Search Documents

By A. L. Labbe, J. J. Donoso

Hard-won experience in the operation of smelting plants has pointed the way to the most efficient design and economical operation of a baghouse system for recovery of metallurgical fumes. This paper treats of the principles governing bag filtration and the factors most directly affecting bag life. Methods for temperature conditioning of smoke previous to filtering are described and the evolution of bag shaking mechanisms is brought up to date. THE history of the bag filter process, as applied to the recovery of metallurgical fumes, goes back to 1876, when the Lone Elms Works of Joplin, Missouri, erected a two-section baghouse for filtering fumes from Scotch Hearth lead smelting furnaces. By modern standards this installation was crude, but the basic operating principles remain essentially the same today. Great progress, however, has been made in the mechanization of the process by the use of devices for mechanically and automatically cleaning bags of adhering fumes, in the use of instruments for recording and controlling the variables affecting baghouse operation, and in the conditioning of the smoke previous to filtering. The principles governing bag filtration of fumes were investigated in 1929 by A. J. Seitz of American Smelting and Refining Co., and he arrived at the following conclusions: 1. Pressure on Bags at Constant Volume: The rate at which the pressure builds up in a bag with constant volume is directly proportional to the time, with the same kind of smoke and dust burden (fig. 1). 2. Pressure on Bags for Change in Volume: With equivalent smoke and dust burden, the bag pressure increases with the square of the increase in volume. The rapid increase in pressure is due to (1) increase in volume, (2) increase in amount of dust on the bag, and (3) more intense packing of the dust at higher velocity (fig. 2). 3. Effect of Intensive Filtering on Pressure: Since the pressure builds up directly as the square of the volume, with the same smoke and dust burden, it is necessary to shake the bags in that increased ratio, and vigorously, to keep the pores of the bag open and pressure down. This increases the wear on the bags and the dust losses. 4. Effect of Shaking on Dust Losses: The losses are in direct proportion to the frequency of shaking because the loss takes place immediately after shaking, before the bag seals itself. Tests show that with hand shaking the last 20 pct of the removable dust requires seven times more shaking per unit weight of dust than the first 80 pct. 5. Effect of Fineness of Dust on Losses: The fineness of the dust particle increases the loss in two ways: (1) When the bag is clean a greater percentage of it will pass through before the bag seals itself; (2) fine material penetrates farther into the bag pores, building up pressure faster and necessitating more shaking, thereby increasing the loss. The physical principle of operation of the bag filter is simply the separation of solids from a gaseous carrier through a porous medium, and is analogous to the filtration of solids from liquid carriers. Basically, the mechanics of the process are as follows: Fume-laden gases drawn from the operating fur-

Jan 1, 1951

By August Wendel

It is a well-known fact to all Bessemer steel manufacturers using a blooming mill, that ingots show large cracks in the first few passes of the rolls, which, in the following ones, do not always roll up satisfactorily. This deficiency in the quality of the product is generally called "red-shortness," though, in the writer's opinion, mostly unjustly so. Different explanations for the said peculiarity are given by the leading authorities, each works selecting one element as a special scapegoat for the inferior quality of the ingot. The sulphur is generally first charged as being the principal cause of all mischief in this direction ; then, after ascertaining that sulphur is not higher than the average, and sometimes lower in the very worst heats, silicon has to bear its share of abuse. How and why silicon should affect the working qualities of the metal, the writer could never precisely learn, but is convinced that the doctrine of its pernicious influence is an established one with many. In cases where silicon failed to explain everything, resort was taken to calcium, aluminum, and some other known or unknown elements, without settling the difficulty; and lastly, when the skill of the chemist became exhausted, " practical men " came to the same conclusion, which many leading blast-furnace managers had arrived

By T. R. Wright

IN few mining regions in the world are the ores so varied and complex as in the Andes of central Peru. Consequently, in few localities is one company engaged in so many and such diverse metallurgical operations as the Cerro de Pasco Copper Corp. Concurrent with the mining of complex lead-zinc ores in Peru, and the consequent expansion of the Corporation's metallurgical activities, a department of metallurgical research was established in 1927 at La Orova. Facilities were provided for research in ore dressing, hydronivtallurgy pyrometallurgy, electrometallurgy, and analytical chemistry. In addition to laboratories. various pilot plants were built, including a concentrator, leaching plant, "by-product" smelter, and electrolytic refineries. These pilot plants are not diminutive units; they are designed and equipped as semicommercial plants for operation on a continuous 24-hour basis thus assuring the duplication of pilot plant results in actual practice. In general, the sequence in the development of metallurgical operations hasbeen as follows: (1) investigations in the laboratory to determine the most effective and economical method of treatment; (2) continuation of the research project on a pilot-plant scale when the evaluation of the laboratory

Jan 1, 1945

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut, and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States, 2 and in addition, feldspar is produced as a byproduct by firms whose major products are spodumene and mica. 3 Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan, and the USSR. According to the US Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 and 2,514,000 t, respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel, tile, and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, NC, have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water containing 0.9-1.0 ppm fluoride will seldom cause mottled enamel on children's teeth; and for adults, concentrations less than 3-4 are not likely to cause endemic cumulative fluorosis and skeletal effect. Although the literature on this subject is rather confusing and inconclusive, the inference that concentrations over 4 ppm may affect bone structure is clear. According to the recent Federal Register,4 maximum fluoride level of 1.4 ppm at 79°-98°F is considered to be adequate and safe for the protection of health of the consumers. The EPA and state environmental agencies have accelerated their drive to reduce water pollution on a faster schedule. By 1977, the EPA specifications for maximum contaminant level of fluoride ions in the discharge waters of feldspar milling operatins is expected to be reduced to 2.0 ppm. The other problems of using hydrofluoric acid are the following: toxicity, hazards of handling and storage, and high cost as compared to other inorganic acids (almost 16 times the cost of sulfuric acid). In order to reduce fluoride levels in mill discharge waters, mining companies have taken the following steps: I) Recirculating a part of their mill water. Even though recirculation of mill water seems to be a novel method of reducing fluoride contamination of the discharge water, there are certain operational and handling problems. 2) Conducting research on the treatment of fluorides in mill waste water. The technology of treatment of fluoride ions has received considerable interest in the recent years. A recent research report5 estimates that the cost of fluoride ion removal to meet the present specifications in the feldspar industry is approximately $0.25/t of ore processed, and about $0.50/t of feldspar produced. At the request of the feldspar producing industries in North Carolina, the North Carolina State University (NCSU) Minerals Research Laboratory has taken up a research program directed towards overcoming the fluoride ion pollution problem. After a close study of the operational, technical, and economic aspects of feldspar flotation, it was decided to attempt to replace the conventional hydrofluoric acid process. Conventional Feldspar Flotatin Using Hydrofluoric Acid Since the inception of the feldspar flotation process using hydrofluoric acid by O'Meara2,6 the process has achieved a great commercial success. In the conventional flotation separation of feldspar-quartz, hydrofluoric acid is used to suppress quartz and activate feldspar, and a long chain amine salt (acetate or chloride) is used as a collector. The bulk of amine collectors used in current feldspar operations are applied as the water-soluble acetates of the free-base amines. These products are pastes or waxy solids which are available in a range of acetic acid neutralization levels generally 50 to 100% neutralized. In spite of the problems mentioned in connection with the use of hydrofluoric acid, this process is extremely stable with respect to changes in the process variables. With the exception of a few operations, alaskite and pegmatite are the major sources of feldspar.7 In the flotation treatment of a pegmatite that contains iron-bearing minerals (heavy minerals), mica, feldspar, and silica, a logical order of removal presents itself considering the following:8 1) Mica is readily floated by an amine collector in a pulp pH 3.5. Some iron-bearing minerals will usually respond to amine collector in acid circuit with the mica concentrate. 2) Since iron minerals tend to occur invariably in the feldspar concentrate, it is desirable to remove most of these prior to feldspar flotation. A fatty acid or a petroleum sulfonate collector used in this flotation step in acid circuit will float iron-bearing minerals. 3) Using hydrofluoric acid to maintain pH of 2.5, an amine collector employed in a final step will float feldspar away from silica, usually leaving the latter in the tailing as a high-grade silica concentrate. The problems connected with the flotation separation of feldspar-quartz arise due to the similarities in their chemical structure. Therefore, any reagent system that is likely to succeed in feldspar-quartz separation should have adsorption affinity towards one of the minerals and depression effect towards the other mineral.

Jan 1, 1979

By N. B. Davis

I. Introduction. II. Definition of Plasticity. III. Theories of Plasticity. A. Structure of the clay particles. (1) Fineness of grain. (2) Plate structure. (3) Interlocking particles. (4) Sponge structure of particles. B. Presence of hydrous aluminum silicates. C. Molecular attraction between particles. D. Presence of colloidal gelatinous matter. (1) Review of theory of colloids. (a) Suspension colloids. (b) Emulsion colloids. (2) Experiments. IV. The Formation of Clays. A. Residual clays. B. Transported clays. V. Summary. VI. Conclusion. I. IntRodUction While working with a number of very sticky cracking clays from western Canada the writer became interested in a study of the cause of the excessive plasticity. This led to a review of the rather bulky literature on the subject and the finding that plasticity still remains to be satisfactorily explained. Most of these investigations seem to have been carried on solely from the chemical viewpoint, the geologic aspects having been ignored. In nearly every case, the investigators have worked with the higher-grade clays of low to medium plasticity, such as the kaolins, the excessively plastic ones having generally been neglected, partly because of their limited application, yet the author believes that these are

Jan 1, 1915

By G. E. Agar, P. L. De Bruyn

Flotation is an important example of a chemical process by which one solid may be separated from other solids in a mixture. In contrast to other chemical processes such as leaching and smelting, separation of solids by flotation is characterized by the establishment of contact among three phases. In froth flotation these three phases are the solid to be floated, an aqueous electrolyte solution, and a gas, usually air. The gaseous phase may be re- placed by an organic liquid phase or this organic liquid phase may be added deliberately as a fourth phase. To gain an understanding of the flotation sys- tem, it is therefore necessary to study the chemical and physical properties of surfaces and to establish the effect of changes in composition of the bulk phases on the nature of the three interfaces, solid-gas, solid-liquid and liquid- gas. With very few exceptions inorganic solids are completely wetted by the aqueous phase so that the first step in flotation is to replace partially the solid-liquid interface by a solid-gas interface. This displacement process is accomplished by the addition of suitable reagents to the aqueous phase. The resultant surface reaction leaves the solid surface with a hydrophobic film. Although the primary objective of these reagent additions is to alter the solid surface, chemical reactions between the added chemical species and those species derived from the dissolution of the solids are unavoidable. For a quantitative description of such reactions and for the determination of the feasibility of a proposed reaction, we rely on available thermodynamic data. The application of thermodynamic principles to flotation systems has contributed much to our understanding of flotation. The changes in thermodynamic properties such as free energy and chemical potential are accessible to experimental determination, and a knowledge of their magnitude allows us to develop and predict a chemical mechanism oy which a solid becomes floatable. In this chapter it will be assumed that the reader has a working knowledge of the general principles of thermodynamics and solution chemistry. A complete discussion of the physical chemistry of flotation must include a treatment of solubility relations, complex ionic equilibria, reaction potential, and the elements of electrochemistry, especially those dealing with reversible electrical cells. The principles related to all of these features of the flotation system will not be discussed in this chapter. The discussion will be concerned with the thermodynamics and electrochemistry of surfaces and the electrical double layer model of the interface.

Jan 1, 1962

By J. B. Hess, C. S. Barrett

Single crystal rods of cadmium collapse under uniaxial compression into peculiar kinks if the (0001) glide plane is nearly parallel to the axis of compression. In his report first describing this behavior, Orowan1 proposed that these "kink bands" do not develop entirely by ordinary gliding and twinning but by a special mechanism in which glide lamellae of uniform thickness snap abruptly to a tilted position that permits lattice continuity across the glide planes. He concluded that a portion of each boundary of a kink band consists of a plane (non-crystallo-graphic) which bisects the angle between the glide planes on the two sides of it, and along which the bending and the dislocations are concentrated. The data presented by Orowan seemed to us to be insuffcient to conclude that a wholly new mechanism of deformation was responsible for the kinks. Therefore, we have investigated zinc, which is hexagonal close-packed and has an axial ratio near to cadmium, to see whether similar bands are produced, and whether the ordinary mechanisms of glide, bend-gliding, twinning, and the formation of deformation bands can account for its mode of deformation. We find that kinks form profusely in zinc as shown in Fig 1. The structure of these kinks, reported below, seems to require no new mechanism for their explanation, but indicates that kink bands are a special form of deformation bands and develop gradually, solely from basal glide. A theory covering the formation and structure of the bands is presented in detail because it is seldom possible to study deformation bands under such simple conditions, yet many principles applying to these kinks should also apply to deformation bands in general. Experimental Procedures Single crystal rods of 2-3 mm diam and 10-15 cm length were grown by the Brideman technique from swaged wire of Horsehead Special zinc in un-coated pyrex tubes. Orientations of the rods were determined with an optical goniometer after cleaving the rods at liquid air temperature. Crystals of desired orientations were then selected and used as "seeds" to grow additional crystals approximately 4 ft in length from which all specimens were cut. The wires were compressed in two ways: in a simple hydraulic handpress —a "soft" machine—and in a Riehle hydraulic testing machine modified to produce very "stiff" action by the simple expedient of inserting lengths of steel bars at the sides of the zinc crystals between the compression plates. For metallographic examination, the specimens were mounted in sealing wax. Hand polishing was employed, with no grits coarser than No. 1 paper; following the abrasives about 0.025 in. was removed by an etch-polishing reagent.* Final etching to reveal ori-

Jan 1, 1950

By Clarence Zener, Howard Clarke, Cyril Stanley Smith

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By Howard Clarke, Cyril Stanley Smith, Clarence Zener

The importance of cold-working in the fabrication of metals is in marked contrast with our ignorance as to the nature of the accompanying internal changes. The failure of the usual methods of testing to provide a consistent picture of these internal changes has given the incentive for the present program of investigating the effect of cold-working upon the internal friction of metals measured at small strain amplitudes. It has previously been shown1,2,3, that the internal friction introduced by cold-work is removed by annealing at comparatively low temperatures. In the present paper the following additional factors are investigated: (I) frequency of measurement, (2) amount of cold-work, (3) temperature of measurement. Special care was taken to minimize the internal friction due to causes other than cold-work. The present paper is purely experimental, the authors believing that any conclusions drawn from this work as to the nature of the internal changes accompanying cold-work would be premature.'l PrEpaRations oF Specimens In this study of cold-work it was desirable to eliminate as far as possible all other sources of internal friction. One disturbing source is the lack of temperature equilibrium between adjacent crystallites of a vibrating specimen.4 Temperature equilibrium is aided by small grain size and by the use of low-frequency vibrations. Unless unduly long specimens are used, low frequencies can be obtained only in transverse vibrations. But in transverse vibrations a second source of internal friction is present, that arising from transverse thermal currents.5 The effect of these may be reduced by increasing the transverse dimensions. The grain size and transverse dimensions of the specimens were thus so chosen as to render the vibrations simultaneously nearly isothermal with respect to intercrystalline thermal currents, and nearly adiabatic with respect to transverse thermal currents. The material for this investigation was a 70-30 brass, part of the same lot of material that was used for some earlier studies on the effect of strain on proportional limit.10 It had the following composition: copper, 70.59 per cent; zinc, 29.39; lead, 0.01; iron, 0.01. This material was received from the brass mill in the form of 3/4-in. rod, cold-drawn to final size by a 65 per cent reduction of area from material that had been annealed to give a grain size of 0.060 mm, Rods of appropriate length were annealed for 2 hr. at 400°C. and cooled in air. The annealed rods (grain size, 0.012 mm.) were then stretched in a tension-testing machine, using special grips1' to ensure axial application of the load. The rate

Jan 1, 1942

By E. L. Larison

DURING the early years of the present century a notable interest appeared in American industry in the matter of recovering and render-ing profitable byproducts of manufacturing operations. Among the byproducts of reduction of sulfide ores in many plants large amounts of sulfur dioxide gas were available. In certain instances the concentration of S02 in the gases evolved was, or could be made, sufficient to make them suitable for manufacturing sulfuric acid. At the Anaconda Reduction works such a condition existed. Large tonnages of copper concentrate were being roasted and the roaster gases were available and suitable as a source of sulfuric acid. Earlier work on a large scale at Martinez, Calif., and in the Ducktown region, Tennessee, had shown the feasibility of manufacturing sulfuric acid from the S02 contained in gases arising from the reduction of copper sulfide ores. In California and Tennessee the acid found a ready market in manufacture of fertilizers, while the situation regarding disposal of the sulfuric acid was quite different at Anaconda. No local use for acid existed, and a commodity of such low value could not stand freight charges to consuming centers. There was a very large accumulation of sand tailings from the gravity concentration mill below the plant at Anaconda. This material, made by the comparatively crude methods in use up to about 1915, contained about 13 lb. of copper per ton, largely as sulfide minerals. In 1912 serious research work toward recovery of this copper was instituted and after about two years of laboratory and pilot-plant development, a process for accomplishing it was perfected. This process involved roast-ing the sand tailings, leaching the roasted tailings with sulfuric acid, and throwing out the copper by passing the solutions over scrap iron. Under this plan each ton of sand required the introduction of about 70 lb. of 60° Be. sulfuric acid.

Jan 1, 1934

By Howard Eavenson

IN a discussion in the Transactions of the Institute (vol. xl, page 835 et seq.) the writer gave some data about explosions of gas and dust in the coal mines of the United States, Canada, and Mexico, among which was a table showing all explosions in the countries mentioned, in which five or more fatalities occurred, which had been reported from Oct. 2, 1871, to Mar. 28, 1908. Since the elate of publication of this discussion, as opportunity has presented, this table has been extended by the addition of explosions occurring since that time, by including several explosions which occurred prior to 1871, and by adding to the list all explosions of gas or dust in which less than five fatalities occurred, this having been clone by a search through the various mine reports, partly by the author and partly by the Librarian of the United Engineering Societies, and by correspondence with mine inspection officials of the various States, to all of whom acknowledgment of assistance is made: The accompanying list, Table I, is believed to be as nearly correct as such a statement can be made, and, while only extending to Dec. 20, 1912, contains all of the data now available in reports. An analysis of Table I, showing the occurrence by months of all explosions of gas or dust, including those in which less as well as those in which more than five fatalities occurred, is given in Table II. The statements are frequently made, in technical papers, that the number of explosions, particularly the larger ones, is increasing more rapidly than the number of mines, and that the number of fatalities caused by mine explosions, particularly the more disastrous ones, is increasing faster, proportionally, than the production of coal. To investigate the correctness of these statements Table III was prepared, in which the number of accidents and fatalities is taken from Table I, using those in the United States only, on account of lack of other data for Canada and Mexico; the production is from the records of the U.S. Geological Survey, and the number of mines, from 1909, from the same source; previous to 1909, the number of mines, for the decennial periods, was furnished by the U. S. Census records.

Jan 10, 1914

By H. J. Hand

STATISTICAL methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,' written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science,, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should .they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. † Many Useful Statistical Devices Available.-Many statistical methods of attack are available for the analysis of plant data. It is the object of this paper to discuss applications of some of these methods to the solution

Jan 1, 1938

By C. R. Holmgren

A large consolidated sand core was used in this investigation. Four groups of experiments including gas drives, water drives, and water drives combined with gas injection, were made. The results of the gas-drive experiments indicate that greater ultimate recovery may be obtained by higher pressure gradients. However, other considerations challenge the absolute veracity of this conclusion. Results indicate that with connate water present and a low pressure gradient during a gas drive, less gas is required to produce a given amount of oil. The saturation gradient determined during a gas drive is presented. Results of the water-drive experiments indicate that the recovery of oil is not a function of either gradient Or input rate. The presence of initial gas saturation resulted in a slightly lower final oil saturation. Injection of sufficient gas to maintain the initial gas saturation during a water drive resulted in lower final oil saturation. Introduction With the demand for petroleum products reaching an all-time record high and the location and exploitation of new reserves becoming more difficult and expensive, the oil industry must look to more thorough and efficient methods of producing the petroleum already located. Much of the previous work along these lines is exploratory and suggests a more complete investigation. For example, a great amount of laboratory work has been done on flooding sands initially saturated roo pct with oil. Since sands saturated roo pct with oil rarely, if ever, exist in nature, and because the water content is a vital factor in the ultimate recovery from the sand, laboratory investigations on cores without water must be supplemented by comparable work on cores with water present.1'2 Other investigators have done a considerable amount of laboratory work using gas and water drives.3 Krutter and Day4 have reported results of investigations using cores saturated IOO pct with oil and have concluded that " the ultimate recovery obtained, using air drive, from a completely oil-saturated core depends on the pressure gradients used. The higher the pressure gradient, the greater will be the recovery until a certain Pressure range is reached above which the reward of increased recovery is much smaller for similar increments in pressure." Yuster and Day6 conclude that less gas and less time are required to produce a given quantity of oil at high pressure gradients than at low pressure gradients; they also conclude that an increase in the viscosity of the oil requires a proportionate increase in the gas needed for recovery. Their results indicate that the gas required to produce a given quantity of oil is greatly reduced by the presence of connate water. R. C. Earlougher2 concluded, based on results of water-flooding a large number of

Jan 1, 1949

By F. C. Holden, R. D. Buchheit

In the course of studies made on the Ti-Cu alloy system,' particles identified visually as TiH were encountered unexpectedly in a specimen of high-purity Ti-0.8Cu alloy. The particles did not appear immediately after preparation, but following-storage in a dessicator for several days. Since the alloy had been vacuum annealed to a low hydrogen concentration (19 ppm by vacuum-fusion analysis), the appearance of the TiH particles was suspected as a surface contamination effect. A specimen of a Ti-0.8Cu alloy had been annealed 2 hr at 790°C and water quenched, to produce the single-phase equiaxed a structure. The metallo-graphic sample was ground through 600X paper, rough-polished on a high-speed wheel with a mixture of alumina and chromic acid, awLhish-polished on a slow-speed wheel. Disturbed metal layers were removed from the final surface by alternately etching with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution and polishing on the slow-speed wheel with fine alumina. The final surface was swab-etched with a 1 1/2 HF-3 1/2 HNO3-95 H2O solution, rinsed in tap water, and dried in a stream of filtered air. The micro-structure, shown in Fig. 1, was composed of equiaxed a grains without any trace of second phase. After storage in a dessicator for 3 days, the appearance of small particles in the structure became evident (see Fig. 2). After 7 days of storage, the particles were more distinct, and in some grains, began to appear as elongated particles. The specimen then was etched a second time (without repolishing) to produce the structure shown in Fig. 4. On the basis of micro- structural observation, the line markings were identified as TiH; attempts to obtain diffraction patterns from the surface for positive identification were not successful. That the structure is a surface effect was demonstrated by grinding with 240X paper to remove the surface layer. The surface then was ground, polished, and etched using the procedures described previously. The same observations were made: the freshly prepared surface was devoid of any second phase, whereas the particles again appeared after several days storage. The same effect has been observed in other a-stabilized titanium alloys, including a high-purity Ti-0.20 alloy containing only 16 ppm H by analysis. The effect has not yet been observed in unalloyed titanium, nor does its appearance appear to be consistent with any particular alloy system. From these observations, it is concluded that certain a-titanium alloys are susceptible to the formation of titanium hydride at the surface of metallo-graphic specimens. The hydrogen probably is diffused into the surface from a residual film of etchant decomposition products. Estimates of the hydrogen

Jan 1, 1961

By Peter R. Morris, Alan J. Heckler

THREE angles are required to specify the orientation of a crystallite with respect to a physical reference frame. The distribution of crystallite orientations in a polycrystal is thus a function of three angular variables. The most widely used experimental techniques for studying orientation in polycrystals lead directly to the pole figure representation, i.e., the distribution of the poles of certain crystallographic planes in terms of two angular variables. In recent years1-5 methods have been developed which permit determination of the (three-angle) crystallite orientation distribution from several (two-angle) pole figure distributions. In this work Roe's method has been applied to the study of orientation in hcp materials. The method is illustrated for commercial purity titanium sheet (Ti-70) which was cold rolled (65 pct reduction), annealed at 1450°F for 3 min, and air cooled. The grain shape was observed to be equiaxed after this treatment. EFFECTS OF PHYSICAL, CRYSTALLOGRAPHIC SYMMETRY In Roe's method the crystallite orientation distribution, w(?,?,F), is expanded in a series of generalized spherical harmonics 11(?,?,F) = E E E W^Zirmtye-tote-in* [l] 1=o ,,,=-I ,,=-I where { = cos 8. The set of Euler angles employed here is illustrated in Fig. 1. The axis for each rotation is denoted by a double arrowhead. The positive sense of each rotation is that of a right-handed screw advancing in the direction of the double arrowhead. The X, Y, and Z directions correspond to the rolling direction, cross direction, and normal direction, respectively. In the initial orientation (10.O), (12.O), and (00 . 1) planes are perpendicular to the X, Y, and Z directions, respectively. The IC/ rotation about the Z axis is carried out first by rotating X into X', Y into Y', and leaving 2 unchanged, i.e., Z' = Z. The 8 rotation about the Y' axis is carried out second by rotating X' into X", 2' into Z", and leaving Y' unchanged, i.e., Y" = Y'. The I$ rotation about the Z" axis is carried out last by rotating X" into X"', Y into Y"', and leaving 2" unchanged, i.e., 2"' = 2". Any specified orientation of the X'", Y'", and Z'" crystal-fixed axis system relative to the X. Y, and Z physical axes (rolling direction, transverse direction, and sheet normal direction, respectively) can be obtained by appropriate IC/, 8, and (F rotations. The Zl,, of Eq. [l] are the Jacobi polynomials, augmented by the square root of the weight function. The Zl,, are symmetric in m,n, i.e., Zl,,= Zlnm. For orthotropic physical symmetry and hexagonal crystallographic symmetry, the coefficients, W!,,, of the series are all real, W!mn = Wzfi, = Wlm~ = Wlfi~, 1 and m are even and n is restricted to 6k, where k = ...,-2,-1, 0, 1, 2, .-.. The determination of the Wlmn from pole figure data has been previously described.'~~ The Zl,, may be written in multiple angle form

Jan 1, 1970

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By George Rice

INSTANTANEOUS outbursts of gas in underground workings are similar in effect to great blasts of explosives, but without heat effects. Fortunately they occur only in a few localities in exceptional coal fields of the world and under exceptional geologic conditions. Such violent outbursts should not be compared with the ordinary outflows of gas into coal mines or with explosions of gas and dust. The phenomenon is essentially one of gas held in circumscribed areas under very high pressure and as a mining face or heading approaches such a place and the mining excavation sufficiently weakens the natural surrounding dam or shell, this is burst by the pressure just as by the discharge of a mass of explosives. The outbursts, so far as known to the writer, have been confined to coal beds and have not occurred in other mineral deposits. Hence, as discussed later, he believes that it is the relation of the gases to the coal material that is a factor in conjunction with others in producing conditions which permit the phenomena to occur when mining is done. The gases in most instantaneous outbursts have been hydrocarbon gases but in two coal fields they have been definitely found to be chiefly or wholly carbon dioxide. One of these localities in which CO2 outbursts have been frequent and have caused loss of life is in the southern part of the Gard basin, near Alais, in southern France. In 1919, the writer visited the Fontaine mine in this field the day following the occurrence of an outburst by which two men were smothered by carbon dioxide and fine dust. After 24 hr. the CO2 had not been entirely removed by the ventilating current. Occasional outbursts of CO2 have also occurred in other small basins in France, causing accidents, as in Puy-de-Dome. However, mines in the Gard basin, north of those in which CO2 outbursts have occurred, have experienced hydrocarbon gas outbursts.

Jan 1, 1931

By T. N. Williamson

6.3-1. Historical Development. Rotary drilling has been used in surface mining for many years. Its principal use is for primary blasthole drilling. In this use, holes in the range from 4 to 15 in. in diameter are drilled in overburden and massive ore bodies for large initial blasting operation. With properly designed shot patterns and loading, secondary blasting is seldom required. The use of rotary drilling with diamond bits for exploration is discussed in Chapter 3.1. Small rotary drillholes of approximately 2-in. diameter are employed as blastholes to shatter uncovered coal seams, but this is a minor part of surface mining drilling operations. Another minor use of rotary drills in surface mining is for placing wire saw poles in dimension stone quarries, usually accomplished with large-diameter calyx or steel shot drills. Primary blasthole drilling by the rotary method was performed with drag bits until 1949 (19). Its use in mining was only in soft formations, so that rotary drills prior to that time were found principally in overburden drilling for the surface mining of coal. In 1949 it was found that air circulation to remove cuttings resulted in increased penetration rate and prolonged life for the rolling-cutter type of bits. Prior to that time, and since their introduction in oil well drilling in 1907, water had been used for circulation with these bits. The dependence on water to clean the hole had delayed the acceptance of bits with rolling cutters in mines because of water haulage and freezing problems as well as the loss of water through cracks in the formation. After rolling cutters were introduced, subsequent improvements in tools made rotary drilling adaptable to harder formations (18). This system is now used in the hardest formations encountered in mining. 6.3-2. Principles of Operation. ENERGY. Rotary drills attack rock with energy supplied to the bit by a rotating drill stem, and infrequently by

Jan 1, 1968

By T. F. Archbold, P. G. McCormick

Silica fiber 11arkevs and hardness irzdentatiozs have been used to study the thermal diffusion of racancies in zinc placed in temperature gradients of 460o and 706oK per Cm All markers mored toward the higher temperatures, and the data show that the heat of trarlsport Q is greater than the eizthalpy of z,acancj3 forrjalion E by an amount equal to 3.5 kcal per mole. These results ore not in agreement with those obtained in either of the two previous studies with zinc. The problem is discussed in terms of experimental differences and racancy source and sink efficiencies. THE general interest in thermal-diffusion phenomena over the past several years has prompted a number of marker movement studies using pure metals. In order to understand better the relationships between thermal and mass flow, a general goal of the experiments has been to obtain values for the net enthalpies carried by the diffusing atoms. For self-diffusion by means of the vacancy mechanism, the determination of relative marker positions before and after an anneal in a temperature gradient permits a calculation of a value for (Q - Ef). Q is the transferred enthalpy, and Ef is the enthalpy of vacancy formation in the metal being investigated. The initial experimental study of thermal diffusion in pure metals was accomplished by Shewmon who found essentially no movement of surface-hardness indentation markers in single and bicrystals of zinc held for 20 days in a temperature gradient of 310°C per

Jan 1, 1967