Search Documents

By W. S. Morris, R. R. Bradenthaler, G. Wade

Petroleum engineers generally are of the opinion that the flow conditions and, therefore, the formulas that apply to the flow of oil and gas in long pipe lines differ in many ways from flow conditions in oil wells. One of the reasons why the formulas in common use for pipe-line flow do not correctly apply to oil wells is that the flow lines are vertical and not horizontal. Another factor to be considered is that the fluid is a mixture of oil and gas and that the physical characteristics of these two components are affected differently by changing conditions of pressure and temperature during upward flour. Realizing the need for accurate data on flow in vertical pipes under conditions caused both by natural flow and the gas-lift, the U. S: Bureau of Mines has installed equipment at the Petroleum Experiment Station, Bartlesville, Okla., for the purpose of studying this problem. In additon a study will be made of the comparative effects of different natural-flow and gas-lift methods of producing oil on ultimate production from reservoir sands. Experimental Equipment The experimental equipment consists of a regular oil-field steel derrick, a large pressure tank installed in a concrete pit beneath the derrick floor, compressors and pumps, gas separators and absorbers, metering and control devices, and the necessary pipe connections. The crown-block level represents the derrick floor at an oil well, and the "producing sand" is the pressure tank below the derrick floor. The difference in elevation between the crown-block level and the tank is 90 ft. Figs. 1, 2 and 3 show the construction and exterior arrangement of the equipment. The success of the experiment will of course depend largely upon the accuracy of the oil and gas measurements and the temperature and pressure determinations. Because extreme accuracy is necessary, all oil and gas measurements will be checked at least twice, and in some

Jan 1, 1929

By Zay Jeffries

This paper will include a brief discussion of Prof. Howe's paper on The Supposed Reversal of Inheritance of Ferrite Grain Size from that of Austenite.l The general subject of grain refining in steel and iron will also be treated. The conclusions reached are stated in the following hypotheses which are discussed more in detail below. 1. The ferrite grain size in pure iron, the ferrite and pearlite grain size in hypoeutectoid steel, the pearlite grain size in eutectoid steel and the cementite and pearlite grain size of hypereutectoid steel are not inherited from the grain size of the mother austenite. 2. The only structural feature that is generally inherited from the austenite of hypo- and hypereutectoid steels on cooling through their transformation ranges is the position of the excess ferrite or cementite at the austenite grain boundaries, sometimes causing complete and sometimes incomplete networks which outline the old austenite grain boundaries. Rapid cooling through the transformation range will cause the non-inheritance of this structural (network) feature. 3. The austenite grain boundaries themselves are nearly always effaced in all steels and also in pure iron during the At transformations. 4. The grain-size refining of steel and iron is brought about by the combined effect of non-inheritance of the transformation products on either heating or cooling, i.e., the austenite transformation products do cst inherit their grain size from the austenite on cooling through the transformation range nor does austenite inherit its grain size from the products which form austenite on heating. 5. In general, in both iron and carbon steel the larger the austenite grain size, the larger will be the grain size of the transformation products on cooling. This, of course, assumes all other conditions constant except the austenite grain size. An exception is found to this general rule in very pure iron such as electrolytic iron. In this instance small austenite grains may form very large ferrite grains on cooling through Arg.

Jan 1, 1918

By G. F. Comstock

THE subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: (1) That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. (2) That the quality of the metal and the mill practice must have something to do with them. The first point of view was most-ably and logically presented by J. E. Howard,1 and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these. failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior roach-bed; while the railroad men,, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work clone in this laboratory, as well as the work of other investigators of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. . Within the last year or two, however, since the method of etching polished sections for the microscope with a cupric chloride solution has been tried systematically. on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 11, 1918

By Paul M. Tyler

Mineral raw materials, because they are essential to our industrial prosperity and military strength, must be made available in substantial quantities. regardless of cost. Variations in the cost of procuring minerals, as compared with the cost of obtaining other commodities, and changes in the cost of production of different minerals relative to one another, will naturally influence the quantities of a given mineral item that can be marketed readily. However, in the last analysis, the cost of winning minerals from the ground usually constitutes only a small fraction of the value of the end-use products and services derived from them. The miner's share of the cost of a typewriter, telephone circuit, or even a modem office building, is almost insignificant. Far more important to the ultimate consumer, therefore, than any minor saving in cost is the assurance of ample supplies of the minerals needed to aliment our expanding economy. To create a successful metal mining operation involves ( 1 ) the discovery and systematic development of a mineral deposit, (2) extraction of the ore, (3) the mechanical and metallurgical processing to eliminate worth- less or harmful impurities, and (4) the profitable disposal of the product. The first step of the technological process belongs chiefly in the realm of the geologist, the second is a mining engineer's job, the third is mainly up to the millmen and extractive metallurgists; whereas the fourth and equally important step poses a commercial problem that has aspects in common with the marketing of other products. Ore finding is far from being an exact science. There is no mathematical criterion for evaluating the efficiency of prospecting and exploration. Lady Luck shares the honors or assumes part of the blame along with the prospector and geologist. Marketing like- wise involves factors that seemingly defy engineering analysis. Although the other steps can be measured with some degree of mathematical accuracy, even they tend to vary so widely in basic principle, as well as in

Jan 1, 1959

By G. F. Comstock

The subject of transverse fissures in steel rails has been discussed very thoroughly in recent years from various points of view and the final opinions expressed may be roughly classified into two groups: That these fissures are the result merely of fatigue of the steel and are independent of the quality of the metal. That the quality of the metal and the mill practice must have something to do with them. The first point of view was most ably and logically presented by J. E. Howard,' and in the discussion of this paper, as well as in several other preceding publications, Dr. P. H. Dudley, Consulting Engineer of the New York Central Lines, has strongly defended the other opinion.2 The steel makers of the country have naturally rallied under Mr. Howard's banner, hoping to place the entire blame for these failures upon the railroads with their high wheel-loads, hard steel, heavy traffic, and sometimes inferior road-bed; while the railroad men, on the other hand, have been busy accumulating statistics and records in the effort to find an actual reason in the rails themselves that would account for the seemingly haphazard occurrence of transverse fissures under varying conditions and at widely separated points. The view that these fissures were due merely to normal fatigue under alternating stresses seemed most reasonable to the writer until quite recently, because from work done in this laboratory, as well as the work of other investigators, of the problem, no structural differences, in the vast majority of cases, were found between metal at the nuclei of transverse fissures and metal at similar positions in the same rails or in other rails that had not developed fissures. Within the last year or two, however, since the method of etching polished sections for the microscope with a oupric chloride solution has been tried systematically on lengthwise sections, passing through the nuclei of transverse fissures, evidence

Jan 1, 1920

By Paul M. Tyler

Mineral raw materials, because they are essential to our industrial prosperity and military strength, must be made available in substantial quantities regardless of cost. Variations in the cost of procuring minerals, as compared with the cost of obtaining other commodities, and changes in the cost of production of different minerals relative to one another, will naturally influence the quantities of a given mineral item that can be marketed readily. However, in the last analysis, the cost of winning minerals from the ground usually constitutes only a small fraction of the value of the end-use products and services derived from them. The miner's share of the cost of a typewriter, telephone circuit, or even a modem office building, is almost insignificant. Far more important to the ultimate consumer, therefore, than any minor saving in cost is the assurance of ample supplies of the minerals needed to aliment our expanding economy. To create a successful metal mining operation involves (1 ) the discovery and systematic development of a mineral deposit, (2) extraction of the ore, (3) the mechanical and metallurgical processing to eliminate worthless or harmful impurities, and (4) the profitable disposal of the product. The fist step of the technological process belongs chiefly in the realm of the geologist, the second is a mining engineer's job, the third is mainly up to the millmen and extractive metallurgists; whereas the fourth and equally important step poses a commercial problem that has aspects in common with the marketing of other products. Ore finding is far from being an exact science. There is no mathematical criterion for evaluating the efficiency of prospecting and exploration. Lady Luck shares the honors or assumes part of the blame along with the prospector and geologist. Marketing like- wise involves factors that seemingly defy engineering analysis. Although the other steps can be measured with some degree of mathematical accuracy, even they tend to vary so widely in basic principle, as well as in

Jan 1, 1964

By Archer E. Wheeler, Milo W. Krejci

The Boston & Montana Reduction Works at Great Falls, Mont., was formerly the reduction works of the Boston & Montana Consolidated Copper & Silver Mining Co., and continued as the reduction plant for the independent company until June 1, 1910, when the consolidation of a large number of the operating companies of Butte was effected. It then became merged in the Anaconda Copper Mining Co. as the Boston & Montana Reduction Department of the Anaconda Copper Mining Co. The history of copper converting at this plant, while not covering the entire period of the commercial use of the process in this country, does cover by far the larger part of it, and as the operation of and appliances for the process have undergone many changes during the time, it may, perhaps, be of some interest to put the record of these changes into permanent form. The plan followed in the preparation of this paper has been to give first a brief chronological record of the principal events and changes and then, even at the risk of some repetitions, to give more detaild accounts of some of these changes under separate headings. The headings for the complete paper are as follows: 1. General. Chronological Review. 10. Development of Different Classes 2. Mechanical Manipulation. of Converters After Class I. 3. Casting of Finished Copper. 11. Basic Lining. 4. Tamping of Linings. 12. Number and Size of Tuyeres. 5. Early Acid Linings. 13. Cast Copper Tuyeres. 6. Acid Linings With the Use of Ore. 14. Efficiency of Air. 7. Introduction of Flux Through the 15. Size of Converter Mouth. Tuyeres. 16. Height of Converter. 8. Bottom Blast. 17. Summary. 9. Disposal of Converter Slag, General Chronological Review. Ground was broken for the general concentrating and smelting plant in the spring of 1,891. The first departments to start operations were the concentrator in March, 1892, and the Brückner roasting and reverbera-tory smelting departments in April, 1892. The converter department

Jan 1, 1914

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By F. S. McNicholas, M. S. Walker, V. C. Rogers

During the year of 1944 and the first half of 1945, the Climax Molybdenum Co. made a study of some of the problems in block and panel caving, with the use of a scale model. The experiments dealt essentially with the type of rock and conditions at Climax, but some experiments were carried out to simulate conditions found in other mines. Most of the previous experiments on the caving characteristics of rock have dealt with sedimentary or broken igneous material. The series of experiments described here was designed to show the caving action of unbroken igneous rock. Con- siderable difficulty was experienced in duplicating unbroken material in the model. The results obtained are believed to be relatively correct, but verification must necessarily come from future mine operation. Observations in the mine and glory hole, together with statistical data, were used as criteria for creating similar conditions in the model. In 1913, George R. Lehman' experimented with broken material in a model for the Inspiration Consolidated Copper Co. and, more recently, P. B. Bucky2 experimented with broken material with a capping of mill tailings. Mr. Lehman's model represented a maximum ore height of 70 ft. capped by 55 ft. of waste. He varied the draw-hole spacing from 6¼ ft. to 8? ft. and 12½ ft. The material used graduated from fines to 30-in. maximum size. Some of his conclusions were: "(I) The less the distance between chute centers, the greater the extraction (Fig. I); (2) the higher the ore column, the greater the extraction; (3) the less the amount drawn at a time from each chute, uniformly, the greater the extraction of clean ore before the capping appeared, but not the greater the total extraction to a I per cent copper final product." (Fig. 2.) Professor Bucky concluded, in part: "(I) Drawing of ore may take place at any time from any finger and in any amount without affecting materially: (a)

Jan 1, 1946

By J. M. Toguri, K. Grjotheim

It is known 1,2 that the equilibrium between titanium metal, TiCl2 , and TiCl3, in a solvent of molten metal chlorides, is influenced both by the total amount of dissolved titanium and by the type of solvent. Assuming that the trivalent titanium forms the complex ion Ti111 Cl4, the equilibrium reaction may be expressed by the following equation, (Me) TiIII cl4+ 1/2 Ti = 3/2 TiII cl2+ (Me) Cl The ideal ionic equilibrium constant for this reaction is, Where the N's are the molar ionic fractions in the equilibrium melt, and (Me) the different types of cations present in the equilibrium mixture. The following thermodynamic relation is derived between Kand the concentration of cations in the equilibrium melt, mix The N"S are the equivalent ionic fractions, and so forth are constants corresponding to the standard changes in free energy for reactions in melts where only the cation indicated is present, and f (y1) is a function of the activity coefficients in the equilibrium mixture. When this term vanishes, a simplified linear relationship between In Kideal and the concentration is obtained. The simplified relationship has been applied with satisfactory results to the experimental data of Mellgren and pie,' and Kreye and Kellogg.2 MANY existing methods for the production of light metals involve the reduction of their respective metal halides in the presence of salt melts composed of alkali or alkaline earth chlorides. In such a solution phase, the light-metal halide may undergo stepwise reduction from a higher, to a lower valence, and finally to a zero valent state. In this connection, the disproportionation equilibrium is of great interest. In the case where the higher valence is three and the lower valence is two, the disproportionation equilibrium may be written as follows, 3 Me11 = 2 Me111 + Me [I] If this equilibrium occurs in a salt melt containing a large excess of alkali chlorides, a typical ionic melt is obtained. It is then possible to formulate the cation equilibrium: 2 Me+h' + Me = 3 Me++ [II] Reaction [11] is analogous to a cation exchange reaction. It has been shown thermodynamically that the equilibrium constant for such a reaction in 2

Jan 1, 1960

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By G. W. Thomas

A mathematical tnodel of forward combustion in an oil reservoir is treated in this paper. The model describes a radial system having a vertical section of essentially infinite thickness, all of which is permeable to gas flow. Combustion, however, is presumed initiated over a limited thickness of the total vertical section. In the interval supporting cotnbustion, the mechanisms of radial conduction, convection and heat generation are taken into account. Above and below the burning interval, heat transport in the radial direction is by cottduction and convection. Vertical heat losses from the ignited interval are accounted for by conduction alone. A general solution is presented for the temperature distribution caused by radial movement of the combustion front. The results show that no feedback of heat occurs into the ignited interval when convection and conduction are acting in the bounding media. Peak temperatures are also 5 to 10 per cent higher than in the case where heat transport in the bounding media is by conduction alone. We arbitrarily define vertical coverage to be that fraction of the total ignited interval which is at 600F above atnbient, or greater, at any given time. The radial distance at which the vertical coverage becomes zero is the propagation range of the combustion front. It was found that an increase in vertical coverage results when the oxygen concentration, fuel concentration or gas-injection rate is increased. Moreover, the combustion front can be propagated 10 to 15 per cent further than in the case where only conduction is acting above and below the ignited interval. INTRODUCTION In the theoretical treatment of forward combustion in a radial system, one of the problems encountered is the determination of the transient temperature distributions caused by an expanding cylindrical heat source. Bailey and Larkin' and Ramey' simultaneously presented analytical solutions to the problem assuming heat transport by conduction alone. In a subsequent publication, Bailey and Larkin3 included the effects of both conduction and convection while treating linear and radial models. In this latter work, however, vertical heat losses were largely neglected. Selig and Couch' dealt with a radial model in which both conduction and convection were acting. Only a limiting case involving vertical heat losses was considered, however. Namely, temperatures on the boundary of the bed of interest were set equal to zero. Solutions thus obtained were representative of a system having a maximum vertical heat flux. Chu5 recently treated a more general case in which a permeable bed was considered bounded by impermeable media. Conduction and convection took place within the bed, and only conduction outside of the bed. The effects of vertical heat losses were included in his study. Solutions were obtained by numerical techniques. This paper is an extension of the theoretical work of other authors pertaining to forward combustion in a radial system. In particular, a mathematical model of the process is treated in which heat generation occurs over a small vertical interval of a larger permeable section. In the interval supporting heat generation, and above and below this interval, the mechanisms of radial conduction and convection are also presumed acting. Heat losses from the ignited interval are accounted for by vertical conduction. An analytical solution for the temperature distribution caused by radial movement of the burning front is presented. The effects of certain process variables are indicated and comparisons with Chu's results are made. THEORY To render the mechanism of forward combustion tractable to mathematical treatment, we idealize the problem to the extent of assuming continuous reservoir media possessing homogeneous and isotropic properties. The following additional assumptions are implicit in this analysis. 1. The thermal parameters, i.e., heat capacities, thermal conductivities and thermal diffusivities are invariant with temperature and pressure. Moreover, the bounding media possess the same thermal properties as the bed of interest. 2. The temperatures of the porous media and its contained fluids at any point and at any time are equal. 3. The reaction rate between the oxidant gas and the fuel is infinite. This assumption implies that the incoming oxygen concentration instantaneously goes to zero within an infinitesimal distance, i.e., the width of the combustion zone is negligible. 4. The rate of gas injection is constant and corresponds to the average rate throughout the lifetime of the project. 5. The fuel concentration is constant throughout the volume of rock swept out by the burning zone. 6. There is complete burnoff of fuel. This assumption demands that the rate of propagation of the burning front equals the rate of fuel burnoff. In a radial system, with a

By A. U. Seybolt

The solubility of oxygen in a iron has been determined in the range between 700° and 900°C. The solubility is a function of temperature and varies from about 0.008 pct oxygen at 700°C to atureandabout 0.03 pct at 900°C. The heat of solution is approximately +15,500 cal per mol. AS pointed out in a recent paper by Kitchener et al.,1 there has been a lack of agreement among many investigators even as to the order of magnitude of the solid solubility of oxygen in the various forms of iron. This lack of agreement is attributable in large part to the difficulties in the determination of a small oxygen solubility; but because the problem has remained so long unsettled, it also indicates a lack of interest which is rather surprising when the demonstrated importance of small amounts of soluble nonmetallic impurities in iron is considered. The work of Kitchener et al. apparently leaves the solubility of oxygen in iron in a satisfactory state, but no attempt was made to investigate the solubility in a iron. The solubility of oxygen in a iron is actually of greater interest, since it is in this form that iron and mild steels are employed ordinarily. That the effect of oxygen in iron is of more than theoretical interest has been well established by Fast,' and more recently by Rees and Hopkins," who demonstrated that oxygen in the range between 0.0008 and 0.27 wt pct has a pronounced effect upon the mechanical properties. Previous Work and Methods Used To report in detail the literature relating to the solubility of oxygen in a iron would require an inordinate amount of space. For those interested in reviewing this work, a bibliography4-13 of the more significant papers is appended. In general, two methods of studying this problem have been used. One is the gas-metal equilibrium method where the H2O-H2-Fe or the CO2-CO-Fe equilibria have been used. The other is the more direct approach of the oxidation of thin strips of pure iron by packing in mill scale or by air or gaseous oxygen at some desired temperature. In this method oxygen is allowed to oxidize the surface and then to diffuse inward until saturation is obtained. In the gas-metal equilibrium method the oxygen dissolved in solid iron at a given temperature is proportional to the ratio of the water vapor-hydrogen pressures or the CO2-CO pressures over the sample for small ratio values. If the ratio becomes higher than a critical value, then an oxide phase makes its appearance (the solution becomes supersaturated). In principle, it is possible to use a series of H2O/H2 or CO2/CO ratios and to find by analysis the corresponding amounts of oxygen in solid solution at constant temperature. At the point where a very small increase in the gas ratio (increase in oxidizing powder) produces a large increase in oxygen content, the solid solubility limit is reached. Alternately, if the critical ratio is known, it is possible to use the procedure of Kitchener et al.1 and to use a ratio which is near but below the critical one. The solubility corresponding to this lower ratio will not be the saturation solubility at the temperature employed, but the saturation solubility can be calculated by multiplying the measured solubility by the critical ratio over the ratio used. However, in the case where oxygen gas is the oxidizing medium, the saturation solubility is not a function of pressure, providing the pressure exceeds the dissociation pressure of FeO in equilibrium with iron. This is 1.2x10-16 mm at 800 °C, according to Dushman." As pointed out by Darken17 in discussing the FeO phase diagram, most of the possible errors tend to yield high values of oxygen solubility. For example, one circumstance which evidently caused the reporting of many high values was the use of finely divided or powdered iron in the gas equilibrium method. Because of the large surface area of such a sample, and the likelihood of some surface contamination if only by exposure to air, the results tended to be high. The direct oxidation method which was used in this work has the advantage in that it is simple and direct, but it suffers from one disadvantage: equilibrium can only be approached from the low oxygen side. The important factors to be kept under control are the following: 1—use of high purity iron to avoid internal oxidation (oxidation of readily

Jan 1, 1955

By B. J. Kochanowsky

The idea of a portable crusher is not new. Many such crushers are available but they are small and designed for construction work. For many years the author has suggested, both in this country and in Europe, the building of larger portable crushers intended expressly for use in quarries or open pits. Although not applicable under all conditions, there are mining operations where a mobile crusher arrangement could be more profitable than the facilities now used. The primary use of a portable crusher, i.e., a crusher mounted on crawlers or tires, in the rock and mining industries is to reduce costs by permitting the substitution of conveyor belt haulage for truck or track haulage. The usual sequence of operations in surface mining is drilling, blasting, loading, haulage, and crushing. Haulage is normally accomplished by truck or track-mounted cars, the latter method being used for the longer distances. However, by using a portable crusher in the pit, the sequence of operations would be changed so that the crushing stage would occur before haulage (Fig. 1). Such a sequence would permit the use of conveyors to replace the more expensive truck or track haulage methods. Since most quarry and open pit operations normally require a crushing stage, the only additional costs incurred will be due to the investment required to purchase or construct a mobile arrangement for a crusher. But this factor has to be weighed against the advantages to be gained by conveyor haulage. As shown in Fig. 2, transportation of material by belt conveyor over short distances is less expensive than by truck. The inclination of the belt has no effect on belt speed; consequently, the hourly tonnage moved remains the same. Conversely, the output rate of trucks as expressed in tons or ton-miles per shift decreases proportionally to the haulage speed, which is considerably slowed by the steepness of the road (Fig. 3, left). Although maximum possible grades and maximum economic grades of haulage are greater for a belt than for a truck (over the same total lift), the longer haulage distances favor the use of trucks. Although power consumption for hauling on a grade increases for both conveyances, the rate of power consumption increases faster for trucks than for conveyor belts (Fig. 3, right). Since the output rate and related fixed costs are affected by the travel speed, total haulage costs with trucks would increase with the grade more rapidly than the similar costs of conveyor belts (Fig. 4). Travel distance, road grade, speed, size and number of pieces of equipment, efficiency of operation, and many other factors affect such haulage costs. In general terms it can be said that the shorter the distance, the steeper the grade, and the greater the output, the more advantageous the belt becomes in comparison to truck or track haulage. In addition to potential cost savings in haulage procedures, a portable crusher would allow better utilization and performance of shovels. Loading operations would not be interrupted as often by the necessity of waiting for cars or trucks. Unfortunately, the application of belts in open pits for haulage from bench sites is generally not practical under existing conditions because a belt fed directly by a mechanical shovel can be torn, damaged, or worn out quickly by the large rock fragments falling on it during loading. However, by using a mobile crusher this situation can be avoided. As shown in Fig. 1 (b), the shovel feeds rock into the crusher located behind it. The crushed material is initially transported by an extensible and/or movable belt, thence by a longer stationary conveyor to the plant where the material is subjected to further treatment by secondary crushing, screening, etc. The first-mentioned conveyor, needed to bridge the distance between the shovel and the stationary conveyor, is necessarily variable in length owing to the continuous movement of the shovel and the desire to keep the stationary belt at a safe distance from the bench during blasting operations. The remarkable part of mobile crusher operations is the extra-ordinarily high output per man-shift, the low maintenance and power requirements for haulage, and the increased output of the loading shovel. A cement quarry which has been using a portable crusher and conveyor since 1956 requires only three men to operate the shovel and crusher and to transport the crushed rock by belt from the quarry face to the screening plant. If truck haulage

Jan 1, 1961

By P. A. Witherspoon, R. W. Donovan, T. D. Mueller

The use of petroleum-barren aquifers for underground storage has become extremely important to the natural-gas industry. A critical problem in assessing the feasibility of a specific aquifer for such use is the permeability determination of the caprock over the proposed storage project. The approach used here is to conduct both static and dynamic field tests on the aquifer being analyzed. Valuable information on the possibility of communication between the storage aquifer and any other aquifers above can be obtained by measuring hydrostatic water levels and water analyses. Significant differences in such data give evidence of the lack of communication between the intended storage reservoir and other horizons. The dynamic approach requires that one well be pumped in the storage aquifer, and changes in fluid levels recorded in both the aquifer and its caprock. The interpretation of the data from such pumping tests involves the solution of nonsteady radial flow in an infinite aquifer and the influence on such flow of a leaky caprock. A finite-difference model has been used to investigate this problem, and the transient behavior has been solved numerically with a digital computer. It has been found that the pressure transients in the storage aquifer are not affected significantly by moderate caprock leakage. The pressure behavior of the caprock is a much better indicator of the degree of leakage, and generalized solutions for this behavior are included. Field data are presented to demonstrate both the static and dynamic approach. If is concluded that appropriate investigation of the groundwater hydrology in an aquifer-type gas-storage project can provide much valuable information for determining the effectiveness of the caprock to hold gas. INTRODUCTION Underground storage of natural gas in the United States has been developing at a rapid rate over the past few years. In 1955, the total gas-storage capacity was about 1.6 trillion cu ft; by 1961, this figure was almost 3.2 trillion cu ft, an increase of 100 per cent in six years.' This trend un- doubtedly will continue because the economics favor the development of gas storage, as opposed to the construction of new pipelines, to meet the inherent cyclic demand for fuel in the metropolitan areas of this country.' About 15 per cent of the current underground gas storage has been developed in petroleum-barren aquifers, i.e., geological domes or anticlines in which no commercial quantities of oil or gas had been produced prior to the storage operations. The necessity for using barren aquifers outside many metropolitan areas of this country has been due to the lack of depleted oil or gas fields that were near enough and large enough to meet the demands of such consuming areas. Pipeline companies have developed aquifer storage along their transmission lines to meet the fluctuating needs of their complex systems. Considerable thought has also been given to the problem of storing gas in a structureless aquifer, both in this country' and in the Soviet Union outside the city of Leningrad.'," Conditions such as these have led to the development of aquifer gas-storage projects in many parts of the U. S. Most of these developments have centered in the Mid-Continent area, and the greatest amount of activity has been concentrated in Illinois.6 Thus, the use of petroleum-barren aquifers for gas-storage purposes has become extremely important to the natural-gas industry. There are three basic problems in developing aquifer-type storage: (1) finding an adequate geologic structure, (2) finding a suitable storage reservoir within the structure and (3) determining the tightness of the caprock over the intended storage zone. The first two problems can be solved by applying conventional methods of exploration geology, but once these problems are solved, the question arises as to why no oil or gas is present in an otherwise favorable setting. Two situations are possible: (1) an adequate source bed was never present, or (2) a source bed was present but the petroleum seeped away because of a leaky caprock. Determining the tightness of the caprock is one of the most critical problems in assessing the feasibility of a specific aquifer for storage purposes. In attacking this problem, one usually takes cores of the caprock and subjects them to a rigorous investigation. Such core data are desirable, but they only detail the matrix properties and cannot be expected to reveal the gross characteristics of the caprock. Several gas-storage projects in the U. S. have had considerable leakage where

By D. E. Thomas, C. E. Birchenall

ALTHOUGH Eoltzmann gave a mathematical solution for the diffusion equation (for planar diffusion in infinite 01. semi-infinite systems only) in 1894 allowing for variation of the diffusion coefficient with a change in concentration, it was not until 1933 that this solution was applied to an experimentally investigated metallic system. The calculation was carried out by Matano' on the data obtained by Grube and Jedele3 for the Cu-Ni system. Since that time concentration dependence of the diffusion coefficient has been demonstrated for many pairs of metals. However, the nature of this dependence has never been fully elucidated. Many investigators have suspected that these variations could be related to the thermodynamic properties of the solutions, one of the earliest explicit statements being contained in a discussion of irreversible transport processes by Onsager' in 1931. Development along these lines has been greatly retarded by the lack of reliable data on the variation of tliffusivity with concentration, the paucity of the thermodynamic data for the same systems at the same temperatures and compositions, and an incomplete understanding of the relation of the thermodynamic properties of the activated state for diffusion to the bulk thermodynamic properties. The last factor has been discussed by Fisher, Hollomon, and Turnbull.5 In many instances where data exist, it is difficult to know which are acceptable. This problem probably applies more strongly to diffusion data than to activity measurements. For instance, four sets of observers"-" have reported self-diffusion coefficients for copper. The average spread between extreme results is a factor of about four, though the individual sets of data are self-consistent to about 20 pct. Thus one or more factors are out of control, at least in these experiments, making estimates of internal error unreliable. The most reliable diffusion data in most systems have resulted from the use of welded couples with a plane interface from which layers for analysis are machined parallel to the interface after diffusion. The layers are analyzed, and the result is a graphical relation between distance and concentration, usually called the penetration curve. Given the same set of analytical data and distances and following the same procedure in computation, different observers will generally produce diffusion coefficients which vary appreciably, especially at the extremes of the concentration range. Experiments must be carefully designed so that the precision is good enough to answer a particular question unequivocally. In the first calculation of the dependence of the diffusion coefficient on concentration in the metallic solid solution Cu-Ni, Matano found that the coefficient was insensitive to concentration from 0 to 70 pct Cu, after which it rose more and more steeply to some undetermined value as pure copper was approached.' The same behavior was reported for Au-Ni, Au-Pd, and Au-Pt.* The data used were those of Grube and Jedele which were very good at the time, but are not considered particularly good by present standards. Furthermore, the method of calculation makes the ends of the diffusion coefficient-concentration curve unreliable. For better reliability, the high copper end of the curve has been checked by incremental couples, where the concentration spread is 67.7 to 100 atomic pct Cu. The implication of the curves calculated by Matano was that diffusion is very concentration sensitive in one dilute range of this completely isomorphous system and hardly at all in the other. Matano's result is confirmed. Later Wells and Mehll0 published data on diffusion in Fe-Ni at 1300°C, which represent a thorough test of the shape of the concentration dependence curve. They ran couples with the following ranges of nickel concentration: 0-25 pct, 1.9-20.1 pct, 0-20.1 pct, 20.1-41.8 pct, 0-99.4 pct, and 79.3-99.4 pct. Although the trend of the data indicates an S-shaped concentration dependence, their curve was drawn to the pattern set by Matano. Their original data have been recalculated for the 0-99.4 and 79.3-99.4 pct couples. Wells and Mehl's points and two independent recalculations from the raw data are plotted in Fig. 1. What appears to be the best curve is drawn through them. This curve shows little sensitivity to composition in both dilute ranges with a strong dependence at intermediate composi-tions.? Similar experiments on the Cu-Pd system are reported here at temperatures where solubility is unlimited. These lead to the same type of concentration dependence for the diffusion coefficients as was found upon recalculation of the data for the Fe-Ni system. Experimental Procedure Cu-Pd: The concentration dependence of the diffusion coefficient may be determined by the use of

Jan 1, 1953

By Thomas C. Wilder, Walter E. Galin

Measurements of the electromotive force of the cell at 995°C have shown that the cell may be used to detennine the zinc content of molten Cu-Zn alloys to the nearest 0.05 wt pct. The cell is used for brass melts to which no ZnO is added intentionally, because essentially all oxygen in the Cu-Zn-O system is present in the form of ZnO. The cell is also used to detev,nine the thernodynamic activity of zinc for Cu-Zn al1oys of the brass composition range, from which the equilibrium partial pressure of zinc for such alloy may also be calculated. The electrochemical measurement of the concentration of the most active metal in other engneering- alloy systems by a similar technique is also considered. IN recent years there have been many studies concerning the direct electrochemical measurement of oxygen content in molten engineering metals.' These investigations employ galvanic cells in which the electrolytes are various solid mixed-oxides which conduct current by movement of oxide ion vacancies under the influence of an oxygen potential gradient. Similar cells have also been used to measure the thermodynamic properties of mixing of solid alloys,' one component of which has a much greater affinity for oxygen than the other component(s). One alloy system of obvious engineering importance comprised of two metals of greatly differing affinity for oxygen is copper-zinc. At the casting temperature of molten brasses, the zinc concentration is very difficult to control not only because its vapor pressure is very high, but also because of its high affinity for oxygen to form ZnO. Inasmuch as brass castings may be required to have a zinc concentration within very narrow limits, it would be advantageous for the brass industry to have a means for quickly measuring the zinc content in the molten alloy just prior to pouring. A calculation based on earlier thermodynamic studies of oxygen and zinc in dilute solution in binary Cu-O and CU-Z' alloys indicates that the oxygen concentration of molten 70 wt pct Cu-30 wt pct Zn brass must be much less than 1 ppm for the separate phase ZnO not to exist in the ternary Cu-Zn-O system. Thus it can be assumed that all molten brasses, both in the laboratory and in the foundry, are sufficiently saturated with oxygen for the separate phase ZnO to be present. In view of the foregoing reasons, the cell investigated at 995°C for the purpose of measuring the zinc concentration in molten copper-zinc alloys, particularly those of brass compositions. In this cell the left hand electrode is a reference electrode comprised of a mixture of the pure powders of nickel and nickel oxide, to which a platinum contact is made. The electrode of interest is a molten Cu-Zn alloy of unknown zinc concentration with a tantalum wire contact. The electrolyte is the commercially available (Zircoa) calcia stabilized zirconia. The ZnO in the Cu-Zn electrode compartment is not intentionally added, but is naturally present as a result of the infinitesimal amount of oxygen required for its formation in this alloy system. In cell [A] nickel oxide is reduced at the cathode where O= represents the electrolyte. At the anode dissolved zinc of the Cu-Zn alloy is oxidized to form ZnO(s) in its standard state Thus the overall reaction is for which the molar free energy change is where 5 is the Faraday equivalent (23,063 cal per v equivalent), is the electromotive force of the cell in volts after correction for the Pt-Ta thermocouple, FOf (ZO) and AFF (NO) are the standard molar free energies of formation of the respective oxides, and a2n is the thermodynamic activity of zinc in the molten Cu-Zn alloy. The reference state of zinc in this case is taken to be the pure liquid. At constant temperature all the terms of Eq. [I] are constant except and azn Thus since all other participants in the electrochemical reaction are in their standard states, the change in the electromotive force of Cell [A] is represented only by a change of the thermodynamic activity of zinc at constant temperature. The zinc concentration is related to the activity by sampling the alloy for chemical analysis after cell measurements are taken. EXPERIMENTAL A typical cell construction is shown in Fig. 1. This and other experimental details were similar to that described earlier with the exception of some minor modifications which are detailed below.

Jan 1, 1970

By R. T. DeHoff

A theoretical development is presented which reformulates Fick's first law for diffusion in the solid state. The diffusion flux of component i in a multi-component system, Ji, is related to its local concentration, ci, and local jump frequency, ri : where a is a geometric factor and d is the jump distance. The product, ciri , is defined as the local concentration of atomic jumps for component i. The analog to Fick's second law is also derived. A solution to this equation is presented, which permits the experimental determination of the variation of atom jump frequency with composition in multicomponent systems. HISTORICALLY, the description of diffusion in the solid state has been presumed to be best approached as an application of more general diffusion laws, known as the phenomenological equations. These equations relate the flux, Ji, of the various components, expressed in atoms, grams, or volume, to the driving force involved, expressed as either a compositional or chemical potential gradient, sumption that the flux is simply proportional to the driving force is the foundation of this approach. The phenomenological equations take the form: where the concentration gradients are assumed to be the driving force, and: if the chemical potential gradient is taken as the driving force. The coefficients Dij in Eq. [1.] are the "diffusion coefficients"; the elements of the corresponding matrix in Eq. [2], the Mij, are called the "mobilities". Eqs. [I] and [2] may be considered to be definitions of these phenomenological coefficients. A formidable body of literature has been generated about these equations; this literature dates back to their original formulation for the simplest case of binary diffusion in a fluid, by Adolf Fick, in 1855.' This description has been shown to be self-consistent. However, the "constants of proportionality", the Dij or ,Mij, are not constant: they vary with composition in all but the simplest systems. Even in the case of tracer diffusion, wherein it can be shown that the diffusion coefficient is constant, the mobility, which is considered in irreversible thermodynamics to be the more physically meaningful quantity, varies with the concentration of the tracer involved.' In more complex systems, it is necessary to evaluate the entire matrix of phenomenological coefficients, as a function of composition, in order to describe diffusion locally. Further, in order to determine this matrix experimentally, it is necessary to produce diffusion couples that have different sequences of compositions; the matrix may be evaluated only at points where these "composition paths" cross.* Finally, and perhaps most

Jan 1, 1969