Search Documents

By R. W. D. Clarke, J. C. Folinsbee

INTRODUCTION This paper deals with a procedure for planning the mining of an orebody for which cross-sections, plans, grade of ore, and a geological estimate of the ore reserve have been prepared. The procedure begins with the preliminary selection of a mining method or methods on which an engineering evaluation will be carried out. The engineering evaluation is described in three parts: Conceptual Studies Engineering Studies Detailed Design An overall planning model is presented, plus an expanded model for the Engineering Study Throughout the discussion of the planning procedure, reference is made to three bulk mining methods, including block caving, sublevel caving, and longhole sublevel stoping, including a summary of the main characteristics of each of these mining methods. The planning model is designed for a longhole sublevel stoping method, but with modification, will apply to other methods. PRELIMINARY SELECTION OF A MINING METHOD To experienced mining engineers, identification of the nominal mining method for a given orebody normally involves a large measure of judgement. The geological data is reviewed to determine the configuration of the orebody, including size, shape, dip, grade, and metal distribution. Geotechnical data is considered, including the competence of the ore and host rock, faults, fracture patterns, groundwater, and the potential for in situ stresses. Geographical data, including the natural and societal conditions, are evaluated for their effect upon the mining method, and finally, economic data, basically defined as the value of the ore in the ground, but more specifically, including grade of mineable ore, distribution of ore grade throughout the orebody, and metallurgical recovery, will have a bearing on the nominal method selected. Preliminary evaluation of these factors will result in the elimination of the obviously inappropriate mining methods, leaving some method or methods for further, more detailed study. Since ore does not occur in simple geometric shapes, the method selected for more detailed study will require some variation to the standard. A few key factors will bear heavily on the selection and provide a basis for the most realistic choice. Geological Data The configuration of an orebody defined by the horizontal and vertical dimensions, the dip and strike, and the possibility of repetitive occurrences will have the major influence on the selection of the mining method. For bulk mining methods, the dip of the orebody should be steep, or the orebody must be thick so that gravity can be utilized to deliver fragmented ore to a central gathering area. Geotechnical Data The geotechnical data will be studied in greater detail when the nominal mining method has been selected and the engineering evaluation is undertaken. However, some basic initial information must be available. The structural strength of the ore and host rock, including the effect on it of faulting, fracturing, and insitu stresses, must be known. Data from exploration drilling and examination of drill core will assist in the preliminary assessment of these factors. Highly fractured ground may suggest a caving method of mining for certain orebody configurations, whereas highly competent or strong ore might indicate that for a similar configuration, longhole sublevel stoping will more likely succeed. Data obtained on groundwater from exploration drilling will be considered to determine if it can be controlled, or if it will represent a long term major expense or a hazard for which no control is possible.

Jan 1, 1981

By J. F. Gormley

Drill pipe, and the connections used to join the pipe together, have had a long history of development and improvement. With the growing use of high tensile-strength pipe, the rotary shouldered connections used to join the lengths of drill pipe have become more critical. Fatigue-type failures of rotary-shouldered connections, or tool joints, have become a cause of much conern to operators and manufacturers. Most fatigue tests on tool joints have been made on the basis of bending moment applied vs number of cycles, rather than on the basis of stress vs cycles. A desire to learn more about the nature of stress in a tool joint due to bending caused a rather intensive experimental study to determine what actually happens to cause fatigue failure. It was known that a tool joint with insufficient make-up torque was subject to early fatigue failure. Therefore, the establishment of the relationship between make-up torque and allowable bending moment would enable a testing engineer to better correlate the results of various tests. The problem of calculating the stress in a tool joint due to an applied bending moment was complicated by: the effect of unknown stress concentrations; the applicability of the well known formula S = Mc/I; and the question of whether to use the combined cross section of the pin and box in calculating the moment of inertia I. TEST EQUIPMENT The test equipment consisted of the following. 1. A lathe modified to act as a fatigue machine for full-size tool joint or drill-collar specimens. 2. An adapter plate bolted to the headstock of the lathe and into which a short adapter was screwed. 3. Tool-joint pins on sections of drill collars bucked into the adapter. 4. A hydraulic load cylinder which rested on the bed of the lathe and applied bending moments to the joints. 5. Paper-backed strain gauges (FAP-12-12, 1/8-in. gauge length and A-5-1, 1/2-in. gauge length). 6. Eastman 910 contact cement for bonding gauges to joint and Epoxylite 222 waterproofing. 7. A 12-position switchbox, SR-4 bridge balancing unit connected to an SR-4 strain indicator to read the gauge output. 8. A four-channel Sanborn recorder, Model 150, was used as the readout instrument for part of the testing. The fatigue machine was well suited as a loading device. Because of the long lever arm available, the change of moment with distance was small; consequently, the vertical shear stress was small, less than 300 psi. Some difficulty was experienced with the hydraulic load cylinder at high bending moments due to leakage. The strain gauge equipment was simple and quite reliable. A 41/2-in. extra hole (E. H.) joint with "as machined" threads and shoulders and a 2 7/8-in. internal flush (I. F.) joint with copper-plated threads and shoulders were selected for testing because of their common usage in the field. In addition, the 4 1/2-in. E. H. was suitable because it had an inside diameter large enough to permit the insertion and accurate positioning of strain gauges without using special jigs, while the 2 7/8-in. I. F. joint required much lower bending loads to cause separation of the shoulders of the joint when made up to the recommended torque. The joints were made to standard API specifications, except for very small bevels on the box and pin shoulders and cylindrical stress-relief grooves added to the pins. Larger bevels would have

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well's drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well's limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well's cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well's drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By J. Lemish

Considerable research has been conducted in Iowa in recent years on carbonate aggregate reactions in concrete. Groups outside the state have become active in the past few years after recognizing that certain carbonate aggregates are reactive in concrete. The paper reviews the nature and extent of the problem and a summary is given of research by the author and his associates. In recent years considerable research has been conducted in Iowa on carbonate aggregate reactions in concrete. The research is part of a general study on the behavior of carbonate rocks as concrete aggregates sponsored by the Iowa State Highway Commission. Research on carbonate aggregates has not been extensive in the past. Laughlin1 published one of the first papers on carbonate aggregates in 1928 and was followed by others, notably H. S. sweet,' B. Mather et al.,3 and K. Mather4 who emphasized the petrographic and physical aspects of carbonate aggregates. The recognition that certain carbonate aggregates are reactive in concrete has led to increased participation in research in the past few years by groups outside of Iowa. Significant contributions have been made by Swenson and Gillot,5 Hadley,6 and Chaiken and Halstead7 in work which emphasizes the expansion of carbonate rocks in alkaline environments and the reaction of carbonate minerals or dedolomitization with alkalies. It is the purpose of this paper to review briefly the nature and extent of the problem and present a summary of the research by the author and his associates. EXTENT AND NATURE OF THE PROBLEM The problem is the deleterious behavior of certain carbonate aggregates in concrete. It was first recognized in Iowa over 20 years ago when poor service records of certain highways were correlated with aggregates produced from the Glory and LeGrand quarries. Deleterious behavior of carbonate aggregates have been reported in Canada and, more recently, in New York and Virginia. As more knowledge is gained concerning the problem, distress in concrete related to carbonate aggregates may be recognized over a widespread area. The problem may potentially exist in the Midwest, the Northeast, and other parts of the country underlain by thick sections of carbonate rocks readily available for utilization as aggregates. The nature of distress in Iowa highways is a general weakening and deterioration of concrete characterized by progressive cracking and spalling away from joints and edges (Fig. 1). The distress generally occurs after 15 years of service and becomes progressively worse. Specimens of such concrete lack the toughness of sound concrete and break easily under the hammer in the manner of a soft brick. The matrix is generally highly carbonated and dark borders, or reaction shells or rims outline the argillaceous carbonate aggregate fragments (Fig. 2). Cracks observed in cores cut across the aggregates and concrete matrix. Although localized volume change (expansion) is associated with spalling, there is no definite field evidence in Iowa that excessive growth of concrete slabs has occurred. The experience with carbonate aggregates in Iowa indicates that the concrete deterioration is not the same as that induced by the alkali-aggregate reaction associated with siliceous aggregates. The principal difference is that in Iowa the distressed concrete is weakened throughout the slab. In concrete affected by the alkali aggregate reaction, the

Jan 1, 1961

By Tell Ertl

The term oil shale is defined. Foreign oil-shale developments are outlined briefly. The richest and most extensive oil-shale deposits in the United States lie in western Colorado. The Bureau of Mines is opening two adjacent areas for underground mining. in western Colorado. From the first area the oil shale is mined selectively as required by the retorting plant. The second area is being developed as a unit of a full scale oil-shale mine to ascertain the most practical methods of mining oil shale and to determine costs. In both of these mining areas, research will be carried on to develop new and improved practices for mining oil shale. Introduction Oil shale is a sedimentary rock containing a solid mineraloid of indefinite composition known as kerogen. On heating oil shale, the kerogen undergoes thermal decomposition and some of the vapor products of the decomposition can be condensed as shale oil. Oil from shale can be a major source of liquid fuels since extensive deposits of oil shale are known to exist throughout the world. The United States considers the establishment of an oil-shale industry only when doubt exists of the adequacy of the domestic supply of crude petroleum. On the other hand, oil shale is not strange to foreign oil men. The industry is an old one in other parts of the world. The French industry has been in existence since 1838, the Scottish since 1859, the Australian since 1860, the Estonian and Swedish The since World War 1, and the Manchurian industry since 1929. The most highly exploited oil-shale deposits are the Carboniferous shales of Scotland. About 20 seams ranging from 4 to I2 ft in thickness are worked. The yield during recent years in scotland has been 18 to 25 gal of shale oil per ton, from 3&"30'000 tons per year' The French and Swedish oil-shale deposits are of lower grade than the Scottish. The Estonian oil-shale deposits are 7 ft thick, and the oil yield averages 50 gal per ton. Over 1,000,-ooo tons are mined each year, half of which is used directly as fuel to substitute for coal and the other half is used for the production of oil. Immense deposits of oil shale that will yield 10 to 15 gal per ton exist in Germany. Because of the impending loss of the Rumanian and Polish oil fields and the bombing of synthetic liquid fuel plants, the Nazis in 1943 started a large-scale oil-shale program in Germany. By V-E Day, it is said, oil-shale production had reached the rate of 2500 tons per day and rapid expansion of the industry was imminent. Australian oil shale, known as torbanite, occurs in beds 2 to 6 ft thick. It is of a very high grade and on retorting yields 80 to 160 gal per ton. The oil-shale industry of Manchuria was the largest in the world during the past decade. The well-known Fushun coal deposit in Manchuria has an overburden of 500 million tons of oil shale about 450 ft thick that will yield 10 to 15 gal of shale oil per ton. The oil shale is

Jan 1, 1949

By R. N. Thurston, E. A. Nesbitt, G. Y. Chin

A general relalionship between the amount of glide shear (due to slip) and the macroscopic shape change has been developed. Since the deformation can be large, finite strain analysis is employed. In this treatnzent, the shape change is expressed by a deformation gradient matrix, F - [axi/aXj1, where X and x refer to the initial and final positions of a particle. This matrix is readily evaluated in terms of the amounl of glide shear, a , and the direction cosines of the slip-plane normal and the slip direction for a single active slip system. In the case of deformation from slip on several systems, the product F(a) of the several deformation gradient matrices is first calculated. Then, by assuming that the final configuration is reached by a long series of small shears of magnitude a, occurring more or less alternately in the several slip sys- IN problems of crystal plasticity, it is often necessary to relate the amount of glide in the operating slip systems to the macroscopic strain components. This relationship is relatively simple when only small strains are considered. In this case the separate strain contributions from several slip systems are additive. Such a procedure is incorrect in the case of large plastic deformation. To the authors' knowledge, no general treatment of the latter problem has appeared in the literature. In specific instances, Mark, Polanyi, and schmid3 have derived the relationship between glide and axial elongation during tensile pulling of a single crystal when only one slip system is active. A similar relationship for duplex slip was worked out by v. Goler and Sachs.4 Taylor and Elam5 have also studied in detail problems of large plastic deformation. Due to uncertainties as to the slip systems at the time, terns, the final deformation gradient matrix can be obtained. Mathematically, the problem is reduced to finding the limit of F(dN as N — m while a — 0 in such a way that the Product Na = 0, a ftnite conslant designatzng the accunzulated amount of shear. It turns out that this limit is simply , where F, is the matrix whose elements are the coefficients of a in the F(a) matix. Application is made of the present treatment to a fcc crystal of Perlrzalloy compressed on the (110) plane and contrained to elongate zn the [112] directzon. In addition, it is shown that one rnay readily obtain from the general analyszs the well-known formulas relating elongation, amount of glide shear, and amount of lattice rotation for crystals deforming by single and double slip under tension. however, they were mainly concerned with proving that slip occurs on {111}(110) systems in fcc metals. The present general treatment arose out of recent investigations of magnetic anisotropy in cold-worked Fe-Ni alloys6 as well as some related problems in strength anisotropy of single crystals.' Detailed application of the general analysis will be provided in the case of a Permalloy single crystal compressed on the (110) plane and constrained to elongate only in the [112] direction. It will be seen that, as expected, the small strain approximation leads to significant errors after moderate straining. It will also be shown that the present general treatment yields the formulas of Mark et al. and of v. Goler and Sachs in those specific cases. GENERAL CONSIDERATIONS Consider a homogeneous deformation in which a material point initially at moves to both positions being referred to the same set of Cartesian axes. Such a deformation can be

Jan 1, 1967

By W. G. Bearden, G. C. Howard, J. W. Spurlock

An investigation of the factors af-fec.ting the inter-zonal flow of fluids in the casing-wellbore annrc1rt.s of an oil or gas ivell is presented Laborntory tests revealed that failure of the caring-cement bond allows communi-cation of fluid at pressure differentials near 1.000 psi. Perforating with a 11011011: carrier gun does not shatter or crack the cement sufficiently to allow communication through these cracks and does not seriously affect the casing-cement bond failure pressure. The pressure to cause communication at the casing-cement bond can he increared to 3,000 psi by. limiting pipe deformation during cementing and subsequent operations. Communication can be prevented, however. up to pressures sufficient to cause the cement to fail or the casing to col-lapse, by attaching to the casing a seal ring of deformable ruhber molded between two steel flanges. When installed, one flange is attached rigidlv to the casing to serve as back-up for the gasket While tile other flange is movable. To date, these gasket seal rings have been field-tested in 27 Wells. Althotrgh communication has been noted in two wells, inter-zonal flow has been prevented in other wells in the same area by installing more seal rings between the communicaring zones. INTRODUCTION The inter-zonal flow of fluids behind casing cemented in oil wells during normal production or stimulation operations is a major operating problem. If it cccurs during production operations. it can seriously limit the pressure to which a reservoir may be depleted without harmful invasion of unwanted fluids. If it occurs during stimulation operations, it may preclude the possibility of stimulating the desired zone. This communication can be caused by failure of the bond between the casing and cement, failure of the bond between the cement and formation, or failure of the cement itself. This paper presents the results of an investigation of factors affecting com-munication at the casing-cement bond and methods which aid in preventing it. LABORATORY INVESTIGATIONS The laboratory tests performed in this study were divided into three phases. The first phase consisted of tests to determine if perforating would shatter and crack the cement sheath so severely that communication would occur through the cement itself. The second phase consisted of tests to determine more precisely the cause for the casing-cement bond failure. The third phase consisted of tests to evaluate the effectiveness of various de-formable seals attached to the casing in preventing communication. EFFECT OF PERFORATING, The effect of perforating was invest~gated in tests performed with apparatus shown on Fig. 1. Cement was poured into the annulur space hetween 5%-in. casing and 8%-in. casing and allowed to cure for 72 hours. The apparatus was then perforated with a hollow carrier gun containing eight duPont 26-A shaped charges. Bull plugs were placed over the perforations in the 8 5/8-in. casing and hydraulic pressure was applied inside the 5 1/2i-in. casing. The pressure to cause fluid communication past the cement sheath was observed and termed the "bond failure pressure". Several different cement compositions were included in these tests, the results of which are shown in Table 1. In Tests 1 through 4 of Table 1, bond failure occurred at- the inter- .

Jan 1, 1966

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter's tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.' The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"', an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By C. D. Wiseman

THE concept of alloying to increase the strength of metals originated during the bronze age. However, at the present time there is no single theory capable of explaining all of the observed strengthening effects of alloying elements on the mechanical properties. In general, it may be said that solid solutions are stronger than the pure metal and that the strengthening effect increases with increasing alloy content. Various theories for solution hardening have been proposed, the first of which was presented by Rosenhain who suggested that the alloying elements roughened the slip planes, thereby requiring a higher stress to initiate slip. Recent work by French and Hibbard2 confirmed Norbury's3 conclusion that those alloying elements which cause a greater change in lattice parameter have larger effects on hardness. However, a given change in lattice parameter produced by different alloying elements does not cause the same change in hardness. A further refinement was suggested by Dorn, Pietrokowski, and Tietz4 who considered differences in valence between the solute and solvent with the change in lattice parameter to explain the plastic properties of aluminum alloys. Allen, Schofield, and Tate5 further investigated the valency contribution to solution strengthening by testing some copper-base solid-solution alloys having constant electron densities. Tensile tests performed on these alloys gave identical stress-strain curves even though the atomic size effect, which varied by a factor of two, was neglected. The advent of dislocation theory6-8 provided a new and powerful tool capable of explaining many phenomena of plastic deformation and indicated new approaches to solution hardening. The basic con- cept of recent theories is that solution hardening is not due to stresses associated with randomly dispersed solute atoms, but rather to a nonuniform distribution of the solute. This conclusion was reached by consideration of the effective tension present on each dislocation line and the ability of a dislocation to pass an obstacle. cottrell suggested the possibility that the internal stresses due to randomly distributed solute atoms would offer essentially no resistance to the passage of dislocations. He reasoned that an edge dislocation may be considered as a rigid line discontinuity. As the dislocation moved through a crystal, the random stress fields would be equally distributed along its length. Since half of the stress fields would be acting to move the dislocation forward and the other half trying to move it back, the net effect on the dislocation would be zero. Thus the randomly distributed solute atoms would not contribute appreciably to solution strengthening. Mott and Nabarro10 considered the dislocation as a flexible, rather than a rigid, discontinuity. They obtained a simple model for a dislocation moving in a lattice having precipated particles, where the dislocation would actually bend around the obstacle until it would loop back onto itself to rejoin and then continue onward. Their work indicated that the minimum radius of curvature of the dislocation line, under the action of an external stress and in the region of an internal stress, would be such that the dislocation would be unable to pass through a matrix containing small closely spaced precipates by the looping process. The dislocations would tend to remain rather straight, approaching the condition of Cottrell's rigid dislocation. Hence, the strengthening must not be due to random solute atoms; however, it might be due to the concentration of atoms, either as clusters of like atoms or as short-range ordered regions, or to the concentration of solute atoms around dislocations. To date, four mechanisms of solution strength-

Jan 1, 1959

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

A. MALINOVSZKY,* Belleville, Ill. (written discussion?).-I have been very much interested in Mr. Dolman's paper. We all realize, I think, that this question of developing our home industries and support-ing the new industries which have developed during the great war is very important at present. Mr. Dolman has well shown the quantity and quality of the raw magnesite in the United States, and the commercial and industrial possibility of our home magnesite and I believe, with him, that our home industries should receive adequate protection. There are two reasons, however, for believing that this may be difficult. One reason is that much American capital is invested in the Austro-Hungarian magnesite industry. The raw magnesite can be quarried and prepared for the market in Austria with much cheaper labor expense than in the United States; large deposits which are very easy to quarry and good transportation facilities also contribute to the cheapness of production. The second reason is the old saying that the magnesite found in the United States is not of the same quality as the Austro-Hungarian mag-nesite; this I doubt. Even if the magnesite found here does not in a raw state equal the Austro-Hungarian, it can be synthetized so that the finished article will have the same properties as the Austro-Hun-garian finished magnesite refractory possesses. Thaw magnesite from Greece is not the same as the. Austro-Hungarian, but it has linen demon-strated that a good refractory can be made from the Greek product.

Jan 10, 1919

By O. B. Hopkins

DuRing 1931 Peru lost its place as ninth among the oil-producing countries of the world, to Argentina, and even in tenth place its production only slightly exceeded that of Trinidad. The preliminary figures for 1932 indicate that Peru will lose tenth place for that year to Trinidad. The production in barrels of the three coastal fields of Peru during the past three years was as follows: In addition to this crude production, the International and Lobitos companies produced approximately 770,000 bbl. of casinghead gasoline during 1932. There was no outstanding development in the oil industry in Peru during 1932; activity in the fields was very much restricted due to curtailment of production and the low price of oil. The potential production of the property of the International Petroleum Co. Ltd. greatly exceeded the actual production. By the beginning of 1932, a total of 2348 productive wells had been drilled on the property of the International, of which 547 had been abandoned, leaving 1801 productive wells at that' date. These wells cover a total productive area of approximately 13,500 acres. The crude produced has an average gravity of 37° to 38° Be. The Lobitos crude is of approximately the same gravity. The earliest oil pool developed in the Peruvian Coastal area is now more than 40 years old and is still producing. The major development in the area took place between 1920 and 1930. Production at the present rate can be maintained for 10 years or more.

Jan 1, 1933

By F. A. Hill

Coal mining in the State of Washington offers many interesting problems for the mining engineer, due to the varied physical conditions occurring in different fields, and often in the same mine. The different coal seams worked in the same mine commonly require different mining and transportation methods for economical operation. The coal measures have inclinations ranging from 5' to vertical, and in the same mine the dip of the coal may vary from 30' to 50 . In all fields, the seams are extensively faulted, folded, and sheared. The quality of the coal produced ranges from brown lignite to bituminous coking coal, the following being typical analyses: Very little of the coal contains as much as 0.75 per cent. sulfur. The brown lignites occur mostly in Lewis and Thurston Counties, and as a rule are very cheaply mined. This coal has been successfully used in locomotives of the Oregon & Washington Railroad, after equipping them with specially designed fireboxes. The sub-bituminous coals occur in all the coal-mining counties. Their cost of production varies widely, according to the character of the formations, the pitch, and the wall conditions. This makes a fairly good steam coal, but the lump is used mostly for domestic trade, after grading into lump, nut, and pea. The coking coal is used for making coke, and for locomotive and other boiler fuel. It yields a strong metallurgical coke, quite high in ash, though seldom exceeding 18 per cent. ash. Most of it is susceptible to

Jan 1, 1920

By L. G. Huntley

Points out differences between the new, more liberal, law passed by the Colombian Congress and the law passed in 1919, gives a few facts about the pipe-line concession granted to a Canadian company, and tells of new drilling developments. PROBABLY the most important development in the Colombian oil situation during the past year was the passage by Congress of a new petroleum law, which went into effect Jan. 31, 1923. The principal points of interest in which this new law changes or improves the previous one are as follows: Law 120 of 1919 provided that one person or corporation could not acquire more than three exploitation zones. of 5000 ha. each, and royalties were based on a sliding scale, to wit: 6 per cent. royalty on lands 400 km., or more, from the ocean; 8 per cent. on lands 200 but not over 400 km. from the ocean, and 10 per cent. royalty on lands located less than 200 km. from the ocean. Rentals were fixed at 10 centavos per hectare for the first year; 20 centavos for the second year; 50 centavos, third year, and $1 (one peso) yearly thereafter. Under this law the term of the lease was fixed at 20 years and, at the discretion of the government, could be extended for 10 years additional. After the expiration of the lease and its corresponding extension, the machinery and other material placed upon the property would vest in the government. A bond of 20,000 pesos was also required of the lessee to guarantee faithful performance of his contract.

Jan 3, 1924

By I. Iwasaki

In the flotation of iron ores and nonmetallic ores desliming is the key to a successful operation; the technology of flotation of well-deslimed ores has become fairly well established. When finely disseminated ores are ground to liberation, however, conventional desliming of the fully dispersed pulp results in an excessive loss of valuable constituents. Selective flocculation of iron oxides followed by removal of dispersed siliceous slimes is a new development and is one of the most promising approaches to the treatment of finely disseminated, oxidized iron ores, available in vast quantities both here and abroad (1,2,3). To apply selective flocculation to the variety of refractory iron ores or to cope with the fluctuations in an individual ore and the make-up water, the factors governing this technique must be clearly formulated. For the removal of siliceous and clayey slimes from oxidized iron ores by selective flocculation, the optimum conditions are extremely sensitive to the mineralogical characteristics of the ore, the type and the amount of soluble salts in pulp solutions, and the mesh-of-grind. Certain starches appear to function better than others (4, 5). Selection of the proper reagents and their judicious use is important not only for their efficient utilization but also for minimizing the adverse effects they might exert on the flocculation and flotation steps, and the pollution the effluents might cause when discharged, either intentionally or accidentally, into lakes and streams. In the present article some of the major factors that influence the selective flocculation of iron ores are summarized.

Jan 1, 1979

By C. B. Jordan

LAVES and Wallbaum' have described TiRu and TiOs as having the same structure as TiFe; they had previously described the latter compound as having the CsCl structure. On the other hand, a careful investigation of the structure of TiFe by Duwez and Taylor- ailed to reveal the ordered CsCl structure, finding instead a random arrangement of titanium and iron atoms on the points of a body-centered-cubic space lattice. Consequently, it is not clear whether Laves and Wallbaum proposed the ordered or the disordered structure for TiRu and TiOs. In order to settle this question as to the structural type and to obtain values of the lattice para- meters (thereby completely determining the structures), the present investigation was undertaken. Samples having the compositions TiRu and TiOs were weighed out accurately from iodide titanium supplied by the New Jersey Zinc Co., ruthenium powder from Goldsmith Brothers Smelting & Refining Co., and osmium powder from Wildberg Brothers Smelting & Refining Co. No analysis was made of any of these metals. According to the respective analyses of the suppliers, total impurities amount to less than 0.03 pct in the titanium and to less than 0.5 pct in the osmium. The purity of the ruthenium is not known. The alloys were prepared by arc melting in a furnace of the type described by Schramm, Gordon, and Kaufmann.9 pecimens for X-ray diffraction were obtained by crushing the ingots and passing the resulting powders through a 200 mesh screen. Diffraction patterns were made with a powder

Jan 1, 1956

By F. Weinberg

WHEN impure Zn (< 99.99 pct)&apos;&apos;Z or Zn-Cd alloys3 are progressively solidified, a cell or "corrugation" substructure4 is produced in the solid, with a high impurity or solute concentration along the cell walls. When these materials are polished and suitably etched, etch pits are often observed along the cell walls. For the Zn-Cd alloys these etch pits have been associated with decorated dislocations, present in the corrugation boundaries to accommodate the lattice strain. In the course of an investigation of Zn-2 pct Au alloy, molten metal of this alloy was poured into cold water and the resultant solid pieces were sectioned, polished and etched with a Cr0 ethant. An extremely regular cell pattern was observed on the etched surface, similar in general to the corrugation structure previously reported for impure zinc and Zn-Cd alloys. At higher magnification, regularly spaced pits were observed along the cell boundaries. An example of the regular cell pattern at the center of a specimen is shown in the center and lower portions of Fig. 1; the top of the figure shows the pattern near the specimen surface. Typical etch pits in the cell walls are shown in Fig. 2. It was surprising that a cell pattern as regular as that shown in the center of Fig. 1 was produced at the very rapid solidification rates used (estimated as > 1 cm per sec). In addition, the distribution coefficient for the Zn-Au system is greater than 1. Accordingly, the center of the cells should be rich in solute and should etch

Jan 1, 1963

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from &apos; &apos;paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

By Bernard Rachlin

IN the mineral industry measurement of density or specific gravity of slurries is often necessary or highly desirable. To date the most successful method of measuring the specific gravity of various media is to hand weigh a constant volume sample of the slurry. This method is time-consuming, however, and is intermittent rather than continuous. Most density measuring instruments in use today are variations of three basic systems: air bubble tube systems, radioactive methods, and displacer systems. The high cost of the radioactive cell, combined with the precision electronic measuring that is required, limits the practical utility of this procedure to a small percentage of critical processes. In the air bubble systems clogging of the bubble tubes with solids has rendered this type of measurement completely ineffectual for many applications. Continuous or intermittent purging of the bubble tubes with air or water to prevent tube clogging has been tried but has not been very successful, especially in the heavy media process. The displacer system, which presents the fewest complications of all the density measuring systems, consists only of a metal immersion unit and a means of weighing it. In the past, settling of the solid in the slurry has caused untrue samples and clogging of the media at the bottom of the chamber. It is also important to dampen excessive flow surges such as those caused by reciprocating pumps. The system described here successfully overcomes these difficulties. Description of the Process System: The process equipment, on which the field tests were run, was a

Jan 1, 1957