast with the normal color of the interior of the rock when freshly broken. For example, the granitic or gneissic rocks of Pilot Knob, below Yuma, are blackened beyond easy recognition. So also rocks upon the lower Mojave in California are so thoroughly blackened, as if painted, that ordinary gneiss can scarcely be recognized without breaking it so as to show the interior color and structure. The discoloration is not confined to the rocky outcrops in place, but is found upon boulders and upon the loose rounded pebbles which strew the surface of the mesas along the Colorado river. These fragmentary rocks partake of the general blackening.

Jan 1, 1905

By Robert H. Richards, E. E. Bugbee

Friends often ask how accurate the work of our little stamp mill is, or express the opinion that a little mill cannot do good work. As a reply we would like to place on record the results of a few tests. There are two periods of work in our laboratory; the fall term, when the class collectively goes through all our chief laboratory-processes, and the spring term, when the students work up their theses, each electing some one process or investigation and devoting himself wholly, or almost wholly, to that. Some of the tests, the results of which are recorded in this paper, were made in the fall term; the preparation of the apparatus, the sampling and the assaying being done largely by assistants, with the aid of the students. Others were made in the spring term as thesis-work, and the results are due wholly to. the students. The complete " tree " of our process is patterned after the-

Jan 1, 1904

By George L. Porter

Mr. President and Gentlemen of the Institute of Mining Engineers: . Unofficially representing the people of the vicinage, it is my pleasant duty to welcome you to the city of Bridgeport, to the valley of the Naugatuck, to the State of Connecticut. The importance and wide-reaching influences of the investigations for which your Institute is organized, the beneficial results which have directly and indirectly blessed mankind from your and kindred studies, the distinguished position which has been achieved in the scientific world by the Institute as a society, and the personal reputation which is the proper recognition of the ability and knowledge of its individual members, assure all that in attempting to honor you we are ourselves honored. In the republic of knowledge no fictitious rewards dignify the incompetent and the ignorant—the attested success of inventions and discoveries in the workshop of nature differentiates her real citizenship. Your present place of meeting is wisely selected ; for this senti-

Jan 1, 1895

By S. L. Hoyt

ABOUT three years ago eight standard steels were prepared for the cooperative investigation of methods for oxygen analysis, sponsored by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers and by the National Bureau of Standards. A preliminary report of the results was made at the annual meeting of the A.I.M.E. in February, 1936. ? This report showed the reliability of vacuum-fusion methods and further brought out certain advantages of the fractional vacuum-fusion method. The results obtained by the authors with the latter method will be discussed here, with some com-ments on the procedure for those who are interested in determinations of gases in steel. Some additional comments are offered on the use of the polarizing microscope for identifying the inclusions in the steel to check and amplify the findings of the fractional vacuum-fusion analysis. For details of the fractional method, see the paper by L. Reeve1.

Jan 1, 1937

By A. S. M’Creath, E. V. d’Invilliers

The rapid development of the southern coal and iron-ore fields during the past few years, and especially in the latter half of the year 1886, and the avidity with which everything relating to the industrial situation there is read and absorbed by the professional and non-professional public, has led to the preparation of a brief paper for the Institute upon a comparison of the raw materials available on or about January 1st, 1887, at three prominent centers of consumption. While disclaiming any originality or priority in the treatment of the resources of these districts, where so much valuable and interesting work has been performed in the past by several members of the Institute, we hope that the presentation of some analyses of samples personally secured by us in the several districts selected, and prepared for a comparative study of the character of the materials actually used and to be used by the furnaces of the "New

Jan 1, 1887

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964

By R. Schempp

DURING the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these char-acteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and empha-sized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent cart on. The discrepancies encountered in the determination and classification of the austenitic grain size led to in investigation of some of the variants influencing the austenitic grain size as determined by standard methods.

Jan 1, 1937

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

By John C. McDonald

This report is a continuation of an earlier one with a similar titlell to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as reported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be compared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a considerable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated. Procedure The alloys were cast in the form of cylindrical ingots, which were extruded into bar before being rolled. Some of the ingots were made in 2-in. diameter molds whereas all of the alloys of the previous paper were cast in 4.in. molds. For the larger ingots, the extruded bar was 2 by 0.140 in.; lor the 2-in. ingots, it was I by 0.100 in. Preliminary work indicated that strip rolled from both sizes of the bars would have substantially the same properties. The bar was rolled at some temperature in the range 400' to 800°F., for a total reduction of 50 per cent. The temperature and reduction per pass were so selected that no cold cracking occurred, but were such as to leave the metal in a semihard condition. The hot-rolled metal was annealed at several temperatures in the range 400' to 800°F.; it was also cold-rolled, and given solution and aging treatments. Two standard test bars corresponding to each treatment were pulled in tension, and the average was obtained. Twelve treatments, in all, were given each alloy. The properties of the annealed specimen having the highest percentage of elongation were selected to represent the alloy in the annealed condition. The properties of the cold-rolled specimen having the highest yield strength were selected to represent the alloy in the cold-rolled condition. These properties were then plotted against percentage composition by analysis. Smooth curves were drawn among the points, thus graphically averaging the results over the entire range studied. The percentage of elongation in the cold-rolled state was not plotted, since it was always low, and varied in an irregular manner with composition. Alloys Studied Magnesium-calcium Alloys.—Fig. I presents the results on the alloys of the rnag-

Jan 1, 1941

By Harry H. Angst

THE history and efficiency of 40-ton capacity dump trucks for surface waste removal at the New Cornelia opencut copper mine, at Ajo, Ariz., are summed up in this paper. Tabulations of truck performance, together with detailed cost figures, prove the value of truck transportation for certain special operations at a large mine. Emphasis is given to the fact that truck transportation not only reduces the haulage costs but also reduces the breaking ground and shovel-loading costs per ton. The New Cornelia opencut copper mine is in the desert. The climate is ideal for seven months of the year, but the five summer months are uncomfortably hot. The elevation is 1820 ft. above sea level and the annual rainfall is approximately 6 inches. The ore body is a monzonite-porphyry deposit. The waste-rock capping consists of hard rhyolite, conglomerate and porphyry. All the material is hard and cannot be excavated without blasting. The rhyolite and conglomerate waste is very blocky. The weight of the rock in place is 2.16 tons per cubic yard. The average mine production per day is 22,000 tons of ore and 18,000 tons of waste rock, the latter consisting of surface rock and material within the ore body too low in grade to send to the concentrator. The rock is loaded by electric shovels with 4 ½ -cu. yd. dippers. The primary transportation of ore to the concentrator and waste to the dumps is by 30-yd. dump cars and oil-burning steam locomotives; therefore truck haulage of waste is a minor factor of the New Cornelia operation. However, as New Cornelia was one of the first mines to use large-capacity dump trucks for haulage, the results obtained are of interest. EQUIPMENT On the south side of the New Cornelia is a hill rising about 500 ft. above the normal surface elevation, roughly 1000 ft. in diameter at its base, called locally Arkansas Mountain peak. Exploratory drilling in this area developed additional ore that could be made accessible for open pit operation only by moving the mountain face a maximum distance of 400 ft. to the south. The slope of the mountain adjacent to the pit averaged 35°, and the small area involved precluded the use of train haulage for the removal of the 4,000,000 tons of waste estimated above the normal pit elevation. A study of dump-truck haulage at Boulder Dam and San Gabriel Dam led to the decision to use large-capacity end-dump trucks rather than smaller trucks, for the following reasons: 1. The truck would have to withstand the impact of hard, heavy chunks, some of them weighing as much as 10 tons, which would be dumped from the 4 ½ -cu. yd. dipper. 2. The coarse, rocky, abrasive material would soon damage a light truck body. 3. The body of a small truck could not be efficiently loaded with coarse rock.

Jan 1, 1941

By John C. McDonald

This report is a continuation of an earlier one with a similar titlell to which the reader is referred for such details of procedure as do not appear here. A brief summary will be given of the objects and methods of the research at this time. It was pointed out in the previous paper that properties of magnesium alloys, as reported by different workers, often differ. This was thought to be due to differences in the preparation of the specimens tested. The ideal way to compare alloys would be to prepare each of them in so many ways that reasonable assurance would exist that the best properties of each alloy had been developed. The alloys would then be compared on the basis of these properties. The treatment actually given the alloys of these studies is necessarily a compromise with completeness. Nevertheless, enough treatments have been given so that a considerable degree of assurance exists that the properties obtained are representative of the alloy as such, and not merely of the manner in which it was worked and heat-treated. Procedure The alloys were cast in the form of cylindrical ingots, which were extruded into bar before being rolled. Some of the ingots were made in 2-in. diameter molds whereas all of the alloys of the previous paper were cast in 4.in. molds. For the larger ingots, the extruded bar was 2 by 0.140 in.; lor the 2-in. ingots, it was I by 0.100 in. Preliminary work indicated that strip rolled from both sizes of the bars would have substantially the same properties. The bar was rolled at some temperature in the range 400' to 800°F., for a total reduction of 50 per cent. The temperature and reduction per pass were so selected that no cold cracking occurred, but were such as to leave the metal in a semihard condition. The hot-rolled metal was annealed at several temperatures in the range 400' to 800°F.; it was also cold-rolled, and given solution and aging treatments. Two standard test bars corresponding to each treatment were pulled in tension, and the average was obtained. Twelve treatments, in all, were given each alloy. The properties of the annealed specimen having the highest percentage of elongation were selected to represent the alloy in the annealed condition. The properties of the cold-rolled specimen having the highest yield strength were selected to represent the alloy in the cold-rolled condition. These properties were then plotted against percentage composition by analysis. Smooth curves were drawn among the points, thus graphically averaging the results over the entire range studied. The percentage of elongation in the cold-rolled state was not plotted, since it was always low, and varied in an irregular manner with composition. Alloys Studied Magnesium-calcium Alloys.—Fig. I presents the results on the alloys of the rnag-

Jan 1, 1941

By Raymond Mancha

A test of any fan requires the determination of such data as fan pressure, air volume handled by the fan, and power input to the fen shaft. When testing operating mine fans of the centrifugal type, test methods have been employed, for the sake of convenience, that permit great latitude in detail of procedure resulting in wide variance in results by different investigators. Some controversial aspects of field fan testing are the result of past failure to define clearly the various forms of fan pressure and to a lack of understanding of the accurate procedure for the measurement thereof. Also, the anemometer for air-volume measurement, although convenient, if carelessly used and maintained is subject to a wide error range with variation in method of application and in instrument accuracy. The appearance of the axial-flow type of mine fan offers the possibility of refinements in field testing that were impractical with the centrifugal fan. First of all, the fan inlet and outlet are more sharply defined, giving closer agreement as to just where the fan begins and ends; thus there is less disagreement as to the proper location for measurements of fan pressure. The area of passage into the inlet of an axial-flow mine fan usually constricts, causing high air velocities with accompanying steadiness of flow. Thus the fan inlet offers an ideal location for accurate air-volume measurements with the pitot tube, the proper use of which is well established by code. Thereby the controversial aspects of such measurements are eliminated. Use of the Pitot tube also facilitates a more accurate measure of fan pressure, since the individual pressures measured can be properly weighted, as will be explained later. Determination of power input to the axial-flow mine fan operating in the field is subject to the same inaccuracies as with the centrifugal fan if the axial-flow fan is also belt driven. However, because of the higher rates of rotation usual with axial-flow fans, direct-driven units are more numerous and it is unnecessary to assume a drive efficiency, thus eliminating one possible source of error. It is the purpose of this paper to define and explain the various types of pressure measurements involved in a field test of an axial-flow mine fan, and to further explain the proper use of the Pitot tube when measuring pressures and volumes. DefinitioN of Fan Pressures The two fan pressures most commonly discussed are fan total and fan static pressure, each of which has the same meaning regardless of whether the fan is blowing, exhausting, or blowing and exhausting, as in the case of a fan with ducts connected to both outlet and inlet. Fan total presscre is the amount by which the total pressure of the air delivered by the fan exceeds the total pressure of the air received by the fan. This pressure is a measure of the maximum amount of the work done on the air by the fan that is available for external use.

Jan 1, 1942

By R. G. Patterson

The usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired sue and shape, and in one method1 a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averag- ing a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer's knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. Method The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or dia-magnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. Description of Apparatus Of many alternating-current bridge methods applicable,3 the one shown in Fig. 1 (Owen's bridge') was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by PlL1. It is connected to the bridge by about

Jan 1, 1946

By E. V. Potter, E. T. Hayes, H. C. Lukens

Large volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that bite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.l.2 The close relationship between iron and manganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. Apparatus The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of IOO C.C. for a 60-cm. length. For larger changes in gas volumes, auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By R. G. Paterson

THE usual procedure in determining the magnetic susceptibilities of rocks and formations has been to take samples in the field and measure their volume susceptibilities in the laboratory, using one of numerous methods available. In none of these methods is the measuring instrument suited for field use. Usually the sample is pulverized; sometimes it is machined to a desired size and shape, and in one method' a cast of the sample is made and the susceptibility of the rock compared with that of a material of known susceptibility of the same size and shape, made from the cast of the original sample. Some writers assert that the difference in susceptibility of a rock sample in powdered and solid forms is negligible, and while doubtless this is true in many cases there are others in which the difference becomes appreciable. Further, the susceptibility of a small specimen may differ from that of the rock from which it is taken, owing to the stresses produced by the hammering or other forces used to obtain the sample and shape it for testing. Wilson2 found that an individual specimen of granite had about the same susceptibility in the solid as in the powdered form, but that pieces from different parts of the rock varied as much as 750 per cent because of unequal distribution of magnetite. The most accurate value of susceptibility would, obviously, be obtained from averaging a number of tests on the undisturbed rock instead of from one or two samples. No such procedures have been published, to the writer's knowledge. It is the purpose of this paper to describe a method by which susceptibilities of rocks may be determined in place by means of a portable instrument. METHOD The principle involved in this new method is that there is a change in inductance of a coil due to the presence in its magnetic field of a paramagnetic or diamagnetic medium. In this case, however, the windings of the coil do not enclose any part of the rock under test. Instead, the coil is circular, being small in cross section as compared to its radius, and consists of several hundred turns of fine wire. It is placed flat on the rock of which the susceptibility is to be measured. Thus only part of the magnetic field from the coil penetrates the rock under test. The relation between the change in field strength or inductance of the coil and the susceptibility of the medium will be developed later. To measure the change in the inductance of the coil due to the presence of a magnetic material an alternating-current inductance bridge was chosen. DESCRIPTION OF APPARATUS Of many alternating-current bridge methods applicable,3 the one shown in Fig. I (Owen's bridge') was adopted for its simplicity and sensitivity. In Fig. I, the test coil is indicated by P1L1. It is connected to the bridge by about

Jan 1, 1941

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945