Search Documents

By Harold Markus, Gerhard Derge

THE first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from I.I2[t] volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. EXPERIMENTAL DATA Cations.-The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.2 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 0 7-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus. ? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1936

By H. A. Schwartz

THE spheroidal form of the temper carbon nodules in malleable cast iron and of the graphite mottles of "mottled" cast iron suggests that in both all the graphite in a given mottle or nodule grew from a single center of crystallization or nucleus.? There is, however, a distinct metallo-graphic difference between the mottle and the nodule; the area of mother metal impoverished in combined carbon by the crystallization of graphite in a mottle is practically coextensive with the ramifications of the graphite, while the impoverished zone of metal corresponding to a given nodule is always larger, and usually much larger, than the approximately spherical mass of graphite crystals forming the nodules. Furthermore, the mottle probably is formed during freezing and the nodule almost always at a considerably lower temperature. Assuming that the nodules or mottles can be used as a measure of the existing nuclei, (capable of germination) we propose to record certain observations as to the graphitizing reaction in the light of the number and habits of growth of these nuclei. The present authors, in cooperation with others1-7, have reported upon various cognate aspects of the problem. The fact that temper carbon is a mass of flakes and not a solid granule has become well recog-nized since the introduction of an improved polishing technique8,9,10 for cast iron. The problem of deriving from the circular planar intercepts

Jan 1, 1935

By Joseph R. Stephens

Deformation substructures of' polycrystalline tungsten, W-2, 9, and 24 pct Re, and W-3 pct Ta were studied by tra?zsrnission electron microscopy. The stress-strain curve for unalloyed tungsten showed gradual yielding followed by work-hardening. Electron nzicrographs indicated a gradual increase in dislocation density with increase in strain up to 5.0 pct. Dislocations, although frequently jogged, were straight over moderate distances and were in a randorn array. Stress-strain curves for alloy specimens of W-2 and 9 pct Re and W-3 pct Ta exhibited a drop in stress at yielding followed by only slight work-hardening. Electron micrographs of these specimens after strains of 0.05, 0.1, and 0.5 pct revealed no change in dislocation substructure from the unstrained specimens. After 2.0 pct strain, the three alloys exhibited dense networks. W-3 pct Ta was characterized by straight, frequently jogged dislocations comparable with the dislocation structure in unalloyed tungsten after a similar amount of strain. In contrast, W-2 pct Re exhibited dislocations that contained widely spaced jogs, while W-9 pct Re had developed a cell structure after the relatively srnall strain of 2.0 pct. The W-24 pct Re alloy contained a few dislocations after 0.1 pct strain, while after 0.5 pct strain twins were evident. Dislocation slip bands apparently preceded the twins. The stress-strain curve for the alloy indicated that twinning commenced after approximately 0.25 pet strain. These results indicate that the primary effect of low rhenium concentrations (2 and 9 pct) in tungsten is to increase dislocation multiplication after macroyielding by reducing the Peierls-Nabarro force (lattice resistance to dislocation motion). The dislocation bands that precede twins in W-24 pct Re may be caused by localized internal stresses resulting fro a metastable structure, for example, clustering of rhenium atoms. The effect of high rhenium additions (22 a 65 pet* Rproperties of tungsten. Klopp, Witzke, and Raffo5 reported bend transition temperatures as low as -100°F (200°K) for dilute electron-beam-melted W-Re alloys tested in the worked condition. Recrystalliza-tion increased the bend transition temperature, but alloys with 2 to 4 pct Re were still markedly superior to unalloyed tungsten. Fractographic examinations of tungsten and W- 3 pct Re and W- 5 pct Re alloys by Gilbert 6 revealed that these low rhenium alloys showed a greater tendency toward cleavage failure than did tungsten. Garfinkle 7 showed that rhenium additions, up to 9 pct, to (100) oriented tungsten single crystals increased the proportional limit stress and decreased the flow stress and the rate of work-hardening. In addition, while deformation in unalloyed (100) oriented crystals apparently involved both (110)100) and (112) slip, crystals with rhenium contents of 5 andpct or more deformed primarily by (112) slip. The mechanism by which high and low rhenium additions affect the mechanical properties of tungsten is still not well-established. The present investigation was undertaken to determine by transmission electron microscopy the effects of low rhenium additions, 2 and 9 pct, and a high rhenium addition, 24 pct, on dislocation substructure in the early stages of deformation of polycrystalline electron-beam-melted tungsten. Unalloyed tungsten and a W- 3 pct Ta alloy were included for comparison. EXPERIMENTAL PROCEDURES Materials. Triple electron-beam-melted tungsten, W-2, 9, and 24 pct Re, and W- pet Ta were used for this investigation. Chemical analyses of the cast ingots are given in Table I. A description of the starting metal powders and melting and fabrication pro-cedures for unalloyed tungsten and the W-Re alloys is reported.5 The W-3 pet Ta alloy was processed in a similar manner. Compression specimens measuring 0.300 in. (7.6 mm) in length by 0.130 in. (3.3 mm) in diam were machined from swaged rods. All alloy specimens were annealed in a vacuum of 8 x 10- 6 Torr (10'2iVper sq m) for 1 hr at 3600°F (2255°K). The recrystallized grain size ranged from 0.06 to 0.08 mm diam for the alloy specimens. Unalloyed tungsten was annealed at 2400° F (1589°K) for 1 hr to produce a recrystallized grain diameter of approximately 0.12 mm. Specimens were electropolished in a 2 pet NaOH solution to a diameter of 0.125 in. (3.18 mm) to remove surface notches resulting from grinding and to improve reproducibility of t data. The ends o the compression specimens were ground flat, parallel to each other, and perpendicular to the longitudinal axes with 4/0 emery paper. Compression Tests. The compressive stress-strain apparatus used for compression tests is described in detail by Stearns and Gotsky.9 Room-temperature compression tests were conducted at a crosshead speed of 0.01 in. per min (0.25 mm per min).

Jan 1, 1969

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By John Johnston

When I was honored by being invited to give the Howe Memorial Lecture, I decided to read Howe's book, "The Metallography of Steel and Cast Iron," published in I9I6—that is, about 25 years ago—in search of a text. I found the book written in fine, clear, attractive, yet precise style, as I expected, knowing that his father— Dr. Samuel Gridley Howe, his mother— Julia Ward Howe, and all of his four brothers and sisters had lived in a New England literary atmosphere and had written books. This leads me to suggest that many authors of metallurgical papers and books could well study Howe's writings with a view to the improvement of their own. I failed to find a specific text, but did find a subject, for in reading his book I was struck by the few instances in which time is considered explicitly as a factor in the phenomena examined, and by the fact that many of the hottest arguments would have been settled had time been taken properly into account. Indeed, Howe hardly mentions time except in a rather incidental way, as in a few references to lag; for instance: The lowering of temperature at which the transformation occurs by rapid cooling . . . is a phenomenon of undercooling or lag. It is in part explained by the fact that the transformation itself is a time-consuming reaction which, setting in during a rapid fall of temperature, is naturally protracted till the temperature has sunk far below that at which it is due. He does discuss, quite fully, the iron-clrbon equilibrium diagram, as known at that time, introducing it by stating: As he is a reasonable man who is not deterred from using a hand truck for moving his trunk by the consideration that he has thus to move a trunk plus a truck, so am I reasonable in putting into your hands this useful, indeed indispensable. tool for mastering the ABC of iron metallurgy. Somewhat later, in introducing a discussion of the phase rule, which "it would be hardly proper to pass ... by without an attempt to outline its meaning," for "a clear exposition of its applicability or jurisdiction is needed to restrain the half-initiated from misusing it and the uninitiated from being misled by these misuses," he writes—and I quote his statement because we cannot properly discuss the influence of time on a process until we know the state of equilibrium which would ultimately be reached by the system under consideration: It is a most remarkable and valuable generalization, its conceptions help greatly toward getting a broad outlook on metallography, but its misconception has brought out a flood of obscuring writings. it tells us about the constitution towards which alloys tend, that which they reach when equilibrium is complete, when all tendencies have corrected themselves and have been complied with completely. Its application, in absence of true equilibrium, is like determining density with a telescope or even with a tuning fork; it is like the mad tea party at which the butter put into the works of the watch was the best butter. If the reader learns no more than to beware of attempts to dccipher the conditions of inequilibrium by a law which touches only the conditions of exact

Jan 1, 1942

By E. W. Stewart, G. P. Conard, J. F. Libsch

The effects of several additives upon the reduction characteristics of hydrogen-reduced ferrous formate are described. The various additives inhibit sintering of the reduced iron particles by apparently different mechanisms. The magnetic properties of the low density compacts produced from the resulting ultra-fine iron powders were improved markedly. THE permanent magnetic characteristics of ultra-fine iron powder prepared by various means have been a subject of considerable interest and experimentation in the past few years. When such particles are small enough to show single domain behavior, they possess' 1—permanent saturation magnetization, and 2—high coercive force. In the absence of domain boundaries, the only magnetization changes in a particle occur through spin rotation which is opposed by relatively large anisotropy forces. With decreasing particle size, the coercive force tends to increase to a maximum and then decrease because of the instability in magnetization associated with thermal fluctuations. Kittel' has calculated the critical diameter at which a spherical particle of iron can no longer sustain domain boundaries or walls to be approximately 1.5x10-' cm. Stoner and Wohlfarthr in England and Neel4,6 in France have shown from purely theoretical calculations that the high coercive force expected from single domain particles is dependent upon crystal anisotropy, shape anisotropy, or strain anisotropy contributions. Further work by Weil, Bertaut,' and many others has contributed much to the understanding of fine particle theory. Neel and Meikeljohn" have demonstrated that a decrease in particle size below a critical value of approximately 160A leads to a quite rapid decrease in coercive force because of the prevention of stable magnetization by thermal agitation. Lih1, working with powders prepared by the reduction of formate and oxalate salts of iron, has shown the marked influence of powder purity upon magnetic properties. Maximum coercive force was obtained in powders of approximately 65 pct metallic iron content while the maximum energy product, (BxH) occurred in powders of 85 pct metallic iron content. Careful consideration of the preceding theoretical considerations and experimental results has led to the manufacture of permanent magnets from ultra-fine ferromagnetic powders by powder metallurgy techniques. Such work has been done by Dean and Davis," the Ugine Co. of France, and Kopelman." The aforementioned work of Kopelman and the Ugine Co. was concerned somewhat with the effect of various additives upon the properties of hydrogen-reduced ferrous formate. Virtually no work, however, has been published on the effects of additives on the reduction rates of metal formates, although unpublished work by Ananthanarayanan16 howed promise of improved energy product in ultra-fine iron compacts prepared by the hydrogen reduction of a coprecipitated mixture of magnesium and ferrous formate. After consideration of the preceding information, it was hoped that a better balance between the metallic iron content and particle size of the reduced iron powder could be accomplished by a prevention of the attendant sintering of the partially reduced iron powder during the reduction reaction. It appeared possible that magnesium oxide might interpose a mechanical barrier between adjacent iron particles and prevent their sintering together, while metallic cadmium and metallic tin would interpose a liquid barrier which might accomplish the same purpose. The degree to which these materials were effective in accomplishing the foregoing objective and the experimental details associated with the work are reported in the following sections of this paper. Experimental Procedure Preparation of Formate and Oxide Mixtures: To obtain ferrous formate of reproducible reduction characteristics, a slight modification' was made in the technique of Fraioli and Rhoda." A supersaturated solution of ferrous formate was mixed with an equal volume of 95 pct ethyl alcohol and the formate crystals precipitated by stirring and screened to —325 mesh. These crystals were in the shape of elongated hexagons, approximately 4x10 micron in dimension. Various preparations of such ferrous formate, designated as lot 111, were reduced for 2 hr, yielding ultra-fine iron particles of exceedingly reproducible size, metallic iron content, and magnetic properties. The magnesium and cadmium formates were prepared by the reaction of dilute formic acid with their respective carbonates, while the tin formate was prepared by the reaction of dilute formic acid with stannous hydroxide. To evaluate the effect of metallic formate additives in intimate mixture with the ferrous formate, varying amounts of magnesium, cadmium, and tin formates were coprecipitated with the latter. The designations of these materials and their chemical compositions are given in Table I. Due to the differing solubilities of the various formates in aqueous media,

Jan 1, 1956

By M. C. Cheney

The active development of the vast East Texas oil field, the attendant effects of the rapidly increasing flow from its prolific wells and the efforts to bring order out of chaos precluded or dwarfed other oil development in Texas during 1931. In a paper by Dr. F. H. Lahee1 presented at the October, 1931, meeting, the early history of the East Texas oil field is described and the sequence of events in connection with its development and efforts to control its production up to Sept. 25 is narrated. At that time the Railroad Commission of the state reduced the production of the field to a maximum of 400,000 bbl. per day by restricting the allowable daily production per well to 185 bbl. By further reduction in the daily production per well to 100 bbl., the field was held below that maximum figure during the remainder of the year. Meanwhile, as a result of an injunction against the Railroad Commission, its authority in the field was superseded on Oct. 13 by the Governor of the state, and after that date production was controlled directly by his orders issued under authority of martial law. Suits to contest this authority were brought in the Federal courts and were pending at the close of the year. On March 5, 1931, as a result of the East Texas production, posted prices for Mid-Continent 40' A.P.I. crude slumped from $1.07 to $0.67. As East Texas production continued to mount, posted prices in East Texas were reduced to $0.37 on June 3 and $0.22 on July 8, although in that field most of the oil was sold for much less, bringing the producer and royalty owner as low as $0.025 per barrel. Northeast Texas To the information contained in Dr. Lahee's paper, it can now be added that the East Texas field has produced over 105,000,000 bbl. and registered about 3700 successful completions during 1931. There may be some merit to the recent prediction that a large part of the field will have passed its flowing period by the middle of 1932 unless

Jan 1, 1932

By W. A. Wood, W. H. Reimann

A study is made of the creep that can be induced in armco iron at room temperature by superposing small amplitudes of alternating torsion on a tensile creep load. It is shown that the creep differs from that in comparable tests on copper in being trmsient only. At the same time, though transient, the creep can produce extensions of some 10 pct under creep loads less than the tensile yield stress of the material. The creep can be largely suppressed b$ applying cyclic strain of suitable amplitude before applying the creep load and the metal thereby stabilized. At room temperature, plastic flow in a metal under steady load is normally limited by strain-hardening processes. However, if a small cyclic stress is superposed on the steady load these processes may be more or less neutralized and, as shown in recent investigations,'-4 plastic flow may continue. In this way annealed copper, for example, can be induced to creep continuously to fracture under loads as small as 1 tsi. Dislocation mechanisms possibly responsible for this room-temperature creep have been usefully reviewed by Feltner.But discussion so far has been based mainly on creep as it is found in close-packed metals initially in the annealed state, and their behavior may not be general. In fact, recent work shows that the form of creep in annealed copper is different from that even in cold-worked copper;7 the creep thus depends on the dislocation pattern already in a metal as well as on the metal itself. This paper describes the creep in annealed armco iron, tested in the same way as the above-mentioned copper. One object was to see how creep in a typical bcc metal compared with that in the annealed close-packed metals. Another object was to utilize the fact that a bcc metal like iron has a more pronounced elastic range than close-packed metals like copper and to find to what extent the creep load or superposed cyclic stress had to exceed their re-

Jan 1, 1964

By C. G. Dunn, E. F. Koch, K. T. Aust

Strain-induced grain boundary migration was studied in a series of silicon-iron (3% pct Si) bicrystals of controlled orientations. Each bicrystal was given a 7 pct cold-rolling strain rind annealed at 1100°C. The direction of boundary migration was found to depend on orientation; results for several orientations related by a common [110] axis are given. Analysis of the micrographic and X-ray data is made in terms of the residual strain-energy densities within the crystals (energy per unit volurne) and a driving force on the boundary due to an energy density difference across the boundary. Relative strain energies were obtained for the various orientations investigated. A CHROME-acetic acid electroetching method for revealing dislocation sites in silicon iron was previously applied to clarify the structural features and the energetics involved in strain-induced grain boundary migration.',' The present paper is a continuation of this study, but is primarily concerned with the influence of crystal orientation. Sperry, as reported by Beck,3 attempted to determine the factors that influence the preferred growth of one grain over another in aluminum due to strain-induced boundary migration. He found that the particular grain of a pair which work hardened more was invaded, although exceptions to this correlation were noted. The index of work hardening was determined from microhardness measurements of each grain before and after cold-rolling. In the present study, orientation itself was taken as a useful variable for studying the behavior of individual grains in a bicrystal and the direction of boundary migration, since the extent of work hardening is orientation dePendent." The effect of strain on boundary migration is evident from a consideration of driving forces. Thus, in the absence of inclusions, the driving force (per unit area of boundary) for growth of grain A into grain B when a bicrystal is strained and annealed may be expressed as follows:2

Jan 1, 1960

By H. R. Shidel

This paper summarizes the results obtained from the preliminary cementing of wells in an effort to cut off the bottom water. The object of this work was two-fold: (1) To prevent the oil sand from becoming flooded. (2) To plug off bottom water, thereby preserving the individual well and reclaiming production. Valuable suggestions and help have been given by the following named: Messrs. Kyle and La Velle, of the U. 8. Bureau of Mines; Magnolia Petroleum -Co.; Freed Oil and Gas Co. The cementing work was carried out under the personal supervision of L. J. Snyder. In an unpublished paper on the "Water Problem in the Augusta Field," 5. K. Clark reaches the following conclusions: (1) That the great amount of water present is bottom water, occurring in the Varner sand, the main producing or the 2500-ft. horizon, (2) That the only striking connection between structure and water is in .the area of the marked fault on the Ralston, E. C. Varner, and F. Varner leases in sections 8, 9, 16 and 17. (3) That the oil occurs in porous streaks, generally separated by finegrained, well cemented sand, which is barren. Possibly two or three such pay streaks may be found. That under a pay, fine-grained sand occurs, which is presumably barren at the time of drilling, but soon reveals water. The writer takes partial exception to the last point, because well defined shale, slate, lime, or hard sand breaks have been encountered in a great many cases, separating the pay streaks under which water is often found. This is not an invariable occurrence, as cases have been noted when the oil has been followed immediately by water in the same stratum. In an effort to overcome the water menace, the following methods of plugging were tried: (1) Plugging with wood, lead, and limit plugs. (2) Plugging with sand pumpings.

Jan 1, 1920

By R. H. McLean

Velocity, kinetic energy and shear in crossflow beneath three-cone jet bits may influence cleaning of the bottom of the borehole and the teeth of the bit. Laboratory investigation shows that each of these parameters is a function of the diameter of the borehole and the product of the volume rate of flow and velocity through the nozzles (QVn). Increasing QV, or decreasing the diameter of the borehole increases each parameter. These functions provide means of predicting the magnitude of each parameter and of scaling the cleaning forces. INTRODUCTION In drilling operations using conventional jet-type rock bits, the impinging jels create an important flow mechanism. Called crossflow, this flow mechanism originates in the impact area of the jets, spreads across the bottom of the hole and supplies the principal source of energy to clean the teeth of the bit and most of the bottom.' Besides providing the means of cleaning cuttings from the bit and the hole bottom, crossflow may also have other, less direct, effects on the rate of penetration. The shear stress generated on the bottom by crossflow will inIluence the thickness and permeability of any filter cake of mud solids or crushed material which forms on the bottom.' These factors may affect the rate of penetration. A previous pulblication introduced some fundamental concepts of crossflow.' Crossllow was shown to occur in a thin layer adjacent to the bottom, and to cover the bottom completely. The maximum velocity in the crossflow above any position on the bottom was found to be directly proporlional to the square root of the product of the volume rate of flow and velocity through the nozzles—the jct QV,,—and inversely proportional to the diameter of the borehole. This information indicated that the effectiveness of crossllow in scavenging the bottom can be improved by maximizing the jet QV. The investigation reported herein amplifies the definition of crossflow. Complete velocity profile data above a representative position on the bottom are analyzed. These data better illustrate control of the capacity of crossflow to scavenge the bottom, and also relate shear stress on the bottom to known, controllable parameters. The conclusion reached in the previous publication that maximization of the jet QV. produces the maximunl cleaning beneath current jet bits is unchanged by these new data; rather, it is strcngthened. Data presented here show that the kinetic energy flux above a representative position on the bottom is maximized by maximizing the jet QV. The shear stress on the bottom will also be shown to be maximized in the same manner. Since the functions relating the jet QV. to velocity, shear stress and kinetic energy also involve the diameter of the borehole, means of equating, or scaling, these quantities in different sizes of boreholes will be illustrated. EXPERIMENTAL EQUIPMENT AND TECHNIQUE JET BIT MODEL Data were recorded from the same laboratory model as used in the aforementioned investigation of the flow around a jet bit.' The model consisted of a 43/4-in. three-cone, jet-type rock bit in a smooth, flat-bottomed borehole constructed of lucite. The bit had a shape and nozzle placement closely resembling larger three-cone jet bits commonly used in field operations. Fig. 1 illustrates the impact area on the bottom of a jet from this bit. Details of the orientation of the jets may be found in the previous publication. TECHNIOU'E OF MEASUREMENT Measurements of the crossflow were made by inserting a very small Pitot tube through the bottom of the simulatetl boreholc. Extreme thinness of the layer of crossflow necessitated accurate measurements of the height of the Pitot tube above the bottom to achieve close definition of the velocity profile. A cathetometer, which could be read to the nearest 0.005 cm, was used to make this measurement.

Jan 1, 1966

By D. J. Hawthorn

The widespread interest shown during the past year in the study of subsurface pressures warrants brief reference to its early development. Though it is impossible to set an exact date when constructive thinking on the subject first began, nevertheless, evidence is available that thought was given to the problem as far back as 16 or 1.7 years ago. There is record in one of the foreign journals of actual subsurface tests made by crude methods in one of the Rumanian fields in 1918 and 1919.' These tests were performed in conjunction with studies made on wells produced by bailing and, incidentally, the final outcome of the work led to the development of the so-called "duplex bailer" which is reputed to have trebled volumetric bailing efficiency. From this time on to 1927 a few scattered bottom-hole pressure determinations were made with makeshift instruments of one form or another, but probably not until 1927 was any great amount of concerted effort directed to the subject. At this fall meeting of the Petroleum Division four years ago was presented one of the first papers2 to appear in this country written for the express intent of advocating the value and importance of subsurface pressure determinations. It is thought to have been the first to present direct data on subsurface pressures obtained through the use of a specially designed recording instrument. As might be expected, the instrument had its limitations, but reasonably accurate results were obtained and, to say the least, it constituted a progressive step in the right direction. During the period from 1927 to 1931, many noteworthy improvements were made in the design and perfection of subsurface pressure instruments suitable to meet all conditions. Because of the magnitude of this task much credit is due the men who pioneered this work. They should feel a keen sense of satisfaction in the thought that their efforts have paved the way for the continuation of this most valuable study. At the present time more than a dozen companies are operating subsurface pressure instruments in the Mid-Continent field. Engineers in

Jan 1, 1933

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By H. Biloni, G. F. Bolling

The microsegregation in tin specimens containing 0.2, 0.5. or 1 wt pct Pb has been studied m detail. The specimens were grown from the melt in a controlled fashion and exhibited a well-developed cellular substructure. In general, a severe microsegre-gation can be observed in all the photomicrographs presented. Some observations of special interest are: the distribution of a second phase, the presence of a eutectic in several forms, the evidence for dif- THE Smialowski or cellular substructure which forms during solidification has been extensively studied during the past decade.'* Many of the im- *Most references to the cellular substructure except for the last 2 years are reviewed by Winegard.' portant characteristics of this substructure, such as its occurrence and variability with growth conditions, its association with the phenomenon of constitutional supercooling, and its effect on dislocation production and mobility, have received quantitative fusion of solute in the solid, and the enhancement of segregation at a dislocation subboundary network ("striations"). On the basis of the metallographic observations, it can be deduced that the segregation observed is representative of the solute segregation produced during crystal growth. Some deductions are also made about the interplay of the two substructures, cells and striations, and about the mode of cellular growth. investigation both experimentally and theoretically. However, the concentration profile of the solute segregated during crystal growth has not been examined in detail. Tin crystals grown from melts containing various concentrations of lead have been most extensively studied. In a recent investigation of Sn-Pb alloys, Kramer et a1.2 were able to measure the effective solute distribution coefficient, k,, at the most advanced points of the solid-liquid interface, over a large range of growth conditions, finding it to approach the value of k,, the equilibrium distribution coefficient. As will be shown, this must lead to drastic segregation. Another recent study of several Sn-Pb alloys was made by Plaskett and winegard3 who investigated the variation of growth conditions

Jan 1, 1963

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.'-' One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

By J. E. Dreier

The Pachuca - Real del Monte district has produced about 46.6 kt (51,300 ton) Ag from subvolcanic vein deposits. Three types of wall rock alteration are spatially related to the veins: K-feldspar, propylitic, and phyllic. K-feldspar alteration occurs within veins; propylitic alteration occurs in fractured rocks between veins; and phyllic alteration occurs above veins. Concentrations of some trace elements in altered rocks relative to unaltered rocks are summarized below. [ ]

Jan 1, 1983

By L. W. Kempf

DURING the recent development of aluminum alloys for free-cutting screw-machine rod, it became desirable to know something of the solubility of lead and bismuth in liquid aluminum and in some aluminum alloys. The literature is not particularly helpful in supplying this information. These portions, therefore, of the constitutional relationships of aluminum-ismuth and aluminum-lead alloys were investigated by thermal analysis and by chemical analysis of samples taken from aluminum-rich melts in equilibrium with precipitated lead or bismuth. The solubility of lead and bismuth in some liquid aluminum-copper alloys was also investi-gated. Some consideration was also given to the solubility of these elements in solid aluminum. Among the earliest investigators of the aluminum-lead and aluminum-bismuth systems was Wright,1 who reported that melts of aluminum and lead formed two layers indicating limited liquid solubility. Under his conditions, the aluminum-rich layer was reported to contain 1.91 per cent Pb and the lead-rich layer, 0.07 per cent Al. Subsequently, Pecheau2 found that in aluminum-rich alloy melts with more than 10 per cent Pb three layers were distinguishable. He reported that the middle layer contained from 3 to 10 per cent Pb. He also found that the melting point of aluminum appeared to be lowered slightly by the addition of lead. Gwyer3 investigated these alloys and found evidence of a slight lowering of the freezing point of aluminum by the addition of either lead or bismuth. He found no evidence of solid solubility in either case and made no attempt to determine the liquidus curves. Hansen and Blumen-thal4 reported that the addition of lead distinctly lowered the solidifica-tion point of aluminum. They also found that bismuth lowered the melting point of aluminum. Guillet5 reported almost complete mutual immiscibility for the aluminum-bismuth alloys in the liquid state. Bohner6 examined the effect of various concentrations of lead and bis-muth on the electrical conductivity of aluminum. He found decreases in conductivity on annealing at 500° C. as compared with the conductivity of the same alloys on annealing at 300° C.

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938

By Francisco Cadena

The construction of Norris Dam, built by the Tennessee Valley Authority on the Clinch River, a tributary of the Tennessee River, involved the production of coarse and fine aggregate for approximately 1,000,000 cu. yd. of concrete. A hammer-mill plant for the manufacture of sand from quarried rock was indicated as the most economical method of providing this material. The abrasive character of the feed as compared to the average hammer-mill feed made it necessary to control operations rather closely, and this resulted in the accumulation of many data hearing on production and maintenance. This paper will deal only with three specific sets of data, accompanied by such general information as may be necessary to explain the conditions under which they were obtained and followed by discussions on the relation of silica content to hammer wear, comparative costs of slugger and stirrup hammers, and comparative costs of tool-steel and manganese-steel grate bars. Coarse Aggregate Aggregate for the concrete poured at Norris Dam came from a dolomite quarry within 2000 ft. of the west abutment of the dam. Geologically this rock is known as a Knox dolomite. A typical chemical analysis is given in Table 1. Table 1.—Typical Chemical Analysis Per Cent H2O, 110° F............................................. 0.02 lgnition loss.............................................. 43.56 MgO.................................................... 19.19 CaO ................................................... 29.07 Fe²O³.................................................... 0.39 Al2O³ .................................................. 1.94 SiO2..................................................... 5.75 SO2...................................................... Tr. Rock was carried by 12-yd, dump trucks to a 42-in. gyratory crusher set at 6 1/2in. The product of the primary crusher was taken by a belt conveyor to a double.-deck vibrating screen followed by a 5 1/2-ft. cone

Jan 1, 1938