Search Documents

By H. E. Gross

A plausrsle method of drilling beyond the continental shelves is set forth with limitations of the method. The continental shelves comprise the water-covered portions of land masses out to 600 ft. of water, or roo fathoms. The problems and possibilities of drilling beyond this depth are discussed in this paper. Introduction Much attention is being given the problem of developing petroleum beneath the open sea. Geophysical surveys have been made 26 miles offshore1 from the continental United States, and onco offshore ownership is established it is likely that there will be drilling for oil on the continental shelves. More than two years ago the author presented the means for drilling in deep water.2 at the fall meeting of the Petroleum Division of the AIME at Los Angeles. His concepts then were based on the use of rigid foundations suitable for drilling in water up to 600 ft. deep. The present paper suggests a method for drilling in deeper water. Possibilities and Problems of Drilling beyond the continental shelves It being conceded that because restricted deep-water portions of the hydrosphere might contain oil in commercial quantities, and that at any rate it is pertinent to know more of the nature of the lithosphere beneath the hydrosphere, the possibilities and problems of drilling beyond the continental shelves should be set forth. Drilling in open water would offer few if any advantages over drilling on land. These are: 1. The ocean transportation is available to deep-water drilling sites, and extensive pipe lines and roads are unnecessary. 2. Refinery facilities and markets perhaps are established on the near-by shore where adjacent fields on land are nearing depletion. 3. There is freedom from jungle pests and tropical diseases. 4. Competitive drilling is less likely. 5. Extensive areas attractive for development arc not yet under lease or concession. Disadvantages are great and numerous: 1. Storm hazards from wind and wave. 2. Expensive foundations, either rigid or floating. 3. Shutdown times because of weather. 4. Marine Regulations of Federal Bureaus in addition to customary regulations on land. 5. Frequent difficulty in moving men and materials to and from drilling platforms. 6. Extra precautions required in open sea. For drilling in water more than 500 or 600 ft. deep, rigid foundations2 become too costly, and floating foundations must be used, and they must meet the following requirements:

Jan 1, 1947

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By Maurice C. Fetzer, Charles R. Austin

It has long been known that plain high-carbon steels may be susceptible to graphiti-zation below the A1 critical, but no data have been available to indicate what factors cause and tend to inhibit graphite formation. Two recent publicationsl,2 have shown that the factors controlling graphitization below the A1 are different from those operating above the A1 inversion where commercial graphitization of malleable iron begins. Furthermore, for plain high-carbon steels graphitization below the critical point does not appear to be related to ordinary chemical analyses. Many years ago it was recorded3 that the rate of graphitization at subeutectoid temperature is not a maximum just below the A1 critical, but at some lower temperature, which Austin and Norris have shown to be about 670°C. Indeed, work done in our laboratory has demonstrated that it is impossible to spheroidize certain steels in the temperature range of 650° to 710°C. without the formation of considerable amounts of graphite. However, if the temperature is maintained just below the A1 (720°C.) these same steels may be completely sphe-roidized at constant temperature. In previous studiesl,2,4 on I per cent plain carbon steels graphitization was encountered during prolonged tempering. The limited number of steels studied did not provide sufficiellt data to permit adequate study of the factors controlling this graphitization. Accordingly, a limited statistical investigation was undertaken, utilizing 18 steels of similar chemical analyses, furnished by four steel companies, who also supplied information regarding the history of manufacture. An extensive program of research is being carried out on these steels, including the effect of pretreatment and atmosphere on the nature and extent of graphitization, and the possible correlation of graphitization with such characteristic properties as hardenability, grain size and mechanical behavior. In the present paper discussion is restricted to a study of the correlation between graphitizing tendency at 670°C. after quenching from several temperatures above the critical, and (I) the minor variations in the chemistry of these steels of "similar" chemical composition, and (2) the deoxida-tion practice employed. The state of the lead bath, oxidized or protected from oxidation by charcoal, used in the tempering treatments is also considered. Materials Eighteen plain carbon steels of about I per cent carbon, and containing similar amounts of each of the other common elements usually found as impurities, were obtained in the form of rods % in, in diameter from four steel manufacturers. The analyses for ordinary and special elements of all the steels were made on the rod stock as received in the laboratory, and the re-

Jan 1, 1941

By E. P. Humphrey

The Lehigh Valley Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. The Old Breaker This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Coxe, in 1888-89, and was fully described by him in the Transactions1. The columns were cast iron, 8, 10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken down excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water on them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure. The following are analyses of cast-iron, wrought-iron, and structural-steel samples taken from the old and the new structure.

Jan 1, 1918

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By Robert F. Mehl

THE solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstätten figures profusely nor with great ease. A study of the Widmanstätten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstätten figures.1 ALLOYS OF ALUMINUM WITH COPPER The most accurate determination f the solid solubility, of copper in aluminum seems to be that by Dix and Richardson,2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548°, and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solution on cooling tends to precipitate the compound CuAl2, and this conclusion has been confirmed experimentally by Schmid and Wassermann .3

Jan 1, 1932

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By Edward W. Mehal

This paper presents a review of the technologies which have been used in the application of III-V compound semiconductors to integrated circuits and arrays. These materials have properties which make them useful for various devices such as: light emitters, sensors, microwave sources, and microwave diodes. Technologies for incorporating these devices into integrated circuits have been reported and processes developed for fabricating planar devices using selective epitaxial deposition or selective diffusions. Isolation methods utilizing semi-insulating GaAs, oxide isolation, and ceramic insulation have also been reported. These techniques, and the devices and circuits produced or proposed are discussed. AFTER the invention of the silicon-integrated circuit, methods for utilizing compound semiconductors for integrated circuit applications were proposed. The scope of applications was potentially much broader because of the range of properties available from these materials. There also was the opportunity of coupling these properties with germanium and silicon devices to realize functions and circuits which could not be produced with silicon monolithic circuits. Table I exemplifies the range of electrical properties available in III-V compound semiconductor materials which are currently being widely used. A wide range of sensor and emitter applications result from the range of band gap. The band structure of GaAs and GaAsxP1-x permits their use as microwave oscillator source, and the high electron mobilities further facilitate their utility in microwave devices. The concept of "integrated functions"1 results from the availability of these materials and methods for utilizing their special properties. Heteroepitaxial growth allows the fabrication of a monolithic block of these materials. Semi-insulating GaAs permits the attainment of electrical isolation between components in a monolithic block without resorting to p-n junction biasing or oxide isolation methods. An "integrated function" is a unit which can perform a system or subsystem role and perform a number of electromagnetic functions. These functions could include sensor or input transducer, signal processing, interconnections, and control or output function. Two examples which demonstrate this concept are an optoelectric processor and a microwave receiver front end. The optoelectronic processor, Fig. 1(a), would consist of a light sensor, signal processor, and output emitter. The sensor could be InSb or InAs which would be IR-sensitive. The signal from this sensor would then be amplified and transmitted to the light emitter. The amplifier could utilize GaAs bipolar or field effect transistors. A Gap emitter would then produce visible radiation. The microwave receiver front end, Fig. l(b), would consist of a local oscillator section and a mixer section. A signal input from an antenna is mixed with the signal from the local oscillator. The local oscillator signal is produced by a Gunn oscillator. The single-ended mixer utilizes one Schottky barrier mixer diode. The IF signal would then be amplified further and suitably displayed. A further extension of the capability of utilizing the

Jan 1, 1969

By Haim H. Chiswik, Ralph Hultgren

In recent years considerable attention has been devoted to the development of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported' to be of the simple eutectie type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals3 The silver-bismuth diagram is similar.' The solubility of bismuth in silver. has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen6 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,' with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable. Materials and Methods Mallinckrodt precipitated silver, analytical reagent, was used. Maximum impurities listed on the label were: chloride, 0.005 per cent; copper, 0.001; iron, 0.002; other heavy metals (as Pb), 0.002; and sulphate (SO³), 0.05. The lattice constant was found to be a0 = 4.0782 $., in good agreement with the value of Jette and Foote,6 a0 = 4.0779 A., for

Jan 1, 1940

By Ralph Hultgren, Haim H. Chiswik

In recent years considerable attention has been devoted to the development of new commercial uses for silver, chiefly because of lowered prices and large stocks of the metal. This has led to increased interest in the phase diagrams of silver alloys. The silver-lead diagram is reported' to be of the simple eutectie type, but no measurements of the solubility of lead in silver have been made. The solubility of silver in lead has been estimated2 from diffusion experiments and resistance measurements to vary with temperature from 0.09 to 0.18 atomic per cent (0.05 to 0.10 weight per cent). Silver-rich silver-lead alloys have recently been recommended as high-strength bearing metals3 The silver-bismuth diagram is similar.' The solubility of bismuth in silver. has been estimated to be about 5.5 weight per cent on the basis of X-ray work.4 Matthiessen6 found a solubility of silver in bismuth from 0.25 to 0.50 per cent by conductivity measurements. Silver and thallium form the same type of diagram,' with no data on their mutual miscibilities. We have studied the first two of these diagrams by X-ray methods, verifying their main features and determining the solubilities of lead and bismuth in silver at several temperatures. We also determined the solubility of thallium in silver at one temperature. The solubilities of silver in lead and in bismuth were found to be too low to be detectable. Materials and Methods Mallinckrodt precipitated silver, analytical reagent, was used. Maximum impurities listed on the label were: chloride, 0.005 per cent; copper, 0.001; iron, 0.002; other heavy metals (as Pb), 0.002; and sulphate (SO³), 0.05. The lattice constant was found to be a0 = 4.0782 $., in good agreement with the value of Jette and Foote,6 a0 = 4.0779 A., for

Jan 1, 1940

By William M. Bowron

In the hope that a brief description of the conditions that are favorable or unfavorable to success in the practical treatment of titaniferous ores in the blast-furnace may not be without interest to the members of the Institute, the present paper is submitted. The class of ores of which I speak may be described as magnetites, with a gangue of siliceous matter, in which a portion of the silica is replaced by titanic acid. Professor Dana, in his System of Mineralogy, gives a long list of representative analyses of titanic iron ore in which the percentage of titanic acid varies from 59 down to 34. If the percentage is below the latter figure, the ore is no longer recognized as a "titanic ore;" although, according to my experience, titanic acid is present, in small quantities, in almost all ores. In the methods followed in ordinary analysis it is usually included with the "insoluble matter," unless special search is made for it. In the ores usually regarded as "titanic "the proportion of titanic acid frequently assumes quasi definite percentages, such as from 4 to 5, 8 to 9,12 to 13, and so on, in an ascending scale to those higher percentages that do not at present concern us. The proportions quoted characterize large masses of ore that are now accessible to market and are lying idle only on account of the titanic stigma. My experience with titanic acid in the furnace began in England, fourteen years ago, with my being employed as chemist by the manager of the Norwegian Titanic Iron Company, which was at that time smelting, without mixture, ilmenite from Norway in a furnace 16' X 50'. The process, regarded as a process, was a perfect success; but the enormous quantity of fuel required, the small quantity of iron in the ore, and the cost and uncertainty of importation militated seriously against its commercial success, and a few years saw the attempt abandoned. The metallurgy being successful, an at-

Jan 1, 1883

By Thomas M. Plouf

Getting optimal performance from flotation cells can, in many cases, be critical to a project's economic viability. Simple testing procedures can sound early warning signals as well as maintain optimum recoveries from the flotation cycle. The materials required for a simple testing laboratory include: (1) pH meter or pH paper, (2) bottles of reagents used in plant flotation, (3) stop watch, (4) calibrated eye droppers. (5) laboratory flotation machine (1000-g tank, open impeller), (6) froth collection pans, (7) magnifying glass, (8) sizing screen sufficient to retain 10% of the flotation feed coarse fraction, (9) sizing screen for the size particles at which desliming of the plant flotation feed is to take place, and (10) a set of screens covering the complete range of feed particle size.

Jan 4, 1978

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

THE crystallographic mechanism for the austenite-to-martensite transformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite-and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite undergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.-Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about -70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of I mm. or more. Four martensite cystals from four different ingots were prepared in this manner; the largest crystal of this group is illustrated in Fig. I. Back-reflection Lane patterns were obtained from martensite [ ] crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution (±0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to {112} and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By Alden B. Greninger, Alexander R. Troiano

The crystallographic mechanism for the austenite-to-martensite trensformation has been deduced from the results of the following new experimental determinations: (I) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite—and thus the relationship between the martensite lattice and the martensite plate, and (2) the measurement and analysis of the change in positions that a volume of austenite unclergoes when it transforms into a crystal of martensite. For the latter study, a new tool was developed, the stereographic analysis of shear. Lattice relationship.—Thirty-five separate 50-gram melts of an alloy containing about 22 per cent nickel and 0.8 per cent carbon were prepared in a high-vacuum furnace. This alloy is all-austenite at room temperature; grain size was about I cm. Specimens of the alloy were cooled to about — 70°C. to form a few martensite crystals, and suitable specimens were ground and polished on a surface parallel to a single martensite plate, exposing the martensite crystal for an area of 1 mm. or more. Four martensite cystals from four diffierent ingots were prepared in this manner; the largest crystal of this group is illuslratecl in Fig. I. Back-reflection Laue patterns were obtained from martensite crystals (and the matrix austenite) both before and after tempering. The locations of the basal-plane pole of martensite was checked by means of oscillating crystal X-ray patterns. All four crystals studied yielded the same solution ( ± 0.5°), and these relationships are expressed in gnomonic projection in Fig. 3.* The narrow dark-etching bands often visible in martensite "needles" were found to be parallel to (112) and thus are undoubtedly twin bands in the martensite crystal.

Jan 1, 1941

By A. S. Nowick, W. A. Goering

INspite of considerable interest in the kinetics of ordering of the alloy Cu3Au there is no direct information available on the activation energy for atom movements in this alloy, such as that obtainable by radioactive tracer-diffusion studies or by internal friction measurements. Accordingly, this alloy was examined to find out whether it displays an internal friction peak resulting from stress-induced ordering, similar to that studied extensively in other alloy systems.1-3 Measurements of the internal friction as a function of temperature were made in a torsion pendulum similar to that described by Ké.8 Wire specimens 0.032 in. diam and 11 in. long were used. The wire, obtained in the cold-drawn condition,* was annealed at 900C in a quartz tube to obtain a large grained sample, and then mounted in the torsion pendulum furnace. Internal friction is reported here as the lag angle, 4, which is equal to the logarithmic decrement divided by .ir. Fig. 1 shows the internal friction at three frequencies (the frequency given for each curve is the value measured at the peak). The data for these curves were obtained on cooling one specimen from 460C to just above the critical temperature for long-range ordering, which is about 390C for this alloy. In this way, the internal friction is measured under conditions where the alloy is in the disordered condition throughout the run. The curves obtained at frequencies of 2.15 and 1.29 cps show peaks in the range of measurement. The corresponding peak for the 0.78-cps curve is estimated, from the shift of this curve relative to the others, to be located slightly below the critical temperature (at 385C). The fact that the peak can be observed above the critical temperature is good evidence for the belief that it is a stress-induced ordering phenomenon similar to that which is observed in other disordered alloys. The fact that the peaks in Fig. 1 are not the same

Jan 1, 1959

By N. J. Myers, S. J. Nemeth

POWER in the mill at Appalachian Sulphides Inc. is provided by 86 electrical motors ranging from 1 to 200 hp and totaling 1200 hp. After a careful study of different types of support for these cables an expanded metal trough was chosen as the most suitable. One hundred and twenty feet of trough were installed in 18-in. width and 150 ft in 6-in. width. This trough carries all the power as well as the control circuits. Now that the electrical distribution system is complete it is clear that this type of cable supporting system offers many advantages. To handle the same amount of cable in conduit, for example, would have required such a jungle that wiring all the different motors and controls would have been very difficult, even for the original hook-up. In the Appalachian Sulphides operation it has been necessary to make changes from time to time in the wiring of the different motors. These changes are readily made with the present cable supporting system because the trough leaves the wires accessible for rerouting as needed.

Jan 1, 1958

By A. J. Sinclair

Sampling methods for feasibility studies are dependent on geological characteristics of the deposit being evaluated. A preliminary geostatistical study is required, taking into account autocorrelation aspects of variables under study in order that sample plan design can be optimized to produce grade and tonnage estimates within stipulated error limits. In general, regular sample distribution is to be aimed for, and regular sample lengths (from drill core or cuttings, for example) are preferred in order to facilitate statistical analysis. Sample plans are modified and improved (either technically or economically), as a sampling program proceeds and additional information is obtained. Bulk samples for metallurgical testing can be evaluated in terms of the variance shown by all such samples in a deposit and the internal variability of grade. Attention to these sources of variability will ensure proper evaluation of pilot test results from bulk samples. In addition, a general mineralogical study of a deposit is an important, often ignored, requirement in a more general but semi-quantitative evaluation of the representativeness of a bulk sample; and, moreover, provides information useful in optimizing plant design.

Jan 1, 1978

By John F. Burst

GENETIC correlations of the various types of Cheltenham fireclays found in Missouri have been the subject of several papers. The correlations usually have been attempted on the basis of stratigraphic and leaching patterns (Wheeler,18 1896; Allen, 1,2 1935 and 1937; McQueen,13 1943). Herold10 (1943), as well as Allen,l,2 has dealt at length with the mineral¬ogy of Missouri fireclays and postulates genetic relationships from min¬eralogical findings. Both researchers cite kaolinite as the primary clay mineral of the Cheltenham formation and suggest that differences in physical proper¬ties are due to clay mineral impurities such as halloysite or illite (not recog¬nized by the name "illite" at the time of Allen's papers). By ascribing the differences to impurities, it is possible to use weathering as the only major alteration factor. This paper seeks to probe still farther into the clay mineral composition of the Cheltenham formation and to show thereby that the mineralogical differ¬ences that have been found to exist within the "kaolinite" component of the Cheltenham fireclay may alter somewhat the previously held theories of diagenesis. Two Missouri fireclays, which have been rather thoroughly investigated, were chosen for comparison of genetic relationship to clay mineral content. One is a typical plastic fireclay of the middle Cheltenham (McQueen's classification13) obtained at Mexico, Audrian County, Missouri, from a large open pit operated by the A. P. Green Fire Brick Co. The other-a typical hard flint fireclay-was obtained from a pocket deposit in southwestern Mont¬gomery County, Missouri.

Jan 1, 1952

By H. H. Waller, C. H. Brehaut

At the Jeffrey mine of Canadian Johns-Manville Co. in Asbestos, Que., automatic batched concrete from surface is placed underground pneumatically for distances of 2500 ft directly into forms or to a second placer for greater distances, through 6-in. pipe of high carbon steel. The use of Celite C-4-C in addition to the usual aggregates achieves greater compressive strengths, lowers cost, reduces segregation, and improves workability and placeability results. Each year 25,000 cu yd of concrete are placed without interrupting production and development work in the mine, making possible a cheaper concrete that can be poured wherever and whenever it is needed. In about 90 pct of the underground openings in the Jeffrey mine concrete is necessary to preserve them in their original sizes and shapes for production. In the remaining 5 pct, the greater portion is united with or without steel support. When large quantities of concrete were forecast for underground use at the Jeffrey mine, preliminary and first hand information regarding pneumatic placing was acquired from articles by Bernhardt and Swanson and visits to their respective mines.

Apr 1, 1956