Search Documents

By F. E. Jaumot, A. Sawatzky

IT as long been recognized that there is a need for accurate systematic data on diffusion in solids. Originally, such data were needed to check existing theories but, more recently, it would appear that it could be used most advantageously as a guide to, or a check for, much needed extensions of the theory of diffusion. The awareness of the conditions which are important to experimental accuracy, the availability of the materials for accurate experiments, and the techniques have improved to the extent that it would now seem to an experimentalist that, unless extensions of the theory are made which take into account the fundamental parameters of the atoms, the electrons, and the lattice in some detail, the field of diffusion will rapidly become an empirical or semi-empirical field. The present series of experiments was designed to provide accurate data on the diffusion of the elements of the IB and IIB subgroups in silver; that is, to provide data on the diffusion in silver of three face-centered-cubic elements with roughly similar chemical properties, but with different atomic or ionic sizes and, similarly, for three noncubic elements. The elements of these two subgroups have different valences, so that the data will not give any significant information on differences due to the crystal structure of the solute. The present paper reports data on the diffusion of copper and mercury in single crystals of silver; the data for the other elements of the IB and IIB subgroups were reported previously by the authors1'2 and by Tomizuka and Slifkin.8 Experiment The general technique used was identical to that previously described1,2 and will not be repeated here. In all cases, the sectioning technique and high specific activity isotopes" were used. The short half-life of Cu64 made decay corrections more important than for the other isotopes, and necessitated around the clock shifts while data were being taken. Each section was counted at least twice (as was true for all longer half-life isotopes) and a monitor was counted along with each sample. Data for the diffusion of mercury in silver are presented at a greater number of temperatures than for the other solutes. This is a result of two circumstances. First, six (of 30) samples had to be discarded because of pitting or recrystallization which occurred during the diffusion runs, even though the samples had sustained high temperature prediffusion anneals. Either of these was a very rare phenomenon in the other experiments, and their occurrence in this case is considered in more detail below. Second, the curves of the logarithm of the activity of the sections vs the square of the penetration deptht were, in general, quite good, but frequently seemed to show one point to have high activity and the next point to have slightly low activity in terms of the best straight line. When this occurred, there was remarkable regularity of the high-low sequence. In any event, the results, as far as diffusion coefficients are concerned, were not affected by this amalgam effect. In fact, the mercury data had the highest internal consistency of any of the data. Results Diffusion of Copper in Silver—-Diffusion runs were made at eight temperatures In the temperature range from 700° to 950°C, for times ranging from 5 to 45 hr. A linear curve of the logarithm or the activity vs the square of the penetration depth was obtained for all samples. Table I summarizes the results for individual samples and Fig. 1 gives a plot 02 the logarithm of the diffusion coefficients as

Jan 1, 1958

By H. Herman, C. Chiou, M. E. Fine

From variation in Young's modulus and Vicker's hardness during GPl zone formation in A1-2 at. pct Cu the following was observed: 1) the presence of grain boundaries does not have any perceptible? effect on the aging reaction; 2) the modulus charge is orientation dependent; 3) the activation energy for zone growth is confirmed to be 11 * 1 kcal per mole; 4) reaging after reversion is preceded by an incubation time that varies with temperature. An analysis is applied to the present data and to data of other workers and kinetic laws dependent on the quenching rate are determined. In Al-base Cu alloys the decomposition product of a supersaturated solid solution at low temperatures (for example 25°C) and the first product at moderate temperatures (for example 150oC) are Guinier-Preston zones of the first kind (GPI).' These zones are nonideal and are thought Jo 'Onsist roughly of sheets of Cu atoms up to 150A in diam and one or two atoms thick.' The kinetics of the reaction, ass — a2

Jan 1, 1961

By S. Weinig, E. S. Machlin

THE mechanism of the martensitic transformation has been the subject of a remarkable number of papers in recent years.' Because the task of evaluating all the available theories is a formidable one, the authors will confine themselves merely to the presentation of results of an experimental investigation of the habit orientation, lattice relations, magnitude and direction of average transformation shear strain, and orientation of subband markings for a single variant of the possible habit systems in an 11 pct Mo-Ti alloy. It is hoped that these data will assist in the establishment of a rigorous theory for the mechanism of the martensitic transformation. Experimental Procedure Specimen Preparation: A sample, approximately 1/2 x 1/4 x 1/4 in., was cut from a double arc-melted ingot composed of commercial-process A titanium and high purity molybdenum (nominally, 11 pct Mo). It was capsuled in evacuated Vycor at 10.-3 mm Hg subsequent to a double argon wash and homogenized for 48 hr at 1100°C. After a direct quench into H2O at room temperature, a large-grained specimen resulted, which, by X-ray diffraction and metallographic means, was subsequently shown to be in the body-centered-cubic phase, ß. Two adjacent, approximately perpendicular faces were polished and the ends of the specimen were ground parallel in a V-block. Fiducial lines were inscribed at 45" to the common edge of the polished surfaces in order that they would be perpendicular to the habit traces of the subsequently formed a plates.2 The specimen was then compressed between the ground ends in a Buehler press to stress induce the transformation ß to a'. Experimental Measurements: The habit-plane orientation, the orientation of subband markings, the orientation relation between the parent ß and the product a', and the transformation strain for the same plate were determined. To further establish the nature of the subbands, one surface was repol-ished and etched. The bands in the a' were still visible and were found to be optically anisotropic under polarized light. Back-reflection Laue patterns were obtained from the ß matrix and from a region comprising both a' plates and adjacent ß matrix (a Cu target was used). By superposition of the two X-ray diffraction patterns, it was possible to obtain a tentative orientation relationship between the two phases. This result was confirmed by a pattern taken after the specimen was rotated to make the basal-plane pole of the hexagonal a' phase strike the film. This necessitated cutting the specimen to expose the a' plate in the new position relative to the X-ray beam. Analysis of Experimental Measurements On the basis of the aforementioned X-ray patterns, the orientation between parent and product

Jan 1, 1955

By E. W. Hough, G. L. Stegemeier

Empirical equations for surface tension of propane and normal butane as functions of reduced temperature are obtained from experimental data. Another correlation relating surface tension to enthalpy of vaporization is given for these two compounds. In addition, new paracbor numbers are calculated for the normal paraffin hydrocarbons. These numbers are utilized for the calculation of interfacial tension of two-component systems as functions of pressure and temperature, using a modified form of Weinaug-Katz equation. The experimental data for two binary systems are approximated by the correlation. From these results it is found that the interfacial tension in the high-pressure region remains extremely low at large pressure decrements below the critical pressure. Thus, it appears that condensate systems may have flow characteristics almost like single-phase conditions even though the pressure is within the two-phase region. Experimental data have shown that interfacial tension divided by density difference approaches zero as the critical pressure is approached. A calculation of wetting-phase saturations indicates that the saturation gradient at the two-phase contact becomes increasingly abrupt as the critical pressure is approached. DISCUSSION Prediction of the surface and interfacial tension of the light hydrocarbons and of two-component hydrocarbon mixtures at various temperatures and pressures may be made if other physical properties are known. Extensive experimental work on single-component and binary systemsl is the basis for the correlations outlined in this paper. Interfacial tension is defined as the specific surface-free energy between two phases of unlike fractional composition, while surface tension is defined as the specific surface-free energy between two phase:; of the same fractional composition. The usual definitions relating interfacial tension to a liquid-liquid interface and surface tension to a gas-liquid interface are not clearly defined when the critical region is included, and there is no sharp distinction between a gas and a liquid phase. Interfacial tension is probably the most important single force that makes one-half to one-third of the total oil actually in place in a reservoir rock unrecoverable by conventional gas-drive or waterflood methods. A rough estimate of this figure for the United States is 100 billion bbl. Interfacial tension presently is used by petroleum engineers in the estimation of saturation gradients at the gas-oil contact and at the oil-water contact. The data in this paper should prove useful for estimates of reserves involving gas-oil contacts. Relative permeability undoubtedly is influenced by interfacial tension, for sufficiently small values. These data should be useful in determining how small the values are In addition, these data should eventually add to our fundamental knowledge of surfaces. At the critical point, all surface excesses approach zero and the thickness becomes very large. SINGLE-COMPONENT SYSTEMS It has been observed1 that the following relationships are good approximations to the physical properties of propane and n-butane.

By H. Hanemann

Discussion of the paper of H. HANEMANN and PAUL D. MERICA, presented at the New York meeting, February, 1916, and printed in Bulletin No. 108, December, 1915, pp. 2371 to 2385. JOHN A. MATHEWS, Syracuse, N. Y.-I should like to ask the authors if there is any evidence of chemical change resulting information of, alpha iron from the gamma crystals found in nickel steel of high nickel content when stressed beyond the elastic limit, similar to the effect produced by drastic cooling. Would the stresses mentioned and the drastic cooling both result in an increase in magnetic induction? I would also like to ask the authors if they have made a test of the hardness. It would be very interesting to see whether the hardness decreased under the conditions of stress, as might be the case if alpha iron were produced. PAUL D. MERICA, Washington, D. C.-While it is impossible to state absolutely, it is my belief that the effect of deformation is approximately the same as, that of -drastic cooling, but we did not make a test, of the hardness.

Jan 5, 1916

By H. W. Kropholler, L. A. Cramer, E. T. Woodburn, J. C. A. Greene

A generalized mathematical structure is proposed whereby internal species mass flows within a flotation network are defined uniquely by a matrix of enhancement factors. An element of the enhancement factor matrix is defined as the ratio of the mass flow of that species leaving a given cell in the concentrate to the species mass flow leaving the same cell in the tailings. To predict the enhancement factors, knowledge of flotation kinetics effects is required. Recently experimental data has become available relating to the performance of industrial flotation circuits which indicate that the discrete or discrete-distributed kinetic schemes are capable of reasonably effective simulations. These simulations show the importance of including froth effects. The prediction of performance of networks from small-scale batch tests on flotation streams shows that the model for the froth phase used in the simulations does not scale-up well and that aeration effects are also difficult to predict. The network analysis should be useful in differential flotation of complex ores and it is disappointing-in this context that little information on the kinetics of activation and depression is available.

Jan 1, 1976

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By R. S. Shoemaker, D. L. Harris

Past investigations into the possibility of concentrating the low-grade iron ores of the Gogebic Range in Wisconsin have been hampered by the complex association of the constituent minerals. In part the problem arises from the fact that the iron occurs essentially as two minerals, hematite and goethite, having nearly the same chemical composition but exhibiting different physical properties. Individual grains of these minerals are usually so small that the ore must be ground to a size finer than 325 mesh if substantial liberation of the minerals is to be secured. Appraisal of beneficiation tests on this iron ore requires, therefore, some method of determining quantitatively the contents of constituent minerals in the various products of the beneficiation. Because of the chemical similarity of the two iron minerals, chemical analyses do not provide a means of differentiation. Although the minerals are different physically, they are both opaque and friable, and as the ore must be ground to a very fine size for liberation to be secured, quantitative microscopic methods of analysis are extremely difficult at best. In an effort to overcome these analytical problems, a quantitative X-ray diffraction analysis method has been developed at the University of Wisconsin for the research program on iron ore beneficiation.

Jan 5, 1955

H. 0. HOFMAN, Boston, Mass (written discussion*).-The paper by Mr.. Pyne gives clear evidence of the difficulties the metallurgist is likely to encounter when he tries to recover in the blast furnace the metal from old chromite lining used as a refractory material in the copper reverberatory furnace. It appears that chromite cannot be fluxed at temperatures which usually prevail in copper blast furnaces. This calls to mind the freezing-point curve drawn by M. Simonis1 of mixtures of chromite and kaolinite. The chromite used in the experiments contained 52.9 per cent. Cr203, 22.6 FeO, 4.8 AI203, 9.6 Si02, .10.1-MgO; FIG. 1. the kaolinite was clay from Zettlitz with 98.5 per cent. clay-substance: The accompanying curve shows that the eutectic mixture with 35 per cent. kaolinite and 65 per cent. chromite freezes at Seger cone No. 15 (1435° C.), while kaolinite fuses at cone No. 35 (1770° C.) and chromite at cone No. 42 (2000° C.). The curve indicates that the difficulty in the blast furnace can be overcome by having at the smelting zone a temperature much higher than is usual in copper smelting; a charge composition similar to that prevailing at the Mansfeld copper smeltery -which gives with 23 per cent. coke a, slag of the composition Si02, .49.09; .(FeMg)0, 5.58; (CaMg)0, 16.02; A1203,-16.02-might flux and fuse chromite.

Jan 3, 1918

By E. C. Simmons

Uranium is an incompatible element with respect to the major rock-forming minerals crystallizing from granitic magma, entering instead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late-stage fluids that can form ore deposits directly, or labile U that can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U-enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite mine area, Washington, have geochemical characteristics that fit the model presented very well. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1984

By R. J. Wagner, F. F. Craig, H. G. Riley, J. D. Griffith

Peripheral water injection has been underway in the Sholem Alechem Fault Block "A" Unit, Stephens County, Okla., since 1955. In the engineering planning of the flood, it was recognized that maintenance of pressure in the large, dry gas caps was vitally necessary to prevent the loss of an estimated 27 million bbl of oil through saturation of the gas caps by the oil banks moving updip on the peripheral flood pattern. The development of an abundant, low-cost water supply and the rising cost of makeup-gas purchases indicated that gas-cap control by water injection was desirable from an economic standpoint, provided an eflective water barrier could be placed without premature water breakthrough into downdip oil producers. A laboratory model scaled to the existing reservoir conditions was comtructed to evaluate the feasibility of gas-cap water injection. Model studies indicated that (I) water injected at the edge of the gar-oil contact would form a continuous barrier between the oil and gas zones, and (2) water would advance uniformly downdip without segregation due to gravity effects provided a specified, minimum water-injection rate was maintained. The model test results also indicated that it was not necessary to fill the gas cap completely with water. Water injection at the edge of one of the gas caps was initiated in March, 1958, to field test gas-cap water injection. Water breakthrough occurred at a downstruc-ture producing well in April, 1959, after approximately 2.5 million bbl of water had been injected into the gas cap. This was the volume calculated to be required to form the barrier between the oil zone and gas cap. This performance indicates that prevention of oil encroachment into dry gas caps in a peripheral water flood by water injection at the gas-oil contact appears practical and that the model studies provided a valid prediction of field performance. INTRODUCTION The Sholem Alechem Fault Block "A" Sims Sand Unit was one of the fist major waterflood projects in Oklahoma to utilize a peripheral injection pattern. Design of control measures to minimize oil encroachment into the large crestal gas caps was one of the greatest single problems during engineering planning of this flood. Engineering studies indicated that saturation of the gas caps with oil displaced by the peripheral water flood could result in a loss of about 27 million bbl of oil, or over one-half the estimated waterflood recovery. This estimate was based on a residual oil saturation after water flooding of 35 per cent pore volume, compared to the negligible oil saturation initially in the gas caps. The Sholem Alechem Springer field, located in Stephens County, Okla., is an elongated anticline with structural dips varying from 400 to 1,000 ft/mile. The structure contains numerous faults, some of which are sealing. The portion of the field considered in this paper is Fault Block "A", which is the largest of the five major fault segments in the field. A map of the unit is shown on Fig. 1. The unit is bounded on the east and west by major sealing faults, on the north by a water-oil contact and to the south by a deterioration of sand development. Two domes, each having gas caps, exist in the unit and are separated by a north-south fault as shown in Fig. 1. The sands being flooded are the Sims sand members of the Springer series of early Pennsylvanian age. The Sims sands average over 100 ft in thickness in Fault Block "A" and have a porosity of approximately 19 per cent. Core permeabilities average 160 md, with interstitial water saturation of about 23 per cent pore volume. Three different zones can be correlated over most of the area. However, they are commingled in most of the producing wells. The two upper zones, designated as First and Second Sims, are the most important. Both the First and Second Sims have gas caps in the east dome, while only the First Sims has a gas cap in the west dome. These gas caps, whose limits are also shown on Fig. 1, initially occupied nearly 11 per cent of the total reservoir volume. The major concern of this paper is the control of the two gas caps in the First Sims sand. Fig. 2 is a cross section, to scale, across the east dome of this formation. Notable features are the relatively shallow dip, the deterioration of the First Sims sand on the south side of the gas cap and the water-oil contact on the northern edge. The formation dip at the gas-oil contact in this cross section is approximately 5".

By D. S. Tomalin, D. F. Stein

The effect of reducing oxygen to low concentrations on the fracture of high-purity iron single crystals has been examined at 78° and 20°K. It is found that iron single crystals grown by the strain-anneal method usually contain a few occluded grain boundaries which may become embittled in the presence of oxygen, thereby nucleating cleavage fractures. High purity with respect to interstitial elements was found to inhibit twinning and evidence is presented for an orientation dependence of the resolved yield stress. Deformation occurred by slip rather than twinning at both temperatures of testing with elongations of as much as 9 pct at 20°K. THE fracture properties of iron single crystals have been observedl-3 to be a function of temperature, orientation, and purity. Allen, Hopkins, and McLennan1 demonstrated that at 78°K iron single crystals became increasingly brittle as the tensile axis approached the (001) pole of the stereographic unit triangle. Iron crystals with the tension axis near a (001) pole were completely brittle and orientations near the (011)-(111) boundary were very ductile, achieving a 100 pct reduction in area prior to fracture. Later work of Biggs and pratt2 and of Edmondson3 demonstrated that by reducing the carbon content of the single crystals the transition between brittle and ductile failure at 78°K could be shifted to orientations nearer the (001) pole. Ed-mondson went further and pointed out that any mechanism which tended to increase the yield strength of the iron (i.e., carbon addition, pre-strain) also increased the tendency for brittle behavior at 78°K. Thus by a reduction of carbon content Biggs and Pratt were able to obtain ductile behavior to within 20 deg of the (001) pole, and Ed-mondson was able to obtain ductile behavior to within 26 deg of the (001) pole. Edmondson's material had a total interstitial content (carbon, oxygen, and nitrogen) of approximately 60 ppm and, although Biggs and Pratt reported no analysis, indications were that their iron contained comparable impurities. Stein, Low, and seybolt4 purified iron single crystals to a total carbon, oxygen, and nitrogen content of approximately 20 ppm. They observed a lowering of the yield stress with this increased purity, and thus one might have expected an observation of increased ductility. Although they tested specimens of orientations which the previous workers had indicated should be ductile, the crystals failed at a 78°K in a brittle manner with little elongation. Stein noted,' however, that about 90 pet of the failures could be traced in origin to occluded grains. Allen et al.1 and Edmondson3 do not report examination of their cleavage surfaces, but Biggs and pratt2 reported that microscopic examination of the cleavage surfaces of many of their specimens revealed the presence of small occluded grains. Honda and cohen6 and Keh7 have also observed the initiation of fracture at occluded grains in iron single crystals. Therefore, the additional complication of occluded grains must be considered in studying the properties of iron single crystals and the origin of fractures determined if the ductility exhibited by the crystals is to be considered meaningful. Various investigators8-12 have studied the effects of impurities on grain boundaries in high-purity polycrystalline iron. Rees and Hopkins10 showed that the addition of oxygen to low-carbon (0.002 pet) iron weakened the grain boundaries, causing a shift from transcrystalline to intercrystalline fracture and a progressive decrease on the brittle-fracture stress with increasing oxygen content. In addition, it has been shown by Low and Feustel11 that the addition of carbon to polycrystalline iron containing oxygen eliminated grain boundary brittleness. Thus, oxygen can embrittle grain boundaries in high-purity polycrystalline iron, but the addition of an appropriate amount of carbon can eliminate the oxygen-induced brittleness. The oxygen content (19 ppm) of the iron "single crystals" employed by Stein el al. was large enough to suspect impurity effects at the occluded grain boundaries. Allen et al.1 Biggs and pratt,2 and Edmondson3 may have masked any occluded grain problem in their specimens considering the relatively high carbon levels they employed. stein13 demonstrated that the addition of as little as 0.9 ppm C to previously purified (less than 5 x 10-3 ppm C) "single crystals" would increase the elongation from a few percent to more than 20 pet at 78°K and the fracture was not associated with grade boundary initiation.

Jan 1, 1965

By Herbert E. Field

The study of the condition and action of carbon in iron and steel is singularly complicated, because one has to consider, also, many contemporaileous reactions foreign to the one under investigation. Great difficulty is experienced in studying iron in the melted state, or during its various treatments in a solid condition, hence such an inquiry must be confined chiefly to a study of the original substance, of the conditions surrounding its treatment, and of the finished product. From a knowledge of these three things, we must form our own conclusions as to what takes place during the transition-period. Inasmuch as it is impossible to determine quantitatively the changes which take place in iron during the various processes of treatment and alteration, we are forced at once into the field of theory for an explanation of many of the phenomena for which we have to account. A recapitulation of the recognized properties of iron and carbon, and of the conditions in which they exist in iron and steel, may be useful as an introduction to the discussion of the subject. Chemically pure iron is soft, malleable and easily welded. It carmot be hardened or tempered, as these terms are understood in relat.ion to steel. In contact with a magnet, it becomes magnetic, but loses this property when the magnet is removed. It is unfitted for castings on account of its lack of fluidity. Those properties of iron which render it valuable as a commercial product must, therefore, be primarily due to foreign substances contained in the iron; and the great variety of these properties is attained by changes in the amount and nature of these impurities, and by the physical treatment of the iron while it contains them. The following properties of carbon make it a prominent factor

Jan 1, 1904

By Thomas Fraser, Alvaro Abreu

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947

By Alvaro Abreu, Thomas Fraser

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947

By G. Beghi, G. Piatti

THE authors examined the problem of the gradual transformation of Al2O3 from the transition phases normally encountered in SAP (r -x-n)1-3 to the stable a phase. This phenomenon is well-known at temperatures above the melting point of aluminum,3"6 whereas in this paper the transformation was studied at temperatures lower than the melting point of the aluminum matrix.

Jan 1, 1967

By J. H. Frye, J. W. Caum, R. M. Treco

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."' It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. Hardness, Lattice Parameter and Ionic Overlap Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2. It is believed that most of the values are accurate within the limits indicated by the rectangles. These data are also presented in Table I. Ultimate Meyer hardness, P u, is defined by the equation: where L = load, D = diametei of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. The question arises as to whether Or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By J. H. Frye, R. M. Treco, J. W. Caum

IT has been suggested that: "Insofar as the hardening due to a solute depends upon the increase of lattice parameter produced by it, it is reasonable to suppose that this hardening might be related to the resistance which the pure solvent would offer to increase in its parameter."' It was further suggested that this hypothesis might be examined by comparing the hardnesses of analogous silver and copper alloys, since the stress necessary to produce a given lattice expansion is quite different in the two metals. Suitable data2,3,4 are now available on these alloys, and we shall proceed to an examination of the hypothesis quoted above. Hardness, Lattice Parameter and Ionic Overlap Increase in ultimate Meyer hardness has been plotted against increase in lattice parameter in Figs. I and 2. It is believed that most of the values are accurate within the limits indicated by the rectangles. These data are also presented in Table I. Ultimate Meyer hardness, P u, is defined by the equation: where L = load, D = diametei of an impression having the same diameter as the testing ball, which in this case is 4 mm. Increase in lattice parameter is defined as the difference between the lattice parameter of the solid solution and that of the pure solvent. The curves in Figs. I and 2 are based on equal solute concentration and an equal degree of plastic deformation pro duced by the testing ball. Hardnesses are corrected to a constant grain size for copper and silver alloys, respectively, and these two grain sizes are approximately equal. Furthermore, all solutes are from the same period of the B subgroup of the periodic table as their solvent. The question arises as to whether Or not lattice parameter is the only factor controlling the hardness of these alloys. There

Jan 1, 1943

By Horace Pops

ThE shape of the primary solid-solubility limits in copper-rich Cu-Si-Zn alloys has been discussed recently1 in terms of the atomic size effects and the electron concentration, e/a. Although these limits are parallel to lines of constant e/a near the Cu-Zn binary system, they deviate and become sharply restricted near the Cu-Si binary system. Hence, it appears that the primary solid solutions with higher silicon contents are restricted by the presence of the intermediate phases, [, X, and p, which follow them in the ternary system. owever, a similar restriction in solid solubility might also result from an interaction in the copper matrix between silicon and zinc. Evidence for such possible interactions has been observed, for example, in the Al-Mg-Si systion.A where a contraction of lattice spacings in the ternary solid solution appears to correspond to an electrochemical interaction between the two solute elements, magnesium and silicon. The observed contraction is associated with restricted solid solubility. It was also shown1 that the extent of the primary solid solubility did not follow the trends predicted by the lattice-distortion oncept." This again suggested that the solubility limits are strongly affected by the stability of the intermediate phases, I, 1, and X . In order to test the above hypotheses, lattice-parameter measurements of the fcc @-phase alloys were determined within the ternary system at a constant electron concentration (e/a = 1.30) and also at a constant zinc content. Alloys of predetermined composition were prepared from high-purity metals and melted and cast under reduced pressures of helium in quartz capsules. Since the weight losses were very slight and did not exceed one part in 2000, the nominal compositions listed in Table I were accepted without chemical analyses. The ingots were homogenized

Jan 1, 1964

By David Baker

Our large modern blast-furnaces, equipped with ore-bins, larries and mechanical means for putting stock into storage, withdrawing it therefrom, and charging it at the tunnel-head, are indeed wonderful in capacity; yet, it is admitted that, with some notable exceptions, they have disappointed us in economy—that is, in the items of low fuel-consumption, uniformity of product, freedom from slips, and reduced cost of repairs and relining. The manager who estimated the cost of pig-iron to be made in a modern plant, by taking the costs of the hand-filled furnace and deducting the amount to be saved by the mechanical appliances, has been surprised, in many cases, to find that unfavorable results in these items of economy have greatly reduced his expected gains. Is there any reason why the fuel-consumption should be greater for a modern furnace than for an older stack using the same mixture ? Certainly the equipment is much more complete, and the trouble, therefore, must lie in the management or in the character of that equipment. Everybody knows that intelligent and vigilant management is a prime requisite: that any neglect of a detail, though it may not be felt that day or week, will surely sooner or later make its appearance as an increased item of cost. But to hold the furnace-maaager responsible for the relatively poor work of the modern blast-furnace would be, I am convinced, a great injustice. For its management has received much more study and care than was given to the older types. Many furnace-managers have lost their health through worrying over this problem, and some hare lost their positions, being held responsible for results made inevitable, as I believe, by the equipment provided for them.

Jan 1, 1905