Search Documents

By L. D. Jaffe Hollomon, Hollomon John H.

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By Hollomon John H., L. D. Jaffe Hollomon

For many steel parts it is desired to obtain the maximum toughness consistent with the strength required by the mechanical design. It is generally recognized that the greatest toughness at any given strength is found in steels having a tempered martensitic structure.' and is virtually independent of the composition of the steel2 (except for carbon). The choice of the composition of a steel for the parts in question should be based, therefore, on hardenability considerations and on manufacturing facility and economy. In a recent paper3 the concept of hardenability was discussed and a somewhat new approach to the problem was suggested. The hardenability was defined in terms of the cooling conditions (speed of cooling) required to avoid the pearlite and the bainite reactions. Since all the alloying elements do not have the same effects on the two reactions, the bainitic and pearl-itic hardenabilities must be considered separately. In order to design a steel for a given part, it is necessary to design a composition that has both sufficient pearlitic and sufficient bainitic hardenability. However, this requirement does not fix the combination of alloying elements to be used; an infinite number of steels would have the required hardenabilities. Other considerations limit the choice. For example, decreasing the carbon content increases the toughness at a given hardness, and for this reason low-carbon steels are often desired. Limitations or requirements of refining, casting, or forming practices often affect the level of some of the alloying elements. Price considerations enter. Frequently, however, it is very desirable to minimize the tendency toward quench-cracking while maintaining the necessary hardenability. This paper is concerned with suggesting a method for choosing compositions that will have the required hardenability together with minimum tendency toward quench-cracking. Quench Cracking Since only the case in which the entire part will transform to martensite in the particular quench employed is being considered, the analysis of the quench-cracking problem is somewhat simplified. Quench-cracking arises from the temperature gradients existing throughout the piece during cooling. Because of these temperature gradients, the contraction arising from the decreasing temperature and the expansion arising from the austenite-martensite reaction do not occur uniformly over the parts, and stresses are set up that tend to cause cracking. The temperature gradients can be reduced by decreasing the severity of quench. This, however, requires that the hardenability be correspondingly increased by increasing the carbon or alloy content. An

Jan 1, 1947

By Waldemar Lindgren

THE important investigations of Dr. G. F. Becker at Steamboat Springs, Nev., in 1885, aided by the analytical work of W. H. Melville, established the fact that sulphides were being deposited at the surface by hot ascending waters.1 Steamboat Springs is situated near the eastern base of the escarpment of the Sierra Nevada, six miles distant from the Comstock lode. In a region of former volcanic activity, hot springs with a temperature of about 80° C. break forth through a fissure in granodiorite, and at the base of a basaltic bluff the waters have deposited a large amount of siliceous and calcareous sinter, some of which is colored red by antimony sulphide. The sinter from one of the springs was analyzed by Mr. Melville,2 and his results, re-calculated to grams per kilogram, showed [ ] The relative quantities of antimonious and arsenious sulphides are not given in the above analysis, but I believe that the former greatly predominated. The water of one of the springs was also analyzed by Melville and the re-calculation of this analysis to salts that were possibly present is given in Table I.

Jan 1, 1913

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

THE Joint Committee appointed to consider a Code of Ethics for Engineers recommends, after delib-erate consideration, that each participating Insti-tute or Society adopt the short simple Code of Ethics following this report. The Committee further recommends that the following method of interpreting and administering the Code be adopted by each participating Institute or Society after any necessary provisions have been, made in the Constitution and By-laws of the Organization. The President of each Society or Institute shall appoint a Standing Committee on Professional. Conduct, to administer the Code of Ethics. The duties of such a Committee shall be to interpret the Code and to render opinions on any cases of ques-tionable conduct on the part of members that may be submitted to the Committee. These interpretations shall be reported to the Executive Board of the Institute or Society who may approve these interpretations, or take such other action as may seem just and necessary. The reports of the Committee on Professional Conduct, when approved by the Executive Board, shall be printed in abstract and in anonymous form in the Institute's or Society's monthly journal for the instruction and guidance of fellow members. This Committee on Professional Conduct shall be appointed in each Institute or Society by the President holding office at the time of the adoption of this Code and shall consist of five member one appointed for five years, one for four years, a third for three years, a fourth for two years and a fifth member for one year only. Thereafter, the President then holding office shall appoint one member annually to serve for five years, and shall also fill any vacancies that may occur for the unexpired term of the member who has withdrawn. These appointments shall he made from among the older members of the Institute or. Society, so that advantage may be taken of their mature experi-ence and judgment. The Committee after appointment shall elect its own chairman and secretary. The Committee shall have power to secure evidence or other information in any particular case not only from the organization's own members, but if it should seem desirable, from men in other professions. The Committee may also appoint sub-committees to consider certain cases when deemed necessary.

Jan 3, 1922

By Woo-Zin Choi, Ting Chuen Pong, Roe-Hoan Yoon, James R. Craig, Robert M. Haralick

Detailed analysis by conventional techniques and by the General Image Processing System (GIPSY) has revealed that the conmunution of base metal-containing, complex, fine-grained sulfide ores results in the selective concentration of some ore minerals as a function of size fraction. The ores studied are massive, metamorphically recrystallized, pyrrhotite-rich masses with 10-30 percent pyrite and several percent each of sphalerite, chalcopyrite, and magnetite; gangue minerals - amphibole, mica, and quartz - constitute approximately 10 percent of the ore mass. Examination of samples from laboratory grinding experiments, - from +35 to -250 mesh - produced by both Impact and attrition grinding, reveals that there are significant differences in the mineralogical content of the various size fractions. No single fraction is representative of the bulk mineralogy of the sample. Pyrite is highly enriched in coarser fractions, whereas chalcopyrite, sphalerite, magnetite, and gangue minerals are concentrated in the finer size fractions. Concentration of the ore minerals in the finer fractions is attributed to their common presence as interstitial, grains along the grain boundaries of the more dominant pyrrhotite and pyrite. As such, they tend to be somewhat preferentially liberated as small fragments during the initial stages of crushing and grinding. The relatively coarse-grained pyrite, up to 1 cm cubes, is brittle and readily fractures into coarse fragments which are seen in larger size fractions.

Jan 1, 1984

By J. H. Moran, E. E. Finklea

The pressure build-up technique is a recognized method of determining permeability from conventional drillstem tests. In this paper an effort is made to extend such techniques to the interpretation of data obtained from the wireline formation tester. Such a study is necessary because of the differences, for this case, in the magnitude of the flow parameters (rate of flow, amount of recovered fluids) and in the flow geometry (flow through a perforation vs flow across the face of the wellbore, etc.) involved in the solution of the equations of flow for compressible fluids. The perforation is replaced by a spherical hole, and the effect of the borehole is neglected, so that the flow can be considered to be radial in a spherical co-ordinate system. Arguments are presented to justify this idealization. Assuming single-phase flow, general relations between pressure and flow rate are developed for a homogeneous medium. The study is then extended to permeable beds of finite thickness. It is shown that the early stages of pressure build-up tend towards spherical flow, while the later stages tend towards cylindrical flow. The thinner the bed, the more quickly flow approaches the cylindrical model. The prevalence of thin beds in practical work makes this analysis quite important. Cases involving permeability anisotropy are treated. INTRODUCTION From wireline formation tester operation, two types of data are obtained: (1) the nature and amount of recovered fluids, and (2) the pressure history recorded during the test. A number of papers have been written dealing with the interpretation of formation production on the basis of the recovered fluids.'.' In general, the methods described have been quite accurate for both high- and low-permeability formations. The present paper will deal with an analysis of the pressures observed. An analysis of the pressure build-up curves obtained in hard-rock country has already been attempted on the basis of the formula proposed by Hor-ner. Although this approach has met with success in many instances, some questions have been raised as to its validity. It is the aim of the present study to place the analysis of pressure build-up in the formation tester on a firmer basis, from which more detailed methods of interpretation can evolve. Because of the great differences between the operation of the wireline formation tester and the conventional drillstem test, modifications are necessary in the interpretation. The major difference relates to the flow geometry. Once the flow geometry has been established other features such as multiphase flow, skin effect, afterflow, etc., well described in the literature, can be introduced. It will be assumed that the mechanical operation of the formation tester is already known to the reader.6 t will suffice here merely to state that the tester provides the means for taking a relatively small sample of the fluid immediately adjacent to the borehole, and for recording the subsequent pressure response. In comparison with conventional drillstem tests, the time required for a satisfactory pressure build-up response is much shorter, because of the relatively small quantity of fluid withdrawn by the wireline tester. This feature is highly desirable in the case of low-permeability formations. For an analysis of the pressure response within the formation, three simple flow geometries are considered— linear, cylindrical and spherical. The spherical and cylindrical flow geometries are most pertinent to the formation tester; therefore, they will receive the major emphasis. Since the configuration of the borehole and the perforation made by the tester complicate the flow geometry, it is necessary to allow for them in the drawdown response. However, because of the volume of formations contributing to the pressure-response, the details of the perforation shape are unimportant in the build-up period. Since relatively small amounts of fluid are withdrawn from the formation, in contrast to a conventional drill-stem test, a study of the "depth of investigation" and the significance of drawdown as well as build-up data will be included. Because the "depth of investigation" will be shown to be rather large, the effect on the build-up curves of the finite thickness of the permeable bed is considered. It is this consideration that leads to the importance of cylindrical flow geometry. Also included is a discussion of permeability anisotropy and its effect on the interpretation of the tester results. The pressure curves recorded by the formation tester will follow two general patterns, depending upon whether the formation is of high or low permeability. Fig. I (a and b) schematically illustrates these two responses. In Fig. 1(a), the high pressure recorded during fill-up of the tool is essentially the pressure differential across the choke in the system. In Fig. l(b), the flow rate is

By T. G. Madgwick, A. Beeby Thompson

FoR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippere and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world's supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure important commercial communication with the outside world through the medium of the Black Sea. The first tank steamer was successfully launched on the Caspian in 1879, by Messrs. Nobels, for transporting oil in bulk instead of in barrels. In 1905, an 8-in. pipe line to Batoum was completed; this was capable of transporting to seaboard 8,000,000 bbl. of kerosene per annum.

Jan 1, 1921

For the convenience of members who may be traveling from place to place, the Secretary has compiled a list of libraries or other places in the United States and foreign countries where MINING AND METALLURWGY or the Transactions may be consulted. This list will be sent to members if they so request.

Jan 1, 1925

By J. W. Miller

One of the major problems confronting coal producers in this highly competitive era is whether or not the potential profit to be made from the products of coal flotation would warrant the capital investment required for the necessary equipment. The author supplies two theoretical cases to illustrate methods for computing such costs.

Jan 3, 1961

By Charles R. Austiuon, Carll H. Samans

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Carll H. Samans, Charles R. Austiuon

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Kenneth R. Hancock

Iron oxides are unique in that they are the only significant colored mineral found in a natural state suitable for use as a pigment after it has been pulverized to pigmentary size. The current world production of iron oxide pig¬ments is estimated by the author to be between 450,000 and 550,000 tons based on 1969 data. The fact that highly colored natural deposits of iron ore are found throughout the world ac¬counts for its use in prehistoric man's artistic cave paintings. These early artists did not realize that they had established man's first paint test fence which now has some 20,000 years of exposure. In addition to abundance, constituting about 7 % of the earth's crust, iron oxides have the advantages of low cost, permanency, and are not toxic. Through the centuries, succeeding civilizations have utilized iron oxides as a major source for decoration and protection when coloring was desired. In the last century the chemical industry has improved on nature by developing a complete range of synthetic iron oxide pigments which surpass the pigments pro¬duced from natural iron ores in uniformity, color quality, and chemical purity. In the United States alone, the combined production of natural and synthetic iron oxides produced sales of over $28,000,000 in 1970 (Stipp, 1970). Nomenclature With the increasing importance of the syn¬thetic iron oxides it is necessary to make a distinction between the natural or mineral pig¬ments and the synthetic pigments. Natural pigments are those products which are derived from selected ores and should not be confused with iron ores mined for steel production. Iron ores that are mined for steel must be capable of being mined and reduced to iron on a com¬mercial basis. These ores are selected on the basis of iron content and processing economics. It is therefore unusual when iron ores for steel production are suitable for use as mineral pig¬ments. Natural pigment ore sources are se¬lected for their special physical-chemical prop¬erties and can command a premium price. Synthetic pigments, and in this instance iron oxides, are those pigments produced from basic chemicals. Through chemical synthesis pig¬mentary sized particles are produced as opposed to comminution, the major procedure common to all natural iron oxide pigments.

Jan 1, 1975

By D. Walton, W. C. Winegard, W. A. Tiller, J. W. Rutter

It is shown that the cellular substructure observed in binary alloy crystals grown from a melt of known concentration can be eliminated by the proper choice of growth conditions. For a given solute concentration, there exists a critical ratio of temperature gradient G in the melt to the rate of solidification R of the crystal, i.e., of G/R, which must be exceeded before the cellular structure can be eliminated. A secondary substructure is observed which is related to the cellular substructure. IN crystals grown from the melt, a prismatic substructure has been observed by Buerger,1 Pond and Kessler,2 and Rutter and Chalmers." This structure is columnar in the direction of growth and appears as a network of hexagonal cells in the plane of the solid-liquid interface. Rutter and Chalmers3 have shown that this substructure occurs as a result of the presence of a layer of high impurity concentration in the melt adjacent to the solid-liquid interface. The formation of the substructure is accompanied by a redistribution of this impurity in the neighborhood of the interface. The structure can be controlled by proper adjustment of the variables in the solidification process such as a rate of solidification and the temperature gradient in the liquid. The redistribution of solute during the solidification of metal crystals has been treated theoretically

Jan 1, 1956

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By G. B. Gould

EVERY mathematical statement of a measure of anything (as distin-guished from a count) is followed by a qualification always implied if not explicity stated--that the statement is only an estimate, which may vary from absolute accuracy within certain limits, according to the accu-racy of the measuring instrument. This basic fact, so obvious to engineers, is not so well understood by many that make use of laboratory coal tests. The tolerances that must be allowed in measurements of coal quality are very important in both their commercial and engineering applica-tions-and the significance of these tolerances depends upon the use made of the laboratory coal test. Only in recent years has there been any intensive study of this ques-tion of tolerances as applied to measurements of coal quality. There is very little in our published literature on the subject, and what has been published is not, readily comprehended by those who sell coal, or buy coal and use it, unless they happen to have made a study of the subject them-selves. There is great need for more widespread understanding of what has been discovered and how it applies to the use of laboratory coal tests. What follows is an attempt to condense into a few pages the results of the major investigations so far reported, and to explain their meaning in simple nontechnical language, with the addition of some recent illustrative experiments.

Jan 1, 1937

By J. H. Keeler

QUESTIONS raised during earlier investigations of the preferred orientation in titanium1 and zirco-nium sheet led to the examination of the rolling and annealing textures of beryllium and hafnium sheet. Since the c/a ratios are 1.568 and 1.584, less than that of ideal close packing, 1.633, it would be expected that the preferred orientations would be similar to those exhibited by zirconium and titanium. This was found to be true. However, in several regards the orientations observed for beryllium differed from those reported by Smigels-kas and Barrett4 and so are given here. The okientations for hafnium are presented since only the cold-rolling texture has been reported in the unclassified literature. The pole figures were determined by transmission using an X-ray spectrogoniometer with copper Ka radiation and the automatic pole-figure recorder designed by Geisler described previously.6 The intensity units in the pole figures in this case are only arbitrary since calibration against a random sample of the same material was not considered necessary for the original purpose of the examination. The beryllium sheet, cold-rolled from 0.036 in. to 0.006 in., a reduction of about 84 pct, exhibited a split texture with the [1010] direction in the rolling direction as shown in Fig. 1. The same specimen annealed in vacuo for 1 hr at 1000°C showed no change in orientation. These textures

Jan 1, 1959

By J. A. Kitchener, J. P. Anfruns

Measurements have been made of the rate of capture of single particles of strongly hydrophobic, surface-methylated, quartz, of sizes ranging from 12 to 40 µm diam., by single rising bubbles of diam. 0.5 to 1.1mm. The results agree closely with the theoretically calculated hydrodynamic collision rates, indicating that, in this system, every collision results in capture and retention of a particle.

Jan 1, 1976

By J. D. Livingston

THE hardening of alloys by the precipitation of a second phase has long been an important technological process. One approach towards improving our understanding of this phenomenon has been a correlation of mechanical properties with such parameters as particle size and inter par ticle spacing.' Several reviews of such data have appeared.2-4 A major limitation to this approach has been that for most alloys the particles are submicroscopic in size in the range of optimum hardness. Precipitation-hardening copper-cobalt alloys, therefore, are of interest, because the ferromagnetic properties of the precipitate make it possible to measure particle size, number of particles, and so forth, from magnetic measurements alone.5, 6 Livingston and Becker7 have applied these techniques to a study of precipitation hardening in an alloy of 2 pct Co in copper. It was found from magnetic measurements that nearly all the cobalt to be precipitated was out of solution within a few minutes at 600°C, whereas the peak in tensile yield stress was not attained until a much longer aging time. Thus during the first 1000 min of aging time at 600°C the Yield stress was increasing while a constant volume of precipitate was coarsening, i.e., while particle size and interparticle spacing were increasing. Peak yield stress was reached at an average particle radius of about 70A. The earlier study was confined to one alloy at one aging temperature, so that the volume fraction of precipitate was fixed and, therefore, particle size and interparticle spacing could not be independently varied. The work has now been extended to several alloys of varying percentage cobalt in copper, and to aging at various temperatures. It was hoped that such a study might clarify the relative importance to precipitation hardening of particle size, interparticle spacing, and volume fraction of precipitate. EXPERIMENT The alloys studied contained 0.7, 1.3, 2.0, and 3.2 wt pct Co in copper. They were prepared from electrolytic copper and electrolytic cobalt in a vacuum -induction furnace, worked to 3/8-in.-diam rod, and machined into tensile specimens with a gage section 1 1/2 in. long and 3/16 in. in diam. All specimens were given a solution treatment consisting of a 30-min anneal in nitrogen at 1000° C followed by a quench into iced brine. Subsequent aging was done in nitrogen and followed by a water quench. Average grain diameter was approximately 0.01 in.

Jan 1, 1960

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sand-blasting agent, as a premium grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is produced by E. I. du Pont de Nemours & Co. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about one-fifth of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. This process yields staurolite concentrates of the characteristics given in Table 1. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required [ ]

Jan 1, 1983