Search Documents

By F. Weinberg

In developing a mechanism for the solidification of metals from the melt, it has been proposed that solidification proceeds by the growth of platelets parallel to close packed planes. The evidence for this is based primarily on observations of decanted interfaces of lead1,2 and tin on which platelets 1 to 10 µ thick4 were observed. In recent observations of decanted eutectic alloys, 5,6 it was found that the eutectic structure on the decanted surface was markedly different than that of the bulk material, with the surface structure extending approximately 10 µ behind the interface.' This suggested that, at least for these experiments, a residual liquid layer 10 µ thick had been left on the decanted interface, which solidified subsequent to decanting. If a similar thickness of residual liquid was left on the decanted surfaces in the lead and tin observations referred to above, then it is questionable to what extent the observed platelets can be related to the solid-liquid interface before decanting. The purpose of the present investigation was to measure the thickness of the residual liquid layer on a decanted surface of tin, using relatively standard decanting procedures. The technique used was to add approximately 200 ppm of Tl204 (PI) to the melted portion of a high purity (99.999 pet) bar of tin, which was being progressively melted from one end, and then decant during melting. Since only the melt contained the radioactive tracer, the activity emanating from the decanted surface could be used as a measure of the thickness of the residual liquid layer. Progressive melting was carried out in the same fashion as single crystal growth, namely, in a horizontal graphite boat, in an argon atmosphere, using a moving furnace. The decanting was done in two ways; 1) removing the furnace and suddenly dropping the melt end of the boat, and 2) suddenly jerking the solid away from the liquid by the action of a falling weight (estimated peak acceleration 3 x 105 cm per sq sec), using a split graphite container. In all cases the melt was vigorously agitated by bubbling argon through it. The activity of the decanted surface was measured through an aperture 1.5 cm by 0.5 cm in a lead shield with an Anton tube geiger counter. Assuming that the active layer on the surface had the same concentration of Tl204 as the decanted liquid, the thickness of the layer could be determined from the measured activity of the decanted material, and the relationship between activity and material thickness. The latter was determined by rolling some of the decanted material into foil and measuring the activity of multiple layers of the foil. The activity At of material of thickness t (in mm) was determined to be A, = Ao(1 - e-22.5t) where Ao is the activity of the bulk material. The results of the measurements of the thickness of the residual liquid layer for six decants are given in Table I. The variation in t is attributed to variations in the decanting procedure and the rate of melting, the latter being difficult to control because of the vigorous agitation of the liquid. The rate of melting was in the order of 2 cm per hr, estimated from the position of the solid-liquid interface during melting. The results indicate that a residual liquid layer of the order of 10 µ in thickness is left on the decanted interface in agreement with the observation on eutectic alloys referred to above. If the mixing of the liquid during melting is not complete, as was

Jan 1, 1962

By W. Allen

FOR the past six years gravity surveys have been used for underground prospecting in the copper mines at Bisbee, Ariz. The primary purpose of the surveys has been to reduce the diamond drilling and crosscutting necessary for exploration. Since many of the orebodies are small, and geologic control is not always apparent, any information that will direct the drilling and crosscutting is highly desirable. Because of extensive development and exploration work in the copper mines at Bisbee, it has been possible to cover more than 630,000 ft of crosscuts on 30 levels with the gravity surveys. In the process the gravity procedures have been refined to a high degree. Density Contrast: For a gravity survey to be successful, a sufficient density contrast must exist between the geologic feature sought and surrounding host rocks. Most mineralized areas will provide this contrast if fairly massive bodies are present. In the Bisbee area the entire sequence of formations, except for alluvium, appears to have specific gravities ranging from 2.65 to 2.70. These values have been determined by means of a large number of cut samples and diamond drill cores. As a further check, vertical gravity differences have been used where nonmineralized sections are known to occur.' The only known major gravity disturbances result from mineralization that has increased the density and the voids that have decreased density. The voids are caused by mining operations and by underground water movement that has developed several areas of caverns. Equipment: While not absolutely essential, a small rugged gravity meter, such as the Worden meter, is highly desirable. A tall tripod, about the height of a transit tripod, permits instrument set-ups in deep water and in locations where fallen timber and muck piles make it impossible to use a short tripod. An additional advantage of a tall tripod is that it places the meter in the center of the crosscut, reducing the error caused by the crosscut void. Size and weight are important, since the only satisfactory means of operating the meter underground is to carry it by hand. A backpack can be used in rare instances but is usually a hindrance because of the close station spacing. The operator's ability to move through tight clearances will improve survey coverage, as it is then possible to move through raises and caved areas and to pass mine cars and machinery with a minimum of trouble. Station Control: Gravity stations are normally located every 100 ft along the crosscuts, at each intersection, and in the face of all stub crosscuts. In areas of high gravity relief, or where small anomalies might be expected, stations may be located at 25 or 50-ft intervals. When possible, the stations should be offset to avoid effects of raises or other voids. The gravity stations on a level are tied to one or more base stations, which are usually located at the shaft or near the portal of an adit. The base stations may be part of a gravity control net that extends to each level in the mine as well as to the surface. Such a net extending throughout the potential area of the surveys is highly desirable, as it is then possible to compare all gravity stations on a uniform basis. The stations that are part of the base net should be carefully established by multiple readings and, if necessary, by a least squares adjustment of the loops. In some instances where levels do not have a shaft station, or where access may be blocked by caving, it may be necessary to establish secondary bases at the top and bottom of the raises that are between levels. Under fair conditions 70 to 90 gravity stations can be located and run in 6 hr by a two-man crew. The best field procedures depend on conditions. Reduction of Field Data: Most of the time required to produce a final gravity map is consumed in processing the data. Each meter reading must be corrected for a minimum of five factors that affect the gravity value in addition to the density contrast being sought. These factors are 1) instrumental drift, 2) station elevation, 3) topography, 4) latitude, and 5) regional gravity gradient. Mine openings, such as stopes and raises, will affect the value. However, it is seldom practical to make corrections for these voids. Usually a rotation is made on the field note on the station, and any

Jan 1, 1957

By Milton E. Wadsworth, T. D. Chatwin

Bulk density variations can usually be minimized by properly mixing the material before moisture measurement. The measuring of moisture on material being with- drawn directly from storage bins requires some form of bulk density correction. In Bethlehem's pellet plants continuous automatic bulk density correction and uniform feed-rate control are obtained with Bethlehem's patented Bin Level Control System. With this sys- tem a single probe, suspended or inserted in the bin, senses whether material is at the proper level in the bin and automatically regulates filter speed to control the filter-cake discharge rate to maintain this level. The level of concentrate in the filter-cake bin can thereby be controlled to within ± 1/2 in. of the point of contact between the concentrate and the probe. Material thickness on the conveyor does not have to be controlled accurately and mix compositions can vary widely as long as they do not contain variable amounts of water-soluble electrolytes. In sinter plants, errors caused by changes in normal feed rate and bed height are minimized by counter-weights that permit the free-floating to maintain a uniform contact pressure on the mix. Large changes in mix resistance can be taken care of either by resetting the control point or by adjusting the calibration control.

Jan 9, 1968

By W. Gundaker, F. C. Schwerer

Natural chromium-bearing spinels (chromites), which are used as refractory materials in basic steelmaking, are the only commercially important chromium ore and are also encountered as difficult-to-separate contaminants in ore deposits of potential economic value. Techniques for characterization and separation of ore materials frequently are dependent on the magnetic properties of the constituent minerals. An experimental program was initiated to explore the effects of temperature and of simple mechanical and thermal treatments on the static magnetic properties of several ore-grade natural chromites. Studies of the temperature dependence of the magnetic properties showed that the natural chromites, which are dilute in the magnetic ions Fe and Cr, order magnetically only at cryogenic temperatures. However, mechanical treatment in the form of crushing produces a magnetic component that is ordered at room temperature and that is of sufficient strength to alter magnetic-separation characteristics. The additional magnetic component apparently is associated with surface structures which develop during crushing and disappear after heating to above about 500°C. Preliminary studies indicate that this surface structure enhances the susceptibility of the chromite grain surfaces to gas reactions at moderate temperatures.

Jan 1, 1976

By G. W. Nabor, H. J. Ramey

A blotter-type electrolytic model was utilized to prepare flow diagrams for a field test of the in-situ combustion process. It is pointed out that the areal sweep of a combustion pattern is similar to sweep patterns that would be developed at an infinite mobility ratio, which exists (approximately) across a combustion front because of the complete removal of liquids from the sand behind it. The precision of the blotter method was tested by comparison with results obtained by other techniques and was found to be satisfactory. The blotter-type model will not furnish as much information as more elaborate and expensive potentiometric models, but its speed of operation and ease of construction make it a highly satisfactory tool to determine areal sweep patterns. A tabulation of sweep efficiency and mobility ratio is furnished for various well geometries. INTRODUCTION In connection with the first field experiment with the in-situ combustion method of oil recovery," flow diagrams for the unique well geometry and boundary conditions involved in the subject test were developed. From these diagrams, information concerning the areal sweep and distribution of flow was obtained. A survev of the literature on potentiometric models, utilized to solve two-dimensional flow problems,1,2,3,4,5,6,8,9,10 indicated that the information desired could be obtained by means of a blotter-type model by making certain modifications in the technique. The following discussion describes the application of the modified blotter-type electrolytic model to the solution of the problem of the flow of gases in an oil reservoir for an engineering appraisal of the progress of the combustion front during the first field experiment. Considerable information has been published on the theoretical aspects of electrical model techniques. One author stated that:' "The models are based on the observation that since the velocity of an ion in an electrolytic system is proportional to the potential gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the paths of the ions in the electrolytic systems must be similar to those of the fluid particles in a porous medium with the same geometry and equivalent boundary conditions." This suggestion of a real analogy has been established repeatedly by comparisons of analytic derivations with model results. The analogy between the movement of a combustion front and the model results is not as apparent, since the combustion process differs from water flooding and gas cycling in that the velocity of the burning front is different from the velocity of the injected fluid at the front in combustion. Analogy between electric current flow and movement of the burning front exists because the local velocity of the burning front is proportional to the air (mass) velocity at this point (assuming frontal temperatures are at least as high as the ignition temperature of the fuel). Most model studies fall into one of two categories: (1) electron conduction, or (2) ionic conduction models. Examples of these are models which employ as flow media either a thin metal sheet, or a porous blotter saturated with an electrolyte, respectively. Of the two, the porous blotter model, an ionic conduction model, appears to be the most adaptable to the flow problem that results when using in-situ combustion. This problem requires that the mobility of the particles in the model be controlled analogous to the mobility of gas flowing through burned sand of high permeability to gas and then through oil sand of lower permeability to gas. Although the blotter model has heretofore been

Jan 1, 1955

By Robert H. Richards

VERY little has been published recently on this subject in the mining journals or proceedings of societies. The attention of experts has been diverted perhaps by the demands for pan amalgamation of refractory ores. Yet free milling ores occur in many localities, and it may be interesting to have on record some data as to details of running a small test-mill, especially as details of results do not seem to be accessible to students and investigators. Küstel, in 1863, under battery amalgamation, dismisses the subject by stating that "amalgamation on copper-plated platforms, troughs, and other copper fixings" is " very imperfect, and mostly abandoned." J. Arthur Phillips says, in 1867, under placer mining : A well-amalgamated copper plate is considered as effective for

Jan 1, 1880

By R. F. Sheldon

Largest uranium deposit in the Northwest is Dawn Mining Co.'s Midnite mine on the Spokane Indian B Reservation. The orebodies lie along the contact of granite and metamorphosed sedimentary rock and are controlled by faults and shear zones near the granite contact. In the oxidized zone the deposits consist mainly of the secondary uranium mineral meta-autunite; sooty uraninite and primary uranium minerals are known to occur at greater depths. Elevations in the mine area range from 2500 to 3500 ft. The rolling hills and low, rounded mountains are covered with grass and evergreen trees.

Jan 5, 1959

By J. T. Raleigh, D. L. Flock

This study investigated the nature of formation plugging with bacteria and attempted to relate its characteristics to physical rock properties. Fifteen core samples of four specific formation types were defined and plugged using a commonly occurring, uniform sized dead bacteria, Bacillus subtilis. Two of the formation types were fairly uniform-grained sandstones and two were heterogeneous carbonates. The injection rate and concentration of solids in the brine were held constant during the test runs. The pore geometry factor G was a significant petro-physical rock characteristic for correlation with depth of plugging, but lacked importance as a parameter for rate of plugging. Although the G factor may not completely describe porous rock geometry for plugging predictions, for reservoirs with multi-pore systems, there is evidence that the pore geometry factor might form a basis for establishing injection water specification in more llornogeneous reservoirs with only primary porosity development. INTRODUCTION GENERAL PURPOSE Injecting water into oil-bearing formations to increase recovery is common practice in the petroleum industry. One of the most serious operational problems involved with water injection wells is the tendency of the porous rock immediately adjacent to the injection wellbore to plug partially. This results in increased injection pressures and/or a decrease in the rate of injection. This plugging in injection wells can result from a number of causes, including bacteria contained in the injected water.1 The purpose of this work was to investigate the nature of injection plugging with bacteria and to attempt to relate its characteristics to physical rock properties. Many variables exist in research of this type, so, to reduce them, injection rate and concentration of bacteria in brine were held constant. The bacteria used for plugging was a uniform-sized, dead bacteria, Bacillus subtilis, a micro-organism commonly found in water, air and soils. Four specific porous rock types were plugged—two consolidated sandstones and two heterogeneous carbonates. The experimental work involved two distinct phases. The first concerned determining the physical rock properties and the second was the experimental work of actually plugging the selected core samples. PORE GEOMETRY FACTOR Capillary pressure is necessary to displace a wetting fluid from a capillary opening with a nonwetting fluid. The factors which govern capillary pressure are the surface or interfacial tension of the fluids involved, the system wettability and the equivalent pore radius. Thus: P,= 2ucososrd..........(1) Thomeer used the idea that the location and shape of the capillary pressure curve reflect characteristics of the pore structure of any porous media sample.' He presented the mathematical description of capillary pressure curves and of indicated differences in pore geometry of samples. where G = pore geometry factor PC = capillary pressure Pi = displacement pressure (V,)p, = fractional bulk volume occupied by the displacing fluid at any capillary pressure (V,), = fractional bulk volume occupied by the displacing fluid at infinite pressure or total interconnected pore volumes. The shape of the curve is defined by the pore geometry factor G. The curve shape is related directly to the sorting and interconnection of the pores of the sample. The location of an infinite number of curves can be defined by the same asymptotes. However, these curves differ in shape, each curve being described by a specific value of G. Thus, the description of a curve is unique when, in addition to the position of its asymptotes, its shape is defined. These curves can be used graphically to determine the characteristic parameters of any arbitrarily located curve. Those parameters that can be approximated from any capillary pressure curve are: (1) total interconnected pore volume, represented by (V,),- ; (2) extrapolated displacement pressure, the abscissa axis; and (3) pore geometry factor, by the curve shape. PROPERTIES OF BRINE AND BACTERIA The fluid used throughout this study was an aqueous solution of sodium chloride, 25,000 ppm by weight. The addition of salt to fresh water was intended to eliminate clay swelling in the sandstone cores and to retard leaching in the limestone cores. The viscosity of the brine solution at 100F, the temp-

Jan 1, 1966

R. E. Powers (Mellon Institute of lndustrial Research, University of Pittsburgh, Pittsburgh)—Several of the processing methods at the Josephtown smelter might well be considered by plants producing iron blast furnace sinter. In making blast furnace sinter the objectives are much the same as at Josephtown: To produce a strong yet porous agglomerate which has a size consist in a preferred range. The emphasis however is on production rate rather than on the size or other quality characteristics of the sinter. Therefore the technique is entirely different. Blast furnace sinter plants attempt to make their product in one pass with a minimum recirculating load and without sizing treatment after the sinter leaves the machines. Many plants are beginning to feel that more attention paid to quality characteristics would make the product a more desirable blast furnace material. The pelletizing of very fine material before placing it on the bed is not deliberately done at iron sinter plants, although the installed equipment sometimes gives a simila; action. Such pelletizing seems to be a promising way of accommodating the down-draft sintering Drocess to very fine materials. he recirculating load at Josephtown is extremely high. Two plants' producing blast furnace sinter from raw material of comparable size have a recirculating load of about 100 pct of production. At Josephtown it is notable that the size and the rate of feeding of return fines are under control. This is not the case in most blast furnace sinter plants. The sinter slicer appears to be a worthwhile aid in effecting such control. It is similar in action to rakes and plows used at a number of plants, but it has the advantage that the sinter dislodged is positively removed and not left to the inefficient action of a stationary grizzly screen. Blast furnace size specifications for sinter are not at present so rigid as the Josephtown specifications. If the sizing of blast furnace sinter does become important, then the Josephtown crushing practice, in which a large recirculating load is maintained on the crusher in order that minimum fines be produced, may be of interest. H. K. Najarian (authors' reply)—We note that Mr. Powers appreciates some points that we tried to emphasize in our paper as being of importance in making zinc sinter of good quality and which may well be applied to iron blast furnace sinter. Fig. 2 shows the pelletized nature of the feed going on to a Dwight-Lloyd type sintering machine in our plant. Practically, the entire feed consists of more ,or less rounded particles which permit more uniform air passage through the charge, while the larger particles in the charge roll on to the surface of the grate, which helps to keep the grate openings from being clogged by excessive fines. An agglomerated charge of this character may preferably be made by rolling action while being mixed in a rotating drum and wetted by water sprays to bind the fine particles together and give the charge the desired moisture content. From our observations of several iron ore and blast furnace flue dust sintering operations, we believe that if the fines from the sinter discharged from the machines were to be recirculated and agqlomerated with the new feed, not only sinter of better quality but larger capacity from the machines may be realized.

Jan 1, 1952

B. S. Crocker (Screened Ore Used for Fine Grinding at Lake Shore Mines, P. 499) was born in Toronto, Ont. and attended Saint Andrews College and University of Toronto. He received a B.A. and M.A. degree. He was graduated with honors and received a fellowship in metallurgy. Mr. Crocker did post-graduate research at University of Toronto from 1933 to 1934. He was employed by Beattie Gold Mines in 1933. He did research in milling at Lake Shore Mines from 1934 to 1936 and from 1936 to 1940 was head of experiment laboratory. At the present time he is mill superintendent with Lake Shore Mines at Kirkland Lake, Ont., Canada. Grinding, cyanidation, flotation and roasting are of special interest to him. He is a member of AIME. Mr. Crocker has presented several papers before C.I.M.M. and also holds membership in this society as well as Professional Engineers of Ontario. Skiing, yacht racing and photography are his favorite hobbies.

Jan 1, 1952

By L. D. Anderson

WHEN, after years of troublous experiences in roasting sulfide ores with heavy dust and fume losses resulting from the equipment and methods first available, there appeared on the scene of metallurgy that revolutionary process known as sintering, it was felt that at last there had been found the ideal method for preparing sulfide ores for blastfurnace reduction. Not only were the sulfides roasted but also the fine oxidized ores were bound together with them in strong porous cellular masses which were in the best possible condition for reduction. With the experiences gained in the manipulation of the Huntington-Heberlein, Carmichael-Bradford, and Dwight & Lloyd processes there developed a refinement of detail which brought the whole plan of roasting by sintering to a high plane of perfection. But that metallurgy is never stationary is revealed by the fact that changes in milling practice, particularly the development of flotation, have introduced a new set of problems in sintering itself. Inasmuch as it is felt that these problems have not yet been solved in an entirely satisfactory manner this paper is written to record the present practice of the Salt Lake Valley smelters with the hope that there will be brought forth such discussios as may perhaps lead to still better practice. By far the greater proportion of the sulfides smelted today are flotation concentrates. Usually they are high grade, sometimes as high as 70 per cent. and more in lead. They are extremely fine, many mills grinding the ore so that from 60 to 80 per cent. will pass through screens of 200 mesh. The physical condition in which many of these concentrates reach the smelters is disconcerting to the metallurgists. Some are of about the consistency of putty. Others are of a sticky, slimy nature. Others again, dried to the limit, are veritable powders. Remembering that the down-draft sintering charge for the best results must be porous enough to let air be drawn through it reasonably well, must be thoroughly mixed, and must have some coarse material in it to segregate out and form a layer on the grates, it will be understood that the advent of this extremely fine material has made necessary still further elaboration in the equipment and processes of preparing sulfides for the blast furnaces,

Jan 1, 1929

By William B Price, Ralph W. Bailey

Arsenic, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in condenser tubes. This subject has been thoroughly covered by Barry,l who de- scribed the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume-Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 lists them as 'rhobomhedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By Ralph W. Bailey, William B. Price

Arsenic, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in condenser tubes. This subject has been thoroughly covered by Barry,l who de- scribed the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume-Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 lists them as 'rhobomhedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By Ralph W. Bailey, William B. Price

INTRODUCTION ARSENIC, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in [ ] condenser tubes. This subject has been thoroughly covered by Barry,1 who described the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 [ ] lists them as "rhombohedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By Ralph W. Bailey, William B. Price

ARSENIC, antimony and phosphorus are now used in the brass industry as standard inhibitors in preventing dezincification in [ ] condenser tubes. This subject has been thoroughly covered by Barry,1 who described the testing procedure by total immersion of suitable specimens in a I per cent cupric chloride solution at definite temperatures. Effects of dezincification were then determined by loss in tensile strength and elongation of the test specimens after definite periods of immersion. In the crystallography of the chemical elements as tabulated by William Hume-Rothery,2 phosphorus (metallic), arsenic, antimony and bismuth are placed in group V-B and the type of crystal lattice for arsenic, antimony and bismuth is given as rhombohedral. The Metals Handbook3 [ ] lists them as "rhombohedral hexagonal," with the additional notation that for arsenic this is the ordinary form at 20°C.; other modifications known or probable at other temperatures. In view of these statements and of the fact that phosphorus, arsenic and antimony are effective in increasing the resistance to dezincification, it was natural to assume that bismuth would act in the same manner. A series of tests was therefore carried out employing the methods described by Barry. Much to our surprise, bismuth did not inhibit dezincification, but rather seemed to accelerate it. Tensile-test speci-

Jan 1, 1942

By E. S. Moore

THE Kolar gold field has been for a long time the most important gold-producing area of India. It is situated in the State of Mysore, southern India, and not far from the City of Bangalore. The productive field is about 3 miles long and in it a gold-bearing quartz vein varying in width from 1 in. to over 10 ft. is worked. The vein carries high values to great depths and many of the mines have paid large dividends. GEOLOGICAL FORMATIONS IN THE MOLAR REGION The rocks of the Molar region are pre-Cambrian in age and bear a close resemblance to some of the pre-Cambrian formations of America. The oldest rocks seen are basic lavas, now mostly altered to hornblende-schists, with which is associated some banded iron-formation; these rocks are similar to the Keewatin schists and iron-formation in the Lake Superior region. The schist is cut by the gold-bearing quartz vein. In certain parts of the area there is also a conglomerate containing pebbles of granite, jasper,, and schist. The matrix resembles a horn-blende-schist and is intruded by small granite dikes, which in some cases have been pinched off by squeezing of the rock. This has led Dr. W. H. Smeeth, Chief Inspector of Mines of Mysore, to whom the writer is greatly indebted for information regarding this area and for his hospi-tality while visiting the field, to regard this conglomerate as a breccia due to crushing of granite dikes in the schist. Dr. J. W. Evans has regarded the conglomerate as probably a squeezed glacial boulder clay. From analogy with pre-Cambrian conglomerates in America, the writer regards it as a metamorphosed rock similar to our basal Huronian conglomerate. However, the main bearing which it has upon the problem under discussion is the apparent fact that it is younger than the schist

Jan 3, 1918

By A. Lee Barrett

Mine power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectional-ized at approximately 2500 ft by means of switches. All, or at least most branch .circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, therefore a fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does considerable damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting. from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V opera-tions, and at I mile intervals or less, in 250V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1949

By A. Lee Barrett

MINE power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectionalized at approximately 2500 ft by means of switches. All, or at least most branch circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, there- fore n fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does consider- able damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V operations, and at 1 mile intervals or less, in 250 V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1948

By Edward H. Robie

AT a recent meeting of the AIME Board there was considerable discussion of a suggestion that companies should be more interested in promoting AIME membership among their employes. The advocate of this idea argued that companies benefit greatly if their employes are active AIME members, so even on purely a selfish basis they should use various means to encourage membership. Also he argued that companies in general make no contribution to the support of the AIMS although benefiting from its work, so should not object to making more of a contribution, financial or otherwise, than they do. One Director stated that an investigation had developed the fact that a large majority of members felt it unwise for employers to pay the initiation fees or dues of employes. They felt that AIMS membership should be on a purely personal basis; that the rewards of active membership were sufficient so that it is a good investment for a man in developing his own professional stature, presumably resulting in an increase in salary sooner, or in greater amount, than would otherwise be the case. If an employer paid a member's dues or initiation fee the member would take less interest in the Institute. But this Director felt that an employer should otherwise encourage his employes to join the Institute, attend its meetings, and write papers based on company work for presentation and publication. Another Director reported that his company pays the expenses of AIME members in its employ to meetings; the company also encourages nonmembers to attend AIME meetings but does not pay their expenses unless they present papers of interest to the company. Another Director, representing a supplier, stated that his company's policy was to send some of its staff to all AIME meetings at which papers of interest were to be presented or at which valuable contacts could be made.

Jan 1, 1952

By D. F. Atkins, B. A. Rogers, E. J. Manthos, M. E. Kirkpatrick

A phase diagram of the uranium-columbium alloys is presented. The apparatus and the procedures used in obtaining the data are described. Data from which the diagram was drawn are given in tabular and graphic form. THE use of uranium in the production of energy from nuclear fission has given considerable im- petus to the investigation of the metal and its alloys. Accordingly, information concerning the phase diagrams of binary alloys of uranium with other elements is of interest to metallurgists engaged in nuclear-engineering activities. As a contribution to the knowledge of the binary alloys, the authors have attempted to establish the diagram of the uranium-columbium system. The reports of laboratories engaged in work for the Manhattan Engineering District and the U. S. Atomic Energy Commission contain a number of references to work on uranium-columbium alloys.

Jan 1, 1959