Search Documents

By Horace F. Silliman, Curtis L. Wilson, Eugene C. Little

The change in electrical resistance and Rockwell hardness (16-100-B) of copper alloys containing Ni2Si and Co2Si was determined by annealing the quenched solid solutions at various temperatures for various lengths of time. The rate of precipitation of Nisi, as measured by the rate of decrease of electrical resistance and increase of hardness, increased with annealing temperature up to a certain point, depending on the percentage of Ni2Si present. At these temperatures discontinuities in the rate: change occurred. Similar discontinuities in the Co2Si alloys were no The solubility of Co2Si in copper was found to be 5 per cent at 970" DISCUSSION (Robert F. Mehl presiding) R. I?. Mehl, Pittsburgh, Pa. (written discussion).—The electrical conductivity and hardness curves reported in this paper are interesting, particularly because many of the anomalies of the precipitation processes are evident from such curves. The title of the paper, however, is deceptive, for it implies that measurements of electrical conductivity and hardness are suitable to determine the rate of precipitation. Neither of these methods is suitable for a quantitative measurement of rates of reaction or of precipitation in the solid state. Electrical conductivity in some alloys shows an anomalous increase during the first stages of aging at low temperatures; it is notably sensitive to strain and to state of subdivision. I have plotted the conductivity curve representing the decomposition of the phase at 555" C. in the copper-aluminum system, given in the paper by Smith and Lindlief (Fig. 47, p. 93) as a rate of reaction curve, and compared it with the curve determined by area evaluation (Fig. 7); these two curves are not coincident. Hardness is likewise very uncertain, for it is so much dependent upon particle size. Of the various methods proposed for the study of rates of reaction and precipitation, the evaluation of volume of reaction product from the respective area of matrix and reaction product on the photomicrograph is the most trustworthy; suffering, perhaps, only from low sensitivity during the early stages. This method, used originally by Davenport and Bain and now by Smith and Lindlief, is suitable for

Jan 1, 1933

By C. S. Barrett

Measurements of impact hardness of ß-brass are reported for a wide range of temperatures. Abrupt softening is observed when temperatures are raised above 425ºC, accompanied by abrupt widening of deformation bands in the deformed samples. Current theories of these effects, and of the lack of twinning, are discussed. HARDNESS1 and flow stress2 of a sample of ß-brass at room temperature depend upon the temperature from which the sample is quenched. It is believed that the state of order in the superlattice is responsible for this dependence—not the order within individual domains, which reaches near-perfection during the quench from any temperature, but the size of the domains which is presumed to be a minimum in the hardest samples, those quenched from temperatures near the critical disordering temperature of 468°C. Measurements of impact hardness made over a range of temperatures and microstructural studies of samples deformed both rapidly and slowly over a range of temperatures, reported herein, should be of aid in reaching a more complete understanding of the underlying factors controlling the properties of the disordered body-centered-cubic material and the ordered material. It appears that such data have not

Jan 1, 1955

By Roland de Wit

Conclusions reached in a paper by weertmanl are amplified in a mathematical and graphical way. It is shown that in a stressed crystal a straight dis-location may be in a position of unstable equilibrium with respect to helix development, and how a small perturbation may start the dislocation off on its helical path. Helix development occurs by diffision; bulk diffusion is necessary for development from a screw, but core diffision is sufficient for development from an edge dislocation. For a mixed dislocation helix development can take place by core diffusion if the helix also climbs; a diffusion reversal takes place when the slope of the helix equals the slope of the Burgers vector. The work done on a crystal by the external forces is graphically shown to be consistent with the direction of motion of the dislocation in helix development. Finally a detailed mechanism for tangle formation from helices is presented. In the course of helix development a glide situation may be reached where a segment of each helix loop lies in a slip plane in which it can expand by glide. Thus is it visualized how a helix can deteriorate into a tangle. A paper by weertmanl proposes dislocation-tangle formation by a helical dislocation mechanism. The present paper amplifies Weertman's arguments in a mathematical and graphical way and presents some further ramifications of the proposed model. The importance of dislocation tangles is discussed in Weertman's paper and the references cited therein. The mechanism of their formation is not yet understood. Weertman proposes that in cold-worked crystals conditions exist suitable for the conversion of straight dislocations into helices and subsequently into tangles. Helix formation occurs by a diffusion process and Weertman proposes that at low temperatures only core diffusion is important. The present paper necessarily repeats some of Weertman's work. Since the mathematical development and notation used are slightly different from his, this was thought necessary for clarity. GEOMETRY OF THE HELIX weertman2 has shown that the equilibrium form of any dislocation line is a helix if it is assumed that the energy per unit length (line tension) of the dis- location is constant. For the special case that no external forces act on the dislocation, the helix reduces to a straight line. We shall assume in this paper that the dislocation has a helical form even when it is not in equilibrium. The parametric equation of a helix is, see Fig. l: where a is the radius of the cylinder tangent to the helix, and 270 the pitch of the helix. The pitch is related to v, the number of turns per unit length (along the axis) by the relation: When a = 0 Eq. [I] gives a straight line in the z direction. The growth of a straight dislocation into a helix is now described mathematically by letting a vary from zero to its final value. The tangent to the helix is given by where is the path length along the helix. This gives the direction of t and since its magnitude is unity we must have So that dcp/ds = (a2 +p2)-"'. The curvature of the helix is given by where n = -(cos + sin) is a unit vector normal to the helix. Note that the vectors k and n always point toward the axis of the helix, Fig. 1. FORCE ON THE HELIX The external force which makes the straight dis-

Jan 1, 1963

By Walter Larsh

The Ruth orebody, so far developed, is roughly oval in plan, major and minor axes about 1600 ft. (487 m.) and 1200 ft. (365 m.) respectively, average thickness about 120 ft. (36 m.), and with a general dip of about 15° to the northwest. According to the generally accepted theory, the ore is a secondary enrichment of the porphyry due to leaching in situ by meteoric waters. Copper occurs as chalcocite, chalcocite coating pyrite, and a little chalcopyrite. The leached zone, or capping, covering the ore varies in thickness from 110 to 540 ft. (33 to 164 m.), average about 410 ft. (124 m.). The ore is blue gray in color, and the capping, light yellow to brown. Ore was first discovered in quantity in the workings from the Ruth shaft, now caved. Further development work was done by churn drills, and the outline of the orebody, as stated above, determined in this manner. Drilling is still being carried on. The porphyry area is entirely surrounded by sedimentaries, lime-stones and shales; and, in so far as the underground workings have shown, the porphyry' itself, the sedimentaries near the contact, and the country underlying the ore (igneous or sedimentary) is very soft, heavy, and in places swelling ground. All openings have to be carefully and stoutly timbered, and, after once driven, they have to be constantly eased off and repaired. The mine is at present served by two shafts, the Star Pointer, the main working shaft; a vertical, and the Ingersoll, an incline used for waste and material. The two shafts are about 2600 ft. (792 m.) apart, connected on the 500 level; a connection is now being driven on the 600 level. (Dec., 1917. This connection is now completed.) The 300 level, which is finished, and the 400 level which is nearly completed, are accessible only from the Ingersoll and connections with the 500 level.

Jan 1, 1918

By Alexander Anderson

In many oil fields a great variation in the production of adjoining wells has long been observed, and a certain proportion of dry holes, situated between prolific producers, has been regarded as normal without thorough investigation as to cause. Similarly, an occasional prolific producer has been found in a part of a field where all other holes have proven disappointing. Adjoining wells which showed an unreasonable difference in production have been surveyed, and the bottom of the poorest producer has been found to have lost sufficient vertical depth, through its drift, to diminish seriously its penetration in the oil zone. Again, the bottom of the good producer has been found to he more favorably situated by its migration up structure. Surveying of wells in California fields has shown many instances where the dry hole has drifted far off the structure to such a degree that no amount of deepening could ever convert it into an oil well. In other cases, edge wells have been found to drift into the field. At this time, in California, the surveying of oil wells is beginning to he accepted as a routine part of operating procedure. Some operators are surveying all of their new wells and, in some of the recently discovered fields, this practice is providing invaluable assistance in methodical development. The information that has been obtained from the surveying of many wells has convinced most operators that it pays to give careful attention to the drilling of wells. Chews are now usually cautioned to avoid reckless competition with each other. Whereas, formerly, certain companies demanded a large footage from their drillers, they now issue orders that a very moderate speed in drilling shall he maintained and that every care be taken to avoid practices likely to cause excessive deviation of the hole frorn vertical. As a result of these new instructions to drilling crews, a distinct decline in the average drift of the wells drilled by these operators has taken place and fewer dry holes are being drilled from good locations. To the petroleum engineer and the geologist, oil-well surveys provide the necessary data required for the construction of the correct cross-

Jan 1, 1929

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (I) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1938

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division: Generally in Table 1 the unit for presentation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions-—several units of continuous productive reservoirs of distinctly different structure and of distinctly dzerent stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and/or commercial value. As to each space in the tabulation, it is either (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are determinable but not determinable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use 2. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report l,8x,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1937

By D. Turnbull

RECENTLY it has been shown that aggregates of small liquid droplets of tin,' mercury' or gallium' kept from intercommunicating by suitable films do not solidify at an appreciable rate unless the supercooling is very much greater than that usually necessary to cause a large continuous mass of the metal to solidify. For example oxide-coated tin droplets1 (1 to 10 micron diam) must be supercooled 100" to 110°C before their rate of solidification becomes rapid, although large continuous masses of liquid tin usually begin to solidify when supercooled 30" or less." These experiments have been interpreted' on the hypothesis that nucleation of crystals in large continuous metal samples is almost always catalyzed by accidental inclusions. Therefore, if the metal is dispersed into a number of isolated droplets large in comparison with the number of inclusions, most of the droplets should not crystallize until a temperature sufficiently below the thermodynamic melt- ing point, T0, has been reached to permit an ap-preciable rate of homogeneous (noncatalyzed) nu-cleation. In general this temperature is very much less than the temperature at which the rate of heterogeneous (catalyzed) nucleation is appreciable. If this interpretation is correct then investigation of the kinetics of crystallization of small droplet aggregates should be one of the most fruitful methods of obtaining information about the homogeneous formation of crystal nuclei in liquids. In this paper the results obtained on gallium and mercury are reported more fully. In addition, results on the supercooling of aggregates of liquid bismuth and lead droplets are included. Experimental Procedure Some care must be exercised in the choice of a barrier to prevent the liquid droplets from coalescing lest the barrier itself catalyze the formation of crystal nuclei. From this standpoint, the most desirable barrier is vacuum or inert gas, but, because of the difficulty of experimental arrangement, solid compounds and adsorbed films have been selected. There are two guiding principles in the selection of compounds as barriers in addition to the requirement that they prevent coalescence of liquid droplets. First, the compound should be almost insoluble in the liquid metal and second, its lattice structure should be quite unlike that of the forming metal crystal. Even so, there is no a priori assurance that the solid compound film will not catalyze to some extent the formation of metal crystal nuclei. An adsorbed protective monolayer is less likely to be catalytic than a crystal compound film, but it is not often possible to find a monolayer that is stable under the experimental conditions. Also, it is desirable, though not generally essential, that the aggregate of droplets be prepared by breaking up the massive metal rather than from a powdered compound of the metal.

Jan 1, 1951

By I. Cadoff, J. P. Nielsen

The Ti-C phase diagram exhibits a peritectic point at 1750°C and 0.8 pct C, and a peritectoid point at 920°C and 0.48 pct C. The maximum solubility of carbon in a titanium is 0.48 pct. The 6 region containing the Tic compound (20 pct C) extends to 11 pct C at the peritectic temperature. THE interest in the Ti-C alloy system stems from the fact that carbon occurs as an impurity in titanium alloys when graphite electrodes or graphite crucibles are used in their melting. Since titanium-base alloys are still in the development stage, some virtue may be found in carbon addition to titanium. The Tic compound is currently emerging as an important powder metallurgy base constituent similar to the WC compound. Ehrlich' identified the phases and structures present in the Ti-C system. The peritectoid region of the phase diagram was investigated by Jaffee et al." A preliminary diagram based on theoretical considerations was proposed at the outset of this research." The Tic compound has been investigated extensively and has been reported on in a large number of papers. Experimental Procedure Arc-melted alloys of 24 compositions in the range 0 to 20 wt pct C were investigated using metallography, X-ray diffraction, and, for the liquidus and solidus regions, incipient and complete melting. All alloys were prepared from iodide titanium (New Jersey Zinc Co., 99.95 pct Ti minimum) and spectroscopic grade carbon (National Carbon Co.). To prevent carbon spattering during arc melting the carbon was encapsulated in titanium. For alloys containing less than 1 pct C the powder was inserted into a capsule formed by drilling a hole in the as-received rod. For higher compositions, capsules were formed from titanium sheet. Arc Melting: The charges were melted in the copper-hearth cold electrode furnace shown in Fig. 1. This furnace is similar in principle to the all-metal unit adapted for titanium melting at Battelle Memorial Institute.' The transparent pyrex walls giving unlimited visibility during operation and the multiple-

Jan 1, 1954

By George A. Guess

The increasing demand for greater speed and more accuracy, in making daily assays of ores and products from mills treating material containing but very small quantities of lead and copper, has caused the older analytical methods to be supplanted by new ones devised to meet the needs of modern work. For " control" work in copper-analyses, I had, previous to the present equipment, introduced in my laboratory the ordinary electrolytic method, using hollow cylindrical electrodes; and with these I began a series of experiments in determining the lead-content of daily mill-samples and controls. The results, proving accurate and satisfactory, I then devised, with Mr. H. E. T. Haultain, a cheaper electrode than the ordinary jaCket-electrode, which costs from $15 to $20,—the expense of the older form making the installation of many units very costly. The form of cathode finally adopted as the most satisfactory, shown in Fig. 1, is cut from 0.001-in. platinum foil. It is 12.5 cm. long, and is divided into a blade 4 cm. wide and 6.25 cm. long, and a tongue 0.7 cm. aide and 6.25 long, the immersion area being 50 sq. cm. and weight 1.5 grams. The blade is first sand-blasted and then corrugated lengthwise, in order to impart the necessary rigidity. Strips of platinum foil 0.001 in. thick, 12.5 cm. long and 0.5 cm. aide, having a median corrugation, form the anodes. Three electrodes are used in each cell; one anode in the middle and one cathode on each side of the anode. These electrodes are connected to slotted aluminum terminals, in which they are held by contact pressure. The terminals are 5/16in. rods, projecting 2 in. horizontally in front of the wall of the cabinet; at the back the middle electrode (anode) is connected with one pole of the current, and the two outer ones (cathodes) with the other pole.

Jan 1, 1906

By Jerome F. Kuzmick

The use of iron powder during the postwar conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: 1. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price—The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1949

By Jerome F. Kuzmick

INTRODUCTION THE use of iron powder during the post-war conversion period has been increasing with great rapidity. This is particularly true in regard to the manufacture of molded mechanical parts such as bushings, gears, cams, small wheels, and the like. Many manufacturers have found it possible to replace machined cast iron and carbon steel with molded iron powder parts, and thereby can not only effect a savings in cost, but can produce a better product as well. As the field of application for iron powder parts widens, greater demands are made upon the powder supplier concerning quality and uniformity characteristics. The following are some of the most important properties parts fabricators desire in the iron powder they use: I. The powder should have high compressibility so that good density can be obtained without the use of excessive pressures. At the same time, it should show low die wear so that a large number of pieces can be produced from the die. This means that the powder must be of high purity and good softness or plasticity. 2. The powder should produce compacts of high green strength, so that unsintered parts can be handled without breakage or fraying of the edges. 3. The sintering properties should be good so that satisfactory strength is obtained in the sintered piece. 4. Compacts made from the powder should show small but, above all, uniform dimensional changes during the sintering operation so that accurate parts can be produced, and warping and other such bad effects eliminated. 5. The powder should have satisfactory flow properties for automatic molding. 6. It is very important that the powder be uniform in sieve analysis, compressibility, flow, purity, and other qualities, from container to container in any given lot and from shipment to shipment. 7. Price-The fabricators desire all these good properties, but in many instances still do not wish to pay a premium price. There has been considerable discussion as to the importance of price of the powder in relation to the cost of the finished product. It is true that in cases where certain special properties only procured by powder metallurgy are required, price is not a criterion. On the other hand, there have been a number of applications recently made which would not be commercially practical with a powder which commands a premium in price. Iron powder parts are compressed in automatic presses to definite size, shape, and density. The powder is compressed to a density figure dependent upon the function the part is to perform, as well as upon such important considerations as press capacity and die wear. Such parts can be roughly broken down into the following density ranges:

Jan 1, 1948

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

By F. Banemann

In discussing the problem of abnormal magnetic polarization, C. A. Heilandl† emphasized the unfortunate fact that our knowledge of the geological and physical conditions relating to such occurrences is very limited and that a more detailed insight into their physical causes would be extremely valuable for interpreting measured anomalies. He also pointed out that to arrive at quantitative physical formulas that would express the conditions that cause abnormal polarization many more occurrences of the kind would have to be recorded. The first part of this paper is a contribution to such descriptions. Abnormal Magnetic Polarization in South Africa The occurrence was mapped in the course of a magnetometric survey carried out about 70 miles to the east of Johannesburg and east of the Witwatersrand gold field, for the purpose of detecting the position of the suboutcrop of certain magnetite-bearing shales that occur in the lower portion of the Witwatersrand system of sediments, shales whose position in section in relation to the ore-bearing members of the same system of sediments are known. In this case the shales are covered by younger strata several hundred feet thick. Lines of magnetometric traverse were run at right angles to the strike for a strongly magnetic body. This body is a shale zone in the Witwatersrand sediments and has a strike of N.20°E. (magnetic) and dips 15" to the east. The field work was done by a vertical intensity field balance (A. Schmidt principle). The plotting is done in such a way that the sign is reversed from that usually employed in the northern hemisphere, so that a positive profile is obtained in abnormal cases while the same conditions in the northern hemisphere would give a negative one. This method of recording should be kept in mind in reading what follows.

Jan 1, 1940

The amendment to Article III, Section 1, of the Constitution, raising the dues from $10 to $12 a year commencing in 1917, which was submitted to the members for letter ballot, was passed by a vote of 1,039 to 401.

Jan 4, 1916

By R. W. Jigins

OPERATIONS of the Braden Copper Co. are in the Chilean Andes, southeast of Santiago. Most remote of the company communities is Sewell, a town of 12,000 people, 7000 ft above sea level at the junction of the Coya and Teniente rivers. Four miles down the Coya River is the smelter town of Caletones, elevation 4500 ft, with a population of about 3000. At the junction of the Coya and Cacha-poal rivers 24 miles below Sewell is Coya, elevation 2500 ft, location of the company's two hydroelectric plants. The principal accounting offices; steel, iron, and brass foundries; railroad shops; and major mechanical repair and fabricating shops are at Rancagua in the central Chilean valley, 44 miles from Sewell. The company owned narrow-gage railroad connects with the Chilean national railroad at Rancagua and above Coya is the only modern means of travel. El Teniente mine at Sewell is the largest underground copper mine in the world. The mill, at the portal of the main tunnel, has a capacity of 34,000 tons of crude ore daily, although production is lower during the winter beacause of electric power restrictions. When operating at capacity the mill produces 2000 tpd of copper concentrates and 32,000 tpd of tailings. Tonnage of tailings is equivalent to about 100,000 tons of pulp at normal water to solid ratio. Because the streams flowing from the Andes in the area of Braden's operations are used for irrigation, it is impossible to dump tailings directly to the river. The tailings pulp must be separated into solids and decanted clear water, and the clear water returned to the same water shed from which the original water was removed. Remaining sands and slime must be deposited in a reservoir where they will not cause trouble to farmers.

Jan 1, 1958

By Walter R. Crane

Operators of diamond drills have long been familiar with threadlike markings or riflings on cores but apparently have given but little serious thought to the conditions that are responsible for their production. The opinion generally held by those who have observed the phenomena is that the riflings are produced directly or indirectly by vibration, but so far as the writer is aware no systematic attempt has been made to demonstrate the fact. A careful search through the literature on diamond-drilling practice has been rewarded by only one reference to such markings of cores. J. N. Justice1 writes, "Of the peculiarities met with in the core, I will mention only one. The core from the "H" drill, at about 360 ft. came out rifled and pentagonal. The change from the circular to the pentagonal was sudden, and for 9 ft. this structure was maintained, when suddenly it returned to the circular. I have not been able to find any one who can explain the cause of this change of form. The drill men marveled at it and suggested vibration, six-stone bits, and several other hypotheses which need not be mentioned." The writer became interested in the matter of core riflings some 10 years ago while in the Flat River lead region of Missouri, where many remarkable examples of "rifled" cores were observed and collected. Since that time similar phenomena have been observed in various localities throughout the United States and Canada, and samples have been gotten together illustrating a large number of variations in form. After a careful study had been made of the material at hand it seemed desirable that certain data should be obtained from the experience of others regarding the normal action of diamond drills in forming cores, portions of which are occasionally rifled, before an attempt was made to draw any conclusions as to their cause. About 20 letters were addressed to diamond-drill companies, operators, and engineers actively engaged in drilling operations, with a

Jan 1, 1917

By Richard S. McCaffery

A Research on iron blast-furnace slags has been in progress since 1922 in the metallurgical department of the University of Wisconsin, supplemented by observations, tests and critical examination of operating records at 10 furnaces. From the data thus collected information has been put into forms suitable for use by furnace operators and is given in this report and the three accompanying papers.' In the viscosity results reported, it is estimated that temperatures were measured within 5" C. and that the viscosity determination of the particular slag investigated is accurate within ± 4 per cent. In the viscosity diagrams in the various papers, the equal viscosity lines were drawn in such a manner that in all cases they are located correctly with respect to the actual experimental results, but when determining a viscosity for a particular composition from the diagrams, the viscosity may. be slightly less accurate than the experimentally determined viscosity for the same slag, for the reason that the iso-vis lines interpolated between the experimental results may be shifted slightly without violation of the experimental data. The viscosity diagrams represent our judgment of their position under the above conditions, and we believe the relative accuracy of viscosity data taken from the diagrams is more than sufficient for any use to which the data may be put. Hundreds of samples of slags synthetically produced in the laboratory and of actual furnace slags have been studied in various ways. The ranges of compositions of slags used for viscosity measurements are: silica 25 to 55 per cent.; alumina 0 to 35 per cent.; lime 25 to 55 per cent.; magnesia 0 to 20 per cent. These measurements were made at temperatures of 1250°, 1300°, 1350°, 1400°, 1450°, 1500°, 1550°, 1600" and 1650" Centigrade. Descriptions of apparatus, methods used and statements of the problems investigated have been published in the papers listed in the bibliography beginning on page 120.

Jan 1, 1932

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

By B. S. Butler

Apropos of metals low in the series illustrated by Dr. Butler's Table 11, it is interesting to note that Cress and Feldman29 reported traces of platinum metals in several samples of alunite. They found, chemically and spectrographically, several traces of platinum, palladium, and rhodium in alunite from Sugar Loaf Peak, near Quartzite, Ariz.; silver, platinum, and rhodium in alunite from Rio Grande County, Colorado; and traces of rubidium and gallium in various samples of alunite. These authors stated that the platinum metals appear to be present as Oxides and suggested deposition by hydrothermal solutions under near-surface conditions. AS described by Heineman,30 the wall rock of the Sugar Loaf alunite veins shows considerable alunitic alteration. Pyrite and hematite are relatively abundant in the wall rock but decrease progressively near the veins. Assays of samples of the Sugar Loaf alunite, run by J. B. Cunningham of the University of Arizona College of Mines, showed traces of silver and 0.002 to 0.004 oz of gold per ton, but the chemical form of the gold and silver in this occurrence remains undetermined.

Jan 1, 1957