Search Documents

By A. L. Marshall, F. J. Norton

TO determine how rigorous a treatment was necessary completely to remove sorbed gases from molybdenum electrodes in vacuum tubes, the degassing process in high vacuum was studied in the temperature range 800° to 2300°C., and the gases analyzed. Some work was also done on the degassing of tungsten, nickel, and carbon. It was shown that the amount of gas is proportional to the mass of the sample and not to the surface area, indicating that the gas is distributed through the body of the metal. A study was made of the solubility of nitrogen in tungsten and molybdenum from 1200" to 2400" C., at equilibrium pressures from 0.01 to 760 millimeters.

Jan 1, 1933

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. Table I (Jones, 1973) affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 (Anon., 1967) is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak-type brines, produced mainly for lithium. Market Attributes Some of the important market traits common to industrial minerals used by the chemical industry are listed below. 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. For example, fluorspar from China and Thailand normally goes to Japan, while South African fluorspar can go either to Japan or to the US. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities.

Jan 1, 1983

By E. C. Harder

IN view of the gradually decreasing known reserves of high-grade manganese ore and the rapidly increasing consumption of iron-manganese alloys in the steel industry, it is well to turn our attention to the development of low-grade manganiferous ore deposits and to the utilization of these ores in steel manufacture. The dependence of this country on imported manganese ore and ferromanganese has been forcibly brought to the attention of steel makers during the last few years by the cessation of manganese-ore imports from Russia, the restriction of manganese-ore imports from India and of ferromanganese imports from Europe. Should the importation of manganese ore from Brazil cease, the steel industry of this country would face a serious situation. The present practice of steel making requires ferromanganese in large quantities and ferro-manganese of the grade used at present can be produced only from high-grade manganese ores such as the United States appears to possess only in insignificant amounts. There are in the United States, however, large reserves of manganiferous iron ore which could probably be used extensively in the steel industry if certain changes in the practice of steel manufacture were made. Thus high-grade manganese ore could be conserved. Among the most important deposits of manganiferous iron ore in this country are those of the Cuyuna iron-ore district of Minnesota. It is probable that in case of restriction of foreign supplies, the users of manganese in the United States would have to rely to a large extent on the Cuyuna district to make up the shortage.

Jan 9, 1917

By R. Hogg, F. F. Aplan, P. B. Bradley

The mineralogy of the solids contained in the black-water effluent from coal preparation plants has been investigated. Samples were obtained from 13 locations, representing major coal seam in the Appalachian, mid-continent, and western regions of the United States. On the average, the samples were found to contain 60% carbonaceous material with the balance as mineral matter. The mineral fractions from all of the samples from the eastern half of the United States were found to be remarkably similar, consisting of over 50% illitic clays; about 10-15% each of kaolinite, calcite, and quartz; and lesser amounts of chlorite and pyrite. The western samples were somewhat different, generally containing significant quantities of montmorillonite clay. Flotation may be wed to recover additional clean coal contained in the black-water discharge.

Jan 1, 1981

By Oscar Kuchs

IN January and February of the current year, at the Tooele plant of the International Smelting Co., Tooele, Utah, a modification of the usual method of converting, for the treatment of copper-lead matte from lead blast- furnaces, was developed and put into successful operation. In brief, the method consists in blowing molten matte direct from the blast furnaces in basic-lined converters, without the addition of siliceous fluxing ores, to the almost complete elimination of the lead contained, and to the production of copper bullion, the resulting lead fume being recovered by the filtration of the converter gases through woolen fume bags. The process is carried out in conjunction with the converting of reverberatory copper matte, the heavy iron slag, together with the copper precipitated, being transferred to converters blowing copper matte. The purpose of this transfer is to reduce the copper oxide formed, due to the necessary overblowing of the lead-matte charge, and to utilize, as far as possible, the value of iron from the lead matte, for the fluxing of siliceous dry ores. The final slag from the copper converters is then skimmed off and transferred molten to a reverberatory smelting furnace treating copper ores. This variation from general converting practice was the outgrowth of results obtained during 1913 when it was endeavored to convert copper-lead matte in the usual manner, with the direct addition of siliceous fluxing ores. To make clear the reasons lying back of the process it is necessary to recount at some length the results of operations during that year. In the design of the lead plant it was planned to treat the copper-lead matte from the furnaces by direct converting without reconcentration and thereby to recover the copper, silver, and gold as quickly as possible. A converter plant of ample capacity, treating copper matte, already being in operation, it was only necessary: to install a bag house, a fan, and the necessary flues to complete the equipment.

Jan 7, 1914

By H. M. Chance

RECENT research work has shown that coal can be produced, at reasonable cost, from almost all coal-mining districts containing not more than 3 to 8 per cent. of ash. From coal so produced, an abundant supply of coke, suitable for blast-furnace operation, can be made containing from 12 down to 6 per cent. or less of ash. These statements apply broadly to the Appalachian coal belt, including most of the mining districts in Pennsylvania, Ohio, West Virginia, Kentucky, Tennessee, and Alabama. The exceptions will generally be found among those coals carrying a prohibitive percentage of sulfur. Any gravimetric heavy fluid method of separation will effect a reduction in the percentage of sulfur, but this reduction may not be sufficient to produce, from coal unfit for metallurgic use, a product that can be so used. When a large part of the sulfur is in the form known as "organic sulfur, "or is present as very .finely disseminated and homogeneously distributed pyrite, possibly it cannot be eliminated from the low-ash coal produced. When the sulfur exists as pyrite in distinct layers, bands, or nodules, or when it is finely disseminated but is irregularly distributed, often a low-ash coal low enough in sulfur to make good metallurgic coke can be produced from relatively impure coals. It has generally been assumed that the quality of coke on which blast furnaces must be operated depends on the geographic location off the furnace, and that the grade of coke on which a blast furnace must operate is that produced from the best coal obtainable by careful mining; or if the coal is prepared by washing, hand picking, or other means by which the foreign impurities are removed, that the grade of coke on which the furnace must operate depends on what has been termed the "inherent ash" of the particular coal.

Jan 6, 1924

By D. W. McGlashan, K. N. Mcleod

IN the use of free bubbles with precise temperature control and continuous pH measurement, the contact angle apparatus differs from all previous equipment. Experimental procedures differ sharply from the captive bubble method1,2 of introducing the gaseous phase in the three-phase system. When freed from the tube and captured by a solid surface, a bubble more closely conforms to the spherical ideal set up by the usual mathematical analysis of surface free energy or surface tensional relationships of the forces involved. The assembled equipment, Fig. 1, departs from the usual contact angle apparatus in providing: 1) water circulation for fixing temperature, 2) instruments to measure and record pH during testing, and 3) a system for producing and using free bubbles. The apparatus allows testing over a broad range of closely controlled conditions, and the use of free bubbles gives contact angles independent of operator manipulation, which was unavoidable in the older captive bubble method. A bubble released below the specimen rises through the liquid and contacts the mineral. If the mineral is gas-avid the bubble adheres, developing a finite contact angle. Reaction cells (1), 2x33/8x5 3/16 in. ID, are of pyrex glass 5 mm thick. To prevent optical distortion, the sides are optical flats and are planed parallel to within five wave lengths of light over the entire surface. Special cement is required to withstand chemical attack and thermal shock. The cell is placed in a thermal jacket (2) made of welded aluminum. A water seal for the optical ports is made by using O-rings tightened against the flats of the cell by fine-threaded and adjustable ports, Fig. 2. In-flow water is discharged downward from a manifold located near the bottom of the cell jacket. Water overflows the weirs at each end of the cell jacket, discharging from both sides to a collecting manifold (24). A hose (26) leads the overflow water to the thermal-conditioner well (4), which is recessed to accommodate a reaction cell and two beakers (150 ml). Both the thermal jacket and the thermal-conditioner well are insulated to minimize the effects of temperature differentials. Water, discharging from the thermal-conditioner well, returns to a thermostat bath and pump (3), from which it is pumped to the thermal jacket. The thermostat bath permits temperatures to be adjusted from 1" or 2°C to 80°C and will maintain the selected temperature within 0.2ºC. An electrode support (22) groups the four electrodes (8) so that they fit conveniently into the reaction cell, Fig. 2. This assembly holds the glass electrode, the calomel electrode, the temperature-

Jan 1, 1957

By Haydn H. Murray

Although alumina constitutes about 15% of the earth's crust, it is expensive to separate and purify for the production of aluminum with the exception of the alumina in bauxite. The United States has a variety of nonbazurite resources that could substitute for bauxite, including high alumina clays, alunite, dawsonite in oil shale, anorthosite, and nepheline venite. Each of these resources is discussed from the standpoint of geology, geography, processing, and potential recovery. Potential byproducts include alica from clays, potash and sulfuric acid from alunite, soda ash from dawsonite, and soda ash and potash from anorthosite and nepheline syenite.

Jan 1, 1983

By Robert H. Weber

INCREASING acceptance of perlite products, chiefly in the fields of lightweight structural aggregates and thermal and acoustic insulation, has led to expanding market demands that have encouraged many new producers to enter the field. In some instances, however, the failure of these producers to anticipate the variable response of perlite to conventional processing methods has led to difficulty in establishing an economical flowsheet by which a predictable specification product could be obtained. It is not the writer's intent to provide a solution to these problems, but rather to summarize their nature. It is to be hoped that members of the industry who have hurdled some of these obstacles will document solutions arising from their experience. In this treatment the term perlite will not be restricted to the petrographic definition but will apply to all volcanic glasses. Expansible obsidians and pitchstones are accordingly included in this broader industrial classification. Chemical Properties: Although perlite has been reported to range in composition from that of rhyolite to that of andesite, it is probable that most of the glasses have the composition of rhyolite. When recalculated to an anhydrous basis, the five analyzed glasses from New Mexico, representing five distinct physical types from widely separated deposits, show an amazingly uniform oxide composition. Water content is the only major compositional variable; total water ranges from a low of 0.37 pct (non-expansible obsidian) to a high of 8.95 pct (expansible pitchstone). The wide range in expansion characteristics exhibited by these samples cannot be related to significant variations in the composition of the nonvolatile fraction and has been only partially correlated with variations in water content.

Jan 1, 1956

By Major N. R. Junner

Although manganese-garnets are rarely seen in hand specimens of the manganese ores and associated rocks, they have been detected by the writer in thin sections of all the ores and wall rocks that have been sliced, with the single exception of the Insuta deposit. Rhodonite, and an almost colorless amphibole, which appears to be manganiferous, are less common. Types of Occurrence (a) Rocks Composed of Manganese-garnet and Quartz The best known examples of this type are from near Bole and Wa in the Northern Territories of the Gold Coast, and from near Chama in the Gold Coast Colony. Normally these are fine and even-grained rocks, in which the garnets cannot be recognized in hand specimens. They are often stained with secondary manganese oxide. Thin sections examined microscopically are seen to be composed of aggregates of minute crystals of garnet in a matrix of mosaic quartz. Some manganese oxide and braumite (?) is often present, but other minerals are exceptional. The relative proportions of garnet and quartz in these rocks vary greatly and there is a complete gradation from quartz-rock to garnet-rock. (6) Rocks Composed Mainly of Manganese-garnet and Manganese Oxides Rocks of this type are known from Kalimbi Hill near Siripe, Pabini Hill near Bangwon, near Odumase and Konongo, and in the Ya Ya creek, about 5 miles east of Dunkwa. These are usually fine-grained banded dark-colored rocks, composed of abundant minute garnets in a matrix of black manganese oxide and braunite (?). A little microcrystalline is often present, and occasionally a little colorless amphibole. quartz (c) Rocks Composed of Rhodonite and Manganese-garnet Rocks of this type are not common. They are known from near Chama, and from the road between Senyong and Mangkuma. Some quartz is usually present. All these rocks resemble closely in texture and composition certain rocks from India, described by Fermorl as "gondite;" and they also resemble certain rocks described by Derby2 from the Queluz district,

Jan 1, 1927

An ore search for commercial titanium-bearing ore deposits is in progress by the Crane Co., manufacturers of valves, because they expect this metal to be important in valve manufacturing in the future. The company will eventually be mining and making titanium sponge. At present they are buying titanium tetrachloride from the Stauffer Chemical Co, at Niagara Falls and making titanium by reaction with magnesium. Production from the Babbitt concentrator of Reserve Mining Co. is scheduled to begin in late 1951 or early 1952. The capacity is to be 300,000 tons of pellets per year made from magnetic taconite concentrates.

Jan 7, 1951

By C. D. Rubert, W. J. Parton

A flotation plant was placed in operation in 1945 at the Tamaqua colliery of the Lehigh Navigation Coal Co. Inc., to recover fine anthracite which is discharged from the cleaning plant with the washery water.‡ In addition to the recovery plant, facilities were provided for the complete clarification of the washery water, recirculation of this clarified water for breaker use, and disposal of the refuse solids in a waste impounding dam. Fig I shows a view of the settling tanks and the flotation plant. Flow Diagram The flow diagram for the complete recovery project is given in Fig 2. All the waste water from the cleaning plant is collected in a sump A outside the breaker structure, from which a 7000 gpm pump B delivers it through a 16 in. line to a 75-ft diam hydroseparator C. The hydroseparator, acting as a classifier, is set to give a separation at approximately 200-mesh. The minus 200-mesh overflow is discharged by gravity into the 180-ft thickener D for final settling of the solids. The classifier underflow sludge is pumped to the flotation plant by a 6-in. quadruplex diaphragm pump E. A 10-ft diam hydroseparator F is used to make a second classification on the sludge solids at approximately 28-mesh. The underflow from this classifier containing the coarse particles is elevated by a 6-in. diaphragm pump G and is discharged on two 4- by 6-ft vibrating screens II. These screens are dressed with approximately 28-mesh cloth. Screen oversize product flows directly to the centrifuge that dewaters the cleaned froth. The screen underflow and the overflow from the 10-ft classifier flow to the flotation circuit. The flotation feed is conditioned in a 12 by 12-ft agitator tank J at a pulp density of I:2.33 (30 pct solids). Reagents are fed to the circuit by reagent feeder I. The conditioned pulp is then diluted to a pulp density of approximately I: 5 (18 pct solids) and is fed to two banks of four 100-cu ft froth flotation cells K for primary coal recovery and cleaning. Additional reagents from reagent distributor L are added to the feed weir-box of Nos. 2, 3, and 4 cells of each bank of flotation machines. Clean coal removed from these cells flows directly to the clean-coal sump. Dilute tailings from the primary cells is re-thickened in a 30-ft diam thickener M and is then retreated in a scavenger circuit for final recovery of coal. The scavenger circuit consists of a 6- by 6-ft agitator tank N and two banks of four 24-cu ft froth flotation cells 0. Coal froth from these cells flows to the dewatering equipment and the tailings flows to a vertical refuse pump which delivers it to the 180-ft diam waste thickener D. Dewatering of the coal products is accomplished in a 54- by 72-in Bird centrifugal filter P. The cake product is dropped onto a conveyor and is loaded

Jan 1, 1949

By A. Tobey Yu, David A. Kinneberg

As the heart of a copper-producing complex, a smelter converts raw copper concentrates or leach-plant precipitates, or both, into blister copper. A typical smelter feed also contains matte chips, flue dust, flux, and lime. All these materials vary widely in their characteristics, ranging from sub-micron to lumps, from slurry to dust, from abrasive to corrosive, and free-flowing to adhesive. Handling all these materials becomes even more problematic since most of the world's open-pit copper mines are located in a semi-arid zone where rainfall is minimal.

Jan 12, 1976

By B. B. Rath, Hsun Hu

In wedge-shaped bicrystals of zone-refined aluminum it is observed that (111) pure tilt boundaries migrate under the driving force of their own inter-facial free energy. The boundary velocity is a power function of the driving force. The driving force exponent decreases with decreasing angle of misorien-tation. For example, at 64O°C, the exponent decreased from 4.0 for a 40 deg to 3.2 for a 16 deg tilt boundary. An evaluation of the driving force acting on the boundaries during their motion indicates that for low driv-forces, up to about 2 x l03 ergs per cu cm, the velocity is relatively independent of misorientation, whereas at higher driving forces a 40 deg tilt boundary exhibits the highest velocity. The measured activation energy for boundary migration approaches that for bulk self-diffusion at low driving forces, decreasing from 33 to 27 kcal per mole as the driving force is increased from 1 x l0 to 5 x l03 ergs per cu cm. These results are compared with current theories of grain-boundary migration. In previous experimental studies of grain boundary migration the driving force has been limited to a difference in stored energy across the boundary. This stored energy has been introduced into the crystal either by prior deformation1-3 or by grown-in lineage structure. A part of the energy stored in the deformed crystal is released by recovery either prior to or concurrently with grain boundary migration, thus introducing an uncertainty as to the magnitude of the driving force responsible for grain boundary migration. The grown-in lineage structure, though thermally stable during annealing, neither provides conditions under which different levels of energy may be stored in the imperfect crystal nor provides a control of orientation difference across the migrating boundary of a growing grain. Furthermore, because of variation in the lineage structure, it is difficult to determine accurately the energy stored in the imperfect crystal. Several investigations of grain boundary migration during normal grain growth have also suffered from difficulties in estimating the driving force because of uncertainties in the principal radii of curvature.~ In the present investigation the velocity of pure tilt boundaries in zone-refined aluminum bicrystals of selected orientation (40, 30, and 16 deg around the [Ill] tilt axis) has been measured in the absence of a dislocation density difference across the moving boundary, thus eliminating the previous experimental difficulties. The driving force for boundary migration is derived from a gradient of the total interfacial free energy of the migrating boundary in wedge-shaped bicrystals. A similar method was attempted by Bron and Machlin in a study of grain boundary migration in silver. However, they found that one of the crystals was deformed and consequently the motion of the boundary was partly due to a difference of stored energy across the boundary. The observed behavior of boundary velocities as affected by the driving force is examined in the light of the predictions of the current theories of grain boundary migration.7"10 The effect of boundary misorientation on velocity is compared with the theory of " which is based on a dislocation core model for high-angle boundaries. EXPERIMENTAL METHOD Seed-oriented bicrystals of zone-refined aluminum, 2.5 cm wide, 0.5 cm thick, and 12 cm long, containing tilt boundaries with a common (111) axis, were grown from the melt in the direction of this axis. Spectro-graphic analysis, reported earlier,'' indicated the purity of the crystals to be 99.999+pct. Three such bicrystals containing 16, 30, and 40 deg tilt boundaries were used. Wedge-shaped specimens were prepared from these bicrystals by spark cutting followed by electrolytic polishing. The angle of the wedge was usually 40 deg and the specimens were usually 0.25 cm thick. The intercrystalline boundary was located within 0.2 to 0.5 cm from the tip of the wedge. Fig. 1 shows a section of an oriented bicrystal containing an outline of a wedge-shaped specimen. The crystallographic directions shown in Fig. 1 represent the orientation of one of the crystals (the larger section of the bicrys-tal); the orientation of the other crystal differs only by rotation around the common [lil] axis. The parallel faces of the wedge always corresponded to the common (171) planes in both crystals, whereas the orientation of the side faces varied, depending on the misorientation angle. The bicrystal orientations were determined

Jan 1, 1970

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By Frederick N. Rhines

Because of the nature of the environments in which metals are handled, it is natural that gases should be suspected of intruding into metallurgical operations, there to produce effects both beneficial and detrimental. The problem of tracing and controlling such effects is often made difficult by the complexity of the conditions surrounding their occurrellce, even though the fundamental mechanisms invalved may be simple and of familiar type. Many gas-metal reactions are known to be implemented by Processes of diffusion. These form a homogeneous group of phenomena which become more readily understandable when viewed together, in that the knowledge gained from one serves to interpiet the next. It is the purpose of the present Paper to present, by means of examples drawn from practice, a brief survey of the ways in which gas-metal diffusion serves and obstructs the Purposes of the metal-fabricating industries. The selection of the cases described was made by consulting more than thirty-six practicing experts whose combined experience provided an extensive coverage of the field and who were in a position to supply examples of occurrences of present day interest. The response was generous and it is regrettable that space permits the description of only a limited number of typical examples with ' but brief mention of parallel cases. The Nature of Gas-metal Diffusion The term ugas-metal diffusion," although commonly used, is ambiguous in so far as it implies that a definite group of " substances may be identified as gases and may be expected to behave in a manner distinct from other substances in association with metals. "Gases" such as oxygen and hydrogen when diffusing through a liquid or solid metal are properly components of the liquid or solid solution; they behave as alloying elements and are not to be distinguished in their diffusion characteristics from other elements, except that each has an individual rate of diffusion. On the other hand, a number of metals in certain.temperature ranges are volatile to the extent that they may appear in the form of vapor in metallurgical operations. For the sake of greater definiteness, therefore, it will be convenient to regard as "gas-metal diffusion" any process in which the result depends upon one or more of the diffusing elements appearing, at some stage, in the gaseous state, or as a compound gas. NO element, gaseous or otherwise, can diffuse through a liquid or solid metal unless it is at least slightly soluble in that metal. The elements of low atomic number

Jan 1, 1944

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

By C. S. Barrett, C. T. Haller

Twinning in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study1 concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: 1. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on (102) planes causes a re-orientation of the crystal lattice by 86", it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane— the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallo-graphic observation, for it was found

Jan 1, 1947

GENTLEMEN : Herewith are transmitted the reports of your Treasurer and the Chairmen of your standing committees on Admissions, Membership, Papers and Publications, and Library for the calendar year 1931. To these reports you are referred for further details of the year's activities. Finances.-Depressed industrial conditions prevailing throughout the year were reflected in a substantial decline in current revenue. Aside from interest on sundry special funds (but including that from the Life Membership, Library, and General Reserve Funds) total receipts amounted to $168,274, compared with $194,636 in 1930. The principal items of decrease were $17,000 in advertising income from the monthly magazine MINING AND METALLURGY, and about $9,600 in dues and initiation fees. Of this shrinkage $4,000 is accounted for by decrease in the number of new members enrolled; and $5,600 by diminished income from current dues and arrearages. This naturally has coincided with an \ increase in delinquency and "drops" or suspensions for nonpayment of dues. The decline in advertising income, amounting to 38 per cent as compared with that of 1930, in general paralleled the experience of all technical and trade publications; and it is problematical whether 1932 will show as large a return from advertising as did 1931.

Jan 1, 1932

By Thomas Fraser, David R. Mitchell

THE primary purpose of the loading plant is to transfer the finished product from the preparation machines to the railroad car, truck, or barge in which it is to go to market. Secondary purposes of the loading plant are: to prevent excessive degradation of sizes during loading, to reduce segregation as much as possible, and to prevent excessive quantities of very good or off-grade coal from entering any one car. Nonuniformity of consignments is one of the chief sources of complaints by consumers and coal merchants. A properly designed loading plant will do much to reduce complaints and insure uniformity, not only from shipment to shipment but also in each individual consignment along the length of the car and in cross section. DEGRADATION IN STORAGE, LOADING AND SHIPMENT The object in loading is not only to handle the coal without breakage and segregation, but also to produce a well-trimmed load that will ride to its destination without spillage o~ breakage en route. The small sizes present in a car-of prepared coal as received by the purchaser consist of: missed small sizes not screened out in the preparation plant, breakage during loading, and breakage caused by handling en route. For domestic sizes of anthracite shipped from the Pennsylvania anthracite field to Atlantic coast cities, the dealers' loss because of breakage in loading and shipment amounts to from 2 to 5 per cent and for anthracite shipped to Middle West cities, the loss is 8 to 9 per cent. This difference is in part because dealers in the Middle West rescreen their coal more thoroughly than is usual in the East. One dealer handling Illinois No. 6 coal shipped from southern Illinois mines to Chicago reports an average size loss of 10 per cent when lump coal is unloaded with a fork. This runs as low as 5 per cent for carefully loaded coal and as high as 15 per cent for carelessly loaded coal. An Ohio dealer estimates the degradation in loading and shipment of West Virginia coals consigned to Ohio cities as follows: Pocahontas lump

Jan 1, 1950