Search Documents

By R. V. Taborelli, P. B. Bucky

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By P. B. Bucky, R. V. Taborelli

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By S. Andrew Kulin, L. Kaufman

A general treatment of the broadening of X-ray double-crystal spectrometer rocking curves due to distributions of tilts and strains has been carried out. The results of this treatment have been applied to the case where dislocations in a crystal give rise to both tilts and strains. On this basis it is found that the rocking-curve halfwidth due to imperfections in the crystal, ßC , increases with increasing Bragg angle, 8. These considerations predict linear relationships between & and tan2 , and ßCand tan 8, for Gaussian and Cauchy distributions of dislocations, respectively. The zero intercept of the ßC us 8 curve, which is a measure of the degree of imperfection of the crystal, is found to depend directly on the distribution rather than the number of dislocations. In addition, the slope-intercept ratio for the ßc - ? curve has been calculated for both the Gaussian and Cauchy distributions. Experimental determination of the - 8 curves for a series of copper single crystals prepared by the Bridgeman and Czochralski methods yields results in agreement with the calculated slope-intercept ratio for a Cauchy distribution of dislocations. CERTAIN X-ray techniques have been used to study the perfection of single crystals. Gay, Hirsch, and Kelly have considered the spreading of spots into arcs on Debye-Sherrer rings due to imperfections. The Double-Crystal Spectrometer has also been applied to this problem.2 The characteristics of Double-Crystal Spectrometer Rocking Curves have been described in the literature by various workers.2-4 By assuming a random spacing of dislocations which give rise to a Gaussian distribution of misorientations relative to some mean orientation in a crystal Gay, et al.,1 arrive at the conclu- sion that the most probable misorientation is given by where h is the spacing between dislocations, and 8 and are the relative misorientations of neighboring regions. If ßC is the halfwidth of the rocking curve (the width at one-half the peak intensity) due to dislocations in the crystal then5

Jan 1, 1960

By Gunnar Thaning, Borje Bjorkvall

At LKAB Central Division for Metallurgical Research at Malmberget, Sweden, fired pellets are examined in respect to mechanical and reduction properties. The paper deals with descriptions of the test methods. It also involves the rationale for the choice of these tests. Their correlation to the blast furnace operation will be examined. The mechanical tests used are the ISO-tumbler test and the cold compression strength test. Concerning the metallurgical properties, experiments have shown that some superbasic pellets in particular have different disintegration properties in different temperature ranges. Pellets which have favorable reduction properties when tested under isothermal reduction at high temperature may disintegrate to a large extent under low temperature reduction. This is also valid for some types of acid pellets. Consequently, it was found to be necessary to determine the reduction strength both at high and low temperatures. In the low temperature range, the disintegration is measured by tumbling the pellets in soft reducing conditions at 600°C in a modified Linder test equipment. The high temperature reduction strength is determined under load in the Burghardt-Grebe equipment. However, in order to get more information of the high temperature strength, LKAB intends to introduce a softening test. The tendency of high temperature disintegration will also turn up in the swelling test. The swelling properties are examined according to a procedure developed at LKAB. In this test the pellets are subjected to free swelling without mutual contact. The reducibility of the pellets is recorded in the swelling test.

Jan 1, 1974

By R. F. Marande, R. S. Busk

THE magnesium-aluminum-zinc system contains most of the magnesium-base alloys used commercially, although in practice the ternary, alloys are usually modified by the addition of a small amount [ ] of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the object of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.1 [ ] All alloys reported were made in 15-lb. melts, superheated to 1700°F. for 15 min., cooled to 1400°F. and poured in sand molds. The test bars produced had a ½ in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. CONSTITUTIONAL DATA Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By A. C. Heath, E. H. Dix

The importance of aluminum-silicon alloys in thc light alloy field is now generally recognized. Where silicon was once considered detrimental to the properties of aluminum, useful alloys now contain as much as 13 per cent. Furthermore, silicon is present as an impurity in aluminum of even the purest grades. Iron is another important impurity in aluminum and likc silicon is found in small quantities in the purest aluminum available today. The manner of occurrence of iron and silicon in commercially pure aluminum and many of its alloys exerts a very pronounced influence upon their properties. The effect of large quantities of iron in aluminum-silicon alloys is so detrimental that it has been found necessary to limit the allowable maximum percentage to as low a figure as is consistent with quantity production and satisfactory physical properties. The intimate relation existing between iron and silicon in aluminurn and alurninum alloys makes necessary a more complete knowledge of this ternary system. This paper is divided into two principal parts, dealing respectively with aluminum-silicon solubility equilibria and the constitution of aluminum-iron-silicon alloys. Part I.—Aluminum-silicon Alloys The early work on this system was largely confined to determining the general form of thc diagram and in this respect the results are in good agreement. Briefly, alulninunl and silicon form a simple eutectifcrous series without compounds. Until recently the solid solubility of silicon in aluminum had not been accurately determined. Ipraenkell (1908) stated that aluminum will retain 0.5 per cent. silicon in solid solu-t'ion. Rosenhain, Archbutt and Hanson2 gave the maximum solubility as about 1.50 per cent. and added that "this solubility docs not appear

By P. K. Foster, A. McNabb

A consideration of the literature shows the inadequacy of Fick's Laws to describe the diffusion of hydrogen in steels below 400°C. These laws are modified an the assumption that hydrogen is delayed at fixed sites in the lattice. Approximate and exact solutions of the resulting nonlinear system are derived for simple geometrical shapes. The results qualitatively account for the observed anomalous behavior. Experimental methods for verifying the theory are suggested. 1 HIS paper presents a new analysis of the diffusion behavior of hydrogen in steel based on a physical model which supposes that hydrogen atoms wander in a random manner through the crystal lattice, but tend to get trapped or delayed at certain fixed sites uniformly distributed throughout the metal. These sites, which will be called traps, are regarded merely as potential wells of significantly greater depth than those encountered in regular regions of the crystal lattices and no assumptions are made concerning their nature or origin. The results of experimental studies of the diffusion of hydrogen in iron and steel have usually been reported in the literature in terms of a diffusion constant D derived under the assumptions that the hydrogen concentration C is governed by Fick's laws.1 Fig. I is a composite of published graphs of the man. ner in which the values of D, so derived, vary with temperature. It is convenient to consider this material in two categories; the high temperature results above 400°C, and the results at lower temperatures. The graphs 2, 3, 4, 5 in the first class lie within a factor of three of each other and are relatively consistent compared with the low-temperature values. There is an increasing divergence in values of D with decreasing temperature till at room temperature they are spread over three orders of magnitude. Small values of D have been obtained for work-hardened specimens.' It is evident that D is a function of other variables besides temperature in this range and that these neglected variables are in some way connected with the work hardening experienced by the specimen. In view of evidence for an interaction between hydrogen in solution and dislocations9'10 and adsorption on crack surfaces,' some doubts must be entertained about the validity of Fick's laws and their associated physical model of noninteracting particles in random motion through the medium. More direct evidence of their inapplicability to the diffusion of hydrogen in steel was first produced by Darken and smith." Consider the permeation of hydrogen through a plate of thickness a under a boundary concentration Co at the ingoing, and zero at the outgoing, face. If Fick's first law1 is valid, the steady state flux P, through unit area is DCo/a. In addition, the concentration C varies linearly throughout and Qo, the mean quantity of hydrogen in the medium, is co/2. Compare Qo with Q1 the mean quantity required to saturate the same specimen to a uniform concentration G. In this case Ql = Co and hence the ratio

Jan 1, 1963

By J. S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1983

By R. E. Mazurak, E. L. Ealy

At the Beckley mine in southern West Virginia, forecasting unstable roof conditions in advance of mining is accomplished by wing a rating system that combines historical information on mine roof failures with known mine geology. Failure frequency rates are derived for each category of roof rock composition, unit thickness, structure, and extraction ratio. In this manner, known geological environments are rated according to instability based on actual experience. Drill hole control and geological interpretation provide the basis for forecasting unstable conditions beyond working faces. The forecasting technique has assisted mine management in reducing fall frequencies by 80% over the past two years compared to the first five years of operation. This reduction in fall frequency was accomplished by modifying the plan of advancing sections to minimize mining exposure to unstable roof conditions.

Jan 1, 1983

By Jerome Strauss, Carl L. Shapiro

THIS is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years,, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I INFLUENCE OF BODY-CENTERED CUBIC ELEMENTS The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tantalum) are reviewed individually. Iron-carbon-chromium System.-In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts' concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.-Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. a; these results have received general approval. Iron-carbon-molybdenum System.-In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and Reed,8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-

Jan 1, 1943

By J. Marvin Weller, M. King Hubbert

Preliminary investigations were undertaken with a Megger Ground Tester in 1931 by Hubbert to determine whether the faults in Hardin County, Illinois, could be located by earth-resistivity surveys. The results of these investigations, which were in part presented before this Institute in 1932,1 were sufficiently promising to warrant a more extensive field program in the same general area the following summer. During the second season an apparatus of the Gish-Rooney type was employed because of its greater sensitivity and to avoid the troublesome correction for resistance of potential electrodes necessitated by the use of a Megger instrument. The discussion of earth-resistivity traverses which constitute the main part of this paper is based entirely upon the results of the second season's work. All of the traverses were made with a constant electrode spacing of a equal to 100 ft., and the four-electrode technique was employed. Successive stations in these traverses were spaced at intervals of 100 ft. and the line of electrodes was carried parallel to the line of traverse. The graphs of resistivity profiles presented here (Figs. 1 to 3) are plotted with resistivities in ohm-centimeters as ordinates and with distance divided into stations at 100-ft. intervals as abscissas. After the traverses were run by Hubbert the results were computed, the profiles plotted, and tentative interpretations were made by him. These curves and interpretations were then taken into the field by Wellcr, who made a careful geological examination along the lines of traverse for the purpose of checking and supplementing Hubbert's interpretations. Weller then constructed a geologic cross-section extending along the line of each traverse. The accompanying diagrams graphically illustrate the correlation that can be made between earth resistivity and geology in this area.

Jan 1, 1934

By Robert C. Edmiston

The measurement of temperatures in exploratory drill holes yields information on regional and local geothermal gradients and mean surface temperatures. This data may be beneficial to the mining geologist interested in the occurrence and oxidation of metallic sulfide minerals or to the mining engineer interested in subsurface temperatures or water movement. Additionally, the estimation of mean surface temperatures by the projection of thermal gradients to the ground surface provides data on which to evaluate infrared imagery as an exploration tool. Temperature measurements in 30 diamond drill holes in the Silver Bell mining district of Arizona show that a regional geothermal gradient of 2.45°C per 100 m increases to 3.03°C per 100 m near the ground surface. It is also found that an anomaly in the mean annual surface temperature of 0.5°C is associated with the shallow occurrence of disseminated sulfides. Changes in the geothermal gradient due to topography, water circulation, and formation changes also occur.

Jan 1, 1976

By Randolph Specht

A two year study was made of the waste disposal of the pebble rock phosphate industry. Solid slimes are impounded in large settling areas and the process water is re-used. Clear effluent was not found to be toxic to fish or animal life in field tests or in controlled experiments.

Jan 7, 1950

By H. B. Fuqua, B. E. Thompson

The area discussed herein, commonly known as the North Texas district, embraces the following 10 counties: Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita and Wilbarger. It is underlain by two major structural features. The northernmost portion of the district, including Cooke, Montague, northern Clay, Wichita, Wilbarger, Foard and Hardeman counties, is underlain by the system of buried mountains known as the Red River uplift, which is parallel to and closely related to the Wichita-Amarillo uplift of Oklahoma and the Texas Panhandle. While the presence of a great majority of the numerous oil fields of the area is traceable to this feature, the production in Archer, southwestern Clay and southeastern Baylor counties is due to the influence of what is known as the Cisco Arch (so called because of its influence on Cisco deposition), the axis of which extends in a north\lest-southeast direction across Archer County. Discussion of Tables Preliminary to discussing developments during the year 1933, it appears advisable to offer a few words of explanation on Tables 1 and 2, included as part of this paper, in which an effort has been made to sumlllarize oil and gas development in North Texas to Jan. 1, 1934. One of the chief objectives of this publication is understood to be to show production by individual pools, and, if possible, by distinct pays in a pool. This the authors haw been unable to do for North Texas. It is a generally recognized fact that there are well over 100 individual pools, which should perhaps be mow properly called "productive spots," in Archer county alone, with perhaps an even greater number in Wichita County. It can be found upon investigation that an apparently continuous productive area covering Many acres consists of a half dozen lenticular sands, all stratigraphically different,, which produce only under portions of the apparently continuous area. It is also a fact that practically all gross production records are carried by the various intcrcsted parties by major districts or by counties. It is obvious therefore

Jan 1, 1934

By Arnulf Muan, Klaus Schwerdtfeger

Activity-composition relations in Pt-Cr and Pd-Cr alloys of low chromium concentrations UCr < 0.3) have been determined in order to ascertain quantitatively the extent of reactions to be expected between Cr2O3-containing oxide phases and platinum or palladium crucibles used as containers in studies of oxide equilibria at low oxygen pressures. This work is a continuation of similar work previously

Jan 1, 1965

By H. Hu

Observations were made on the recrystallization of a 70 pct cdd-rolled silicon-iron crystal with an initial orientation of (113) [332]. Its polygonization and recrystallization characteristics were studied. Results indicated that re crystallization tendency of the deformed crystal is much weakened by the polygonization of the matrix. Complete recrystallization in such specimens is achieved by the growth of recrystallized grains of sufficient size and of the right orientations in relation to the matrix. Evidence was also furnished which suggests that the difference in the re-crystallization tendency is a result of the difference in the severity of lattice bending rather than the difference in orientation of the deformation texture. DUNN and Koh1,2 have made an extensive study on the rolling and annealing textures in silicon-iron crystals. Their results indicated that the recrystallization tendency can be widely different in crystals with different orientations. A particularly interesting example of their results was a crystal with an initial orientation of (113) [332], which developed a deformation texture of (001) [110] after 70 pct cold-rolling. Recrystallization in this crystal took long time anneals at high temperatures. Other crystals having different orientations recrystallized very rapidly. Wiener and corcoran3 have observed the retention of the (100) [011] deformation texture in a low-temperature annealed specimen of a commercial silicon-iron alloy, corresponding to areas of light-etching low-angle boundaries in the annealed struc-

Jan 1, 1960

By F. J. Fayers, J. W. Sheldon

A theoretical discussion is presented of the behavior of the interface between two fluids of different physical properties when displacement is occurring along a thin tilted bed. An approximate equation of motion is deduced for the motion of the interface, suitable boundary conditions are derived and the conditions necessary for the approximation to be valid are determined. Steady-state behavior and the circumstances under which a steady-state interface can develop are discussed. Finite-difference solutions of the equation of motion for two characteristic water-drive problems are presenled. The theory of displacement in a thin bed may be regarded as being the porous-medium-equivalent of the classical "shallow-water wave" theory of hydrodynamics. INTRODUCTION The solution of moving interface problems are important in predicting the behavior of oil reservoirs under various conditions of production. Kidder4,5 has obtained analytic solutions for the fingering problem and for another particular case of the motion of the interface between two immiscible fluids of unequal density in a porous medium. In the present analysis, we analyze the problem of the motion of an interface along a slightly dipping bed whose length is long compared with its thickness. The requirement of a thin bed is necessary in order to give a simple differential equation for the motion. The two fluids are of unequal density and mobility. In the derivation of the equation of motion, it is assumed that the lighter fluid is being injected at constant rate at the high end of the porous layer, while heavy fluid is produced at the low end of the layer. The analysis applies equally well, however, to the reverse procedure in which the heavier fluid is injected at the low end of the tilted layer. It will be shown that the behavior of the system is critically dependent on which fluid has the higher mobility and that the interface can in certain circumstances achieve a simple progressive steady-state shape. The fluids may be considered to be immiscible or miscible. It is assumed, however, that the thickness of the interface region is negligible in comparison with other dimensions of the system, and that the strength of the saturation or concentration discontinuity remains constant during the motion. In conjunction with Buckley-Leverett theory and areal sweep-out calculations, the tilted interface problem is one of the fundamental problems of reservoir engineering; it defines the very important underpassing and overpassing phenomena associated with water-drives, gas-drives and secondary recovery operations. The tilted interface problem has been dealt with previously by Dietz.2 In the present paper, we endeavor to derive the pertinent mathematical results more rigorously, and in doing so we obtain modifications in both the differential equation and boundary conditions for those given by Dietz. We also attempt to show the connection between these results and some of the recent work on the stability of interfaces. Finally, we attempt to demonstrate the practical importance of the thin bed theory by showing the difference in behavior of two characteristic waterflood problems. In the favorable mobility case recovery is improved by increasing production rate, while in the unfavorable case undercutting or overcutting is minimized by reducing the displacement rate. PROPERTIES OF THE EQUATION OF MOTION Fig. 1 illustrates a porous layer of constant thickness H and tilt 8 with Fluid 1 of mobility ?l and density pl below Fluid 2 of mobility ?2 and density p2. The fluids are incompressible and flowing with volumetric flux q along the layer. Both the slope a of the interface with respect to the bed and the curvature of the interface are assumed to be small. What is meant by "small" is indicated in the derivation given in Appendix A of an approximate equation of motion for the interface. Other symbols are defined in the "Nomen-

By Felicia F. Peng

The computer graphic routines and digital simulation program of coal cleaning circuits have been developed in the Mineral Processing Engineering Department, West Virginia University. The functions of the program include computing, tabulation and graphing of 1) washability characteristics of raw coals, 2) blending, 3) Tromp distribution curves for two washer types-- water only and dense medium, 4) predicting the functional relationship of yield and qualities of clean coal product in individual and overall coal cleaning circuits in coal preparation plant, and 5) determining the optimal clean coal yield based on the market and environmental specifications. Amdahl 470 V/7A digital computer, Tektronic 4025 graphic terminal and Tektronix 4663 digital plotter with Fortran IV are used to achieve the goals. The simulation with the aid of graphic routine program of coal cleaning circuits is a useful tool for coal preparation engineers in evaluating the feasibility of proposed flowsheets, in investigating the effect of a modification in a unit operation of an existing plant, in analyzing the off-line optimization, and in comparing the alternative circuit control strategies. The coal cleaning process simulation with graphic routine can contribute greatly to the decision making processes of preparation plant design.

Jan 1, 1983

By Hillary W. St. Clair

An equation is derived for the rote of reaction of a sphere of metal oxide in a restricted enclosure through which a reducing gas is flowing. The equation takes into consideration the reaction rate coefficient, transport through the gas and through the porous shell of reduced oxide, the rate of gas flow, THIS paper describes a mathematical study of the chemical and physical processes that determine the rate of reduction of solid metal oxide with a reducing gas. The study was a part of a theoretical study leading to the development of a mathematical model for the simulation of the thermochemical behavior of the iron blast furnace. An essential feature of such and the volume of- space surrounding the sphere available for gas flow. The equation is applied to experimental data on vote of reduction of iron oxide in hydrogen. The equation serves as a model for predicting the course of reduction of a particle of. metal oxide in a shaft furnace. a model is an adequate mathematical relationship defining the rate of reaction in terms of all the important chemical and physical phenomena that affect the rate of reaction. This includes not only the reaction rate coefficients, equilibrium ratios, gas composition, and temperature, but also the relevant physical properties of the oxide, rate of gas flow, and relative volumes occupied by gas and solid. In many previous experimental studies of the rate of reduction of oxides by hydrogen or carbon monoxide, the rate of reduction was assumed to be controlled primarily by the chemical reaction at the

Jan 1, 1965

By C. G. Dunn, J. L. Walter

A study has been made of the nature of the slow growth or nucleation stage of secondary recrystallization to the cube texture in sheets of high-purity 3 pct SiFe. Cube-oriented nuclei were identified and their growth observed, using surface markings together with micrographic and X-ray techniques to provide information on grain boundary interactions and the driving forces for growth. FACTORS that promote growth of certain grains during the early stages of secondary recrystallization have been considered theoretically1 but have been little explored in a direct experimental way. In certain cases,2&apos;3 it has been reported that the primary recrystallization grains (nuclei), which eventually become secondaries, were found to be larger than the other grains into which they grew-Factors such as grain boundary "mobility" and differences in strain energy may contribute to the

Jan 1, 1961