Search Documents

By D. G. Westlake, D. T. Peterson

The saturation solubility of thorium dihydride in thorium was studied by saturation of samples and subsequent analysis. The solubility increased from about 1 at. pct at 300°C to above 20 at. pct at 800 °C. Over this temperature range the log of the solubility was a linear function of the reciprocal absolute temperature for thorium of good purity. The heat of solution of thorium dihydride was found to be 7.9 kcal per atom of hydrogen in crystal bar thorium and 6.6 kcal per atom of hydrogen in Ames thorium, The important effect of hydrogen on the physical and mechanical properties of many metals is receiving increasing recognition. The basic physical and chemical data necessary to help explain the observed effects of hydrogen on the mechanical proper ties of metals are all too often not available. The solubility of hydrogen in thorium metal was determined to provide a portion of this basic data for the thorium-hydrogen system. The absorption of hydrogen by thorium metal and the formation of thorium hydrides was studied by several investigators, beginning in 1891, and their work is summarized in Gmelin's Handbuch.1 No effort was made to determine the extent of solid solubility in the metal in these early investigations and the impure metal available made interpretation of the results uncertain. Nottorf2 reported the results of a careful study of pressure-composition isotherms for the thorium-hydrogen system. The principal interest in this work was in the composition and dissociation pressures of the thorium hydrides. Mallett and campbel13 reported the pressure-composition isotherms for the thorium-hydrogen system up to the composition of thorium dihydride. The saturation solubility of thorium dihydride in thorium was reported to be 13 at. pct at 650°C and 23 at. pct at about 900° C. Mallett and Campbell used thorium metal which had been prepared by the calcium reduction of thorium tetra-fluoride or thorium oxide. The results obtained with thorium of these two types agreed within the experimental error. PROCEDURE AND MATERIALS Procedure—The method used to determine the solubility was to saturate a sample of thorium with hydrogen and analyze a portion of the saturated sample. This method was chosen rather than a determination of pressure-composition isotherms since it was much less time consuming and could be applied at temperatures at which the equilibrium hydrogen pressure was too low to measure. The

Jan 1, 1960

'T. C. MERRIMAN, New Haven, Conn. (written discussion *).-This most interesting paper gives much carefully obtained and valuable data. However, there are two points in connection with the commercial application of such data that might possibly be a source of trouble and mis-understanding. In the first place, the examination of thin sections of annealed brass, subjected to standard Brinell test.(500 kg. on a 10-mm. diameter ball) at thicknesses from 0.075 to 0.150 in. (1.9 to 3.8 mm.) indicates that cold work has been performed on the specimen during the application of the load sufficient to extend way through the section, and have the hardness of the metal affected by the backing. If the usual steel support is used, this effect is very evident. If a piece of soft brass is used as a support, there is an indentation in the surface of the support accompanied by a bulge on the under side of the tested specimen opposite the impression made by the 10-mm. ball. The result is that Brinell specifications (governmental or otherwise) on stock for a certain purpose may not be fair in all cases, since manufacturers, owing to differences in equipment, etc., may not all use precisely the thickness and conditions of stock on which the Brinell specifications were based. This would mean that the government Brinell specification might not give them the temper of stock best suited for their manufacturing methods. The concluding paragraph of this paper, stating that "the hardness of cartridge brass may be determined with greater accuracy by the Brinell hardness measurement than by attempting to judge it from the grain size" appears to be in line with the movement of the last year or so among brass manufacturers toward substitution of the Brinell test for microscopic examination as an acceptance test on cartridge brass. The statement may he strictly true that the Brinell test is the best test for hardness, but it is not, as the statement might readily be construed, a sufficient test of suitable condition. For instance, some cartridge brass might accidentally have been overheated to a point where it would be distinctly unsafe to use for the manufacture of small arms cases and then be so rolled (reduction 3 to 5 per cent.) as to pass perfectly proper Brinell specifications. Under such conditions the microscope would reveal its unsuitability where the Brinell test had failed so to do.

Jan 4, 1919

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By C. Wert, G. Mah

A relaxation peak thought to be due to the presence of C-C pairs in cobalt has been observed. It exists both above 420"C, where cobalt has the fcc structure, and below 420"C, where cobalt has the hcp structure at equilibrium. The effect is thought, however, to be caused by motion of C-C pairs in the fcc phase in both instances; enough retained fcc phase was deduced to be present at temperatures below 420°C to make the phenomenon possible. Measurements of the aniso-tropy of the effect in single crystals of various orientations of fcc phase showed the effect to have a maximum value in longitudinal strain for a [loo] crystal and a minimum value for a [Ill] crystal. This observation seems to rule out the possibility of (110) nn pairs being responsible for the effect. From measurements of the strength of the relaxation in the alloys, we reach the conclusion that both the binding energy of the pairs and the specific relaxation per pair are smaller than corresponding quantities for interstitial pairs in bcc metals. DETERMINATION of the details of atom placement of small atoms such as carbon, nitrogen, oxygen, and hydrogen in metals has been a difficult problem. In certain alloys such as martensite extensive departure from random placement of the interstitials can be deduced from X-ray diffraction off the atoms of the host metal, but such diffraction techniques are of small help for small departures from randomness. A technique which does offer promise in the latter instance is the anelasticity of these interstitial alloys. Most previous investigations using this property have utilized alloys in which the solvent is one of the bcc metals, alloys such as These studies have been interpreted to show that an interaction exists between interstitials which causes them to form clusters in more than random numbers; the binding energy of interstitials in such clusters has been deduced to be about 0.1 ev per atom (for small clusters of size two to four atoms). Similar investigations have been carried out on close-packed solvent metals, Ni-C by and Diamond and Ag-O by Papazian.8- In both of these svstems. no relaxation of the singly dissolved interstitial is expected, so an-elastic behavior of the interstitials must be caused by their association in some cluster or complex of non-cubic symmetry. Since relaxations in these alloys were observed to have a strength which varied about as the square of the interstitial concentration, the effect was deduced to be caused predominately by motion of i-i pairs in the crystal. A striking difference is observed in relaxation strength of interstitial alloys between the bcc and fcc systems. The specific effect per interstitial atom is much larger for the alloys in the bcc crystals than for those in fcc crystals. Comparing clusters of size two in the Nb-O system4 and the Ni-C system,7 one finds the magnitude of the anelastic effect per interstitial atom in the former to be some 100 times greater than that in the latter. Such a difference in relaxation strength might be caused by a difference in concentration of the pairs (this means a higher binding energy in the bcc crystals). It might also be caused by a large difference in shape factor of the elastic strain field about the pairs between the two cases (a much more noncubic shape factor would be required for the bcc crystals). This investigation was undertaken to examine the possibility of C-C pair formation in alloys of cobalt and carbon using anelastic effects. Since cobalt has both fcc and hep phases, it seemed to offer the chance that measurements over a range of frequency might permit comparison of properties of pairs in the two crystal types. Although this goal was not reached, several significant facts were deduced from the observations. 1) An anelastic phenomenon believed to be associated with the presence of C-C pairs in cobalt exists. It has many features in common with that observed in nickel. 2) The effect is thought to be caused by pair motion in the fcc phase. 3) Calculations of the relaxation strength A, which includes as a parameter the product of the pair concentration, C, and the square of the shape factor ', show that this parameter is much smaller in the CO-C alloy system than in the interstitial alloys in the bcc systems. 4) From this finding, we reach the conclusion that both the binding energy of C-C pairs in cobalt and the specific relaxation strength per pair are small compared to corresponding values for such pairs in the bcc systems. 5) The crystalline anisotropy of the effect permits the identification of reasonable geometrical models of close C-C pairs. I) EXPERIMENTAL PROCEDURE A) Method of Measurement. The anelastic measurements-—all of which were constant frequency measurements of internal friction—were designed to study the expected phenomenon in both the hcp and fcc structures in cobalt. Knowledge of similar measurements in Ni-C alloys led us to believe that the damping peak should occur below the transformation temperature for frequencies near 1 cps and above for frequencies near 100 kcps. This surmise was correct. The low-frequency measurements were made on wire specimens using a vacuum torsion pendulum; the damping peak was found at about 2'70°C at a frequency of 1 cps. Because of large superimposed damping of magnetic origin at this temperature, a longitudinal magnetic field of about 1500 oe was applied to the

Jan 1, 1969

By L. C. Brown, C. St. John, C. C. Sanderson

The diffusion rate in Cu-Te couples is very sensitive to compressive stress, with a load of 20 psi making a significant difference to the width of the diffusion zone. At zero stress, two phases appear in the diffusion zone (Cu4Te3 and CuTe). Under compressive loading the third stable phase (Cuz Te) also appears, and its thickness increases progressively with increasing stress. The results are explained on the basis of an incipient Kirkendall porosity which restricts the transfer of atoms from the copper into the diffusion zone. DURING a study of the Kirkendall effect in Cu-Te couples prepared by clamping together the two components, it was found that the diffusion-zone width and shape in the plane of contact were not reproducible. Although the stresses involved in clamping are not normally sufficiently high to affect diffusion rates, preliminary tests established that the Cu-Te system is particularly stress-sensitive. The phase diagram for the system Cu-Te given in Hanssen1 shows that there is practically no solid solubility at either end of the phase diagram. Many areas of the diagram are not fully substantiated, but there appear to be three intermediate phases: Cu,Te—hexagonal in structure, having a grey luster; Cu4Te3—a tetragonal defect structure, having a red-purple luster; CuTe—orthorhombic in structure and having a golden-green luster. The existence of a fourth phase, the X phase at 37 at. pct Te, is considered doubtful. The composition ranges of the three stable phases are small, and are not accurately known. The phase diagram changes little with temperature up to 305°C, at which temperature a polymorphic transformation takes place in Cu2Te. The nature of the Cu-Te phase diagram indicates that the diffusion zone in a Cu-Te couple would consist of a series of layers of intermediate phases. The relative thickness of any one phase will depend on its diffusion coefficient and composition range.' In this type of diffusion couple it is often found experimentally that some phases are not visible at all in the diffusion zone due either to a small diffusion coefficient or to a restricted composition range.3 Since the composition ranges of the phases in Cu-Te are not known, it is not possible to determine diffusion coefficients in this system from a knowledge of the phase thicknesses. Several investigations have been carried out to determine the effect of compressive stress on diffusion rates in multiphase systems. Diffusion couples of Ni-A1 have been investigated by Storchheim et al.4 and by Castleman and Seigle.5 Two phases (ß and ?) appear in the diffusion zone under zero stress and the thickness of both phases is progressively reduced with increasing stress. According to Storchheim et al.4 a stress of 25,000 psi reduces the thickness of the diffusion zone by 50 pct. In a-brass—?-brass couples the thickness of the 0 phase formed in the diffusion zone was reduced by 20 pct at a stress of 20,000 psi.6 In other investigations the compressive load has been observed to increase the width of the diffusion zone. In A1-U, several investigators3,8 have found the width of the whase UA13 to increase with stress. According to casileman,8 the rate of formation of UA13 at 520°C is 75 pct faster at a stress of 20,000 psi as compared with a stress of 2500 psi. In Cu-Sb the effect of stress is greater than in the other systems described. According to Heumann9,10 only one phase (y) appears in the diffusion zone at a stress of 500 psi, but at a stress of 850 psi two phases (y and k) are present. If a diffusion couple containing both y and k phases is annealed at a low stress level, the y phase grows at the expense of the k phase. EXPERIMENTAL The diffusion couples were prepared from electrolytic copper bar stock with a nominal purity of 99.92 pct and from tellurium of 99.7 pct purity. The tellurium proved difficult to machine because of its brittleness and a technique was developed for casting the tellurium into a graphite slab mold and spark-machining specimens from this slab. Both the copper and tellurium were produced in the form of discs 2 in. diam by approximately 1/4 in. thick with surfaces ground flat to 3/0 emery paper. The diffusion apparatus is shown in Fig. 1. Auni-axial compressive stress was applied to the system through a simple lever system. A stainless-steel rod actuated by the lever arm lay inside a stainless-steel tube. The diffusion couple lay on top of the steel rod, and pressure was applied to the couple between the rod and a plug welded into the center of the tube. To ensure a uniform stress across the couple, a hemispherical boss and cup were used to transmit the load to the diffusion couple. A 400-w tube furnace with a uniform hot zone 3 in. long slid around the stainless-steel tube and maintained the assembly at temperature. A thermocouple situated 3 in. from the specimen operated a proportional temperature controller which maintained the specimen temperature constant to ±2°C. Most diffusion runs were carried out at 250C although a few tests were made at other temperatures in the range 235° to 300°C. The specimens were inserted and removed with the furnace at operating temperature, and took only 2 min to reach diffusion temperature—a time small compared with the total diffusion time. All the diffusion experiments were carried out in a hydrogen atmosphere, since consistent results were obtained in hydrogen and nitrogen atmospheres and in

Jan 1, 1967

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By Charles T. Malcomson

In the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segrega,ted and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promoters heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay. Several valuable contributions relating to coal briquetting are found in the Transactions. Charles Dorrance, Jr., has sketched briefly the history of the anthracite briquetting plants from the time of Loiseau's pioneer plant down to that of the Lehigh Coal & Navigation Co. at Lans-ford. Since then this phase of the industry has remained practically at

Jan 1, 1915

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.' Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph' (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,' have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

The plans for the activities of the Petroleum Division for the coming year do not differ materially from those of the past several years. The fall meeting is scheduled for Oct. 12 and 13 and is to be held at Tulsa, Oklahoma. The Division, of course, will take part in the annual meeting of the Institute at New York. A fall meeting will also be held in California at approximately the same time as the meeting at Tulsa. A number of papers are to be presented at the two meetings simultaneously. The various committees are at work arranging the programs. The Division will continue to be active in its various fields of endeavor, such as stabilization, production reviews, and economics, but special stress is to be laid on the engineering and research fields. In the past the Division has served as a forum for open and frank discussion of problems confronting the engineers in the oil industry. It is hoped that it will continue to function in this capacity. Papers presenting original ideas and extending the boundaries of knowledge and understanding in the field of petroleum production will be welcomed. Members who have interesting information to contribute should not wait until called upon by one of the Committees, but should offer a paper at the earliest opportunity. The past year has seen a decided strengthening of the control over production, with prospects of even more rigid control in the future. It is essential that production programs under such control be carefully planned and it is highly desirable that petroleum engineers take an active part in the planning, to insure efficient production of oil and minimize the waste of this natural resource. At a time like this, when it is difficult to keep the production of oil within reasonable limits, it may seem unnecessary to improve the efficiency of production methods, but, as has been aptly said, the trouble is not that we have too great a reserve of oil but that we are producing tomorrow's oil today. Therefore it behooves those who are entrusted with the engineering and scientific phases of production to learn how to get the greatest yield economically possible from the present and future fields in order that we may enjoy the advantages of petroleum products for a long time to come.

Jan 1, 1934

By O. U. Bradley

THE extent of losses, due to evaporation, sediment, and water, in crude oil stored in steel tanks, is a very interesting question, and particularly so at this time, when every reasonable measure should be employed to eliminate all possible losses of this important natural product. Available information on this subject is incomplete; e.g., during the development of the Cushing Field, considerable surplus oil was stored in steel tanks, but from time to time, owing to changes in weather, somelosses by evaporation and short storage room on the leases, these tanks were topped out, thus rendering inaccurate any system designed to determine the average rate of evaporation or other losses of the oil over a given period. , Furthermore, the losses, as shown by the records at the time, as a result of hasty gages, failed to take into account the temperature and gravity of the oil. Losses may be classified roughly as occurring from evaporation, presence of sediment and water, and leakage. The coefficient of expansion and contraction of crude oil, in relation to temperature conditions, is of material importance; also, the rate of evaporation is dependent upon the gravity of the oil, as the escape of the lighter hydrocarbons in fresh Cushing oil, of from 40 to 42 gravity, on a warm day is considerable, and from available records of temporary storage, it is safe to assume that a loss of 1 to 13 per cent. in volume will easily occur in light crude oil of Cushing grade over a period of. 6 months, including the summer season. The presence of sediment, water, and other impurities, in the oil will also cause, more or less deterioration in quality, particularly when the fresh production is run direct from the. gage tanks, or from the wells on the lease to steel storage, as is often the case when an oil field is being rapidly developed. The bad oil will settle to the bottom of the tanks and may be determined by thiefing and running a centrifuge test on the sample. The amount of water in the oil depends entirely on the conditions under which it is produced. Sometimes in large producing wells, with heavy gas pressure, some water may come in with the oil, particularly if the well has been drilled to the top of a water sand. Under these conditions, cut oil is often produced, which, if not settled out, is carried over into the steel tanks.

Jan 7, 1918

PUBLIC hearings began before the Committee for Reciprocity Information on May 24, 1950, for the purpose of unearthing data and opinion that will be helpful in the forthcoming reciprocal tariff and other trade-barrier negotiations at Torquay, England, on September 28th of this year. The conference this fall will constitute the "third round" of tariff negotiations under the General Agreement on Tariffs and Trade concluded at Geneva in 1947. The United States plans to negotiate with 17 other countries on possible tariff modifications on various articles all the way from baby carriages and bottle caps to lead and zinc-bearing ores. On May 31, June 1 and June 2, spokesmen appeared before the Committee for Reciprocity Information on behalf of the domestic lead and zinc mining industries. Producers of these metals protested the inclusion of paragraphs 391 (lead-bearing ores, dust and mattes), 392 (lead bullion, lead in pigs and bars, and scrap lead), 393 (zinc-bearing ores of all kinds), and 394 (zinc in blocks, pigs or slabs, and zinc dust) of the Tariff Act of 1930, as amended in the list of articles to be considered for possible tariff concessions at Torquay. It was pointed out that although operating costs have more than doubled since 1939 tariffs on these metals were actually higher in that year than at present. This, coupled with the detrimental effects of the recent series of devaluations, has sounded the death knell for a substantial number of domestic lead and zinc mines-a most undesirable development in the face of the ominous international situation, according to these spokesmen. It was urged that higher rather than lower tariff rates are needed on these metals. The opinion was expressed that it was inconsistent to foster a high living standard in our western areas and then, once it is attained, to undermine that condition by minimizing the protection that was partly responsible for it. The main theme of some arguments implied that although every effort should be made to close the "dollar gap" abroad, serious consideration must be given the methods employed lest our national security position be jeopardized in the process. The House Committee on Foreign Affairs completed hearings on H. J. Res. 236, to provide for United States membership and participation in the International Trade Organization. Hearings began on April 19th and ran for over five weeks. Many witnesses from industry and government presented voluminous testimony, which will not be available for public distribution for several weeks. However, it is no secret that the most controversial provisions of the Draft Charter of the ITO are: (1) Article 17 (Chapter IV on Commercial Policy) which would obligate members to negotiate for the reduction of tariffs and the elimination of trade preferences; (2) Article 20 which would prohibit the use of quantitative restrictions for protective purposes; (3) Article 16 which promulgates rules to implement the principle of non-discrimination in international trade; and (4) provisions permitting the use of protective measures for promoting economic development, particularly in backward areas, even though such provisions are inconsistent with those of the three articles cited above. United States membership in the International Trade Organization is essential to the successful operation of that body in view of this country's position as the economic giant in the present international trade pattern. Many countries are reluctant to take any action toward the ratification of the charter until it is known what course America will pursue. However desirable or undesirable the ideal of free multilateral trade may be it is unlikely that this Government's participation in the ITO will materialize soon. Advices in Washington indicate that H. J. Res. 236 will not be enacted during the present session of Congress. The legislative pattern designed to secure Congressional approval of the ITO is similar to that of the St. Lawrence Seaway project. The Seaway project was pending in treaty form for several years before the Foreign Relations Committee of the Senate and when the Administration decided to incorporate this project into bill form it was found that, while it passed the House promptly, the Senate decided to pigeonhole it because of the obvious intent to circumvent the constitutional prerogative of the Senate to advise and consent to the ratification of treaties. The ITO bill may be slated for a similar fate. It is deemed essential by western Senators and Congressmen that the present session of Congress enact some form of mining legislation before its adjournment, now set for July 31st. These legislators from prominent ore-producing states do not desire to return to their home areas in the fall emptyhanded. Aside from that, it is entirely superfluous to reiterate the necessity for maintaining a healthy domestic mining industry as a bulwark against a sharp rise in the temperature of the "cold war". Now that S. 2105 has failed a new bill is taking shape in the Senate Interior and Insular Affairs Committee. It is similar in language to H. R. 8221 (to encourage the conservation and development of the mineral resources of the United States) reported by the House Public Lands Committee on May 3, 1950, but so far has failed to receive approval of the House Committee on Rules. There are some qualified observers in high circles in Washington as well as in the mining industry who favor a tax incentive program to stimulate investment in mining enterprises, as opposed to a conservation and exploration program. The Bureau of Mines and the Treasury Department have undertaken a joint study to determine the need for modification of the tax laws as they apply to mining. The study is scheduled for completion before the end of the year, and appears to be supplementary to the investigation initiated by the National Minerals Advisory Council which culminated in the submittal of recommendations to the Secretary of the Interior in December 1949. The "cold war" is largely responsible for the increased demand for metals. Stock-pile purchases and heavy industrial demand due to military needs distort markets and disrupt normal price trends. Such activity has an unhealthy influence on metal production, luring some producers into a state of dependency on the continuation of this condition. When stock-pile objectives are met sometime in the future purchases must then come to a halt unless international "fireworks" are touched off. It can only be hoped that technological improvements and further mechanization of mines coupled with the stimulus of a rising population will offset the anticipated drop in industrial demand and cessation of stockpile purchases when the international crisis abates.

Jan 7, 1950

By John M. Hartman

(Read at the Wilkes-Barre Meeting, May, 1877.) Two systems are used for heating air in blast-furnace operations I. The double surface system, in which a cast-iron pipe is heated on the outer surface, and, at the same time, heats the blast from its inner surface. This is simple in operation and gives a continuous effect, but is limited by 1100° F. as a maximum temperature of the blast. II. The single surface system, by which large surfaces of fire-brick are heated, and air passed over the heated surface, absorbing the heat and carrying it on to the furnace. This system is more complex than the double surface, as it involves the reversing of the air and gas every hour and a half. The single surface system has two advantages: 1. The blast can be heated to a temperature of 1800° F. 2. The stoves are indestructible. From recent experience it has been found that 1300° F. to 1400° F. is the best average temperature for economy of coal for safe work¬ing. This is equivalent to a saving of 12 to 2 cwt. of coal per ton, of iron over the extreme limit of cast-iron stoves. Independently of this, it is a strong point in favor of this system that the blast can be raised to a temperature of 1800° F. within an hour when the hearth is getting cold. All furnacemen know the value of a hot hearth for quality and quantity of iron. Cooling of a hearth occurs from leaky tuyeres, scaffolds, or heavy burden. When there is not sufficient coal at the tuyeres to seize on the oxy¬gen of the entering air and convert it at once to carbonic oxide, there will not be enough heat to liquefy the cinder. Black cinder and poor iron are the results. The remedy is additional heat from the blast. If the stoves will give 1800° in place of 1100°, it is obvious that the furnaces will get around sooner, and without waiting for a change of burden at the tunnel head to bring extra coal to the hearth. The heat absorption caused by a leaky tuyere will chill the hearth and drive the zone of fusion higher up in the furnace. This loss must be supplied, and the calories lost to the hearth must be regained before good iron can be made. Take another case : A furnace carefully burdened on No. 1 iron, during a spell of damp weather, goes on to No. 2 or No. 3. Heat is lost to the furnace through absorption by the moisture, and less burden must be carried in order to get back on No. 1. When the

Jan 1, 1878

By W. G. Pfann

THE problem of forming points on wires that were from 0.002 in. to 0.010 in. in diam arose in the recent appearance of silicon and germanium point contact rectifiers as elements in microwave radar.1 In these devices a pointed tungsten wire makes a delicate contact with the surface of a semiconductor. Because the quality of such rectifiers is largely determined by the nature of this contact, considerable attention has been given to the formation of the metal point. Reproducibility of contour and freedom from burrs and even microscopic irregularities are considered essential. The operations involved must be simple and rapid enough for mass production. Previously tungsten wires had been provided with conical points by a grinding method which involved rotating a wire about its axis and causing it to bear at an oblique angle against a spinning abrasive disc. This was later complemented with an electrolytic polishing treatment which removed irregularities from the ground point and also rounded it off at the tip-a desirable feature. Finally, these operations were supplanted by the electrolytic pointing method described here. MECHANISM OF POINT FORMATION The wires to be pointed are partially immersed- in an electrolyte in a .vertical position whereupon they are provided with smooth rounded points entirely by electrochemical action. The process is independent of the depths to which the wires penetrate the electrolyte because the points are formed at the surface level. It may be used to point a single wire or many of them simultaneously and is applicable to wires of different diameters within a limited range. Solution of the immersed portion of a tungsten wire is accomplished by making it the positive electrode in an electrolytic cell, as shown in Fig I. While the wire is maintained at constant voltage the current through the cell falls continuously, principally because of the decrease in wetted area which results from solution of the tungsten. This increase in resistance occurs in a reproducible manner and is used as a control in the process. As the immersed portion of the wire dissolves, it remains cylindrical in shape except for the short section which is wetted by the meniscus. Here the rate of solution is lower and decreases as the top of the meniscus is approached. The result is the formation of a tapered section inside the meniscus. As solution continues, the cylindrical section either dissolves entirely or drops off just before complete solution, leaving only the taper which is now sharply pointed. Further action causes this point to become rounded and then quite blunt, until finally the end of the wire is almost plane. Fig 2 shows the stages in this development. Contour PF is most representative of those used in point contact rectifiers. Thus a variety of point

Jan 1, 1947

By Fred C. Bond

THE process of comminution by grinding is properly classified as an art, rather than as a science. Like most other operations concerned in ore dressing, or in the treatment of nonmetallic minerals, the mathematical relationships of rock breaking are still obscure, and much disputed. If some basic formula exists, comparable for instance to E = RI in electricity, it has not yet been placed in, common use. The absence of such a comprehensive mathematical background undoubtedly is the cause of many inefficient designs and installations, as well as of much poorly oriented experimental work. On the other hand, the mathematical immaturity of the process constitutes an opportunity for a real contribution on the part of those who enjoy mental pioneering. Some of the statements made in any such exploratory work may be little more than opinions, and it is to be expected that some will later be proved untrue; but such an evolutionary development is necessary if we are ever to arrive at the fundamental laws, the discovery of which can change the empirical art into a mathematically exact science. The most significant principle of comminution that we possess is probably Rittinger's law, which states that the work done in crushing or grinding is proportional to the area of the new surface produced. There is an alternative theory, known as Kick's law, which formerly was preferred to Rittinger's but which now is rather discredited. According to Kick, the work done in comminution is proportional to the volume, or weight, of the pieces broken, or to the cube of their diameters, while according to Rittinger it is proportional to the square of the diameters. Careful determinations of size distribution below the limit of sieve sizes1 indicate strongly that under ordinary grinding conditions the amount of new surface area produced is directly proportional to the net power input. Changes in the size ratio between the balls and the particles cause important differences in the proportion of the product that passes a given mesh size, but do not affect the total amount of new surface area; they merely change the distribution of the surface among mesh sizes. The principle of constant surface area is the logical result of Rittinger's law, and it may well have an important bearing on the comminution theories of the future. FORMULA FOR BALL WEAR Grinding tests have been made in the Allis-Chalmers laboratory for more than 9 years, using a standard charge of mixed balls of different sizes; and a continuous record has been kept of the rates of wear of each size. These results have been combined and plotted in various ways in order to discover the relationship that exists

Jan 1, 1940

By John H. Melvin

THE Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. GEOLOGY Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its uncemented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable - slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1947

By John H. Melvin

The Omaha District, Corps of Engineers, has been doing subsurface exploration work for a number of years, both by contract and with its own forces. Certain practices and procedures concerning the recovery of large diameter cores have been developed which will be described in this paper. Geology Most of the drilling to date has been in connection with structures on the main stem of the Missouri River above Sioux City, Iowa. A wide variety of subsurface conditions has been encountered. The bedrock formations appear in regular order from the oldest to the youngest, traveling upstream; or in other words, the general regional dip is to the northwest. The oldest formation is the Carlile shale, a compaction or noncemented waxy shale of Cretaceous age. Because of its unce-mented, soft nature this shale has a tendency to grind or wash away when drilled. It also has a tendency to rebound or expand when the overlying pressures are removed. A 25-ft bed of sharp, friable sandstone called the Codell member is present near the top of the Carlile shale. This member is a cemented sediment, but in drilling, many of the sand grains are broken loose and exert extensive abrasive action on the core barrel and bit. Above the Carlile shale is the Niobrara chalk, a soft calcareous deposit with shaly horizons and some thin beds of bentonitic clay. The average thickness of this deposit is about 145 ft. It is soft enough to be sawed or bored with ordinary woodworking tools, yet is compact enough to be used as building block. The Pierre shale, the formation above the Niobrara chalk, is over 800 ft in thickness and is the most widespread material in the area. It is a dark colored, compaction shale containing numerous thin bentonitic clay seams and at certain horizons, hard manganese concretions. The shale has numerous faults and in addition, along the valley walls, has undergone considerable slumping. Joints, fault planes and slickensided surfaces are common features encountered in drilling and add to the difficulties of high core recovery. East of the Missouri River the bedrock is generally covered with from 100 to 200 ft of glacial till, composed of clays, silts, sands, gravels and boulders. The valley itself is filled with alluvial deposits, mostly of the sand and gravel sizes, and contains a buried preglacial or interglacial channel over 100 ft in depth. The overburden deposits require sampling in connection with engineering studies and must also be cased before the underlying bedrock can be cored. The diameter of the required overburden samples can thus have an indirect effect on the size of core recovered from the bedrock. West of the river, which in most cases is the western boundary of glaciation,

Jan 1, 1949

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943