Search Documents

By B. A. Shaw

Historically, microwave tubes have been fabricated from massive metal and ceramic components. The current trend is to lighten tibes for airborne applications. The reqciiremenls of light weight and also reduced cost have created a novel approach to tube structure in which thin-film technology plays a major role. Although the electrical requirements of thin-film circuits in microwave tubes differ from those required or se,niconductor integrated circuits. the technology is basically similar. The stringent requirements of the micvowave tube have created sophisticaled thin-film techniques thut are of interest to the integrated-circuit industry in general. This paper describes a nunzber of thin-jilm techniques recently developed and discusses in detail the application of the technology in microwave tubes. The particular areas of interest are: 1) ceramic mounted thin-film slow-wave structures; 2) thin-film secondary emitters; 3) suppression of tube environnental multipactor by semiconducting' thin films; and 4) age-hardenable and dispersion-hardened thin metal films. SEVERAL thin-film techniques specifically applied to microwave power tubes are discussed in this report. There are two reasons for this work. One is the necessity of reducing weight and cost of microwave tubes and the other is related to overcoming problems in the tube operation by the use of applied thin-film technology. The major emphasis of this work has been on tube slow-wave structures. Other work in the area of secondary emission, either its suppression or its enhancement, is continuing; the most satisfactory results to date have been by utilization of thin-film technology. The requirements of high thermal and electrical conduction together with greater strength than normally obtained with elemental materials have led to the development of dispersion-hardened films. The paper will discuss: 1) ceramic-mounted delay-line microwave tubes; 2) multipactor and secondary emission; 3) hardened films. I) CERAMIC-MOUNTED THIN-FILM SLOW-WAVE STRUCTURES In a conventional crossed-field microwave tube, the slow-wave or delay-line structure is produced from two carefully machined components. One half of the structure is shown in Fig. 1. The other half is the mirror image of the first but is rotationally offset by a half a period. The combined structure now forms an interdigital type of slow-wave structure and is the anode of the tube as shown in Fig. 2. The period and finger length of an interdigital slow-wave structure are prescribed by the desired dispersion characteristics. The typical design is as shown in the first figure; it can be noticed that the finger width is several times greater than the finger thickness. Even assuming that it were mechanically possible to produce free-standing fingers of extremely small cross-sectional dimension, for example, 0.002 in. thick by 0.005 in. wide by 0.500 in. long, decreasing this finger width would increase the tube efficiency but would also decrease the thermal-conduction path, causing an increased temperature rise from intercepted rf current which in its extreme could easily cause finger melting. Hence, for free-standing lines of this type, the design is a compromise between mechanical capabilities, tube efficiency, and thermal dissipation. These structures are also expensive and tend to be heavier than purely electrical considerations would demand. In the present approach, we have transposed the three-dimensional structure previously shown into an essentially two-dimensional structure as shown in Fig. 3. The linear structure is used here for clarity of detail. The support member is a ceramic material and the line is deposited copper. The final tube design is shown in Fig. 4. Because of the backwall sup-

Jan 1, 1967

By Richard Franchot

From an efficiency viewpoint, the greatest loss of energy to the blast furnace is in its failure to convert more than about a third of the coke carbon from carbon monoxide to carbon dioxide. This result has usually been ascribed to a necessity of a 2:1 excess of CO in order to reduce iron. It has, however, been proved that iron is completely reduced by equal volumes of carbon monoxide and carbon dioxide. Hence there is room for the hypothesis that vaporization, as cyanid, of accumulated alkalis is a serious primary factor limiting the ratio of ore to coke. Observed cyanid vapor concentrations and those measured by the variations of the nitrogen-oxygen ratio in the hearth gases form the basis for a quantitative explanation of the furnace action. As EVERYBODY knows, the blast furnace is a gas producer. As to the reason for this, people are not so well agreed. The significance of the fact is obvious, for the extent to which the fuel leaves the furnace as combustible gas measures poor economy in iron smelting; while good efficiency in this respect means poor gas. The furnace thus works at cross purposes. The present trend of the steel industry is toward. a primary use of the blast furnace as a gas producer with pig iron as a byproduct. Needless to say, this trend is away from improvement in iron making. The production of more and better iron in a given furnace consuming a given amount of coke would seem, at least, to involve a decrease in the relative proportion of the combustible gas. The possibility at the same time, however, of making more and better gas need not necessarily be excluded. (The more the furnace acts as gas producer, the bigger is the sulfur problem.) Whatever the object, it would seem desirable to have a, clear, comprehensive, mathematically exact estimate of why and how the blast furnace functions, to the large degree that it now does, as a gas producer. The literature does not give a definite answer to the question. That for which explanation is sought is the fact that only a minor part, usually not more than a third, of the coke carbon burned is oxidized to carbon dioxide; that the development in the furnace of the fuel energy is thus limited usually to little more than 50 per cent.; that it requires about twice as much fuel coke to make a ton of iron as is indicated by the rela-

Jan 7, 1925

By D. W. Philips

THE problem of strata control has of necessity been prominent in mining, and accounts of individual experience and research abound in the literature of most mining countries. Organized research began in Britain by the formation of a committee, upon the recommendation of the Safety in Mines Research Board in 1923, to investigate methods of reducing accidents from falls of roof in coal mines. This committee examined current practice in supporting underground workings in the principal coal fields, and its findings have been published in the Board's publications. Toward the end of these investigations it was suggested by the Chief Inspector of Mines that committees of the several mining institutes be formed to examine the problem in their respective districts. The formation of these committees marked a new phase in research on strata control. The work, though being done in the separate coal fields, followed a scheme outlined by the Chief Mining Engineer of the Research Board, and was coordi¬nated by his office. FACTORS INVOLVED The subject is being considered in Britain from two aspects: I. To provide, by supports, means to prevent falls of fractured ground. 2. To develop methods whereby the strata can be maintained in the least broken condition and thus make falls less likely. The first aspect is the one that will most likely lead to immediate results from the accident standpoint. It depends largely upon the assimilation of already acquired knowledge regarding the proper¬ties of supports and their correct applica¬tion. The second aspect is perhaps more fundamental, and involves also the proper¬ties of the strata and their behavior under the influence of the forces induced by mining. The problem involves many natural factors that cannot be controlled, such as depth, inclination and thickness of seam and nature of the rocks. Other factors, which may be considered to a certain extent controllable, cannot be varied readily and with sufficient fre¬quency to facilitate easy investigation; some of these are: rate of advance of the working face, length of face, direction of the face with regard to cleat and inclination, system and arrangements of rock packing behind longwall faces. In any given case the very many factors present have a mutual influence upon the effects produced in the mine. For example, a study of the effects of rate of advance cannot be done without considering the effects of other factors such as nature of strata, direction of face and quality and arrangement of supports. Conversely, the length and direction of a working face

Jan 1, 1946

By W. G. Pfann

WHEN a molten zone traverses a long, solid ingot in a level, open boat the ingot becomes tapered. While the taper may be slight after one zone pass, it can be appreciable after repeated zone passes, even to the extent of causing an overflow of matter at the end of the boat. It will be shown here that such matter transport by a molten zone arises from the volume change on melting and that it corresponds in magnitude and direction to the magnitude and sign of the volume change. It will be shown also that the mechanism of matter transport is basically similar to that of solute transport by a molten zone, which has been discussed elsewhere,1,2 and that the two processes can be described by similar equations. Finally it will be shown that matter transport can be prevented by inclining the ingot at a critical angle. Contraction on melting results in forward transport, that is, transport in the direction of zone travel; expansion on melting results in reverse transport. The way in which forward transport arises from the contraction on melting may be seen as follows: At the starting end of a solid horizontal ingot of uniform rectangular cross section of height h., form a molten zone of length 1, as shown in Fig. 1. The height h of the liquid will be h. where a is the ratio of density of solid to that of liquid. Advance the molten zone, at constant length, a distance dx. The volume of solid melted will be hdx; the volume of solid frozen will be Izdx, because the height of the freezing solid will tend to be equal to that of the liquid. The resultant change, dv, in liquid volume will be the difference in these quantities multiplied by the density ratio. Hence the following equation may be used for a zone at any distance x from the origin: which is valid in all but the last zone length in the

Jan 1, 1954

By G. S. Brooks

(New York Meeting, February, 1913.) THE tendency of the oxides of such metals as aluminum, zinc, chromium, and calcium to form compounds at high temperatures with iron oxide is well established by past investigation. Data of this reaction, as developed in laboratory research, have been contributed by Burleigh, Hofman, and Wells, in America, and by many others abroad. A partial bibliography of the subject is appended. From these authorities we learn that the ferric oxide here has the function of an acid, giving in the case of ZnO a zinc ferrite, with a normal composition of ZnOFe2O3. This formation of zinc ferrite particularly affects the success of such processes as leaching or magnetic separation, and thus becomes practically important to the metallurgist. But the meager existing data do not entirely agree; and quantitative results from muffle-practice are conspicuously absent. Furthermore, it being of some general importance to the zinc smelter in both roasting and reduction, the following few notes of operations on a commercial scale are contributed

Jan 5, 1913

Jan 1, 1951

By W. J. Keep

We have shown in former papers the influence which aluminum exerts when added to cast-iron, and we have presented in another paper, accompanying this one, the physical properties of the metal aluminum and of some of its alloys. The present paper continues the investigation. The reader will find, in our paper on "Aluminum and Other Metals Compared,"* explanations not here repeated, which will render the diagrams in this paper intelligible. The scale of stresses is laid off on the ordinate which rises from the zero-point of the diagram. The scale of deflections is laid off on the abscissa which runs horizontally through this zero-point. By applying a given amount of stress, then running back to zero, and again applying the same stress, we describe a spring-line, in which the deflections are proportional to the stresses. Generally the deflections exceed this proportion during the original application of stress; and the excess is the permanent set. By laying off from the zero-point a line parallel to the springline, we shall generally find that this new spring-line and the diagram coincide for some distance; that is, that the test-bar is

Jan 1, 1890

By Guy W. Jordan, David P. Hale

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By David P. Hale, Guy W. Jordan

High-iRon cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper"burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to"freezing and thawing, and increases the resistance of the cement to sea "or sulphate waters. [" During the past few years the construction of numerous dams through- "out the Southeast by the Tennessee Valley Authority has stimulated the "production of high-iron cements. At present a great number of specifica- "tions call for an iron cement, and the industry is supplying this demand "with a Portland cement carrying approximately 5 per cent iron oxide. "Several manufacturers are now making practically all of their cement "of this type and a number of others manufacture it as a special cement "over short periods to meet demands from the Tennessee Valley Authority "and other buyers. " The recent increase in the use of iron in Portland cement has created "a market for iron products that previously was nonexistent. The chief "sources of supply for the cement manufacturers at present are iron sand, "iron sinter and slag, and ocher. The Copperhill mining district, Ten- "nessee, supplies both iron sinter and slag for use in cement. The Carters- "ville district supplies iron sand, ocher, and some iron resulting from the "magnetic separation of iron from barite. The advantages of these "products vary according to the chemical properties of the raw materials "and the methods of handling used by the different manufacturers. Where "the iron is to be handled by conveying belts and in hopper cars, the iron"sand and sinter and slag are preferable. Where the silica content must "be raised, the iron sand is doubly advantageous because it supplies both

Jan 1, 1942

By Terje Preber

Undisturbed sampling of shale has always been difficult. As pert of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois, the Maquoketa shale, which contains seams of argillaceous dolomite, was sampled using different coring techniques. Since the Maquoketa shale is extremely fissile, careful sampling preservation by both lateral and vertical confining was utilized. The samples were tested to determine both static and dynamic properties. A relationship between void ratio and compression index, swell index, and swell pressure ratio was established. Correlation was found between the dynamic properties and both undrained shear strength and confining stress. Based on the results of the sampling and testing programs, recommendations for sampling and sample preservation techniques are given. INTRODUCTION Undisturbed sampling and preservation of samples of weathered, fiasile shale is often a very difficult task. The often erratically varying degree of weathering with depth complicates sampling and makes reproducibility of testing results difficult. Therefore, the testing of weak, weathered rock very often yields a wide variety of test results with large data scatter. The reproducibility of teat results usually associated with water-deposited soils is seldom, if ever, obtained. The testing and sampling program described in this paper was part of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois. The sampling, preservation and testing program of shale samples taken from the Maquoketa shale are described, and, in particular, the different sampling techniques and sample preservation procedures are evaluated with respect to their effectiveness. The samples obtained by these procedures were subjected to a comprehensive testing program, including both static and dynamic testing in order to provide input for soil-structure interaction analysis. GEOLOGY The Maquoketa Shale Group is of Ordovician age and is part of the Cincinnatian Series. The area where the shale samples were taken was in a broad sea far from sources of clastic sediments during most of Ordovician time. However, during Cincinnatian time when large deltas in the Appalachian region were being formed, clastic sediments from the east dominated the sedimentation ii. Illinois, resulting in formation of the shale and dolomite shales of the Maquoketa Shale Group (Willman et al., 1975). The geologic unit sampled consists of a greenish gray to gray silty shale containing numerous 1- to 12-inch (2.5- to 30.5-cm) thick interbeds of argillaceous dolomite. The dolomite comprises up to 40 percent of the profile studied. The shale

Jan 1, 1984

By W. A. Hoyer, G. A. Lock

Laboratory and field tests have shown that it is feasible to log for copper in a qualitative way using the techniques of neutron activation analysis. Laboratory tests showed that the 0.51 and 1.04 mev gamma rays of 62Cu and 66Cu, respectively, could be diagnostic. However, in the core holes, the detection of copper was limited to 0.3% concentration because of interferences from the 18Si and Al gamma rays. Both stationary and continuous logs were made, but only the stationary data yielded a recognizable copper response. This response consists of a combination of two effects-the direct response from copper at 0.51 mev and an increase in low energy gamma ray absorption due to mineralization. Both low energy chemical (PuBe) and high energy accelerator neutron sources were used for the laboratory and field tests, while the same 2 X 5 in. Nal scintillation detector served for all the tests. Potential improvements in copper detection might be possible with solid state gamma-ray detectors which have better gamma ray resolution but much less detection efficiency. This type of activation logging requires complex equipment and trained personnel to conduct field operations and may find application where coring is difficult or prohibitive.

Jan 1, 1973

FOLLOWING the presentation at the annual meet-ing of the paper "Recent Developments in Classi-fication," by A. M. Gaudin and W. L. Remick, the discussion presented below took place: H. N. Spicer : I haven't been able to study this paper closely, but I would like to ask 'Mr. Remick something regarding the work done by the mechanical classifier. The screen test given here would appear to show that the classi-fier did very, very poor work. The 44 per cent efficiency calculated from this equation is much lower than any ordinary operation. Nothing is stated regarding the de-tails. of the operation, the slope of the classifier, the dilu-tion, the speed, and such other factors that influence results. I would also like to know something of the material that was worked. The Manhattan schist that I have seen them digging out of the subways is of a flaky nature, so that in any classifier, you might get the factor of fine flakes floating over. Was the same material used in the hydrotator test? The screen tests vary a whole lot. Mr. Remick: You will notice the Dorr classifier han-dled the circulating load. This classifier naturally was run in closed circuit. I should like to be pardoned for quoting from Mr. Bates' paper of last year on "Classifica-tion in the Witwatersrand Mills." In this report only two efficiencies were given for the so-called straight type Dorr classifier. One was 44.6 per cent and the other 61.6. I don't know whether or not an average should be taken for the proper performance. I assume that that test was performed under better conditions, yet the efficiencies av-eraged only 53.1 per cent. I am afraid I am taking the words out of Professor Taggart's mouth, but he has told me that the Dorr classi-fier at Columbia is not the proper size to work with the Hardinge mill with which it is connected. This indicates only the inadvisability of putting commercial sized mat chines in a school laboratory. You cannot, he says, get the proper tonnage from the Hardinge mill to work the Dorr classifier and get the best results. Mr. Bates' results show higher efficiency with the lower capacity. Now, on the other hand, I assume that the classifier described in Mr. Bates' paper was probably run at the proper capacity.. It is a rather puzzling question.

Jan 4, 1927

By Brison Robertson, W. P. Fishel

THE carbide-forming tendencies of the various steel-alloying elements, or their affinities for carbon, is a subject that has received considerable attention, but little more than a probable arrangement of the elements as to their carbide-forming tendencies has been proposed. The physical properties of alloy steels depend upon the relative proportions of the elements present and their combinations. One important phase of this subject is the distribution of carbon between the various elements present. The distribution of carbon between iron and other elements evidently will depend upon: (I) the affinity of each for carbon; (2) the relative atomic masses of the elements present; and (3) the possible formation of compounds between the alloying elements and iron and between the elements themselves. In ternary steels the case is simplified, especially in systems in which the element and iron form no compounds. In such systems iron and the alloying element are competing for the carbon present. In this work the distribution of carbon between titanium and iron has been studied by measuring the relative amounts of iron carbide and titanium carbide present in a series of annealed steels in which the ratio of titanium to carbon extended from 0.527 to 4.61. EXPERIMENTAL PROCEDURE Ten Fe-Ti-C alloys, weighing about 250 grams each, were prepared by melting under a vacuum, in an induction furnace, Armco iron, carbon-free ferrotitanium (25 per cent Ti), and pure carbon. Vacuum melting prevented the formation of titanium oxides and nitrides, which would complicate the problem. The melts were made in graphite crucibles lined with sintered magnesium oxide. The ingots were cooled in the furnace under a vacuum and were then completely annealed at 950°C. The determination of the amount of titanium carbide present was based upon the established insolubility of titanium carbide in boiling dilute (I :4) sulphuric acid, and the complete solubility of free titanium and titanium-iron compounds in this acid. High-carbon ferrotitanium, which had been treated to remove free Ti and Fe, was found to be completely insoluble in the acid; and the carbon-free ferrotitanium used in making the alloys was found to be completely soluble. Others 1,2 have reported the insolubility of titanium carbide in sulphuric and hydrochloric acids. Turnings from the ingots were digested with boiling sulphuric acid (1:4) until all action had ceased. The carbide residue was filtered off and analyzed for titanium, and in some cases for carbon. This represents the titanium that was united with carbon. The filtrate from the carbide residue contains the portion of the titanium that wasin solid solution in the ferrite. Titanium

Jan 1, 1944

By A. W. McReynolds

One characteristic of plastic deformation which distinguishes it from elastic strain is the essential inhomo-geneity of plastic strains. Elastic strain varies continuously through a material, and average relative displacements of initially adjacent atoms are only small fractions of their initial spacing, (strains of the order of 0.01 or less). On the other hand, plastic flow corresponds to the appearance of discontinuities in strain of the lattice, such as dislocations or slip bands, where local strain, on an atomic scale, is several orders of magnitude higher. These discontinuities are visible on a microscopic scale as the familiar slip lines (Fig 1). In spite of this obvious microscopic inhomogeneity, however, macroscopic measurements almost invariably show a smooth curve of stress vs. strain (Fig 2b) even if measurements of linear strains be made to an accuracy of one part in 107. This macroscopic homogeneity of strain indicates that the discontinuities in strain on slip planes occur in increments too small or too slow to be recorded individually, and further that they occur sufficiently independent of one another so that the small increments add at random to a smooth stress-strain curve. The present paper describes observations of plastic strain in aluminum of commercial purity and in high purity Al-Cu alloys, where there exists a strong coupling between slip in various regions of the specimen such that once initiated it spreads rapidly through a large volume. The total effect is that of relatively large, rapid, and regularly spaced steps of strain followed by periods of only elastic strain. Fig 2a illustrates the type of "stair-step" stress-strain curve which results. The properties of this cooperative slip phenomenon will be described further in the section on results: in par- ticular it will be shown that each step corresponds to the propagation of a wave of plastic deformation through the specimen. Some interpretations of the mechanism by which it occurs will be made in the following section. Although the type of plastic wave phenomena to be described has not previously been reported, there are numerous cases of related effects in the plastic yielding of metals: YIELD POINT PHENOMENA The most familiar of such effects is the "yield point" observed in low carbon steels, brass, duralurninum, and the like. It consists in the sudden termination of the elastic portion of the stress-strain curve by a large plastic strain. Since the usual tensile machine is such that yielding of the specimen relieves the load, the resulting curve is as shown in Fig 3. As the strain continues, deformation occurs at a lower stress for some time, then follows a rising curve, but with no further sudden yielding. This effect has been observed in brass by Sachs and Shojil and later by many others. Edwards, Phillips and Jones2 made extensive studies of the effect in steel, and of the role of various alloying elements. Although there seems to be fairly clear evidence that the yield point is caused by a hardening of the material by precipitation of impurities, no satisfactory explanation for the sudden yielding has been given. Winlock and Leiter3 have shown that the strain. level of the upper yield point depends strongly on the rate of loading, the yield point increasing by almost a fac- tor of two as the strain rate goes from 0.002 in. per in. per min. to 4.4 in. per in. per min. This effect would seem to imply an incubation period before yielding is initiated at a certain stress. On the other hand, by going to very slow loading rates, Edwards, Phillips and Jones2 showed that the yield point does not become lower and eventually disappear as might be expected, but, on the contrary, begins to rise at loading rates below about 25 Ib per in. per min. becoming much higher than at rapid loading rates. STRAIN AGING If, instead of continuing straining of a specimen after occurrence of a yield point, the load is removed and the specimen aged, resumption of the test results in occurrence of another yield point as shown by the dotted curve of Fig 3. The new yield stress is generally higher than the previous maximum applied stress. This hardening of the material by straining and subsequent aging is undoubtedly related to quench age-hardening resulting from the aging of a specimen quenched from high temperature. Since neither effect is observed in pure metals, it is generally accepted that quench-aging in all cases is the result of hardening by precipitation of a supersaturated alloying element, and that strain-aging is probably a similar precipitation, accelerated by disruptions of the lattice by previous strain. Pfeil4 has shown that strain-aging does not occur in iron from which all of the carbon has been removed, but that only a very small carbon content, around 0.003 pct, is necessary to cause strain-aging. In accord with this observation is recent work by Dijkstra5 in this laboratory showing that the solubility limit of carbon in iron is extremely low, less than 0.001 pct at 400°C. Edwards, Phillips and Jones2 have shown that the strain-aging effect is also removed by the addition of small quantities of elements such as Mo, Mn, Ti, and the like, which readily form carbides. Their results demonstrate the

Jan 1, 1950

By Walter H. Bruckner, George B. Clark

SINCE the end of World War II interest has been increasing in the use of shaped charges in the mining industry and in other industries using explosives for blasting purposes. Shaped charges employ the principle known as the "Munroe effect," which was discovered by Charles E. Munroe more than 50 years ago (in 1888). Details of their design have been explained e1sewhere.l,2,3 Fig I shows the essential features of design of two types of shaped charges (with conical and hemispherical cavities) and a schematic sketch of their action upon detonation. The following discussion deals with the behavior of the metal in the cavity liners when they are subjected to intense pressures exerted when the explosive charge is detonated. Among the conclusions reached in research on shaped explosive charges, the following have been established concerning cavity liners: 1,2 I. The optimum wall thickness of a conical cavity liner is dependent upon the apex angle of the cone as well as on the base diameter of the charge. Acute apex angles require thinner walls for optimum performance and more obtuse angles require thicker walls for the same base diameter. 2. Cones were more effective in forming a penetrating jet when the walls were tapered; i.e., the thickness of the wall of the cone increased from the apex down. 3. The physical and mechanical proper- ties of metals have a marked effect upon their performance as cavity-liner material. Boiling point, ductility, malleability, tensile strength, and hardness are among the properties that influence the effectiveness of a metal used as a cavity liner. Lead, for example, makes a wide, flat crater in steel plates. Aluminum makes a deeper crater than lead, and an aluminum alloy having a high tensile strength makes a deeper hole, but slightly smaller in diameter. Cast iron makes a deep, narrow hole. These findings, together with the following analysis under Metallographic Survey of Slug, offer solutions to many of the problems involved in solving the mechanism of the formation of Munroe jets. It has been fairly well established that cavity liners collapse in a manner similar to that indicated in Fig 2. Conical liners are known to collapse upon themselves while hemispherical liners are believed to turn inside out in the process of jet formation. The first has been definitely proved by recovery of collapsed portions of cones, while liners from partly detonated charges show that hemispheres may turn inside out. Fig 3 shows a sketch of a recovered slug from a 6-in. shaped charge using a 45° cone made of cast iron. (This size of charge drilled holes up to 3 ft in depth in solid granodiorite.)

Jan 1, 1947

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By Charles A. Ashburner

A very limited development has been made of the coal-fields of this Territory. This is to be accounted for by the fact that a number of the coal-fields lack railroad transportation, by the distance of other fields from the consumers (due to restricted settlements), and finally by the poorer quality of a number of coals which have been mined as compared to others which can be economically imported into the Territory. The consumption of coal in Utah during 1886, outside of that used by the railway companies, was: Tons. Utah coal,..........110,000 Wyoming coal,. .....19,000 Colorado coal,........* 4,945 Total,........... 133,945 It is estimated that there are 1100 miles of railroads in the Territory which use coal for fuel. The consumption of these roads for the year is estimated at 100,000 tons, making an aggregate consumption in the Territory of 223,945 tons. The consumption of coal in Salt Lake City duriug the year was as follows: Tone. From Grass Creek mines,.......21,000 " Pleasant Valley Company's mines,.. 12,700 " Utah Central Company's mines,.9,000 " Bock Spring mines,.6,500 " Almy mines .. ., .. .. . 6,000 " Miscellaneous sources,..5,800 Total ,.........60,000

Jan 1, 1888

By Oliver B. Hopkins

Peruvian production for the year 1935 amounted to 17,064,879 bbl., a record amount for any year, bringing the cumulative production of the country up to 188 million barrels. The 1935 figure is an increase of 785,769 bbl. over the 1934 total. The property of the International Petroleum Co. contributed 636,812 bbl. of this increase, and the Lobitos property 158,625 barrels. Exploration work in the country was again active, with attention focused on three areas, the Huallaga River, Lake Titicaca and the Coastal Zone of the Province of Tumbes. It is reported that in the Huallaga River area the Selden Breck Construction Co. has completed geological and engineering studies on its Pachitea River concessions and has ordered a drilling rig. In the Lake Titicaca region further studies in the vicinity of Pusi were made by Government geologists. During the period from 1906 to 1915, the Pirin anticline in this area produced 285,936 bbl. of low-grade crude. The Government holds 120,000 hectares of reserved lands in this area. In the Coastal Zone of the Province of Tumbes explorations by the Government were continued on the National Reserve, and a test location has been selected in the Quebrada Zapotal about 10 miles from the Port of Zorritos. An order has been placed in the United States for drilling equipment. LaBrea-Parinas Estate.—Production on the LeBrea-Parinas Estate reached an all-time high in 1935 of 14,756,914 bbl., an increase of 636,812 bbl. over the 1934 record. The total production from 1890 to 1935 was 148,541,523 bbl. During 1935 a total of 63,021 ft. was drilled in new wells and 5449 ft. in deepening existing wells; 23 wells were deepened and 29 new wells were completed, of which 27 were producers and 2 were dry holes. At the end of the year 2873 wells had been drilled on the Estate, of which 1838 were still productive. The remaining 1035 wells represent abandoned producers or dry holes. Practically all the drilling on the property has been done with cable tools, but during 1934 three strings of rotary tools were introduced. Experience with these outfits has shown that rotary equipment can

Jan 1, 1936

By Oliver B. Hopkins

Peruvian production for the year 1935 amounted to 17,064,879 bbl., a record amount for any year, bringing the cumulative production of the country up to 188 million barrels. The 1935 figure is an increase of 785,769 bbl. over the 1934 total. The property of the International Petroleum Co. contributed 636,812 bbl. of this increase, and the Lobitos property 158,625 barrels. Exploration work in the country was again active, with attention focused on three areas, the Huallaga River, Lake Titicaca and the Coastal Zone of the Province of Tumbes. It is reported that in the Huallaga River area the Selden Breck Construction Co. has completed geological and engineering studies on its Pachitea River concessions and has ordered a drilling rig. In the Lake Titicaca region further studies in the vicinity of Pusi were made by Government geologists. During the period from 1906 to 1915, the Pirin anticline in this area produced 285,936 bbl. of low-grade crude. The Government holds 120,000 hectares of reserved lands in this area. In the Coastal Zone of the Province of Tumbes explorations by the Government were continued on the National Reserve, and a test location has been selected in the Quebrada Zapotal about 10 miles from the Port of Zorritos. An order has been placed in the United States for drilling equipment. LaBrea-Parinas Estate.—Production on the LeBrea-Parinas Estate reached an all-time high in 1935 of 14,756,914 bbl., an increase of 636,812 bbl. over the 1934 record. The total production from 1890 to 1935 was 148,541,523 bbl. During 1935 a total of 63,021 ft. was drilled in new wells and 5449 ft. in deepening existing wells; 23 wells were deepened and 29 new wells were completed, of which 27 were producers and 2 were dry holes. At the end of the year 2873 wells had been drilled on the Estate, of which 1838 were still productive. The remaining 1035 wells represent abandoned producers or dry holes. Practically all the drilling on the property has been done with cable tools, but during 1934 three strings of rotary tools were introduced. Experience with these outfits has shown that rotary equipment can

Jan 1, 1936

Masjid-i-Su1aiman.—There have been no new developments in the Masjid-i-Sulaiman oil fields during the year 1938. In spite of the age of this field, the fall in dome pressure shows no appreciable variation from the low rate of about 0.3 lb. per sq. in. per million tons net production. Drilling has been limited to deepening old wells and to new wells required for maintenance of production and general reservoir control. The rate of offtake has been reduced over the past few years, partly because of depletion of the oil column, and it is expected that future offtake from the Masjid-i-Sulaiman field will be stabilized for some years at around the present figure of 3,000,000 tons per annum. Haft Ke1.—An exploratory well to test deeper formations in the Haft Kel field has proved the existence of productive conditions in the Eocene, which underlies the Asmari limestone (the main producing horizon). Drilling to the northwest in the white-oil springs area has revealed the presence of a separate structure with productive potentialities. One well with a satisfactory production rate has been completed. Offtake from the Haft Kel field has steadily increased since it first came on to production in 1929. Naft-i-Shah.—Production from this field has continued to supply market requirements in northwest Iran. The policy of returning surplus products to the reservoir, which was adopted at the beginning of 1936, has been continued.

Jan 1, 1939