Search Documents

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By Robert D. Pike

In November 1939, on behalf of the Harbison-Walker Refractories Co., the author undertook the study of the problem of utilizing the dolomite of northwestern Ohio for the manufacture of calcined magnesia suitable for use in refractories. Grateful acknowledgment is made of the unfailing assistance and encouragement throughout this work from the executive and technical staff of Harbison-Walker Refractories Company. The dolomite of the Niagara formation that is exposed or near the surface of a wide area in northwestern Ohio1 constitutes a vast supply of almost pure dolomite. It offers a virtually unlimited supply of cheap raw material of uniform dependable analysis for the manufacture of magnesia. A typical analysis of dolomite from the vicinity of Luckey, Ohio, follows: Stone Completely Calcined CaO(Sro)a............. 30.35 57.806 Mgo................... 21.55 41.050 SiO2. ................... 0.30 0.572 R2O3................... 0.30 0.572 Ignition loss............. 47.50 a SrO about 0.06 pct. Brines containing magnesium chloride or sea water can be reacted with calcined dolomite to produce magnesia.2'3 In such reactions the MgCl2 of the brine supplies some of the magnesia and the amount of dolomite required is thereby reduced by an equivalent amount, but brines of commercial importance containing magnesium chloride are some distance away from the purest grades of the dolomite of northwestern Ohio. It was decided therefore to concentrate upon the development of a suitable process for separating the lime and magnesia of dolomite, depending upon the dolomite itself as the sole source of magnesia. This would make it possible to place a plant at the dolomite quarry, thus eliminating the cost of transporting the stone and also rendering the calcined magnesia available at a most convenient production point, considering the cost of delivery throughout the steel industry. The selection of a process depending solely upon the dolomite as a source of magnesia also necessarily entails production of the lime content of the dolomite as a by-product. It was recognized that if such a lime by-product could be produced in a suitable form, a plant location in northwestern Ohio would also be advantageous for marketing the lime. The problem, therefore, was the discovery and development of a low-cost process for separating the magnesia and lime of the dolomite of northwestern Ohio and producing each in a form relatively free from the other, and meeting the respective requirements of established markets. A satisfactory solution of this problem has been found, and it is the

Jan 1, 1948

By R. J. Arsenault

The yield drop that occurs in tantalum, Cu-AZ. and Ag-Al was investigated as a function of strain rate and at several temperatures. From the strain-rate dependence of the yield drop an activation volume was calculated and found to agree with that obtained from differential strain-mte tests. The temperature dependence of the yield drop can he explained in terms of the parameter temperature divided by activation volume. The yield drop is attributed to the rapid multiplication of dislocations during their motion. THE yield-point or yield-drop (upper yield stress minus the lower yield stress) phenomenon has been the subject of numerous investigations1-9 in both bcc and fcc metals. Also, there is no dearth of theoretical explanations10-20 to account for the yield-point phenomenon. The present explanations can be divided into two categories: the concept of dislocation locking and subsequent unlocking and the concept of multiplication of dislocations due to their motion. The Vottrell10,11mechanism of locking and unlocking, as applied to bcc metals, is the best known of the three proposed locking mechanisms. The two additional mechanisms, short-range order (SRO)7,16,17 and Suzuki-type locking,14,15 have been employed to account for the existence of yield points in fcc metals. The experimental evidence supporting the locking of dislocations, especially in bcc metals, is well-established. The dependence of the yield point on interstitial concentrations,' the kinetics of strain aging,2 and the observations by electron-transmission microscopy18 are some of these experimental results. The number of experimental observations supporting dislocation locking in fcc metals is not as extensive as in bcc metals. The unlocking of dislocations, which actually is supposed to account for the yield drop, is by no means well-established by experimental results for either bcc or fcc metals. The similar temperature dependence6 of the yielding and plastic flow is one of the experimental factors that cannot be explained in terms of the unlocking of dislocations. The mechanism based on the rapid multiplication of dislocations has been proposed by several investigators. 18-20 Johnston and Gilman19 have proposed a detailed model of yielding, which was later employed by Hahn21 to predict quantitatively the yield drop in iron. This mechanism was discussed in a previous paper22 and several limitations were pointed out. In the same paper it was shown that an activation volume could be obtained from the strain-rate dependence of the yield drop and that a correlation existed between the activation volumes obtained from the yield-drop tests and from differen-

Jan 1, 1964

By M. S. Azun

M.S. Azun I have many objections to the content of the author's paper. Before discussing it, however, I would like to repeat the property of semivariogram function. Second order stationary properties of regionalized variables (ReV's) such as semivariogram function ?(h) are perfectly known in geostatistics. Also, the kriging equations in the language of mathematical statistics using second order stationary properties are well understood. However, the way to use the sample (estimated) semivariogram function in any one of the kriging procedures is vague. The sample semivariogram function is given as follows: [1 N-hy*(h) = 2(N h) i21 {Xi-Xi+h}Z, h=0, 1, N-1] where N is the total number of samples, Xi is the sample value at the i - th location, X i+h is the sample value at the i +h - th location, and h is the distance among the samples. An estimation variance of sample semivariogram function of first lag is smaller than that of higher order lag. The theoretical semivariogram function reaches the variance of samples asymptotically. But this is not easily observable because of the larger variation involved in the estimate of semivariogram function. In general, an estimation procedure is done for h = 0, 1, 2,…., up to the greatest integer less than N/2, even though sample semivariogram function can be computable through N-1. After estimating semivariogram function, the critical question of how to model sample semivariogram function arises. As seen in the above equation, sample semivariogram function is discrete and can be smoothed by the model being selected. Therefore, modeling of sample semivariogram function is the most important step in geostatistics. It not only smoothes a discrete function but also affects the results of the kriging procedure. When the only aim is to model the semivariogram function, which is the basic point of the author's paper, one can employ any fitting techniques, such as curve fitting, or any ar¬bitrary functions, which are called submodels in the paper. The term "arbitrary function" is used rather than "submodel" because there is no basic understanding of developing them. The author suggests that the sum of those submodels can also be used for the modeling of sample semivariogram function. The combination of any arbitrary functions brings many problems instead of giving an insight of the domain structure considered. The author used two arbitrary functions and the nugget effect in response to sample semivariogram function (Fig. 10). For the same example, he stated that the parameters involved in the mixed arbitrary function model can be accepted when the discrepancy between sample semivariogram function and the model is small visually. For verifying the fitting behavior of any selected model, one should not be contented with the visual satisfactory. Some statistical measure such as goodness of fit has to be used. The author's practice is no more than an exercise in curve fitting without any fundamental understanding or conceptualization of the underlying physical mechanism. Furthermore, the selection of any model is not an easy task if the purpose is the search for the "best" response to the observed second order properties of ReV's. I suggest that the Markovian model (Azun, 1983), on the basis of a theoretical understanding of underlying mechanism, which gives more information about the occurrence of regionalized variables, is used to respond all properties of ReV's. There are a lot of problems for modeling of onedimensional sample semivariogram function. Thus, it is not appropriate to go to higher order dimensional sample semivariogram function modeling. In the meantime, I would recommend that one can connect the values of standardized sample semivariogram function rather than simple values of semivariogram function in the two-dimensional estimation. The standardized values can be computed in dividing the semivariogram function value by the number of sample pairs involved in each lag regardless of the directions. In conclusion, geostatistics is an interdisciplinary area in mining that uses the principles of mathematical statistics. Thus, it should not violate any probabilistic and statistical rules. When Matheron was developing the theory of geostatistical study in the early years of geostatistics, many mining people had a reservation accepting the geostatistical tools. However, this does not mean that we, the geostatisticians, might try to convince those people using some "strange" tools or rules as some authors implied (Baafi and Kim, 1984). Instead, we have to develop and explain the geostatistical tools staying only in the framework of statistical concepts and properties. ? References Azun, M.S., 1983, "Stochastic Process Modeling of Spatially Distributed Geostatistical Data," Columbia University, Ph.D. Thesis. Baafi, E.Y., and Kim, Y.C., 1984, "Discussion - Comparison of Different Ore Reserve Estimation Methods Using Conditional Simulation," Mining Engineering, Vol. 36, No. 3, p. 280. Reply by J.M. Rendu The interactive method proposed by Rendu allows practitioners to develop semivariogram models that take into account not only the numerical information obtained by sampling, but also highly significant additional information that often cannot be quantified. The geology of the deposit - including hypotheses concerning its genesis, sampling methods, assaying methods, and mathematical methods used to calculate the semivariograms - all have an influence on the numerical results obtained and on how these results should be interpreted. If all the information concerning the spatial distribution of values in a mineral deposit was contained in the sample values, it could be argued that statistical techniques alone would produce optimum models. However, this is rarely, if ever, the case. Methods that allow the user to take into account his experience and his geologic understanding of the deposit should not be rejected for the sake of theoretical statistical purity. ?

Jan 1, 1986

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By J. B. Conway

RECENT studies of first-stage creep data have led to a special least-squares procedure for use in calculating the Andrade creep-equation constants. This procedure is easy to apply, uses only experimental data, and yields results which do not vary with the individual making the analysis. Taking logarithms of the Andrade equation I = lo(1 +ßl1/3)ekt leads to In l = In lo + In(1 + ßl1/3) + kt A residual can then be defined as the difference between the logarithm of an experimental length value and the logarithm of a calculated length value. Following the usual least-squares approach differentiation with respect to 10 and k of the expression for the sum of the squares of the residuals leads to two equations which cannot be solved directly for the three constants involved. However, values of ß can be assumed and corresponding values of lo and k can then be calculated. Then the sum of the squares of the residuals can be calculated. For a certain value of ß this sum will exhibit a minimum value to identify the least-squares values for ß, lo, and k. An illustration of the application of the above least-squares approach is obtained by employing the creep data for lead originally presented by Andrade' in the development of the one-third creep law. A plot of the sum of the squares of the residuals as a function of ß is shown in Fig. 1 along with the corresponding lo and k values. The minimum is seen to occur at ß = 0.0143 from which lo = 39.149 and k = 7.27 x 10-5. Based on these results the Andrade equation for these lead data is 1 = 39.149(1 + 0.0143 t1/3)e7.27 x 10-5t compared to the equation I = 39.13(1 + 0.01457/l/3)e6.95 X 10-5t developed by Andrade (calculation procedure not given but was probably a graphical solution). Calculating length values using the above equations and comparing with the experimental length values, residuals corresponding to the difference between experimental and calculated length values can be obtained. The sum of the squares of the residuals can then be calculated. For the case of the least-squares approach a value for this sum was found to be 2.37 x 10-3 compared to a value of 3.47 x 10" for the equation originally proposed by Andrade. In other words, while the constants proposed by Andrade provide an excellent fit for the lead data, a still better representation is afforded by applying the least-squares approach discussed above. A similar result was obtained for the lead data at 162oc.l The least-squares approach led to 1 = 9.866(1 + 0.0497 t1/3)el.011 x 10-2t compared to the equation I = 9.94(1 + 0.0433 l1/3)e1.06 X 10-2t given by Andrade. In this case, too, the sum of the squares of the residuals is slightly smaller for the equation based on the least-squares approach. It should be pointed out that a double trial and er-

Jan 1, 1965

By Robert Wamsley, W. E. Jones

ONE of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available, because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide, about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers. The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at-Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1945

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By John G. Tate, George W. Nicolson, James L. Bruce

For more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.' From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. Description of Ore Bodies The shape Of the Ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions) extending from unknown depths below the bottom level at elevation 250 ft below sea level) to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the Ore body extended to surface and was Mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the Ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upper-side of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and Clay sedimentaries of Miocene and later age, The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-Stained by the descending meteoric waters, It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pet Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pet. on the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main Ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. 'This probably can

Jan 1, 1949

By D. H. Davis, I. Fatt

Oil bearing rocks, usually found at depths of 2,000 to 10,000 it, are elastically deformed by overburden pressure. Although the change in porosity with pressure in a number of example rock.: has been shown to be small, it was thought that overburden pressure might have a significant effect on permeability. This note presents results of an investigation to determine the magnitude of the change in permeabilty with pressure. In routine core analysis permeabilities are measured on rock samples which are not under overburden pressure. If permeablity measured in this way differs from permeabilities measured under overburden pressure, a systematic error is introduced into well productivity calculations. The experiments described in this report were made to determine the magnitude of the change and thus to give an estimate of the error introduced into the calculations. The error introduced by the neglect of the change in permeability when overburden pressure is removed may account for part of the difference between well productivity calculated from core analysis and the actual well productivity. The results obtained in this investigation have only quali-tative significance because of the difficulty in reproducing in the laboratory the stress conditions on the rock buried in the earth. The assumption which is usually made is that the rocks in the earth are under a uniform pressure equal to the weight per unit area of the vertical overburden column from the rock in question to the surface of the earth less the pressure of the liquid in the pores of the rock. For an overburden consisting of sandstones and shales (of assumed average specific gravity of 2.3) and for a liquid pressure equal to the pressure in a salt water column (of specific gravity 1.0) reaching from the rock to the surface, the resulting net pressure on the rock is approximately 0.56 psi per ft of depth. EXPERIMENTAL METHOD Clean, dry sandstone core plugs one in. in diameter and about three in. long were mounted in a copper foil jacket as shown in Fig. 3 or molded in a Lucite jacket as shown in Fig. 4. All cores except those labeled "2" in Fig. 1 and "8" in Fig. 2 were measured in the copper foil jacket. Cores "2" and "8" were measured in the Lucite jacket. The jacketed core was placed in a high pressure hydraulic bomb in which the liquid pressure outside the jacket could be raised to 15,000 psi. Flow lines from the core were brought out of the bomb through special fittings in the bomh head and connected to a laboratory type gas permeameter. Measurements were made with nitrogen gas; the maximum mean gas pressure in the core was 16.1 psia. RESULTS The specific permeability of sandstone decreases with in. crease in overburden pressure. Most of the decrease takes place over the range of zero to 3,000 psi overburden pressure. If the net pressure on the rock is assumed to be 0.56 psi per ft of depth as discussed above, 3,000 psi of overburden pressure is equivalent to about 5,000 ft of overburden. At 3,000 psi overburden pressure, the permeability of the eight sandstone core samples tested ranged from 59 to 89 per cent of the permeability without overburden pressure. Figs. 1 and 2 show the permeability reduction as a function of overburden pressure. The permeability of the eight cores without overburden pressure ranged from 4.35 md to 632 md; these permeabilities are listed in Figs. 1 and 2. REFERENCES 1. Carpenter and Spencer: "Measurements of Compressibility of Consolidated Oil Bearing Sands," U. S. Bureau of Mines, R.I. 3450, (1940). * * *

Jan 1, 1952

By M. T. Hepworth, W. B. Sample

HYDROGEN solubility and linear contraction measurements were made at constant temperature on an alloy of titanium of constant oxygen-to-titanium molal ratio but variable hydrogen content. A cylindrical specimen of titanium (0.25 by 1.6 in.) containing 0.75 at. pct 0 and less than 0.03 at. pct N was cast from a master button of iodide process titanium which had been alloyed with titanium dioxide. Four vacuum fusion analyses, which were made along the length of the cylinder after the hydrogen solubility studies were made, revealed a variation of oxygen content of less than 0.02 at. pct. The specimen was introduced into a quartz furnace tube, annealed and outgassedat 1050"~ for about 1 hr, and then held at 800" * 0.5" for about 30 hr, during which latter time experimental data were taken. The leak rate to the furnace chamber was not sufficient to contaminate the specimen during the run as determined by leak-rate studies and vacuum fusion analyses for oxygen and nitrogen before and after the runs. The furnace chamber was attached to a modified Sieverts apparatus used to introduce measured quantities of purified hydrogen to the specimen. A quartz pushrod transmitted changes in length of the specimen to a Chevenard dilatometer. The push-rod passed through a vacuum grease seal to the dilatometer which amplified motion of the rod by a factor of 319. During hydrogen addition, the pushrod did not contact the specimen. Measured quantities of hydrogen were added to the specimen and equilibrium hydrogen pressures recorded as a function of hydrogen content. The solubility data, which appear in Fig. 1, agree well with a separate investigation made with a different apparatus. The solubility limit of the hcp a phase appears as an abrupt discontinuity in slope at 3.4 at. pct H. The solubility plot has been extended as a dashed line at this discontinuity in order to emphasize the discontinuity. The hydrogen content at which bcc P appears is not clearly defined. An arrow indicates solubility data were taken upon hydrogen addition. Upon reaching the arbitrary maximum hydrogen content of the run, the quartz pushrod was pressed against the specimen in order to record the change in length with hydrogen removal. A pressure of about 100 g per sq cm was required to overcome the friction of the vacuum seal in order to obtain reproducible linear contraction data. The contraction ratio ~2/1", change in length divided by original length, was set equal to zero for the maximum hydrogen content. The relative contraction of the specimen was observed upon removal of hydrogen in the following manner. The system was opened to the pumps for a few seconds and an unknown quantity of hydrogen was removed. The system was then isolated from the pumps by closing a stopcock and allowed to return to equilibrium. When the temperature returned to 800°C, the pressure stabilized, and contraction ceased, measurements of contraction and pressure were made. The hydrogen content of the specimen was then deduced by measuring the equilibrium PIydrogen pressure and referring to the solubility plot. Linear contraction was then plotted against interpolated values of atomic percent hydrogen. The justification for this procedure is the established reversibility of the hydrogen equilibrium.' Uniaxial compression was assumed to have no effect on hydrogen pressure. The isothermal linear contraction data are plotted on Fig. 1. An arrow indicates data were taken upon removal of hydrogen. The solubility limits of the two phase a i /3 region can be identified by discontinuities ill slope of the dilatometric plot at 9.1 and 3.4 at. pct H, agreeing well with other studies.' Dashed extensions of the plots emphasize the discontinuities. Isothermal studies of expansion made upon hydrogen addition gave curves of much smaller slope and less pronounced discontinuities. A uniaxial compressive stress tends to accentuate volume changes in going from the more open bcc phase to the hcp phase.2 Incomplete data on ex-

Jan 1, 1962

By W. Crafts, J. L. Lamont

Electrolytic extraction of carbides from quenched and tempered steel and their examination under the electron microscope were found to be helpful in understanding the mechanism of secondary hardening in alloy steels1 and the same technique has been applied to isothermally transformed steels. A preliminary survey of the utility of the method has indicated that it has promising possibilities for investigating the characteristics of pearlite and bainite. The examination of a few carbon and chromium steels has suggested that pearlite is formed with carbides of two varieties representing the lamellar and nonlamellar forms and that bainite appears to form with a structure analogous to, but significantly different from, martensite. Procedure The method used for examining the carbides was similar to that described previously.1 The chromium steels used in the investigation were made from an Armco iron base in an induction furnace and were not treated with grain-refining deoxidizers. The composition of the steels is given in Table 1. Three-inch square ingots were forged and rolled to 1/8-in. thick sheet for use in the isothermal studies. After rolling, the sheets were sandblasted to remove the rolling scale. Specimens approximately 3/4-in. wide and l1/2-in. long were prepared from the 1/8-in. sheet. They were heated in a salt "bath at 2100°F (1150°C) for 1/2 hour, transferred to other salt baths at 1300°F (704°C), 1000°F (538°C), 800°F (426°C), or 600°F (315°C), held for various periods up to 100 hr and finally quenched in water. After quenching, the specimens were cut in half, one half being submitted to microscopic examination and the other half being used for the electrolytic extraction. The isothermally transformed specimens were submitted to examination under the light microscope to determine the degree of transformation and type of structure and were photographed at 2000 X. Carbide residues were obtained by electrolyzing in 10 pet hydrochloric acid and collecting the residue in glycerine to minimize attack by the acid. As pointed out in the earlier paper, the carbides are attacked to some degree during electrolysis. This attack is relatively minor on the coarser carbides but may be quite severe on the fine bainitic carbides. The residues were washed free of the glycerine with water and alcohol. The alcohol was removed by repeated washings of amyl acetate, and the amyl acetate suspensions were transferred to stoppered vials. Debye-Sherrer X ray diffraction patterns of the residues were prepared using a chromium target. A selection based on the microstructure and X ray data was then made of samples considered most illustrative of the progress of transformation. Electrolytically extracted residues from these samples were submitted to examination by W. D. Forgeng and A. C. Jenkins on the electron microscope at the Research Laboratories of The Linde Air Products Co. and electron micrographs were made at X 5000 and enlarged to 25,000 X. The micrographs obtained with both the light and the electron microscopes are mounted side by side in the accompanying figures. Although no effort was made to establish the T-T-T diagram for the chromium steels, the times for holding in the salt bath were adjusted with the intention of making the samples represent different stages in the transformation at temperatures of 600, 800, 1000, and 1300°F. The degrees of transformation and results of X ray examination are shown in Tables 2—4. The carbide designations refer to orthorhombic or trigonal carbide types and are not meant to imply that the compositions are exactly as indicated. X ray Diffraction Data The occurrence of Fe3C and Cr7C3 in these steels was found to be consistent with published data on comparable chromium steels. Steels A and B with relatively low ratios of carbon to chromium contained Cr7C3 in the pearlitic structures and FeuC in the

Jan 1, 1950

By Denton R. Wieland, Harvey T. Kennedy

The frequency of bubble formation is measured for oils from the East Texas field and the Slaughter field in cores from these fields. East Texas oil was also tested in a Slaughter core. The data checked previous results in that a definite supersatrtration may exist without the formation of bubb1es in periods of observation totaling 158 hours. Measured frequencies varied from zero at supersaturations below 14 psi to 3.1 bubbles/sec/ cu ft of rock at 40 psi supersaturation INTRODUCTION The formation of bubbles is essential in a solution gas-drive reservoir in the displacement of oil. In formations where the basic pore structure consists of fine pores or fractures connected to larger pores or crevices, bubble formation in the fine pores may be the most effective means by which the oil may be displaced, even if secondary methods are applied. The most efficient oil displacement would occur where at least one bubble would form in every pore. As the pressure decreased, the bubbles would expand, due to the gas diffusing into the bubbles, and displace the oil toward the lower pressure area around the wellbore. Kennedy and Olson' have shown that the total number of bubbles formed in a reservoir is primarily dependent upon the rate of pressure drop, the rate of diffusion of gas through oil, and surface area of the rock. The surface tension of the liquid and other characteristics of the rock may also exert an important effect, which would give a different frequency to different rocks and oils and various combinations of different rocks and oils. The purpose of this paper is to present frequency measurements on two rocks and two oils. A hydrocarbon liquid is at equilibrium with gas when it contains the maximum volume of gas in solution that it can have at the prevailing temperature and pressure. If the temperature is maintained constant and the pressure is reduced below the equilibrium pressure, the liquid is supersaturated to the extent of the difference in the two pressures until the gas comes out of solution as a free phase. As shown by previous work, and confirmed in the present investigation, the number of bubbles formed per second increases with an increase in supersaturation. Kennedy and Olson showed that a tenfold increase in the rate of pressure decline resulted in a tenfold increase in the number of bubbles formed per cubic foot of reservoir rock, e.g., for decline rates of 0.1, 1, and 10 psi/day, the number of bubbles formed per cubic foot would be 40, 400, and 4,000, respectively. For another hypothetical system, Stewart, Hunt, and Berry' estimated that for pressure declines of 0.1, 1, and 10 psi/day, the number of bubbles formed would be approximately 10, 100, and 1,000 cu ft of reservoir rock. Their value of bubbles formed is lower than given by Kennedy and Olson; however, the order of magnitude agreed satisfactorily. The rate of diffusion will also affect the number of bubbles formed. If the diffusion coefficient is high, the gas in solution in the oil surrounding a single bubble will tend to diffuse into the bubble rather than forming other bubbles. On the other hand, the formation of more bubbles will tend to occur if the diffusion coefficient is very low. In his thesis dated Aug., 1953, Wood" reports on the frequency of bubble formation in a system consisting of oil and rock from the Rangely field. In the present work, the apparatus of Wood was redesigned to allow greater precision, especially at low supersaturations, where bubble growth is slower, and detection is more difficult.

Jan 1, 1958

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and reGneries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Car1sbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies. Prospecting Since outcrops of potash are nonexistent, prospecting is accomplished by drilling and coring of the salt section to establish the grade, thickness, and outline of the potash beds contained in the salt deposits. Information regarding the nature of the formations in the cover of 400 to 600 ft thick over the salt and potash beds is also obtained from drill cuttings in the same operation. By proper interpretation of assembled data the best location for shafts may be determined. The overburden varies in character but consists in general of interbedded shales, sand, gravels, limestones, and anhydrite beds. Water, in unpleasant quantities, especially in the sands and limestones, often completes the geologic section. Some of the shaftas in the area have been sunk without undue difficulties, others have been delayed by flows of water. Most of the shafts are concreted from the surface to the salt section. Each of the three mines in the Carlsbad area has one shaft for hoisting ore and one for hoisting men and supplies. Mining Methods Information acquired from initial drilling and prospecting affected the choice of mining methods. Since the tabular, slightly rolling deposits were similar to coal seams, the room-and-pillar system used in coal mining was adopted by all the companies. Pillars have not been removed in any of the mines on a large scale. One company has conducted experimental robbing of pillars in one restricted area. Where it is known that overlying strata contain water in large amounts, it is not considered practical to risk flooding of the mines by removing pillars without fill. Some thought is now being directed toward development of economical methods of filling for pillar recovery. The problem is not identical at the three mines and local conditions will govern the methods employed for eventual pillar recovery. The important point is that, with large reserves, it has not been necessary to resort to mining of pillars for adequate production. The ore deposits are laterally extensive but are irregular in shape and lie at a depth of 700 to 1100 ft below the surface. The major operations of all mines are on the same bed strati-graphically, except for the langbeinite level at International Minerals and Chemical Corporation. The deposits are apparently not connected and in many parts of the deposits being mined, "salt horses" or barren zones occur. From 400 to 700 ft of salt with minor beds of polyhalite and anhydrite lie immediately above the ore horizon. The ore differs from the salt only in the potassium chloride content and color due to small amounts of iron associated with the sylvite, giving the ore a somewhat mottled red and white cast. Thickness of the ore varies from 5 to 14 ft. Rooms and break-throughs in the mines vary from 24 to 40 ft in width, the overlying salt forming an excellent roof and providing safe mining conditions. Almost no timber is used in any of the mines for roof support. Drilling is normally the first step in mining the face of a room. Electric motor driven auger drills are used in the area. Jack hammers were used to some extent when the mines were first opened but the ore is easily drilled if bits are sharp and the coal type

Jan 1, 1950

By M. L. Hammond, G. M. Bowers

Silicon dioxide films have been prepared on silicon wafers by the oxidation of SiH, near 400°C. Results previously reported by Goldsmith and Kern7 have been qualitatively corrobovated using a system of different geometry, and significantly greater deposition rates have been achieved. The deposition rate is independent of thickness and nearly independent of the O2/SiH, ratio over a wide range; however, the rate is strongly temperature-dependent. The structure of the deposit depends upon the cleanliness of the substrate, and the electrical field strength of the deposited oxide depends upon the nature of the electrodes. MULTILEVEL interconnects in integrated circuits using aluminum metallization require an insulator that can be deposited at low temperature. Because the A1-Si eutectic is only 577°C, the maximum deposition temperature must be below about 500°C to prevent reaction of the aluminum with the silicon and with other materials in the integrated circuit. Many methods of depositing insulating films of SiO, and other dielectrics have been reported'-6 but the technique described by Goldsmith and Kern7 offers the simplest method of preparing SiO, films. The technique involves the reaction of SiH, and 0, to form SiO, films in the 300" to 500°C temperature range. Previous work using this gas system has been reported8 and the initial development work at Philco Microelectronics was done at the East Coast R&D Laboratories. 9 This paper corroborates some of the results of Goldsmith and Kern,7 shows that much higher deposition rates can be obtained than previously reported, and presents some observations on the structure of deposited SiO, films. EXPERIMENTAL CONDITIONS Fig. 1 is a schematic drawing of the apparatus used in this study. It differs from that of Goldsmith and Kern in that 1) the gases are mixed before they enter the reaction chamber, 2) there is no fritted glass diffuser, and 3) the wafers are stationary during deposition. The control thermocouple was in a well located 0.06-in. from the substrate, and three gas supplies were used: 1 pct SiH4 in N 2, O 2, and N 2. Water vapor must be excluded from the plumbing to prevent the formation of colloidal SiO, and the SiH4 must be diluted with an inert gas because SiH4-0, mixtures are extremely flammable above about 4 pct SiH The wafer temperature was determined by attaching a thermocouple to a test wafer and the temperature was maintained to +5 C. The conditions used in this investigation are listed in Table I. The temperature range was chosen for compatibility with the A1-Si system. The volume ratio of 0, to SiH4 is the actual volume of 0, delivered to that of SiH4, taking into account the initial dilution of the SiH4. This ratio, which was used by Goldsmith and Kern,7 is a useful indicator of the experimental conditions. The active/inactive ratio is the ratio of the volume of active gases, SiH4 and O2, delivered to the volume of dilution gas. The active/inactive ratio is an important parameter to specify for deposition rate determinations since it determines the amounts of reactants that arrive at the sample per unit time. Fairly high dilution ratios were necessary to achieve uniform deposits of SiO,. Most of the process characterizations were performed on the polished (111) face of 3 to 5 ohm-cm, n-type silicon wafers which were 0.009 in. thick; but the data approximately apply to deposition of SiO, on thin films of aluminum. It is difficult to obtain accurate deposition rate data over aluminum films because of coarsening the aluminum surface during exposure to 300" to 400°C. The deposited SiO, film fol-

Jan 1, 1969

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By S. Weinig, E. S. Machlin

IN a previous study of the grain boundary stress relaxation phenomenon,' the authors had arrived at the conclusion that two successive steps were involved in the complete relaxation of stress at a grain boundary. These two steps were grain boundary migration and grain boundary slip. It was further suggested that the slower of these two processes is rate controlling. In an attempt to ascertain the validity of the above, a study of grain growth kinetics on the same alloys used for the previous study was undertaken. Separate wire specimens, 0.030 in. diam, in the same as-deformed state (99 pct reduction in area) as in the previous investigation were heated to the various temperatures for a sequence of times. The compositions used and the temperatures of testing are summarized in Table I. A statistical determination of grain size was then made on each specimen, using the average length of traverse between boundaries as a measure of the grain size. Examples of typical results obtained are shown in Figs. '1 and 2. The grain growth law D = ktn was found to fit most of the data. Using this relation, values of the grain growth exponent n were calculated and the inter -esting dependence of n on solute content shown in Figs. 3 and 4 was then obtained. Also, it was found that the constant K which was obtained from extrapolation is roughly independent of solute content. (K is uncertain to within ±25 pct.) An estimate of the activation energy for grain growth was made using the technique of Burke? This method utilizes the plot of the reciprocal of time necessary for the grain size to increase from a definite starting size Do, to a final size D, for each isothermal heat treatment. The slope of this curve corresponds to the heat of activation for the process. In Fig. 5 the rate of grain growth is plotted against the reciprocal of absolute temperature. The activation energies were obtained from these curves and are summarized in Fig. 6. Discussion It is interesting to note that the same saturation in the variability with concentration has been found for the grain growth exponent n in this research as was found in the previous researches on both grain boundary stress relaxationa and internal friction of dislocation origin." The significant feature is that saturation in the variation of these properties has been found to occur at about the same level of solute concentration, namely, between 0.1 and 0.5 atomic pct. The only characteristic common to these different quantities is that solute adsorption at grain boundaries and dislocation can take place and affect these values in a similar fashion. Thus, it is concluded that the grain growth exponent n depends upon solute adsorption at the grain boundaries. It appears, therefore, that theoretical considerations leading to the contrary conclusions5,6 have not treated the real process by which solute atoms exert their effect on grain growth. Prior to the analysis of the observed activation energies, certain of the aspects of the aforementioned grain boundary stress relaxation investigation will be briefly reviewed. It was found that with the addition of solute atoms the grain boundary stress relaxation peak (internal friction vs temperature) decreased in intensity. Simultaneously a second peak was observed which increased with increasing solute atoms. Both of these peaks were shown to be the result of grain boundary stress relaxation. They have been termed, respectively, poire peak and solute peak. It was suggested that the solute peak was dependent upon grain boundary migration, whereas the pure peak was a manifestation of grain boundry slip. Activation energies for both peaks were obtained as a function of Solute content. The value of the activation energy in the temperature range corresponding to the solute peak was

Jan 1, 1958

By G. R. Smithson, John E. Hanway

This paper, the first of two papers covering the development of a metallurgical process for the treatment of a complex ore, describes the bench-scale experimental Program undertaken as a basis for initial process design. The results of using various potentially applicable process steps are detailed and the basis for selecting certain of these steps for Pilot-plant development is outlined. A process consisting of the steps of sulfate roasting, leaching, copper recovery, solution purification, zinc electrolysis, and brine leaching for lead recovery was recommended for further study. THIS paper describes the bench-scale development of a sulfate roasting process designed to recover copper, lead, and zinc from a complex ore. The extrapolation of the bench-scale results to pilot-plant design and the results of pilot-plant operation will be described by Lund, et al.' in a subsequent paper. Several years ago, the research divisions of the St. Joseph Lead Co. became responsible for the development of a metallurgical procedure to treat a complex sulfide ore containing copper, zinc, and lead sulfides. The primary objective was to devise a procedure which would permit economic recovery of the nonferrous values. As could logically be expected, the study of conventional flotation procedures was undertaken; in addition, however, because the physical nature of the mineral association in the complex ore indicated that physical methods of ore beneficiation might not prove to be entirely satisfactory, a program also was established to investigate alternative methods of direct metallurgical treatment for recovery of the metal values. Exploratory test work by the St. Joseph Lead staff led to the conclusion that a sulfate roasting technique represented the most attractive approach for a direct metallurgical process. Sulfate roasting would provide for the selective conversion of the nonferrous values to forms soluble in conventiona1.1 leaching agents and would permit their efficient separation from the insoluble iron and other gangue materials. It should allow efficient utilization of the thermal energy available from oxidation of the sulfide raw material, and might provide an opportunity for recovering byproducts such as iron and sulfur. The decision to evaluate a selective sulfation procedure as a basic processing step also was influenced by the excellent results obtained by the St. Joseph Lead Co. in using this procedure for the recovery of cadmium from zinc sulfide concentrates. The choice of selective sulfation as a major processing step served as a basis for an extended experimental investigation of the process with bench- and pilot-scale equipment to prove its feasibility. St Joseph Lead Co., aware that Battelle Memorial 1nstitute had participated in the development of several fluidized-bed sulfate roasting procedures, asked Battelle to undertake the bench-scale development of a suitable sulfation process. This paper describes the procedure used and the results obtained at Battelle in the treatment of the complex sulfide ore. EXPERIMENTAL WORK Nature of the Raw Material. The sulfide ore deposits of interest are essentially a massive sulfide, with the indivudual ore minerals being extremely fine grained and intimately intergrown with each other and with the associated gangue. The zinc in the ore is present mainly as sphalerite (ZnS), the lead as galena (PbS), and the iron either as pyrite (Fes2) or as pyrrhotite (FeS). Table I shows the chemical analysis of various individual samples of the ore. These analyses illustrate the variability of the ore body and impose a rather severe requirement on any type of metallurgical process—that of being able to tolerate probable wide variations in the assay of the head ore. The tentative flowsheet designed to serve as a guide for the initial experimental investigation of

Jan 1, 1962

By M. Cross

INTRODUCTION The development of refining processes involving gas injection into liquid metals has seen the evolution of a variety of designs [I]. During the last few years or so the top, bottom and side blown processes have, essentially, been combined to produce a series of mixed gas blowing schemes (eg. the LBE [2,3] and LD-OB processes [4,5]). Although, a variety of mixed gas blowing processes have been carefully engineered and recorded operational experience now attests to their effectiveness, optimising their design and operational performance is another matter. Detailed process analysis of such operations is impeded by the complex nature of the physical and chemical processes involved: . fluid flow behaviour of the liquid metal and injected gases, . chemical reactions in the vessel, . mass and heat transfer within the fluid phases in the vessel, . influence of the geometry (eg. location of the tuyeres, etc.), . monitoring the operational performance. By and large, design and operating parameters evolve from a combination of laboratory scale experiments, pilot plant work and, of course, practical engineering experience. Conventionally, the gas-liquid system used to model the industrial process is air-water, for a number of valid reasons including – . visual demonstration plus geometric and (to some extent) dynamic similarity, . the fact that the system demonstrates, at least, qualitatively many of the complex features of gas injection - interaction between the gas and the liquid - the nature of the gas flow behaviour - qualitative indications of mass transfer rates Important experimental contributions to the understanding of gas liquid systems include the work of Brimacombe [6], Wraith [7], T.Robertson [8], D.Robertson [9], Guthrie [10] and Szekely [11] (these references provide starting points to identify the major published work in this area). Although air-water systems have been instrumental in providing a great deal of qualitative insight into the fluid flow behaviour of the processes, reliable quantitative predictions are more problematic. A number of workers (notably Brimacombe and colleagues [6, 12])have demonstrated that different gas-liquid systems can lead to wide variations in behaviour. Other limitations of physical modelling include the assumptions of isothermal flow, scale- up of turbulent flow behaviour and the inability to directly include the effects of chemical reactions. The above limitations in physical modelling, therefore, yield a natural role for mathematical modelling provided that it can be made comprehensive enough whilst remaining cost-effective. The major physical processes involved in gas injection systems may be summarised as . behaviour of the gas envelope structure in moving through the liquid metal . the global movement of the liquid metal . momentum interaction between the liquid metal and the injected gas . heat transfer and mass exchange via the chemical react ions. The behaviour of gas envelopes forming at a tuyere and then moving through the liquid has been investigated thoroughly by a large number of workers. Such models are generally based upon simple physic- al concepts derived from visual observation. An early model by Davidson and Schuler (DS), based upon a force balance between the liquid inertia and a combination of the bouyancy and momentum forces on the envelope, has proved to be a useful tool in predicting bubble volumes at detachment [13]. The DS model has been successfully modified in a number of ways [14-17] to cope with heat transfer and reactive transfer rates, etc. Furthermore, the basic ideas summarised above have also been confirmed on industrial converters by both Guthrie [I8] and Brimacombe [19]. Models have also been developed to predict the behaviour of the "chemical" component of some gas-liquid systems. However, one thing is clear; all gas-liquid reactive systems are governed by the degree to which effective mixing occurs. As such, the processes are dominated by the behaviour of the heat and mass exchange of the two phase fluid flow system. It is the pattern of movement of the turbulent liquid metal plus its interaction with the injected gas which must be predicted reliably, if sufficiently comprehensive comp-

Jan 1, 1984