Search Documents

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strainaging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 720°C. The time of treatment is relatively short (about 3 hr. to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say almost 30 per cent by volume. At this temperature, the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a very low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,000 lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantially constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1943

By S. F. Ravitz, S. R. Zimmerley

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By S. R. Zimmerley, S. F. Ravitz

High-grade cobalt concentrates were produced from the complex Blackbird ore with very good recovery in continuous pilot-plant operations in which a low-grade bulk cobaltite-pyrite flotation concentrate was roasted in a multiple-hearth furnace to oxidize the pyrite selectively. The cobaltite was floated from the resulting calcine. THE existence of the cobalt-copper deposits in the Blackbird district, Lemhi County, Idaho, has been known for many years. However, these deposits have not yet been exploited successfully because of the low grade of the ore, absence of information on ore reserves, and lack of feasible methods for concentrating and recovering cobalt from the ore. In 1941, when it appeared that World War II might interfere seriously with imports of cobalt from overseas, the U. S. Bureau of Mines started an extensive mining and metallurgical investigation of the Blackbird deposits. Exploration by trenching and drilling1 indicated that ore reserves were adequate to warrant consideration of large-scale exploitation. A process for producing high-grade cobalt concentrates from the ore was developed at the Salt Lake City Station of the Bureau,2 and hydrometallurgical procedures for producing cobalt metal or oxide from the concentrates were developed at the Boulder City Station.3 The Howe Sound Co., through a subsidiary, the Calera Mining Co., carried out further exploratory work, which increased probable ore reserves to a tonnage commensurate with a large investment in mine, mill, transportation facilities, and refinery. Simultaneously, the metallurgical staff of the company, working in cooperation with the Bureau of Mines, further investigated the metallurgical problems. It was the opinion of both groups that pilot-plant testing was required to translate laboratory results into plant operation. In general, the Blackbird ore has a high content of pyrite and some pyrrhotite and contains 0.5 to 1 pet cobalt and 1 to 2 pet copper, which are present essentially as cobaltite and chalcopyrite. The copper can be recovered readily as a high-grade concentrate by selective notation. The cobalt then can be recovered as a bulk sulphide concentrate assaying 4 to 5 pct cobalt, but no satisfactory procedure for separating the cobalt from the pyrite and pyrrhotite directly by flotation had been found. The method developed by the Bureau for producing a high-grade cobalt concentrate is essentially an application of the old Horwood process of selective roasting.4 The bulk sulphide concentrate is roasted to form an oxide coating on the iron mineral particles, and the calcine is then treated by flotation. The oxide coating prevents the iron minerals from floating so that it is possible to obtain a high recovery of cobalt in concentrates assaying more than 20 pct cobalt. Laboratory tests by metallurgists of both the Bureau and the Howe Sound Co. had indicated the optimum roasting temperature to be 425° to 450°C. At lower temperatures the rate of oxidation of the iron minerals is too low, whereas at higher temperatures substantial quantities of cobalt are rendered water-soluble. Because of its high sulphur content (35 to 40 pct), the bulk concentrate tends to continue to burn after it has reached the optimum roasting temperature. Although excessive temperatures could be avoided in the small-scale laboratory furnaces, there was considerable doubt that the temperature could be controlled properly in industrial equipment. To provide material for the pilot-plant tests, the Calera Mining Co. installed a small, temporary flotation mill at the Blackbird property and treated

Jan 1, 1951

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham', Eckel' and others .' However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger' led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By Eric K. Albert, J. Kiusalaas

The paper presents an overview of SPASID (Kiusalaas and Albert, 1983), a new computer program developed under U.S. Bureau of Mines funding for the prediction of surface subsidence caused by under- ground mining operations. The presentation, which is illustrated with two case studies, also re-evaluates the influence function method as a tool of subsidence prediction, arriving at some rather unconventional recommendations. SPASID consists of four modules that communicate through common data bases: (1) Preprocessor. This module prepares and maintains the database for the entire site. The database contains all the information about the site and the mine operation that is necessary for the computation of subsidence. (2) Subsidence Predictor. The influence function method is used to predict the surface displacements that occur in any portion of the site that occur between two given dates. The computations take into account the time lag between extraction and displacement, and the effects of pitching seams and incomplete compaction at the edges of panels. The program contains i not he's influence function and the Green's function of transversely isotropic elasticity theory. (3) System Identification. The purpose of System Identification is to determine the optimal values of the various parameters associated with the influence functions in the Subsidence Module. System Identification requires measurements of subsidence from a site with a sirnilar overburden structure. The values of the subsidence parameters are obtained by minimizing the discrepancy between the measured and computed surface displacements. (4) Postprocessor. The Postprocessor is a graphics facility for displaying the data generated by the other program modules.

Jan 1, 1984

By Pete Turcic, Wade E. Cooper

Many factors influence radon-222 influx and radon-daughter concentrations in underground uranium mines. A brief review of some of these factors is presented. Current radon-222 and radon-daughter control principles and practices for U.S. underground uranium mine atmospheres are discussed and a brief review of the applicability of other possible control methods such as rock sealants, radon-222 removal, and radon-daughter removal is given.

Jan 1, 1982

ALABAMA Anniston.-Bretz, J. A. Carrington, F. G. Gerber, A. B. Klugh, B. G. Semple, R. A. Ashland.-Barton, .J. Bessemer.-Abbott, C. E'. Ball, T. L. Beaver, J. J. Ferguson, V. Salmon, H. S. Sehaber, C. F. Whatley, W. J.

Jan 1, 1923

OFFICERS AND COMMITTEES C C Long, President John Chipman, Past President J S Smart, Jr, Vice President T D Jones, Treasurer R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y D C Johnston, Assistant Secretary

Jan 1, 1960

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1910

United Engineering Society ARTHUR S. DWIGHT KARL EILERS J V N DORR Engineering Societies Library Board SYDNEY H. BALL JOSEPH E POGUE GEORGE C STONE JOHN H. JANEWAY Engineering Foundation Board J. V N. DORR JOHN M CALLOW GALEN H CLEVENGER

Jan 1, 1923

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RIVHARD W HUNT 1883

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RIVHARD W HUNT 1883

Jan 1, 1910

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

PRESIDENTS DAVID THOMAS 1871 R W RAYMOND 1872-1874 A L HOLLEY1875 ABRAM S HEWITT 1876 T STERRY HUNT 1877 ECKLEY B COXE 1878 - 1879 WILLIAM P SHINN 1880 WILLIAM METCALF 1881 RICHARD P ROTHWELL 1882 RICHARD W HUNT 1883

Jan 1, 1917

By H. I. Aaronson, H. A. Domian

ELectvon-probe analgsis has been used to in7:estigatr the partition ot alloying- elements between aus-tenite and proeutectoid ferrite (or the Jerritic component of bainite) in high-purity Fe-C-X alloys, lsuully at tzco levels of carbon content fca 0.1 and 0.4 pct in ntost steels) at temperatures between the M, and the Ae3 in Si, mn, Ni, mo, Co, Al, Cr, Cu, and PI steels. No partition ous found during the early stages of transformation at any temperature studied in the Si, ,mo. Co, Al, Cr, and Cu steels. Partition did take place, Jrowel'er, in Ihe Mn, ATi, and Pt steels, occurring in lewtperature. regions below the Ae3 of ca 130°, 65", UNDERSTANDING the mechanisms through which alloying elements influence the kinetics of austenite decomposition reactions which proceed by nucleation and 35c respectively. A break was discovered in the TTT curve for the initiation oj the proeutectoid ferrite reaction in the latter steels at the temperature at which partition began. The alloy content in ferrite at the a:y bondavy remained at constart lecels, shown experimentally to be significantly above those corresponding to eqiilib+iu??l, e'en at the longest reaction times investigated (ca 1o6sec). The partition and the TTT curve observations foere rationalized on the basis of the thermodynamic treatment developed in an accompany ing paper. and diffusional growth has been a major research objective of physical metallurgy since the latter part of the 19th century. The measurements made on the dif-fusivities of carbon and of substitutional alloying elements in austenite during the 1930's and 1940's seemed to provide a useful clue as to the nature of these mechanisms. These measurements showed that the diffu-sivity of carbon is several orders of magnitude higher than that of the alloying elements at a given tempera-

Jan 1, 1967

By C. L. Sollenbeger, R. B. Greenwalt

PERHAPS the most widely used dispersants or gangue depressants in nonmetallic flotation are sodium silicates, which vary in silica-to-soda ratio from 1 to 3.75. Typical manufactured silicates in order of decreasing solubility and increasing amounts of silica are Metso, silica-to-soda ratio of 1.00; D, 2.00; RU, 2.40; K, 2.90; N, 3.22; and S-35, 3.75.* References in flotation literature1,2 to the use of sodium silicates are often weak because they fail to mention the type of silicate used. Metso and silicate N have occasionally been mentioned, but when the type of silicate is not mentioned, it is usually assumed to be N, the cheapest of the soluble silicates and the one recommended by sodium silicate manufacturers as a flotation agent. In the All is-Chalmers Research Laboratories a systematic study was made of the effect of different alkali-silica ratios on the concentration by flotation of two scheelite ores. One of these was a high grade ore from the Sang Dong mine in Korea. The effect of such factors as pH; addition agents; and conditioning time, temperature, and pulp density on the flotation efficiency of this ore have been described previously. The other ore was a low grade ore from Getchell Mines Inc., Nevada. The mineralogy and techniques of concentrating this ore have been described by Kunze. Hereafter these ores will be referred to as the Korean and Nevada ores. Experiments were made with both to determine the effect of three factors—-type of silicate, concentration of silicate, and pH of the pulp—on recovery and grade of tungsten in a rougher concentrate. Average WO, content of the Korean ore was 1.50 pct and of the Nevada ore 0.27 pct. The predominant tungsten mineral in both ores was scheelite, which was accompanied by a small amount of powellite. The powellite and scheelite were finely disseminated through both ores and required a —200 mesh grind for liberation. Major gangue minerals in the Korean ore, in decreasing order of abundance, were amphi-boles, quartz, biotite, garnet, fluorite, and calcite. Bulk sulfides composed about 3 pct of the total weight. Gangue in the Nevada ore, in descending order of abundance, was garnet, alpha quartz, calcite, phlogopite, wollastonite, and amphiboles. Sulfide minerals were 3 to 4 pct of total weight. Batch flotation experiments were made with 500-g samples of ore, each sample wet-ground to 90 pct passing 200 mesh. The finely ground ore was floated in a Fagergren batch cell at 25 pct solids. The natural pH of the Nevada ore was 8.9 and of the Korean ore, 8.5. The D, RU, K, N, and S-35 sodium silicates were obtained in colloidal dispersions with varying amounts of water. The most alkaline, Metso, was in dry powdered form. For convenience in addition, 5 pct solutions by weight were prepared from each of the silicates, on the basis of dry sodium silicate dissolved in the correct amount of distilled water. Chemical analyses of the various silicates are given in Table I, together with the pH of the 5 pct solutions. A preliminary bulk sulfide float was made with secondary butyl xanthate as the collector and pine oil as the frother. The WO] analysis of the sulfide concentrate was nearly 1 pct for the Korean ore and about 0.1 pct for the Nevada ore. The tungsten contained in the sulfide concentrate constituted about 3 pct of the total tungsten in each ore. No effort was made to recover these tungsten values. The scheelite was floated with oleic acid. Adjustments in pH were made with sulfuric acid or sodium carbonate. A 1 pct solution of 85 pct Aerosol OT was sprayed on the froth and sides of the cell during the scheelite float to aid in dispersing the minerals and to decrease the entrapment of gangue particles. Six tests were planned for each of the six types of silicate in which concentrations of 1, 2, and 4 1b of silicate per ton of dry ore were investigated at both 6.5 and 10 pH. All tests were made at room temperature. The performance of each silicate was judged from the grade and recovery of WO, in the scheelite rougher concentrate. Tungsten recovery was calculated on the basis of the scheelite remaining in the ore after the preliminary sulfide float. Testing of each silicate at three levels of concentration and two levels of pH required 36 tests with each scheelite ore. Variance analyses were performed on the concentrate grades and recoveries to determine whether or not the type of sodium silicate, the concentration of sodium silicate, or the pH significantly affected recovery or grade. Results Concentrate Grade: A variance analysis of the concentrate grades for the Korean ore showed that concentration of the silicate and pH of the ore pulp were major factors in producing a high grade concentrate. Also, the silica- to-so da ratio was important as an interaction with pH. The concentrate grade vs silica-to-soda ratio is plotted in Fig. 1. The curves show that the concentrate grade improved with an increase in concentration of sodium silicate and also

Jan 1, 1959