Search Documents

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By Alden B. Greninger

That metallographic structures analogous to the martensite of steel may be found in certain copper-aluminum and copper-tin alloys has been known for many years; similar structures recently were found in certain copper-zinc a1loys.l In all three of these alloy systems the martensite structures result from transformation of the metastable fi phase when the speed of cooling from the B range is sufficiently high to suppress decomposition into equilibrium phases. In the normal decomposition of solid solutions into equilibrium phases, diffusion is needed to bring about the necessary changes in concentration, and the rate of reaction falls almost to zero at temperatures slightly above room temperature. The rates of reaction for martensite processes, however, are not dependent upon temperature; the transformation does not require rendjustments of concentration. For example, the martensite transformation in 60:40 (B) copper-zinc does not begin until the temperature has dropped to about minus 30" C., and then continues down to minus 130" C. and probably even at lower temperatures.' Furthermore, martensite processes apparently proceed only while the tempcrature is falling, within the proper range, and cease completely while the temperature is held constant ;$ and they cannot be suppressed by extremely rapid cooling although the rate of cooling for some alloys may be increased to over 10,000 times the critical cooling velocity. Isaitschew, Kaminsky and Kurdjumow2 account for these observed behaviors of rnartensite processes by postulating that the mechanism 6I... consists in a regular rearrangement of the lattice in such a way

Jan 1, 1939

By R. P. Rothwell

The milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I hare thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value arid interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a met stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulplides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is managed in a skilful and economical manner, though the necessity for

Jan 1, 1880

By J. B. Newkirk, R. W. Hendricks, R. Baro

STUDIES of the kinetics of precipitation in binary alkali halide systems are of interest from a theoretical point of view, because of the possibility of controlling diffusion rates by additions of aliovalent impurities. This note reports some preliminary results of a study of the kinetics of precipitation of AgCl from supersaturated solid solutions of AgCl in NaCl containing trace amounts of divalent cation impurities. In their study of the system NaC1- AgC1, Stokes and Li1 derived the phase diagram containing a mis-cibility gap with a broad maximum at approximately 170°C. They found that single crystals quenched from above the miscibility gap and aged at various temperatures within the two-phase region gradually turned light blue, then cloudy white, and finally opaque. The rate of transformation depended markedly on the aging temperature. The light-blue color in the early stages of aging was interpreted to be the result of Rayleigh scattering from precipitated particles less than 0.1 µ in diameter. These qualitative observations have been confirmed by us. However, a more precise tool was needed in order to quantitatively follow the growth kinetics of the precipitate particles. Because of the suspected small size of the precipitate particles and for other reasons, small-angle X-ray scattering was thought to be a suitable technique for this study. Small-angle X-ray intensities scattered from powder specimens were recorded on a General Electric XRD-5 diffractometer using the four-slit geometry described by Neynaber, Brammer, and Beeman.2 The slits were 0.08 mm wide by 10.00 mm high. It was found that, with very careful alignment, meaningful data could be obtained to within 3 min from the middle of the direct beam. Chromium radiation (?Ka = 2.29Å) was used in order to spread the scattered intensity to a relatively high angle, as indicated by Eq. [1]. A specimen containing 21.0 at. pet AgCl was prepared by melting analytic reagent-grade AgCl and NaCl under a chlorine atmosphere in a vycor cap-

Jan 1, 1964

Mr. Raden has described the practical problems associated with fines in phosphate rock beneficiation. In this discussion, a colloid chemical viewpoint is given to the problem of separating phosphate values from phosphatic clay slurries. The phosphatic clays are predominantly colloids of a complex mixture of many minerals (1). The constituents are typically 25% apatite, 40-50% clays, and various amounts of wavellite, quartz, dolomite, fluorite, and other minerals. The clays are montmorillonite, attapulgite, and illite, with some kaolinite. The various mineral colloids in the slurry are heterogeneously coagulated in the as-produced state. Dispersion of the coagulated state is evident from the fact that dispersing agents (certain polyelectrolytes) cause a large reduction in the viscosity of the slurry (2). The as-produced slurry settles from 4 to 8% solids within a week, but thereafter settles much more slowly in the form of a sediment of flocs. The supernatant liquid is often clear because of the cooperative action of the mutual interaction of particles during settling. Mineral segregation during settling has not been observed for the same reason. The initial slow settling rates indicate that the coagulated assemblies are very small. Efforts to separate apatite from the other minerals would be complicated by the heterogeneous coagulation state. Somehow the apatite must be "liberated" from its association with the other minerals before it can be physically separated. One approach for liberating apatite is to disperse the entire suspension. While this is feasible technically, for example by using certain polyelectrolytes (2), the reagent costs based on present

Jan 1, 1979

By V. G. Mooradian

THE diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distor-tion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-

Jan 1, 1935

By T. Saburi, C. M. Wayman

The massive and martensitic transformations in ß Cu-Ga alloys were studied by optical microscopy and by transmission electron microscopy and diffraction. These types of transformation are distinct and do not merge into one another. An internal fine structure due to stacking faults was found in both the massive phase (m) and the martensite, but the origin of the faults is believed to be different in each case. The faults in the martensite are due to the lattice invariant or "second" shear of the phenom-enological theory, while those in the are probably growth faults and deformation faults arising from the transformation volume change. Evidence is presented for ordering in the ß phase prior to transformation into martensite, and the crystal structures of and ß' and ßi martensites are discussed. THE results from some previous investigations1,2 have led to the suggestion that martensitic and massive transformations have certain common characteristics. It presently seems established that massive transformations like martensitic transformations are essentially diffusionless,1,2 but unlike martensitic transformations, when a new phase forms massively there is no shape change or surface relief.= If the massive-type transformation is crystallographically similar to martensitic transformations, one would expect a fine structure as a result of the lattice invariant shear4 which is a part of the transformation mechanism. The existence of such a fine structure (i.e., slip, twinning, or faulting), if any, can be verified by transmission electron microscopy, and thus the present investigation was undertaken to compare the internal structure of massively and martensitically formed phases in Cu-Ga alloys which were derived from a parent of the same composition. The transformation characteristics of ß Cu-Ga alloys were also studied. The bcc ß phase in the Cu-Ga system, Fig. 1, is stable above 616oc.' Depending upon the cooling rate, ß Cu-Ga alloys can undergo three different types of phase transformations. The ß phase of eutectoid composition (23.7 at. pct Ga) decomposes into the ? phase (hcp) and the phase (complex cubic) by means of a eutectoid reaction. When the cooling rate is increased so that the decomposition of 0 into [ and ? is suppressed, the ß phase transforms into a nonequilibrium hcp phase, herein denoted ?m by a process of very rapid growth called a "massive" transformation. At even faster quenching rates the massive transformation can be suppressed and the ß transforms martensitically. Massive transformations, apparently similar to those in the Cu-Ga system, have also been studied in the Cu-Zn2,6-8 and Ag-Cd systems.9 Definitive characteristics if the Massive Transformations in 0 Cu-Ga Alloys1 1) The most remarkable feature of the massive transformation in Cu-Ga is that there is no bulk composition change on transformation. According to Massalski,1 the resulting [, phase is a supersaturated extension of the equilibrium [ phase. The lattice parameters continue the trend exhibited

Jan 1, 1965

By J. H. Brophy, J. Wulff, H. W. Hayden

The mickel-activated sintering of tungsten occurs in two stages of densification. A kinetic analysis of the second stage has been based on an appropriate model of the process. As in the first stage, the rate-controlling mechanism for the second stage is also the solution of tungsten in the nickel carrier phase. The transition from the relatively rapid first-stage results from the spherozdization of pores and the initiation of grain growth. Finer grain size due to higher-nickel content leads to more rapid and higher degrees of densification 1 HE sintering of tungsten is accelerated by small additions of nickel, cobalt, and iron.' Experimental evidence in detail has shown that nickel-coated, hydrogen-reduced tungsten powder may be sintered to more than 90 pet of theoretical density at l100o C.2, 3 Simultaneously, a kinetic analysis of the process showed that it took place in two distinct stages. In the first stage, nickel evidently served as a carrier phase through which tungsten atoms could move. This stage was kinetically similar to the "solution-precipitation" step postulated when the carrier phase is a liquid,4 although in the Ni-W case, there is no evidence of the existence of a liquid phase either in equilibrium phase relationships or in microstruc-tures at the temperatures under consideration. It has been shown that this stage corresponds to a process which is rate controlled by a phase boundary reaction.3 More recent evidence has been presented5 showing that after the initial rapid stage of sintering, densification continues in the final stage but at a slower rate, although no mechanism for this stage of densification was defined. An analysis of later stages of densification in solid state sintering has been presented,6 but it is not directly applicable in the present case of activated or carrier phase sintering. It is the purpose of this investigation to study the final stage of nickel activated tungsten sintering in greater detail The effect of varying nickel content has been examined, and a possible kinetic mechanism defined. EXPERIMENTAL PROCEDURE AND RESULTS Commercial hydrogen-reduced tungsten powder from Wah-Chmg Corp., having a nominal particle size of1 µ and a B.E.T. specific surface area of 5500 sq. cm per g was mixed with aqueous solutions of hydrated nickel nitrate in proportions sufficient to produce nominal compositions of 0.25, 1, 3, and 5 wt pet Ni. This solution was then evaporated to dry-ness at approximately 150" C for 15 hr. Following evaporation, the resulting powder cake was broken with a mortar and pestle and reduced in hydrogen at 800oC for 1 hr. Following reduction, the powder

Jan 1, 1962

By D. V. Carter, Dan C. Williams, Franklin M. Hackbusch

During 1939 little of consequence happened in East and East Central Texas in the way of oil discoveries. At the end of the year, there were 47 oil and gas fields in the district. Twelve other fields, 11 oil and one gas, have been abandoned. The ranking fields in order of the number of completions for the year were East Texas, Talco, and Rodessa (Texas portion). There were 511 oil wells (distillate wells included), 32 gas wells, and 257 dry holes completed in the district. Exploration, Discoveries and Extensions During the year, 113 exploratory wells were drilled, the same number as in 1938; four oil fields and one gas-distillate field were discovered. Perhaps the most important discovery, which has been named Barron field, was that of M. Samuel et al., No. 1 Barron in Limestone County. The wells in this field are of the gas-distillate type. Other than the Talco and Sulphur Bluff fields, which produce oil from the Paluxy sand (Upper Trinity), this is the first field on the Corsicana-Mexia fault zone to obtain commercial production from deeper Trinity strata. This "pay" is the Petit lime of the Lower Glen Rose of the Trinity group. The four oil discoveries were: Redland, Angelina County; Bazette, Henderson County; Rowe and Baker, Henderson County; and Marion County Shallow in Marion County. It is believed that the Bazette field, Navarro County, represents an extension of the Flag Lake field. For details concerning discoveries, extensions and important wildcat wells drilled during 1939 see Table 2. Production and Proration The district produced 175,053,729 bbl. of oil (distillate production included) which is a decrease of 4.0 per cent from the 182,369,484 bbl. (distillate production included) produced during 1938. The district's production for the year 1937 was 208,594,453 bbl. The East Texas

Jan 1, 1940

By D. V. Carter, Dan C. Williams, Franklin M. Hackbusch

During 1939 little of consequence happened in East and East Central Texas in the way of oil discoveries. At the end of the year, there were 47 oil and gas fields in the district. Twelve other fields, 11 oil and one gas, have been abandoned. The ranking fields in order of the number of completions for the year were East Texas, Talco, and Rodessa (Texas portion). There were 511 oil wells (distillate wells included), 32 gas wells, and 257 dry holes completed in the district. Exploration, Discoveries and Extensions During the year, 113 exploratory wells were drilled, the same number as in 1938; four oil fields and one gas-distillate field were discovered. Perhaps the most important discovery, which has been named Barron field, was that of M. Samuel et al., No. 1 Barron in Limestone County. The wells in this field are of the gas-distillate type. Other than the Talco and Sulphur Bluff fields, which produce oil from the Paluxy sand (Upper Trinity), this is the first field on the Corsicana-Mexia fault zone to obtain commercial production from deeper Trinity strata. This "pay" is the Petit lime of the Lower Glen Rose of the Trinity group. The four oil discoveries were: Redland, Angelina County; Bazette, Henderson County; Rowe and Baker, Henderson County; and Marion County Shallow in Marion County. It is believed that the Bazette field, Navarro County, represents an extension of the Flag Lake field. For details concerning discoveries, extensions and important wildcat wells drilled during 1939 see Table 2. Production and Proration The district produced 175,053,729 bbl. of oil (distillate production included) which is a decrease of 4.0 per cent from the 182,369,484 bbl. (distillate production included) produced during 1938. The district's production for the year 1937 was 208,594,453 bbl. The East Texas

Jan 1, 1940

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers' vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By J. N. Hummel

The methods of electrical prospecting, which employ contact electrodes to produce an electric field in the ground, furnish information concerning the constitution of the material beneath the surface, as indicated by the distortion of this artificially produced field and anomalies therein. To reveal the distortion of such field of known character, it is only necessary to measure qualitatively the direction of the field, using sensitive compensation methods. In such a case, the survey is relatively simple, and that is an important factor from a practical point of view. The distortion of the normal field thus determined permits an easy interpretation and gives approximate information as to the subsurface conditions, without the necessity of a thorough theoretical knowledge of the electrical field. The true field of application of the equipotential lines and search-coil methods, which are based on this principle of directional determination of the electrical field in the ground, is that of search for deposits of economic minerals for the mining industry, although they can also be used in solution of other problems; for example, in the determination of the strike of anisotropic beds. The distortion of the electric field as represented by the picture of equipotential lines or other measured curves is striking only when bodies having conductivities different from that of the country rock are embedded in the underground, or when the underground is anisotropic. It is obvious that methods based on such a simple principle and capable of solving directly many of the practical problems of mining geology have found a widespread application. However, these methods are unable to furnish any information as to the presence, depth and physical properties of layers in the underground, which have different conductivities, but are parallel, or only slightly inclined, to the surface. Where such conditions exist in the underground, the picture of the field

Jan 1, 1932

By Shozo Saito, P. A. Beck

Mettrllographic and X-ray diffraction study of Cb-Co alloys in the Composition range of 7 to 33 nt. pct Cb, after annealing at 1175 °', showed that near 25 al. pct Cb on MgNi,-lype hexagonal Laves Phaseexists in a narrow composition range, and that an MgCl- type cubic Laves Phase occurs between approximately 27 and 32.6 ut. pd Cb. Lattice parameter and density measures indicated that, in both phases. the deviations from proper Loves sloichimetry result from the substitution of cobalt atoms for some 0f the columbium atoms. Tlle same phases occurant 1000'C, together with an additional phase of unknown structure, which appears between the hexagonal Laves phase and the cobalt-bose terminal solid solutions KOSTER and Schmid' identified a phase corresponding to the composition VCo,, and more recently the crystal structure of this phase has been determined.' In the Ta-Co system Korchynsky and Fountain recently found two intermediate phases at the composition Taco,, one of them metastable. In contrast to the V-Co and the Ta-Co systems, in the Cb-Co system no intermediate phase has been found4 at the composition CbCo,. The present investigation was undertaken in order to reexamine the question of the existence of such a phase. EXPERIMENTAL PROCEDURE Twelve alloys were prepared by arc-melting in a water-cooled copper crucible under helium atmosphere. Electrolytic cobalt and 99.9 pct pure colum-bium powder have been used as starting materials. It was found that melting losses can be reduced by compressing the colunlbium powder in the form of thin pellets before melting. For the alloys used the melting losses were not higher than 1 pct. The intended compositions of all alloys and the chemical analyses of three of them are given in Table I. Specimens from all alloys were annealed in evac- uated fused silica tubes at 1175°C for 3 days and quenched in cold water. A second set of specimens of most alloys was annealed at 1000°C for 7 days and then quenched in cold water. The annealed and quenched specimens were examined metallographically, using the following etchant: 60 pct glycerine +20 pct H,NO, + 10 pct HF + 10 pct water. Powder specimens for X-ray diffraction were prepared by crushing annealed solid specimens in a mortar. Alloys containing 27.3, 28, 29.7, and 32.6 at. pct Cb annealed at either 1175" or 1000°C were very brittle and it was found unnecessary to reanneal the powders. However, alloys containing 24.8 at. pct Cb, or less, especially those annealed at 1000°C, were much less brittle and re-annealing was required to remove the strains present in the crushed powders. In each case reannealing was done at the same temperature at which the corresponding solid specimens were annealed and it, too, was followed by quenching in cold water. In many instances X-ray diffraction patterns were also taken of the polished and etched solid specimens and compared with the corresponding X-ray diffraction patterns obtained with powders. The X-ray diffraction patterns were taken with an asymmetrical focusing camera, using CrK radiation. For precision lattice parameter measurements some X-ray diffraction patterns were taken with a symmetrical focusing camera, again using CrK radiation. EXPERIMENTAL RESULTS A microscopic examination of the alloys annealed at 1175°C revealed that the alloy containing 25.5 at. pct Cb was composed of a single phase, but that the 24.8 at. pct Cb alloy did contain a small amount of a second phase, identified by means of X-ray diffraction as having a fcc structure, undoubtedly the terminal solid solution based on cobalt. Apart from the few very weak lines corresponding to this minor phase, the X-ray diffraction patterns of these alloys could be well interpreted in terms of a MgNi,-type hexagonal Laves phase structure. The indexing of the X-ray diffraction pattern, Table 11, yas based on the lattice parameter values a, = 4.740A and c,

Jan 1, 1961

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By Orville R. Lyons

THE Russellton preparation plant of Republic Steel Corp., located north of Pittsburgh, Pa., prepares 3 1/2x0-in. Thick-Freeport coal by means of a 13-ft 6-in. diam Chance cone and 16 No. 7 Deister tables. The plant feed ranges between 370 and 410 tons per hr, of which approximately 31 pct is ¼x0-in. size, and the plant reject ranges between 14 and 16 pct of the feed. The 3½xY4-in. washed coal, the cone product, is dewatered and desanded by a double-deck Parrish-type shaking screen 46 ft long and 7 ft wide. The 1¼x¼-in. portion is further dewatered by two 4x12-ft single-deck vibrating screens. The ¼x0-in. washed coal from the tables is distributed to three 54x70 in. Bird centrifuges. The dewatered centrifuge product is combined with the product of the de-watering screens prior to loading into railroad cars. During the early part of 1951 complaints were received from officials at Republic's coke ovens concerning the moisture content of Russellton washed coal. The records revealed that during the first half of 1951 the shipped washed coal moisture averaged

Jan 1, 1954

By E. T. Turkdogan, M. L. Pearce

The rates of sulfurization and desulfurization of calcium aluminate, silicate, and ferrite melts by CO + CO2 + SO2 mixtures at 1550°C are reported. It is shown that for melts 10 to 15 mm deep transport of sulfide ions within the melt controls the rate of sulfur transfer. The rate data from shallow melts, i.e., 1 to 4 mm deep, have been analyzed on the basis of a diffusion or a reaction controlled process and indications are that the both processes may play a part in controlling the rate of sulfur reaction. The rates of desulfurization of silicate XVEACTION equilibria between metals, metal oxides, and gases have received considerable attention in recent years. However, the understanding of and aluminate melts increase with increasing PCO2/PCO ratio in the gas stream, the effect being most marked for aluminate melts. The sulfide equilibrium data obtained from the present work are shown to be in accord with the results of previous studies. It is shown that carbon dioxide has a measurable solubility in silicate, aluminate, and ferrite melts. Consideration is given to the partial equilibria which control the directions and the rates of reactions occurring simultaneously in complex heterogeneous systems. the kinetics of heterogeneous reactions, particularly those occurring at elevated temperatures has not been improved appreciably. Almost all the metallurgical reactions occur in heterogeneous systems involving two or more phases. Although in many authoritative text books and original Papers the basic principles concerning the kinetics of heterogeneous reactions are clearly underlined, they are seldom used to the best advantage in kinetic studies, particularly those involving the metallurgical reac-

Jan 1, 1963

By H. S. Wang, Y. P. Gupta

Diffusion of zinc and germanium in liquid silver is measured in the temperature range 975" to 1400°C by use of the capillary-reservoir technique. The ex-perinzental results are discussed in terms of the fluctuation and the "hole" theories of liquid diffusion, assunzing the solute as a point charge equal to the difference in the valences of the solute and solvent atoms. The additional coulombic interaction term due to the excess solute charge is evaluated in terms of the Thomas-Fenni approximation. The theoretical and experimental results agree with both the fluctuation and "hole" theories of liquid diffusion. No perceptible effect on solute diffusion in liquid silver of the size difference between the solute and solvent atoms/ions is apparent. DIFFUSION in liquid silver of electropositive solutes indium, tin, antimony, and homovalent gold has been previously reported by Leak and Swalin1 and Gupta,' respectively. These solutes have nearly the same atomic size but differ principally from one another in excess valence (+2, +3, +4, respectively). The observed differences in the temperature dependence and the rate of solute diffusion were explained in terms of an added coulombic interaction between the solute and the solvent atoms. In the case of diffusion of gold in liquid silver, the data were found to be consistent with an effective valence for gold of -0.85, as proposed by Le Claire.3 Recently, Wang and Gupta4 have reported a study of diffusion of ruthenium, iron, and cobalt in liquid silver. The results of diffusion of these solutes and their temperature dependence were found consistent with the hole theories and the fluctuation theories of liquid diffusion, if ruthenium, iron, and cobalt were diffusing in liquid silver with relative valences -2, -1.3, and -0.5, respectively, instead of -3, -3, and -2 as suggested by the relative position of these elements in the Periodic Table of Elements. Furthermore, the predicted valences for these solutes were observed to be consistent with the sparsely available information on the magnetic properties of some of the dilute alloys of copper and silver with these solutes. In theoretical calculations of solute diffusivity, the solute was assumed as a point excess charge equal to the difference in the valences of the solute and solvent atoms. Both the assumption of a point excess solute charge and the use of the Thomas-Fermi approximation to calculate the potential of a solute charge are less precise for the case of electronegative solutes. Therefore, it was not possible to infer from the data on ruthenium, iron, and cobalt an effect, if any, on solute diffusion of the relative differences in either the Period or the size of the solute and solvent atoms or the solute atoms themselves. A study of the diffusion of Period 4 elements, specifically zinc and germanium was, therefore, undertaken since zinc and germanium, respectively, have relative valences of +1 and +3 in liquid silver and the data obtained on diffusion of these solutes could be compared with the available data on diffusion of Period 5 electropositive solutes, indium, tin, and antimony in liquid silver. From such a comparison, it was hoped to learn something about the effect, if any, of the ion size or the structure of the ion core on impurity diffusion in liquid silver. EXPERIMENT The diffusion of tracer zinc and germanium in liquid silver was studied by the capillary reservoir technique, modified adequately for use at high temperatures. In principle, capillaries containing liquid silver

Jan 1, 1970

By Keith E. Robinson, Brian Stimpson

INTRODUCTION In inclined sedimentary strata slope failure may occur by sliding along bedding and along a discontinuity or weak zone, as illustrated in Fig. 1. This mode of failure may be called 'bi-linear', as the failure surface is comprised of two linear or approximately linear segments. This type of failure has been suggested for the famous Frank Slide, Alberta, Canada (Cruder and Krahn, 1973) in which an estimated 90 M 5 tons (8.97 x 10 MN) of rock separated from Turtle Mountain and buried the town of Frank. Also, with the increasing depth of open pits and the construction of highways through inclined sedimentary strata this mode of failure is of major concern to the rock slope stability engineer. A computer program for calculating factors of safety for this slope failure mode is provided and includes the ability to vary shear strengths of potential slide surfaces, ground water elevations and wedge geometry. LIMITING EQUILIBRIUM MODEL The simple limiting equilibrium model used in the analysis is shown in Fig. 2. It is assumed that jointing is orthogonal to bed- ding and that the interface between the upper and lower wedges there- fore corresponds to a joint plane or planes. No shear strength is attributed to the interface so that the resultant force, P, from the upper wedge acts normally across the interface. The normal loads

Jan 1, 1983

By W. T. Olsen, R. Ulcer

WHEN a liquid alloy freezes, the solid first formed usually differs widely in chemical composition from that last formed, so that there is segregation in the alloy as cast. For example in the copper-nickel system (fig. 1) the first solid formed from a liquid containing 55 atomic pct Cu may contain as little as 38 pct Cu, while the last must contain well over 55 pct. Three factors may act to decrease segregation from the maximum possible. 1. Diffusion in the cooling solid tends to make the phase homogeneous, decreasing segregation. This may be important at slow rates of cooling. 2. Segregation is impossible without diffusion in the liquid. At extremely rapid rates of cooling there may not be enough time to allow maximum segregation. 3. Supercooling delays nucleation to temperatures well below the liquidus thereby decreasing segregation. Hence the first nucleus in the copper-nickel system may contain well over 38 pct Cu. At sufficient supercooling the first nucleus may form below the solidus, in which case there is no reason to expect any segregation whatever. From these considerations, we could predict that at sufficiently low rates of cooling the alloy would be unsegregated because of factor 1 and at sufficiently high rates of cooling there should also be no segregation because of factors 2 and 3. Considerable segregation should occur only at intermediate rates of cooling. We have demonstrated experimentally that segregation can be completely suppressed by rapid rates of cooling. For the alloys studied, however, these rates are too great to be attained in any commercial practice. An alloy of 55 atomic pct Cu, 45 atomic pct Ni was frozen by cooling at varying rates. The degree of segregation in the solid was determined by X-ray diffraction photographs. Slow rates were obtained by slowly cooling the furnace containing the liquid alloy; fast rates by pouring or ejecting droplets of the alloy into water or iced sodium hydroxide solutions. The cooling rate of the droplets can be cal-culated from their dimensions by assuming reason- able values of thermal conductivity.' The experi-ments were repeated with an alloy of 16.5 pct Cu and 83.5 pct Au. A single experiment also showed a 50 atomic pct Bi-Sb alloy had no segregation at the most rapid quench. The position of back-reflection X-ray diffraction lines is a highly sensitive function of the lattice constant, which in turn depends on the chemical composition of the phase. A phase of varying composition will give broad diffraction lines. By measuring the edges of these lines and making suitable corrections for intrinsic line width, it is possible to determine the range of lattice constants represented. These can be converted to chemical compositions from a lattice constant vs. composition curve. Results are shown in table I. In the copper-nickel system the greatest segregation is found at the slowest cooling rates, where the lowest percentage of copper theoretically possible is found. In the copper-gold system, on the other hand, the degree of segregation is decidedly less at the slowest rates of cooling, being greatest at 11,100°C per sec. At no rate is the theoretically lowest percentage of copper (12 pct) found. At the rates of cooling found in sand and die castings the degree of segregation is large and depends little on the rate of cooling. Acknowledgment Most of the material in this paper is abstracted from a thesis presented by William T. Olsen, Jr. in 1948 in partial fulfillment of the requirements for the degree of Master of Science at the University of California.

Jan 1, 1951