Search Documents

By AIME AIME

THE following paragraphs comprise such information as the Secretary has been able to obtain concerning the members and associates whose deaths have been reported. Further particulars or corrections of errors, and biographical data concerning deceased members or associates not already noticed in this way, are solicited. [SECRETARY'S NOTE.-All of these notices have been revised, and some of then have been more or less completely prepared, by me. To those which contain more particularly the expression of my personal feeling, my initials have been appended. The labor of preparing or editing these paragraphs has been in many respects both welcome and interesting, on the one hand, and sorrowful, on the other. In going through the list, I have repeatedly felt like one who, visiting the Morgue, suddenly comes upon the pale face of a dear friend, of whose death lie was not aware ; and, even when this fact was known to me, the work of recording it has brought upon me a flood of recollections, almost preventing the discharge of that official duty. The list for 1907 seems to me to he peculiarly sad, comprising, as it does, so many sudden deaths by violence or accident, so many veterans, removed too soon, and so many young men whose early departure impoverishes the future, even more than the present. Probably, this feeling on my part is largely due to the circumstance that the increased membership of the Institute necessarily in¬volves an increase of the annual death-list. Probably, also, it is connected with the circumstance that during the first years of the history of the Institute-say from 1871 to 1880-it was joined by men of all ages, and that the death-rate is consequently now above the average which would result from the normal annual addition, principally of young men. And finally, I must admit that, as one of the original members of the Institute, and practically connected with it for nearly thirty-seven years as Acting President, President or Secretary, I am peculiarly impressed and depressed by the successive deaths of those who were my associates in the years of its early struggles and triumphs. I do not wish to inflict upon my younger colleagues the melancholy reflections of an increasingly lonesome old man. In fact, my prevailing mood concerning the Institute is not at all melancholy, but triumphant and hopeful. If I may be permitted to preach at all, I would enforce, from the texts given below, a moral which many of them declare so forcibly as to preclude the necessity of expository enforcements-namely, the duty of every one of us, old or young, to give to his brethren, as he goes along, and without waiting for some future occasion for a comprehensive and monumental contribution to technical literature, the results of his observation and experience. When I look at this list of names, my personal sorrow over many of them is drowned in my professional reflection as to each and all-How much has died with

Jan 1, 1908

By Prince Lazarovich, Hrebelianovich

I WAS asked by the chairman of one of the Sessions on Employment Problems to talk about the viewpoint of the foreign workingman. I am not a workingman. I have never done what a work-hand might call an honest day's labor; that is, I have never been in a factory or manufacturing plant or in a mine, though in truth, hard work and I are well acquainted. I was a soldier, am an engineer, have long been actively interested in the most important waterway construction in the near East, have served politics and diplomacy, written books and lectured at universities. My knowledge of the foreign workingman in this country comes from the fact that my own compatriots here at various times came to me and appealed for advice and help, and last year I was asked by the employment manager of a corporation to undertake a welfare job at one of their plants. I went out, saw the plant, talked with the superintendent and outlined certain of my ideas which he personally heartily approved, but which did not find favor with those higher up. I approach the subject of the foreign workman's point of view with the understanding that the industrial employer's effort is for the maximum of efficiency. I am conversant with labor conditions abroad both in industry and agriculture. What I have learned of industrial conditions in America as they affect the foreign immigrant has been chiefly gathered from the cases referred to of foreign workmen who from time to time have come to me with their troubles. In the course of those investigations, in order to give whatever help or advice was possible, I have been impressed with the fact that the great United States industries evidently had- pot yet sufficiently recognized the value of studying the conditions of the workingman in the lands of his origin across the seas. A careful study of that which could be called the moral element in connection with its foreign labor would give industry a knowledge of the man's reason for coming, what' grievances he brings with him, his hopes for a future, and the peculiar character of his capacities. The employer would thereby be enabled to meet the man, to be helpful to him, to aid him and at the same time promote industrial efficiency, inasmuch as a workman who believes that he is being dealt with humanly and squarely is contented and satisfied and will give willingly, and even with pride, the best that is in him; justice and a fair deal is all the man wants.

Jan 4, 1918

By George Otis Smith

A YEAR ago, ,at the Institute's dinner, I closed my A remarks with the words: "The scientist devotes his life to the advancement of learning; the engineer gives his to the advancement of living." May 1 begin tonight where I left off then and speak first of the distinction between science and engineering? This difference is a difference both in purpose and in method: it is the sharp contrast between theory and practice; it marks the broad gap between dream and attainment. Sometimes it happens that the investigator is also the builder and applies what he discovers, yet the distinction between science and engineering serves to point out the broad dependence of the engineer upon his brother the scientist. You remember .the old - saying that "where there is no vision the people perish" translate this into modern experience and we may say that "where there is no science, the engineer fails."

Jan 1, 1929

By J. Szekely, J. W. Evans

A formulation is given for radiant heat loss from the surface of molten steel held in a ladle and numerical solutions are presented for the resultant integrodif-ferential equations. The results are shown on plots of the net rate of heat loss against time, with the geometlry, emissivities, thermal properties of the walls, and Preheat as parameters. It was found that the rate of the vadiant heat loss from the exposed metal surface was comparable to the conductive losses from the Portion of the metal in direct contact with the walls. The radiant heat loss was markedly affected by the geometry and by the thermal properties of the walls the net radiant heat loss from the steel could be drastically reduced by providing a top cover and also by the provision of preheat. The results of this work are thought to be relevant to heat loss calculatious concerned with vacuum degassing and with operatzons in which molten metals are held in ladles. WhEN molten steel is held or transferred in ladles heat losses inevitably occur. The accurate assessment of these heat losses is of importance in process design considerations, as the temperature of the metal may have to meet rigid specifications in certain stages of the processing sequence. As shown in Fig. 1, the principal mechanisms responsible for heat loss are: i) Conduction into the walls and ii) Thermal radation from the top metal surface (possibly augmented by natural convection) The conductive heat loss may be readily calculated as much information is available in the literature on both the general theory1'' and on its particular applications to ladle heat loss calculations. Evaluation of the radiant component of the heat loss is less straight-forward. In two recent papers it has been shown that the presence of a slag layer 2 to 3 in. thick would prevent any significant heat loss for periods up to an hour,5'" however, should bare metal be exposed, constituting the radiant surface, substantial heat losses could occur. This latter case is of considerable practical interest in various degassing operations and in the vacuum processing of certain specialty steels, where the top surface of the metal is not covered by a protective slag layer. Under these conditions a substantial radiant flux is emitted by the top metal surface; part of this flux leaves the system, part of it falls in the ladle walls. The radiant flux incident on the ladle walls is in part absorbed and conducted away, and in part reflected and re radiated. The purpose of the paper is to present a general formulation of the problem, the resultant solution of which should enable computation of the net radiant heat loss from the metal surface. The principal variables, the effect of which will be investigated, include initial metal temperature, geometry, thermal and radiative properties of the wall, and various modes of preheat. FORMULATION Consider a cylindrical enclosure, shown in Fig. 2, with a diameter D, height H, and wall thickness W, the cover at the top of the cylinder having a wall thickness L. If the temperature of the base (representing the top surface of the metal) is kept constant, say, Tb, the problem is to calculate the net rate of heat loss from the base as a function of time, geometry, the initial temperature distribution, and the thermal properties of the system. As customary, the formulation will consist of the mathematical statement of the conservation of thermal energy within the system.

Jan 1, 1970

By Sydney H. Ball

A QUARTER of a century ago, a pessimistic Belgian financier in conversation with the founder of the Belgian Congo, that great ruler, Leopold II, emphasized the danger to the colony should the synthesis of rubber be discovered. The king replied, "I do not worry. The Congo has had its ivory period; it now has its rubber period. Tomorrow it will have that of its mineral wealth; eventually that of agricultural products." That "tomorrow" arrived some twenty years ago. Through her mines the Belgian Congo has survived the present depression, and her mines for the next decade will safeguard her. The Congo, in turn. is the surest foundation industrially and financially of Belgium itself. In few, if any, political units is mining as dominant as in the Belgian Congo. In 1930, 1931 and 1932 mineral products represented respectively 67.9 per cent. 70.5 per cent and 59.3 per cent, of the total exports. In 1933 for each white person in the colony, there was produced about $1,675 worth of gold, diamonds, copper, tin ore and minor mineral products and in 1930 the per capita production, notwithstanding the larger population, was almost $2,000.

Jan 1, 1934

By Frank Haas

THE public generally has-become aware that there is something wrong with the coal industry and a clamor has arisen for an explanation if not a remedy for this disorder. It is only reasonable that this Institute be looked to for a diagnosis to show the way for some other .agency to prepare the patient for prescription or operation. The subject is extensive, widely diversified, and beyond the efforts of an individual to cover completely; one of the objects of this paper is the initiating of a symposium on the non- technical factors essential to an understanding of the bituminous coal industry. The present condition of the coal industry cannot be described in a few words but, in effect, it resolves itself into a simple statement: The average coal operator is losing money notwithstanding a firm conviction on the part of the consumer that he pays too much for his coal. Without enumerating the many and varied. factors which contribute to this condition, this paper will be devoted to the interrelation of taxation and ownership of coal and its effect on finance

Jan 1, 1930

By RICHARD MAIZE

IN this critical period of our history, the coal industry of the nation, faced with many obstacles, performed its work safely during the first ten months of 1943. Thousands of the younger mine workers were inducted into the armed forces of our country and in many instances their jobs have been filled by others without much if any experience and training. This situation alone would seem to be sufficient to interfere with the safe and orderly operation of the industry but the Government's demand for a substantial increase in coal tonnage over that produced in normal times introduced a hazard which always accompanies speed, regardless of the skill of the worker.

Jan 1, 1944

By JAMES SCULLY

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That subject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public attention has focussed as never before on the subject of commodity prices. To advocate stabilizing commodity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent fell by 20 per cent. Thus a price that appears stable in dollars, rose in terms of pounds sterling and fell in terms of marks and yen. Had this result been achieved as a consequence of an international effort to stabilize prices, an American would have said the effort was successful. An Englishman would have said it had failed to prevent a price rise. And a German or a Japanese consumer would have been happy to have covered his copper needs at a lower cost in terms of his own currency.

Jan 1, 1978

By LESTER H. WOOLSEY

IT IS doubtful whether anything new can be said upon this subject and, therefore, it is with considerable hesitation that l prepare this paper. On account of my recent connection with the Department of State as its law- officer, perhaps I will be pardoned if I discuss this subject briefly from the point of view of that branch of the Government. , I cannot, of course, speak for that department, since I have-no connection with it at-present, but it may be helpful if I set down certain* of the factors which in my opinion and from my experience have a bearing on this international problem. With oil-burning ships, motor vessels, motor vehicles, airplanes-all consuming, astonishing quantities of petroleum or petroleum products; with the United States having within its borders only 12 per cent. of the petroleum resources of the world, and consuming about 70 per cent. of the world's output; with the more enterprising nations wide awake to the necessity ; of obtaining and preserving as large a share as possible of the oil resources extant ; the 'problem is peculiarly and in a, very practical sense an international one.

Jan 1, 1921

By John A. Prof. Church

ONE of the most striking phenomena connected with the mines on the Comstock lode is the extreme heat encountered in the lower levels. This heat is not due to the burning of candles, heat of the men, and decomposition of timbers, all intensified by bad ventilation, as was the case nearer the surface. It proceeds from the rock, which maintains constantly a temperature very much higher than the average of the atmosphere in Nevada. The heat of these mines is a matter of more than usual interest, for they are the only hot ones now worked in the United States, and both in the present temperature encountered and in the increase which is to be expected as greater depths are reached, they appear to surpass any foreign mines of which we have a record. Hot mines are known also in other countries, as in the tin and copper lodes of Wales, where one of the veins worked by the United Mines is known as the hot lode. It has springs which discharge water at a temperature of 116° Fahrenheit, the depth being 220 fathoms, or 1320 feet. The heat of the air in these workings is given at 100° to 113° Fahrenheit. The air is bad, and the heat in the drifts seems to be traceable to defective ventilation rather than to the real necessities of the case. Air is supplied through a small pipe, and is drawn from a place where the temperature is 95° Fahrenheit. Under such circumstances it is not surprising to read that in this hot mine the air is hotter than the rock, a state of things which I have never observed in the Comstock. Other mines have been reported to the British Coal Committee as having temperatures of 106° Fahrenheit and thereabouts, but the only positive comparisons that are available at this writing are the following, all from Cornish mines * Read by permission of Lieut. Geo. M. Wheeler, Corps of Enginerrs, U. S. Arm J, in charge of U. S. Geographical and Geological Surveys, west of the 100th meridian.

Jan 1, 1879

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By George Mixter

MINING, in contrast to manufacturing, deals with a wasting asset. That which is taken out of the ground is gone, the property is depleted to that extent, and will eventually become exhausted of profitable ore. So the life of a mining company is dependent upon the ability of its management to develop improved methods to permit extraction at a profit of the lower-grade ores which remain, to extend by intelligent exploration the limits of its known ore bodies, and to find and acquire new properties to take the place of those that, for one reason or another, are no longer operated. Its history is a story of constant change, of the working out of properties here and the acquisition and development of properties there, to maintain the vitality of the whole. It is a story of estimating with the tools and the knowledge available the location and extent of hidden ore bodies and of devising the means of extracting

Jan 1, 1948

AGGLOMERATION U.S. 4,067,727 - In the sintering of a charge of iron oxide ore, a fuel and a flux on a travelling grate machine, the dust problem is minimized by providing a plurality of cooling zones and by directing heated dust-laden air from a first cooling zone to the sintering zone wherein the dust is filtered from the air by the material being sintered. Air from a further cooling zone can be exhausted directly to the atmosphere. Dust removal in the cooling zone is improved by using a purging zone in which higher pressure air agitates the dust in the sintered material. This patent is a division of U.S. Patent No. 3,973,762, dated Aug. 10, 1976. F. Cappel, assigned to Dravo Corp. Jan. 10, 1978. 6 pp. (75-5). Filed: 4-1-76 (672,748).

Jan 1, 1979

By D. R. Mitchell

MEETING for the thirteenth time in New York as part of the five-ring circus known as the Annual Meeting A.I.M.E., the Coal Division experienced a wartime boom in attendance. Technical sessions were crowded and whereas 65 seats were set up for the annual luncheon meeting of the Division over 100 members showed up, many of whom had to be fed elsewhere. Possibly the Coal Division should adopt "13" as its lucky number. Discussions at technical sessions, formal and informal, were lively. Those papers containing material directly concerned with the war, or containing information that might be usable for war industries, were enthusiastically received. Some criticism was made in regard to the present method of handling discussions and it was suggested that better success would be had in getting discussions in the record by the use of hired reporters. This is being considered by the executive committee of the Coal Division.

Jan 1, 1943

By S. W. Poole, J. A. Rosa

The object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition of the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. Steelmaking Data Melt.—The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping tempera- ture, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.—Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.—Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 1/2-in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. Sectioning and Preparation for Sulphur Printing Because of previous favorable experience in sectioning ingots up to 21 1/2 in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. 2 and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200F.

Jan 1, 1945

By D. R. Parrish, F. F. Craig

In some respects, forward combustion (alias: fie-flooding, underground combustion, in-situ combustion, dry combustion) is an efficient oil recovery method. For example, its displacement efficiency (as much as 95 percent in reservoirs with high porosity and high oil saturation) is good. In its use of heat, however, forward combustion is grossly inefficient. Most of the heat generated during forward combustion is wasted. About one-fifth of the heat is picked up by the incoming air and re-used (regenerated); the remainder is left behind the combustion zone and ultimately is lost. Compressed air is expensive, and heat generated from compressed air via underground combustion is too valuable to be thrown away. Improvement is needed. Since the early 1950's, improvements in forward combustion by addition of water injection have been discussed, particularly in the patent literature, with increasing frequency.'-'' These concepts are based on the fact that relatively inexpensive water can be used to pick up much of the heat that is ordinarily wasted during forward combustion, and transport it forward to a more useful place, thereby reducing the amount of air required to move a heat front through the reservoir. Several approaches have been proposed. Merriam and Squires1 taught that a combustible (fuel) gas should be injected along with the air and water. This, however, would give at least a tendency toward reverse combustion instead of forward combustion, and would reduce the velocity of the heat bank, defeating the primary purpose of the water injection. Pelzer2 described primarily a batchwise method of forward combustion and water flooding. He advocated burning part way through a reservoir with forward combustion, then switching from air to water injection alone to push the heat toward the producing wells. Though possible, this method has serious disadvantages, the major one being that, by the time water injection is started, much of the heat has been irretrievably lost to the overlying and underlying formations. We have described what is considered a practical Combination Of Forward Combustion And Water-flooding (COFCAW).3,4 Air and water are injected simultaneously (or alternately) after a small heat bank has been formed by forward combustion. Some of the injected fluid fills up the region behind the heat bank; the rest enters the heat bank. Upon encountering heated rock, the water is converted into steam, which then flows ahead of the combustion zone and displaces much of the oil in place. Only enough air is injected to provide heat for vaporization of the water and to compensate for reservoir heat losses. Since the size of the heat bank is minimized, heat losses also are minimized. Because of more efficient oil displacement ahead of the combustion zone, fuel consumption is reduced. Too, unlike a forward combustion zone that cannot move until all fuel at a point has been consumed, COFCAW leaves some

Jan 1, 1970

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By J. A. Pusateri, M. A. Orehoski, N. R. Arant

Plant studies on commercial-size ingots and laboratory experiments with induction furnace heats have demonstrated that the major source of ingot cracks is associated with two conditions arising during top-pouring practice: 1—solidification during pouring, and 2—turbulence created by the impact of the stream. Methods of controlling the two factors were effective in eliminating or significantly reducing ingot cracks. BECAUSE the process of removing surface defects from hot-rolled product is so costly, the steel industry is striving constantly to develop methods of preventing, or at least decreasing, the occurrence of surface defects. Investigations have revealed steel-making and processing variables related to major surface defects, and controlling these variables has led to improvements in surface quality. However, the fundamental causes of major surface defects, such as ingot cracks, have not been determined; consequently such defects persist. At the Research and Development Laboratory of the United States Steel Corp. in Pittsburgh, a seam research program was initiated to determine the fundamental causes of certain major defects. As a part of the program, ingot cracks in killed, finegrained C1020 steel were selected for study. A cost survey indicated that, of the steels produced in sizable tonnages, carbon steels in the range of 0.18 to 0.23 pct C content require the most conditioning. Since this is particularly true of C1020, any im-provement of surface quality that might be effected from the study would be beneficial. Also, since the frequency of ingot cracks is exceedingly high for this grade, the steel would provide an excellent opportunity for a thorough study of the ingot-crack-ing problem. Why steels in this carbon range tend to exhibit more ingot cracks than do other steels was not considered in the investigation; the mechanism of ingot-crack formation was of paramount importance. Also, only the top-pouring practice was considered in the investigation, because this pouring procedure is used more extensively than others. In this study, ingot cracks are defined. as deep surface defects that sometimes are observed in an ingot prior to rolling but usually are observed during the initial stages of rolling on the primary mills. These defects may occur at any angle to the rolling direction but are most prominent in the transverse or nearly transverse direction. The appearance of ingot cracks on the rolled product varies with respect to their angle of formation and with the extent of rolling after their first occurrence. Ingot cracks are also termed "deep seams," "arrowheads," "irregular cracks," and "transverse cracks." Fig. 1 shows ingot cracks in a rolled bloom. This report summarizes: l—the exploratory investigation of commercial-size ingots; 2—the labor-atory investigations related to determining the source of ingot cracks and developing corrective methods; and 3—the plant evaluations of laboratory methods of decreasing ingot cracks. Exploration of lngot Cracks in Commercial Ingots Materials and Experimental Work: At the Du-quesne Works of the United States Steel Corp., five heats of killed, fine-grained C1020 steel were selected for the exploratory phase of the seam-research program. The heats were made by open-hearth practices that are considered most conducive to good surface quality. They were top-poured into 22x25 in. big-end-up hot-topped molds. One as-cast ingot and four other ingots rolled to the following cross-sectional sizes were set aside from each heat: 16x20 in.; 9 1/2x10 in.; 5x5 in.; and 2x2 in. The processing of the heats, from the time of charging in the open hearth furnaces to the end of the rolling operation on the primary mill, was observed carefully and recorded. The cast ingot and the four rolled ingots from each heat were examined for surface defects. The cast ingots were split longitudinally near the vertical center plane to expose the ingot structure beneath badly cracked regions. Also, a series of transverse sections was cut at about 1 in. intervals in a badly cracked area of one ingot. All sections were ground, polished, examined by sulphur printing and deep etching, and photographed. The rolled ingots

Jan 1, 1955

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938

By John E. Greenawalt

In view of the increasing importance of sintering in the beneficiation of iron ores preparatory to their reduction in the blast furnace, the writer believes the time is opportune for an up-to-date, though brief, discussion of the general principles of sintering, as well as a discussion of some of the recent improvements and mechanical developments that have been achieved in this industry, its present trend and future possibilities. Sintering may be defined as the agglomeration of fine mineral particles into a porous mass by incipient fusion caused by heat produced by combustion within the mass itself. Its first successful application, in connection with the treatment of lead sulphide ores, was known as blast roasting. In this process the lead ore was given a preliminary roasting in a reverber-atory furnace, then the incandescent mass was placed in a pot with a grate and an updraft was applied. It was soon discovered that much better results were obtained by cooling the ore, moistening it, and placing it upon an incandescent layer of fuel previously placed upon a grate, and then applying the updraft blast of air until the charge was converted into a more or less agglomerated mass. The fuel was sulphur and the process one of desulphurization, which was the principal result desired. The application of downdraft to blast roasting brought about tremendous results; the principal one of which was that an air blast of high pressure could be passed through a layer of ore deposited on a grate, or on a grate covered by a layer of coarse porous material, without disturbing the particles of which the layer is composed. The air current is compelled to filter through the pores of the charge, whereas if the same pressure applied to the top surface of the charge with downdraft were applied to the bottom of the charge with updraft, the charge would be completely blow11 off the grate. Another result of reversing the draft was that a flame could readily be applied to the top surface of the charge for igniting purposes. Broadly speaking, sintering is an oxidizing or burning process, therefore the volume of air passing through the charge is the all-important factor. The air must pass through with sufficient rapidity to produce the necessary heat, and if sufficiently rapid the combustiorl will take place

Jan 1, 1938