Search Documents

By William L. Fink

Nickel is used as an alloying element in several complex commercial aluminum alloys, among which are found some very interesting properties, such as relatively high strength at elevated temperatures, relatively low coefficient of expansion, the absence of permanent growth, ability to take a good polish, and a bright, pleasing as-cast surface. For that reason the aluminum-nickel system was included in the list of binary aluminum systems that are being studied as a preparation for the investigation of more complex commercial alloys. This paper is the fifteenth of a series from the Research Laboratories of the Aluminum Company of America reporting the results of investigations of equilibrium relations in aluminum-base alloys of high purity. The aluminum-nickel equilibrium diagram from 0 to 18 per cent nickel was determined, using the purest material available. Previous Investigations The entire aluminum-nickel system was studied thermally and microscopically by Gwyer.1 At the aluminum end of the system he found the intermetallic compound NiA13. He found a eutectic at 6 per cent nickel with a melting point of 630" C. A slight thermal arrest, which he could not explain, was also noted in alloys from 2.5 per cent to 41.9 per cent nickel at 550" C. Bingham and Haughton,2 in a later investigation of alloys of aluminum with copper and nickel found the eutectic concentration of the binary aluminum-nickel system at about 5.3 per cent nickel. The melting point of the eutectic was about 633" C., or slightly higher than that found by Gwyer. Although the solid solubility of nickel in aluminum could not

Jan 1, 1934

By Blair R. Benner, Ronald J. Roman

The rate of acid leaching of malachite from a sandstone ore was shown to be controlled by the diffusion of H+ ions through the host rock. The kinetics of the reaction can be expressed by a shrinking core model. Equations for calculating effective diffusivities from an "infinite" slab and a cylindrical core were derived. The effective diffusivity, of H+ ions in a sandstone ore was measured.

Jan 1, 1975

By M. Schwartz, S. K. Nash, R. Zeman

Knoop hardness in the rolling plane and in the longitudinal plane of hot-rolled and cold-rolled sheets of sublimed magnesiu?w was measured as a function of the angle between the long axis of the indenter and the rolling direction. These measurements were correlated with similar data taken on the (0001) and (1010) planes of a single crystal of magnesium where the hardness was measured as a function of the angle between the long axis of the indenter and the [1120] direction. The results were analyzed for compliance with the hypothesis of Daniels and Dunm to account for slip, and with a similar hypothesis to account for twinning. Some hardness anisotropy data are also presented for magnesium-indium and magnesium-lithium solid solution alloys. It is well known that the hardness of a crystalline specimen is different for its different surfaces, and also that the hardness is a function of direction within a single surface. Variations in hardness for single crystals have been found to be much larger than those for polycrystalline materials. Also, materials having low crystal symmetry were found to have a greater anisotropy of hardness than those of high symmetry. 0'Neill1 and Pfeil,2 using a 1-mm Brine11 ball, studied single crystals of aluminum and iron, respectively; and they found a variation of hardness of about 10 pct between readings taken along the principal crystallographic faces. Daniels and Dunn3 found that the Knoop hardness number varied about 25 pct as the long axis of the indenter rotated on the basal plane of a zinc single crystal. The variation on the (1450) plane was about 100 pct, and the average hardness on this plane was about twice that of the basal plane. They also studied the variation of hardness within the (loo), (110), and (111) faces of a single crystal of silicon ferrite and found variations of about 25 pct although the average values for these planes were almost identical. Single crystals of zinc were also studied by Meincke.4 He found that the Vickers hardness numbers varied about 30 pct depending on whether the axis of the indenter was parallel or perpendicular to the (1010) and (1110) planes. Mott and Ford,5 using a Knoop indenter, found a 25 pct variation in hardness on the basal plane of zinc. Crow and Hinsley6 studied heavily cold-rolled bronze, steel, brass, copper, and other metals. They found that the difference in hardness numbers based on the difference in the length of the diagonals of the Vickers indenter was from 5 to 12 pct. Some minerals and synthetic stones show a very large anisotropy of hardness. Robertson and Van Meter7 found the Vickers hardness of arsenopyrite to vary from 633 to 1148 kg per mm2. stern8 using the double-cone method on synthetic corundum found the hardness number to vary from 950 to 2070. And winchell9 reported a variation of hardness number from 184 to 1205 in kyanite. The variation of hardness as a function of direction in a given crystallographic plane in single crystals possesses a periodicity which is related to the symmetry of the lattice. Daniels and Dunn3 found a six-fold periodicity of hardness in the (0001) plane of zinc. They found that the hardness curves of silicon ferrite had a four-fold symmetry in the (100) plane, a two-fold symmetry in the (110) plane, and a six-fold symmetry in the (111) plane. Mott and Ford5 also reported a six-fold symmetry of hardness in the basal plane of zinc. And vacher10 found two-, four-, and six-fold periodicities of hardness in copper on the (110), (100), and (111) planes, respectively. The purpose of this paper is to report the results of an investigation on the anisotropy of hardness as a function of orientation in single crystals of mannes-ium, and samples of rolled magnesium, magnesium-indium, and magnesium-lithium solid solution alloys. The anisotropy of hardness of pure magnesium which had been hot rolled, and then cold rolled various amounts to fracture, was studied by means of Knoop indentation hardness numbers; and the results were correlated with the preferred orientation as determined by quantitative X-ray pole-figure data. A comparison was made of the hardness data obtained from the rolled sheets and those of single crystals of magnesium. In order to obtain a more fundamental understanding of the variation of hardness and of Knoop hardness testing, the data were analyzed by

Jan 1, 1962

By R. M. Jorda

The mechanism of parafin deposition and prevention has been studied in the laboratory using an apparatus which provides a quantitative means of studying parafin deposition on metal and plastic surfaces. The amount, hardness, adhesion, per cent wax and mean molecular weight of parafin deposits appear to be governed by surface roughness alone, all other conditions being constant. Tests of various plastic coatings indicate that most smooth, nonparafinic plastics are capable of reducing parafin deposits in oil wells, but flexible, highly polar, nonparafinic plastics are more suitable for providing long term resistance to parafin deposition in oil wells if the flow stream contains abrasive materials. INTRODUCTION The problem of paraffin deposition is one of long standing in the oil industry.' Crude oils often contain paraffins which precipitate and adhere to the liner, tubing, sucker rods and surface equipment as the temperature of the producing stream decreases in the normal course of flowing, gas lifting or pumping. Heavy paraffin deposits are undesirable because they reduce the effective size of the flow conduits and restrict the production rate from the well. Where severe paraffin deposition occurs, removal of the deposits by mechanical, thermal or other means is required, resulting in costly down time and increased operating costs. The troublesome paraffins are normal hydrocarbons ranging from approximately C15H38 to C38H78 mixed with small amounts of branched paraffins, monocyclic paraffins, polycyclic paraffins and aromatics.' The amount of paraffins found in crude oils varies from less than 1 to more than 30 per cent. Many publications are available which deal with this problem, and perhaps the most significant findings in recent literature are contained in a publication by Hunt3 ho developed the "cold spot tester", a really useful means of investigating paraffin deposition. Hunt's observations led to many generalized conclusions concerning the effect of surface roughness on paraffin deposits. He ascertained that there was an observable qualitative correlation between the severity of paraffin deposition and the roughness of the surfaces which he tested (cold rolled steel, stainless steel and several plastics). Because of the number of meaningful observations made by Hunt, his cold spot tester was modified somewhat and extensive tests were per- formed to study the quantitative relationship between surface roughness and the physical and chemical nature of paraffin deposits. LABORATORY TEST PROCEDURES The cold spot test apparatus consists of a flat circular plate mounted on a curved tube and positioned in a vessel containing a wax-oil solution (Fig. 1). The apparatus is arranged so that the temperature of the central portion of the circular plate can be varied by means of a circulating liquid stream; the test equipment includes provisions for maintaining a constant wax-oil solution temperature and stirring speed. In the paraffin deposition studies, the modified cold spot tester was used as follows. The cold spot probe consisted of a flat circular plat 2 in. in diameter and 1/8-in. thick positioned in the wax-oil solution kept at constant temperature. As in Hunt's earlier experiments," a cold liquid was circulated through a tube connected to the circular plate so that the liquid impinged on one side of the plate cooling the plate from the center outward, causing paraffin to deposit on the side of the plate exposed to the wax-oil solution.

Jan 1, 1967

By J. O. Edstrom, G. Bitsianes

Parabolic rate constants were determined for the formation of wiistite by the solid state reaction between magnetite and iron. The reaction was diffusion controlled and inert marker studies indicated that the mass transport through the wiistite layer was accomplished by means of iron migration. Relationships between rate constants and self-diffusivities are discussed. The transport capacity for iron through dense wustite layers was found to be sufficient to carry on reduction, even in gaseous reduction processes. REDUCTION of iron oxides has been the subject of many investigations. Most of the work, however, has been done on rather crude material and there have been difficulties in correlating the data on a quantitative basis. The reverse process of the oxidation of iron has been studied more thoroughly and usually by starting from the pure metal. As a result, the mechanisms of oxidation are now fairly well known.It has generally been found that the oxidation of metals follows the so-called parabolic 1aw;Q hat is, when the oxides are formed as dense layers, their thicknesses are proportional to the square root of the reaction time. This parabolic law follows directly from Fick's first law of diffusion The flux, J, is defined as the quantity of diffusing substance passing per unit time through unit area of a plane at right angles to the direction of diffusion. This flux is proportional to the concentration gradient of the diffusing substance, and the factor D, known as the diffusion coefficient, is introduced as the proportionality factor with dimensions of (length)'/time. If the flux is measured as the increase of thickness of the oxide layer (Ax) per unit time (t) and the assumption is made that the concentrations of the reactants at the phase boundaries of the layer are independent of time, Eq. 1 reduces to Integration of this expression yields the parabolic function ax = k . t. [31 The product of the diffusion coefficient and the concentration difference across the oxide layer is included in the constant k. When iron is exposed to a highly oxidizing atmosphere, the oxide phases are formed normally in a topochemical fashion, i.e., the interfaces between the phases maintain parallel positions to the original surface of the specimen. Above 570°C, the phases are orientated usually in the order of iron, wiistite, magnetite, and hematite, a condition in conformance with the requirements of the Fe-0 system. Below 570°C, the wiistite phase is unstable and has not been found as a normal constituent in the oxidation products of iron. There is a strong probability that continuous layers of the solid oxides are formed as the specific volumes of the phases increase in direct order from iron to hematite.' , ' Regarding mass transport through dense solid oxide layers, Wagner' has postulated that diffusion in oxides generally may be interpreted as migration processes of ions and electrons. There must be normally a concentration gradient across the growing oxide layer for diffusion to occur. This condition requires that there be deviations from the ideal stoi-chiometric composition of the oxide and accordingly deviations from the strict order of an ideal lattice. Such "lattice defects" include interstitial ions, cation and anion vacancies, quasi-free electrons, and electron holes and are decisive for all migration processes.' Cations, anions, and electrons all may have some mobility in the oxides but the movement of one of the particles generally far exceeds that of the others. Previous work', 1,2,7 has shown that during the oxidation of iron the migration through the wiistite layer, and probably also the magnetite layer, is confined to the movement of iron ions. Migration through hematite, however, has been found to take place by oxide ion movement. These behaviors are in direct agreement with the type of vacancies present in the respective oxides. Reduction of Iron Oxides The gaseous reduction of iron oxides, like the oxidation of iron, takes place in a topochemical fashion at distinct interfaces between the appearing phases."-'" Porosities might be expected in these reaction products, since their specific volumes are less than that of the starting material. Frank and van Der Merwe" have shown, however, that it is theoretically possible for nonporous layers to form if the degree of misfit in specific volume is less than about 15 pct. These aspects on porosity formation

Jan 1, 1956

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946

By Pol Duwez

IN the course of an investigation of the V-CO system, two intermediate phases were found. One of these phases corresponds approximately to the stoichiometric composition VCo and is isomorphous with the sigma phase in the Fe-Cr system.' The second phase has the composition V3Co; its crystal structure is described in the present note. The alloys were prepared by mixing the two metals in the powder form, pressing a small disk weighing about 5 g at 80,000 psi, and arc melting this disk on a water-cooled copper plate in an atmosphere of pure helium. The details of this technique have been described.' The vanadium powder was obtained from Westinghouse Electric Corp., Bloomfield, N. J. This powder is probably of very high purity, since when it is properly sintered or melted in the above-mentioned arc furnace, ductile specimens are obtained. The cobalt powder, from Charles Hardy, Inc., New York, contained 0.5 pct Ni, 0.1 pct Cr, and traces of Si and Fe. After melting, the V,Co samples were sealed in evacuated quartz tubes and homogenized for ten days at 800°C. Powder diffraction patterns were obtained with a 14.32 cm diam camera, using Ka copper radiation. The patterns were readily indexed on the basis of a primitive cubic lattice with a parameter equal to 4.675A. The density, determined by the immersion method, was 6.71 g per cu cm; hence the number of molecules per unit cell is approximately 1.95; i.e., 2. At this point, the possibility that the structure might be that of beta tungstena became apparent. The beta tungsten structure is described as follows: Space group 03,, — Pm3n 2 Co in (a) : 000; ?4lhYZ (hhl) reflection present only if 1 = 2n. Assuming this structure to be the correct one, intensities were computed by means of the usual eauation: 1 + cos220 I oc p F sin 0 cos 6 where F is the structure factor, 0 the Bragg angle, and p the multiplicity factor. The observed and calculated values of sin 0 and the intensities are given in Table I. The agreement between the observed and the calculated sin 0 is good and there are no flagrant discrepancies between the calculated intensities and those estimated visually. The (hhl) reflections for which 1 is odd are not observed, as required by the space group. In addition, the (410), (430), and (531) reflections are missing as expected, because of the special (a) and (c) positions in0%. However, six reflections—(llo), (220), (310), (411), (422), and (510)—which have very weak computed intensities were not observed. For these reflections, the structure factor is proportional to the difference between the scattering factors of the two atoms in the structure. Since the scattering factors of vanadium and cobalt are not very different, these reflections are weak. However, by using Ka chromium radiation, whose wavelength is just above the absorption edge of vanadium, the effective scattering factor of vanadium may be decreased by one or two units; consequently the difference between the cobalt and vanadium scattering factors is increased. It was, indeed, found that in a powder pattern taken with chromium Ka radiation, the three reflections (110), (220), and (310) were actually present. The three other reflections (411), (422), and (510), with spacings smaller than half the wavelength of chromium Ka, were obviously not obtainable with chromium radiation. All the experimental results appear to confirm the beta tungsten structure for V,Co. In this structure, each cobalt atom is surrounded by twelve vanadium atoms at 2.61A; each vanadium atom is surrounded by two vanadium atoms at 2.34A, four cobalt atoms at 2.61 A, and eight vanadium atoms at 2.86A. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under contract number W-04-200-ORD-455 with the Army Ordnance Department, Washington, D. C. The author wishes to thank this agency for the permission to publish the results of this investigation. References 'P. Duwez and S. R. Baen: X-Ray Study of the Sigma Phase in Various Alloy Systems. Symposium on the Nature, Occurrence, and Effect of Sigma Phase. ASTM Special Tech. Pub. No. 110, pp. 48-54. Philadelphia, 1951. 2 C. H. Schramm, P. Gordon, and A. R. Kaufmann: The Alloy Systems Uranium-Tungsten, Uranium-Tantalum, and Tungsten-Tantalum. Trans. AIME (1950) 188, pp. 195-204; Journal of Metals (January 1950). 3 M. C. Neuburger: The Crystal Structure and Lattice Constants of Alpha and Beta Tungsten. Ztsch. fiir Krist. (1933) 85, pp. 232-237.

Jan 1, 1952

By Morris Muskat

A theory is presented for calculating the performance history of complete water-drive systems producing from idealized stratified formations. The general equations are applied to systems where the permeability stratification is either of the exponential or linear type. Calculations were carried through for different degrees of permeability stratification, but with special emphasis on the effect of the mobility ratio between the produced oil and the invading water on the resultant performance. These results are also expressed graphically as curves for the initial water breakthrough recovery, for the different degrees of stratification, as a function of the mobility ratio, and of the composition of the produced fluid stream as a function of the cumulative oil recovery. For several typical cases the latter has also been plotted as a function of the cumulative oil and water throughflow. The general result is that when the mobility of the oil is lower than that of the invading water the channelling tendency resulting from the permeability stratification becomes aggravated as the higher permeability zones become flooded out. Situations of this type would obtain when producing low gravity or highly viscous oils. Conversely, if the mobility of the oil is high compared to that of the invading water, the flooding of the high permeability zones will lead to a retarding and choking effect, and the gross bypassing phenomena will be partially suppressed. These conditions would correspond to those of flooding high gravity or low viscosity oils. A discussion is given of the various basic assumptions made in the analysis, including that of ignoring the stripping phase of the production history as implied by relative permeability concepts. INTRODUCTION The physical ultimate recoveries from oil reservoirs are basically determined and limited by the physical oil displacement processes associated with the reservoir producing mechanism. In practice, however, the economic ultimate recoveries are further limited by the mobility of the reservoir fluids and the uniformity and continuity of the producing formation. In fact, it is the differential depletion between the component parts of the composite reservoir which ultimately determines the total recovery at the time of field abandonment. While this observation applies to both the solution gas drive and gravity drainage mechanisms, in which use is made only of the energy contained within the original oil-bearing reservoir, it is of even more paramount importance under operations wherein the energy associated with extraneous fluids provides the ultimate oil expulsion mechanism. Whether the invading fluid is the water from an edgewater drive, water injected for pressure maintenance, gas injected for pressure maintenance, or gas returned to the formation in a cycling program, it is often the continuity and uniformity of the producing section which will control the economic efficiency of the operations. The importance of the problem of reservoir non-uniformity does not, of course, lessen its complexity or the difficulties of its solution. In fact, these are inherently such that the concept of a "general" solution is virtually meaningless. About all that can be reasonably hoped for is the analysis of specific and well-defined types of non-uniformity which may give some degree of approximation to actual reservoir conditions. Since variations in the nature of the reservoir which depend only on the position along the streamlines will not lead directly to major differential depletion development within the reservoir, the types of non-uniformity considered thus far have involved stratification assumptions. That is, the producing section has been replaced by a multi-layer "sandwich," each uniform areally, and differing from the others only in its basic physical constants as to thickness, porosity and permeability. The fluid motion in the composite system is thus approximated by a parallel superposition of the independent fluid movements in the individual strata. For the specific application to cycling operations the theory of the effect of permeability stratification has been developed for both discontinuous' and continuous types of permeability stratification. Among the latter, treatments have been given of systems in which permeability distributions are governed by exponential, linear' or probability3 functions. In all these studies complete dynamical equivalence was assumed between the injected dry gas and the displaced wet gas. The overall effective permeability of each stratum was therefore considered as constant and independent of the degree of invasion of the injected fluid. In the case of the displacement of oil by water, the assumption of dynamical equivalence between the water and oil will be strictly valid only by accident. Even if the oil viscosity should be the same as that of the water, the effective permeability to the oil in the presence of the connate water will in general be quite different from that of the water behind the water-oil interface flowing past the trapped residual oil. As a result the effective permeability for the stratum as a whole and rate of water invasion will change with time as the intrusion continues. The differential fluid motion in the individual strata will thus also vary with time. Qualitatively, it is easy to predict the resultant effects. If the permeability to viscosity ratio of the invading fluid exceeds that of the fluid displaced, the stratification and bypassing effect of the perme-

Jan 1, 1950

By Karl Eilers

This process, invented by Messrs. Hanisch and Schroder, of Rosdzin, was patented in 1883. It has attracted considerable attention in Germany, as a very neat and simple method of extracting sulphurous acid from the gases produced by roasting, and of condensing this acid so as to obtain it in the very compact anhydrous liquid form. The special importance which such a process may have at this time in the United States is suggested by the growing inconvenience, amounting to distress, experienced in such localities as Butte, Mont., where the sulphurous gases from large roast-plants have proved not only fatal to vegetation but injurious to human health. It is reported that the authorities of Butte are earnestly considering the enterprise of removing, if practicable, the dense and suffocating cloud which now hangs over that city, and of which sulphurous acid undoubtedly forms the greater and most oppressive, if not the most poisonous, part. May it not be that the solution of this problem is furnished by a

Jan 1, 1892

By R. F. Hehemann, Darrell W. Smith

The kinetics of alloying- in W-5 rot pct Re powder compacts were investigated at temperature about the upper limit for the formation of the x phase, such that a single intermediate phase was involved in the process. The rates and directions of motion of the a-o and o-b interface were assessed as functions of tinze at the sintering teri7peraticve by quantitative izetallog-ralhic techtziques. The iiotion 01 these interjuces could be specified approxitnate1.y by u Parabolic )-ate law and deviations from this ,rate law were attribuled to a complex interaction between surface dif'fusion and volume diffusion during the initial stages of sintering. WHEN binary or more complex alloys are produced by sintering compacted blends of elemental powders, a complication is encountered which does not arise in the sintering of pure metals. In addition to concern for grain size and densification, the rate of inter diffusion of the component elements must be considered. The general problem of alloying during sintering has been treated by numerous investigators.'-7 These investigations have been concerned only with systems that form continuous series of solid solutions and a concentric-sphere diffusion model4 provides a useful description of homogenization in these stems.' Some controversy remains, however, over the contribution of surface and grain boundary diffusion to the homogenization process. Heckel% ePorts that homogenization can be described by volume diffusion at all temperatures, whereas other invetiators'' recognize the importance of surface and grain boundary diffusion, particularly at lower temperatures. Analysis of the homogenization process in partially miscible systems is complicated by the motion of the interfaces separating the individual phases. A simple analytical solution does not exist for such finite systems with spherical symmetry. It was the purpose of this work to examine the kinetics of the formation and dissolution of an intermediate phase in a binary system through an assessment of the motion of the interfaces separating this phase from the terminal solid solutions. PROCEDURE The W-Re system is an example of a partially miscible binary system and was selected for study because of its current importance in refractory-metal technology. The equilibrium phase diagram, Fig. 1, shows that the o phase will be formed by interdiffu-sion between tungsten and rhenium. At temperatures between approximately 2125" and 282O°C, the o phase will appear as the only intermediate phase in the diffusion system. In this work, a mixture of elemental powders containing 5 pct Re was employed. In such a mixture, the rhenium particles will be distributed randomly in a tungsten matrix. During sintering, a o-phase layer will form at the W-Re interface. The development and subsequent disappearance of the o phase are controlled by the relative rates and directions of motion of the 0-0 and a-p interfaces. The motion of these interfaces can be inferred from quantitative metallographic measurements of the average radii of the o shells surrounding rhenium particles. Elemental tungsten and rhenium powders of commercial purity were employed in these investigations. The rhenium powder was spheroidized from +200 mesh agglomerates by plasma-arc spraying and was then classified to yield a powder composed of essentially

Jan 1, 1967

By W. H. Blauvelt

THat the problem of utilizing anthracite waste is worthy of the thought bestowed upon it, may be shown in few words. In the year 1889, for instance, 35,408,000 tons of coal were sent to market from the anthracite regions of Pennsylvania. According to the report of the State Geological Survey, the amount of coal thrown on the dumps as waste, varies, with circumstancett, from 44 to 60 per cent. of that shipped to market. The lower of these figures represents 16,579,000 tons of waste for that year, and it is obvious that if this, or any considerable portion of it, could have been saved, it would have constituted an important addition to the fuel-supply of the country. It is not surprising, therefore, that so much attention has been given to the utilization of this waste. Among the many lines of experiment pursued with this object in view, the conversion of the carbon of the culm into producer-gas seemg at first to promise the most satisfactory solution of the problem. It is well known that in foreign producer-plants almost all kinds of

Jan 1, 1892

By David B. Reger

Oil and gas and their derivatives continue to be stable products in West Virginia. In the midst of the cataclysmic happenings of 1930 to 1934, which have swept away banks and practically destroyed many other enterprises of presumably nonspeculative character, the possession of a royalty or working interest in a few old oil or gas wells has prevented disaster in literally thousands of homes. These old wells yield their daily quotas of basic commodities, which the public must have. Fortunately, the facilities of disposal in the Appalachian Province are so ample and well managed that the owner of such equities may be reasonably certain that his proportionate share of existing markets will be afforded him without much effort on his part. In most cases these investments are free from encumbrance or hypothecation, therefore the main uncertainty is the date of ultimate exhaustion at the source. Generally, this is known to be fairly remote. The net result has been that individual owners part with such investments only as a last resort. In sharp contrast to the action of the small owner of wells or royalties who has prudently refrained from jeopardizing his rather certain income by drilling new wells that may be failures, or of which the product may not be needed for the moment, has been the plight of various promotional enterprises in natural gas. Many of these ventures have been operated by amateurish remote control and practically all have been overloaded from the start with bonds and debentures, which could only be satisfied in a rising and expanding market; and with operating costs that have been exceedingly high because of widely scattered producing units and large overheads. Many of these promotions are now in receivership or bankruptcy and in various instances the original units have been recaptured by former owners and have again become profitable by reason of personal operation and elimination of all forms of overhead expense. New Development In 1934, the State issued 524 permits for drilling. According to the trade journals, 553 wells were completed, with 184 oil wells, 274 gas wells and 95 dry holes (Table 3).

Jan 1, 1935

By S. Leber

Pole figures and pole distributions were used for the quantitative detevinination of the preferred orientations in swaged tungsten rods and the effect of subsequent wire drawing on the texture. In the swaged rod, the preferred orientation could best be described as a pseudo (111-112) [110] cylindrical texture. A secondary component was assigned the indices (110) [001]. Further reduction by swaging retained these cylindrical textures. Wire drawing caused lattice rotations about the wire axis, converting the cylindrical texture into a normal fiber texture. The conversion was initiated and proceeded lnost rapidly in the center of the wire. The (110) /001] component was converted into a (110) fiber texture by wire drawing. The effective rotations were about axes contained in the lransverse plane. The preferred orientation associated with tungsten wire usually has been assumed to consist of a (110) fiber texture. This implies rotational randomness around the wire axis. Leber1 has shown that rotation about the wire axis may be restricted resulting in a preferred orientation designated as a cylindrical texture. Specific crystal planes tended to remain aligned parallel to the wire surface. This texture seemed to be the result of the swaging operation used in the intermediate stages of fabrication. Bhandary and cullity2 detected similar textures in swaged iron wires. Peck and Thomas3 suggested that the preferential alignment of crystal planes parallel to the wire surface was the result of tangential flow, characteristic of swaging. Wire drawing, following swaging, twisted the crystals about axes parallel to the wire axis, converting the cylindrical texture into a normal fiber texture.4 In this investigation, quantitative techniques were used to more accurately characterize the cylindrical texture and to study its conversion into a normal fiber texture. PROCEDURE The material investigated was lamp-quality tungsten. Three ingots were rod-rolled and swaged to 112 mils diameter, and were then drawn to 10-mil wire. Samples were obtained after each drawing pass. (110) and (200) pole figures were obtained from samples prepared as shown in Fig. 1. To form the sample shown in Fig. l(a), l-in. lengths of wire were glued side by side to form a l-in. square. The composite was ground and electropolished to form a diametral reference surface. For certain specific tests, samples were prepared as shown in Fig. l(b). This composite was made from 10-mil-thick strips prepared by grinding on parallel longitudinal planes. The polished reference surface in this case was, in essence, the wire surface. The two forms of samples [~igs. l(a) and l(b)] were related by a 90-deg rotation around the wire axis. Because of ease in preparation, most data was obtained from the diametral samples. The X-ray data were obtained using a Siemen's pole-figure goniometer. These data were not corrected for absorption or defocusing effects, since only the angular locations of the intensity maxima were of interest. Regions of the pole figure more than 80 deg from the center were not investigated. Partial monochromatization was achieved by the use of unfiltered copper radiation and a krypton-filled proportional counter. No evidence of spurious white radiation effects5 could be detected. Therefore, more elaborate X-ray techniques were not required. Intensity levels were chosen to show all pertinent details of the orientation distributions. The reference plane for the pole figures was the diametral section. The orthogonal reference directions, shown in Fig. 1, were the wire axis, the radial axis per-

Jan 1, 1965

By N. A. Gokcen, R. A. Dodd

Solubility of nitrogen in liquid iron-manganese system at 1550°C and one atmosphere pressure has been determined by a simple method. Results show that the solubility increases from 0.040 pct for pure iron to 1.41 pct for pure manganese. DETERMINATION of the solubility of gases in volatile metals. and alloys by the well-known Sievertsl method is unreliable. This is particularly true for the Fe-Mn system since Mn vaporizes readily from the alloys containing as little as 2 pct Mn, and, upon condensing on the cooler parts of the apparatus, it absorbs large amounts of nitrogen. Further, the condensing Mn vapor interferes with the usual method of temperature measurements with an optical pyrometer.

Jan 1, 1962

By Y. C. Liu, H. Margolin

Investigation of martensite habit plane in water-quenched Ti-Mn alloys was carried out in the range of manganese contents between 4.35 and 5.25 pct. On the basis of 22 measurements, the poles were observed to fall into two groups, indicating the existence of two habit planes. The Miller indices of the poles close to these two groups were found to be <334>ß and <344>ß. TITANIUM has an allotropic transformation at 882.1° ± 0.5C1 by which the high temperature ß (body-centered cubic) phase changes to a (hexagonal close-packed) phase. It is well known, as in the case of low carbon steel, that the unalloyed high temperature ß phase cannot be retained no matter how rapid the cooling rate. However, the addition of alloying elements usually lowers the transformation temperature continuously and stabilizes the ß phase to a temperature much lower than the allotropic transformation temperature in pure titanium. A typical example of this behavior is found with manganese-alloying of titanium. Fig. 1 shows the titanium-rich Ti-Mn equilibrium diagram as established by Battelle Memorial Institute.&apos; The addition of manganese lowers the ß transus line and the eutectoid reaction takes place at 550°C, the eutectoid composition being 20 wt pct Mn. However, upon quenching to room temperature from the ß field, the ß phase can be completely retained with much less manganese, see Fig. 2. If the composition is less than that required to stabilize the ß phase completely, a plate-like structure, similar to that of martensite in other alloy systems, appears as shown in Fig. 3. Much lower alloying content merely intensifies the amounts of these transformed structures, as shown in Fig. 4. This paper presents the results of an investigation of the habit plane of these martensitic structures in Ti-Mn alloys. Experimental Procedure Investigation of the pole of a given platelet was made using the two-surface method of analysis." In order that a given martensite trace on two surfaces be readily recognized both at low and high magnifications, it is desirable that only a small amount of martensite be present. From a review of the data obtained at Battelle Memorial Institute4 on quench hardening in Ti-Mn alloys and the results of Duwez" on transformation in Ti-MO alloys, it was decided that the most appropriate Ti-Mn composition for this study would be about 6 pct Mn. A group of alloys containing from 3 to 10 pct Mn was made to bracket this composition. The choice of the 6 pct alloy was apparently proper, since it was later learned that approximately 5.5 to 6 pct Mn is required to stabilize the ß phase on water quenching.

Jan 1, 1954

By Juptner von Jonstorff

A discussion of the paper by Messrs. Jüptner von Jonstorff, Blair, Dillner and Stead, read by title at the Lake Superior meeting, but presented first at the New York meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement between the two Institutes. Correspondence. MR. R. HAMILTON (Glengarnock) wrote to say that it was known for many years, that unless certain precautions were taken in dissolving the sample, there was a liability to obtain a solution from which the ammonium-molybdate solution would not precipitate the whole of the phosphorus. In 1877 Blair and Finkiner independently attributed this interference to the presence of carbonaceous matter in the solution, derived from the action of acids on the combined carbon of the metal, and they directed that the solution should be prepared in such a manner as to destroy these carbonaceous compounds. This was practically effected by evaporating the acid solution to dryness and roasting the residue. Adolf Tamm, in 1884, accentuated the same view. There are methods founded on the above-mentioned observations which leave nothing to be desired in point of accuracy, but the evaporation to dryness with subsequent roasting and re-solution consumes much time, besides the minor inconvenience caused by large amounts of acid fumes. In 1888 P. W. Shinier suggested that the incomplete precipitation of phosphorus was due to incomplete oxidation of -.the phosphorus, and proposed to render all the phosphorus precipitable by oxidizing the solution with potassium permanganate, etc. Experiments were made to test the accuracy of this view (details will be found in the Journal of the Society of Chemical Industry, vol. x., p. 904), and the results obtained seem to-prove that it is the correct one. It was first proved that carbonaceous matter in solution did not prevent the precipitation of properly oxidized phosphorus

Mar 1, 1905

By R. H. Richman

Coarse-grained Fe-Ni-C martensites formed at subzero temperatures were strained in compression at room temperature and the plastic deformation modes examined as a funclion of carbon content. At very low carbon levels, defovmation occurs hy wavy slip; commencing at about 0.05 pct C, mechanical twinning accounts for an increasing proportion of the plastic flow. Beyond approximately 0.4 pct C the deformation appears to be entirely by mechanical twinning. The habit planes of the operative twin modes were determined to be (113), (0131, and "(089)" in decreasing frequency of occurrence. Some of the implicaticms of Ihe o6served deformation modes upon the structure and properties of ferrous martensites are discussed. METALLURGISTS have long sought to explain the mechanical properties of ferrous martensites, particularly the extraordinary hardness and strength of the high-carbon varieties. Until recently the lack of precise knowledge of the structure of martensite crystals was the most serious barrier to understanding; however, the advent of thin-foil techniques for transmission electron microscopy has removed much of the mystery from martensite structure. Observations by Kelly and Nutting,"&apos; and many others since, indicate that Fe-C based martensite crystals are internally twinned to a degree dependent upon the carbon content, and that a martensite plate containing 0.8 wt pct C or more consists of a stack of twin-related lamellae with each lamella on the order of l00A thick. Such a structure would be expected to influence greatly all aspects of metallurgical behavior, and many of the properties of Fe-C based martensites have been rationalized accordingly. Recent independent experiments led Winchell and cohen3 to conclude that the strength of ferrous martensite is derived primarily from solid solution hardening of the iron lattice by interstitial carbon atoms. Strength contributions from precipitation, dislocation-atmosphere interactions, clustering, short-range order, crystallite size, and so forth, were considered to be of secondary importance. In the view of Winchell and Cohen, the twinned structure of martensite serves mainly to limit the effective length of dislocation lines in the lattice, and thereby confers an added measure of hardening. Few properties of metallic crystals are as sensitive to metallurgical structure as are deformation mechanisms. It is somewhat surprising therefore, that, except for metallographic evidence of mechanical twins in strained martensite,4 no systematic examination of plastic deformation

Jan 1, 1963

By H. J. Hand

STATISTICAL methods are becoming increasingly important for inter-preting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor,1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.-Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of vari-ables more or less constantly tending to affect it. As pointed out by Daeves, 2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such plants. ?

Jan 1, 1938

By J. E. Hilliard, J. W. Cahn

In this paper it is suggested that the degree of contiguity (or contact) between adjacent grains be described by three parameters which can be rigorously determined from measurements on a random plane of polish. An expression is also derived for the number of contacts per unit volume and it is shown that this quantity can-not, in general, be estintated from measurements on a random plane. IN a recent contribution1 Gurland has proposed various parameters for describing the degree of contiguity (or contact) between grains of the same phase in an alloy. To relate these parameters to measurements on a random two-dimensional section, it was necessary in most cases to make some assumption about the form of the structure. Since Gurland was specifically interested in sintered carbide structures, he chose, quite reasonably, to assume that the grains were constant-size spheres and that all the intersections were flat areas of constant radius. Since, as we will show, the relationships between the parameters and the measurements are strongly dependent on the grain shape and size distribution, it is evident that these assump tions will not be satisfactory approximations for a

Jan 1, 1960