Search Documents

By Leon McCulloch

WIIen clean iron and metallic zinc dust, protected from the air, arc heated below the melting point of zinc, the iron takes on a coating that has excellent protective value. This coating is a brittle alloy of zinc and iron, and the process is called sherardizing. Although the zinc particlcs are covered with oxide and cannot touch the iron, an extremcly small amount of the zinc vaporizes and the vapor, reaching the iron, alloys with it. Other zinc then vaporizes to replace that which has been removed from the atmosphere. This process continues indefinitely at a decreasing rate, for the coating already formed permits zinc to diffuse through it to combine with the iron beneath. In this way, the coating grows outward from the surface of the iron, as the bark grows from a tree. The method of growth was clcarly seen while sherardizing small cubes of cast iron, at about 450" C., in a srnall glass-stoppcrcd bottle enclosed in a rotating drum. The dust contained about 3 per cent. iron, which prevented caking, and coatings % in. thick were grown in a few hours. After a heavy layer had been formed, the cubes mere again treated for a shorter time. The layer last formed was seen to lie next to the iron, instead of at the outer surface, showing that the growth was from the surface of the iron outward. The coatings split at the edges and corners, leaving the iron exposed there. Flakes of graphite from the iron were lifted upward and embedded in the coatings. The composition of sherardized coatings varies from the outer surface inward, as would be expected from the mode of growth. That is, the iron content increases slowly at first, then more rapidly as the iron is approached. At the surface the least amount of iron possible is 6 per cent., as the experiments described below have shown. A study was made of the effect of iron in zinc dust on the proccss and on the resulting coatings. Glass bulbs, holding the small pieces to be sherardized, together with enough zinc dust to make them two-thirds full, were heated in a small, rotating electrically heated and controlled furnacc. The bulbs had 6-in. (15 cm.) necks, of 96-in. (9.Fj mm.) tubing, plugged

Jan 1, 1923

By George A. Jr. Dornin

A TRULY sound ingot can be made only from steel that is completely deoxidized. Given this condition, there is one further basic requirement-the steel in the ingot must solidify progressively from the bottom to the top. Any method of making the ingot that produces this type of solidification will yield sound products. Since a big-end-down ingot will not satisfy this condition, all sound steel today is produced in big-end-up ingots, the standard tool being the big-end-up mold fitted with some sort of refractory hot top. No one uses hot tops from choice, be cause of the bother and expense involved and because of the low yield resulting from their use-they are used because there has been no alternative where sound steel was required.

Jan 1, 1947

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

There is interest in the use of rhenium metal films as resistive elements in thin-film circcits, and already some zvork has been done using er)aporated rhenium films. It has been found that rheniim films protected from the atmosphere by an evaporated layer of silicon monoxide show excellent electrical stability. Unprotected films, however, are subject to aging- effects, notably the increase in electrical resistivity as a function of time. This phenomenon can be understood as primarily one of oxidation of the thin films. This paper is concerned with the study of the oxidation and crystallization behavior of such unprotected films. It has been found that the oxidation rates are a function of the substrate temperatures used during the deposition of Lhe metal films. The strictures observed in the films are correlated with the film resistivities and some data are presented to establish the existence of the various types of oxides of rhenium. ThERE is some interest in the use of thin films of rhenium metal as resistive elements in monolithic, thin-film integrated circuits. Some work has been done using evaporated films and it has been found that such films, if protected from the atmosphere by an evaporated layer of silicon monoxide, show excellent electrical stability up to temperatures of 500"." Rhenium films unprotected from the atmosphere tend to age and the electrical resistivity of the films increases as a function of time. Rhenium films, of the order of <100A thick, prepared by electron-beam evaporation techniques are found to oxidize very readily when exposed to dry air at room temperature. It would seem, therefore, that this aging phenomenon could be attributed to the oxidation of the metal films. In this investigation, the oxidation and crystallization behavior of thin films of rhenium evaporated onto silicon monoxide substrates were studied as a function of the substrate temperatures used during the evaporation. The films were examined using electron-microscopy and electron-diffraction techniques. EXPERIMENTAL RESULTS Rhenium metal was evaporated onto suitable prepared substrates which were heated to various temperatures. The evaporations were performed in a vacuum of approximately 5 x 1CT5 torr. The evaporation was carried out at a rate of approximately 10A per omin. The final film thickness was approximately lOOA and the resistance ranged from 5000 to 10,000 ohms per square. The substrates used for supporting the metal films were made by evaporating 75A of silicon monoxide onto freshly cleaved mica. The silicon monoxide film was then floated off the mica by immersing the composite in water. The film could then be picked up on a clean nickel grid. Silicon monoxide substrates were chosen because of their similarity to quartz and glass substrates commonly used for making thin-film resistors. Fuschillo, Gimpl, and McMas-ter have also shown that silicon monoxide films have only minor structural changes at temperatures up to 800°C. This fact simplified the interpretation of any changes observed in the electron micrographs or electron-diffraction patterns obtained from the deposited rhenium films. After the evaporations were completed, the substrates were cooled to room temperature, except where noted differently, before the coated substrates were removed from the vacuum system. All aging of the deposited films was done in a desiccator. The evaporated films were examined in an electron microscope equipped with a hot stage that would permit continuous observations of the samples up to temperatures of 1000°C. RESULTS A series of electron micrographs of the rhenium films deposited on the silicon monoxide substrates are shown to Figs. 1 to 3. In all cases, the metal films are approximately 100A thick and the micrographs were taken 1 hr after the deposition was completed. here was no apparent structure in the films deposited on the substrates held at the higher temperatures. The

Jan 1, 1967

By B. W. Adams, R. W. Shilling

9.4-1. Basic principles. DESCRIPTION AND BASIC FUNCTIONS. The concept of inclined skip haulage is not new. The basic idea has been in use at least 400 years. The system is essentially a steeply inclined railway utilizing a hoist to pull the skips to the top or intermediate positions. Inclined skip haulage is often justified where high lifts would require long hauls for other haulage systems. The basic system types are as follows: 1. Single skip, single drum. This system is a single car pulled by a simple hoist system. 2. Balanced skip, single drum. A system utilizing two cars (skips on cables)--one overwound, one underwound-on a single drum. The dead weight of one skip and cable balances the dead weight of the other. As one skip ascends the other descends between two fixed points. 3. Balanced skip, double drum. This system is an elaboration of system No. 2, except the drums may be disengaged from one another to permit the skips to service various loading and dumping points. The preceding are major classifications subject to numerous variations. These variations may be in the skipway, skip design, loading methods, or unloading methods. A few examples follow: 1. The skipway may be standard or special railroad, an overhead monorail or cable, or a ramp for rubber tired vehicles. 2. The skip, per se, may be of varying dumping arrangements (side, bottom, etc.) or could be the box of the vehicle hauling to the skip. 3. Loading may be accomplished directly from the service unit to skip, through an intermediate loading device (e.g., a pocket), or into bins which feed the skip. Loading may be at more than one point. 4. Unloading of the skip can be simple or complex as required. Dumping may be to the haulage unit, to bins and feeders, or to a crusher and conveyor system. Dumping may take place at more than one point.

Jan 1, 1968

By H.E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t&apos;ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon&apos;s3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det&apos;ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. &apos;H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i&apos;vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By H. E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t&apos;ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon&apos;s3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det&apos;ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. &apos;H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i&apos;vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By T. A. Rickard

It has been stated, by Sir James M. Barrie, that "the man of science appears to be the only man who has something to say, just now-and the only man who does not know how to say it". The friendly jibe of the novelist contains enough exaggeration to make it humorous to the followers of Huxley and Spencer; but could any litterateur poke similar fun at the exponents of the avowedly utilitarian branches of science-the men of technology-without suggesting an unpleasant truth? Indeed the engineer does bungle language deplorably. He makes a fetish of efficiency, yet he shows no regard for the effective use of one of his most important tools-the pen; he believes devoutly in accuracy, yet he employs an instrument of precision as carelessly as a small boy handles a gun. This inconsistency may be due to causes such as were indicated by the Academic Senate when it undertook to explain the defective writing of the; students in this university.* The Senate suggested that the student is "constantly subjected by his environment to the unedifying influence of myriad examples of poor English", and that he is also affected by "a certain public prejudice against correctness of expression ". With these statements most of us will agree. Our local newspapers, for instance, tend to spoil the student&apos;s taste for good English; later in life, as an engineer, his daily contact with illiterate men inclines him to careless speech and slovenly writing. As

Jan 1, 1931

By A. J. Lyon, J. B. Johnson, Samuel Daniels

The wrought alloys of aluminum with small amounts of copper and of magnesium have, with the development of the automotive and aircraft industries, sprung into prominence through the medium of duralumin; but the cast alloys remained in the background because their possibilities in the heat-treated condition were either not recognized or not fully investigated. In 1919, the Bureau of Standards published a preliminary survey1 of this field, which pointed out that, in general, the ultimate strength and the percentage of elongation of the alloys of aluminum with and without magnesium could be improved by so simple a treatment as heating at 932&apos; F. (500" C.) for 2 hr., cooling in air, and aging at room temperature for several days. British investigators, too, working with chill-cast material, found that" considerable improvement in the mechanical properties of copper-aluminum alloys may be obtained from suitable heat treatment applied to castings."&apos; Jeffries and Gibson8 made the first contribution to the literature dealing exclusively with the heat treatment of sand-cast aluminum-base alloys, describing the effect of small additions or of combinations of copper, magnesium, and iron on the response to a short heat treatment comprising heating at 932" F. in a nitrate bath for 1 hr., quenching in fish oil, and reheating at 300&apos; F. for for 1 hr. Their results disclosed the facts that the ultimate strength and the percentage of elongation of sound alloys were usually, and quite uniformly, improved by heat treatment; that with the iron content ranging between 0.36 and 0.88 per cent. and the silicon content between 0.24 and 0.60 per cent. the effect of increasing the copper content (Tables 10

Jan 1, 1925

By L. Weaver

THE Tennessee Copper Co.&apos;s mines are in the southeast corner of the state of Tennessee. Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails. The shaft is 12 ft 7 1/2 in. ID of the concrete walls. This is large enough for two 10-ton hoisting skips and a ladder compartment. One of the skip compartments is for hauling equipment. The grouting equipment was a 2%xlO-in. Gardner-Denver grout pump, air powered and developing 1000 lb pressure. A grout mixer, also air driven, fed the mixed solution into a tank coupled to the pump suction. Grout materials used were mostly water and Portland cement. Some Bentonite was used to seal porous ground near the surface.

Jan 11, 1950

By C. W. Handy

ONE LAW cannot he evaded, the economic law of supply and demand. Silver, like any other commodity, is subject to this law; and its price in the long run is determined by existing conditions. I say "in the lone run because at times silver has appeared to mope contra to basic coalitions. Such movements, however, are, occasioned by the market&apos;s attempt to anticipate changes in these governing conditions. If the expected changes materialize then the new market level is justified, but if they do not then the market will revert to its previous status, A striking example of such a move occurred in November when the price advanced over 70, in ten days and then in the next two weeks lost more than it had gained. The reasons for this advance were that the speculative element interpreted certain events as favorable to silver namely, England suspension of the gold standard, higher shat prices, and the Chinese-Japanese crisis. When these expectations proved unjustified the inevitably, elapse followed became the governing conditions had not channel.

Jan 1, 1932

By Joseph W. Richards

ALTHOUGH bad grammar, the above query is probably, at the present moment, good sense. Why was the Institute started and why does it continue to exist? The small group of men who worked out the original idea felt keenly the necessity of mining engineers and metallurgists getting together in order to discuss their professional problems. That necessity still exists but it does not strike the present generation of engineers so keenly because they have always had the Institute: they do not know what it is to be without it. The Institute is a great graduate school of mining and metallurgy. All of its members who have something to say worth saying are the teachers; all the rest may be learners or critics. No university or technical school can match the experience and information which the authors of its papers possess, no institution of learning has a body of potential listeners so extensive and so vitally interested.

Jan 1, 1921

By John A. Gann

WITHIN a very few years magnesium has sprung from oblivion, from classification as a technically unknown, little appreciated, and expensive material to front-page importance in many fields of engineering. Bunsen may be considered the real founder of our present magnesium industry. In 1852; he prepared this metal by the electrolysis of fused magnesium chloride in a porcelain crucible. In the following years the electro¬lytic process became recognized as superior to chemical reduction methods and Germany became the world&apos;s chief producer, installing the first electrolytic magnesium plant in 1886. &apos; Thirty years later, national defense requirements, occasioned by the outbreak of the World War and the cutting off of imports, caused France, England, and the United States to begin production. Most of this magnesium was used for military purposes so the close of the war resulted in a large curtailment in production. A few companies, however, encouraged by the early success of the Germans and by the rapid developments taking place in aeronautics, and confident in the certain future and ultimate value of this metal, undertook extensive re¬searches in its production and utilization. A variety of production methods, both chemical and electrochemical, were investigated and some of them operated on a commercial scale. Reduction of the oxide with carbon at high temperatures and the electrolysis of the oxide in a fluoride

Jan 1, 1932

By W. E. STOKES

SOME extension of flying service to the mining industry occurred in 1938, particularly in Canada, where freighting activity radiated from Edmonton into the new northern mining districts. Again the airplane demonstrated its usefulness in getting new equipment rapidly into the field and in decreasing shutdown time while waiting for repairs. An 18-ton Caterpillar tractor with shovel attachment was disassembled, brought in by plane, and placed in operation at Berens River, Ont., within seven days after its de- livery at Winnipeg. At Central Patricia a mill breakdown required the replacement of a full mill head and trunnion with ball bearings, weighing 2700 lb. The Canadian Airways Junkers, termed the "flying boxcar," was called in from Yellowknife, 1300 mi. away, and the new installation was completed three days later.

Jan 1, 1939

By C. Wert, P. Bunn

Determination of the solid solubility of gases in metals is usually done by one of two methods. The first is an additive method, in which measurement is made at temperature of the maximum amount of gas absorbed by an initially degassed piece of the metal. Gas additions are made until the dissolved gas first comes into equilibrium with a compound. This method is most useful at relatively high temperatures where the amount of gas absorbed is relatively large and where equilibration of the dissolved gas with the gas atmosphere can be achieved in a relatively short time. The second is a precipitation method. A supersaturated solution of the gas in the metal is held at temperature until equilibrium is established between the gas atoms in solution and a compound. The quantity of dissolved gas is then determined by some physical measurement which is sensitive only to the gas in solution. This method is generally useful in low temperatures. This paper describes measurement of solubility of nitrogen in tantalum whereby measurements at low temperatures using internal-friction methods are plotted together with existing measurements at high temperatures. The solubility is thereby known from less than 0.5 at. pet at 350°C to near 13 pet at 2300°C. Several measurements have been reported of the solubility of nitrogen in tantalum. These are collected in Fig. 1. Three single determinations by Ke,1 Andrews,2 and Brauer and zapp3 are plotted along with a series of measurements by Vaughn, Stewart and schwartz4 and Gebhardt, Seghezzi, and Fromm.5 Although not much doubt exists about the solubility being in excess of 10 at. pet above 2000°C, the solubility indicated at low temperatures depends on whose data are selected as being most reliable. The variation is enormous, being at least an order of magnitude at 500°C. Accordingly, a measurement was begun to examine this discrepancy. The method of measurement finally selected was that of internal friction. A solid solution of nitrogen in tantalum was prepared by heating a tantalum wire in a dilute at-

Jan 1, 1964

By Walter C. Holmes

IN the recently published book entitled "Man in a Chemical World," by A. Cressy Morrison, the several pages discussing explosives were included in the chapter on "Serving Industry." Such a classification is entirely correct, as blasting explosives function only as a tool for accomplishing certain useful work, a tool which is completely destroyed in one use. Explosives are so important to industry and to modern society, in fact, that it seems impossible to imagine the existence of civilized nations without access to commercial explosives as ready servants. Two main types of explosives are now in use, the low-velocity or deflagrating type, such as black powder, which is adapted for use in coal mining and other applications where a slow, heaving effect is desired, and high explosives of the dynamite type,

Jan 1, 1938

By P. Barnes

EXACT accounts have been kept of the cost of these chimneys, and it may be a matter of some possible interest that the plans and details of cost should be laid before the Institute. The statement of cost herewith submitted does not give minute particulars of the weights or quantities of material used, although these are noted upon the company&apos;s books.

Jan 1, 1876

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn&apos;s for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

By T. W. Guy

DURING the past three years the Surface Preparation Committee of the American Mining Congress Coal Operators&apos; Committees has been collecting data on dewatering and drying washed coal, and on screening coal in representative plants in the Eastern and Central bituminous fields. Because of wide variations in bed moisture, such data can be compared only after deducting the bed moisture. It was found that practically every company used a different routine for moisture sampling and determinations. Some reported the moistures as total moistures, others as surface moistures, cur-dried moistures, or oven-dried moistures. For most of the reports it was necessary to esti-mate, from a consideration of the bed moisture and other data available in a given case, corrections to be made in order to obtain surface-moisture figures as a common basis for comparison. At any plant, and regardless of bed moisture, the percentage of surface moisture remaining in a product when the dewatering, or a given stage of the dewatering, has been completed, is the real measure of what has been accomplished. The descriptions and data given with Fig. 1 show that surface-moisture figures show relationships that would not be shown by total moistures. Therefore bed moisture should be deducted, or, if more practicable, the surface moisture of the. products should be meas-ured direct. A preparation engineer finds one per cent, or even a part of one per cent, of surface moisture a very important consideration in the results of his efforts to find the most effective and economical methods of reducing and controlling the surface moisture in his products within the required limits. Therefore it is important for him to have accurate measurements of surface moisture with minimum uncertainty as to whether they some-times include less than the surface moisture and at others all of the surface moisture plus an unknown part of the bed moisture.

Jan 1, 1938

By Charles Catlett

While the occurrence of phosphorus in coking-coal has assumed less importance with the development of the opeu-hearth method of steel-making, it may not be without interest to note the form in which phosphorus exists in one particular coal-seam. In the examination of what is known as the Big seam, which outcrops a few miles west of Columbiana, Ala., my attention was called to the distribution through the coal, in the form of minute veins and particles, of a resinous-looking substance. A small amount of this was selected, and was provisionally identified as evansite (Al6 Y2 O14, 18 Aq). Subsequently, through the courtesy of Dr. J. Sharshall Grasty, of the Geological Department of the University of Virginia, I was able to secure an additional amount of material, which was purified down to about 0.3 g. This was examined by Prof. John J. Porter, of the University of Cincinnati, and gave the following partial analysis: Per Cent. Loss on ignition,......... 37.43 Phosphoric anhydride,..10.33 Alumina,..........36.33 There was also a trace of silica, and quite a considerable quantity of lime and magnesia. Professor Porter was led to think that the material was not pure, but a mixture of several of the phosphates of aluminum carrying lime and magnesia. The material available did not permit of the convenient determination of the other ingredients. One form in which phosphorus occurs in coal is evidently as a hydrated phosphate of aluminum; and any coal which shows to the eye the occurrence of a light-colored resinous-looking material should be looked on with suspicion as being high in phosphorus.

Jan 1, 1912

J. S. UNGER,* Pittsburg, Pa, . (written discussion?).-The author of the paper has given an excellent description of the appliances used to cool parts of an open-hearth furnace, and some of the reasons why the refractories fail in service. Personally, I favor water-cooling, but to a limited degree. At one time I advocated more universal cooling than is now practised, but believe I must change my mind. Water-cooled, thin-lined blast furnaces have not proved as satisfactory as anticipated. While this may retard the building of many such furnaces, it will not prevent the use of regular tuyere- and bosh-cooling appliances. Water-cooling any furnace may be easily carried to the extreme. In an open-hearth furnace, excessive port or roof cooling, or cooling the working floors may preserve the lines of the furnace, lower the cost of refractories, acid to the comfort of the workmen, and necessitate fewer shutdowns for repairs, but it may not be good economy on account of the high first cost, the cost of cooling water, maintenance of cooling appliances, and the immediate reflection in a higher fuel cost. The question becomes a financial one, and is answered by using water-cooling devices up to the point at which they cease to show true economies. Open-hearth furnace bulkheads, roofs, and ports fail rapidly in about the order named. If they could be made to last indefinitely by water-cooling, the furnace would still have to be shut clown periodically for cleaning the slag pockets, regenerator chambers, and flues. Extra, or spare, pockets and regenerator chambers have been advocated to permit of continuous operation, but the space required, the cost of installation, and the fuel required to initially heat such cold chambers will largely prevent their adoption. Some particular fuels, as high-ash powdered coal, require frequent stoppages for cleaning, but for this particular fuel a special provision can&apos; be made.

Jan 5, 1919