Search Documents

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity air¬borne gamma ray spectrometer with large volume NAI(Tl) crystal detectors. The high-sensitivity spectrometer measures small variations in the concentration of potassium (as Ks°), thorium (as Tl308) and uranium (as Bi.214) along the flight lines in the area surveyed. Hydrothermal dispersion patterns are indicated by anomalous measured values of the concentrations of potassium, thorium, uranium, or their ratios. In two recent Australian survey areas, copper mineralization was located along favorable structures within hydrothermal dispersion patterns delineated by airborne geochemical surveys. In metamorphic terrane where there had been po¬tassium metasomatism, the hydrothermal dispersion patterns were indicated by high potassium/uranium ratios (K40/Bi). In a sedimentary environment that had been intruded by a stock, the path of hydrothermal fluids was indicated by uranium (Bi214), thorium (TV'), and uranium/ thorium (Bi214/Tl208) ratios.

Jan 1, 1972

By F. E. Werner, B. L. Averbach, Morris Cohen

THAT bainite formed near the M, temperature bears a striking r esemblance to martensite tempered at the same temperature has been shown by the electron microscope.' By means of electron diffraction,' it has been established that carbide and cementite are present in bainite formed at 500°F (260°C); these carbides are also found in martensite tempered at 500°F (260°C).' The investigation reported here is concerned with an X-ray study of the matrix phases in lower bainite and tempered martensite. These phases have turned out to be dissimilar in structure; the matrix of bainite is body-centered-cubic while that of tempered martensite is body-centered-tetragonal. A vacuum-melted Fe-C alloy containing 1.43 pct C was studied. Specimens of 16 in. diam were sealed in evacuated silica tubing and austenitized at 2300°F (1260°C) for 24 hr. One specimen was quenched into a salt bath at 410°+7 °F (210°+4°C), held for 16 hr, and cooled to room temperature. The structure consisted of about 90 to 95 pct bainite, the re: mainder being martensite and retained austenite. A second specimen was quenched from the austen-itizing temperature into iced brine and then into liquid nitrogen. It consisted of about 90 pct martensite and 10 pct retained austenite. The latter specimen was tempered for 10 hr at 410°+2°F (210°+1°C). The specimens were then fractured along prior austenite grain boundaries (grain size about 2 mm diam) by light tapping with a hammer. Single aus-tenite grains, mostly transformed, were etched to about 0.5 mm diam and mounted in a Unicam single crystal goniometer, which allowed both rotation and oscillation of the sample. Lattice parameters were measured by the technique of Kurdjumov and Lyssak. This method takes advantage of the fact that martensite and lower bainite are related to austenite by the Kurdjumov-sachs orientation relationships Thus, the (002) and the (200) (020) reflections can be recorded separately, permitting the c and a parameters to be determined without interference from overlapping reflections. According to these findings, the matrix phase in bainite is body-centered-cubic and, within experimental error, has the same lattice parameter as ferrite (2.866A). On the other hand, martensite, tempered as above, retains some tetragonality, with a c/a ratio of 1.005t0.002. Most workers in the past have assumed that bainite is generated from austenite as a supersaturated phase, but the nature of this product has not been established. The question arises as to whether bainite initially has a tetragonal structure and then tempers to cubic, or if it forms directly as a cubic structure. If it forms with a tetragonal lattice, it might well be expected to temper to the cubic phase at about the same rate as tetragonal martensite. The martensitic specimen used here was given approximately the same tempering exposure, 10 hr at 410°F, as suffered by the greater part of the bainite during the isothermal transformation. About 50 pct bainite was formed in 6 hr at 410°F. On tempering at this temperature, martensite reduces its tetragonality within a few minutes to a value corresponding to 0.30 pct C.' Further decomposition proceeds slowly, and after 10 hr the c/a ratio is still appreciable, i.e., 1.005. Thus, even if the bainite were to form as a tetragonal phase with a tetragonality corresponding to only 0.30 pct C, which might be assumed to coexist with e carbide, it would not be expected to become cubic in this time. It seems very likely, therefore, that bainite forms irom austenite as a body-centered-cubic phase and does not pass through a tetragonal transition. The carbon content of the cubic phase has not been determined, but it could easily be as high as 0.1 pct, within the experimental uncertainty of the lattice-parameter measurements. It has been postulated that retained austenite decomposes on tempering into the same product as martensite tempered at the same temperature. There is now considerable doubt on this point. The isothermal transformation product of both primary and retained austenite at the temperature in question here is bainite," and the present findings show that bainite and tempered martensite do not have the same matrix. Acknowledgments The authors would like to acknowledge the financial support of the Instrumentation Laboratory, Massachusetts Institute of Technology, and the United States Air Force.

Jan 1, 1957

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

(Members are urged to send in for this column, any notes. of interest concerning themselves or their fellow-members.) The following members registered at Institute headquarters during the month of May: Emil Gathmann, Baltimore, Md. Philip Argall, Denver, Colo. Albert H. Fay, Washington, D. C. A. C. Hodge, F.R.G.S., St. Austell, Eng. Alfred E. Barlow, Montreal, Canada. S. M. Marshall, Johnstown, Pa. B. C. Yates, Lead, S. D. Miltiades Armas, Paris, France. Leonard S. Austin, Salt Lake City. Albert Sauveur, Cambridge, Mass. Henry A. Wentworth, Boston, Mass. G. A. Reinhardt, Cambridge, Mass. Frank M. Leland, Mackay, Idaho. Fred Crabtree, Pittsburg, Pa. W. N. Crafts, Cleveland, Ohio. T. A. Rickard, London, England. Louis Hasbrouck, Kingston, N. Y. F. Lynwood Garrison, Philadelphia, Pa. F. V. Desloge, Desloge, Mo. S. B. Christy, Berkeley, Cal. E. C. Templeton, Palo Alto, Cal. H. A. Buehler, Rolla, Mo. L. D. Ricketts, Warren, Ariz. F. W. DeWolf, Urbana, Ill. J. E. Johnson, Jr., Ashland, Wis. Howland Bancroft, Denver, Colo. A. O. Granger, Cartersyille, Ga.

Jan 6, 1913

By R. R. Hart, B. C. Wonsiewicz, G. Y. Chin

In recent years there has been increased miniaturization of electromechanical devices to keep pace with current trends toward smaller electronic components. A major problem facing the designer, however, is the higher stresses encountered by the material as a result of shorter springs. Hence an improvement in the elastic limit, as approximated by the 0.01 pct offset yield strength, would be highly desirable. An increase of 25 pct in the yield strength, for example, will permit a 20 pct reduction in both the length and thickness of a cantilever-type spring while maintaining the same compliance. One technique of improving the yield strength that has received little commercial attention is crystal-lographic texture strengthening.1,2 Texture strengthening is expected to be most beneficial in materials of hcp structure, but considerable gain can also be expected in cubic materials. A wire with a (111) fiber texture, for example, is expected to be 20 pct stronger than randomly oriented material, and 50 pct stronger than wire with a (100) fiber texture.293 For sheet specimens with a {110}(112) texture, characteristic of many heavily rolled fcc alloys, the (111) transverse direction is expected to be the maximum yield strength direction, about 20 pct higher than that in the (112) rolling direction.' In addition, the (111) direction is the direction of maximum modulus of elasticity for most cubic alloys. A large value of the elastic modulus could be desirable in designs where stiffer springs are required. To test the above idea, a 0.090 in. (-2.3 mm) thick commercial grade A (5 pct Sn) phosphor bronze sheet, a widely-used material for relay springs, was rolled from the spring-tempered condition (60.5 pct reduction) to various additional reductions up to a total reduction of 95 pct. Subsequently, additional material was obtained with a total thickness reduction of 97.3 pct Standard tensile specimens were prepared from the sheet material with the tensile axis parallel to and at 90 deg to the rolling direction. Tests were run on an Instron testing machine at a strain rate of about 0.050 min-l. Textures were determined by the use of the reflection pole-figure technique. Data were obtained using nickel-filtered CuKa radiation and with the aid of a Siemens pole figure goniometer. The X-ray pole figure studies show an incrzasing development of the texture toward the {110}(112) ideal

Jan 1, 1970

By C. C. Singleterry, D. L. Katz

The critical phenomena have been studied during the past century but our knowledge of the critical temperatures and pressures of complex hydrocarbon mixtures still is very limited. The critical temperatures and pressures of pure substances have been examined in large numbers120 and in great detail.11.17 No experimental determinations of the critical phenomena have been reported on such complex hydrocarbon systems as a reservoir fluid. The critical temperature is defined by Taylor18 as follows: "there is some temperature for each gas above which the gas cannot be liquefied. This temperature is called the critical temperature." The critical pressure of a pure substance is the vapor pressure at the critical temperature. It should be noted that these definitions refer to a given substance in the pure state and do not mean that the pure substance cannot be liquefied in the presence of a second constituent. The normal procedure for obtaining the critical temperature of a substance is to heat it in a glass tube 1,20 under pressure until the meniscus between the liquid and vapor phase disappears, although other methods, especially for mixtures, have been used.13,14 However, when considering oil and gas reservoirs, it is more enlightening to consider a critical phenomenon that occurs when a mixture of oil and gas are compressed at a reservoir temperature until the meniscus disappears because the two phases become equal in composition. This conception, along with erroneous applications of the definition of the critical phenomena of a pure substance to that pure substance when it is part of a complex mixture, has caused confusion even among persons familiar with the classical theories. The purpose of this paper is to discuss the critical phenomena of pure substances and mixtures and to report experimental data on a mixture of

Jan 1, 1939

By C. C. Singleterry, D. L. Katz

The critical phenomena have been studied during the past century but our knowledge of the critical temperatures and pressures of complex hydrocarbon mixtures still is very limited. The critical temperatures and pressures of pure substances have been examined in large numbers120 and in great detail.11.17 No experimental determinations of the critical phenomena have been reported on such complex hydrocarbon systems as a reservoir fluid. The critical temperature is defined by Taylor18 as follows: "there is some temperature for each gas above which the gas cannot be liquefied. This temperature is called the critical temperature." The critical pressure of a pure substance is the vapor pressure at the critical temperature. It should be noted that these definitions refer to a given substance in the pure state and do not mean that the pure substance cannot be liquefied in the presence of a second constituent. The normal procedure for obtaining the critical temperature of a substance is to heat it in a glass tube 1,20 under pressure until the meniscus between the liquid and vapor phase disappears, although other methods, especially for mixtures, have been used.13,14 However, when considering oil and gas reservoirs, it is more enlightening to consider a critical phenomenon that occurs when a mixture of oil and gas are compressed at a reservoir temperature until the meniscus disappears because the two phases become equal in composition. This conception, along with erroneous applications of the definition of the critical phenomena of a pure substance to that pure substance when it is part of a complex mixture, has caused confusion even among persons familiar with the classical theories. The purpose of this paper is to discuss the critical phenomena of pure substances and mixtures and to report experimental data on a mixture of

Jan 1, 1939

WHEN the new sulphide plant started to roll at Chuquicamata last July, we broached the matter of looking in on this historic event to Burr Wheeler, then executive vice president of Chile Exploration Co. (Chilex executive offices are housed with the parent company, Anaconda, at 25 Broadway which is 23 hours and 15 minutes closer to the AIME office than the mine, counting air and automobile travel). Mr. Wheeler was at Chuqui when they turned the first shovelful of earth, has an understandable pride and affection in the mine, and kindly offered to make all arrangements. As a guest of Chilex, physical exam, injections, police clearance, passport, and airline reservations on the crack Panagra airline are procured swiftly and almost painlessly. Winter clothes were advised by Mr. Wheeler and D. M. Dunbar, who is the former's assistant and a seasoned Chuqui-ite. Both of these gentlemen obviously prefer Chuqui climate, with 364 days of sunshine, 1 ½ -in. rainfall, rare atmosphere of 10,000 ft elevation, Christmas-time earthquakes, and howling winds through June and July to the vicissitudes of New York weather. Panagra's de luxe DC-6 noses in toward land at Antofagasta, Chile, the supply and embarkation port for Chuquicamata. The Coastal Range, completely barren of green, thrusts a spur far out into the Pacific creating a crescent-shaped and protected harbor at Antofagasta. Beach gives way to pampa, to hills, and the only variation in scenery is in topographic relief. Chilex's reception committee in the person of the alert and amiable Bob Condit, assistant port agent, takes care of everything: immigration, interviews by the local press, baggage, transportation, and introduction to Chilean cuisine. The drive up to Chuqui takes about three hours, on the only two lane highway in northern Chile; hard surfaced, with a few kilometers of repair work in progress. We were fortunate to make the trip with manager Charles Brinckerhoff, who arrived the same day at Antofagasta from the seat of government at Santiago where he goes frequently to keep in touch with the company's Santiago office.

Jan 1, 1952

By A. C. Stoddard

Early in the present century, prospect-ing was active in the area of the present Miami district. There were plenty of blue and green copper outcroppings, but very little ore of a grade that would stand shipping costs had been uncovered. Late in the first decade of the century, tunnels were driven into the north and south slopes of the Inspiration ridge, and two of them exposed disseminated copper sulphide ore. This was the original discovery of such ore on the ground of what eventually became the Inspiration Division of the consolidated company. By 1910 exploration of the ground area was well along and by 1911 underground development had been started. In the next few years a large tonnage of disseminated copper ore had been proven— sufficient to justify the expenditure of several million dollars in mine development and for mine equipment plus large sums for treatment plants. The mine and treatment plants were placed in production July 1, 1915. To Jan. I, 1945, there had been produced from the mines of the Inspiration Consoli-dated Copper Co., more than 106,000,000 tons of ore. Nearly all of this tonnage had been recovered by block caving. GeologIcal and EconomIc FActors Block caving is a mining system based on the fact that if a mass of rock has a sufficient number of fractures and planes of weakness the mass will disintegrate if the support of an area of sufficient size is taken away—that is, "undercut." If the material that caves away from the bottom of a block is drawn off the spalling is progressive. There is a limit to the speed of this spalling or caving action, which varies with the structure of the rock being caved. If the rock is drawn at a rate faster than the caving rate, and if this drawing is continued too long, a void may be created that could make a very dangerous condition if the area should drop as a block and force the air below the uncaved rock out through the raises and drifts. This can be a very destructive force. On the other hand, if the broken material is not drawn fast enough the swell of the material in place to broken material would pack the mass until it was almost solid again and could not be drawn without much blasting, or perhaps even partially undercutting again. Geologically therefore it would seem that any rock with seams and fractures would cave; but for block caving there should be enough seams and fractures in a limited area so that such an area will cave and produce a product that can be drawn safely, rapidly enough and at a cost justified by the value of the product being drawn. At the Inspiration the disseminated ores occur in two formations, the Pinal schist and the Schultze granite. There is no material difference in the grade of the ore formed in the schist and in the granite. The chief copper minerals are chalcocite, malachite, azurite and chrysocolla. Other copper minerals occur in limited quantity.

Jan 1, 1946

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By R. C. Thompson

The lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 450-ton operation. General Description The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1949

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

By H. H. Uhlig

In our study of the mechanism of and the prevention of corrosion in stainless steels, it was considered of fundamental importance to obtain knowledge of the surface structure of such alloys. If corrosion resistance is due to a self-healing oxide layer, which like a paint film protects the underlying metal, it would be obviously relevant were the effort made to make the film less permeable and more adherent; for example, the surface might be expected to respond to an anodizing process, which is found successful in increasing the film thickness and corrosion resistance of aluminum. However, if passivity and corrosion resistance of stainless steels are due to another cause, the attack of the problem would follow another path. One of the most effective techniques for studying passivity and corrosion tendency is the measurement of the electrochemical potential. Not only can one determine by potential measurements whether a metal is active or passive, but also one can determine the degree of passivity and rate of transformation of passivity with time. Chemical media that build up or destroy passivity when in contact with the steel can also be classified by potential measurements. Something can be learned, too, of the effect of alloy additions such as molybdenum to 18-8, known to decrease corrosion of the alloy in chloride solutions. A study of alloys in previous investigations has sometimes included data on the electrochemical potentials. Tammann and Sotterl measured the electrochenlical potentials of alloys of iron-molybdenum and iron-chromium and reperted the critical concentration of molybdenum or chromium at which passivity initiates. Strauss2 made similar measurements for the iron-chromium system. The electrochemical potential3 has also been used to indicate carbide precipitated 18-8. In 18-8, heat-treated to precipitate carbide, active metal exists at the region of the grain boundaries, contrasted with passive metal within the grains, the active metal accounting for a resultant active potential. Several

Jan 1, 1940

By J. L. Smith, A. L. Albee

This article presents a series of guidelines by which the geologist can evaluate the likelihood of surface faulting and its probable extent at any given site in Southern California and Nevada. The information is intended primarily for geologists concerned with establishing design criteria for proposed nuclear plants. The geologic problems involved in the location of a nuclear power plant are fundamentally no different from those for other types of installations. They fall into four main categories: foundation stability, landslides and slope stability, shaking due to earthquakes, and surface faulting. For problems in the first three categories the foundation engineer, the geologist, and the seismologist can provide criteria for plant location and design, and these problems can generally be economically handled by appropriate design measures for a project of the magnitude of a nuclear plant. However, problems in the last category — surface faulting — are more difficult to handle and require a unique evaluation. Accordingly, this paper will deal primarily with the problem of establishing design criteria for surface faulting, particularly as it affects nuclear facilities. A nuclear reactor is a power source that for greater safety is contained in a heavy, air-tight structure, just as gas, oil, water, and other power sources must be contained. Surface faulting is significant in that it may reduce the integrity of the containment by affecting critical exterior piping or by breaching of the containment. A similar significance exists relative to dams or tanks for the storage of water, gas, or oil, except that in these latter examples the breaching of the container automatically releases the fluids to do their damage. This is not necessarily the case with the rupture of a reactor containment structure because the function of the containment is totally protective, i.e., it is necessary only in the event that radioactive products are released from the reactor, and there are many other safeguards to pre- vent this release even if the containment is ruptured. At the present time, nuclear power plants must be located near large sources of water for cooling the steam generated. The construction of an industrial facility of any kind on the coast line is esthetically distasteful to most people since, unfortunately, there is not enough coast to fulfill all the needs and all the desires of all the people. In most cases where industrial facilities encroach on the lives of citizens, there is no mechanism other than zoning laws by which a person can effectively protest. But in the case of a nuclear facility, the public hearing required by the Atomic Energy Commission provides a forum for dissent, as in recent case histories, and the question of safety provides objectors with a weapon for fighting the construction of the plant. The nature of a public hearing for a nuclear plant is such that the prospective owner and operator must prove that there is no undue hazard, whereas the objectors need only demonstrate that there is a reasonable doubt. It is in this situation that geology becomes the Achilles Heel of nuclear power plant location. For his investigation, the geologist has natural exposures of rock at the ground surface and a limited number of trenches and drill holes to give him a fairly complete picture of the distribution of the various rock types. From the surficial data, he must infer three more dimensions — depth below the surface, past time, and future time. Unlike many problems faced by engineers, the geologist has only this one set of data from which to reach a conclusion — he is unable to reproduce the natural sequence of events in order to obtain another set of data for comparison. Hence, by the very deductive nature of a geologic conclusion, it is difficult to prove a geologic conclusion beyond a reasonable doubt even to other geologists — and perhaps one should say especially to other geologists because the experience and background of a geologist will strongly influence his conclusion, and no two geologists have exactly the same experience and training. The engineer and the public official would like the geologist to conclude that faulting cannot occur at a given site or to assign a numerical value to the probability of its occurrence — but no responsible geologist can do either of these things. Since government officials and others must make decisions that affect the public safety, it would seem that the geologic profession must attempt to establish criteria and

Jan 1, 1968

By J. Mazia, H. Rosenthal

An investigation has been made of residual stress in the head and body of caliber 0.30 cartridge cases. The head was divided into four ring-lie sections which were cut off by a jeweler's saw. Spring-out was measured after a radial cut had relieved the circumferential bending moment. The residual stress corresponding to the observed spring-out was calculated by formulas in which the computed stress was a function of wall thickness. All rings sprang open, indicating compressive stress on the inner wall and tensile stress on the outer wall. The production stress-relief anneal of 475 F. for 45 min. reduced the stress to almost half. The priming and crimping operation, however, again raised the stress, especially in the flange section. The dect of stress-relief heat treatments on residual stresses in the body of caliber 0.30 cartridge cases was investigated by the split-ring method. Although this method did not reveal any large stresses in the body, the neck before mouth anneal was found to contain a computed stress of 30,000 psi. at the surface. This value was reduced to 15,000 psi. in 120, 30, and 15 min. at 400, 475, and 500 F., respectively.

Jan 1, 1945

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained the isothermal growth of the phase follows a simple parabolic equation: X2 = kt [I] where X is the thickness of the alloy layer, k the reaction rate constant, and t the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such. a plot has been con¬sidered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation k = Ae-Q/RT [2] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative, thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase .4 The reaction layers tend to have a

Jan 1, 1942

By Charles Himrod

IN presenting this paper it is not intended to enter into any discussion of the theory of the blast-furnace, but simply to give the results of a number of determinations of CO and CO2 in furnace gases, and some conclusions arrived at, and the result of an experiment made in hopes of increasing the production of CO2. In the first table, on page 198, is given the averages of a number of analyses of gases of different furnaces, and in the second, of two stacks of different sizes under varying circumstances. The conclusions arrived at as to what influences the production of CO2 are as follows: 1st. Kind of fuel. Bituminous coal not permitting the formation of as much CO2 as coke. 2d. Kind of ores. Rolling-mill cinder being much less favorable to formation of CO2 than hematite ores, magnetites probably less than hematites, but more than cinder. 3d. Length of time of contact of gases with ore. Small furnaces and too rapid driving both waste fuel by not allowing enough time for conversion of CO into CO2. 4th. The temperature of blast. The hotter the greater the quantity of CO2. 5th. Regularity of passage of stock through the furnace. The hanging and dropping of the stock, however slight, seems to pack it more solidly in the hearth, increases the resistance to the blast, and decreases the quantity of CO,. These are the most common causes noticed which influence the production of CO2, unless we except the one that might be considered the greatest of all, the one that has spoiled so many tons of iron, and the amiability of so many furnacemen, the one most dreaded, the great unknown. It would seem a self-evident proposition that the better the contact of the gases with the ore and the less with the fuel, the greater would be the amount of CO2 produced. To prolong the contact of gas with the ore furnaces are enlarged with advantage, and pains are taken to charge the stock in such a, manner as will best promote it. Still, with furnaces of most approved construction and most skilful manipulation, the gases leave the furnace so rich in CO, that not half the heating power of the fuel is obtained, and the highest

Jan 1, 1877

By D. M. Davidson

THE drill sampling and evaluation of the Piney River ilmenite property was carried out during the early part of 1944 by E. J. Longyear Co., using the company's standard core-drill outfits to complete 44 holes to an average depth of 110 ft., from which were collected 1100 samples. The Piney River ilmenite-apatite lode is 25 miles north of Lynchburg, in Nelson and Amherst Counties, Virginia (Fig. I). Its elevation is about 900 ft. above sea level and it lies in the old pre-Cambrian complex of crystalline rocks that make up the Piedmont physiographic province lying east of the Blue Ridge Mountains. The terrain is gently rolling and well watered, and is drained by the Piney and Tye Rivers, which are tributary to the James. GEOLOGY The Piney River ore body comprises the upper, weathered part of a tabular basic rock, which occurs in a large area of granite-gneiss. The section containing profitable ore is about 3000 ft. long. It is separated naturally by thinning, into northeastern and southwestern segments with widths of 300 and 100 ft. respectively. The dip averages 45° southeast but steepens locally (Figs. 2 and 3). The unaltered rock is an even, granular mixture of feldspar, ilmenite, and apatite, to which Watson1 gave the name Nelsonite. The decomposed ore body, which is now being exploited by open cut, is a yellowish clay material in which black ilmenite and glassy apatite are the only conspicuous minerals. An economically important structural feature of the deposit is a banding of minerals coinciding with the dip and strike of the dike. This is more promounced in the footwall of the northeastern part of the intrusive, where there is also a higher than average concentration of ilmenite. According to Watson,1 the Ti02 content of the Nelsonites of this region ranges from 10 to 42 per cent, while P205 varies from 4 to 15 per cent. It is inexpedient at present to disclose exact metal content of the Piney River ore body; suffice it to say that the average tenor lies well within the extremes noted by Watson. SAMPLING METHODS AND PROCEDURE During a preliminary inspection of the ore body, Longyear engineers surmised that because of its soft, clayey character, drill sampling would yield little core, therefore they made all possible preparations to procure accurate samples of the drill cuttings, or sludge. The first requisite in obtaining representative drill cuttings is to secure their full recovery. Only under certain conditions, and by employing a most careful and rigid sampling technique, is this possible. There must be no loss of the water circulating in the hole, and the velocity

Jan 1, 1946

By J. S. Diller

In 1827, chromite was discovered near Baltimore by Isaac Tyson, Jr., who initiated the mining of chrome ore an:! later (1845) .the manufacture of chromium compounds in this country. From 1828 to about 1860 the United States, supplanting Russia, supplied chromite for most of the world. Chrome deposits were found also in California, and the Tyson Company shipped ore to Philadelphia by way of Cape Horn. In 1848, J. Lawrence Smith, an American in the employ of the Porte, discovered large bodies of chromite in Asia Minor. They were developed in 1865 and became the chief source of the world's supply for a number of years. The discovery of the large high-grade bodies in New Caledonia, and later in Rhodesia, with other foreign sources, gives at present an abundant supply for all demands. For a number of years before the great war, the United States produced only a few hundred tons of chromite annually, for local use, but during the war the demand for domestic ore resulted in a production of more than 82,000 long tons of crude ore in 1918, and it was demonstrated that the United States has reserve deposits equal to a war demand of several years' duration. Now that the war is over, the country is conserving its domestic supplies by employing higher-grade but cheaper ore from foreign countries. ChromiUm-bearing Minerals Oxides: Chromite-—chromic iron ore................ FeO.Cr2O3 Picotite—chromic iron ore................. (MgFe)O.(Al,Cr) Chromates: Crocoite—lead chromate................... PbCrO4 Phoenicochroite—basic lead ohromite........ 3PbO.2CrO3 Vauquelinite—phospho-chromate of lead..... 2(PbCu)CrOd.(PbCu)3P2O8 Sulfates: Redingtonite—hydrous chromium sulfate.... Knoxvillitel—hydrous basic sulfate of chromium.............................. Daubreelite-—iron-chromium sulfide (known in meteorites only)...................... FeS.Cr2S3

Jan 1, 1920

By Earl Bardwell

THE determination of suitable and safe annealing temperatures is one of the most important problems arising in the operation of a copper rolling mill. Certain of the larger mills have worked this problem out for themselves and in these mills the operation has become more or less standardized. In some of the mills pyrometers are used to measure the temperature of the annealing furnaces and careful watch is kept to see that overheating does not take place. In a considerable number of the mills, however, dependence is placed entirely on the judgment of the operator. The almost total lack of literature bearing on this subject seems sufficient warrant for the publication of this paper. The discussion of this subject naturally divides itself into two parts: (1) The effect of annealing temperature on physical properties; and (2) changes in the microstructure of refined copper due to cold rolling and annealing. I. THE EFFECT OF ANNEALING TEMPERATURE ON PHYSICAL PROPERTIES For the purpose of investigating this phase of the subject six test bars were selected, varying in oxygen content between the limits of 0.036 and 0.070 per cent. The chemical composition of each of these test bars was as follows:

Jan 8, 1914