Search Documents

By Robert G. Johnson, Richard J. Prosen

THE present work was done in connection with a program for investigating metal-to-ceramic braze techniques using the well-known reactivity of titanium with certain ceramic oxides. The investigation extended over the range of 0 to 30 pct Ti. The indium was obtained from the Indium Corp. of America and was specified to be 99.97 pct pure. The titanium was supplied by Metals Disintegrating Co. and was stated to be 99.5 pct pure. Each 2 to 4 g quantity of the alloy compositions studied was prepared using a mixture of 300 mesh powders pressed into pellet form. The pellets were heated in thin-walled molybdenum crucibles using a resistance-wound furnace in a vacuum less than 10-4 mm of Hg. Little reaction occurred between the molten alloy and the crucibles at the temperatures and short time intervals used. Only slight spectroscopic traces of molybdenum were found in the melt after a typical period of heating. The points shown on the phase diagram of Fig. 1 represent thermal arrest measurements. The phase boundaries shown are consistent with the thermal arrest and X-ray data obtained. The temperatures were determined using a Pt-Pt 10 pct Rh thermocouple with the junction spot-welded to a short molybdenum rod. The rod was almost completely immersed in the liquid metal, so that good thermal contact with the melt was achieved. The small mass of the crucible and its contents made it possible to obtain many heating and cooling curves in a few minutes time, an advantage which helped to minimize the effects of indium evaporation at the higher temperatures. A Brown strip chart recorder was used to display the thermal arrest curves. To check the technique, the melting point of 99.999 pure Al was measured and found to be within 1 of 660.2c, the accepted melting point. The upper limit of temperature with this technique was about 900°C beyond which the evaporation rate of indium became great enough to alter appreciably the alloy composition during the runs. A peritectic transition was found at 796°+ 5°C from 1.5 to 30 wt pct Ti. It was not found at 0.5 or 1.0 pct. A small super-cooling effect was observed. The melting-point transition to the B + L phase was found up to 20 pct Ti but not at 25 pct. Within the 1 deg accuracy of the measurement, the transition temperature was that of pure indium, 156°C. The liquidus line to the left of the 1.5 titanium point was located only approximately. The two crossed circle points at 1.0 and 0.5 pct Ti place a lower limit on the liquidus line and were determined by observing visually the cessation of vibrations in the melt caused by the damping effect as B-phase crystals were formed during cooling. The B-phase boundary was found at 23.8 pct Ti by X-ray analyses of small single crystals of the B phase isolated from 2 pct Ti melts. The compound was found to be Jetragonal with lattice dimensions of c = 3.052A and a = 10.094W. From the unit cell dimensions and the measured density of 6.42 i 0.05 g per cc, the compound was determined to be In4Ti3 which has 23.8 pct Ti. The calculated density of 6.44 g per cc is obtained assuming 2 mol

Jan 1, 1962

By W. H. Blauvelt

The only way in which the difficult problems of classification of coal for the manufacture of by-product coke can be solved is to analyze them by the use of scientific data. It is very easy to adopt classifications for coal for the manufacture of by-product coke along certain lines; we can easily say that for a certain class of metallurgical operation coke made from bituminous coal must not contain more than so much sulfur or more than so much ash and should yield certain returns in the by-products, tar, ammonia, benzol, gas, etc. Those points we are fairly clear on and I think it is hardly worth while to discuss them because I presume that they are familiar to most of us who have any occasion either to make coke or to use it. But there is a field in the manufacture of coke which we know very little about. For example, we are operating a plant on a certain mixture of coal. Suddenly our blast-furnace man or the user of the coke tells us the coke is not as good as it was before. The coke is analyzed and the coal is analyzed. Everything seems to be about the same as it was— the ash is the same, there is no more sulfur, and so on—but the coke, for the use to which it is put, particularly in the blast furnace, is wrong. What happens? The management decide to try a slightly different coal mixture. They do not necessarily raise the total hydrocarbons, the volatile matter in the mixture, nor change the sulfur or the ash, but they do make a change which improves the value of the coke for metallurgical use. The reason for this difficulty, as I see it, is the " combustibility " of the coke—I hesitate to use the word, but it is the best one I have available. Combustibility of Coke We know now that the combustibility of coke is a very vital point in many metallurgical processes and I think one of the most notable instances of the proof of this is the experience of the Carnegie Steel Co. in the production of coke at its Clairton plant. The history of that

Jan 1, 1930

By Bernard MacDonald

THE writing of this paper was prompted by the discussion by H. M. Chance, in the April Bulletin, of the paper written by Thomas M. Chance which appeared in the February Bulletin., and by the remarks of the Editor in which lie stated that while the matter contained in discussion did not refer to the original paper it "was presented as of interest to the operators of cyanide and other lixiviation processes dealing with fluid mixtures of varying specific gravity." For some years past the principle enunciated in the discussion referred to has been known to the writer and demonstrated by him to be an efficient and economical way of separating water or solution from solids in the cyanidation, lixiviation or acid leaching of ore pulps: In utilizing this principle in commercial practice he has invented a method whereby not only the separation of solution from solids may be effected in any given tank, but also the counter migration of the solids and solution may be effected continuously through a series of tanks in which the hydro-metallurgical treatment of ore pulps is being carried on. In effect this method is analogous to the counter-current system, but is different physically in that it is carried on throughout a series of tanks on practically the sane level, continuously and automatically, by hydrostatic pressure and gravity-flow, without the aid of intervening pumps or elevators, at the same time that agitation is being carried on in the same tanks. In the Parral system, agitation is effected in tanks by a number of air lifts of comparatively small diameter through which the pulp is continuously transferred from the bottom of the tank and spouted horizontally on top of the charge. The spouting force of the several streams thus discharged maintains a rotary flow in the pulp charge which extends from top to bottom of the tank. This continuous transfer of pulp and the spiral flow from top to bottom of the tank maintains the pulp constituents in uniform proportions and meets the requirements of efficient treatment in a most economical manner. The quantity of. compressed air required is very small, as the pulp is not lifted but simply trans-

Jan 7, 1918

By Edward G. Norton

The salt deposits of the Mississippi Embayment region present a problem of origin so genetically related to the larger problem of the stratigraphy and structure of the region that a discussion of the one necessarily involves or assumes an understanding of the other. For this reason, I shall summarize briefly our knowledge of this region, emphasizing the facts related to the subject of this paper. In so doing I shall make liberal use of the reports of the National and State surveys. Geographically that section of the United States known as the Mississippi Embayment region represents a great V-shaped area, extending from near Cairo, Ill., to the Gulf of Mexico, and including Louisiana, eastern Texas, all that part of Arkansas bordering the Oua-chita and Ozark mountains, western Tennessee, Mississippi, and a part of Alabama. This great section Professor Harris has described as structurally a pitching trough, its medial line being well represented by the Mississippi River. Outcropping along the border of this area are the Cretaceous and Tertiary formations, unconformably laid down on the hard Paleozoic rock sheets that show more or less plication, deformation, and faulting, depending upon their proximity to the nearby major uplifts. East and west of the Mississippi River the Cretaceous and Tertiary beds dip river- and coastward at angles greater than the slope of the land. "Waters entering along the outcropping edges of the Tertiaries and Cretaceous and following bedding planes southward are soon thousands of feet beneath the surface." As the sedimentation of the region progressed, faulting and slips occurred along planes of pre-Cretaceous weakness. Whether these movements were genetically related to the loading of this V-shaped area, as Professor Harris seems to think, is a question still to be settled. The accompanying map, Fig. 1, was taken from Bulletin No. 7 of the Louisiana- Geological Survey. It shows the regional distribution of the salines, as well as an alignment of the domes, which has been assumed to indicate faulting.

Jan 1, 1915

By R. M. Genevray, M. B. Bever, E. J. Suoninen

THE martensitic transformation in the ß-phase of the Cu-Zn system has been the subject of several investigations. The transformation is known to be reversible and to be affected by stress. Its temperature range has been determined as a function of composition. In the investigation reported here, the effect of tensile stresses on the transformation was investigated quantitatively. Some information was also obtained on the thermoelastic behavior of the martensite formed in the first stages of the transformation. Most of the experiments were done with alloy E of an earlier investigation;' this alloy analyzed 60.49 pct Cu and 39.51 pet Zn by weight. The methods of shaping and heat treatment were also essentially the same as those previously used. The stress was applied to the specimen immersed in a cooling liquid. The transformation was followed by measuring the electrical resistance with a Kelvin bridge and the elongation with a cathetometer. Fig. 1 shows the M, temperature as a function of stress. Resistance and strain measurements gave essentially identical values. The results suggest a roughly linear relation between M. and in the range investigated, up to 12 kg s mm". At higher stresses, plastic deformation begins to interfere seriously with this relationship. The increase of M, with stress is consistent with published work on the effect of stress on the martensitic transformation. The slope of the curve, 4°C per kg mm ", is of the same order of magnitude as the corresponding value calculated for steel.' Fig. 1 also shows the difference, AM, between the temperature of 50 pct transformation on cooling, as measured by changes in length, and that of 50 pct reverse transformation on heating. This difference, which may be considered a measure of the hysteresis, increases with stress; the decrease at highest stresses is probably associated with plastic deformation. Preliminary work using only resistance measurements was done with an alloy containing 60.15 pct Cu and 39.79 pct Zn by weight. The results indicated higher values o-F M, in agreement with the known variation of M. with composition.' The effect of stress on M, (2°C per kg mm-') was of the same order of magnitude as that shown in Fig. 1 for composition E. An increase in hysteresis with stress was also found. The following experiment was made in order to investigate a partially transformed structure. A specimen of alloy E was cooled to — 85°C under a stress of 4.7 kg mm-'. Under these conditions, the martensitic transformation started but did not go to completion. The stress was then released and the specimen cooled to — 105°C. Fig. 2 shows the measured elongation c. The first change in the slope of the curve indicates the beginning of the transformation under stress. Removing the load at —85°C caused a decrease in length to the value corresponding to the elastic elongation of the parent phase resulting from the applied stress. Hence, the marten-site formed in the first part of the experiment apparently disappears completely and without hysteresis upon the release of the stress. The increase in length on further cooling indicates renewed formation of martensite. These conclusions are consistent with the concept of "thermoelastic" martensite," which has been confirmed by test." Acknowledgments The authors are greatly indebted to Professor M. Cohen for his advice and encouragement. They also thank F. Paxton for assistance. Thanks are due the American Brass Co. which supplied the alloys. References E. Kaminsky and G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1936) 6, p. 984. A. B. Greninger and V. G. Mooradian: Trans. AIME (1938) 128, p. 337. "J. E. Reynolds, Jr. and M. B. Bever: Trans. AIME (1952) 194, p. 1065; Journal of Metals (October 1952). 'A. L. Titchener and M. B. Bever: Trai~s. AIME (1954) 200, p. 303; Journal of Metals (February 1954). " 3. A. Kulin, M. Cohen, and B. L. Averbach: Trans. AIME (1952) 194. p. 661; Journal of Metals (June 1952). "J. K. Pate1 and M. Cohen: Acta Metallurgica (1953) 1, p. 531. 'C. Crussard: Comptes Rendus (1953) 237, p. 1709. ' G. V. Kurdjumov: Zhur. Tekhn. Fiziki SSSR (1948) 18, p. 999. G. V. Kurdjumov and L. G. Khandros: Dokl Akad. Nouk. SSSR (1949) 66. p. 211.

Jan 1, 1957

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.1 It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anorthosite, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagioclase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout' Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a. zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized! The bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15º. The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1952

By Pablo Hadzeriga

Great Salt Lake brine was subjected, in laboratory scale, to conditions simulating solar evaporation. Solid phases and the variation in composition of the liquid phase throughout the potassium salts crystallization zone are presented. These experimental results are discussed and compare with stable equilibrium data of the quinary system Cl-, SO4, Na+, K+, Mg + + and H2O. The Great Salt Lake brine in Utah is a vast reserve of several potential chemicals which has attracted much attention in the recent past. From the standpoint of an ore reserve, it may be said that the lake contains a low grade ore which has to be concentrated by evaporation of water. Because of the fairly favorable weather conditions in the Great Salt Lake area, it seems reasonable to consider solar evaporation as an economical means of concentration. From the view of phase chemistry, the main constituents of Great Salt Lake brine make it belong to the five component system: C1-, SO4=, Na+, K+, Mg++ and H2O. Because of their low concentration, the presence of other elements may be regarded as having little effect on the equilibrium of the five main components. Equilibrium data for the quinary system of our interest has been available for many years. Using these data, it is possible to calculate how the brine of the lake will concentrate when subjected to solar evaporation. In practicing solar evaporation, the weather factor and supersaturation conditions cannot be ignored, but their introduction into calculations using equilibrium diagrams is almost an impossible task. With the experimental work presented in this paper, an attempt is made to compare the stable equilibrium data of the quinary system as applied to the case of the Great Salt Lake brine and the dynamic equilibrium when that brine is subjected to continuous solar evaporation. Sea water brine belongs to this quinary system when only the major constituents are considered. The study of this system has been carried on since the last decades of the nineteenth century. The reason for these intensive studies was to give a geological explanation to the underground potash deposits. AS a result, many theories were presented trying to relate the equilibrium data with the geological formation, paragenesis and metamorphism of these deposits. Two main approaches were followed for the equilibrium studies of this quinary system. One of them, and the best known to us, was the school started in Germany in the last century by J. H. Van't Hoff. The other one, which started about the same time, was the school of N. S. Kurnakov in Russia. Both approaches were different and as a consequence generated opposite theories about the geological formation of potash deposits. The Van't Hoff school studied the quinary system of sea water under careful laboratory control, resulting in stable phase diagrams. During these studies, Van't Hoff recognized the difficulties in crystallizing some double salts.' ". . . . we unexpectedly found that some compounds whose formation in the solutions under investigation was possible at 25°C, nevertheless totally failed to put in an appearance. These, not to mention the calcium salts, were leonite, MgSO4 . K2SO4 4 H2O; kainite, KC1-MgSO4 . 3 H2O; and kieserite, MgSO4 .H2O. Even exceedingly slow crystallization with the addition of the compounds themselves did not remove the condition of supersaturation in the case of these bodies." However, those salts (leonite, kainite, and kieserite) were included in the stable phase diagram at 25°C as shown in Fig. 1 using D'Ans data.3 The figure also shows the sequence of crystallization of the Great Salt Lake brine according to the stable diagram. In later studies by the Van't Hoff school, especially by D'Ans,3 Karsten,4 Autenrieth,5,6 attention

Jan 1, 1968

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By Richard Henry Lee

Since the economies in the blast furnace resulting from enriching iron ores are so great, much attention has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods of agglomeration and sintering, of more or less value, have been put into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the gubstance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the ides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 1, 1914

By Harold Rabling

The following notes are taken from results obtained on a standard 25-ft. Hancock jig1 tested during regular operation in the Bonne Terre mill of the St. Joseph Lead Co. The object of the tests was to determine the conditions for most effective work, and the nature of products that could be made. The material treated was sized between 9-mm. and 2-mm. round-hole screens, and was constant throughout the experiments. Three products were made, concentrates from the first three hutches, middlings from the fourth and fifth, and tailing from the sixth. The middlings were crushed in one pair of Allis-Chalmers Style B, 30 by 14-in. rolls, and elevated with the original ore to the 2-mm. screens, oversize of which formed the jig feed. While this arrangement was very simple, it gave rise to undesirable crowding of the circuit. Table 1 shows tonnage and assay values of the jig feed and products at the beginning of the experiments, and brings out the excessively large amount of middlings, comprising 63.3 per cent. of the total material fed to the jig. The rolls, being heavily overloaded, did very little crushing, a screen analysis of the product showing that only 27 per cent., or 128 tons, was crushed fine enough to pass to the tables. The remaining 347 tons returned to the jig with 400 tons of original ore. At .times, this overcrowding became much worse, and the tonnage in circuit grew to enormous proportions. It became imperative

Jan 1, 1918

By Edna A. Dancy, Ronald L. Pastorek, Gerhard J. Derge

In an earlier study1 in this laboratory, it was found that there is a minimum in the specific conductance of Ni-S melts in the region of the stoichiometric composition, Ni3S2. This and similar observations on other sulfide1 and telluride2 systems suggest that short-range order exists in the molten phase for several hundred degrees above the melting point, and a qualitative energy-band model has been proposed, with intrinsic semiconduction at the stoichiometric composition and degenerate electron and hole conduction at metal- and tellurium-rich compositions. This suggestion has been substantiated for the telluride systems by Seebeck coefficient measurements which showed a change in sign from negative on the metal-rich side to positive on the tellurium-rich side. In the present investigation, in order to substantiate still further the proposed model, Seebeck coefficient determinations have been extended to the Ni-S system over a composition range in the vicinity of Ni3S2. The experimental method was essentially the same as that used for the telluride systems, with minor modifications on cells for high sulfur melts to permit the use of tungsten wires and W— W-Re th~rmocouples instead of the chrome1 or alumel wires and chromel-alumel thermocouples originally used. Chrome1 and alumel both deteriorate very rapidly in atmospheres containing sulfur. The Ni-S alloys were prepared as described in the conductivity paper. Initially, a portion of the solidified melt was analyzed at the end of a run, but after this was found to be inaccurate because of segregation during cooling, the whole sample was analyzed. The nickel content, only, was determined, the sulfur content being obtained by difference. The results are summarized graphically in Fig. 1, and clearly show a change in the sign of the Seebeck coefficient in the region of the stoichiometric composition. This change of sign near Ni3S2, coupled with the minimum in the conductivity, is suggestive of an intrinsic semiconductor at the stoichiometric composition, with degenerate electron and hole conduction on either side of this composition, in keeping with the proposed model. The negative temperature coefficient of conductivity, normally indicative of metallic conduction, is not inconsistent with this model. In the completely degenerate region it would be expected, while in the vicinity of Ni3S2 the suggestion originally made by Argyriades, Derge, and pound3 for the Fe-S system can probably be applied. They proposed that the forbidden gap between the valence band and the conduction band is small, and that the increase in the number of the conducting species with increase in temperature is not large enough to compensate for the loss of mobility through thermal scattering. The research was sponsored by the Office of Naval Research under Contract NONR-760(22) Project NR 039-081. 'E. A. Dancy and G. J. Derge: Trans. Met. Soc. Aime, 1963, vol. 227, pp. 1034-38. 'E. A. Dancy: Trans. Vet. soc. AIME. 1964, vol. 233, pp. 270-77. 'D. Argyriades, G. Derge, and G. M. Pound: Trans. Met. Soc. . 1959, vol. 215, pp. 909-12.

Jan 1, 1965

By Alexandre Mitinsky

The theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,l that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably due to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually assumed, though incorrectly, that the proportional limit is determined by the ultimate strength. In Germany the poin't at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining the elastic limit by alternately loading and unloading the test specimen is a lengthy process and time has in itself a very considerable influence on the results of physical tests.

Jan 1, 1916

By AIME

ENGINEERS have long pondered the answer to the question of "How am I doing?" and in large measure the answer from the economics angle is provided by the 1946 survey of the engineering profession now being published by the Engineers Joint Council as an eighty-page bulletin entitled "The Engineering Profession in Transition." The survey, based upon a completely precoded mail questionnaire, aimed at three major objectives: (1) to determine the general impact of World War II upon the profession in the period 1939 through 1946; (2) to obtain re- R liable data from which valid findings could be derived to predict how active the profession would be after 1946; and (3) to determine if the war's upheaval had changed materially the pattern of professional activities, education, background, and earnings from those which existed prior to 1939. Abundant data on the economic status of the engineer based upon years of experience in his particular field, the specific branch of the industry in which he served, and his educational background are presented. Relationships between years of experience

Jan 1, 1947

By Stuart McGill

This case-study of the financing of the Ok Tedi project illustrates the nature of project financing and outlines the arrangements made in the case of this project; it also demonstrates that the limitation of financial exposure is an important goal for Governments involved in developing the resources sector. The account includes a chronological description of the process by which the sponsors prepared for the financing of the project and the lenders became involved in it. The type of security arid loan documentation required for such financing is described, together with a broad analysis of their content and the manner in which the various risks involved in development are apportioned among the sponsors and lenders. The ability to apportion and limit financial liability is an important development for the owners of capital and resources.

Jan 1, 1985

By FREDERICK C. BROWN

THE practice of fine-grinding is now being so successfully - carried on in some fields, notably in West Australia, and its advisability has been so frequently pointed out' that the matter in this paper is not put forward as being new ; its chief object being to call attention to the importance of fine-grinding in the treatment of comparatively low-grade ores. I have been engaged during the last five years in the cyanide-treatment of ores in the Ohinemuri district (North Island), New Zealand, and I consider that, in the near future, extremely fine-grinding (almost sliming) will become a very important feature of the milling-methods in this field, since it seems absolutely necessary to reduce the most of ores to a very fine state of division if a high extraction is to be obtained; and, in most cases, the extra percentage of saving will leave a good margin above the increased cost of treatment due both to the fine-grinding and to the interest on the capital spent for the grinding-machinery. The average ore of the Ohinemuri field is composed of a quartz-gangue with some calcite, carrying the gold-value in the form of an alloy of gold and silver in about equal proportions, and the silver-value in the form of mixed sulphides of silver, usually associated with a considerable amount of iron pyrites. In the upper levels, the ores are decomposed and carry large quantities of black manganese oxide and some iron oxide, but, as. depth is reached, the decomposed ore gives place to sulphides and, in some mines, rhodonite, manganese silicate, is present in fairly large quantities. The average value of the

Jan 1, 1906

By Hermann Bach, Walther Hänig, Willi Gehrhardt, Ernst Theurich, Walter Langner

With the construction of the Magdeburg zinc works, the Georg von Giesche's Erben Mining Co. of Breslau has to a certain extent completed the program of reconstruction which it set as its goal after the boundaries of Upper Silesia were drawn by the Treaty of Versailles. During its history, covering.more than two centuries, zinc and lead mining has been its chief activity. Through the new boundaries established, it lost to Poland all its mines and smelters, including five distillation smelters. Of its extensive properties, there remained only an apparently unimportant and unexplored portion of the old Bleischarley ore field which, however, happily made possible the resumption of its old business. In 1925 the Deutsch-Bleischarley shaft-only a few kilometers from the old Bleischarley shaft—was sunk and developed, and in May 1926 production of lead and zinc ore was resumed. As facilities for smelting were lacking, the ore was at first delivered to the neighboring smelters, which had now become Polish. Realization of the plan to build its own zinc works had to be postponed at first for lack of capital. In the meantime, however, plans for the new works were worked out in all details. After extensive experimentation in a semicommercial pilot plant it was decided, at the end of 1928 and the beginning of 1929, to use the electrolytic process and, for economic reasons, to place the works at Magdeburg. With zinc at the approximate price level that had ruled since the Deutsch-Bleischarley mine had begun working, it was hoped that the plan could be completed in 1930 with the company's own resources. However, falling metal prices, already noticeable in 1929, made this impossible, and further postponement for a time became necessary. Finally, at the end of July 1933, the funds for building the works became available, in the form of a loan granted under the first employment

Jan 1, 1937

By Alfred E. Hunt

The application of the color-method for the estimation of manganese in iron and steel, based upon the depth of the characteristic purple color of permanganic acid, was first made in this country, the writer thinks, by one of the members of the American Institute of Mining Engineers, Mr. Samuel Peters, in 1874, at the laboratory of the Bay State Iron Company, and was published by him in the Chemical News. The method is credited to him in the new edition of Crooke's Select Methods. The principle of oxidizing manganese with peroxide of lead, or other oxidizing agents, and determining the amount of manganese from the color of the purple permanganic

Jan 1, 1887

By D. R. Uhlmann, T. P. Seward, O. Chalmers

A magnetic field has been used to damp out liquid convection during the solidification of castings. Ingots of Al-2 pct Cu were poured from various sperheats (10" to 65°C) into a room-temperature graphite mold located between the poles of an electromagnet. The effect on ingot structure of varying the strength and time of application of the magnetic field was investigated, and the results are interpreted in light 01- current theories of ingot structure. In the solidification of alloy systems, thermal gradients in the melt and differences in density of the constituents are expected to produce convective motion in the liquid. The thermal convection caused by temperature gradients should be present during the freezing of both alloys and pure materials, while the solute convection caused by density differences should be of concern only for alloys. The possible influence of this natural convection on the structure of castings has been discussed by Ruddle,' Chalmers, and Tiller. More recently, an experimental investigation of such effects was carried out by Cole and Bolling. These workers took stationary molds containing lead- and tin-based alloys and. using a brine solution. quenched them from various superheats above their respective liquidus temperatures. When grids were placed across the mold diameter to suppress convection, the grid region was later observed to contain a larger percentage of columnar grains than other parts of the casting or than similar castings poured without the grids present. From thermocouple measurements, they found the temperature in the grid region to be higher than that in the region outside the grids throughout the freezing process, and concluded that convection should be an important mode of heat transfer in normal castings. In addition to such convection arising from thermal gradients or differences in density of the constituents, a further source of convective motion, which we shall call "momentum convection", may be particularly important in small (laboratory-size) castings. By this term we refer to the convective motion produced in the initial pouring process, a motion which is damped out as the linear momentum and angular momentum of the liquid are dissipated. Besides these sources of convection, which are present to some extent in all castings. external influences may also be effective in producing convective motion. Examples of such "forced" convection which have been discussed in the literature include stirring the melt, shaking the mold, rotating the mold, and so forth The purpose of the present study was to examine the effect of convection on the structure of castings poured into a cold mold. In this work, a magnetic field was employed to damp out the convective motions within the liquid, and hence control the extent of con- The effect of a magnetic field on convective currents in a conducting liquid is to induce eddy currents which oppose and damp out the convective motion. vection. The technique of magnetic damping was previously used by Utech and F1emings" in their study of convective effects on impurity banding and other substructure in alloy crystals grown unidirectionally from the melt. In their investigation, fields as small as 200 gauss were found to be effective in damping the convection currents which influence the banding. I) EXPERIMENTAL TECHNIQUE In the present study, alloys of A1-2 wt pct Cu were poured into a room-temperature graphite mold. The mold, in the shape of a circular cylinder, 2 in. ID, 2-3/4 in. OD, 5 in. inside height, and 5-1/2 in. outside

Jan 1, 1967

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

By Francis Foley

FROM the point of view of the metallographist, the adaptation of x-rays to the study of the crystal structure of metals is of the greatest importance. While one may hardly consider the findings resulting from x-ray study as revolutionary, their positive nature, compared with the deductions we have been forced to accept from the work that had gone before, gives firmer ground on which to build and furnishes new fields for speculation. Prior to the advent of the crystallogram, the best work on the crystal structure of steel was that of Osmond and Cartaud.1 They concluded, from their investigation with percussion figures formed at various temperatures, that alpha, beta, and gamma irons belonged to the cubic system and that they showed well-marked specific characteristics and could not have the same internal structure. What the internal structures were, they had no direct method of determining; but from a consideration. of the fact that the 001 plane (that parallel to the cube face) is a plane of perfect cleavage and minimum hardness in alpha iron and that the 111 (octahedral) plane is by far the most important in the crystallography of gamma iron, they were led to suggest the simple cubic arrangement as that of alpha and the face-centered cubic arrangement as that of gamma iron. They suggested the body-centered cubic arrangement as that of beta iron. The atomic arrangement of the various crystal forms of iron has been quite definitely determined in recent years by means of x-rays and the work of Westgren2 and Westgren and Phragmèn3 has been rather conclusive. They not only determined the atomic arrangement of alpha, beta, and gamma iron but also that of the high-temperature modification delta.

Jan 10, 1925