Search Documents

By Ole Singstad

THE legislatures of New York and New Jersey, determined in 1919 that a vehicular tunnel should be built under the Hudson River. On July 1, 1919, an engineering staff was organized with the late Clifford M. Holland as chief engineer, and this staff was given a number of problems to solve, such as location, size, type of tunnel, method of construction, method of ventilation and cost. After a period of preliminary investigations and studies it was decided to build the tunnel at Canal St., New York, connecting 12th St., Jersey City. This is the center of the heaviest traffic across the Hudson River. It was also decided to build two tunnels-one for west-bound traffic and one for east-bound traffic-the tunnels to be of cast iron, built up of segments and bolted together, each tunnel to have a roadway 20 ft. wide and a clear heat room of 13 ft., 6 in. This is to provide for two lines of vehicles in each direction. The tunnels have an exterior diameter of 29 ft., 6 in. The interior lining is of concrete, the sidewalls tiled with a vitreous white tile and the roadways paved with granite block. The entrances and exits at both ends are separated by two blocks so as to reduce traffic congestion.

Jan 8, 1926

By H. J. Beach

This paper describes the properties and uses of cementitious mixtures containing 10 to 20 per cent bentonite and 2 per cent or more sodium chloride. Salt additions improve bentonite cement by increasing early strength and stabilizing viscosity without changing thickening time. The volume yield of cement is increased 20 per cent or more without lowered early strength. The unique properties of salt in this type of system make savings of more than 10 per cent possible where light-weight, low-strength cementitious material is adequate to fill behind pipe. The density range of these mixtures is 12 to 13 1b/gal and the filtration rates are medium-low, aiding the placement of long columns in primary cementing. Where available, sea water is an ideal salt source in preparing these slurries. INTRODUCTION Accelerators increase the rate of cement hydration. In speeding reaction with water, they can affect cement performance by reducing thickening time and increasing early strength after set. Accelerators that cause both effects can be considered "total", and those which produce only one effect can be called "partial". Materials that act conversely to accelerators are retarders. and they also can be total or partial. Partial retarders. make high-temperature cementing possible by prolonging thickening time while impairing early strength only slightly. Most known accelerators are total. A useful partial accelerator would increase strength without altering thickening time. This report concerns material combinations in which a normally total accelerator exerts unique partial properties. Utilizing these limited effects improves bentonite cement. SEPARATE EFFECTS OF SODIUM CHLORIDE AND BENTONITE ON CEMENT Sodium chloride and calcium chloride are commonly used in cement, and at low concentrations their effects are similar. Ludwig1 studied sodium chloride in API Class A and Class E cements.' Figs. 1 and 2 sum- marize his data taken at 140°F on slurry pumpability and early strength. Normal water-to-cement ratios are 0.46 and 0.40, respectively, for Class A and Class E cements. At saturation the salt content is 12 to 14 per cent of the weight of cement solids. The illustrations, therefore, cover the range of salt solubility in the mixing water. The data show that sodium chloride is a total accelerator of the Class E cement studied over the range of solubility. It is total in Class A cement to 6 per cent. Above this concentration salt becomes a retarder— partial from 6 to 10 per cent and total above. These results are general for different brands of Class A cement, although the shift from acceleration to retardation may occur at different salt concentrations for different temperatures. The results are specific for the Class E brand studied. In discussing his data, the investigator emphasized that different Class E cements might respond erratically to salt, depending on the brand chosen. Morgan and Dumbauld3 escribe the properties of bentonite cement in a paper that is a standard reference in using these systems. Bentonite functions in cement as an enabling agent; each bentonite addition equal to 1 per cent of the weight of dry cement makes possible the further addition of 4.5 per cent water.' Thus, 10 per cent bentonite in Class A cement, normally slurried neat with 46 per cent water, enables the slurry to contain another 45 per cent before settling. Water is one of the lightest and cheapest cement extenders; it reduces density and cost. Bentonite cements produce uniform slurries having low susceptibility to solids separation. After set, they offer low resistance to perforation.

By M. C. Flemings, F. R. Mollard

Conditions necessary for plane front growth of two-piwse solids from a single-phase melt are discussed. Alloys consideved are those from a simple binary system containing a eutectic, but are not, in general, of eutectic cornposition. It is concluded that: 1) plane front solzdification is favored by low growth rate, steep thermal gradient, and essential absence of convection; and 2) for steady-state solidification, the structure should resemble that of directionally solidified eutectics (lamellar, rodlike). Factors affecting THERE are many materials, including metals, available today with strengths in excess of 10' psi when in whisker or fiber form. The challenge facing those interested in practical application of such materials has been, and remains, the economic production and incorporation of the whiskers or fibers into useful engineering composites. solute redistribution along the growth direction are described quantitatively, by numerical solution of the diffusion equation. Effects of variations in growtlz rate on average composition of the solidifying composite are significant. For alloys not too close to a single-phase region, the initial transient at constant gvowth velocity is the order of D/R where D is diffusion coefficient in the liquid and R is interface velocity. Composites consisting of the reinforcing phase within a metallic matrix have excited particular interest in recent years because of their potential for high strength at elevated temperature and for resistance to brittle fracture. Techniques employed to incorporate the whiskers or fibers in the metallic phase have included 1) liquid metal infiltration, 2) solid or liquid phase sintering, and 3) direct growth of composites from the melt, of rodlike or lamellar morphology, by directional solidification of eutectic alloys. Two recent books"2 have reviewed the status of this growing field. Concerning the last method, growth of eutectics, it has been shown that the reinforcing phase (e.g., rods)

Jan 1, 1968

By M. R. J. Wyllie, P. F. Southwick

The importance of the so-called "dirty sand" or "conductive solids" problem in electric log interpretation was first stressed in a paper presented in 1949. Since that time the problem has been generally recognized as a most serious one. Several research papers bearing on the theory of the effects of clay contaminants on reservoir rock resistivities have appeared. These papers, while contributing to the theory of the problem, have not offered any practical solution. In the present paper an experimental investigation has been made of the effects of ion-exchange materials on the electrical properties of natural and synthetic porous media. The method used to make synthetic dirty sands is entirely novel and has proved a valuable guide to a better understanding of the properties of dirty sands generally. The effects of ion-exchange materials on both the resistivity and self potential (S.P.) logs have been examined. From the data obtained it has been possible to formulate a simple, practical method whereby electrical logs of dirty sands can be qualitatively interpreted. The method is in all essentials identical to that presently in use for interpreting clean sands. New light has also been thrown on the significance of the term formation factor when it is applied to dirty sands. In 1949 a paper was presented1 which showed that the presence of so-called "conductive solids" introduced considerable complexities into the analysis of the resistivities of dirty sands, i.e., permeable formations containing clay. The reduction of the self potential (S.P.) resulting from the presence of interlaminated shale or interstitial clay in permeable formations has been discussed by Doll.2,3 Noteworthy papers which dilate further upon the effects of shale and clay on the resistivity of permeable formations are those of deWitte,4,5 Berg,6 Wyllie,7 and most recently, Winsauer and McCardell.8 The last authors have endeavored to elucidate the chemistry of the resistivity phenomena in dirty sands in terms of an adsorption hypothesis. Specifically, they attribute the electrolytic conductivity of shales and clays within a permeable formation to an ionic double-layer effect and, for this reason, regard the term "conductive solids" as a misleading one. Some consideration has been given to the effect of dirty sands on the S.P. by Wyllie7 and by McCardell, Winsauer and Williams." Published work to date has cast light only on certain theoretical aspects of the problems created by the presence of clays and shales within permeable formations. One object of this paper is to describe experiments which serve to elucidate further the theory of the dirty sand problem and particularly the significance of the term "formation factor" as applied to dirty

Jan 1, 1955

By Richard P. Hight

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material, usually by rubbing action but also by impact (pressure blasting for example). They do not include abrasive tools, for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives, for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded abrasive products such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example: in garnet for sandpaper neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster that the ultimate cost will be less. It is for this reason that artificial abrasives have largely replaced natural abrasives. Abrasive Value Mineralogical hardness or "scratch" hardness as expressed in Mohs' scale is an important property in evaluating abrasive materials, but, as noted before, it is only one of several essential properties. The mineral hardness of pure crystal almandite garnet is about 7.5, but if the crystal is crossed by incipient fracture planes, or if it contains inclusions of other minerals, the apparent or useful hardness may be much lower. While the quartz grains in a sandstone have a hardness of 7, the bond holding the grains together may be so weak that the stone is valueless as a commercial abrasive. In artificially bonded wheels and stones, the hardness, strength, and character of the bond are fully as important as the hardness of the abrasive grains. Thus, in an overall consideration of abrasive hardness of loose abrasive grains, both "scratch" hardness and toughness must be considered. In naturally or artificially bonded abrasive stones, bond characteristics are a third factor, which is most important. The problem of abrasive hardness is further complicated by the inadequacies of methods of testing hardness and of expressing relative values. The Mohs' scale is inadequate both because the methods of testing are very crude and

Jan 1, 1983

By Nicholas J. Grant, Noboru Komatsu

Metallographic and X-ray studies were made of oxide dispersion strengthened Cu-12 vol pet SiO2 and Cu-3.5 vol pet Al2O3 alloys following time exposures at temperatures approaching the melting. point of the matrix metal. Changes in hardness, oxide particle size and crystal structure were studied to determine the time-temperature stability of these alloys. An interpretation of the mechanism of oxide agglomeration is proposed. One of the most striking features of dispersion strengthened metal-metal oxide alloys is their stability at elevated temperatures, both with respect to recrystallization and maintenance of mechanical properties after exposure at high temperatures. A small amount of work has been done on the re-crystallization phenomenon in dispersion hardened metal-metal oxide alloys'l and several theoretical treatments have been advanced regarding the stability of these alloys by Lenel and Ansell,8 and by Grant and his co-workers.9, 10 This paper reports on metallographic and X-ray studies following various heat treatments of Cu-AI2D3 and Cu-SiO2 alloys at elevated temperatures and the effect of subsequent cold work on the recrystallizalion temperature. An interpretation of the recrystallization behavior of this type of alloy, based on the decomposition and agglomeration of oxides, is proposed. EXPERIMENTAL PROCEDURE Cast ingot bars of copper-1.59 pet Si and Cu-0.77 pet Al, 7/8 in in diam, were annealed in argon for 80 hr at 1000CC for homogenization. The homogenized rods were machined into fine chips and ball milled. Milled particles in the range minus 20 to plus 60 mesh were separated for internal oxidation. The internal oxidation was accomplished by the same method used by Preston and Grant,9 except that the oxidalion temperature for the Cu-Si alloy was 750°C, and for the Cu-A1 alloy was 800°C. These powders were then hydrogen-reduced at 450°C, compacted in a copper container, evacuated at room temperature to 0.04 µ, and sealed for extrusion. They were extruded at 1400°F (760°C) with a ram speed of 55 in. per min for an extrusion ratio of 15.6 to 1 to give a rod 0.38 in. diam by about 3 ft long.

Jan 1, 1962

By J. H Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By J. H. Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957

By A. W. Gauger

For perhaps one hundred years scientists have been engaged in attempts at devising a satisfactory method of classification of coal. During this time many charts, tables and graphs have been proposed, some of which have had considerable merit, but no one system has been found to be applicable to all ranks of coal, nor has any one system received general acceptance. In many of the proposals, water eliminated between room temperature and 105" C. has been regarded as extraneous matter and calculations have been made to the air-dry or water-free basis. Such methods of calculation do not lend themselves to satisfactory grouping of the high-moisture coals.1, 2 A consideration not only of the properties of the high-moisture coals and their behavior on drying but of the generally accepted ideas of the coalification process and the role of water in this process indicates that water is an essential constituent of all coals and therefore should not be neglected. For example, in such low-rank coals as the lignites of the Northern Great Plains' deposits the inherent moisture of the lignite as mined plays a very important part in the physical properties thereof. Freshly mined lignite contains upwards of 30 per cent water and is extremely tough and resistant to shock. Upon exposure to the atmosphere, the lump loses part of its moisture and checks and splits, leaving a friable and broken up residue. So far as we have been able to determine, water is the only thing lost in this process and we are forced to the conclusion that moisture plays an extremely important part in the structural properties of the original lignite. With reference to the coalification process, Mack and Hulett3 pointed out in 1917 the important part that water played therein. They observed that water cannot be removed from peat or coal by pressure alone, but only as the result of chemical reaction, and suggested that peat in its early stages may be largely a hydrosol. Slow chemical changes occur over a long period of time until finally the mass becomes more largely a hydrogel. These views are substantiated to some extent by the experi-

Jan 1, 1932

D. EPPELSHEIMER, * Middletown, Ohio.-The housing of employees has so many and so varied aspects that in order to reach even an approximately correct solution it is necessary to have in mind a few fundamental principles; but it is not possible as yet to write these housing principles in the clear and correct form that is possible with many of our natural laws. Manifestly, the problem depends first on the kind of people it is necessary to house. What is suitable for the Southern unattached negro is not suitable for the married skilled American. The influx of colored labor has affected quite a number of what were satisfactorily housed communities. The second important factor is the relative proportion of the number of employees to the total employable population of the community in which the industry is located. The employer of a hundred men in. a large city has little responsibility in the matter of housing his employees. If he employs 75 per cent. of the employable population in a community of 27,000, as is the case of the company with which the writer is connected, it means a large responsibility. In the establishment of an entirely new plant in a more or less isolated place, the responsibility becomes greater. As engineers, we design and write the specifications for the machinery to accomplish a definite purpose, and proceed to house it, provide the necessary buildings with their accessories in the way of cranes, or heating systems, or sprinkling systems, as the case may be. There is no reason why the operating force should not be built up in very much the same way: design the organization, write its specifications so that the employment department can secure the proper men, and then house that organization with just as much thought and care as is given the plant. In the plant, the various machines will work along certain definite lines and accomplish certain results; but even if we start with the proper organization it takes considerable time to get that organization working together. One of the most important elements to this end is the proper housing of the organization. A man usually spends more time at home than at work. Proper surroundings and a comfortable, convenient house of good appearance exercise an influence that cannot be denied, and an employee situated in such surroundings is far more inclined to follow the policies of his employer and take an active part in furthering them

Jan 5, 1919

By Richard P. Hight

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean, or otherwise remove solid material, usually by rubbing action but also by impact (pressure blasting for example). They do not include abrasive tools, for instance, lathe tools and files--or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted al- though some chemical-action polishes and cleaners may also contain solid abrasives, for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded abrasive products such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cut- ting edges when grains become worn-for example: in garnet for sandpaper neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster that the ultimate cost will be less. It is for this reason that artificial abrasives have largely replaced natural abrasives. Abrasive Value Mineralogical hardness or "scratch" hardness as expressed in Mohs' scale is an important property in evaluating abrasive materials, but, as noted before, it is only one of several essential properties. The mineral hardness of pure crystal almandite garnet is about 7.5, but if the crystal is crossed by incipient fracture planes, or if it contains inclusions of other minerals, the apparent or useful hardness may be much lower. While the quartz grains in a sandstone have a hardness of 7, the bond holding the grains together may be so weak that the stone is valueless as a commercial abrasive. In artificially bonded wheels and stones, the hardness, strength, and character of the bond are fully as important as the hardness of the abrasive grains. Thus, in an overall consideration of abrasive hardness of loose abrasive grains, both "scratch" hardness and toughness must be considered. In naturally or artificially bonded abrasive stones, bond characteristics are a third factor, which is most important. The problem of abrasive hardness is further complicated by the inadequacies of methods of testing hardness and of expressing relative values. The Mohs' scale is inadequate both because the methods of testing are very crude and

Jan 1, 1975

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150'C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947

By John G. Koert, Koert D. Burnham, John G. Broughton

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By Koert D. Burnham, John G. Broughton, John G. Koert

Wollastonite in Essex County, New York, occurs as a typical contact mineral in a series of rocks metamorphosed by anorthosite. Sole current use is in various types of electric welding fluxes. Its uniform lathlike shape suggests its use as a specialized filler. Introduction Wollastonite (CaSiO3) was first noted in the vicinity of Willsboro, Essex County, New York, about 1810 by Dr. William Meade, and described from the same locality in 1821 by Lardner Vanuxem.' Recent exploration and development indicate that the deposit is of adequate size for continued exploitation on a larger scale than the present operations. The only other known occurrence of like magnitude in this country is in Kern County, California.* Wollastonite has been reported from Michigan, Pennsylvania, and Lewis County, New York, but these are little more than mineral localities. Geology The Essex County wollastonite has been found outcropping at numerous separate localities in a belt of contact metamorphosed sediments, 1/4 mile wide, which begins 2 miles southwest of the village of Willsboro and trends N. 70" W. for approximately 6 miles (Fig. I). In this belt, the pre-Cambrian Grenville has been injected and partially replaced by the more liquid portions of an anorthositic magma. Bud-dington and Whitcomb3 have described the rock in this contact metamorphosed belt as "Mixed gneisses: Grenville mafic, pyroxenic and garnetiferous gneisses and skarns* with local nearly uniform garnet or pyroxene layers and with gabbroic anorthosite sheets. A few limestone layers." These rocks are underlain, presumably at no great depth, by gabbroic anorthosite gneiss, the typical Whiteface border facies of the Adirondack anorthosite massif. The occurrence of wollastonite in large quantities was discovered during the quarrying of the garnet-rich layer that overlies the wollastonite at one opening. Further prospecting revealed its presence elsewhere in the belt, overlain in most places by the garnet. Accurate tracing of the wollastonite is difficult, owing to the glacial cover and to the fact that the weathered surface of the mineral has a dark, dirty brown color, and that the wollastonite itself has been dissolved more or less completely along the outcrops. It has, however, been noted at 10 localities within the skarn belt in the first 2 1/2 miles from its southeastern end. It has not been found in the northern half of the belt and therefore may be limited to the southern half. At the Fox Hill quarry, which is the main opening, 150 ft. have been exposed, showing an aggregate thickness of 30 to 35 it. Of

Jan 1, 1948

By G. S. Baker, S. H. Carpenter

Langenecker has reported significant reduction in strength of high-strength metals during ultrasonic t'ibration. Decreases in static yield stress an order of magnitude greater than the calculated stress amplitude of vibrations were reported by him for a stainless steel and for tungsten. in the present work, attempts were nzadc to verify such large reductions in yield and flats stresses using resonant librations of measured amplitudes. The results show that both the soft metals (copper and aluminum) and the high-strength metals (sleels) hare reductions in yield and .flow stresses no larger than the stress amplitude of libration. BLAHA and Langenecker,' investigating the effect of vibratory stresses on the deformation of zinc and aluminum, found a decrease in the static yield and flow stresses approximately equal to the vibratory stress imposed. Langenecker later extending this work to high-strength metals such as stainless steels and tungsten2 found a much larger effect. In these metals the static yield and flow stresses decreased by an amount more than an order of magnitude greater than the calculated vibratory stresses. It was suggested that this phenomenon could be a serious hazard to high-strength structures in an acoustic environment, such as a large rocket at launch, or could be used advantageously in the working of hard-to-work materials such as the refractory metals. Langenecker and others3 have investigated the effect of high-amplitude vibrations on many metal-forming operations. The results have been quite favorable with usually a large decrease in the energy necessary for the forming operation. The processes, however, involve large frictional forces and it is not clear whether the decreases in forming forces are to be ascribed to decreased friction or to decreased flow stresses. The present paper reports an attempt to determine the effect of accurately known vibratory stresses on the static yield and flow stresses. I) EXPERIMENTAL TECHNIQUE The standard multicomponent resonator technique for measuring internal friction has been adapted to allow simultaneous high-amplitude vibration, internal-friction measurement, and tensile deformation. This has been described in detail elsewhere.4 Longitudinal oscillations of approximately 50 kc frequency are excited in a multicomponent resonator by a quartz transducer. A second transducer measures the amplitude of vibrations. Fig. 1 shows a schematic drawing of the resonator and grip arrangement and the displacement pattern produced. Since the centers of the dummy bars are at displacement nodes, they represent points where attachments will not materially affect the vibrations. The force is applied by a standard Instron tester. The sample may be deformed while simultaneously vibrating at up to 104 strain amplitude. 11) EXPERIMENTAL RESULTS The effect of high-amplitude vibrations on the yield and flow stresses of copper. aluminum, tantalum. a soft iron, and a stainless steel has been measured. In addition samples of tungsten vibrating at stress levels up to 10' dynes per sq cm have been subjected to static stresses near the static yield stress with no indication of macroscopic deformation. Fig. 2 gives typical results for 99.999 pct polycrys-talline copper. A vibratory stress of 7 x 107 dynes per sq cm is applied at points "a" and removed at points "h". The behavior of aluminum is identical. In agree-

Jan 1, 1967

By Thomas P. Meloy, Duane T. Eppler

The science of particle shape analysis has expanded rapidly in the decade since precise numerical-statistical techniques were developed for use in characterizing the shape of closed forms. Use of Fourier descriptors permits shape to be quantified to whatever degree of precision is required. With this technique, particles and particle systems can be compared either on the basis of shape characteristics displayed by individual particles, or on the basis of aggregate shape characteristics representative of large samples of particles. Shape characterization work completed to date has shown that the physical characteristics of particle systems (porosity, permeability, strength, mechanical stability, chemical reactivity, and flow characteristics (viscosity)) are related directly to particle shape. Furthermore, it has been shown that particle shape is a function of chemical composition, process of formation, and post-formational history of the particle. In this light, particle shape analysis has potential applicability to a host of engineering and industrial problems encountered in processing particulate material. It can be used to optimize the efficiency of separation processes and particle feed systems, to trace particle pathways through processing systems, and to monitor the operation of specific processes, the wear of critical machine parts, and the quality of end products in processing systems. In this paper we discuss these specific applications of shape characterization to particle processing.

Jan 1, 1980

By Kung-Lee Wang, Brian W. Mackenzie, Warren E. Morrison, DeVerle P. Harris, George F. Sharrard

The term "mineral economics" is applied to a wide range of activities in the mineral industries. Earlier chapters have described the application of economic concepts to the mineral industries-supply, demand, conservation, tariffs, etc. The solution of mineral economics problems is often assisted by the application of quantitative methods. The purpose of this chapter is to describe a number of quantitative methods-econometric, operations research, and management science techniques-which find application in the analysis of mineral economics problems. These methods include input-output analysis, trend analysis, forecasting techniques, simulation, multivariate statistical analysis, mathematical programming, and market research techniques. The purpose of this introductory section is to provide a mineral economics framework for the application of these methods. Mineral economics is a subdivision of economics that is justified by a sufficient number of economic problems in the mineral industry requiring special experience and an unusual combination of skills. These problems are concerned with the conversion of minerals as geologic resources to minerals as economic goods. The mineral conversion process is outlined in Fig. 8.A.1. The physical occurrence of mineral deposits in nature and the market demand for mineral products in the economy provide the basic stimuli. The conversion process embodies a number of sequential stages-exploration, the development of mineral deposits, and mineral processing facilities and, consequently, productive activity to supply market demand. Changes in demand and the depletion of deposits illustrate the dynamics of the process. Mineral economics applies economic con-

Jan 1, 1976

By C. E. Wood, E. P. Barrett, T. L. Joseph

The United States Bureau of Mines has been studying the blastfurnace process for about ten years. An experimental furnace was developed by the Burcau in cooperation with the Minnesota School of Mines Experiment Station, University of Minnesota. Many data have been obtained and published.' Royster, Joseph and Kinney §(48) found that the particle size of ore had an important effect upon the blast-furnace process. Kinne(28) stated: Economy in blast-furnace practice depends largely upon efficient gas-solid contact in the shaft of the furnace. If efficient work is not done in the shaft, the hearth and bosh will not function properly. A condition may be readily imagined where the particles of ore in the shaft are so large that the time entailed in the descent of these materials into the bosh is not sufficient to permit proper reduction and preparation prior to the time the ore enters the bosh of the furnace. Another condition may be pictured where the density of theatock column and the flow of stock is such that the ore will take one course and the gas another. Both of these examples will result in insufficient contact between the gas and the ore. Unreduced ore will reach the hearth, and the gas which has not been efficiently oxidized will reach the stock line. The result is the use of an excess of carbon in the smelting process. It is obvious that fine ore particles occurring in the ore as charged, or formed in the furnace due to heat and mechanical action, place a definite limitation upon the efficiency of the operation. There is also an economic loss of fine material as dust. Effect of Size of Material Kinney reported (p. 83(29)) the reduction of iron oxides between planes at three furnaces as given in Table 1. The Chicago furnace was operated on Lake ores. Distribution of gas was not good and much of the charge passed into the hearth before the iron oxide was reduced. The Holt furnace was operated on coarse ore. Distribution of gas was fairly uni-

Jan 1, 1930

By J. D. Miller, J. E. Sepulveda

Tar sand deposits in the state of Utah contain more than 25 billion bbl of in-place bitumen. Although 30 times smaller than the well-known Athabasca tar sands, Utah tar sands do represent a significant domestic energy resource comparable to the national crude oil reserves (31.3 billion bbl). Based upon a detailed analysis of the physical and chemical properties of both the bitumen and the sand, a hot-water separation process for Utah tar sands is currently being developed in our laboratories at the University of Utah. This process involves intense agitation of the tar sand in a hot caustic solution and subsequent separation of the bitumen by a modified froth flotation technique. Experimental results with an Asphalt Ridge, Utah, tar sand sample indicated that percent solids and caustic concentration were the two most important variables controlling the performance of the digestion stage. These variables were identified by means of an experimental factorial design, in which coefficients of separation greater than 0.90 were realized. Although preliminary in nature, the experimental evidence' gathered in this investigation seems to indicate that a hot-water separation process for Utah tar sands would allow for the efficient utilization of this important energy resource. The projected increase in the ever-widening gap between the domestic energy demand and the domestic energy supply for the next few years has motivated renewed interest in energy sources other than petroleum, such as tar sands, oil shale and coal. Although a number of research programs on the exploitation of national coal and oil shale resources have already been completed, very few programs have been initiated on the processing of tar sand resources in the United States. In recognition of their significance as a domestic energy resource, investigators at the University of Utah have designed an extensive research program on Utah tar sands. An important phase of this program, and the main subject of this publication, is the development of a hot-water process for the recovery of bitumen from Utah tar sands, as a preliminary step toward the production of synthetic fuels and petrochemicals. The term "tar sand" refers to a consolidated mixture of bitumen (tar) and sand. The sand in tar sand is mostly a-quartz as determined from X-ray diffraction patterns. Alternate names for "tar sands" are "oil sands" and "bituminous sands." The latter is technically correct and in that sense provides an adequate description. Tar sand deposits occur throughout the world, often in the same geographical areas as petroleum deposits. Significantly large tar sand deposits have been identified and mapped in Canada, Venezuela and, the United States. By far, the largest deposit is the Athabasca tar sands in the Province of Alberta, Canada. According to the Alberta Energy Resources Conservation Board (AERCB),2,3 proved reserves of crude in-place bitumen in the Athabasca region amount to almost 900 billion bbl. To date, this is the only tar sand deposit in the world being mined and processed for the recovery of petroleum products. Great Canadian Oil Sands, Ltd. (GCOS) produces 20 million bbl of synthetic crude oil per year. Another plant being constructed by Syncrude Canada, Ltd. is expected to produce in excess of 40 million bbl of synthetic crude oil per year. According to the Utah Geological and Mineral Survey (UGMS), tar sand deposits in the state of Utah contain more than 25 billion bbl of bitumen in place, which represent almost 95% of the total mapped resources in the United States.4 The extent of Utah tar sand reserves seems small compared to the enormous potential of Canadian tar sands. Nevertheless, Utah tar sand reserves do represent a significant energy resource comparable to the United States crude oil proved reserves of 31.3 billion bbl in 1976.5 Tar sands in Utah occur in 51 deposits along the eastern side of the state.4 However, only six out of these 51 deposits are worthy of any practical consideration (Fig. 1). As indicated in Table 1, Tar Sand Triangle is the largest deposit in the state and contains about half of the total mapped resources. Information regarding the grade or bitumen content of Utah deposits is still very limited. The bitumen content varies significantly from deposit to deposit, as well as within a given deposit. In any event, the information available6-8 seems to indicate that Utah deposits are not as rich in bitumen as the vast Canadian deposits which average 12 to 13% by weight.9 Although many occurrences of bitumen saturation up to 17% by weight have been detected in the northeastern part of the state (Asphalt Ridge and P. R. Spring), the average for reserves in Utah may well be less than 10% by weight. Separation Technology As in any other mining problem, there are two basic approaches to the recovery of bitumen from tar sands. In one

Jan 1, 1979