Search Documents

By A. C. Callen

This, report represents the comments of the individual members of the A. I. M. E. Sub-committee on Physics of Mine Ventilation on the proposals of a special committee of the Institution of Mining Engineers (London). As might be expected, there is a certain diversity of opinions, for owing to the shortness of time- it was not possible for the sub-committee to get together for informal discussion. The report is presented in this form in the hope that it will bring out a full discussion by other members in the Institute. OLE SINGSTAD?, New York, N. Y.-The Atkinson formula, P =SV2 K a is quoted and it is stated that this formula is especially applicable to mine galleries but is unwieldy in application, as in many problems the value of K, S and a are assumed not to change. This is the same formula that was used during the preliminary calculations for the ventilation of the Holland Tunnel, and where the above-mentioned values were constant for a number of cases, it was a very simple matter to rewrite the equation n the form P = K1V2 and avoid the repeated use of identical figures. The Atkinson formula assumes 1. That resistance to flow is independent of the pressure. 2. Changes in volume due to change in pressure may be neglected. 3. Changes in density and viscosity may be neglected. 4. That the coefficient K is a constant. 5. That P is proportional to V2. We found, from our experiments in connection with the ventilation of the Holland Tunnel, that all the above assumptions could be safely made, with the exception of No. 3, and No. 4 at, very low velocities. In mine work, where many assumptions must necessarily be made, it would seem inconsistent to attempt to make any allowance for the other factors, which are so small that they can be determined only by the most careful experimental work. However, P does depend directly on the density of the air, and to that extent the Atkinson formula is incomplete.

Jan 2, 1926

By R. O. Neal

There are two main sources of the water that floods productive oil or gas sands. The water may rise from the lower depths of the producing stratum, or it may come from beds above or below the oil-bearing formation. Usually the recovery of oil is decreased by water entering the oil sands, and most oil-field waters, especially those of deep wells, tend to foster the formation of an emulsion, which is expensive to treat. This paper deals with a method of distinguishing between waters that encroach upon oil-bearing beds from sources in the same stratum and waters that reach the oil sands from horizons above. In order to remedy effectually water difficulties in oil and gas wells, it is absolutely necessary to determine the source of the invading water. Sometimes evidence such as the structural relations between the strata penetrated by deighboring wells and those found in the well under investigation is not adequate; also, data from drill logs and well records, from mechanical tests made on the wells by plugs, testers, drilling tools, etc., and from tests by chemical indicators such as eosin and Venetian red, may be unsatisfactory, for such data may fail to locate the source of the infiltrating waters. As a resort in such cases, the application of chemical analyses, that is, the comparison of an analysis of the water in question with that of typical waters from the various water horizons in that particular district, has in certain instances proved of value. This method has been used to advantage in the Westside Coalinga field of California, where the source of water may be fairly definitely determined , from its composition. The chief conclusions concerning the chemistry of the oil-field waters in California by G. S. Rogers1 are: "Oil-field water is not necessarily salty, as is generally believed, and may not be even slightly salty to the taste. The degree of concentration of chloride in such water is governed primarily by local conditions and is not affected by the position of the water in relation to oil. Sulfate diminishes in amount as the

Jan 1, 1920

Andes Copper has an old camp and a new camp, both isolated until recent road improvements. The old camp is at Potrerillos and the new one at El Salvador, 25 road ,miles away. The company was incorporated in 1916 and the first mine, concentrator, leaching plant, smelter and town were built in the succeeding twelve years. The first blister copper was poured on January 24, 1927. Economic conditions determined the long development period but the end result was the design and construction of a mining complex that was all of a piece, unlike the piecemeal additions to El Teniente and Chuqui. The mining episode at Potrerillos came to an end in 1960 when the ore at La Mina became exhausted and the new mine, El Salvador was brought in. Both of these ore deposits come within four hpundred feet of the surface and had they been developed within the last five years might reasonably have been brought in as open pit mines. However, that is conjecture, and as it stands the operation at La Mina was so ideal for the mining method selected, blockcaving, it became a classic for the textbooks. On the other hand, El Salvador has turned out to be a blockcaving mine to test an engineer's skill. In mining the copper deposit at Indio Muerto mountain, there are ground conditions of every conceivable type. Tunneling in one section, the back can cave like sized pea gravel and only spiling can hold it; in another heading only the lifters are shot but often the rest of the round will sit down in one piece; elsewhere the bottom squeezes up and closes the drifts; and contrary to all other locations, there are sections where the block can be undercut without support. Today the scope of operations at Andes extends from mining to electrolytic copper. Ore is mined at El Salvador and the concentrator is also situated there. Concentrates pipelined 14 miles to Llanth, the water decanted, and then it is hauled by rail 40 miles and 5500 ft higher to the Potrerillos smelter and refinery. Potrerillos and El Salvador are respectively 90 and 70 miles from the port of

Jan 11, 1969

By Clarence W. Balke

Small buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreciable size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. Pressing the Powder With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numerous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects due to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

By Raymond Howe

SOME time ago,, a prominent engineer asked a representative of the firebrick industry to prepare a comprehensive paper on blast-furnace refractories. It was to have been the purpose of this paper to gather practical experiences from widely different sources, in the hope of determining what kind or kinds of firebrick were best adapted for certain uses. This engineer sent questionnaires to the large consumers of blast-furnace linings and stovebrick and received very detailed replies as to their experiences. These replies are conflicting, but, having been turned over to the writer, form the basis of this attempt to meet the request. Because of the impossibility of making final recommendations at this time, a few of the more interesting and commonly known methods of studying refractories are also discussed, as well as the more recent developments in this field. The first reply to, the questionnaire stated that good service was being secured from the linings. This satisfactory condition was attributed to the use of a very good distributor. The writer believed that manufacturers try to and do produce a good product and that the proper handling of equipment is of the utmost importance, if good results are to be secured. The type of bricks used was not mentioned. The second reply stated that good life was secured from the furnace linings, but that the writer had had soft-fired stovebrick crumble and, for that reason, preferred a hard-fired product for use in this position. The type of bricks used was not mentioned. The third reply stated that firebrick had crumbled from the mantle up; the cause was not known. The fourth reply stated that the stove linings were satisfactory. Hand-made furnace linings failed after 4 years' service so a steam-pressed lining was installed which was still good after 4 years of service. Consequently, a second steam-pressed lining was installed but this disintegrated at the top after the furnace had been in- blast 7 months. The firebrick manufacturer attributed this failure to the expansion of iron blocks that had been installed at the stock line to prevent erosion.

Jan 9, 1919

By Richard Moldenke

So far as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in excep tional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and for the production of commercial steel. As the foundry is often compelled to draw upon the pig irons made for steel purposes, for economic reasons, whereas the steel industry does not draw upon foundry pig irons proper, the situation is resolving itself into one of grave consequence for the life of the gray-iron castings industry, and hence the intensive present-day feeling in foundry circles for rigid specifications to govern the quality of pig irons sold for foundry use. In the discussion of a paper on the use of scrap in the blast furnace held recently in the Institute, a very pertinent remark was made by one of the participating furnacemen, who confessed that "the things found wrong by the foundryman with his iron were beyond his depth." It may be added that those things are also beyond the depth of most foundrymen who, however, know from their results that they are getting poorer castings today with many pig irons than they did with those same brands in former years. Under the former fracture buying, the foundryman at least could select the strongest metal, as judged by the sledge, from various brands of similar fracture and pig section, and his results proved

Jan 1, 1927

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By Cecil H. Desch

The progress of metallurgical practice and the demands made by the engineering industry on our foundries and mills have made the crystalline structure of metals a subject of far more than academic interest. Metals and alloys are made up of crystals. Even if we accept the view, so ably maintained by some metallurgists, that the crystals are separated from one another by an amorphous layer, it remains true that all but a very minute fraction of any metallic mass is crystalline. The conditions which affect the growth of crystals are therefore of importance in metallurgy. It is not only castings whose properties depend on the arrangement of their crystals, for the more we learn of the behavior of forged, rolled and drawn metals, the more certain it becomes that it is profoundly influenced by the size and arrangement of the crystals in the original ingot, determining a structure which may persist in a modified form through a long series of mechanical operations and annealings. This is mainly due to the concentration of much of the impurities in the last portions of the liquid to freeze, so that the boundaries between single crystals or groups of crystals are marked out by a zone of segregated material, differing in properties from the mass, and offering a barrier to diffusion and equalization of composition throughout the whole. The importance of this fact has been fully recognized by steel manufacturers, who have to deal with ingots which are sometimes very large, and are cast at a high temperature, containing impurities which have a marked effect on the properties even when present in very small quantity. For this reason the Iron and Steel Institute has set up a committee to examine the whole question of the heterogeneity of steel ingots,(1)† and a report has been issued, containing an account of the structure of 16 ingots, ranging in weight from 15 cwt. to 172 tons, each of which was sectioned and examined by chemical analysis and by etching. A valuable body of data concerning segregation has thus been collected. The work of the committee is being prosecuted with great activity, and at the same time researches are in progress to determine the physical

Jan 1, 1927

By Thomas Brownfield

The chronicle of the oil industry in Oklahoma in 1939 is one of declining production bolstered by strenuous efforts to find new pools or new producing horizons in the older, highly exploited, relatively shallow areas. Production, which averaged 608,000 bbl. daily in 1937, the post-depression peak, declined to 463,000 bbl. daily in 1938 and continued downward to 421,000 bbl. daily for the year 1939. While the state could produce somewhat more oil if demand warranted it, production in most areas is at as great a rate as could be justified on the basis of maximum efficient operation. Outlet for Oklahoma crude has been seriously affected by the increase in production in the Illinois Basin. Crude movements from the Kansas-Oklahoma area to the northeastern consuming centers averaged 314,000 bbl. daily in 1939 as compared with 397,000 bbl. in 1938. Oklahoma producers bore the brunt of this loss of market. The general production decline was accentuated by the August, shutdown of 15 days, precipitated by the action of a major crude purchaser posting a 20-cent reduction in the price of crude. The Oklahoma Corporation Commission, in collaboration with other members of the Interstate Oil Compact Commission, ordered a complete shutdown of all producing wells in order to prevent the premature abandonment of stripper wells, which might result from a prolonged period of production at prices below operating costs. The reduction in price was forestalled, most major purchasers failing to meet the cut in view of the shutdown, and the company initiating the move rescinded its action. Fear of the shutting in of oil wells, especially those making considerable quantities of water, is generally unfounded in the light of a superficial examination of the records. Oklahoma's unprorated pools, which produced 154,000 bbl. daily in May, declined to 152,000 bbl. in June and 143,000 bbl. in July. Immediately following the shutdown, the same pools produced 150,000 bbl. in September, 145,000 in October, and 145,-000 in November. Thus, while the half month's production loss in August has not been made up, the wells apparently hare produced at a greater rate since the shutdown than immediately preceding it.

Jan 1, 1940

By H. Rush Spedden, A. M. Gaudin

ALTHOUGH the number of minerals that are ferromagnetic) or highly paramagnetic is strictly limited, it has been known for some time that many minerals have slight but supposedly characteristic magnetic susceptibilities. With the exception of pyrrhotite, however, sulphides have been thought nonmagnetic. A new magnetic separator has been made available recently in limited quantity to research laboratories. This device, the Frantz Isodynamic Separator, has been used for the separation of various nonsulphides from each other. Its application to the separation of sulphides, however, does not seem to have been reported. In the Richards Mineral Dressing laboratories, the success achieved through the use of this device in separating associated sulphides has been so startling as to lead us to believe that it constitutes a magnificent adjunct to heavy-liquid separation and to quantitative mineragraphy as a tool for the mineral investigator. THE SEPARATOR The separator (Fig. I) consists of: I. A powerful magnet, the strength of which can be adjusted by means of a rheostat; 2. A vibrating chute of nonmagnetic metal on which the mineral to be separated is made to flow (Fig. 2); 3. A feed bin and adjustable feeder; 4. Receptacles for the collection of products; 5. Means for changing, setting, and accurately reading the two slopes of the chute; viz., the cross slope and longitudinal slope. The separator is made operative by the special shape of its pole pieces, which ensures a strongly converging field. It is said by the makers of the machine that the pole pieces apply a constant mechanical force to a particle of given susceptibility, regardless of its position in the operating space of the separators.* Susceptible particles, therefore, behave as though of lower specific gravity than under ordinary circumstances. This effect, combined with the slopes of the chute and the action of the vibrator, causes a stratification not unlike that obtainable on a shaking table. The chute is of rectangular cross section, and shallow; it is broadened toward the discharge end and divided longitudinally by a partition into two compartments that lead to the collecting receptacles. Although the separator probably can be used to make separations at fairly coarse

Jan 1, 1943

By F. H. Willcox

In Bessemer-steel practice, air is blown through a bath of iron, or projected strongly upon its surface to burn out silicon, manganese, and cafbon. Toward the end of the blow, when the iron is not protected from oxidation by these elements and the excess of air becomes great, there is oxidation of the iron. In open-hearth practice, the same difficulty is experienced with dissolved gas and oxides in the product, though not to as great or severe a degree as in the Bessemer process because the oxidizing conditions grow less severe as the end of the heat is approached, and if the bath is allowed to boil for a time it undoubtedly frees itself from a large part of the gas and oxides which have been absorbed in the earlier part of the process. Basic open-hearth steel is usually assumed to contain a larger proportion of oxides than acid open-hearth steel, but it may be said that all steel, Besserner and open-hearth, contains more or less oxide of iron dissolved in the fluid metal at the end of the "blow" or "heat." That certain metals are solvents for their respective oxides has been shown, in the case of copper, by Heyn, and, in the case of iron, by Law. It is indicated that the solubility of iron oxide in iron increases with the purity and temperature of the metal. This confirms what is observed and known by operating men, and these observations may be summarized as follows: 1. Cast iron. is rarely subject to oxidation, as is logical from its composition. 2. Normal steel, unless deoxidizers are added, contains blow holes. 3. Steel known to be oxidized is full of blow holes. 4. The addition of deoxidizers prevents, to a greater or less degree, the formation of blow holes in normal steel. With these observations in mind, it is logical to deduce that the cause of blow holes lies in part in the presence of dissolved oxide of iron in the molten steel and its consequent reaction with the carbon of recarburizers, when these are added, to form gases. (Another factor in the origin of blow holes is, of course, the solubility of gases themselves in the steel and

Jan 1, 1917

By R. W. Parsons

wben a displacement front encounters an isolated permeability heterogeneity, it will be perturbed. The details of this perturbation will depend on the beterogeneity size and shape, the Permeability contrast, and the mobility ratio. This paper deals with the displacement front behavior for one, simple, mathematically tractable model: a circular permeability discontinuity and unit mobility ratio. The progress of an initially planar front is shown for four permeability contrasts: k2/k1 = 0, 5/2, 2, m. The front distortion is more pronounced than streamline and isopotential distortion and it approaches a constant shape downstream from the discontinuity. INTRODUCTION The impact of reservoir heterogeneities on oil displacing processes depends upon the variation of the heterogeneous property (frequency distribution), its disposition (spatial distribution), and the inherent stability of the displacement mechanism.l The interplay of these factors plus the impracticability, if not impossibility, of describing a natural rock system in any detail makes exact displacement front movements difficult to determine. It is useful, however, to be able to qualitatively visualize what heterogeneities will do to a displacement front. In this respect certain simple models that can be treated analytically are of value. The following analysis will show the displacement front behavior for one such model. MODEL DESCRIPTION The flow field is two-dimensional and infinite in extent. The fluid flow is single phase, steady state and unidirectional at x, y = 2 m, or before insertion of the discontinuity. A circular permea- bility discontinuity is placed at the origin. Porosity and thickness are the same within and exterior to the heterogeneity. This is exactly the same model that was used by Greenkorn et al. to check analytically Streamlines as determined by Heie-Shaw flow models and finite difference computer techniques.2 FRONT POSITION CALCULATIONS The results of displacement front calculations are presented in Figs. 1 through 4 for four different permeability contrasts: k2/kl = O, %, 2, m. The times corresponding to the front locations are the Same for the 0 and cases! and for the 1/2 and 2 cases. The determination of front positions at various times is based on known analytical expressions for velocity potentials ().2 and stream functions ().2 These expressions are in terms of the x and y

Jan 1, 1969

By J. S. Ross

Although the opinion has prevailed for several years that bottoni-hole choking under certain flow conditions should effect an increase in flow efficiencies, the use of bottom-hole chokes until recently has been limited in application mainly because of mechanical difficulties encountered in their construction. Within the past year, however, bottom-hole choking, through the development of a removable type of choke, has been applied successfully under various conditions of flow in many Mid-Continent fields. The observation of these field tests indicates that bottom-hole choking, although not applicable to all flow conditions, has an important place in the operation of oil and gas wells. This paper gives briefly the conclusions drawn from the data obtained from the experiments with this bottom-hole choke under various flow conditions, and a description of the choke and its operation. Purpose of Bottom-hole Choking Since, in a normal well, the velocity with which the column of gas is moving generally has a direct bearing upon the quantity of oil it can lift, probably the main purpose of bottom-hole choking is to accomplish an increase in the velocity of this- rising column, particularly in the lower portion of the tubing string. This it does first, by expansion of the free gas accompanying the oil; next, by liberation and expansion of some of the occluded gas normally carried in the oil to the surface; and lastly, by atomization, which results in a more intimate and uniform mixture of the oil and gas. It is apparent, then, that if this velocity, particularly in the lower portion of the flow string, at a given rate of production, is inefficiently low, owing either to an insufficient supply of gas or to excessive surface choking, and slippage takes place, bottom-hole choking should bring about an increased velocity of the gas and hence an increased lifting capacity. But if the velocity of the column of gas at this same rate of production through a surface choke alone is at or above a velocity necessary to lift the oil efficiently, increasing the velocity by bottom-hole choking would probably serve no useful purpose, other than to steady the flow by the better mixture of oil and gas and to lower delivery pressures.

Jan 1, 1932

By P. A. Beck, L. J. Demer

As reported in a previous publication,' isothermal grain growth in high purity aluminum and in an aluminum alloy with 2 pct magnesium can be adequately described by means of the empirical relation: Here, D is the average gain size after an annealing period 1. The annealing period includes the time for complete recrystal-lization R, and the time for gain growth 1,. D, is the pain size as recrystallized, n is a parameter depending on the temperature and on the material. The effect of 2 pet magnesium in solid solution was to decrease D, and to increase R, A and n at a given temperature. The present work was undertaken in order to investigate the above listed-effects of magnesium in solid solution, as functions of the magnesium content. The work also includes the study of certain anomalous effects observed in the recrystal-lization and grain growth of the 2 pct magnesium alloy at 350°C. Experimental Procedure The method of producing the ingots used in this work was described in detail1 and need not be reproduced here. The materials used were high purity aluminum, furnished by the Aluminum Co. of America, of lot analysis shown in Table r and magnesium from a high purity distilled stock of magnesium crystals. Table i—Lot Analysis of High Purity Aluminum Per CeNt Si.................................... 0.00~ Fe.................................... 0.002 Cu................................... 0.002 Mg................................... 0.003 Mn................................... o. oox Ingots were prepared for a series of binary aluminum-magnesium alloys of increasing alloy content. The numbers used to designate these ingots and their magnesium contents by chemical analysis are given in Table 2. Table 2—Ingot Numbers and Magnesium Contents Ingot Number Pct oa Magnesium aI 2.05 22 1.80 24 0.12 26 0 02s The analyses showed no difference in composition between the top and the bottom of the ingots. Spectrographic analysis of the ingots for elements other than magnesium showed, within the limits of accuracy of the method, no increase in impurities over the amounts given in the lot analysis for the high purity aluminum in Table I. Careful microscopic study of ingot 21 in the as-cast condition, at magnifications up to I 500X, revealed a cer-

Jan 1, 1949

By R. W. Raymond

In my paper on " End-Lines and Side-Lines in the Mining Law," read at the New York meeting of February, 1889 (Trans., xvii., 787), I discussed certain points involving the rights of a locator, B, who had located and surveyed a piece of ground, X + Y, of which only Y was properly subject to location, X being already held by another claimant, and had applied for and received a patent, granting X + Y, " excepting and excluding X." The paper concluded with the following questions : " Is there any difference in effect between the grant to him of Y simply and the grant of X + Y, ' excepting and excluding X' ? Why should any mining locator stake out his boundaries upon another location, and thus appear to assert a claim which he immediately withdraws? What is the legal force of such boundaries, established upon the land of another?" After calling attention to the fact that the entrance upon another's land for such a purpose is a trespass, and the principle that no trespasser can create by his trespass any right which he would not have without it, I reserved to another occasion a review of the history of the absurd practice of imaginary boundaries for mining claims, and a discussion of their legal effect. This practice is founded, of course, in the regulations and decisions of the United States General Land Office. There is nothing in the Revised Statutes which hints at it. On the contrary, the terms of Section 2322, giving to a locator " the exclusive right of possession and enjoyment" of the surface of his claim, seems clearly to forbid the use of that surface for the boundary-stakes of another locator. But the Act of 1866, though it provided for the issue of patents upon payment to the Government of so much per acre, and really by implication (as I have always believed) involved the absolute grant of the surface, was not so construed by the courts generally, or by the Land Office. Surveys were laid one over another in inextricable confusion, and the United States sold at $5 per acre the

Jan 1, 1890

By Alexander B. Morris

Studies such as the investigations into the solubility of gases in crude oil under various conditions, which have been carried on during the past three or four years, are very interesting from an academic point of view, but this consideration alone is hardly sufficient to warrant the large contributions from the industry necessary to maintain them. Some definite benefit to the industry as a whole should be forthcoming. The purpose of this paper is to direct the attention of company engineers, and company executives, to some of the ways in which the information gained from these studies can be made directly profitable. This work has two principal economic aspects. One affects the investment budget, and through it the financial requirements of the companies. The other affects operations, and through this course is reflected in current earnings. It will be shown that, as a direct result of the investigations into gas solubility, undertaken in the recent past by various investigators, it is now possible: 1. To determine more accurately the amount of reservoir oil originally present. 2. To obtain closer control on operating conditions, to effect more economical recovery. 3. To predict earlier and more dependably when and how much surface lifting equipment will be needed. 4. To reduce, or entirely avoid the very large investment in gasoline recovery equipment now frequently found necessary. 5. To control the gravity of the pipe-line oil so as to secure the greatest possible revenue from the products of the well. 6. To effect the recovery of a large amount of gasoline now wasted while the practicability of a gasoline recovery system is being decided. 7. To plan operations, by comparison with the history of old properties operated without this new information, so as to avoid the mistakes of ignorance made in the past. These points will be discussed in the following pages, though not necessarily in the order stated. There is so much overlapping of the points themselves, and of the data from which they have been drawn as conclusions, that to treat them in any particular order would require

Jan 1, 1935

By Clarence Balke

SMALL buttons of fused tantalum have been produced by are fusion in a vacuum, by drawing an arc between sticks of pressed tantalum and a tantalum-faced water-cooled copper block. However, ingots of appreci-able size can be produced only by the heat-treatment of bars pressed from powder. The following outline covering the production of finished bars of tantalum by the methods of powder metallurgy is also used for the production of columbium, taking into account the difference in the melting points of these two metals. PRESSING THE POWDER With possibly a few exceptions, a pressing operation is one of the essential steps in the practice of powder metallurgy. In fact, the author's experience with a number of high-melting-point metals and with numer-ous types of hard carbide compositions has led him to believe that this operation is often one of the most important in the- entire process, and frequently one of the most difficult to carry out in a satisfactory manner. Defects clue to improper pressing can readily lead to a defective finished product. It is the author's opinion that rarely is a bar or other article pressed from metal powder in such a way that all parts of the piece are uniformly pressed. The nearest approach to uniformity of pressing is possibly attained when the powder is contained in a flexible receptacle, such as rubber, and is pressed under a liquid by hydrostatic pressure. However, this method is not generally applicable. Hydraulic pressing in steel dies where one or two punches are forced into the die must usually be resorted to. As the pressure in such a die is built up, the powder begins to cling to the walls of the die with a tenacity dependent upon the nature of the powder, and this results in a bridging action, so that the layers of powder adjacent to the moving punch are pressed more heavily than those further removed in the mass. Frequently, as the pressure is carried higher, there may be a mass slippage of the powder upon itself, with the result that slip cracks are formed within the pressed

Jan 1, 1938

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slag. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired dements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by, any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1951

By W. H. Emmons

Most mineral deposits change as they are followed downward on their dips. Some of these changes are due to primary arrangement; different ores were precipitated at different depths when the deposits were formed. Other changes are due to weathering or secondary enrichment. The chief changes resulting from weathering, in the main, are understood and standard changes are recognized. The processes are relatively simple. They take place at ordinary temperatures and pressures and can be duplicated in the laboratories. Moreover, there are thousands of deposits available for study, because the processes take place near the surface where the development of mines is begun. The changes due to primary arrangement of the deposits of the metals are not so well understood. Deposition has taken place at higher temperatures and our knowledge of the chemistry of the processes leaves much to he desired. Very few experimental data are available. The deposits, moreover, offer fewer examples because many mines are not developed to depths where the changes can be studied and a change to unprofitable material usually results in stopping work. Most students of ore deposits now accept, as confirmed, the hypothesis that nearly all lodes and related deposits were formed by solutions originating in intrusive igneous masses. Outward from these masses, the deposits at many places are grouped in zones and the arrangement noted from the intrusions outward are commonly the reverse of the changes noted from the surface downward in a single lode. A study of the changes in groups of deposits, from the parent intrusion outward, will throw light on the changes to be expected in a single lode downward. Recause the changes in series of deposits from the intrusive outward may all be observed near the surface, where more data are available, it is possible to increase the number of examples many fold and to apply the statisttical method of study with greater confidence of avoiding error. It is not everywhere possible to identify the parent igneous body to which a group of ore deposits are related. Several kinds of criteria are available; certain groups are superior to others. By applying the

Jan 1, 1924