Search Documents

By Lester C. Uren

It is realized that the depth of fluid maintained in a pumping well is sometimes influenced by other considerations than the quantity of fluid that will enter the well: the prevention of sand incursion, prevention of waste of natural gas, and the maintenance of a suitable submergence for the pump, for example. These latter factors have an important influence on the productivity of the well, so that otherwise unwarranted fluid levels must sometimes be maintained to offset them; but where the handling of unconsolidated sands is not a problem of consequence and where water has been properly excluded, the principles developed here and the practices recommended should apply. The principal objective of the producer should be to produce the maximum quantity of oil in the shortest possible time. Any method or equipment that will increase the rate of production during the early years of the life of the well, when gas pressure is high, will greatly augment the ultimate production. The maintenance of a proper fluid level in the well at all times will go far toward accomplishing this desired result. For a given set of conditions surrounding the flow of oil into a particular well, in which the viscosity of the oil, the porosity and grain size of the sand, and the diameter of the well appear as constants, two variables determine the quantity of oil that will flow from the sand into the well. These are: the effective pressure behind or within the oil in the reservoir sand, and the fluid level maintained within the well. The former is the expulsive force that causes movement of oil from the sand into the well, while the latter determines the magnitude of a resisting force opposing such movement. The first of these factors is largely beyond the control of the oil producer, but it is in his interest to reduce the opposing force to the lowest economic limit.

Jan 1, 1925

By Robert H. Richards

It has long been known to boiler makers and to the users of cylindrical pipes of many kinds that when a tube is exposed to internal fluid pressure the resolution of forces is such that the material of the walls of the tube is exposed to twice the stress in the direction tending to produce longitudinal rupture, as it is in the direction to produce circumferential fracture. By longitudinal fracture is meant the fracture by a rent parallel to the axis; by circumferential fracture is meant fracture by rents running round the cylinder. In consequence of this the makers of boilers always lay the fibre of their metal in direction round the boiler, and the same is true with the makers of gun-barrels. I have never seen any good and simple illustration of this law until I met with it in blowing glass. If a thin bubble of glass be blown out in a spherical form and then exploded it will be found that the particles tumble into totally irregular shapes, showing no special direction in the molecular structure of the material. If now a bubble of glass be blown out and so manipulated that it will take a cylindrical form (see accompanying illustration), and then be exploded, it will drop into ribbon-shaped pieces from end to end, and the only parts that will be found to differ from this form will be the two hemispherical ends which will remain whole, having a fringe of ribbons representing the line of their fracture from the cylinder. The main point of difference between this experiment and the

Jan 1, 1883

By W. C. Browning

The influence of the hydroxyl factor is more damaging to formations penetrated and causes greater consumption of drilling mud additives than previously realized. This hydroxyl effect on clays is essentially independent of the cations present in the drilling fluid and thus differs from the base exchange reactions that have preoccupied mud chemistry with sodium and calcium bentonite concepts for nearly two decades. The new organic polyelectrolyte-con-ditioned muds haw made it possible to use materials other than sodium hydroxide to maintain the alkalinity of such muds. The properties of silicates, as indicated by their dissociation characteristics and buffering action, are such that they can control he pH and alkalinity of drilling muds at the desired level and, at the same time, minimize undesirable hydroxyl effects associated with sodium hydroxide. This use of silicate compounds is different and distinct from prior applications of silicates as deflocculants or shale preservers. Laboratory and field data presented in this report show that silicate compositions can be utilized to adjust the alkalinity of drilling muds and, at the same time, minimize hydmxyl-promoted clay cleavage. INTRODUCTION Studies for improving the efficiency of rotary drilling techniques must consider the chemistry of drilling fluids and of the formations being penetrated. The chemical aspects of drilling must be studied in conjunction with and in relation to the mechanical factors if, for example, penetration rates are to be optimized. Drilling fluid technology has been largely influenced by chemical reactions of the montmorillonite (bentonite) clay minerals. Most of the literature of mud chemistry concerns the properties of bentonite. Clays of the kaolin or illite type, which are nonswelling, are not generally regarded as sources of drilling mud problems. If these nonswelling shale clays are considered, they are commonly regarded as inert solids. Particularly noteworthy is the fact that the relation of surface and colloid chemistry to massive shale bodies has received only scant attention from drilling technologists. Clay studies reported in the drilling mud literature have dealt, for the most part, with the properties of clays in a finely divided state, and often in very dilute suspensions. Yet frequently during drilling, shale problems not related to the rheology of clay suspensions develop in massive non-bentonitic shale sections of zero or near zero permeability. This paper is concerned with surface chemical reactions that can influence the behavior of these non-bentonite clay masses in such a manner as to adversely affect drilling operations. Browning and Perricone1,2 have pointed out that some of the most troublesome shales to drill, such as the Atoka, contain no montmorillonites. They also pointed out that mud problems can frequently be mitigated by reduction of clay cleavage achieved by using drilling fluids with a minimum of available hydroxyl ions. If pronounced clay cleavage occurs during drilling, the borehole may soften, increasing the possibility of sloughing. In addition, the resulting increased incorporation of high-surface-area clay solids into the mud system can reduce penetration rates and necessitate greater chemical treatment. This increase of shale, of colloidal or near-colloidal dimensions, into the drilling mud is due to clay aggregate cleavage and not to base exchange or swelling reactions, such as occur with bentonites. Searle and Grimshaw3 point out the difference between cleavage or slaking reactions of nonswelling clays (such as illite and kaolinite) and the swelling of bentonite. They further state that the speed of slaking is increased in alkaline water. Eitel1 cites Salmang and Becker, who recognized that clay surface reactions impart plasticity and workability to clay masses. Their results clearly show that all liquids which contain hydroxyl groups in their molecules favor the workability of clays. The ancient technique of aging clays in the moist condition to increase their "workability" is evidence that these clay cleavage phenomena are of considerable importance. The same hydration cleavage that occurs during the aging of nonswelling clays for ceramic use also acts to break up cuttings and soften the borehole during drilling operations. The mechanism of cleavage of the crystalline aggregates of illitic, kaolinitic and other nonswelling clays; and the chemical means of controlling this cleavage are therefore of considerable significance to the drilling mud chemistry. Inasmuch as there is little reference in the drilling mud literature to the cleavage reactions of nonswelling clays, the structure of these clays and certain properties that relate to the mechanism of clay cleavage will be reviewed briefly. STRUCTURE OF NONSWELLING CLAYS Clays such as kaolinite, illite and montmorillonite are compmed of alternate layers of (1) silicon-oxygen tetra-

Jan 1, 1965

By Ben. B. Cox

The principal events during the year consisted in the exploitation of the Kirkuk field, the regular operation of the four-million-ton pipe line to the Mediterranean, and the discovery of low-gravity oil on three other structures in the West Tigris (Shergat) area. The Iraq Petroleum Co., Ltd. continued the systematic exploitation and exploration of its Kirkuk field, maintaining a carefully unitized operation. Bottom-hole pressure differentials and low gas-oil ratios were maintained. All crude was produced by flowing The cleaning up following the construction of the Mediterranean pipe line, which began deliveries in August, 1934, was completed during the first quarter of 1935. The line easily maintained its rated capacity for the remainder of the year. The Mosul Oilfields, Ltd., through its operating subsidiary, the B.O.D., Ltd., expanded its exploratory organization from 9 to 16 drilling rigs and discovercd 20" A.P.I. crude on the Sadid, Hibbarah and Qasab anticlines. Whether these discoveries will be commercial pools remains to be proved. The Qaiyarah-Najmah-Jawan field, which was discovered by the I.P.C. in 1928, was extended arid production was found in the Eo-Cretaceous as well as the "Main Limestone" (Eocene, Oligocene and Lower Miocene). Gas caps were found under each of the crests of the West Tigris structures. Negotiations are in progress between the Mosul Oilfields, Ltd. and the Iraq Government for the extension of the Anatolian Railway from the Turkish border to Mosul, with a view to tanking the heavy West Tigris crude to the Mediterranean. The subsidiary of the Anglo-Iranian Oil Co., Ltd.', the Khanaqin Oil Co., Ltd., continued to operate its Naft Khaneh field near the Iranian (Persian) border to supply the local Iraq market through the Rafidain Oil Co., Ltd. Somewhat more than 28 million barrels of crude was produced in Iraq during 1935. Crude delivcred to the pipe line for export during the years 1934 and 1935 was: Year BaRrels 1934................................................. 7,096,669 1935................................................. 27,014,904 Total as at Dec. 31, 193.5.............................. 34,111,573 ° Converted at an avcrage of 7.0 bbl. per ton.

Jan 1, 1936

The principal events during the year consisted in the exploitation of the Kirkuk field, the regular operation of the four-million-ton pipe line to the Mediterranean, and the discovery of low-gravity oil on three other structures in the West Tigris (Shergat) area. The Iraq Petroleum Co., Ltd. continued the systematic exploitation and exploration of its Kirkuk field, maintaining a carefully unitized operation. Bottom-hole pressure differentials and low gas-oil ratios were maintained. All crude was produced by flowing The cleaning up following the construction of the Mediterranean pipe line, which began deliveries in August, 1934, was completed during the first quarter of 1935. The line easily maintained its rated capacity for the remainder of the year. The Mosul Oilfields, Ltd., through its operating subsidiary, the B.O.D., Ltd., expanded its exploratory organization from 9 to 16 drilling rigs and discovercd 20" A.P.I. crude on the Sadid, Hibbarah and Qasab anticlines. Whether these discoveries will be commercial pools remains to be proved. The Qaiyarah-Najmah-Jawan field, which was discovered by the I.P.C. in 1928, was extended arid production was found in the Eo-Cretaceous as well as the "Main Limestone" (Eocene, Oligocene and Lower Miocene). Gas caps were found under each of the crests of the West Tigris structures. Negotiations are in progress between the Mosul Oilfields, Ltd. and the Iraq Government for the extension of the Anatolian Railway from the Turkish border to Mosul, with a view to tanking the heavy West Tigris crude to the Mediterranean. The subsidiary of the Anglo-Iranian Oil Co., Ltd.', the Khanaqin Oil Co., Ltd., continued to operate its Naft Khaneh field near the Iranian (Persian) border to supply the local Iraq market through the Rafidain Oil Co., Ltd. Somewhat more than 28 million barrels of crude was produced in Iraq during 1935. Crude delivcred to the pipe line for export during the years 1934 and 1935 was: Year BaRrels 1934................................................. 7,096,669 1935................................................. 27,014,904 Total as at Dec. 31, 193.5.............................. 34,111,573 ° Converted at an avcrage of 7.0 bbl. per ton.

Jan 1, 1936

By William B. Harris, Leonard Greenburg, Gustav Werner

Haulage in tunneling operations generally has been done with electric locomotives. As a rule, on short hauls the source of electricity is a storage battery mounted on the locomotive, which, of course, must be removed and recharged periodically. Where the distance from the recharging point to the tunnel face is very long, and where loads are heavy, trolley-driven locomotives are used. Diesel engines have been used in mining and tunneling operations in Europe for a number of years. The recent reports of studies in Belgium1 and by the Bureau of Mines in this country2-4 have indicated the potentialities of this form of power for haulage, mucking, bulldozing and many other underground operations. The hazards attending the use of Diesel engines in more or less closed spaces have long been known. The exhaust constituents that may create a harmful or objectionable environment are carbon monoxide, oxides of nitrogen and sulphur, carbon dioxide, aldehydes and smoke. Lack of precise information regarding the concentration of these gases and the ventilation requirements to reduce them to safe levels has to some extent suppressed their general acceptance in tunneling and mining work. Not until the work of the Bureau of Mines referred to above, and certain experience gained in the construction of the Delaware Aqueduct, ‡ has there been available the requisite information regarding the conditions under which their use may be permitted. This paper concerns itself with the successful operation of Diesel engines underground in the construction of certain parts of the Delaware Aqueduct, and describes the conditions under which Diesel engines have been found to operate with a minimum production of noxious gases. The test data reported were obtained during the operation of Diesel engines over a period of two years.* Studies by the New York State Department or Labor Exhaustive tests were made by the Division of Industrial Hygiene, of the composition of the exhaust gases given off by a Diesel engine mounted on a test block. These tests showed that certain' quantities of the gases are discharged from the exhaust. On the basis of these figures, preliminary requirements of design and control

Jan 1, 1943

By Gustav Werner, Leonard Greenburg, William B. Harris

Haulage in tunneling operations generally has been done with electric locomotives. As a rule, on short hauls the source of electricity is a storage battery mounted on the locomotive, which, of course, must be removed and recharged periodically. Where the distance from the recharging point to the tunnel face is very long, and where loads are heavy, trolley-driven locomotives are used. Diesel engines have been used in mining and tunneling operations in Europe for a number of years. The recent reports of studies in Belgium1 and by the Bureau of Mines in this country2-4 have indicated the potentialities of this form of power for haulage, mucking, bulldozing and many other underground operations. The hazards attending the use of Diesel engines in more or less closed spaces have long been known. The exhaust constituents that may create a harmful or objectionable environment are carbon monoxide, oxides of nitrogen and sulphur, carbon dioxide, aldehydes and smoke. Lack of precise information regarding the concentration of these gases and the ventilation requirements to reduce them to safe levels has to some extent suppressed their general acceptance in tunneling and mining work. Not until the work of the Bureau of Mines referred to above, and certain experience gained in the construction of the Delaware Aqueduct, ‡ has there been available the requisite information regarding the conditions under which their use may be permitted. This paper concerns itself with the successful operation of Diesel engines underground in the construction of certain parts of the Delaware Aqueduct, and describes the conditions under which Diesel engines have been found to operate with a minimum production of noxious gases. The test data reported were obtained during the operation of Diesel engines over a period of two years.* Studies by the New York State Department or Labor Exhaustive tests were made by the Division of Industrial Hygiene, of the composition of the exhaust gases given off by a Diesel engine mounted on a test block. These tests showed that certain' quantities of the gases are discharged from the exhaust. On the basis of these figures, preliminary requirements of design and control

Jan 1, 1943

By B. H. G. Brady, C. M. St. John

Computational schemes for analysis of rock mass response to excavation, loading and other imposed changes, are employed pervasively in rock mechanics practice. Applications range in complexity from determination of stress and displacement distributions around openings, to prediction of the thermo-hydromechanical behaviour of a saturated fissured mass. While this may be taken as apparent sophistication in rock mechanics design activity, the indiscriminate use of computer methods may sometimes conceal inferior and inadequate engineering procedures. These inadequacies may not always be recognized, due to the general uncertainties which are inherent in rock mechanics investigations. This paper seeks to identify some common deficiencies in rock mechanics applications of computational schemes, and to propose ways of eliminating them. It also indicates some specific developments and applications of computational procedures, which are required to address persistent design problems in geomechanics practice.

Jan 1, 1982

By George W. Lower, William A. Hockings, Donald A. Kaczynski

The rate of dissolution of polycrystalline metallic copper in aqueous cupric ammonium nitrate solutions in the non-film-forming region was investigated by the rotating disc method. The investigation was performed in solution concentration ranges applicable to hydrometallurgical processes. This investigation was an extension of a study on the cupric ammonium carbonate system previously reported by Smith, Lower and Hockings, in which the following kinetic model was proposed: (1) Diffusion of cupric ammine ions to the copper surface; (2) Forward reaction - first order reaction of cupric ammine ions with metallic copper; (3) Reverse reaction - disproportionation of cuprous ammine ions to metallic copper and cupric ammine ions ; and (4) Diffusion of cuprous ammine ions from the copper surface. The nitrate system was selected for this study because it simplified the determination of the ionic composition of the solutions. The variables studied were stirring speed and cupric, ammonia, and nitrate concentrations. The dissolution rate increased linearly with at low values of but exhibited increasingly negative deviations from linearity at higher values of m. The rate also increased with increasing cupric concentration but decreased with increasing ammonia and nitrate concentration. Good agreement was obtained between the experimental rate data and the proposed model. Further verification of the model was indicated by the close agreement of the diffusion coefficient calculated from the data and comparable literature values.

Jan 1, 1974

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

In situ extraction for copper, gold and uranium, generally involves several common alternative processes and techniques. These include dump leaching, heap leaching, leaching of fractured ore in-place or bore hole mining and unit operations such as cementation, solvent extraction, ion-exchange or carbon-in-pulp. Since the metallurgical effectiveness and economics of such processes and unit operations are well established, it would be possible to select the optimum alternative for extracting either copper, gold or uranium from their ores using in situ extraction technology. In this paper, efforts have been made to provide metallurgical evaluation as well as capital and operating costs for the various processes and unit operations. Attempts have also been made to utilize the above costs in preparing feasibility studies for in situ extraction of these metals.

Jan 1, 1976

By Herbert H. Mellus

TODAY the tractor-drawn carryall scraper has a very important role in the Open Pit div. of Inspiration Consolidated Copper Co. Carryalls have already moved over 3 million tons of material at costs comparable to or lower than for conventional truck and shovel operation, and a major program of scraper stripping and ore production schedules has developed from early isolated scraper applications.

Jan 10, 1953

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

By David A. Thomas, David N. French

The lrnrdness of WC crystals has been measured with the Knoop indenter at loads of 100 and 500 g on the (0001) and (1070) planes. The hardness as tneasitred on the basal plane is 2400 kg per sq mm and shows little anisotropy. The hardness on the prism plane, however, shows a marked orientation dependence, with a low value of 1000 kg -per sq mm when the long axis of the Knoop indenter is oriented parallel to the c axis and a high value of 2400 kg per sq mm when the indenter is perpendicular to the c axis. Slip lines (Ire observed surrounding the microhardness indentations and they show slip on (1010) planes, probably in [0001] and (1120) directions. This slip behavior can be explained by the crystal structure of TVC, which is simple hexagonal with a c/a ralio of 0.976. The hardness anisotropy call be explained by [0001]{1010} and (1130) {10l0] slii) and the resolved shear-stress analysis of Daniels and Dunn. HARDNESS anisotropy is a well-known phenomenon and has been reported for many metals, with both cubic and hexagonal structure.1-6 For hexagonal tungsten carbide, WC, a wide range of hardness values is reported in the literature. For example, Schwarzkopf and Kieffer7 give a hardness of 2400 kg per sq mm and report a value of 2500 kg per sq mm by Hinnüber. Foster and coworkerss give the average Knoop microhardness as 1307 kg per sq mm with a maximum value of 2105 kg per sq mm. Although these values and the structure of WC suggest the likelihood of hardness anisotropy, no such measurements have been made. We first detected a large apparent hardness anisotropy in WC crystals about 75 p large, in over-sintered cemented tungsten carbide. Prominent slip lines also occurred around many indentations. This report presents further observations and interpretations of hardness anisotropy and slip in WC crystals obtained from Kennametal, Inc. Both Knoop and diamond pyramid indenters were used on a Wilson microhardness tester with loads of 100 and 500 g. EXPERIMENTAL RESULTS The carbide crystals tended to be triangular plates parallel to the (0001) basal plane of the hexagonal structure. The side faces were parallel to the ( 1010) prism planes. Specimens were mounted approximately parallel to these two types of faces and metallographically polished. Laue back-reflection X-ray patterns were used to orient the specimens, which werethen ground to within ±1 deg of the (0001) and (1010) planes. The Knoop hardness values measured on the basal plane are plotted in Fig. 1. There is only a small anisotropy, with a hardness range of 2240 to 2510 kg per sq mm. The additional points at angles from 52.5 to 67.5 deg confirm the sharp minimum hardness at 60-deg intervals, consistent with the sixfold hexagonal symmetry. The average hardness of all values obtained on the basal plane is 2400 kg per sq mm. While the basal plane shows only slight anisotropy, the (1010) plane exhibits marked hardness anisotropy, from 1000 to 2400 kg per sq mm. Fig. 2 shows the hardness as a function of the angle between the long axis of the indenter and the hexagonal c axis, the [0001] direction. The minimum and maximum occur when the indenter is oriented parallel and perpendicular to the [0001] direction, respectively. The anisotropy of the prism plane is contrary to that reported for hexagonal zinc and hard- However, the basal-plane anisotropy is similar to these two metals.1'2 To check the accuracy and reproducibility of the measurements, a series of fifteen impressions was made at 100-g load in the same orientation in the same area of the specimen surface. The average for all was 2040 kg per sq mm, with a range of 1950 to 2130 kg per sq mm, giving an accuracy of about ± 5 pct. Thus the slight anisotropy on the basal plane is almost within experimental error. Fig. 3 shows slip lines around the Knoop indentations on the basal plane. The slip traces are in directions of the type (1130). The presence of slip steps on the basal plane indicates that the slip direction lies out of the (0001) plane. Because WC has a c/a ratio of 0.976,' the shortest slip vector is [0001], which suggests slip systems of the type [0001] (1010). Fig. 4 shows slip lines around the Knoop intentations on the (1010) plane. These slip lines are inconsistent with [0001] slip but can be

Jan 1, 1965

By B. B. Cox

The Iraq Petroleum Company, Ltd. continued its systematic exploration and exploitation of the Kirkuk field on a unitized basis. Pressures, gas-oil ratios, oil-water level and oil-gas level remained satisfactory. All wells were produced by flowing and more than two-thirds of the crude was stabilized. The only exports from Iraq during 1937 were from the Kirkuk field. Mosul Oilfields, Ltd., through its operating subsidiary, the British Oil Development Company, Ltd., inaugurated an exploratory program to find lighter oil than the heavy, black, sulphurous reserve proved in the Qaiyarah-Najmah-Jawan-Qasab field. Deeper drilling in this field found a small reserve of 17" to 19" A.P.I. black sulphurous oil in the Pilsner (Upper Cretaceous). Ten structures outside the proved field were tested or were under test at the end of the year. In spite of this intensive program no reserve of lighter oil was discovered. The reserve at Qaiyarah-Najmah-Jawan-Qasab averages 16" A.P.I. with 6+ per cent sulphur from the "continuous limestone" (Lower Miocene, Oligocene, Middle Eocene) and from the Pilsner (Upper Cretaceous). The Khanaqin Oil Company, Ltd., a subsidiary of the Anglo-Iranian Oil Company, Ltd., conducted the normal exploitation of its Naft Khaneh oil field and supplied the local Iraq market requirements. Slightly more than 31,600,000 bbl. of crude was produced in Iraq during 1937. The following table gives the total crude produced by the I.P.C. for export during the last four years. Year 42-gallon BarreL Increase over Preceding Year 1934 7,096,669 1935 27,014,904 19,918,235 1936 29,521,053 2,506,149 1937 31,171,476 1,650,423 " Converted at an average of 7.6 bbl. per ton. Published by permission of the Near East Development Corporation. Manuscript received at the office of the Institute March 11, 1938. * Geologist, Socony-Vacuum Oil Co., Inc., New York, N. Y.

Jan 1, 1938

By J. H. Wright

Longhole sublevel stopes excavate ore with which the production geologist has only remote contact; therefore, predicting grade and tonnage from such a stope can be a problem. However, the longholes themselves yield data that can be used to improve those predictions. Here, a radial distribution method of weighting sample data is discussed, which is useful in forecasting grade and tonnage from certain longhole sublevel stopes.

Jan 1, 1985

By J. Price Wetherill

THE coal-seams that are worked vary from 32 to 100 feet in thickness, and occur at all angles of inclination, but are never flat for any great extent. They contain coal, slate, and an unsolidified coal, called dirt by the miners, in various proportions, a uniform seam of coal alone being rare. The upper walls are composed of conglomerate, sandstone, or slate; the first two hard and solid in texture, and withstanding the action of the atmosphere and moisture sufficiently well to offer but little trouble to the mining operations ; while the latter crumbles rapidly, owing, in part, to the decomposition of iron pyrites which it contains in large quantities, and in part to its own friable character, and requires constant care to avoid accidents to the men working below it, and to prevent its mixing with the coal mined. The floors are composed of slate. As in all mining operations, the. general system pursued is to reach with a permanent outlet such a point in the seam as will

Jan 1, 1877

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in. a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a. previous paper.' The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques. The general geo1ogy of the Coeur d'Alene district, including a detailed description of the rock types encountered, has been comprehensively treated by Ransome and Calkins' in their classic paper, and only local background description, therefore, is felt to be appropriate here. The Hercules deposit transects a portion of the trough of a broad south-trending synclinorium which has been greatly complicated by faulting. More locally, it lies within a block of ground bounded on the east; by the O'Neil Gulch fault, a steep north-south overthrust of considerable magnitude, and on the west by a monzonite stock, the outcrop of which is 1/2 mile or more wide and 5 miles long. The country rock is composed of thin to medium-bedded argillites and argillaceous quartz-ites of the Prichard and Burke formations, the oldest members of the Pre-cambrian Belt Series of sediments in the area, believed to be of Algonkian age. The contact between them is a conformable gradation. The argillite is colored gray to tannish-gray and is fine-grained, compact, and generally massive in structure. Under the microscope the unaltered argillite is seen to be composed principally of anhedral quartz and a few feldspar grains which were at one time presumably partly rounded sand grains, but as a result of recrystallization and cementation by silica, the interstices are now almost obliterated and quartz grains show crenulate boundaries. The sizes of these crystals vary from 0.5 mm down to 0.1 mm in greatest dimension. In all specimens sericite comprises 10 to 20 pct of the rock and is present abundantly between most of the grains as flakes or shreds which vary considerably in size. Sometimes they form a fine felt-like mat or aggregate, and sometimes flakes are seen which appear to be good muscovite. In some specimens, separated rhombic-shaped carbonate grains are abundant, and in some instances these have been changed to sericite. Mining operations to date have explored the Hercules vein to a maximum vertical depth of 3600 ft below its outcrop, and along a maximum strike-length of 3600 ft on certain of the lower mine levels. The main orebody is irregular in outline, extending over a variable strike-length of 400 to 1500 ft; and it is intersected by a strong transverse fault that has been traced from the surface to the bottom level. This has been named the Hercules fault, and apart from the vein itself, it is the most prominent structural feature in the mine. There is good evidence that it existed prior to the introduction of ore solutions and may have influenced ore deposition, but it was also the locus of important post-ore displacement and shows a progressive right-handed horizontal component reaching 200 ft on the deeper levels. Its vertical component is not definitely known but may be considerably greater. The fault strikes 20° N to 50° E and dips westerly at angles of 70" to 45", flattening in dip where it crosses the original orebody from east to west between 1000 and 1600 ft below the surface. At about 3000 ft in depth the Hercules fault is joined by a vertical fault of similar strike, and the major post-ore dis-placement below their junction is taken up along this vertical branch of the structure, now called the Mercury fault. Recent work has been concentrated in this vicinity. Another structural feature of special geologic interest, though of little economic importance, is the occurrence of a porphyritic dike in this area. This lies a short distance above the Hercules fault, essentially parallel to it, and is 5 to 15 ft in thickness. It appears at first glance to cut the mineralization, suggesting push-apart relationship, but small stringers of the vein minerals have been observed to penetrate the dike for a matter of inches at several points. The dike is thought to be related to the monzonite intrusion. A vertical longitudinal projection of the mine is shown in Fig. 1, which illustrates most of the features discussed above. The Hercules vein was deposited along the course of a strong, persistent shear zone that now appears as a braided network of gouge seams running through more or less crushed and shattered country rock. It strikes 70° N to 80° W and dips southerly at an average of 75". Barren parts of the structure vary in width from less than 1 ft to more than 15 ft. The width of mineralized segments may be double that. Although the evidence is not conclusive, pre-mineral, normal movement along the zone may be 1000 or 1500 ft. The horizontal component is unknown. Post-ore movement appears to have been

Jan 1, 1954

By S. A. Ford

A SHORT and accurate method for the estimation of manganese in iron and steel is of great advantage to Bessemer works, and I think it may be of interest to some of the members of the Institute to give in detail the process in use in the laboratory of the Edgar Thomson steel works. The process is based on the reaction first described by Beilstein and Jawein.* The steel, spiegel, or iron is dissolved in strong nitric acid, sp. gr. 1.4. Evaporation to dryness is not necessary, unless the amount of silicon is large, as in the case of certain pig irons. Then, as a clogging of the filter in the subsequent filtra¬tion is apt to follow, dissolve first in a dish in hydrochloric acid, quickly evaporate to dryness, redissolve in the strong nitric acid, boil, and while boiling throw in crystals of chlorate of potash from time to time. Violent action ensues, yellow fumes are given off, and binoxide of manganese is precipitated, since it is insoluble in strong * Berichte der deutschen chemisehen Gesellschaft, vol. xii, page 1528.

Jan 1, 1881

By J. C. McCarthy, J. B. Stone

AT Fresnillo a series of veins that has yielded very large quantities of silver and other metals has been developed over a length of 6500 ft. and to a depth of over 3000 ft. In the course of this work striking changes in the mineralogy and metal content of the principal veins have been disclosed and are well illustrated by assay data and ore reserve calculations. This paper describes those changes and suggests their bearing on theories of ore deposition. LOCATION The Fresnillo mines and the adjacent city of Fresnillo are in the central part of the state of Zacatecas, 35 miles northwest of the capitol city of Zacatecas, once a great silver-mining center whose total production is said to place it fourth in the world. Another famous old silver district, Sombrerete, lies northwest of Fresnillo. Fresnillo is connected by a 5-mile branch with Fresnillo station on the Mexican National Railways line from Juarez to Mexico City. Lying near the southwestern edge of the central plateau of Mexico, Fresnillo ís surrounded by a semi-arid rolling plain from which rise widely scattered low hills. One of these is Proaño hill, an inconspicuous elevation rising barely 300 ft. above the plain, but in and around Proano hill are the Fresnillo mines, and it is marked now by a great gash cut by glory-hole mining. HISTORY According to an account written in 1834 by Francisco García, then Governor of the state of Zacatecas, Fresnillo was discovered in 1554, and a presidio was established there in 1568 to protect travelers on the road between Zacatecas and Sombrerete. Little is known of the earliest mining at Fresnillo, which seemingly began soon after its discovery, but by piecing together various accounts, it appears that mines there were working in 1717 and were notably active ín 1751 under an administrator named Murguía, who left detailed notes describing them. In 1757, however, the mines became inactive because of difficulties with creditors and no doubt also because of increasing water troubles, and they remained abandoned until 1830. In 1830 the mines at Fresníllo became the property of the State of Zacatecas because the interest of Governor García had been aroused by the long disregarded notes of Murguía. Under García's energetic leadership the mines were reopened, and silver production began in 1832 ín spite of serious difficulties, including abnormal rains and an epidemic of cholera. In 1835 English capital was sought to allow installation of steam-driven Cornish pumps at the two principal shafts and to build the great hacienda de beneficio (the present Proaño hacienda). The company formed in 11835 (Cia. Zacatecano Mexicana) operated successfully until 1872, when its career was brought to an end by the political and economic disturbances

Jan 1, 1942

By R. Maddin, C. H. Mathewson, W. R. Hibbard

According to conventional crystal mechanics, a face-centered cubic single crystal slips on the system {111} <110> which receives the highest shear stress in terms of the stated orientation of the stress axis of the crystal.l However, in brass, the slip process is never as simple as this conventional analysis indicates. There is always a second cooperating plane which contains the same slip direction as the primary plane.2&apos;3 There is still another cooperating slip system commonly called the conjugate system3 previously observed to function with considerable lag only after the rotation due to the action of the first plane had produced a symmetrical condition of equal shear stress on the two systems. In the 1943 Campbell Lecture,4 a slip mechanism was outlined in which the {111) planes moved step-wise in two adjacent <112> directions integrating into the <110> slip direction. "... the slipping process would be visualized as a succession of steps 30" to the right and left of the resultant, microscopically observed, slip direction; a first step setting up the twinned configuration in the single spacing involved and an ensuing slip returning the atoms to the untwinned configuration while completing a fully integrated <110> movement."4 This process is shown diagrammatically in Fig 1 which shows two close packed layers of atoms at a slip site. A movement of the full circles through the "valleys" into the adjacent sites would produce a twin configuration with respect to the open circles. The term, "twin fault," seems most appropriate to define this faulted condition of the lattice. Annealing twins in face-centered cubic metals may arise from preformed nucleii which could be described as twin faults produced by the first movement of this two stage slip process. However, it is clear that this kind of slip does not take place so as to embrace a measurable number of adjacent planes because careful X ray examination has not conclusively shown the existence of ponderable twin lamellae (as in the case of Neumann bands in the body-centered ferrite). In view of the imponderable character of these hypothetical twin faults, the search for evidence of their existence seems restricted to indirect methods. The most obvious experimental technique serving this purpose is the determination by micrographic and X ray methods of the alignment of the composition planes of annealing twins with the former slip planes in axially strained and recrystallized single crystals. In previous attempts of this sort not all of the annealing twins could be traced to slip planes known to be operative in the conventional sense and hence evidence appeared negative or inconclusive. With the discovery of additional slip systems2&apos;3 operating in conjunction with&apos; the major system of highest resolved shear stress in axially strained brass it became apparent that the simple technique outlined above might be re-employed with more gratifying results. If, on annealing single crystals of alpha brass previously strained in tension, twins are found with their composition planes parallel to all three operative slip planes and with no participation of the fourth plane there is good evidence in favor of the existence of twin faults and of the two stage slip process. Experimental Procedure and Resuits Single crystals of alpha brass of the 70-30 composition were grown by solidification from the molten state.

Jan 1, 1950