Search Documents

By S. R. Goodman, Hsun Hu

The rolling texture transition in copper as a function of deformation temperature is found to be quite similar to that in high-purity silver. The ordinary copper type texture changes gradually to the brass type, accompanied by an increase in the stacking fault frequency, as the temperature of deformation decreases. The rolling textures obtained at low temperatures and the corresponding annealing textures compare remarkably well with the ordinary rolling and annealing textures of low-zinc brasses. Furthermore, it is also found that the observed stacking fault energies of copper specimens deformed at low temperatures correspond closely with those of low-zinc brasses, as deduced from measurements of the dislocation nodes. These results are consistent with the idea that texture transition may be significantly dependent on the stacking fault energy. It was shown in a series of previous publications1"3 that the rolling texture of high-purity silver changes gradually from the common silver type (or the brass type) to the copper type* with increasing temperature *The silver or brass type rolling textures are commonly described as (110)[112],4,5 whereas the copper type rolling textures are mainly (123) [a121 and (146)[211].5 Other ideal orientations have been used by various investigators for the copper type rolling textures, but the actual difference among these ideal orientations is rather small. of deformation, and that such texture transition can be correlated with the change in stacking fault frequency as a function of rolling temperature. Furthermore, it was shown that the formation of annealing textures in high-purity silver from the various rolling textures obtained during the course of texture transition depends entirely upon the deformation texture. From a common silver type or brass type rolling texture (such as produced by rolling at 0" or at 50° C) the recrystallization texture is mainly (120)[211], which is quite different from the recrystallization texture of brass.* However, for both ma- terials the orientation relationship between the rolling texture and the recrystallization texture can be expressed in terms of similar rotations around [Ill.] axes of approximately 30 or 35 deg. They differ in that the [Ill] rotational axes are different. In the case of high-purity silver, the axes of rotation are the two (111) poles near the plane normal of the deformed specimen with a (11l)[112] type rolling texture, whereas in brass, they are the (111) poles near the direction of rolling. For high-purity silver with a predominantly copper type rolling texture (such as produced by rolling at 150° or 200°C) the recrystallization texture is mainly (100)[001], or the cube texture, plus its twin orientations. It was shown previously6 that such reorientation observed in copper or aluminum can be described as [Ill] rotations of 30 to 40 deg. For intermediate cases, i.e., when the rolling textures are composed of a

Jan 1, 1963

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

By T. Glen Heslop, Dennis H. Laubscher

INTRODUCTION In all cave mining operations waste is drawn mixed in the ore, hauled, hoisted and milled. This waste usually contains some mineral which partly covers some of the costs of mining and milling it, but it still re- presents a loss of profits as the production rate from the mine is matched to the mill capacity - every tonne of waste milled replaces a tonne of profitable ore. Draw control aims to reduce the amount of waste drawn and to increase the amount of ore recovered. It is also used to regulate the grade of ore flowing to the mill and in block cave blocks to prevent potential stress build- up on the major apexes above grizzly drifts. This paper summarises what has been learnt about draw control in the forty years that cave mining methods have been used in the three largest underground chrysotile asbestos mines in the southern hemisphere. The four mining methods to which draw control has been applied are: a. Block caving. b. Shrinkage with overburden caving. c. Sublevel caving. d. Open stoping. Open stoping has been included because on a number of occasions severe falls from the back and side of these open stopes have occurred. Without full records of where and when ore is blasted, when and how much ore has been drawn from each of the drawpoints, it would be impossible to analyse the migration of ore and fallen waste in the stope. Several problems peculiar to chrysotile asbestos ore bodies affect the practice of draw control. Heterogeneous fragmentation, cavities, side pressures and the interaction of stresses in the caved ore affect the migration of ore under draw. Fibre is normally not developed uniformly throughout the ore bodies, values vary from place to place but there is usually a general decrease upwards and the hangingwall contact is an economic limit. The immediate hangingwall rock frequently looks like the ore body hostrock and is difficult to recognise in a drawpoint, and cannot be used as the marker for stopping draw. During caving or shrinkage, a large proportion of fibre becomes detached from the host rock and re- ports in the fines, which migrate differently to the larger rocks. The fines are not sticky, and flow easily if loose and dry, but compacted, the fibre and rock fines con- solidate the ore. During draw the proportion of fines in the ore varies considerably, as fines either flow relatively freely between the large rocks or become trapped and compacted above large rocks or hangups. This creates a large sampling error in drawpoint grade assessments, whether done visually or by bulk sampling, unless the assessments are done frequently. The method of draw control used is to regulate the draw rate in an attempt to lower the ore-waste interface as evenly as possible, and to finally stop working the drawpoint when a calculated tonnage has been drawn.

Jan 1, 1981

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By W. O. Philbrook, H. W. Hosking, N. B. Melcher

Rates and patterns of gas flow in an experimental blast furnace were investigated by measurements, at three levels, of gas compo-sitions and temperatures and by direct determination of gas transit time by a new method employing mercury vapor as a tracer. Infer-ences were drawn about localized reaction zones and the mechanism of the onset of' channeling. LACK of precise knowledge of the nature of gas movement in the blast furnace has always been an impediment to better understanding of the blastfurnace process as a whole. The effects upon operation of various types of charge distribution are very largely brought about by the modifications to gas flow which they occasion. Intelligent evaluation of these effects demands a better understanding of the factors influencing gas flow and the ways in which the flow pattern is altered by conditions existing in the stock column. The same knowledge is required before a fundamental approach can be made to the problem of establishing optimum lines for new furnaces. An experimental furnace is operated at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Advantage was taken of experimental operation to conduct an investigation to develop and evaluate methods of study which could be applied later to industrial furnaces. The gas composition and temperature determinations were made as a preliminary study so far as gas flow was concerned but yielded significant information relating to other processes occurring within the furnace. The direct measurement of gas transit times by the mercury-vapor method constituted the major object of the investigation. Development of the mercury-vapor method was carried out while the data on gas composition and temperature were being collected. A complete description of the principle and development of the mercury-vapor method is beyond the scope of this paper but is available elsewhere. The results obtained and some consideration of the method's effectiveness and its potential value in the study of industrial problems will be treated here. DESCRIPTION OF FURNACE The general lines of the experimental blast furnace are shown in Fig. 1. The hearth diameter was 3 ft at the beginning of the investigation, and this was later enlarged to 3 ft 9 in. and finally to 4 ft to increase capacity. Tuyere to stockline height is 21 ft 4 in. The bosh depth is 3 ft 4 in. over which it opens to a width of 5 ft, and this diameter is carried up for 2 ft in a cylindrical section. The inwall batter of 1/2 in. per ft. is considerably less than in larger installations This may have influenced the movement of gaseous and solid materials. The furnace is inside a laboratory building and is charged from outside by a skip and hoist. Feeding into the first of three bell chambers, the stock is distributed by rotating the upper bell, the other two being used to obtain an effective gas seal. Three water-cooled tuyeres, with a nozzle dia-

Jan 1, 1960

By Gerald Edmunds

Castings of pure metals and many alloys usually have a coarse-grained structure characterized by long columnar grains throughout the main body of the casting. Frequently, the surface exhibits finer, sometimes nearly equiaxed grains, and such grains may also compose other parts of the casting. This paper deals .primarily with determinations of the grain-orientation textures of the columnar and surface grains of polycrystalline zinc castings. It includes some results upon a cadmium casting and a magnesium casting. A hypothesis is developed to account for the observations on columnar grains and to use as a basis for predicting orientations in other cast metals. A general description of the position of the columnar grains in castings is that their long axes are approximately parallel to the direction of the thermal gradient during crystallization. Thus, in cylindrical castings the columnar grain axes tend to be radial, and in large flat castings where most of the cooling is through one or both of the large mold surfaces they tend to be perpendicular to the mold surfaces. At the edges and corners the direction of heat flow and therefore the position of the grains is more cornplex. Actually observation shows that even in castings made in flat molds the cooling seems to be somewhat irregular, since columnar grains tend to emanate from certain areas of the cooling surface, indicating that thermal contact was better there than in neighboring areas. The nucleus from which a columnar grain grows may be so oriented that its direction of maximum growth rate does not coincide with the direction of the thermal gradient. In this case the long axis of the grain probably assumes an intermediate position. Notwithstanding these minor irregularities, the situation does exist that the long axes of the columnar grains are generally disposed approximately perpendicular to the mold surface. Schmid and Wassermanl and Nix and Schmid2 have determined the orientation texture of columnar grains in castings of several cubic, tetragonal, hexagonal close-packed and rhombohedra1 metals. For zinc and cadmium, they report the basal plane to be parallel to the columnar grain axes, with no preference for any particular direction in this plane to coincide with the grain axes. This texture, termed a ring fiber texture,3 is uncommon in metals; zinc and cadmium are the only ones reported to exhibit it. Generally, it is stated, a simpler texture exists in which a principal, though not necessarily the most closely packed, crystallographic direction is parallel to the direction of heat flow. In cast magnesium (also hexagonal close packed) they report a digonal axis I, [100] direction, parallel to the direction of heat flow. The writer is not aware of any other orientation-texture determinations on cast polycrystalline hexagonal metals. In view of the observations reported in the present paper it is of interest also to note that Nix and Schmid stated that a

Jan 1, 1941

By Earl Ingerson

BORE surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. METHOD AND APPARATUS In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel ,bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. st the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 5000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (1:16), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1947

By FRANK RIEBERS

IN DISCUSSING the selection of a geophysical method, much of what the writer will say is applicable to any of the various methods and to their use in prospecting, whether for oil or for other minerals. Specifically, the writer's subject is the problem, particularly pressing on the Pacific Coast, of checking the rising cost of the discovery of new fields by the proper employment of geophysical methods. Table I was prepared from statistics published by the California State Milling Bureau. The writer selected five of the largest a:ld most active companies operating in California, segregated the number of wild-

Jan 1, 1930

By E. B. BESSELIEVRE

THE great work of Gorgas in stamping out yellow fever in Panama during the construction of the Canal was one of the chief factors contributing to the ultimate accomplishment of the task, two previous attempts having failed largely through the demoralization of workers by epidemics of contagious diseases. Mining camps, rapidly constructed during the boom days of the rushes to new fields, have been frequent sufferers from typhoid when, as so often used to be the case, little or no attention was given to bacterial examination of the water supply or to the method used for disposing of the sewage.

Jan 1, 1930

By J. H. Swisher

When an Fe-Mn alloy is internally oxidized, the inclusions formed are MnO which contains some dissolzled FeO. In the internal oxidation reaction, not all of the manganese is oxidized; some remains in solid solution as a result of the high Mn-0 solubility product in iron. Taking these factors into consideration, the rate of internal oxidation of an Fe-1.0 pct Mn alloy is computed as a function of temperature, using available thermodynanzic data and recently published data for the solubility and diffusivity of oxygen in iron. The predicted and experimentally determined rates for the temperature range from 950 to 1350°C are in good agreement. ThE rates of internal oxidation of austenitic Fe-A1 and Fe-Si alloys have been studied extensively.1"4 Schenck et al. report the results of a few experiments with Fe-Mn alloys at 854" and 956C, and Bradford5 has studied the rate of internal oxidation of commercial alloys containing manganese in the temperature range from 677" to 899°C. When Fe-Mn alloys are internally oxidized, the inclusions formed are solutions of FeO in MnO, the composition depending on the experimental conditions. Since the thermodynamics of the Fe-Mn and FeO-MnO systems have been investigated,6"9 and since the solubility and diffusion coefficient of oxygen in y iron have been determined recently,' it is possible to predict the rate of internal oxidation from known data. The calculations used in predicting the rate of internal oxidation will first be outlined, then the results of the prediction will be compared with the experimental results of this investigation. PREDICTION OF PERMEABILITY FROM THERMODYNAMIC AND DIFFUSIVITY DATA Oxygen is provided for internal oxidation in these experiments by the dissociation of water vapor on the surface of the alloy. The dissociation reaction is: + H2(g) + [O] [1] where [0] denotes oxygen in solution. The equilibrium constant for this reaction is known as a function of temperature:' log As oxygen diffuses into the alloy, oxide inclusions are formed which are MnO with some FeO in solid solution. The reactions occurring are: [Mn] + [0] = (MnO) [31 and [Fe] + [0] = (FeO) [41 where [ Mn] is manganese dissolved in iron and (FeO) is iron oxide dissolved in MnO. The overall reactions may be written as follows: [Mn] + HOte) = (MnO) + H2(£) [5] and [Fe] + H20(g) = (FeO) + Hz(R) [61 The standard free-energy changes and equilibrium constants for Reactions [5] and [6] are known.6 Therefore the equilibrium constants for Reactions [3] and [4] may be obtained by combining known thermodynamic data for Reactions [I], [5], and [6]. For Reactions [3] and [4]: K = and For the present purpose, both the Fe-Mn7,8 and FeO-~n0' systems can be considered to be ideal, i.e., [amn] = [NM~] and (aFeO) = (NM~~) = 1 - (NFeO) where the Ns are mole fractions. These relations, together with Eqs. [I] and [8], permit us to compute both the oxide and metal compositions as a function of temperature and oxygen potential at any point in the specimen. For cases where the oxygen concentration gradient between the surface and the subscale-base metal interface is linear, the kinetics of internal oxidation is an application of Fick's first law: where dn/dt is the instantaneous flux of oxygen into the specimen, g-atom per sq cm sec; 6 is the instantaneous thickness of the subscale, cm; Do is the diffusion coefficient of oxygen in iron, sq cm per sec; p is density of iron, g per cu cm; h[%O] is the oxygen concentration difference between the surface and sub-scale-base metal interface, wt pct. B6hm and ~ahlweit" derived an exact solution to the diffusion equation for systems in which there is a stoichiometric oxide formed. They showed that the oxygen concentration gradient is given by a rather complex error function relation. For the Fe-Mn-0 system and for most other systems that have been studied, however, variations in oxide compositions are small and rates of internal oxidation are sufficiently slow that the deviation from linearity in the concentration gradient of oxygen is negligible. The mass of oxygen transported across a unit area of the specimen for the total time of the experiment is given by the mass balance equation:

Jan 1, 1969

By R. T. Hukki

This paper presents a series of equations for mechanical ball wear, relating parameters of ball size, mill speed, and mill diameter. The fundamental equation, Eq. 12, presented here is introduced to correlate these basic parameters and thus define and clarify the concept of ball wear. This equation is offered as a general rule, which may be modified to apply to individual problems of grinding. BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that 1 n = 0.7663 np----=— rpm [1] vD P = c, np D kw [2] T=c²(np)n De tph [3] In these equations n — actual mill speed, rpm np = calculated percentage critical speed D = ID of mill in feet P = power required to operate a mill, kw T = capacity of a mill, tph C¹ and c² - appropriate constants in = exponent of numerical value of 1 5 m 1.5 Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate). It is generally accepted, although not sharply defined, that ball wear in mills running at low (cascading) speeds is a function of the ball surface available. Accordingly, the wear of a single ball may be considered to be a homogeneous, linear function of its surface and of the distance traveled. Thus dw = f¹(d2) . f2(ds) [4] where dw is the wear of a single ball in time dt, d the diameter of the average ball in ball charge, and ds the distance traveled by the ball in time dt. Indicating that ds - a D n dt, the wear of the average ball in time dt becomes dw = f¹(d2) . f2(Dn dt) 1 --- f¹ (d1) f² (D c3 np-----— dt) \/D = c,d² n, D dt The rate of wear of the average ball is given by dw/dt. dw/dt = c, d² np D lb per hr [5] The weight of the ball charge per unit of mill length is a function of D The number of balls of size d in the ball charge is = f³(D2)/f4(d³). The rate of wear of the total ball charge equals the number of balls times rate of wear of the average ball. Thus rate of total ball wear = — . (dw/dt) w. c, . (l/d) . n,, D lb per hr [6] which is the equation of ball wear in low speed mills. In a mill running at a low speed, grinding is the result of rubbing action within the ball mass and between the ball mass and mill liners. When the speed of the mill is gradually increased toward the critical, the impacting effect of freely falling balls becomes increasingly prominent in comparison with the rubbing action. Reduction of ore takes place partly by rubbing, partly by impact. The share of the freely falling balls in the reduction of ore reaches its practical maximum at a speed somewhat less than the critical; at that speed grinding by rubbing has decreased to a low value. It may be reasonable to think that size reduction by freely falling balls should reach its theoretical maximum at the critical speed, if the fall of the balls were not hindered by the shell of the mill beyond the top point; grinding by rubbing would cease at the critical speed. As a first approximation, wear of freely falling balls may be considered to be a homogeneous, linear function of the force at which they strike pieces of rock and other balls at the toe of the ball charge. The force equals mass times acceleration. The mass of a ball is a function of d3 and its acceleration is a function of the peripheral speed of the mill. The wear of a single ball of size d representing the average ball in a ball charge will therefore be w¹ = f3(F) = f (d3) f7 (v). [7] Indicating that v = D n, and n = c³ np 1/vD, Eq. 7 becomes W1 = cn d3 np Do.5 lb per hr. [8] Total wear of the ball charge equals number of balls times the wear of the average ball. Number of

Jan 1, 1955

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

By G. M. Willis, F. L. Hennessy

The oxygen pressure in equilibrium with silver and Ag2O-B2O3 melts has been measured between 800&apos; and 900°C, to obtain the thermodynamic properties of the liquid. The compound Ag20. 4B20:1 appears to exist in the liquid, which shows marked heat content and entropy effects. A KNOWLEDGE of the thermodynamic properties of binary liquid silicates, borates, and phosphates would be of considerable assistance in the interpretation of the behavior of multi-component metallurgical slags. However, the literature contains comparatively few studies of the thermodynamics of binary slags. The system Ag20-B,O, attracted our attention as it was known to give a single liquid phase,&apos;,&apos; in which high contents of silver could be obtained (up to 61 pct Ag according to Foex2). Further, it would be expected that the partial pressure of oxygen over melts in equilibrium with metallic silver could be used to determine the activity of Ag2O in the Ag,O-B,O, system. In many respects, it may be expected that the reaction of a basic oxide with boric oxide would be analogous to its reaction with silica. Liquid immiscibility frequently occurs in both borate and silicate systems. With B2O3 and SiO reaction with a basic oxide presumably involves a breakdown of the three-dimensional network of the acid oxide by reaction with oxygen atoms common to more than one silicon or boron atom. Ag2O-B2O3 was therefore investigated as a model of a slag system in the hope that its thermodynamic properties would assist in understanding those of other systems. Several methods for determining the activity of a component in a slag have been described in the literature. Chang and Derge" used high temperature electromotive force measurements to obtain the activity of SiO2 in CaO-SiO2 and Ca0-Al203-Si02 slags, but the cell reaction in their work is not clear. low has used rate of volatilization and vapor pressure measurements combined with phase diagrams to obtain activities in the systems KO-SiO,, Na,O-SiO, and Li,O-SiO," and PbO-SiO26 Taylor and Chipman7 extrapolated their results for the distribution of FeO between liquid iron and CaO (+Mg0)-FeO-SiOl slags to obtain the activity of FeO in the binary FeO-SiO2 system. In principle, one of the most direct methods for obtaining the activity of a metallic oxide in a phase is by comparison of the equilibrium oxygen pressure for the system metal-pure oxide with that of metal oxide-containing phase. Schenck and othersa have studied the stabilization of Ag2O on combination with other oxides (MO,) in the solid state by measurements of the oxygen pressure in systems of the type Ag-Ag,O-xM0,-MOy-0, (gas). Schuhmann and Ensio" have determined the activity of FeO in iron silicate slags in equilibrium with solid iron, using CO/CO2 mixtures to establish known partial pressure of oxygen. Although the method gives the activity of FeO without ambiguity, the slag is not a binary system, and interpretation of the results in terms of the hypothetical binary system FeO-SiO, is not possible. If a metal is solid at temperatures at which the properties of the slag containing its oxide are to be studied, this method has the considerable experimental advantage that the metal can be used as the container for the slag, and contamination by contact with refractories is avoided. In this work, crucibles for Ag2-B,O, melts were made from silver, and the liquid brought to equilibrium with definite pressures of oxygen gas. The oxygen pressure PO, thus fixes the activity of Ag20 in the liquid silver borate. For the reaction at a given temperature. is substantially constant, is directly proportional to the square root of the equilibrium oxygen pressure. Varying the oxygen pressure changed the silver oxide content of the liquid and it was possible to obtain the activity of Ag2O over a range of composition. Experimental Procedure In principle, the method consisted of bringing melts in silver crucibles or boats to equilibrium at a fixed temperature under a definite pressure of oxygen and analyzing the glass after solidification. Materials: B2O3 glass was prepared from A.R. quality boric acid by fusion in platinum. The silver

Jan 1, 1954

By T. E. Watkins, M. D. Nelson

INTRODUCTION Deeper drilling for oil is becoming more and more the rule rather than the exception. With deeper drilling come additional problems, perhaps the greatest being those brought on by the higher temperatures encountered down the hole. particularly in the Gulf Coast region of Texas and Louisiana. Temperature gradients of the order of 1.8° to 2.0°F/100 ft are not unusual, and a gradient of 2.3"F.&apos;100 ft is found in some areas of Texas. With a mean surface temperature of 74oF, the following temperatures could be expected for a geothermal gradient of 2.0°F; 100 ft: at 10,000 it. 271°F. 12,000 ft, 314°F: 14,000 ft, 354,oF; and 16.000 ft. 394°F. Severe gelation of lime-base drilling fluid in wells that have high bottom hole temperatures has become perhaps the most serious difficulty enconntered in drilling under such conditions. Lime-base drilling fluids have been very succesefully and widely used in the drilling of wells in the Gulf Coast region because of their inherent stability toward contaminants. their ability to suppress the swelling dispersion of bentonitic shales, and their ease of maintainance. The gradual recognition: during the past few years, that these muds were. in themselve. the cause of many difficulties experienced in drilling has led to wide-pread efforts by the drilling industry. to determine the reasons for the failure of these mud systems and to develop mud systems capable of performing satisfactorily under high-temperature conditios. MANIFESTATIONS OF HIGH-TEMPERATURE GELATION it is generally possible to recognize the symptons of high-temperature gelation early enough that advance predictions can be made of serious difficulties. in mud control, and the useful life of the drilling fluids can be extended by proper treatment. Following i.; a list of the manifestations of high-temperature gelation: (1) The drill string &apos;takes weight&apos; while going in the hole after a trip. In early stages of high-temperature gelation it is possible to notice a slight reduction in drill string weight as the drill pipe is lowred near the bottom of the hole. (2) Excessive pump pressure is required to .tart the circulation of drilling fluid at or near the bottom of the hole when going hack to bottom after a trip. As the severity of the gelation increases it may be necessary to break circulation a number of times when going in the hole. (3) The drilling fluid from the bottom of the hole is thick and often granular or lumpy when pumped up after making a round trip. In a severely gelled drilling fluid system such a condition may be irreversible; that is, it cannot be stirred or chemically treated to produce a satisfactory drilling fluid. (4) Completion tool.. such as logging tools or perforating guns will not sink to the bottom of the hole. On some occasions completion tools will become stuck and require a fishing job to retrieve them if the wire line attached to them is broken. It is often difficult to determine whether the condition of the drilling fluid is responsible for sticking the tool or whether the wire line becomes key seated in a crooked hole and causes the allow difficulty. When there are 110 other symptoms of high-temperature gelation. then the difficulty may usually be attributed to the latter cause. (5) In extreme cases of high-temperature gelation it is necessary to "wash" and "ream" when going back to bottom after coming out of the hole. (6) In many -instance. it has been found to be extremely difficult and expensive to 1111 production packers 2nd tubing in moderately deep oil wells which had been drilled with a lime-base drilling fluid. In such instances-the original mud had apparently "set" to a consistency approaching that of a weak cement. CAUSES OF HIGH-TEMPERATURE GELATION Extensive test; have indicated that a lime-base mud does not develop a highly gelled condition at temperatures below 250°F. whereas above that temperature such condition often develops rapidly. (Fig. 1) concurrently. the following changes are evident ill the mud: (1) The alkalinity of the mud decreases to a very low value. with both caustic soda and lime being consumed. (2) The quartz content of the mud decreases sharply. (3) The bentonitic content of the mud decreases or di-appears, with concurrent decrease or loss of base exchange capacity of mud solids. (4) New compounds formed in the mud have been found to be cal-cium silicate, calcium aluminum silicate, and calcium sodium aluminum silicate. (5) The mud loses the ability to form a filter cake of low permeability. The above characteristics have been discussed, in part. by other authors

Jan 1, 1953

By R. W. Balluffi, R. Resnick

NUMEROUS investigations of chemical diffusion in a brass have been made and the results are collected in several places.1-3 This work has been mainly concerned with the determination of the chemical diffusivity as a function of composition and temperature. In 1947 Smigelskas and Kirken-dall&apos; showed that zinc and copper diffuse at different rates in face-centered-cubic brass, and since then, a number of efforts have been made to determine the intrinsic diffusivities of zinc and copper in this alloy.1, 5-9 Horne and Mehl8 in particular have recently determined the intrinsic diffusivities as functions of temperature and composition using sandwich-type couples and inert markers. Inman et al." also have determined the intrinsic diffusivities in homogeneous alloys using tracer techniques. When the present work was started, no information of this type was available. Consequently, measurements of the intrinsic diffusivities were made as a function of temperature at a constant composition of 28 atomic pct Zn with vapor-solid diffusion couples where the zinc was diffused into the diffusion couple from the vapor phase. The application of these couples to the study of diffusion in a: brass has been described previously.0,7 The temperature dependence of the intrinsic diffusivities was found to follow the relation D, = A, exp(-Hi/RT) and the values of Hzn, and Hcu, were found to be closely the same. It is emphasized, however, that the chemical dif-fusivity (D = N1D2 + N2D1) is a composite diffusivity and does not necessarily follow this exponential form. It is usually found to do so within experimental error for substitutional alloys because the heats of activation of the intrinsic diffusivities generally are not greatly different.&apos;" Also, at the onset of this work, there was no information available concerning possible unequal diffusion rates of individual components and the existence of a Kirkendall effect in alloys with other than face-centered-cubic structures. Since then, two reports indicating a Kirkendall effect in body-centered-cubic ß brass have appeared. Landergren and Mehl" have published a note describing Kirkendall diffusion experiments with sandwich-type couples. Inman et a1.9 also find a Kirkendall effect in this alloy using the tracer technique. In the present work, several aspects of the Kirkendall effect in ß brass were further investigated using vapor-solid couples. Two different couples were used, one in which the zinc was diffused into the specimen from the vapor phase and the other in which the zinc was diffused out of the specimen into the vapor phase. Briefly, the existence of a Kirkendall effect is confirmed and it is found that Dzn/Dcu = 3 at about the 46 atomic pct composition in this alloy at 600°, 700°, and 800°C. As a result of the unequal diffusion rates of zinc and copper, volume changes occur and subgrain formation is observed in the diffusion zone. In addition, significant porosity is produced by the precipitation of supersaturated vacancies. Diffusion in this alloy is therefore outwardly similar to diffusion in a brass where these effects are also observed, a Brass Experimental Methods—The use of vapor-solid couples in studying diffusion in a brass has been described in previous articles.6,7 The method briefly consists of sealing a copper specimen with Kirkendall markers initially placed on its surface in an evacuated quartz capsule along with a large zinc source of fine a brass chips and then diffusing the zinc into the specimen through the vapor phase. The zinc concentration at the specimen surface rises rapidly enough to a value near that of the a brass source so that the surface concentration may be regarded as constant during diffusion. Under these boundary conditions, values of the chemical diffu-sivity may be obtained by applying the Boltzmann-Matano analysis to the concentration penetration curve, and the intrinsic diffusivities may be obtained from Darken&apos;s5 equations when the velocity of marker movement is known. The diffusion specimens were made from OFHC copper in the form of disks 3.2 cm diam and 0.5 cm thick with faces surface-ground parallel to within +0.001 cm. Markers in the form of fine alumina particles <0.0002 cm diam were placed on the specimen surface. These specimens were then sealed in quartz capsules along with enough a brass chips of a 30.0 atomic pct Zn composition to keep the source concentration from decreasing by more than 0.3 atomic pct Zn as a result of the loss of zinc to the specimen during diffusion. The quartz capsules which were initially evacuated to a pressure of

Jan 1, 1956

By J. S. Levine, M. Prats

A homogeneous and uniform cylindrical reservoir containing oil and gas is fractured vertically on completion and is produced at a constant bottom-hole pressure. The fracture has an infinite flow capacity, is of limited lateral extent and is bounded above and below by the impermeable strata defining the vertical extent of the reservoir. Results show that such a fractured reservoir can be represented by a reservoir of circular symmetry having very nearly the same production history. The well radius of this circular reservoir is about 1/4 the fracture length and is essentially the same as that obtained previously for a single fluid of constant compressibility. At the same value of cumulative oil production, gas-oil ratios of fractured reservoirs producing at constant terzinal pressure are larger than those of reservoirs having no fractures. This leads to more inefficient use of the reservoir energy in fractured wells and results in lower reservoir pressures for the same cumulative oil production. The reduction in operating life due to fracturing a reservoir is not as great as that for a slightly compressible fluid. This diflerence can be accounted for by the lower reservoir pressure in the fractured reservoir and its adverse effect on the average mobility and compressibility of the oil. As anticipated, the reduction in operating life increases czs the reservoir permeability decreases. The type of results presented in this report can be used to determine the economic attractiveness of fracture treatments per se, to setect the initial spacing to be used in developing a field, and to compare the relative merits of fracturing available wells and infill drilling. INTRODUCTION The effect of vertical fractures on a reservoir producing either an incompressible or a compressible liquid has already been discussed in the 1iterature.l,2 Those results indicate that the production history of such a reservoir is essentially the same as that of a circular reservoir having an effective well radius of approximately one-fourth the fracture length. The present work reports on the effect of a vertical fracture on a reservoir producing two compressible fluids —oil and gas—by solution gas drive. Because of the empirical nature of the PVT and relative permeability data used to obtain the performance of such reservoirs, results can only be obtained numerically and with the aid of high-speed computers. Since reservoirs lose their radial symmetry when fractured vertically, pressure and saturation can no longer be given only in terms of distance from the well. Two coordinates (such as x and y) must now be used to describe the pressure and saturation within the reservoir, and, since we are dealing with compressible fluids, time is also a variable. Thus the solution of a vertically fractured reservoir requires finding two unknowns (pressure and saturation) in two space variables (say x and y) and in time (t). Since no means are readily and generally available for solving such problems at the present time, we have used the results of previous work1,2 to approximate the effect of a vertical fracture on a reservoir producing both oil and gas by depletion. The purpose of the present wmk, then, is to investigate the possibility of using available numerical techniques (limited at the moment to one space variable) to study the two-space-variable flow behavior resulting from a vertical fracture. Results obtained in the course of this investigation are also reported and discussed. Input and output data of the numerical methods used are given in practical units: BOPD, feet, psi, cp, and md. Results are discussed fist in terms of specific reservoir and crude properties and geometries. Later, dimensionless parameters are introduced in order to extend results to different values of some of the reservoir and fracture properties. IDEALIZATION AND DESCRIPTION OF THE FRACTURED SYSTEM It is assumed that a horizontal oil-producing layer of constant thickness and of uniform porosity and permeability is bounded above and below by impermeable strata. The reservoir has an impermeable, circular, cylindrical outer boundary of radius r,. The fracture system is represented by a single, plane, vertical fracture of limited radial extent, bounded by the impermeable matrix above and below&apos; the producing layer (reservoir). It is assumed that there is no pressure drop in the fracture due to fluid flow. 1 indicates the general three-dimensional geometry of the fractured reservoir. Gravity effects and the effects of differential depletion resulting from variations in hydrostatic head (pressure) will be neglected. Thus, the flow behavior in the fractured reservoir is described by the

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By G. Baralis, P. Gondi, I. Tangerini, G. Scandola

The precipitation behavior of Zn-0.5 pct A1 alloy single crystals was studied by means of electrical resistivity measurements and by optical and electron microscopy. The single crystals for the resistivity measurements were prepared by an original method in - 100-p -thick sheets. The order of the precipitation kinetics ranged between 1 and 1.5. The dislocations play a relevant role in the first-order kinetics. Precipitation always occurs both on dispersed particles and on dislocations. Statistical examinations have shown that the first-order kinetics can have two different activation energies; i.e., the precipitation can have dz;fferent mechanisnrs which could not be identified, however, in the course of the research. During the tnetallographic exanzination of the precipitation structures a specific process of dislocation decoration was obsereed. The main purpose of this work was to study the contribution of dislocations to the precipitation. A number of authors have observed precipitation on dislocations and reference might be made to several monographs on the ubject.&apos;&apos; The possibility that dislocations also accelerate precipitation has been considered by Turn-bull3 and Fischer et al.4 The studies described in the present paper were carried out on zinc, chosen as a base metal owing to the ease with which dislocations can be introduced into it and because of the absence of excess vacancies after quenching in conditions where phenomena of accelerated precipitation still occur. Aluminum was preferred as alloying element because of the accelerated precipitation phenomena that resulted in a preliminary reearch. EXPERIMENTAL METHODS The observations refer to a Zn-0.5 pct A1 alloy. The zinc was 99.995 pct pure; a typical spectroscopical analysis is given in Table I. As a rule the alloy was subjected to homogenization, quenching, or slow cooling and annealing. Homogenization was carried out by heating at 390" to 410°C for 24 hr. From the homogenization temperature, some specimens were quenched and some slowly cooled at a rate of 2°C per sec. At this rate no precipitate was detectable under the optical microscope just after cooling. Quenching was carried out simply by dropping the specimens into water, aqueous ethylene glycol solution at -30" c, or liquid-nitrogen baths placed close to the homogenization oven. Vaseline oil baths were used with a thermal stabilization of 10-20 for both the aging treatments and the measurements; aging was generally carried out at 90" or 130°C. To avoid oxidation phenomena during heating, the vaseline oil baths had to be frequently renewed. The precipitation kinetics were studied by means of electrical resistivity measurements, using ans potentiometric method (reproducibility ± 5 x 10 5 v, that is 0.5 pct of the total voltage decreases on the specimens during precipitation). First, various types of specimens were tested, i.e., polycrystals, single crystals grown in capillary quartz tubes, and thin single-crystal sheets prepared by means of an original method requiring no container except for the natural oxide. Even if fully annealed, the polycrystals and the capillary grown single crystals showed resistivity in -creases, most probably due to dislocations introduced in the course of the measurements. Similar resistivity increases in pure zinc were noticed by another author. Only the single-crystal sheets showed no resistivity change; thus they were chosen for the subsequent tests. As already mentioned, these single crystals were obtained by using, as a container, the natural oxide on the zinc surface; the oxide strength is sufficient to maintain the original shape during melting with sheets up to 500 p thick. An initial zone melting and subsequent zone leveling, which led also to formation of the single crystals, were thus carried out on rolled sheets of the required thicknesses (- 100 p) and shape, lying on a flat silica surface. The resistivities were first evaluated by measurements at the liquid-nitrogen temperature. This method gave poor reproducibility, however, and this was attributed to the thermal cycles which had to be operated. To avoid cycles and handling, it was therefore decided to make measurements directly in the annealing oil baths; this required thermal stabilization at ilo-&apos; "C. In this way only the resistance changes were measured. Specimens of pure zinc and of completely annealed alloy were always examined as controls together with those under consideration; only those measurement runs were taken into account where the reference samples showed no resistance increases. Again, the main inconvenience was due to oxidation and this was avoided by renewing the oil baths; even so data reproducibility was poor and the observations were therefore carried out on a large number (many hundreds) of specimens so as to provide indications of statistical value. For the transmission observations under the elec-

Jan 1, 1969