Search Documents

By C. T. Wei, A. Kelly

USING a recently developed X-ray method, reported by Schulz,2 it is possible to make a rapid survey of the perfection of a single crystal at a particular surface. This technique has the advantage of allowing a large surface of a specimen to be examined by taking a single photograph and it compares well with other X-ray methods in regard to sensitivity of detection of small angle boundaries. During the course of a survey of the perfection of large crystals of aluminum produced by a number of methods, an examination has been made of a number of single crystals produced from the melt using a soft mold (levigated alumina)." Crystals grown by this method are known, from an X-ray study carried out by Noggle and Koehler,3 to contain regions where they are highly perfect. In the present work, it has been possible to obtain photographs showing directly the distribution of low angle boundaries at a particular surface of these crystals. single crystals were grown from the melt using the modified Bridgman method with a speed of furnace travel of -1 mm per min. These were about 1/10 in. thick, 1 in. wide, and several inches long. The metal was 99.99 pct pure aluminum supplied by the Aluminum co. of America. The crystals were examined by placing them at an angle of about 25° to the X-ray beam issuing from a fine focus X-ray tube of the type described by Ehrenberg and Spear4 and constructed by A. Kelly at the University of Illinois. A photographic film was placed SO as to record the X-ray reflection from the lattice planes most nearly parallel to the crystal surface. The size of the focal spot on the X-ray tube was between 25 and 40 u, and the distance from the X-ray tube focus to the specimen (approximately equal to the specimen to film distance) was -15 cm. White X-radiation was used from a tungsten target with not more than 35 kv in order to reduce the penetration of the X-rays into the specimen. Exposure times were approximately 1 hr with tube currents between 150 and 250 microamp. The type of photograph obtained from these crystals is illustrated in Fig. 1, which shows a number of overlapping reflections from the same crystal. The large uniform central reflection is traversed by sets of horizontal white and dark lines. These two sets run mainly parallel to one another. Lines of one color are wavy in nature and often branch and run together. Large areas of the crystal surface show no evidence of these lines whatsoever. The lines are interpreted as being due to low angle boundaries in the crystal, separating regions which are tilted with respect to one another. A white line is formed when the relative tilt forms a ridge at the interface and a black line is found when a valley is formed. In a number of cases, the lines stop and start within the area of the reflection and often run into the reflection from the edge, corresponding to a low angle boundary starting from the edge of the crystal. The prominent lines run roughly parallel to the direction of growth of the crystal although narrow bands can run in a direction perpendicular to this; see Fig. 2. Although they may change their appearance slightly, the lines tend to occur in the slightly,Same place in the X-ray image and to maintain their rough parallelism when the crystals are reduced in thickness by etching. Thus the low angle boundaries can occur at any depth within the crystal. The appearance of the lines is unaffected by subjecting the crystal to rapid temperature changes, such as plunging into liquid nitrogen or rapid quenching from 620°C. From the width of the lines on the x-ray reflection, values can be found for the angular misorienta-tion of the two parts of the crystal on either side of a boundary. The values found run from 1' to 10' of arc, but values of UP to 20' have sometimes been found, e.g., the widest lines on Fig. 2. These mis-orientations are much less than those commonly found in crystals possessing a lineage structure. When a number of a and white lines occur, running in a roughly parallel direction across the image of a Crystal, the total misorientation corresponding to lines of one color is approximately equal to that corresponding to lines of the other color. The interpretation of the lines as due to low angle boundaries has been checked in a number of ways. Photographs taken with different specimen-to-film distances distinguish lines due to low angle boundaries from effects due to surface relief of the specimen. Normal Laue back-reflection photographs, taken with the beam irradiating an area of the surface showing a number of the lines, show white lines running through each Laue spot. Black lines are set to see by this method. X-ray photographs were also taken, using the set-up described by Lam-one et al.5 when the beam straddles regions giving rise to lines in the Schulz pattern, split reflections are observed within the Bragg spot. The misorienta-tions calculated from the separation of these reflections and that found from the widths of the lines on the schulz technique patterns show good agreement. An exposure was made with Lambot technique of an area of the crystal showing no evidence of low angle

Jan 1, 1956

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co. purchased the first pumpcrete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms.

Jan 4, 1954

By A. W. Ambrose, C. E. Beecher

It is the purpose of this paper to summarize data on unitization projects in Oklahoma and Kansas as obtained from replies to questionnaires sent out by the A. I. M. E. committee for these states. The information received indicates that unitization is growing rapidly in this area, but has not been in operation for a sufficient length of time to develop production history. It was impossible to obtain a record of all unitization projects in the time available. The magnitude of such projects is indicated by the fact that reports were received covering a total of 171,420 acres in Kansas and 49,350 acres in Oklahoma. Most of these units have been formed during the past 2 years, the greater number having been completed in 1929. It is anticipated that even more will be formed during the present year. The following important facts have been emphasized by answers to the questionnaire and discussion with various operators: 1. Unitization is growing rapidly, as evidenced by the number of units and the large total acreage now included in units as compared with practically no acreage 2 years ago. 2. Operators are convinced that unitization is reducing development and operating cost and they anticipate greater reductions as experience is gained in unit operation. 3. Producing units have not been in operation for a sufficient length of time to give significant production history from which to estimate the ultimate recovery of oil, but the general opinion seems to be that more oil will be recovered. 4. In view of the benefits to be derived from unitization, many operators are refusing to carry on wildcat operations unless a unit has been formed. If this attitude continues to grow there will be no large pools developed in Oklahoma and Kansas in the future except under unit control. Summary The following tabulation gives a condensed summary of the information received on unit operations in Oklahoma and Kansas, but does not include all units, because many were not reported.

Jan 1, 1930

By AIME AIME

TOTAL shipments of iron ore from the Lake Superior district totalled 21,672,410 long tons in 1933, according to a compilation in Skillings' Mining Review. The producers ranked as follows in order of output shipped:

Jan 1, 1934

By Walter Nummela

INTRODUCTION By the end of 1979 pellet productive capacity from the processing of low grade iron ores in the Lake Superior-District will total 86 million tons per year. Of that tonnage, 72 million result from the processing of magnetic ores such as taconite, about 6 million tons from the flotation processing of relatively coarse grained specular hematite, and 8 million tons from the processing of fine grained non- magnetic ores at Tilden. The Tilden flowsheet represents a break- through in the processing of this type of crude ore and hence is unique in the Lake Superior District (1). Operations at Tilden started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleve- land-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling- Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Other companies have conducted extensive pilot plant tests or are in commercial production in the processing of fine grained non-magnetic ore materials (2). Flowsheets and reagent schedules may be different for each particular application, but some of the problem areas in the processing of Tilden ores have also been experienced at operations such as the IOC Plant at Sept-Isles, at Lamco and at Bong in Liberia, and in pilot testing of Fabrica ores of Ferteco Mineracao in Brazil. With a grind of about 80-85% -500 mesh resulting in 50% of the particles in the concentrate being less than 15 microns, a discussion of the pro- cessing of Tilden type ores fits the topic of this workshop. There are very large tonnages of fine grained non-magnetic crude ores which exist throughout the Lake Superior District and other iron ore producing regions. These fine grained non-magnetic materials constitute an important source of iron minerals. Before going into specifics of the flowsheet, it is important to

Jan 1, 1979

By H. Sato, I. Matsuoka, T. Kawai, S. Hasebe

In a limestone mine, a large amount of slime is washed off in order to remove impurities such as clay minerals. A fine sized calcite is, consequently, wasted and freight for carring the slime to reclaim land is expensive. The separation of calcite from the slime has been investigated by the flotation process, using sodium oleate as a collector. A satisfactory flotation of calcite from the slime requires great amounts of sodium oleate, because sodium oleate is consumed by clay minerals. But, the amounts of sodium oleate required are reduced to half by adding suitable amounts of sodium silicate. After rougher and cleaner flotation, the concentrate containing more than 97% calcite is obtained with 70% recovery; thereby the amount of slime to be reclaimed is reduced to 40%.

Jan 1, 1976

By Paul F. Kerr, Raymond F. Robinson

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 * 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre Cambrian. THE Sunshine mine in the Coeur d'Alene district, Idaho, is well known for its silver-bearing veins but prior to the summer of 1949 had not been recognized as a possible source of uranium. At that time, during a geiger counter reconnaissance by T. E. Gillingham, R. F. Robinson, and E. E. Thurlow, high radioactivity was noted and radioactive specimens were collected from the footwall of the Sunshine vein.' The detection led to the identification of uraninite-bearing veins, since explored jointly by the Atomic Energy Commission and the Sunshine Mining Co. After the occurrence was noted, the geology of the uranium deposit was studied by the Sunshine staff, and a laboratory examination of the ores was conducted at Columbia University. Several types of laboratory work were undertaken. Differential thermal curves were made of selected siderite samples and results from many more were secured through the work of Mitcham.2 X-ray diffraction and X-ray fluorescence analyses were employed on uraninite, jasper, and siderite. Chemical analyses were made through the cooperation of the Division of Raw Materials of the Atomic Energy Commission. General Geological Features Several silver-bearing veins cut the overturned north limb of the Big Creek anticline as mapped by Shenon and McConne1,³ while the Osburn fault, a long-recognized regional feature about a mile away, marks the north boundary of the Silver Belt. The Sunshine vein, Fig. 1, has a south dip more or less parallel to the 60" axial plane of the fold and cuts rocks of the Belt. Series, starting with the Wallace formation near the surface, continuing downward through the St. Regis formation, and probably extending into the Revett quartzite which lies below the bottom or 3700-ft level. The limb of the anticline is locally modified by secondary folds, one being prominently exposed in the uranian area along the Jewel1 crosscut near the Sunshine vein. Crumpling of the limb resulted from compression which formed the anticline and probably preceded the faults in which the vein deposits accumulated. Evidence of drag along these faults points to reverse movement in the uranium-bearing area and elsewhere. This is true of major faults in the mine workings, and the majority of faults which can be mapped, as pointed out by Robinson.' The St. Regis formation, as measured in the mine, appears to have an initial thickness of some 2000 ft, but the apparent thickness due to thickening during folding is some 3400 ft. Along the Sunshine vein the purple and green rocks characteristic of the Wallace formation in the nearby Military Gulch section p. 37 of ref. 5) have been completely bleached because of introduced sericite. Hydrothermal solutions acting on the wall rock have substituted for the original color a pale greenish cast, although no pronounced mineralogical change has resulted, as Mitcham has observed.' The silver and the uranium depositions appear to belong to distinct epochs resulting from several periods of emplacement. Likewise, multiple periods of deformation account for the faulting. Uraninite is generally associated with silicification, while silver . mineralization accompanies carbonate veins. Rarely, uraninite may be found in a matrix of siderite. Ordinarily uraninite formed prior to ar-gentian tetrahedrite. Where clusters of veins form a stockwork, uraninite-jasper veins often favor one trend while tetrahedrite-siderite veins favor another. During deformation, brecciation of the St. Regis quartzite provided openings between broken rock fragments for precipitation from vein-forming solutions. Fractures due to major breaks were filled during the first stages of vein formation, while later deformation displaced the first veins and provided new channels along which further mineralizing solutions proceeded. The uraninite veins, as the first formed, have suffered fracturing, displacement, and segmentation. Uranian vein segments uncut by faults and more than a few feet in length are rare or nonexistent. Siderite veins are more massive and often extend without a break for tens and even hundreds of feet. In general they show much less segmentation. While the siderite is usually later, there is an overlap in the periods of deposition, some earlier siderite veins being extensively segmented in much the same way uraninite veins have been broken. Vein silica is more extensively distributed than the uranium and iron mineralization it carries. Along the vein course concentrations of uraninite frequently fade away and barren white quartz continues, the transition often occurring within a few feet along strike or down dip. An example appears on the 3700-ft level where a uraninite vein, see Fig. 2a,

Jan 1, 1954

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Sidney A. Swensrud

Much has been said and written about uneconomic and evil marketing practices in the oil industry, including such factors as loaning of equipment, price cutting and secret prices, commercial discounts, abuses of credit cards and coupon books, and so forth. It is not my purpose here to add to the discussion of those problems, but rather to attempt a discussion of some of the more basic factors in the general distribution economies of the industry. The economics of distribution in the oil industry cannot be regarded apart from the general economics of the industry as a whole. The attempt to regard them as separate has led many people into the fallacy of believing that the responsibility for the apparent evils in the marketing end of the business lay entirely at the door of the marketing end. Such a view fails to take cognizance of many underlying factors; we can only expect to understand the distribution economics of the industry if we understand its general economics. We must realize also that the oil industry today is essentially the gasoline industry. The oil industry may be said to have begun about 60 years ago. At the outset it was concerned chiefly with the manufacture and sale of kerosene, lubricating oils and greases. Gasoline was then a most obnoxious by-product. The early oil-marketing company was engaged almost exclusively in refining and marketing—it did not concern itself with production but bore the relation to it merely of a purchaser. It may be said that the urge of marketing development in those days, therefore, came from the refining and marketing end of the business. The raw material had not yet begun to exert its enormous pressure, nor had the producer of crude oil acquired a direct interest in the sale of the ultimate finished products. Since then great changes have taken place. With the development of the automobile came a vast new demand for the raw material from which gasoline could be made. No longer could the refining and marketing companies be indifferent to the source of that raw material, particularly in view of the pessimistic outlook then presented as to the probable quantity of oil in existence. And despite the complete overturning of those early estimates, made before the bounty of nature and the skill of

Jan 1, 1931

By D. J. Crouse, W. D. Arnold

The potential behavior of radionuclides released in an underground nuclear detonation to fracture copper ore for subsequent in-situ leaching and copper recovery was studied with regard to contamination of the copper product and hazards to operating personnel. The laboratory test results indicate that only small fractions of the radioactive fission products would be dissolved on leaching the ore. Tritium (as tritiated water) would be the dominant radionuclide in the circulating leach liquor, assuming use of a fusion explosive. The test results showed solvent extraction to have important advantages over cementation for recovering copper from the leach liquors. While the radioactivity of the copper metal product produced by either method should be extremely low, the solvent extraction process provides a more effective separation of copper from the radioactive contaminants and entails fewer radiation protection problems. For these reasons it is the preferred process.

Jan 1, 1976

By Will H. Coghill, Fred D. DeVaney

THE coercimeter, as its name implies, is an instrument for measuring the coercive force[+] of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub- sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. The turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1938

By M. C. Fuerstenau, D. W. Fuerstenau

Long-Chained aliphatic amine salts have been used for the separation of sylvite (KC1) from halite (NaC1) by flotation. It is puzzling how these two minerals, which are so similar chemically and crystallographically, can be separated by this method. Gaudin as postulated that the difference in floatability of halite and sylvite with salts of primary amines depends on ionic size: In the case of amine flotation, the cation would attach itself to the chloride. I have a speculation there, which I cannot prove, that the ammonium group, that is the –NH3 group in the amine, floats potassium chloride because the dimensions of this group as it has been measured in other compounds is almost identically the dimensions of the potassium ion, quite different from the sodium ion, and so it fits where potassium had been, in place of it and not attached to it.

Mar 1, 1956

By J. F. Myers

THE Tennessee Copper Company's operations are in the Ducktown Basin, in the extreme southeast corner of Tennessee. The ore is of the heavy sulphide type, the predominating sulphides being pyrite, pyr-rhotite, chalcopyrite and sphalerite. The gangue is a micaceous schist, with varying amounts of free quartz. The mining operation develops two classes of ore, each of which is concentrated by the flotation process in separate mills. Table 1 shows a typical analysis of the ore treated in each mill. TABLE 1.-Typical Analysis of Ore Treated Composition, Per Cent Mill Tons Capacity Cu Fe S Zn London 1,350 1.41 28.4 20.2 1.10 Isabella 850 0.69 44.7 31.6 0.31 LONDON MILL The London mill was built in 1922, with a capacity of 400 tons per day. This was gradually increased to 600 tons by 1926, to 900 tons in 1928, and to 1350 tons in 1938. Fig. 1 shows the crushing and grinding flowsheet in 1928, when the capacity was 900 tons; Fig. 2, the crushing and grinding flowsheet that was developed by 1938, for the treatment of 1350 tons per day. A comparison of these flowsheets reveals that this increase in tonnage, with a subsequent improved operation, was accom-plished with identically the same major equipment. Improving a concentrator's capacity, metallurgical results, and costs as time goes by is a commonplace practice, and is accomplished in various ways, depending upon the local conditions. The reason for presenting the data of how this was accomplished in the mills of the Tennessee Copper Co. is that a fast-running rod mill plays such an interesting role

Jan 1, 1940

By S. A. Hovanessian

Analytical solutions are obtained for calculating the pressure distribution in rectangular fields due to injection and/or producing wells located anywhere within the field. The field is assumed to be homogeneous with either constant pressure or no-flow boundaries. These solutions are extended to include the calculation of average reservoir pressure and permeability from pressure build-up curves. Numerical examples are given to illustrate the application of equations to practical problems. INTRODUCTION Pressure distribution analyses are of considerable importance in the field of reservoir mechanics. A number of papers dealing with this subject have appeared in the petroleum literature. perrinel in 1956 presented a summary of the methods available for pressure build-up calculations and discussed the applicability of each in some detail. More recently (1958), Hazebroek, et a1,2 discussed a theoretical method for obtaining pressure distribution in a radial field. Also in 1958, Nisle3 gave a theoretical solution of the pressure distribution in a field extending to infinity with a partially penetrating line source at the origin. Mathews, et a1,4 applied the method of images to existing solutions for pressure distribution in radial fields and obtained expressions for calculating pressures in bounded reservoirs. However, a literature survey revealed that a general analytical solution for the pressure distribution in a rectangular field, with injection and/or production wells located anywhere within the field, was not available. Such a solution could be used to approximate the pressure distribution in a field the shape of which is nearly rectangular. Furthermore, it could be applied to pressure calculations pertaining to a single well taken from a system of wells which were drilled in a rectangular pattern. In this case the boundaries of the well drainage area are considered to be the perpendicular bisectors of the lines joining the well and its nearest neighbors. The basic problem considered in this paper consists of a rectangular field with either constant-pressure 01 no-flow boundaries and with either an injection or production well located anywhere within the field. The physical properties of the rock and fluids present are considered to be constant. Analytical expressions are obtained for the pressure distribution within the field during the production or injection periods. These expressions, which are infinite series, can be used to evaluate pressure at any point within the field as a function of time and position. For fields containing more than one well (production and/or injection), the solutions for each well acting independently are superposed. That is, at any point in the field, the pressures due to each injection 01. production well acting alone can be algebraically added to give the pressure resulting from all wells acting simultaneously. Evaluation of the series solutions given in this paper is readily accomplished by means of an electronic digital computer; and, in most cases, sufficient accuracy is obtained by setting the upper limits of summation at 20. These solutions are extended to include the calculation of average reservoir pressure and permeability from build-up data. A number of numerical examples are given to illustrate application of the solutions to actual field problems. ANALYTICAL SOLUTIONS The partial differential equation representing the pressure distribution in a homogeneous rectangular field (see Fig. I.), having a single source or sink of strength (2, can be written*

By A. F. Witt, A. M. Gaudin, A. K. Biswas

Finite contact angles in the rutile-water-organic liquid system are traceable to contamination or are due to addition of a surface-active agent. Finite contact angles are invariably accompanied by hysteresis.1-7 Besides surfactant concentration and pH, the nature of the organic liquid is found to be a factor influencing the magnitude of contact angle hysteresis. In a recent paper the authors have reviewed principles and applications of measurement methods for contact angles and their hysteresis.22 In this paper, these methods are applied to a system consisting of rutile, an organic liquid (benzene, decane, or dode-cane) and water. Surfactant (dodecylamine hydro-chloride) was used at various concentrations and various pH values. MATERIALS A synthetic rutile crystal supplied by the Linde Co. was used. It is a cylinder 1/2 in. diam, with faces cut perpendicular to the c-axis. The crystal is stated to be alumina-free and to be 99.9% pure. Rutile is a high surface energy solid, its calculated average field strength being 2.7 x 105 e.s.u.,9 its dielectric constant10 is 114. The zero point of charge of rutile was measured11 and found to be at pH 6.0. The atomic distances and bond angles of the tetragonal crystal of rutile have been precisely determined.l2 The organic liquids were specially purified. Reagent grade benzene was repeatedly shaken with concentrated sulfuric acid to remove thiophene, then neutralized with sodium hydroxide solution, rinsed with distilled water, dried overnight over anhydrous calcium chloride and filtered. The refractive index of this chemically purified benzene was 1.4977 (at 25°C) - very close to that of pure benzene (n25 1.4979).13 Both n-decane and n-dodecane were washed with aqueous sodium hydroxide, concentrated sulfuric acid (repeatedly, until the acid layer was colorless) and again with alkali, to free the organic hydrocarbon from fatty acids and unsaturated hydrocarbons. The organic phases were subsequently washed with distilled water and dried over anhydrous sodium sulfate. The filtered hydrocarbons were then distilled under vacuum (9-10 mm pressure). Decane, thus purified, showed traces of unsaturated and of carboxylic compounds. On gas chromatographic analysis the purified n-dodecane showed the presence of two impurities. However, the relative retention times of these components did not change substantially when measured on a polar or a nonpolar column. This indicates that the compounds were probably in the same polarity class, i.e. the components were nonpolar like dodecane. Conductivity water has always been one of the liquids. Conductivity of the water used was 10-6 ohm-' cm". Dodecyl ammonium chloride was prepared from pure amine (supplied by Armour and Co., Chicago), by Li in the MIT Mineral Engineering Laboratory.14 The critical micelle concentration at 25°C is known, 0.0138 mol per liter15 or 3.06 gpl. All our experiments have been done at concentrations lower than the critical micelle concentration. The glass vessels, glass drop holder and the rutile crystal were all cleaned with hot chromic acid followed by distilled water, concentrated hydrochloric acid, and again distilled water, and conductivity water. During the experiments, a nitrogen atmosphere was maintained. For this purpose, commercially purified nitrogen was further purified by passing it over hot copper wire at 450°C, then through columns of acidic chromous chloride solution, concentrated alkali solution and distilled water. APPARATUS AND METHODS Hysteresis was produced by the "captive drop" or constant volume drop method as well as by the "expanding-contracting drop" or variable volume drop method. The image of the drop while it is expanding, contracting or moving is projected on a screen and photographed. The developed film is projected through an enlarger and the contact angles measured with a protractor.

Jan 1, 1964

By Edgar Rickard

IT SHOULD be clearly understood that my remarks on economic conditions in Russia are entirely personal, and not official as an officer of the Ameri-can Relief Administration. The American Relief Administration is concerned exclusively in relief operations. The American Relief Administration has played a large part in the conditions as they exist in Russia today and it does not seem to be out of order to give you the high lights of the work accomplished. SIXTY MILLION DOLLARS FOR RUSSIAN RELIEF The Riga Agreement, by which we were enabled to carry on our operations, was signed in Riga on Aug. 20 of last year. On Sept. 8, we opened our first relief station in Petrograd. On Sept. 18, our first food was handed out in Samara on the Volga River, in the center of the so-called famine district. Altogether over 775,000 tons of food have been sent from the Atlantic Coast into Russia and we have moved this entire quantity of food over a dilapidated and wornout system of railways; and we estimate that our loss will be less than one-half of one per cent. in shortages and thefts. We have had available for this Russian work approximately $60,000,000. The bulk of this money was derived from a Congressional grant of $20,000,000 for food stuffs, a further Congressional grant of Army medical surplus supplies of $4,000,000, a grant by the Soviet Government of $11,400,000. This Soviet grant is a rather interesting phase of our operations. In all of Mr. Hoover's relief work abroad he has demanded of the country receiving relief that the people them-selves do something concrete for their own good before he would undertake to collect large sums of money in America. Secondly, before he was willing to go before Congress and ask for funds from our government he desired that the Soviet Government show their good will.

Jan 11, 1922

By G. R. Leverant, C. P. Sullivan

Re crystallized TD-nickel mi-2Th0,) in both coated und uncoated conditions was fatigued at 1800°F at total strain ranges varying .from 0.2 to 0.75 pct. The fatigue life of uncoated inaferal, Nf, was related to the total strain range, ?eT, by (2Nf/021AeT = 0.014. A duplex Al-Cr pack coating increased the fatigue life by about a factor of two. The cracks that led to failure in both coated and uncoated material were initiated at the outer surface, indicating that the mechanical properties of the surface layers were important in determining fatigue life. Crack propagation and subsurface crack initiation in the TD-nickel occurred preferentially at grain boundaries with cavitation at thoria particle-matrix interfaces an integral part of the grain boundary fracture process. The importance of both the grain morphology developed during thermome chanical processing of TD-nickel and the distribution of thoria particle sizes to fatigue resistance are discussed. THE fatigue properties of only a few dispersion-strengthened metals have been studied at temperatures 0.5 Tm;1,2 among these have been lead and aluminum containing oxide dispersions. TD-nickel is a material of interest for application in aircraft gas turbine engines, but little fundamental information is available on its behavior under cyclic loading conditions. In this study, the low-cycle fatigue properties of TD-nickel were determined at 1800°F with emphasis on the 101-lowing; 1) the relation of the grain morphology produced during thermomechanical processing to crack initiation and propagation; 2) the role of thoria parti-cles in the fracture process; and 3) the effect of an oxidation resistant coating on fatigue life. I) MATERIAL AND EXPERIMENTAL PROCEDURE The TD-nickel was supplied by DuPont as a 5/8-in. thick plate which had been subjected to a proprietary series of thermomechanical treatments with a final anneal at 2000°F for 1 hr in hydrogen. The composition of the material is given in Table I. At the test temperature of 1800°F, the 0.2 pct offset yield stress was 15,000 psi, and the elongation and reduction in area were 4.6 and 3.0 pct, respectively. The microstructure of this material has been previously described.&apos; Briefly, it consists of an array of lath-shaped grains, about 0.15 mm in thickness, with the long dimension of each grain parallel to the primary working direction, Fig. 1(a). The presence of very small annealing twirls, Fig. l(b ), together with the absence of extensive dislocation networks, Fig. L/C), indicated that the material was in the recrystal- Table I. Composition of TD-Nickel ThO2 2.3 vol pct C 0.0073 wt pct lex 0.01 wt pct Cr 0.01 wt pct Cu 0.004 wt pct S 0.001 wt pct Ti <0.001 wt pct Co <0.01 wt pct Ni bal lized condition. Commercial TD-nickel sheet has a similar grain size and shape, but unlike the present material is not recrystallized as evidenced by the absence of annealing twins and the presence of a well-developed dislocation substructure.4 The plate material had Young&apos;s moduli in the rolling direction of 22 x 106 psi and 13 x 106 psi at room temperature and 1800°F, respectively, indicating a texture with a strong {100}<001> component in agreement with previous observations on recrystallized TD-nickel sheet.596 The 2.3 vol pct of thoria particles were uniformly distributed although some clustering and stringering of larger particles was occasionally seen. The average diameter of the particles was 450 and the calculated mean planar center-to-center spacing was 2100Å. Two specimens were coated with a duplex A1-Cr pack coating. The coating was somewhat nonuniform from one position to another along the gage length. An area of the coating after testing is shown in Fig. 2. Electron microprobe analysis revealed the following zones in the various lettered regions indicated in Fig. 2: A) a bcc matrix of B-NiA1 with some chromium in solid solution along with a fine dispersion of a chromium-rich second phase which was probably precipitated during cooling from the test temperature to room temperature; B) fcc y&apos;-Ni,Al with some chromium in solid solution; C) porosity; D) a two-phase mixture of a chromium-rich solid solution containing nickel and aluminum and a small volume fraction of a nickel-rich solid solution having approximately the same composition as the immediately adjacent portion of region E, E) the TD-nickel substrate containing chromium in solid solution to a depth of 5 to 10 mils. As expected from the nature of the diffusion processes involved,7 the thoria particles were present only up to the layer of porosity, region C, Fig. 2. The measured thickness of the coating proper, zones A to D, after testing was 1 to 2 mils. The specimen design and testing techniques have been previously discussed.&apos; Stressing was axial and parallel to the lath-shaped grains (i.e., parallel to the rolling direction). The total strain range was controlled between zero and a maximum tensile strain varying from 0.2 to 0.75 pct. (The test at 0.2 pct total strain range was switched to load control at 1030 cycles at which point the peak tensile and compres-

Jan 1, 1970

By R. J. Charles

SEARCH for a consistent theory to explain the relationship between energy input and size reduction in a comminution process has accumulated, over the years, an enormous amount of plant and laboratory data. Although some correlation of these data has been possible for purposes of engineering design and for the advancement of research in fracture, there is still great need of a means of predicting behaviour of a solid when it is reduced in size by mechanical forces. The best known hypotheses proposed to describe the energy-size reduction relationships in crushing and grinding stem from a common origin. The present article analyzes problems of comminution in the light of the precepts of this origin. Its object is to reconcile points of difference between these well known hypotheses and to present relationships more widely applicable to comminution studies. Theoretical Considerations: Most existing relationships between energy and size reduction of a brittle solid stem from a single, simple, empirical proposition.&apos; Although this proposition can be demonstrated by observation and experiment, no theoretical derivation is yet possible. Mathematically, the proposition may be stated as follows: dE = -Cdx/xn [1] where dE = infinitesimal energy change, C = a constant, dx = infinitesimal size change, x = object size, and n = a constant. Eq. 1 states that the energy required to make a small change in the size of an object is proportional to the size change and inversely proportional to the object size to some power n. No stipulations are placed on the exponent n in either magnitude or sign. In 1867 Rittinger2 postulated that the energy required for size reduction of a solid would be proportional to the new surface area created during the size reduction. As far as can be determined there is as yet no physical basis for Rittinger&apos;s hypothesis. Rittinger&apos;s hypothesis can be stated mathematically as follows: E, = K(oa-a-0 . [2] Er = energy input per unit volume, K = a constant, <ti = initial specific surface, and o2 = final specific surface. In the size reduction of particles of size x, to particles of another smaller size, x2, Eq. 2 becomes the well known relation: ET = K&apos; {l/x2-l/xx) [3] where K&apos; is a constant. Eq. 3 may be arrived at from the proposition given in Eq. 1 by integrating and by assigning a value of 2 to the exponent n. J dE = J - C dx/x2 E = Kt (1x - 1x) where K&apos; = C. In 1885 Kick3 proposed the theory that equivalent amounts of energy should result in equivalent geometrical changes in the sizes of the pieces of a solid. For example, if one unit of energy reduced a number of equal-sized particles to particles of one half the size, then the same amount of energy applied to the particles resulting from the first test should result again in a size reduction of one half or a final size one quarter the original size. The Kick concept may be expressed as follows: Ek = K" log x1/x2 [41 K" = a constant and E, = energy per unit volume. The expression for Kick&apos;s law may be arrived at by again integrating Eq. 1 and in this case assigning a value of 1 to the exponent n. dE= J - C dx/x Eh = - C In {x/x2) = K" log (x,/x,) where K" = 2.3 C. Application of Kick&apos;s and Rittinger&apos;s laws to comminution has met with varied success. Gross and Zimmerley4 and Piret5 have shown that Rittinger&apos;s equation applies under certain conditions of experimentation. Walker and Shaw6 express the belief that in metal turning and shaping and in grinding of both metals and minerals the production of very fine particles (less than lP) follows Kick&apos;s hypothesis, whereas Rittinger&apos;s concept is valid for the size reduction of coarse particles. For the practical case of crushing and grinding, however, neither of the above hypotheses has received general acceptance. Bond&apos; has lately proposed that since neither Kick&apos;s nor Rittinger&apos;s hypotheses seem correct for plant design work, an energy-size reduction relationship somewhere between the two would be more applicable. The fundamental statement of Bond&apos;s work

Jan 1, 1958

By D. D. McNaughton

IN providing 65,000 tons of broken muck per day for shovel operation in a large open pit copper mine, drilling equipment and efficient use of that equipment is of prime importance. To improve existing drilling efficiencies, a large electric rotary drill capable of drilling 12-in. holes was purchased in May 1955. At Chino 96 pct of the blasting is done with 12-in. holes because: 1) the large holes break the optimum amount of material to reduce trackshifting to a minimum, 2) better fragmentation is obtained from a relatively short column of powder, and 3) longer spacing results in greater tonnage broken per foot drilled. From 1955, when it was purchased, through October 1956, the rotary drill has drilled 95,701 ft at a rate of 167.4 per shift in various locations and types of ground encountered in the mine. (This includes moving time and all other delays while a crew is on the machine.) The machine has been worked two shifts per day, seven days per week, and has been available 68 pct of this time.

Jan 5, 1957