Search Documents

By M. S. Abrahams

Germanium has been rolled in the temperature range of 700o to 800°C. The thickness has been decreased by as much as a factor of four, from a thickness of 0.032 in. to a thickness of 0.008 in. For deformations below 60 pet, the true strain per pass is found to be a constant; from the temperature dependence of this slope, an activation energy of about 2.5 ev is obtained. This energy agrees with that for dislocation climb in germanium . For reductions greater than 60 pet, complete rings are seen in the Lave photographs, new grains are observed in the microstructure, considerable softening occurs, and the hole mobility is very low. This evidence indicates that the recrystallization of gertnanium has occurred. GERMANIUM has been deformed in many ways1 including tension, compression, torsion, and bending since Gallagher2 first described its plastic nature at elevated temperatures. All of these studies indicate that the glide plane in germanium is (111) and that the glide direction is (110). Rolled germanium specimens were used by Kolm, Warekois, and Kulin3 in their X-ray study of deformed semiconductors, but no information is given on the rolling itself. The present experiments deal with the rolling of germanium at various temperatures and for different orientations. In all previous deformation studies, the phenomenon of recrystallization (i.e., the transformation of a single crystal into a polycrystal) in germanium has not been observed4 despite relatively large deformations at elevated temperatures. The proposed reason4 for this was that sufficient energy could not be stored in the deformed germanium lattice. In contrast to the earlier studies this work will present evidence indicating that recrystallization occurs in germanium during rolling at an elevated temperature. I) EXPERIMENTAL PROCEDURE A) Test Specimens. The samples used for rolling were in the form of rectangular parallelepipeds measuring 0.3 in. long, 0.06 in. wide, and 0.035 in. high. They were cut from an undoped single-crystal ingot of p-type germanium with a resistivity of 24.4 ohm-cm, a Hall mobility of 2300 sq cm v-' sec-l, and a hole concentration of 1.1 x 1014 cm"3 at room temperature. The surfaces of the specimens were metallographically polished prior to rolling. The initial dislocation density of the samples was about 10' cm-' as determined by etching in CP4. Two different specimen orientations were used. In the first case, the direction of rolling was parallel to (251), the surfaces in contact with the rolls were of the form (1021, and the normal to the third face was parallel to (211). The corresponding di-

Jan 1, 1964

By Morris Cohen, Robert C. Ruhl

Fe-Ni-B alloys were inresligated by X-ray diffraclion after splat quenching. Although this rapid cooling did not produce a measurable supersaturation of dissol1ed boron in either binary Fe-B or Ni-B alloys, a marked increase in dissolved boron was achieved by the splal quenching of lernary Fe-Ni-B alloys. Boron additions up to 2.0 wl pcl to Fe-13Ni and Fe-24Ni alloys cause an increase in retained austenite from 0 to 59 pet and to 92 pet, respectively. The martensitic phase in the Fe-13Ni-9 at. pct B alloy is .found to conlain about 0.6 at. pet interstitial boron, as evidenced by the tetragonality of this phase, and about 3.6 at. pct substilutional boron, us deduced from the lattice paratrieler decrease, the balance of the boron being precipitated as (Fe,Ni)aR. The austenitic Fe-Ni-B plznses also contain both interstitial and substitutional boron. Iron-Boron System. The phase diagram and related information about the solid solutions and intermediate phases in the Fe-B system are given by ansen,' Elliott.2 and Pearson.1 The equilibrium solid solubility of boron in both ferrite and austenite is quite small: the maximum solid solubility of 0.02 wt pct B (0.11 at. pct B) occurs in iron at the eutectic temperature of 1150°C. while the maximum solubility in a iron is less than 0.01 wt pct.l There is disagreement in the literature as to whether these solid solutions are substitutional or interstitial. Based on the measured activation energy of boron diffusion in iron, it appears likely that boron moves interstitially in austenite. 4 However, this observation does not rule out the possibility that some of the dissolved boron may also occupy substitutional sites in this phase. Investigations of internal friction of boron in iron have suggested that boron is interstitial there.' Shevelev, 5 on the other hand, reports a decrease in the ferrite lattice parameter with dissolved boron content, thus indicating a substitutional solution. Unfortunately. Shevelev's methods and analysis are unclear. Goldhoff and spretnak6 have measured the lattice parameters of pure iron and an Fe-0.005 wt pct B (0.027 at. pct) alloy at both room temperature (ferrite) and from 920° to 1200°C (austenite). They reporte: a lattice contraction in the ferrite of 0.0003 ± 0.0002 due to boron, thus indicating a predominately substitutional solution. Appreciable (0.0010 to 0.0060) lattice contractions were found in boron-containing austenites, but these effects were much larger than could be accounted for by the substitutional solution of all the boron present. Nickel-Boron System. Elliott 2 gives a summary of thephase diagram and recent work on this system. The solubility of boron in nickel reaches a maximum of 0.03 wt pct at the eutectic temperature of 1080°C. Iron-Nickel System. ansen' presents the equilibrium diagram for this system and also discusses the metastable austenitic and martensitic phases along with the a=? transformations. The lattice parameters of Fe-Ni ferrites have been recently redetermined by Abrahamson and Lopata.7 Their data, Fig. 1, show an unusual change in slope at about 1.7 at. pct Ni. Very few measurements of the lattice parameters of Fe-Ni martensites are available in the literature. The values of Roberts and Owen8 are considerably higher than those measured in the course of the present work: they find that a, is constant at 2.874? from 8 to 30 at. pct Ni. Both the slope change in the ferrite parameters and the occurrence of a maximum plateau in the marten-sitic lattice parameters vs composition denote the

Jan 1, 1970

By R. W. Shearman, F. Weston Starratt

A new center for mining and metallurgical research is developing at Sterling Forest, N. Y., under the auspices of Union Carbide Corp. Here is to be located the Union Carbide Nuclear and Ore Research Laboratories. In truth, history has repeated itself; the Sterling Forest area in the days of the Revolutionary War, and for many years thereafter, was the mining and metallurgical center of the US. For in these Ramapo hills along the New York-New Jersey border, iron ore was mined, pig lion was cast, and the weapons of war and the plowshares of peace were forged. Before embarking on an historical pilgrimage to yesteryear-a brief description of Sterling Forest. Located in Orange County, N. Y., near Tuxedo, immediately north of the New York-New Jersey State line, and just west of the Erie Railroad and the New York State Thruway, Sterling Forest is approximately 35 mi from New York City. Title was acquired in 1956 from the Harriman family by City Investing Co. Its President, Robert W. Dowling, has established himself as a city planner, having conceived such projects as Pittsburgh's Gateway Center and Philadelphia's Penn Center. A unique, self-contained community -is planned that will contain light industry and centers for research and engineering. Colonies of homes will be interspersed throughout the 20,000 acres of forest land, lakes, and rolling hills. Culture will not be neglected, for Sterling Forest will be the new home for the annual Empire State Music Festival The Sterling Forest Gardens, 125 acres of landscaped woodland and streams, will become the "world's largest permanent floral showplace" The Sterling Forest International Research Building was opened earlier this year, and designed to provide all facilities needed by small growth research companies. The first major company to acquire land to construct research buildings at Sterling Forest is Union Carbide. 1763 ... Discovery of iron ore In turning back the pages of history, a fascinating story can be told of special interest to the metallurgist, the mining engineer, and perhaps even the sociologist. For, where new communities are planned today, older communities had been born, matured, and died. In these hills had lived the. iron miners, the blacksmiths, the lumbermen, the masons, and the teamsters that had given America its start in heavy industry. This was the area where the forests were crisscrossed with many wood roads that brought logs to the charcoal pits, and iron ore to the furnaces. Men make history. Our story brings forth many names of men known as ironmasters, or as industrial leaders-Hasenclever, Faesch, Erskine, Townsend, Ryerson, Parrott, Cooper, Hewitt, Jay Cooke, and Harriman. The name Sterling is derived from a Scotch Lord, the Fifth Earl of Stirling (in its earlier spelling). Lord Stirling was one of seven Englishmen granted a patent of land in the Ramapo hills by Queen Anne in 1707, known as the Cheesecock Patent. He sent an agent, Cornelius Board, to America in 1730, with the express purpose of looking for copper deposits. While he found no copper in his travels up and down the Ramapo Valley, he did find iron ore in two localities: first, in the vicinity of what is now Ringwood, N. J.; second, five miles to the north. There he constructed a forge and furnace at the edge of a lake in 1736, naming the land Stirling Property, after his patron. In 1740, the Ogden family in Newark bought land from Board at Ringwood and began smelting of iron in 1741. The Ringwood story Soon, a genius in the person of Peter Hasenclever appeared on the scene. He was attracted by an advertisement in the New York Mercury for March 5, 1764, in which David Ogden of Newark offered

Jan 1, 1961

By W. B. Potter

THERE is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

Jan 1, 1877

By Richard H. Rein, John Chipman

Liquid slags of the system SiO2-Ca0-MgO-A1~03 were equilibrated with liquid Fe-Si-C alloys in graphite or Sic crucibles at 1600°C in pure CO gas at atmospheric pressure, and the silicon content of both phases determined. Ternary slugs of the systern SiO2-CaO-A12O3 were also studied at 1550°C. The silicon content of the metal phase saturated with both graphite and SIC is 22.0pct at 1550°C and In the iron blast furnace, as in nearly all carbon-reduction processes, some silicon is transferred from slag to metal. The importance of this reaction is enhanced by its indirect effect on the transfer of sulfur from metal to slag, and this has stimulated a comprehensive research program on the equilibrium distribution of silicon between slag and metal. Earlier studies'-3 of this same problem provided data for calculation of the thermodynamic activities4 of the components in SiO,-CaO-A1,O3 slags. 22.4 pct at 1600°C. The temperature at which the phases cristobalite, gvaphite, $ SiC, liquid slag, Fe-Si-C alloy, and CO gas at 1 atm pressure can coexist in equilibrium was found to be 1533°C. The results agree well with earlier studies. They are shown graphically as lines of constant silicon cmtent in the metal which also are lines of constant SiO, activity in the slag.

Jan 1, 1963

By Arthur Flagg

(New York Meeting, February, 1913.) THE Elk City mining district of Idaho occupies a position near the geographical center of Idaho county, a region of mod¬erate elevation in the western foot-hills of the Bitter Root mountains. The district comprises an area of approximately 350 sq. miles, bounded oil the west by the Newsome district and on the south by the Dixie and Oro Grande districts. There are no mining districts to the north or east. Elk City, the principal town and the seat of the mining office for the district, is situated in a hydrographical basin surrounded by low hills. The elevation is 4,200 ft. above sear level. Through this basin flow Elk Creek, Red river, and American river, which unite west of town to form the south fork of the Clearwater. The one township is set out from the Bitter Root Forest Reserve. Though a railroad starting from the Stites terminus of the Clearwater Short Line of the Northern Pacific railroad has been under consideration for some years, the camp is yet with¬out railroad facilities. The projected road would follow the south fork of the Clearwater on easy grades, but would be very expensive to build and maintain. While such a road would greatly benefit those who are now operating in the camp, and in a slight degree stimulate interest in its possibilities, there is hardly business enough to warrant its construction.

Jan 4, 1913

By R. Scot Clark

The reactively sputtered silicon dioxide capacitor -was developed for use in the monolithic integrated circuit, thereby requiring the capacitor to be fabricated on an oxidized silicon slice. The silicon dioxide film is formed by reactively sputtering silicon in a 50 pct Ar-50 pct 0, atmosphere and the physical properties are indistinguishable from silica. A practical upper limit of capacitance per unit area of 0.25 pf per sq mil is reached with the capacitors fabricated from the Si0, film. Methods shown to enhance this value are double stacking the thin-film capacitors and addition of aluminum to the silicon cathode during sputtering to form an aluminosilicate dielectric. A major contribution to the field of diffused integrated circuits would be the addition of auxiliary passive devices for replacement of diffused passive devices which are currently being fabricated for many integrated circuits. This accomplishment would increase the flexibility of the diffusion process in order to concentrate more on transistor parameters rather than on fabricating diffused resistors and capacitors. To pursue this technique, a thin-film SiOz capacitor was developed which has _ proven applicable to many integrated circuits. Although the SiOl capacitor has an application, the major deterrent from extending the integrated circuit into many useful areas such as low-frequency linear application is the low dielectric constant of SiO, and the low usable capacitance in an integrated circuit. This paper will cover the sputtering techniques used for forming the SiO, film, the physical and electrical properties of sputtered SiO,, and yield information concerning the application of these capacitors to integrated circuits. REACTIVE SPUTTERING Reactive sputtering is simply the sputtering of a metal or semiconductor in glow discharge in the presence of a reactive gas. The material to be sputtered is seen in Fig. 1 as the cathode of the system and is bombarded with positively charged ions of the ambient gas. In this investigation, the ambient gas is composed of 50 pct Ar and 50 pct O2 at a pressure of approximately 2.5 X l0-' Torr. The ions are accelerated toward the cathode in the cathode dark space by the electric field and upon striking the cathode effect a momentum energy transfer to the surface atoms. The transferred energy is sufficient to dislodge a surface atom or atoms and these particles diffuse through the glow discharge to the collector or anode. Several mechanisms of oxidation in the reaction chamber can be considered during reactive sputtering. 1) The surface of the cathode is oxidized and the oxide is subsequently sputtered. 2) Oxidation and sputtering occur simultaneously. 3) Sputtering of the cathode material is followed

Jan 1, 1965

By K. Mukherjee

Instantaneous resistance change during martensitic transformation in Fe-30 at. pct Ni alloy has been studied using a low-noise electronic system. The smallest signals recorded in this investigation were of the order of 10 pv. These small signals did not show the initial increase reported by earlier investigators to support a double shear mechanism.&apos; A variety of pulse shapes and sizes was observed during "burst" transformations, and these signals were neither a linear function of the size of martensite plates nor of the volume fraction transformed. Even the smallest signals, presumably from single plates, showed complications resulting from elastic and/or plastic deformation, shock wave propagation, and so forth, which are inherent in the growth process of a martensite plate. The time of formation and interface velocity determined froni this experiment agree very well with the pioneering work of Bunshalz and Mehl.&apos; AN Fe-30 at. pct Ni (c0.005 pct C) alloy was used to study the time of formation of martensite plates. Martensitic transformations, unlike the nucleation and growth processes, are usually characterized by an extremely fast reaction rate. During the transformation, the crystal structure changes and this change is propagated through a finite volume of the parent crystal lattice within a very short time interval. The interface between the two phases probably consists of moving dislocations, and the time of formation of the plate depends on how fast this dislocation interface can move. Knapp and Dehlin~er or Cottrell and Bilby mechanisms, or similar dislocation models, can be used to calculate the time of formation of a martensite plate of a given size. In the past, conventional photographic technique475 as well as electrical resistivity techniques"~-" have been used to measure the time of formation of a martensite plate. The specific resistance of the martensitic phase in Fe-30 at. pct Ni alloy is lower than that of the austenite phase. Therefore if a current is passed through a small austenite sample in series with a large external resistance, then one would observe a voltage change across the sample as martensite is formed. Such dc measurements are shown in Fig. 1. The initial large voltage drop in Fig. 1, at the M, temperature, is due to a "burst" transformation where a large number of plates are formed in a cataclysmic manner within a very short interval of time. Even during the later stages of transformation as shown in Fig. 1, one can observe discontinuous voltage changes due to small bursts. In order to resolve the time scale of such discontinuous stages, the voltage signals are amplified and fed into a highspeed oscilloscope. In this investigation a low-noise amplifier was used for the first stage of amplification. The signal to noise ratio was further improved by the design of a pulse transformer. This transformer was capable of amplifying the signal by a factor of six. Voltage signals were studied over a wide time scale ranging from 2 sec to 0.1 psec. I) EXPERIMENTAL PROCEDURE A) Specimen Preparation. Specimens were cut from induction-melted Fe-30 at. pct Ni (<0.005C) alloy and cold-rolled to 0.2 by 1 mm cross section and an average length of 5 cm. During mechanical shaping, the specimens were strain-annealed at 950°C for 24 hr in vacuum. Finally the finished samples were vacuum-annealed at 1000°C for 6 hr and water-quenched to room temperature. The average grain diameter was 0.02 cm. B) Cooling System. The M, temperature of the alloy was -55°C. Fig. 2 shows the arrangement which was used to cool the specimen at a slow rate. The specimens were mounted inside a i -in.-diam hole in the 2-in.-long section of the copper specimen holder. This cavity was filled with silica gel. A dummy specimen was used under identical conditions for

Jan 1, 1969

By W. B. Potter

There is probably no more interesting group of mineral fuels to be found in any country than that occurring within the limits of the new State of Colorado. The supplies are so abundant, and the occurrence and distribution are so favorable for easy development and transportation to the future manufacturing centres of the State, that they are destined to play a very important part in the material growth and prosperity of the region, the more so because of the rich and varied stores of ores awaiting metallurgical treatment, and the comparative scarcity of timber for fuel. From a purely scientific point, also, these lignitic coals form an interesting and important series. An examination of their geological occurrence and relations opens up new and important questions regarding the comparative value of various kinds of geological evidence, while a study of the character and composition of this class of fuels, which forms a connecting link, as it were, between the lignites and the true bituminous coals, may lead to a more thorough and accurate classification of mineral fuels. The analyses here presented are from samples, of not less than fifty pounds each, obtained by myself during the summer of 1875, and may be regarded as representing very fairly the average run of

By Henry S. Drinker

THE Butler Mine property is situated in the vicinity of Pittston, in the Wyoming coal-field of Pennsylvania. The coal has been worked out from the fourteen-foot or Baltimore vein for a number of years on part of the tract, the old chambers remaining open as when originally abandoned. This vein outcrops on the Butler property, and is nowhere more than sixty feet below the surface of the ground on the line of the cut-off to be described. Above the fourteen-foot vein and about, say midway, between it and the surface of the ground, there is another small vein or rider of coal, about twelve inches in thickness. The rock between the two veins is a carbonaceous slate, about twenty-five feet in thickness. Above the smaller vein is a bed of sandstone, varying in thickness, but generally not less than from eight to ten feet. This sandstone is also carbonaceous, but the proportion of carbon is much less than in the slate below. Both rocks have been analyzed, and before the next Institute meeting, the writer hopes to be able to furnish the exact proportions. The sandstone is overlaid with debris up to the surface of the ground. Some time during the spring of 1876, it was found that the coal left in the worked-out mine had been set on fire, and that the fire was gradually spreading. Inquiry developed the fact that the fire had originally been started by a woman, who had taken up her abode in an old tunnel leading into the workings. Owing to some delay in the early attempts made to extinguish the fire, it finally gained such headway that no ordinary means were found to be effectual. Finally, Mr. C. F. Conrad, civil and mining engineer, of Pittston, Penna., was called in as consulting engineer. He advised the making of a thorough cut through such portion of the old workings as had not been reached by the fire. It was found by survey that this cut could be limited to a length of about one thousand two hundred feet, as the vein faulted on both sides, and that the greatest depth of the cut would be about sixty feet. Subsequently it was decided to tunnel part of the way, thus saving the deepest portion of the cut. In 1856-7, there occurred a fire in the same mine. Two stone-walls in V-shape running from the apex of the V towards the outcrop, were built to cut the fire off, and these walls were carried as far as the vein had at that time been worked. After the walls were finished

Jan 1, 1879

By Henry S. Drinker

The Butler Mine property is situated in the vicinity of Pittston, in the Wyoming coal-field of Pennsylvania. The coal has been &apos; worked out from the fourteen-foot or Baltimore vein for a number of years on part of the tract, the old chambers remaining open as when originally abandoned. This vein outcrops on the Butler prop erty, and is nowhere more than sixty feet below the surface of the ground on the line of the cut-off to be described. Above the four teen-foot vein and about, say midway, between it and the surface of the ground, there is another small vein or rider of coal, about twelve inches in thickness. The rock between the two veins is a carbon aceous slate, about twenty-five feet in thickness. Above the smaller vein is a bed of sandstone, varying in thickness, but generally not less than from eight to ten feet. This sandstone is also carbonaceous, but the proportion of carbon is much less than in the slate below. Both rocks have been analyzed, and before the next Institute meet ing, the writer hopes to be able to furnish the exact proportions. The sandstone is overlaid with debris up to the surface of the ground. Some time during the spring of 1876, it was found that the coal left in the worked-out mine had been set on fire, and that the fire was gradually spreading. Inquiry developed the fact that the fire had originally been started by a woman, who had taken up her abode in an old tunnel leading into the workings. Owing to some delay in the early attempts made to extinguish the fire, it finally gained such headway that no ordinary means were found to be effectual. Finally, Mr. C. F. Conrad, civil and mining engineer, of Pittston, Penna., was called in as consulting engineer. He advised the making of a thorough cut through such portion of the old workings as had not been reached by the fire. It was found by survey that this cut could be limited to a length of about one thousand two hundred feet, as the vein faulted on both sides, and that the greatest depth of the cut would be about sixty feet. Subsequently it was decided to tunnel part of the way, thus saving the deepest portion of the cut. In 1856-7, there occurred a fire in the same mine. Two stone walls in V-shape running from the apex of the V towards the out crop, were built to cot the fire 06 and these walls were carried as far as the vein had at that time been worked. After the walls were finished

Jan 1, 1879

By F. C. Schrader, Alfred H. Brooks

Last fall (1899) we had the good fortune to be able to spend a few weeks in the new placer gold-mining region of Alaska, which is known as the Nome region. Cape Nome, after which the region has been named, and which forms the southeastern corner of the Nome Mining District, is an unimportant promontory on the southern coast of the Seward Peninsula (see map, Fig. 1). The name Seward has recently been given to the great peninsula which forms the northwestern extremity of Alaska. To the north of it is the Arctic ocean, to the south Bering sea, while its wesbernmost extremity, Cape Prince of Wales, is separated from the Asiatic coast by the Bering straits. The coast line of the peninsula is of a cuspate character, consisting of a succession of sandy, crescent-shaped beaches and rocky headlands. The interior has been but little explored; but we know that it is comparatively rugged, the higher mountain peaks rising probably from 4000 to 5000 feet in elevation. The mountains have an easterly and westerly trend, and the water-shed between the two oceans probably nearly bisects the peninsula. At Golofnin bay, the southeastern part of the Seward peninsula, some spruce is found, but to the west the region is entirely timberless, except for a sparse growth of stunted

Jan 1, 1901

By A. Adiassevich

PETROLEUM has been found in Russia in various localities from north to south, as may be seen from the list given below: (a) In the basin of the Petchora river, Northern Russia. (b) In the basin of the Volga river, in the governments of Samara and Saratoff. (c) In the government of Astrakhan and in the Uralsk territory, close to the northern and eastern coast of the Caspian sea. (d) At Grozny in Northeastern Caucasus. (e) In the Daghestan territory, Eastern Caucasus, on the Caspian sea. (f) On the Apsheron peninsula (Baku and other districts) close to the Caspian sea shore. (g) On the island of Tcheleken in the Caspian sea, also on the island of Sviatoi. (h) In the Transcaspian territory on the Neftianaia Gora (Oil hill) and on the surrounding hills. (i) In the Ferghana valley in Russian Central Asia. (j) On the Kertch and Taman peninsulas on the Black sea. (k) In Siberia it has been discovered in the Transbaikal territory and on the island of Sakhalin. In the above-mentioned districts petroleum has been found to exist under different geological conditions and to vary in its chemical and physical properties. At the present time petroleum is produced in Russia at Baku, Grozny, on the island of Tcheleken, in the Ferghana district, and in the Uralsk territory. The yearly production in 1912 throughout the Russian Empire amounted to 69,400,000 barrels, of which the Baku fields were responsible for 52,000,000 barrels. This shows that the Baku fields on the Apsheron peninsula are the chief oil-producing centers in Russia, being at the same time the oldest of all our oil fields.. In this paper I shall discuss the Baku fields only, leaving all the others until a later date.

Jan 5, 1914

By AIME AIME

THE ninth International Petroleum Exposition held at Tulsa, May 16-23, broke all size, sales, and attendance records of previous shows. More than $12,500,000 worth of equipment was on the grounds. There were 546 companies exhibiting and every available inch of the fifteen acres allotted to exhibit was taken. Drake Drive, the main street of the exposition, was literally "supply row" with National Supply, Frick-Reid, Continental Supply, Oil Well, Bridgeport, International Derrick and Equipment, and Parkersburg Rig and Reel companies occupying the entire space. The exhibitors were a cross section of American industry, with such firms, besides the strictly oil equipment firms, as the United States Steel Corp. and others allied to the oil industry, exhibiting. Between $10,000,000 and $15,000,000 of equipment is estimated to have been sold on the grounds during the exposition. Valuable contacts were made by the exhibitors with key oil men. Attendance passed the 175,000 mark for paid admissions in contrast with 154,000 for the eighth exposition in 1934. Visitors registered from Venezuela, Soviet Russia, India, Germany, Spain, Mexico, England, Canada, France, Colombia, Greece, West Indies, and Rumania. Hotels were overflowed and a housing bureau found rooms in private homes for thousands. Oil companies set up a schedule of shifts in order that as many of their field men might attend as possible. It is said that the companies want a two-weeks&apos; show in 1938 so that more time will be avail-

Jan 1, 1936

By Thomas H. Sheehan

The purpose of this paper is to present an application of computer technology to assist the mineral company financial executive in assessing exchange risks. The paper is divided into five parts: Background, Translation Approaches, Theory, Empirical Validation, and Conclusion. BACKGROUND Exchange risk results from a change in the rate of exchange between a host and a home country&apos;s currencies. Legitimate reasons exist for changes in the currency exchange rates among countries in a world with over a hundred different currencies. These reasons include: different economic growth rates, social factors, cultural heritages, and political motivations. The problem of exchange rate changes are perennial and exist whether the world operates on exchange rates or floating exchange rate practices. The cause of the problem is trade and international payment imbalances. If one accepts the premise that exchange rates fluctuate over time, then the mineral company financial executive faces a continual process of reassessment of the impact of exchange rate changes on the financial worth of his company. (1) The mineral company financial executive prepares balance sheets and income statements that are audited by certified public account- ants annually for shareholders, bankers, and tax authorities. The financial executive translates assets and equities denominated in foreign currencies into domestic dollars, e.g., Japanese firms convert to Yen, French firms convert to Francs, and so on. When figures from foreign subsidiary operations are consolidated into the balance sheets of the parent corporation, estimates of the company&apos;s finan-

Jan 1, 1977

By H. J. Denning, M. W. Brabbins, A. K. Isaac

The quality of a coalface floor is the essential element that enables powered supports to generate their designed loads in control of coalface strata. The paper introduces a technique for the appraisal of coalface foundation stability. A criterion of support efficiency, viz., the support pressure increase/strata convergence, is included in case study data obtained from investigations in the South Wales Coalfield, U.K.

Jan 1, 1984

By R. W. Diamond

Three mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd.: (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the St. Eugene Concentrator, Moyie, B. C., and (3) the Tadanac (Customs) Concentrator, Trail, B. C. Differential flotation is the only concentration method employed in all three plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals —lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential flotation.

Jan 1, 1928

By Stanley J. LeFond, Neal Davis

Drilling an oil well or most other types of drilling or coring is no longer a simple and uncomplicated operation. Drilling today at depths which exceed 9144 m (30,000 ft) is hazardous and requires personnel with long and varied experience in drilling. It also requires extensive experience and knowledge in the use of materials which are added to the drilling fluid or "mud," more often than not materials utilizing an industrial mineral. The drilling fluid can vary from a simple mixture of water and "mud" to a very sophisticated, scientifically compounded drilling fluid. Industrial Minerals Used in Drilling Fluids Industrial minerals which are commonly used in oilwell drilling and completion are listed in Table 1. The most important minerals, determined by sales, are bentonite and barite. The other minerals listed are either used to achieve a specific purpose or are used regularly but in limited quantities. The main suppliers of drilling fluids internationally are Magcobar Div., Dresser Industries, Inc.; Baroid Div., National Lead Co.; IMC Drilling Mud Co., (a subsidiary of international Minerals and Chemicals Corp. and Halliburton Co.); and Milchem, a division of Baker Industries. Most of the industrial minerals are found in North America, with barite mines and processing plants located in Nevada, Arkansas, Missouri, and Arizona, and bentonite mines near Graybull, WY. Other mines, such as those in Nova Scotia, are capable of shipping to South America and to the European and Middle East countries. Most of the materials processed by any of the suppliers must conform to specifications set by the American Petroleum Institute (API) or the Oil Companies Material Organization (OCMA). These specifications provide for uniform physical and chemical properties of the materials to be sold on the open market. Function of Drilling Fluids In the early days of rotary drilling, the primary function of drilling fluids was to bring the cuttings from the bottom of the hole to the surface. Today it is recognized the drilling fluid has at least ten important functions: 1) To remove the cuttings from the bottom of the hole and carry them to the surface. 2) To cool and lubricate the drill string and drill bit. 3) To build an impermeable cake on the wall of the hole. 4) To control subsurface pressures. 5) To hold cuttings and weight material in suspension when circulation is interrupted. 6) To release sand and cuttings at the surface. 7) To support part of the weight of drill pipe and casing. 8) To reduce to a minimum any adverse effects upon the formation adjacent to the hole. 9) To insure maximum information about the formation penetrated. 10) To transmit hydraulic horsepower to the bit. In order to accomplish some or all of these functions while penetrating formations of various characteristics, several types of drilling fluids systems have been designed. Types of Drilling Muds There are two basic drilling fluid systems-water-base muds and oil-base muds. There is a wide variety of groups within these two main

Jan 1, 1983

By R. W. Diamond

THREE mills are now operated by the Consolidated Mining & Smelting Co. of Canada, Ltd. : (1) The Sullivan Concentrator, Chapman Camp, B. C. (near Kimberley, B. C.), (2) the St. Eugene Concentrator, Moyie, B. C., and (3) the Tadanac (Customs) Concentrator, Trail, B. C. Differential flotation is the only concentration method employed in all three I plants. Tables are used for pilot work only. Values in all ores treated are as minerals of some or all of the metals -lead, zinc, gold or silver. Occasional customs ores contain small amounts of copper. Sulfide iron content of ores treated varies from a [ ] low figure in some ores to 38 per cent. iron in Sullivan ore. Gangue minerals vary considerably. A few customs ores are somewhat oxidized and as a result present difficulties. Flotation equipment and control are similar in the three mills, and the flow sheets at the St. Eugene and Tadanac mills, while much simpler, are modeled after that of the Sullivan Concentrator. In this paper I will not detail treatment nor equipment in any of our plants but will describe special features in, or in connection with, all of them. I will then deal with flotation reagents, describing our use of each of them, particularly where differing from general practice. I will conclude with comments on special subjects related to differential flotation.

Jan 1, 1928

By M. G. Cheney

The purpose of this paper is to review the more important developments in the production of petroleum during 1930 in Texas, excluding the Panhandle and Gulf Coast districts, giving emphasis to trends rather than to statistics. Outstanding Developments Aside from increasing curtailment of drilling operations and general prorating of production by state authority the most noteworthy developments for the year appear to have been: 1. Demonstrations of the fictitiousness of potentials as shown first by Darst Creek pool, rated at 180,000 bbl. and having actually 78,000 bbl. daily, and especially by the Hendricks pool of Winkler County, with potential of about 1,000,000 bbl. daily in mid-year and production of only 52,000 bbl. daily when opened to continuous full production in December. 2. Rapid development of the Darst Creek pool under competitive drilling. 3. Orderly and highly successful development of the Van pool under unit operation. 4. Failure of several highly rated structures southwest and northeast of Van. 5. Extension of the deep Simpson production at Big Lake and increased interest in these pre-Mississippian pays in North Central Texas and West Texas. 6. Discovery of prolific wells in northwest Rusk County from sands of Upper Cretaceous age, portending a rapid and extensive development campaign around the northwest margin of the Sabine uplift. North Central Texas It appears logical to discuss the new developments by districts as set out by the American Petroleum Institute, but North Texas and West Central Texas districts will be treated together. Pre-Mississippian,.—The pre-Mississippian beds, which in previous years yielded a few large wells in Young, Cooke and Callahan counties,

Jan 1, 1931