Search Documents

By Ancel St. John

AT THE New York meeting of the Institute of Metals Division in February, 1927, Jeffries and Tarasov presented a paper on Tungsten and Thoria,1 in which the experimental facts were interpreted in accordance with the prevailing point of view that the thorium is present as the oxide, thoria. In discussing that paper the writer of this article stated that his own investigations, which had been unavailable to Messrs. Jeffries and Tarasov, showed that the so-called "thoriated" tungsten filament failed to disclose any sign of the oxide when subjected to X-ray diffraction analysis, but did give plenty of evidence of the presence of metallic thorium and, in certain cases, of a material believed to be an alloy of tungsten in thorium. Since these results were completely at variance with the results reported in the paper under discussion and with other papers which had preceded it from time to time in the past, it was felt that further discussion should be withheld until the new evidence could be presented adequately. Arrangements were therefore made to present that evidence at this meeting. MATERIAL EXAMINED The material examined was high-emission filament such as is used in radio tubes, supposed to contain about 0.75 per cent. thoria. The actual analysis was not stated. SCOPE OF THE INVESTIGATION The investigation was undertaken because of a feeling that the thorium present in filamentary material of this type exists as metallic thorium or as an alloy of thorium and tungsten and not as the oxide. Attention was therefore directed to determining: 1. The minimum amount of thoria detectible in a mechanical mixture of thoria powder and finely divided tungsten. 2. The amount of thoria detectible in the filament. 3. The condition of any thorium present in other form than as thoria. 4. The amount of thorium dissolved in the tungsten.

Jan 1, 1928

By Thomas M. Drown

THE means relied on to attain uniformity in Bessemer steel may be enumerated as follows I. The appearance of the flame. II. The appearance of the slag. III. The spectrum of the flame. IV. Examination of the steel itself. At present, I wish briefly to bring forward a few considerations with reference to the last two mentioned, namely, the conditions favoring the employment of the spectroscope and examination of the steel. From the amount of careful investigation which has been devoted to the examination of the Bessemer flame by the spectroscope, both on the part of scientists and practical metallurgists, one might reasonably expect some results definite and satisfactory in their nature, first, as regards the nature of the flame, and second, as to the practical value of the spectroscope as a guide in conducting the process. We find, in fact, however, that uncertainty and confusion still exist. In Germany, where this subject has received the greatest attention, it is now very generally conceded that manganese is the cause of the well-known groups of dark bands that characterize the Bessemer spectrum. Nor is it easy to see how we can avoid accepting this conclusion, when Wedding and Von Lichtenfels have produced the manganese spectrum and found it to correspond closely with that shown by the Bessemer flame. But it is evident, on a moment's reflection, as Roscoe has recently brought forward, that manganese cannot be the only cause of the Bessemer spectrum, for we notice the characteristic bands quite as

Jan 1, 1873

By Joseph J. Becker

RECENTLY the "oriented growth" hypothesis of recrystallization textures has been receiving considerable attention. According to this view, "whenever a new generation of grains is growing in a highly oriented matrix . . . one may assume . . . that from among available nuclei of a great variety of orientations those with suitable orientation relationship with respect to the matrix have by far the highest rate of growth (oriented growth) and will, therefore, predominate."' This statement includes primary recrystallization of single crystals and of polycrystalline materials showing strong deformation textures as particular cases. While the phenomenon of oriented growth undoubtedly does operate, and may be of importance in coarsening or secondary recrystallization, the writer feels that its extension to primary recrystallization is a different matter. Several aspects of this phenomenon may be pointed out which are difficult to rationalize on the basis of oriented growth. In recrystallizing deformed single crystals of alpha brass, Maddin, Mathewson, and Hibbard2 found that the twin composition planes of the recrystallized grains were parallel to the three operative slip planes they observed, and not to the fourth octahedral plane. The writer's current work seems to indicate further that when only one or two slip systems can be seen to operate, the recrystallized grains are aligned only with those slip planes actually observed. This behavior could hardly be accounted for by oriented growth, because on the latter basis the recrystallized texture of a deformed single crystal should certainly have the same symmetry as the crystal itself. Growth rates could not be expected to distinguish between crystallogra- phically equivalent directions, unless the presence of a visible slip system vastly increases the growth rate in the appropriate direction. This seems unlikely. These relationships were observed by the writer only when considerable care had been exercised before annealing to etch away the effects of cutting out the centers of tensile specimens with a jeweler's saw and to etch off the ends of compression specimens. When these.precautions were not taken, nu-cleation inevitably appeared to occur at the saw cuts or at the ends, and the resulting orientations never showed a [111] rotation but appeared quite random. The provision of many nuclei of many orientations did not enhance the correlation, but destroyed it. Recrystallization textures are sometimes strongly dependent on annealing temperature, which would imply that the anisotropy of growth rates is a suddenly varying function of temperature. This might be regarded as unlikely. Recrystallization textures can be strongly dependent on the degree of deformation. If textures are to be explained by selective growth from among nuclei of all orientations, it is difficult to see how the recrystallization process could have any dependence whatever on the manner or degree of deformation. It is felt that the above points should be considered before the oriented growth hypothesis is applied to primary recrystallization, with the necessary complete divorce of the mechanism of recrystallization from the details of the deformation process. References 1P. A. Beck and H. Hu: Reply to discussion of their paper on Recrystallization Texture and Coarsening Texture in High Purity Aluminum. Trans. AIME, 188, 1057; Journal oF Metals (Aug. 1950) TP 29083. 'R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins in Brass. Trans. AIME, 185, 655; Journal of Metals (Sept. 1949) TP 26763.

Jan 1, 1952

By S. R. Krom

In connection with perfecting a system of pneumatic concentration I had in view the improvement of machines for crushing and pulverizing ores. A study of the whole subject convinced me that the principle upon which the construction of the Blake crusher, and that of rolls, is based, possessed the mechanical elements which, if perfected and simplified, would make these machines the successful rivals of every other device. It is well-known that until very recently the stamp-battery held undisputed possession of the field; and mill-men and mill-builders almost universally believed that stamps would not be superseded by any other machine for fine crushing. The first step to drive stamps from the field was the introduction of rollers in the Bertrand and the Mt. Cory mills. In both of these mills the great superiority and economy of a system of crushing with rollers instead of stamps has been fully demonstrated. While perfecting the rollers, I had the fact confronting me that they had frequently been tried without success. In fact, the universal opinion prevailed that rollers could be used only for coarse, and not for fine crushing. The secret of the difficulty I discovered to lie in the imperfect and weak character of the rolls heretofore used, due to a misconception of the requirements for a machine for such work, and a failure to appreciate the advantages of continuous, rolling, crshing- surfaces, operating on the toggle-lever principle, which gives the greatest crushing pressure with the least power. expended, and the minimum of wear.

Jan 1, 1886

By H. P. Willard, Conrad Martin

SINCE the deposits were found in 1927 in the Paradise Range of western Nevada, more than 1 mil- lion tons of magnesite and half a million tons of brucite have been mined and processed into a variety of granular refractory materials used as furnace linings by the steel industry. An additional million tons of magnesite were used during World War II to produce magnesium metal, and some magnesium oxide from the area is going into magnesia cements. Located near Gabbs, Nev., on the west flank of the Paradise Range, the principal bodies occupy an area a mile long by half a mile wide, and lesser occurrences have been found in a belt more than four miles long and in places almost two miles wide. Magnesite reserves containing less than 5 pct lime are estimated at more than 25 million tons. Reserves of better grade material are considerably less.

Jan 4, 1957

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."1 It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data 2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. HARDNESS, LATTICE PARAMETER AND IONIC OVERLAP Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2, It is believed that most of the values are accurate within the limits indicated by the rectangles, These data are also presented in Table I. Ultimate Meyer hardness, Pu, is defined by the equation: [P" - D2] where L = load, D = diameter of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro¬duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. [ ] The question arises as to whether or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By Guido Del Giudice

THE term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(1)? Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince; 3 Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) OLD THEORY OF SLIME-COATINGS At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and, on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince's experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed.

Jan 1, 1934

By John A. Oberteuffer, Ionel Wechsler

High gradient magnetic separation, first introduced in 1968 as a means for the removal of very fine magnetic contaminants from clay, is no longer a new technology. Applications to a number of solid-solid and solid-fluid separation problems are now being exploited. Recent pilot tests and full-scale industrial installations of high gradient magnetic separators and filters have established their commercial viability and have demonstrated their superiority both in efficiency and cost effectiveness to conventional prior-art methods for water treatment and mineral processing. In high gradient magnetic separators, the magnetic trapping force for fine, even weakly magnetic particles is greatly increased over those available in previous magnetic separators. These very strong trapping forces are created on the edges of fine filamentary ferro- magnetic materials in the presence of a strong background magnetic field. In the basic cyclic high gradient magnetic separator, particles are trapped in the filamentary matrix until it is loaded, at which point the magnetic field is turned off, and the filter is back- flushed. Applications of cyclic high gradient magnetic filtration for water treatment include filtration of waste and process waters in steel mills. Treatment of hot rolling mill scale pit effluent and cold rolling mill emulsion has been successfully tested, and 2-meter diameter SALA-HGMF® magnetic filters have been installed at Japanese steel companies for the treatment of recirculating scrubber waters in a de-gas- sing system. A second major application in water treatment is for the polishing of recirculating waters in power and steam generating systems. High gradient magnetic filters can operate under conditions of

Jan 1, 1980

By A. K. Gangopadhyay, J. J. Moore

The effect of grinding media composition, mineral type, and slurry environment on the wear rate of various grinding media (balls) are discussed. Sufficient wear data have been obtained and correlated. Modes of wear were determined from examination of the ball surfaces using scanning electron microscopy. Five modes of wear have been identified to be operative under certain slurry conditions for the various ball compositions studied.

Jan 1, 1986

By Norman Pilling

The micrographic analysis of silicon steels is possible if a dilute solution of nitric acid and methyl alcohol in nitrobenzol is used. The action of this reagent differs from that of sodium picrate in that there is no persistent deep-seated staining and the solution is used cold. THE technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105° C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys.

Jan 1, 1924

By Arthur Taggart

FLOTATION of ores is a practical utilization of the energy that resides in the surfaces of solids and liquids. The best known manifestation of this energy is called surface tension; an equally important, though less apparent, phenomenon is adsorption. This paper reviews some of the recent investigations of these phenomena, and gives the results of certain experiments performed by the authors. Surface tension is a manifestation of energy having its seat at the bounding surface between the adjacent phases of a multiphase system. Thus, at the interface between a liquid and a gas, or between two immiscible liquids, or between a solid and a gas or a liquid, there are forces capable of doing work, their magnitude depending on the nature of the adjacent phases and the extent of the bounding area. These surface forces are inappreciable when the ratio of surface to volume of the adjacent phases is small, but they become powerful when this ratio becomes large, as it does when one of the phases is highly dispersed. Froth flotation, which consists in buoying solids heavier than water to the surface of water by means of gas bubbles, utilizes the force of surface tension to attach the solid particles to the gas bubbles and again to maintain the floating mass of bubbles as a more or less persistent froth at the surface of a pulp for a sufficiently long time to allow its removal. It follows from the second law of thermodynamics that the potential energy of a system in equilibrium is a minimum. Therefore a multiphase system, tending toward equilibrium, will arrange itself in such a way that the total energy of the interfaces will be the least possible. This end can be accomplished in two ways: by a change in shape that will reduce the interfacial area; by a change in the nature of the surface layer in

Jan 8, 1922

By John C. Branner

Five of the geologic horizons that yield oil in other parts of the world are represented in Brazil; namely, the Devonian, Carboniferous, Permian, Cretaceous, and Tertiary. Thus far, the first two have shown no evidences of being oil bearing within Brazilian territory. Not enough exploring has been done to permit trustworthy comparisons of the relative importance of the Permian, Cretaceous, and Tertiary as oil-bearing horizons in this country. The most important, indeed almost the only, information available relates to the locations of the areas and to the structural features of the several horizons. The theories regarding the physical conditions under which these rocks were laid down, however, I regard of the utmost importance. Permian Rocks of Permian age cover an enormous area in Brazil, extending from Rio Grande do Sul to Maranhao on the north, and to Matto Grosso on the west. These Permian rocks in many places are known to include oil-bearing shales and in some locations contain small veins of gilsonite. The geologic map of Brazil shows that the Permian area is widely distributed, but there is considerable doubt about the origin of some of the rocks. Some of the lower Permian beds in southern Brazil contain marine fossils, but in Minas no fossils have as yet been found in them, and in Bahia, at only one locality have a few Permian plants been found. Indications of oil have been found in the states of Sa0 Paulo, Parana, and elsewhere farther south, but wells drilled in the Permian of SaO Paulo near the Morro do Bofete did not find oil. One well has been started, by the Brazilian Government, in the Permian of Parana near Marechal Mallet, close to latitude 26" south, but thus far oil has not been found.

Jan 1, 1923

By John C. Branner

Five of the geologic horizons that yield oil in other parts of the world are represented in Brazil; namely, the Devonian, Carboniferous, Permian, Cretaceous, and Tertiary. Thus far, the first two have shown no evidences of being oil bearing within Brazilian territory. Not enough exploring has been done to permit trustworthy comparisons of the relative importance of the Permian, Cretaceous, and Tertiary as oil-bearing horizons in this country. The most important, indeed almost the only, information available relates to the locations of the areas and to the structural features of the several horizons. The theories regarding the physical conditions under which these rocks were laid down, however, I regard of the utmost importance. Permian Rocks of Permian age cover an enormous area in Brazil, extending from Rio Grande do Sul to Maranhao on the north, and to Matto Grosso on the west. These Permian rocks in many places are known to include oil-bearing shales and in some locations contain small veins of gilsonite. The geologic map of Brazil shows that the Permian area is widely distributed, but there is considerable doubt about the origin of some of the rocks. Some of the lower Permian beds in southern Brazil contain marine fossils, but in Minas no fossils have as yet been found in them, and in Bahia, at only one locality have a few Permian plants been found. Indications of oil have been found in the states of Sa0 Paulo, Parana, and elsewhere farther south, but wells drilled in the Permian of SaO Paulo near the Morro do Bofete did not find oil. One well has been started, by the Brazilian Government, in the Permian of Parana near Marechal Mallet, close to latitude 26" south, but thus far oil has not been found.

Jan 1, 1923

By H. F. Dawes

In China all minerals are, theoretically at least, the property of the Emperor, and the Imperial permission must be got from him for the privilege of working them. A direct tax is levied on this privilege, and by simple command, the Emperor can close a mine at any time. Occult geomantic influences are a large factor in determining the opening or the arbitrary closing of a mine. The location with reference to points of the compass, graves and natural objects, may be really or professedly considered as indicating that those influences are favorable or unfavorable. The consequence, is, of course, that for the authorization and encouragement of any considerable enterprise, friends' at court, practical politics, and more or less bribery, are required. As a result, most Chinese mining is illicit, and is carried on in a small way only. Often along a single vein, or over a small section of mining country, a few individuals obtain rights over all the openings, most probably by loaning money to the head-men of the operators and holding the mines as security for the debt. In such cases, perhaps, for better security, all the ore is reduced in the works established by the creditors, who also handle all silver produced..As the head-men are, for the most part, improvident, and the laws and customs for the collection of' debts are stringent and peculiar, the " officemen" or creditors acquire in time what is practically an ownership of

Jan 1, 1892

By Eckley B. Coxe

IN making surveys in the anthracite coal regions of Pennsylvania, the ordinary engineer's chain (50 or 100 feet long) is generally used, both above and below ground. Sometimes, where it is difficult to chain, as, for instance, across a chasm, a wire is stretched from one station to the other, the distance is marked on the wire and its length is then measured with the ordinary chain. Having had occasion lately to make some surveys where it was necessary to determine with great accuracy the position of the land or property line, not

Jan 1, 1874

By Zay Jeffries

EACH generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwith-standing their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization.

Jan 5, 1924

By Bernard Schneider

The diversity of methods available to engineers and geologists for studying rock masses is a reflection of the fact that, despite the rapid and encouraging progress made over the last few years, there is still no unified and comprehensive method which can be used to predict the over- all behavior of a foundation. Nevertheless, it is agreed that the fundamental characteristic affecting the engineering properties of rock is fissuration, and this paper de- scribes a few new or improved methods of studying fissuration and its influence on major engineering factors such as permeability, deformability, or internal stresses in the rock volume. TESTS ON SAMPLES Conventional tests on samples using thin slices can be improved by staining the slices before cutting with certain ionic dyes which have an affinity for certain types of surface. This shows up the microdiscontinuities. For example (quoted terms are French trade names) : "Turquoise Motylhne JSA" will show up porous alteration of basic feldspars. "Vert brillant SA" is used for acid feldspars. "Fushine ASA" will show up voids in all rocks. A mixture of "Turquoise" and "Rhodamine BSA" will show up zones of alteration in all types of feldspars. With this technique, it is easy to make an optical classification of the different structural types, e.g.: (1) rocks completely free from voids; (2) rocks with microfissures, which in turn can be subdivided into (a) rocks with microfissures secant to the mineral structure, (b) rocks with microfissures parallel to the mineral structure, and (c) rocks with ran-

Jan 1, 1970

By Thomas L. Watson

The occurrence of zircon in pegmatites of acidic composition is recorded by many observers both in this country and abroad, and they form one of the most important geologic modes of occurrence of the minera1. As is well known, commercially the most important American locality for zircon is near Zirconia in Henderson County, North Carolina, where many tons of the mineral have been obtained from a kaolinized pegmatite dike 100 ft. wide and traced for 1 1/2 miles along the direction of strike N. 50" E. Zircon may be developed in pegmatites as inclusions in the principal rock-forming minerals, chiefly quartz and feldspar, and as a separate megascopic constituent in the form of grains and crystals not exceeding, as a rule, 2 in. in size, and usually smaller. In the Henderson County, North Carolina, pegmatite, zircon occurs in prismatic crystals with pyramidal terminations measuring up to 30 mm. in diameter, associated chiefly with the feldspar. In some of the apatite veins of Canada, which are closely allied to pogmatite dikes, zircon is reported in crystals upward of 6 in. in length and 2 in. and more in thickness. Zircon in large masses occurs in Virginia in the well-known pegmatites near Amelia in Amelia County, and near Gouldin in Hanover County. Both localities are in the middle eastern portion of the Piedmont Plateau province, and are separated by a distance of about 40 miles in a northeast-southwest direction. The rocks of both areas, including the pegmatite bodies, are in an advanced stage of decay, and the hard and moderately fresh rocks are concealed beneath a cover of variable thickness of rock decay derived by the normal processes of weathering. Exposures, there-

Jan 1, 1917

By Thomas Darlington

THE obligation of an employer to the State requires certain things of him as matters of good citizenship: for instance, that his workmen shall have a living wage, that child labor shall not be employed, that injuries from accidents shall not- make workmen a charge upon the State, and that the laborer's children shall have opportunity for education and to become good and useful citizens. Affairs of this kind are not taken up as philanthropy, for the officials of a corporation or a large manufacturing concern may not feel at liberty to spend the funds of their company as prompted simply by motives of kindliness; but they may spend company money on such matters because it is good business. For years, the poisonous effects of lead, phosphorus and dust have been emphasized in books on industrial hygiene and their elimination has been urged; but the more important and everyday physiology of the workman himself has been neglected. Part of my object in writing this paper is to show how our knowledge of physiology may be applied to working conditions in everyday life. In the interest of industrial laborers, accident compensation laws have been enacted in 33 States. This has been carried forward rapidly, because it has been shown that it pays both employer and employee. A further step is the recognition of sickness and disablement independent of accidents, not only because of their immediate cost to the worker and to the employer, but because continued efficiency in work and business depends largely upon health. Some measure of the importance of health in industry can be gained by the knowledge that records kept by some companies which now make this the subject of careful inquiry show that the time lost by employees, through illness; is several times as much as that lost as the result of industrial accidents. It is true that accidents frequently result in permanent disability or death, but it is equally true that illness is also a cause of permanent disablement or death. Thus the chief difference is that the loss to the employee through accidents occurring in the course of his employment is now generally recognized as a cost

Jan 2, 1918

By Takao Kobayashi

Micro-crack formation zones developed near a crack tip in rocks and ceramics play a significant role in fracture behavior of these materials. In order to study micro- crack formation near a crack tip and its effects on crack behavior, a mica-epoxy composite material was developed. Multi-layer mica flakes were embedded in an epoxy matrix. Under high stress in the vicinity of a crack tip the mica delaminated, simulating the micro-cracking along grain boundaries or crystal planes in rocks and ceramics. A compact tension specimen was fabricated from mica-epoxy composite material. During the test the load and crack opening displacement were measured following the ASTM E561 (R-curve determination) procedure. Through the compliance calibration method the effective crack length and the KR were computed. The experiment clearly demonstrates the formation of micro-cracks and their effects on the overall behavior of the specimen. The paper discusses the significance of micro-crack formation on fracture toughness characterizations, and the advantages of the use of mica-epoxy composite for detailed studies of interaction between the micro-crack formation zone and the specimen geometry and size.

Jan 1, 1982