Search Documents

By B. R. Coil

One executive writing on capital equipment re- placement stated: "We keep extremely close watch over repair costs and when we reach the point of uneconomical operation, we replace the machine." This, of course, is most elementary, but a very basic premise. However, it seems advisable to set forth several equally obvious principles, so that all discussion will start from the same point. The subject is intended to deal with the point of uneconomical operation due to high operating costs in general and high repair costs in particular. This is not concerned with a similar problem of high costs because of an insufficient number of machines, be they trucks, shovels, or dozers.

Oct 1, 1955

By Robert J. Linney

In the latter part of the year 1943, it was decided to experiment with diamond-drill blast holes in the Old Bed magnetite mine at the Mineville mines of the Republic Steel Corporation, in sections of the ore body where vertical dimensions were large and where development for sublevel bench stopes had already been done. Other possibilities of application for this drilling method were in the reclamation of old floors and pillars in the pitching folds of the Lower Old Bed ore body and in the reclamation of large vertical pillars in the "21" Bonanza-Joker ore body. The cross sections and views of the two ore bodies will show the conditions to which the diamond-drill method has been applied. The Lower Old Bed magnetite ore body is lenticular and dips approximately 30° toward the southwest and strikes generally southeast and northwest. An intensely folded structure, which pitches generally on an axis approximately at right angles to the strike, is continuous from the uppermost old workings down to the present bottom of the mine, and probably continues with depth. On successively lower levels this folded structure becomes greater in vertical dimensions and the two folds are closer together in a horizontal dimension. As shown in Fig. I, this folded structure gives to parts of the ore body considerable vertical dimensions, which provide areas that were developed for sublevel bench stoping above a slushing drift, as shown in Fig. 2. It was in one of these previously devel-oped sublevel bench stopes, No. 26 on the 1185-ft. level, that the diamond-drill blast-hole method was applied for mining the upper sublevel. The lower sublevel was underhand-bench-drilled to the finger raises of the scram drift below. The roof of this stoping area began to break and spall on the lower sublevel, causing the roof to become inclined. Along the hanging wall of the stope this reached an elevation about half way between the two sublevels. A smooth schistose seam in the hanging wall causes the ore to break away freely. Therefore, if bench mining had been carried on in the upper sublevel, a dangerous condition of poorly supported benches would have resulted. When the drillers were slashing across the sublevel te footwall and hanging wall to make a bench, spdlling roof of the opening below would probably have carried away part of the bench, and would have left a dangerous place in which to continue underhand benching. A 6 by 8-ft. raise had been driven between the lower stope and the upper sublevel about 200 ft. from a manway. It was decided to use this raise for a starting cut and to arrange holes as shown in Fig 3, so that a slot would be opened across the ore body between the footwall and hanging wall. This slot would then be used for the purpose of breaking into the ore, by blasting vertical rings of holes drilled at right angles to the axis of the pitching folds as nearly as possible. Layouts of this slot drilling and the rings adjacent are

Jan 1, 1946

By L. Dudley Stamp

On April 1, 1937, Burma, formerly a province of the Indian Empire, was formally separated from India and became an independent unit of the British Commonwealth. In future, therefore, statistics of oil production in India will exclude Burma and those for Burma will be separately published. The last few years have been marked by noteworthy, almost spectacular, developments in the oil fields of Burma and the Punjab. In Burma these developments have been the proving of unexpected extensions of the existing fields and not the discovery of entirely new fields. The new extensions are important not only to Burma in giving a new lease of life to her fields, but also in general as stressing some interesting geological aspects hitherto neglected. Production The production of crude oil in Imperial gallons has been: Burma India 1934 254,760,070 67,265,210 1935 251,338,974 . 71,323,362 1936 265,656,393 69,241,504 1937 (eat.) 270,000,000 70,000,000 The Chindwin Fields.—The small field at Indaw continues to produce steadily about 3,000,000 gal. a year, but no really deep test has yet been successfully carried out and resources are thus not yet fully known. The remote location of the field, inaccessible except by river and situated 22 miles from the Chindwin 270 miles up that river from its junction with the Irrawaddy, has not encouraged active exploitation. The field is worked exclusively by the Indo-Burma Petroleum Co., Ltd. (I.B.P.), using now an automatic gas-lift system, and the company formerly refined the oil at a small refinery at Pantha on the river near by. The chief market was for kerosene in upper Burma. The refinery has now been closed. The oil is stored on the field during the low-water season

Jan 1, 1938

By D. R. Hay, E. Scala

Electrotransport has been superimposed on the rate-limiling- step in zone refining which is the impurity diffusion through the liquid at the solid/liquid interface. The efficiency of zone refining is increased and relative resistivity ratios (P300°k/P4 2°K) he increased by 50 pel in tungsten for a given number of posses using- the electrotransport field-aided method. The effiect of zotze refining in the presence of an electric field on the relative resistivity ratio is examined as a function of its intensity and polarity. THE effect of electrodiffusion on the effective distribution coefficient of zone refining has been discussed by Pfann and Wagner.' Control of the distribution coefficient in zone refining is of twofold interest. A distribution coefficient of unity can be increased or decreased, making possible the transfer of some previously inseparable solutes. The general efficiency of zone refining can also be increased. In the conventional zone-refining process impurities are removed by their retention in the molten zone and subsequent deposition at the end of the rod after a complete passage of the zone. In higher-melting-point systems a second mechanism may also operate, the volatilization of impurities from the molten zone. It has been suggested by schadler2 that, in refractory metals, vacuum distillation plays the predominant role in purification. In Koo's results,3 the resistivity ratio decreased beyond a zone-refined length of 6 in. from the starting end, indicating that some purification does in fact occur by true zone-refining action. Hay and scala4 showed that the degree of purity as measured by the relative resistivity ratio method depends on the square root of time in the molten zone (number of passes) and thus appears to be limited by diffusion in the boundary layer at the solidifying interface assuming good mixing in the body of the molten zone where a linear rate would prevail. The final concentration of impurities in electron-beam floating-zone purification depends very much on the operating conditions and results obtained by various investigators2,3,5 are difficult to correlate. The diameter of the starting material, operating vacuum, and rate of traverse are among the factors to be considered. There are, nevertheless, some general observations to be obtained from the literature. Lawley5 reviewed the literature up to 1962 and concluded that the major contaminants generally remaining in tungsten after electron-beam zone refining are molybdenum and carbon. Molybdenum due to its high melting point and distribution coefficient of nearly unity would be expected to be difficult to remove by either volatilization or zone refining. Carbon is not only a common contaminant in vacuum systems, but is also very difficult to remove by conventional vacuum melting. even with vacuums of 10-7 mm Hg. For each of those impurities removed by zone refining the equation of Pfann and Wagner may be applied: It relates the effective distribution coefficient k to a superimposed driving force which accelerates the solute away from the interface with a terminal velocity L" and to the more conventional zone-refining parameters; v = rate of traverse, t = thickness of the diffusion layer at the solidifying interface, D = diffusivity of the solute in the molten zone, and ko = equilibrium distribution coefficient of the impurity.

Jan 1, 1965

By A. S. Nowick, C. Y. Li

It is deMonstrated that quenching from an elevated temperataupe accelerates the grain boundary relaxation in two solid solutions (aAg-Zn and a Cu-Al). This result is consistent with the proposal that, in solid solutions, grain boundary relaxation occurs by a mechanism of' self diffusion. Nevertheless, an alternative possibilitg, that quenching introduces vacancies into the boundary itself, must also be considered. THE phcnomenon of grain boundary relaxation has been well known for many years,1,2 yet the mechanism of this process is very poorly understood. One of the most interesting suggestions which relates to the mechanism of grain boundary relaxation was that of Ke,3 who claimed that the activation energy for grain boundary relaxation and for lattice self diffusion were essentially the same. The implication is therefore that the elementary step in the two processes is the same. This suggestion is particularly startling in view of the fact that activation energy for self diffusion along a grain boundary is very significantly lower than that for volume self-diffusion. Later evidence5-7 showed that there really are two grain boundary peaks, one which appears in high-purity metals, and the other (which develops at a higher temperature than the first) which appears in solid solutions beginning at solute concentrations in the range of 0.1 pct. Data for silver6 show that Kg's hypothesis is surely incorrect for the grain boundary peak in the high-purity metal, since it has an activation energy of only 22 kcal per mole, but that the hypothesis may still be correct for the grain boundary peak in various silver solid solutions, for which activation energies in the range 40 to 50 kcal per mole are observed. If the elementary step in the grain boundary relaxation process were the same as that for self-diffusion, it would be expected that the relaxation process could be hastened by quenching, 2.c. by introducing a non-equilibrium excess of lattice vacancies. Such a quenching effect has already been demonstrated in the case of another anelastic relaxation process, viz., the Zener relaxation effect. The Zener effect, which occurs in essentially all solid solutions, may be attributed to the reorientation of pairs of solute atoms in the presence of an applied shear stress,' and therefore must take place by means of a volume diffusion mechanism. The hastening of this process through quenching9 has been one way of demonstrating that atom movements in the lattice take place through a defect mechanism, presumably single vacancies. In order to see if the grain boundary relaxation is affected by quenching, it is particularly convenient to compare the grain boundary relaxation with the Zener effect, by choosing a specimen for which both relaxation effects appear. Specifically, a fine-grained sample of a solid solution shows in the curve of internal friction vs temperature, first a peak due to the Zener effect, then a second rise (and eventually a peak at substantially higher temperatures) due to the grain boundary relaxation. The same phenomena are also observable in static anelastic measurements, such as creep at very low stress levels. Thus, for the same fine-grained solid solution, the creepstrain, when plotted against log time, falls on a sigmodial curve with a sharp inflection point, due to the Zener effect, which is followed by a second rise and inflection resulting from the grain boundary relaxation. To look for a quenching effect, static measurements are preferable to the dynamic internal friction measurements, due to the fact that quenching effects tend to anneal out too rapidly at the temperatures at which the internal friction is measured.9 RESULTS AND DISCUSSION Creep experiments in torsion were carried out in an apparatus similar to that described by Ke1, whereby a wire is held under constant torque and its angular displacement is observed as a function of time. The alloy Ag-30 at. pct Znwas selected because of the large Zener relaxation that it displays. The two samples used were a "coarse grained" wire with a mean grain size about twice the diameter of the wire (diam = 0.032 in.), and a "fine-grained" wire which had several grains across the diameter. In Fig. 1 a comparison is made of the creep curves at 160°C of these two samples after they had been cooled slowly from 400°C. Curve A, which represents the coarsegrained sample, shows a unique relaxation process due to the Zener relaxation, with a relaxation time, T , in the vicinity of 100 sec. Curve B, which represents the behavior of the fine-grained sample, on the other hand, shows first the same relaxation process as that in A, followed by a turning up of the curve which corresponds to the onset of a second overlap-

Jan 1, 1962

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By Joseph C. Kieffer

The Duquesne property of the Callahan Zinc-Lead Co. is about 20 miles east of Nogales, in southern Arizona. One mine is near the mill, but most of the mill feed is hauled in by truck from a number of small mines. The same sulphides are found in all the ores, in general, but the amounts vary considerably. All ores contain silver, copper, lead and zinc minerals but one mine ships ore high in silver and lead and low in copper and zinc; while another mine ships ore high in copper and zinc, and low in silver and lead. The common sulphides are galena, carrying most of the silver; chalcopyrite; sphalerite, carrying iron in solid solution; and pyrite, in a gangue consisting of limestone, quartz and garnet. Mineralization is fairly coarse. At the present grind of about 66 per cent minus 200 mesh most of the sulphides are liberated A small amount of chalcopyrite is locked up with the sphalerite and cannot be liberated at an economic grind, and the copper carried into the zinc concentrate with the sphalerite accounts for the comparatively poor recovery of copper in the copper-lead concentrate. Production oF Two Concentrates The milling problem, which was complicated by the extreme variation in the grade of the feed, was first attacked with the idea of producing a silver-copper-lead con- centrate and a zinc concentrate, both with satisfactory grades and recoveries. By February 1941, it was felt that these objectives had been attained, when the grades of the various products and the recoveries were as shown in Table I. A rough outline of the flowsheet and reagents used is as follows: Minus ¾-in. feed to a 7-ft. by 36-in. Hardinge ball mill working in closed circuit with a 36-in. Wemco classifier. The classifier overflow passes to the second cell of an 8-cell bank of No. 18 Special Denver Sub-A flotation machines (volume, 22.5 cu. ft. per cell). A rougher concentrate is removed from the second to the fifth cells inclusive, and returned to the first cell, which is the cleaner. A scavenger concentrate is removed from the sixth, seventh, and eighth cells, and returned to the third cell. Consump-

Jan 1, 1943

By NONE N

Jan 1, 1963

By B. D. Cullity

A distribution of residual stress after plastic elongation is proposed, in which the bulk of the material is strained in compression and a very small portion in tension, This distribution is shown to account both for the X-ray observations and for the effect of plastic straining on magnetic losses in silicon steel. The regions left in compression are tentatively identified with the interiors of the sub-grains revealed by the electron microscope. THIS paper is concerned with the general problem of the nature of the residual stress which is produced in metals by plastic elongation. A particular stress distribution will be suggested which accounts for the main X-ray diffraction observations which have been made. It will also be shown that certain magnetic measurements made on silicon steel can be understood in terms of this stress distribution. X-RAY OBSERVATIONS Uniform straining of a crystal lattice (macro-strain) causes a diffracted X-ray beam to shift its position, and nonuniform straining (microstrain) causes line broadening. If a bar of metal is plastically elongated in the longitudinal x direction and then unloaded, diffracted X-ray lines are observed to be both shifted and broadened.'-= Although the observed line shift indicates the presence of macro-strain, experiments have shown that no macrostrain, in the usual engineering sense of the term, exists.5"7 For example, removal of a layer from one surface of a stretched and unloaded bar does not produce curvature in the remainder of the bar 5'7 Fig. 1 shows the variation of lattice strain in the x direction, as determined from X-ray line shifts, with the applied stress in the same direction. The curve ABC is the normal stress-strain curve of the material, AB being the elastic portion and BC the plastic. In the elastic region AB, the strain measured by X-rays, called the lattice strain, and the strain measured mechanically are both proportional to the applied stress, and both return to zero when the applied stress is removed. Above the elastic limit the lattice strain would be expected to continue to increase along the line BD. Actually, it increases less rapidly with respect to stress, or even decreases, as shown by BE. If the applied stress is then decreased, the lattice strain decreases along EF, which is parallel to AB. As a result, there is a compressive residual lattice strain FA after unloading. STRESS DISTRIBUTION. Since a stretched and unloaded bar does not contain macrostress, it follows that the observed line shift must be due to a special distribution of mi-crostress. Such a distribution is shown in Fig. 2, which shows the variation of the stress u, across a stretched and unloaded bar. The material is assumed to consist of two kinds of regions: regions C, stressed more or less uniformly in compression, comprising the bulk of the volume of the material and responsible for the observed diffrac-

Jan 1, 1963

By F. Weinberg

The distribution of solute during the progressive solidification of dilute Sn-Ag alloys was determined in both solid and liquid as a jbnction of growth rate, rod diameter, temperature gradient, and solute concentration, using radioactive tracer techniques. The results indicated that partial mixing occurs in the liquid during freezing for most of the conditions investigated, approaching complete mixing for larger rod diameters (>2mm) and slow growth rates. Measured solute distributions were fitted to distribution functions based on diffusion controlled solute transport in the liquid state, by treating the normal solute diffusion constant and distribution coefficient as variable solute transport and segregation parameters. Values of these parameters were determined for the growth conditions investigated. Observations were made to determine whether mixing in the liquid was primarily due to volume changes in freezing or to differences in density between solute and solvent. The former effect was investigated using a selected Sn-Bi alloy as a solvent with zero volume change on fusion, and the density effect was studied using vertical solidifications of Sn-In and Sn-Ag alloys, systems having, respectively, very small and large differences in density between solute and solvent. The result indicate that mixing in the liquid cannot be primarily attributed to either volume changes or density differences. THE solute distribution in progressively solidified rods of dilute alloys, in which there is complete mixing in the liquid, is given by the expression1 where C, is the solute concentration in the solid at the point where the fraction g of the material has solidified, C, is the initial solute concentration and k is the equilibrium distribution coefficient. If it is assumed that there is no significant con-vective mixing in the liquid, then the solute distribution in the initial portion of a semi-infinite rod has been calculated to be2 where t is the time from the start of freezing and x1 is the distance in the liquid ahead of the solid-liquid interface at time t. Expressions [1] and [2] describe the limiting cases of solute distribution in the liquid, i.e., complete mixing, or no convective mixing; in practice it might be expected that the solute distribution would be somewhere between these two cases. pfann3 has suggested that Eq. [I] is applicable for partial mixing, as well as complete mixing, if an effective distribution coefficient k1 is used instead satisfactorily describes solute distributions in rods of magnesium, n-g, and b-sb6 alloys that were progressively solidified from the melt without mechanical mixing. The values of kl were observed to depend on the growth rate4-6 and the temperature gradient.6 The purpose of the present investigation was to measure solute distributions in both the solidified rods and the melt as a function of the solidification variables, and to determine to what extent the observed solute distributions could be described by the above theoretical expressions, keeping in mind that expressions [2] and [3] have been derived solely for the case of diffusion controlled solute transport in the liquid and are not theoretically applicable to

Jan 1, 1963

By Pope Yeatman

In my experience, perhaps the most interesting problems came up during the testing, prospecting, developing and equipping of the Chuquicamata and Braden Copper Mines in Chile, and it is proposed in this article to give as briefly as possible what some of those problems were, their solutions, and the decisions made as to the different methods to be employed. The romance of mining is still a great lure to the young man who is making a choice of a profession to follow. The thought of travel to strange and out-of-the-way places, the glamor of pioneer life, the excitement of discovery, the constructive work of building something, entirely "from the grass roots up," or of reconstructing a played-out property and making a success of it-all of these phases have a strong appeal and often influence the young man in the choice of mining as a profession. That great engineer, Col. Seeley Wintersmith Mudd, whom we are endeavoring to honor, while having too much common sense to have been materially influenced by the romance of mining, certainly experienced all of the

Jan 1, 1932

By B. S. Lement

No appreciable stabilization of the austenite-martensite reaction occurs in a 15 pct Cr-0.7 pct C steel unless some martensite is initially present. Stabilization is induced by interrupting the subcool below M,; however, disappearance of the stabilization effect as manifest by burst formation of martensite may occur on continued holding at the final subzero reaction temperature. The higher the temperature of intermediate cycling after the initial subcool, the more permanent is the stabilization effect at the final reaction temperature. Appreciable conditioning of retained austenite occurs on reheating to about 500°C. These phenomena are explainable on the basis of the reaction-path theory. A RECENT investigation' carried out by the authors has shown that isothermal transformation of austenite to martensite definitely takes place in a 15 pct Cr-0.7 pct C steel and that appreciable amounts of martensite can form in this fashion. Investigations2-" arried out on other steels and iron alloys make it seem probable that isothermal formation of martensite is a phenomenon of fairly general occurrence. The reaction-path theory of Cohen, Machlin, and Paranjpe5,7 explains isothermal transformation on the basis of thermal activation of strain embryos which generate martensite plates with a velocity approaching that of sound. On the other hand, the nucleation and growth theory of Fisher, Hollo-mon, and Turnbull8 egards isothermal transformation as due to growth of athermally formed martensite nuclei. The experimental evidence obtained thus far favors the reaction-path theory in that the martensite reaction seems to be nu-cleation-controlled rather than growth-controlled. Stabilization is another phenomenon of importance with respect to the austenite-martensite reaction. According to the reaction-path theory, stabilization is a result of relaxation of strain embryos. It is postulated that strain embryos are present at the austenitizing temperature in the form of dislocations or lattice imperfections in the austenite which vary in the extent to which the lattice is displaced along the strain reaction path leading to martensite. On quenching from the austenitizing temperature, athermal martensite starts to form as soon as the M. is reached, because the activation energy of the transformation which decreases with decreasing temperature is lowered to below the level of the highest energy strain embryos. Martensite plates are generated during the cooling below M, from embryos possessing energies above the activation energy corresponding to the temperature at which the cooling is stopped. The distribution of lower energy embryos is changed because of the elastic and plastic strains produced in the remaining austenite as a result of the transformation. This effectively increases the number of strain embryos at all levels of energy below the activation energy and tends to stimulate further martensite formation either iso-thermally or on subsequent cooling. However, if the temperature at which the cooling is stopped is high enough for relaxation of strain embryos to occur, some degree of stabilization against further transformation may be induced. Whether stabilization will be observed on subsequent cooling will depend on the extent of decrease of activation energy with temperature. If the activation energy decreases sharply with temperature, it is possible that transformation will appear to continue with decrease in temperature in spite of the loss of embryos by relaxation. However, with a more gradual decrease in activation energy, stabilization will be manifest by no further transformation on cooling over a measurable temperature range until the

Jan 1, 1954

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,' McKewan's equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.' On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By Theo B. Comstock

In the summer of 1877, the writer led a party of four young men from Cleveland, Ohio, by way of the Great Lakes, to Prince Arthur's Landing (now Port Arthur), at the northwest corner of Lake Superior, thence, via the Dawson route and side journeys, as far as Cross Lake. It was the original intention to pass down the Pigeon river to its mouth, but the loss of one member of the party for six days in the forest, added to other obstacles, made it necessary to turn back. A well-filled note-book, together with illustrative collections, were sunk beyond recovery at the head of the Maligne rapids by the breaking of a tow-line, and two of our number (including myself) narrowly escaped drowning. I had, probably, obtained information of considerable economic value, but the necessity of travelling nearly 125 miles for provisions (excepting a meagre supply kindly furnished us by a Canadian government gang whom we fortunately met), rendered further note-taking impossible. Until now, such results of this expedition as could be recorded . from memory have gone unpublished, because of my inability to make them serve any useful purpose. The trip of the Institute to Vermilion Lake, only a few miles south and east of our turning point, gives some little excuse for presenting the following lines at this time. The ridge back of Port Arthur, Ontario, which follows approximately the course of the Lake Superior shore line, brings up the slates and accompanying strata through which the silver and gold veins of that region have penetrated. The interior district, hack from the lake, may be briefly described as a glaciated area, having its general drainage less modified by erosion than by the original structure. This statement, however, must be somewhat qualified with reference to minor details, which all bear the unmistakable impress of the ice-flow and its recession. In many respects there is much in this tract to remind one of the Sault Ste. Marie topography, excepting that the granitic character of the rocks is here largely replaced by fissile strata. The Kaministiquia river cuts through several of the parallel folds,

Jan 1, 1888

By J. S. Kirkaldy, D. H. Weichert, G. R. Purdy

Two-phase diffusion couples have been used to simulate the growth of proeutectoid ferrite in ternary Fe-C-Mn austenites. It has been shown, theoretically and expermentally, that the results fall into two classes: a high-super saturation class in which the major role of manganese additions is to influence the boundary conditions for carbon diffusion; and a low-supersaturation class in which the partition of manganese is required. In the latter case, a drastic inhibition of the reaction rate is to be expected. As an aid to the kinetic analysis, a portion of the iron-rich comer of the Fe-C-Mn constitution diagvam has been determined. The conclusions drawn from this work have a direct bearing on the kinetics of the grain boundary ferrite precipitation reaction and thus yield insight into the manner in which alloying elements can influence the rate of austenite-decomposition reactions. THE role of alloying elements in the austenite-decomposition reactions has provoked considerable interest, since it is apparent that an understanding of this phenomenon will yield insight into the harden-ability problem. In the present investigation, attention is focused upon the proeutectoid-ferrite transformation in the system Fe-C-Mn, and upon the manner in which manganese additions affect the growth rate of ferrite. When hypoeutectoid austenite is supersaturated, the ferrite first formed usually exhibits two distinct types of morphology. At low super saturations, grain boundary layers grow into the austenite grains with an approximately planar interface, and usually possess at least one incoherent phase boundary. At high supersaturations, Widmanstiitten plates appear, which bear an orientation relationship' to the parent austenite. In this case, there is a chance of partial lattice matching along the sides of the plates and an attendant semicoherent interface structure. Purdy and Kirkaldy2 have used a two-phase binary Fe-C diffusion couple to demonstrate that carbon volume diffusion controls the incoherent reaction, while Rouze and rube,' using thermionic-emission microscopy, have shown that the thickening of Widmanstatten ferrite plates is appreciably slower than expected for carbon-diffusion control. This suggests that the plates are bounded by partially coherent, low-mobility interfaces. The redistribution of alloying elements during transformation has been the object of studies by Aaronson4 and owmman,5 who have shown that no alloy partition occurs during ferrite precipitation in the systems Fe-C-Cr and Fe-C-Mo, respectively. More recently, Aaronson et al.6 have shown that some manganese partition occurs at low super-saturations in the system Fe-C-Mn, but that no partition occurs at higher super saturations. Pickle-simer et al.7 observed that no manganese partition occurred during the early stages of the pearlite transformation in a manganese steel, and concluded that volume diffusion of the alloying element is not the rate-deter mining factor. The diffusion coefficients pertinent to this investigation have been measured by Wells, Batz, and Mehl8 (carbon in austenite), R. P. smith9 (carbon in ferrite), Wells and Mehl 10 (manganese in austenite), and Kirkaldy and Purdy11 (diffusion of carbon on a manganese gradient in austenite). Kurdjumov 12 has shown that the diffusivity of substitutional elements in ternary austenites up-quenched from martensite may be greatly enhanced, due, apparently, to the presence of a persistent defect structure. The recent work of Krauss 19 showing high densities of tangled dislocations in reversed Fe-Ni martensite is in agreement with this conception. THEORETICAL Diffusion in ternary or higher-order systems may be described with the aid of Onsager's extenbion of Fick's first law,14 in which the flux of each of the n components is assumed to be a linear function of all concentration gradients:

Jan 1, 1964

By P. K. Kaiser, C. Mackay

A circular shaft with a diameter of 6m was excavated by the conventional drilling and blasting method to a depth of 235m through 60m of glacial till, 1 Om of water bearing basal sand, 1 1 Om of clay shale (Bearpaw Formation) and finally a strata of coal, mudstone, siltstone and sandstone (Oldman Formation). The lined shaft was instrumented at three levels by multipoint extensometers to determine the displacement field near the shaft bottom, embedment strain gauges to measure the strains in the liner and IRAD-stress change gauges to observe the radial and tangential stress changes in the rock mass. The data from these gauges were used to determine the in situ stress field. An attempt to measure in situ stresses by overcoring was also made at a higher elevation. The performance of the shaft and its support was then evaluated by use of the "Convergence-Confinement Method". For this purpose the measurements of stress changes and displacements were combined to determine by extrapolation the displacements ahead of the shaft and after the liner installation. The convergence curves calculated in this fashion were then used to evaluate the performance of the cast-in-place concrete liner and of an alternate shotcrete shaft support system.

Jan 1, 1983

By W. B. Nelligam, J. Tittman

Refinements in radiation logging techniques during recent years have involved increasing usage of scintillation ditectors. These detectors produce voltage pulses whose heights are related to the energies of the gamma rays which initiate them. Analysis of the gamma-ray spectrum, as indicated by the pulse heights, yields information about the chemical elements composing the formations surveyed. Refined scintillation counter techniques can furnish chemical information concerning earth formations in situ, from a study of the gamma-ray spectra emitted by the formation either naturally or as a result of neutron bombardment."' Accompanying the rising interest in gamma-ray scintillation spectroscopy, there has been increased activity in the development of accelerator-type neutron sources (in contrast to encapsulated chemical-mixture sources). Such neutron generators are attractive for several reasons: (1) they greatly reduce radiation hazards to personnel; (2) there is a great reduction in contamination danger if they are lost in the hole; (3) they can produce larger neutron intensities than can conveniently available encapsulated sources; and (4) they are capable of being pulsed, thus permitting new techniques in logging. In the past, both accelerator and encapsulated neutron sources have been used by others in conjunction with scintillation-detector pulse-height analysis. The results have not been too encouraging, due to the interference among different gamma-ray spectral lines and to the fact that the gamma-ray peaks were not too clearly distinguishable above the large and ill-defined background "noise".'.' This paper is a status report on laboratory studies of a technique using a borehole accelerator as a neutron source, which gives an improved scintillation spectrum, thus permitting more accurate chemical analyses of the formations penetrated. The Schlumberger-accelerator neutron source' is presented; the origins of inelastic and of thermal-neutron, capture gamma rays are dis- cussed, and results are given for some laboratory measurements performed in borehole geometry. THE NEUTRON GENERATOR-TUBE ACCELERATOR In the attempt to develop an accelerator neutron source which would have the desirable properties outlined in the "Introduction" and which would operate satisfactorily under borehole logging conditions, a small-diameter, cylindrical, neutron generator tube has been developed. This tube utilizes the principle of accelerating deuterons (heavy hydrogen nuclei) by a high voltage so that they bombard a tritium (heavy, heavy hydrogen) target. The resulting reactions produce large numbers of neutrons of 14 Mev energy. Furthermore, the tube is permanently sealed and, thus, the use of pumping techniques in the sonde is avoided. The tube consists of a pressure control, an ion source in which the deuterons are stripped of their electrons, an accelerating gap down which the deuterons are sped by the high voltage, a secondary electron suppressor and a tritium-loaded target. Obviously, the tube requires auxiliary circuitry in a sonde for the control of the ion source, tube pressure, high voltage and other operating variables. Neutron yields, both continuous and pulsed, have been produced under simulated field conditions in the range between 1 and 10 times those conventionally used in neutron logging applications. For the experiments discussed in this paper, neutron-pulse repetition rates in the range between 500 and 5,000 pulses/sec are adequate. Furthermore, by making suitable adjustments in operating conditions, one can vary the pulse width from a minimum of several microseconds up to dc. As will be seen later, the present application to well logging does not require that one have available pulses of neutrons which are appreciably shorter than the time it takes for fast neutrons to slow down to thermal energy in water. As a consequence, much of our interest has been directed towards the operating characteristics of the tube with pulses longer than about 10 microseconds in duration. Our experience to date shows that tubes can be operated in this manner with reasonably constant, average neutron outputs.

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By S. L. Payne, J. P. Morris, R. L. Kipp, G. R. Zellars

The activities of iron and nickel in liquid Fe-Ni alloys were determined by measuring the vapor pressures of iron and nickel above the alloys and comparing with the vapor pressures of the pure metals. Nickel was found to deviate negatively from Raoult's law over the entire composition range. Iron behaves ideally down to 0.7 mole fraction but shows negative deviations at lower concentrations. At 1600°C the activity coefficients at infinite dilution are 0.40 for iron and 0.66 for nickel. 1 HE formulation of the conditions of chemical equilibrium between liquid metals and gases or slags is an important application of thermodynamics to pro- cess metallurgy. Usually the metal and slag phases are solutions of several components; and for accurate calculations, it is often necessary to use the activities of the components in place of their concentrations. Data concerning activities, however, are quite meager. The evaluation of the activities of iron and nickel, presented in this paper, is part of a project to determine activities in iron alloys at elevated temperatures.

Jan 1, 1960

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.' As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972