Search Documents

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of' 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 ' and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

FREDERICK LAIST, * Anaconda, Mont. (written discussion?).-All who are interested in the treatment of oxidized copper ores by leaching have been awaiting the publication of this paper, which comes up to our expectations in all respects. Messrs. Tobelmann and Potter are to he congratulated upon the excellent way in which they have set forth the workings of the process as applied at Ajo. Numerous attempts have been made to apply the electrolytic copper process but all have failed, except the installation of the Chile Copper Co., at Chuquicamata. Some of these failures were due to insufficient financial backing and inadequate ore reserves, which necessitated opera-

Jan 5, 1919

By F. N. Speller

ASIDE from the Tuesday symposium on gases in metals, the Iron and Steel Division swung into action for the first time on the third day of the meeting with a discussion of iron and steel alloys. Dr. E. S. Davenport opened the discussion on Wednesday morning by presenting the paper written by himself in association with E. C. Bain and W. S. N. wiring on the equilibrium diagram of iron-manganese-carbon alloys. A written discussion by Mr. Scott showed qualitative agree- ment, but some quantitative disagreement. Messrs. Marsh and Sisco discussed the paper at length, pointing out non- agreement of certain conclusions with the phase rule. Dr. Krivobok, although differing with the authors on some points, stated that in his opinion the information collected would be valuable in the practical use of these alloys.

Jan 1, 1932

By G. D. Van, Arsdale

IT IS particularly appropriate that a paper on this subject should be presented in Spanish, before a Spanish speaking audience, and in a South American country, first because of the facts that these countries today have not only the largest copper leaching plant in existence but also present great opportunities for future extension of hydrometallurgy; and second, because of the fact that the first copper made by any wet method was doubtless produced before existing records at the Rio Tinto deposits in present day Spain.

Jan 1, 1925

By Thomas Leonard Watson

I. HISTORICAL. BARITE has been mined for many years in various parts of Virginia, probably the earliest mining-operations being in Prince William county, within 600 ft. of the Fauquier county line, about 4 miles south of east from Catlett, a station on the Southern Railway. It is claimed that the mineral was mined here as early as 1845. Mining-operations in Campbell and Pittsylvania counties in the Piedmont region, and near Marion in Smyth county, in the southwest Virginia Valley region, were begun about 30 years ago. The mining and milling of barite on a commercial scale in Tazewell and Russell counties are more recent, and commenced about 15 years ago. II. GEOGRAPHICAL AND GEOLOGICAL DISTRIBUTION. Barite occurs in many counties in the State, as shown in Fig. 1, but the industry has been confined to only a few of them. Its occurrence is noted in two of the three major divisions of the State-namely, the Piedmont region east of the Blue Ridge, and the Paleozoic area west of the Blue Ridge. In the Piedmont region the mineral has been mined in the following counties:, Bedford, Campbell, Louisa, Prince William, and Pittsylvania. In the region west of the Blue Ridge, composed of Paleozoic sediments, barite has been mined in Montgomery, Russell, Smyth, and Tazewell counties. Of the counties mentioned, Bedford, Campbell, and Pittsylvania of the Piedmont region, and Russell, Smyth, and Tazewell of the Valley region, have been the principal producers. In 1906, operations were confined to five counties-Bedford, Louisa, Pittsylvania, Russell, and Tazewell-but in the first two counties named there was no production, the work being solely development.

Jan 9, 1907

By W. A. Thomas

STEAM is, and doubtless always will be, the basic power in the anthracite industry, either directly applied through engines and pumps or electrically. The rapidity with which electric power is being applied to the mining and preparation of anthracite leaves little doubt as to its utility and economy. There is practically no operation, except possibly the drilling of hard rock, that has not been successfully electrified and the matter of drilling is handled economically with electrically driven compressors and the standard compressed-air drills. Conservation and the seemingly ever-increasing cost of production, justify careful consideration of the possible results of the more extensive use of electric power in the industry. It is not planned to discuss, herein, the relative economies of individual applications but to consider the relative economy and flexibility of steam and electric power. The reports available for the year 1920 indicate a production of slightly over 80,000,000 tons of anthracite, of which 8,843,500 tons were used for power and heating purposes; in other words, over 11 per cent. of the production was used at the mines. Some of this was used to generate electric power at the mines, about 160,000,000 kw-hr., while 150,000,000 kw.-hr. was purchased from the public utility companies. One large producer, who is buying some electric power and generating some, used over 13 per cent. of the production for power and heating at the mines. Another producer, where considerable electric power is generated on the properties, is using less than 9 per cent. of the output for power and heating. One of the largest producers has a fuel consumption of over 15 per cent. of the output, besides which considerable power is purchased. A careful study of the field indicates that steam-operated plants use upwards of 13 per cent. of the production for power and heating, while electrically operated plants use about 1 per cent. for heating; so that, for steam-power purposes at least 12 per cent., or 268.8 lb., are used for power out of each ton produced.

Jan 9, 1921

By W. J. Taylor

SOME eight years ago I became interested to a considerable extent in one of the well-known deposits of sulphury iron ore in New Jersey, and, as a consequence, soon became interested in the subject of the elimination of the sulphur. On investigation I found that no department of pig-iron manufacture had received less attention than that of roasting or calcining ores for the elimination of sulphur, carbonic acid, water, etc. My first devices to eliminate sulphur were naturally in the lime-kiln line, with solid fuel mixed with the ore, in the same way as common lime is burnt with small coal. While this process will succeed tolerably well for carbonates or calcareous ores, even though they contain sulphur as sulphates, I soon found it would not answer for our magnetites, which are very hard and dense, carrying from 2 to 5 per cent. of sulphur as pyrites, and become very sticky as soon as any attempt is made to roast them at a high heat. Some laboratory experiments developed the fact that the nearer the gaseous current surrounding the hot ore approached in composition pure atmospheric air the more rapidly the sulphur was oxidized, while in an atmosphere composed largely of carbonic oxide, carbonic acid, and nitrogen, it seemed almost impossible to reduce the sulphur more than one-half, which was a confirmation of the well-known fact that just one-half of the sulphur in pyrites volatilizes very easily, and that the trouble is mainly to remove the remainder. It was thus apparent that the atmosphere surrounding the ore was of as much importance as the temperature. This led to the trial of a kiln to heat the ore by conduction through the brick. It was divided into ore-chambers, which were surrounded with flues, through which the products of combustion of gaseous fuel passed without coming in contact with the ore. We did not, however, succeed by this arrangement in getting more than a cherry-red heat, which, of course, was too low to accomplish anything. I had at this point become convinced – 1st. That gaseous fuel only would accomplish the work successfully. 2d. That since a high temperature was required to insure a rapid oxidation of the sulphur, and also to make the ore open and porous,

Jan 1, 1881

By AIME AIME

THE PAPER, "Surface Effects on Assay Beads Caused by Metals of the. Platinum Group," presented by J. L. Byers, before the Institute of. Metals Division at the February meeting of the Institute, is the subject of interesting discussion, an abstract of which follows. The original paper is available at Institute headquarters as a Preprint. Member-What assurance have you that the percentage of metals, as stated, is really an accumulation?

Jan 1, 1932

United Engineering Trustees, Inc C E Reistle, Jr (to Oct '55), A B Kinzel, '56, Andrew Fletcher, '57, Philip Kraft (from Oct '55 to '59) The Engineering Foundation W M Peirce, '56, A M Gaudin, '58 Engineering Societies Library Board Frank T Sisco, '58, C H Behre, Jr Engineering Societies Personnel Service Board of Directors E J Kennedy, Jr, E H Robie Advisory Committee, Milwaukee F T Agthe Special Survey Committee C M Cooley American Standards Association Mining Standards Board E R Borcherdt, '55, Otto Herres, '55, J K Richardson, '56, E W Bullard, '56, Alternate

Jan 1, 1955

By William G. [Peryam], Bishop Ottey M., Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rock-surfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to P8.00 per ton, and from the property to San Fernando the rate is P16.00 per ton. The company pays the road toll, P1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydro-separation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement.† About 3130 tons of limestone, 620 tons 0f clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5,800,000 bbl, of cement. Following are some of the cement requirements of the Shasta Dam specifications: [PERCENT Chemical composition: Loss in ignition2.25 Insoluble residue0.75 SO32.25 MgO5.00 Uncombined lime in clinker (CaO)1 .25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 3,5 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O7)Not more than 7 Tetracalcium aluminoferrite (4CaO.A12O3.Fe203) Not more than 0 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength-in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1941

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By A. M. Kivari

Operations at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hy-droseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the mallufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. † About 3I30 tons of limestone, 620 tons of clay and I00 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. up to the present time, the ccrporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modihed-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Red- ding, Calif., the total demand being 5,800,000 bbl. of cement. Following are some of the cement require ments of the Shasta Dam specifications: Per Cent Chemical composition: Loss in ignition.......... 2.25 Insoluble residue......... 0.75 SO3.................... 2.25 MgO................... 5.'' Uncombined lime in clinker (CaO)......... I.25 Percentage of iron oxide to alumina ratio....... I.5 Compound composition: Tricalcium silicate (3CaO.SiO2)........... Not more than 35 Dicalcium silicate (zCaO.SiO2)........... Not less than 40 and not more than 65 Tricalcium aluminate (3CaO.Al2O3).......... Not more than 7 Tetracalcium aluminofcr- rite (4CaO.Al²O³.Fe²O³) Not more than 20 Fineness: The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following:

Jan 1, 1942

By B. B. Wood, M. J. Rzasa, E. W. Hough

An apparatus for the determination of fluid-fluid interfacial tension by the pendant drop method has been constructed. The apparatus is refined beyond those previously described in that the samples are introduced into an evacuated windowed cell without contacting air or mercury. Interfacial tension data are reported for the water-methane system between 74 and 280°F and 15 and 15,000 psi. The variation of wettability of the stainless-steel dropper tip with pressure and temperature was observed incidentally to the measurements. INTRODUCTION The most refined previous apparatus --for the determination of fluid-fluid interfacial tension at reservoir conditions was built by Hauser and Michaels.' These authors used the pendant drop method, previously investigated by Andreas, Hauser, and Tucker.' Recently, Fordham3 has made the pendant drop method an absolute one by numerical integration of the differential equation of drop shape. It is necessary to know the difference in density of the two fluids and the acceleration due to gravity in order to evaluate the interfacial tension from measurements of drop dimensions. Contact angle is not involved in the measurements by this method. Some precise tests of the method have been made at atmospheric pressure and 77°F by Douglas," who found agreement with established values to within about 0.1 per cent for water and air, cyclohexane and air, benzene and air, and benzene and water. No values of interfacial tension from the recent pendant drop apparatusJ have been published by Hauser and Michaels. However, values for the water-benzene and water-decane systems are given in Michaels' thesis5 or Dressures from 15 .to 10,000 psi and temperatures from 73 to 268ºF. Some determinations on gas-oil and gas-water systems in the range of 15 to 4,000 psi and 78 to 178°F have been made by Hozott,' by the drop-volume method. The capillary rise method has been used to investigate the interfacial tension in gas-oil systems at 88°F to several thousand psi by Swartz.7 Other determinations in gas-oil systems at pressures under 1,000 psia have been made by Jones: and Beecher and Parkhurst.9 The scarcity of data for pressures above 5.000 psi is apparent. APPARATUS An assembly drawing of the working section of the interfacial tenqion apparatus is given in Fig. 2. 'The endanant drop (A) is housed in a pressure chamber having glass windows (B). An agitator (6) is provided. The metal parts of the apparatus coming into contact with the sample are made of AISI: Type 316 steel. Drain grooves are provided around the whdows so that the sample in contact with the O-rings is not returned to the working section when the pressure is reduced. A schematic arrangement of the apparatus is given in Fig. 3. The working section containing the pendant drop (A) is filled by samples from bombs (B) with the aid of the vacuum system (C). The O-ring sealed pistons (D) used to separate the sample from the hydraulic fluid are shown together with the pressure production and measurement system (E). A front view of the apparatus is shown in Fig. 1. Most of the hydraulic system is at the top of the panel. The pump and displacement piston are at the lower right. The Variacs for the air bath heaters. the camera. and the vacuum gauge are a1so visible on the panel. The working section together with a window closure and a drop-forming tip closure are shown in Fig. 9. The carbon arc light source with filter is visible in the upper part of the picture. Two sides of the air bath with the impeller and a part of the convection shield can also be seen. The assembled air bath is shown in Fig. 10.

Jan 1, 1951

By E. W. Hough, B. B. Wood, M. J. Rzasa

An apparatus for the determination of fluid-fluid interfacial tension by the pendant drop method has been constructed. The apparatus is refined beyond those previously described in that the samples are introduced into an evacuated windowed cell without contacting air or mercury. Interfacial tension data are reported for the water-methane system between 74 and 280°F and 15 and 15,000 psi. The variation of wettability of the stainless-steel dropper tip with pressure and temperature was observed incidentally to the measurements. INTRODUCTION The most refined previous apparatus --for the determination of fluid-fluid interfacial tension at reservoir conditions was built by Hauser and Michaels.' These authors used the pendant drop method, previously investigated by Andreas, Hauser, and Tucker.' Recently, Fordham3 has made the pendant drop method an absolute one by numerical integration of the differential equation of drop shape. It is necessary to know the difference in density of the two fluids and the acceleration due to gravity in order to evaluate the interfacial tension from measurements of drop dimensions. Contact angle is not involved in the measurements by this method. Some precise tests of the method have been made at atmospheric pressure and 77°F by Douglas," who found agreement with established values to within about 0.1 per cent for water and air, cyclohexane and air, benzene and air, and benzene and water. No values of interfacial tension from the recent pendant drop apparatusJ have been published by Hauser and Michaels. However, values for the water-benzene and water-decane systems are given in Michaels' thesis5 or Dressures from 15 .to 10,000 psi and temperatures from 73 to 268ºF. Some determinations on gas-oil and gas-water systems in the range of 15 to 4,000 psi and 78 to 178°F have been made by Hozott,' by the drop-volume method. The capillary rise method has been used to investigate the interfacial tension in gas-oil systems at 88°F to several thousand psi by Swartz.7 Other determinations in gas-oil systems at pressures under 1,000 psia have been made by Jones: and Beecher and Parkhurst.9 The scarcity of data for pressures above 5.000 psi is apparent. APPARATUS An assembly drawing of the working section of the interfacial tenqion apparatus is given in Fig. 2. 'The endanant drop (A) is housed in a pressure chamber having glass windows (B). An agitator (6) is provided. The metal parts of the apparatus coming into contact with the sample are made of AISI: Type 316 steel. Drain grooves are provided around the whdows so that the sample in contact with the O-rings is not returned to the working section when the pressure is reduced. A schematic arrangement of the apparatus is given in Fig. 3. The working section containing the pendant drop (A) is filled by samples from bombs (B) with the aid of the vacuum system (C). The O-ring sealed pistons (D) used to separate the sample from the hydraulic fluid are shown together with the pressure production and measurement system (E). A front view of the apparatus is shown in Fig. 1. Most of the hydraulic system is at the top of the panel. The pump and displacement piston are at the lower right. The Variacs for the air bath heaters. the camera. and the vacuum gauge are a1so visible on the panel. The working section together with a window closure and a drop-forming tip closure are shown in Fig. 9. The carbon arc light source with filter is visible in the upper part of the picture. Two sides of the air bath with the impeller and a part of the convection shield can also be seen. The assembled air bath is shown in Fig. 10.

Jan 1, 1951

By J. A. Stachura

Continuous mining machinery provides the coal industry with one way to compete for a larger share of the total energy market. Various types of machines are discussed and some of the problems with continuous miners, encountered by operators, are reviewed. Equipment manufacturers are working with mine personnel to provide solutions for problems that arise. While coal production over the past 25 or 30 years has been on a horizontal plane, coal's share of the total energy market has declined. To participate more effectively in this total energy market, it is necessary to produce coal more efficiently. It is the obligation of all management, employes, and mining departments to gear the deep mining industry to the rapid progress and changing of today's modern industry. This can be accomplished in the near future with the selection of the proper type of continuous miner best suited to each operator's individual situation. In most mining operations there is tremendous incentive to undertake the continuous mining program. It can reduce the size of the mine greatly by permitting a minimum of working places; it makes pillar recovery work more efficient from the standpoint of overall cost, amount of coal recovered, and safety. The work force can be reduced materially permitting closer and more efficient supervision. It simplifies maintenance because equipment can be more readily standardized. The trend of the coal market favors the use of continuous mining machines. Although there appears to be a general feeling that continuous mining is still a relatively new program and will be slow in replacing conventional mechanical equipment, the fact is that tremendous strides have been made since the first machines were installed in 1948. This program is advancing at approximately the same rate that mobile loading machines replaced hand loading. From 1948 to 1955 there were approximately 450 continuous mining machines in service. In October 1959, a survey revealed that there were more than 700 continuous mining machines in service. Many operators have expressed a desire to undertake this program, but they feel that they could not do so at this time because of one or more of the following reasons: 1) the thickness of their coal seams, 2) seam characteristics, 3) soft bottoms, 4) bad roof conditions, 5) size consist, 6) insufficient flexibility in machines, 7) difficult ventilation problems, and 8) high maintenance costs. With the realization on coal about the same today as it was in 1948, or slightly less and since coal is still failing to participate to a greater degree in the total energy market, it is not surprising that the coal industry is desperately exploring more economical methods for deep mining. The manufacturers are aware that the coal industry is willing to invest in continuous miners if the equipment is built for maximum flexibility, will produce higher tons per man, and assure long life between overhaul programs. CONTINUOUS MINING MACHINES Before discussing details regarding the selection of a continuous miner, let us have a preview of some of the continuous mining machines which are available to the coal industry today. Jeffrey Manufacturing Co.: The machine shown is the Jeffrey 76 A.M. Colmol. This is their most widely used miner, and has been particularly successful in central Pennsylvania and in high-wall mining in western Kentucky. One of the outstanding features of this auger-type miner is its portability. The entire mining range can be changed from its lowest point to the maximum height without stopping the mining operation. Jeffrey 76 B.M. Colmol: This machine is similar to the 76 A.M. model; however, it is built bigger and stronger for a mining range of 50 1/2 to 72 in. This is the model that is now available (Fig. 2). Jeffrey has added two arms to the top row, omitted the odd arm in the bottom row, thus permitting a 50 pct larger throat opening. This eliminates one

Jan 1, 1961

By M. J. McPherson

Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air down-stream from the water eliminator, as shown in [Fig. 1]. The duct configuration can be designed to create good mixing at the outlet.

Jan 1, 1984

By R. R. Sayers

SILICOSIS is a term known to almost everyone today. Yet, in spite of a great deal of study, much is still to be learned regarding the disease. Government organizations are still continuing their investigations, begun near Joplin, Mo., 25 years ago. Work is also being done in several universities, as Harvard, Pennsylvania, Rochester, and Toronto, and at least two private organizations, the Air Hygiene Foundation of America, Inc., and the Saranac Laboratories for the Study of Tuberculosis, devote most of their time to this subject. Similar studies have been and are being made in many other countries.

Jan 1, 1939

By A. U. Seybolt, C. H. Mathewson

As is well known, many questions affecting the properties and uses of a metal cannot be answered without careful consideration of the state of purity realized in the various operations of preparation, refining, or special treatment that have brought the product to its final state. The occurrence of an impurity in minute quantity offers no guarantee that its effect will be inconsiderable because dissolved substances often modify the properties of a metal quite out of proportion to their concentration. In such cases the determination of solid solubility must be accepted as a problem of considerable difficulty, requiring the use of especially purified materials and methods not ordinarily used in the metallurgical laboratory. This aspect of the equilibrium between metals and their oxides is especially important and a search for fundamental data reveals little except conflicting opinion even concerning the systems of common occurrence and interest. Rhines and Mathewson1 in 1934 studied the solubility of oxygen in solid copper by annealing to equilibrium in air and gave reasons for the failure of other methods, notably the ordinary procedure of heat-treatment followed by microscopic examination, to yield reliable results. In this paper, a similar study has been made of the solubility of oxygen in cobalt. The simple theory of this method is outlined below.

Jan 1, 1935

By Arthur M. Miller

FROM the time of its establishment in 1933, the Tennessee Valley Authority has been active in the field of phosphates. Under the T.V.A. Act it has a broad Congressional mandate to guide a unified development of the resources of the region for the long-range benefit of the people. As one phase of this function, it is directed to co-operate with farmers in the experimental large-scale use of improved fertilizers and development of better fertilizer practices. Following careful study, it was concluded that the objectives of this phase could best be attained by soil rebuilding through the use of phosphatic fertilizer and lime in an improved farm management sys- tem. This activity was launched through a program of test and demonstration on farms and simultaneous technical investigations to develop new and improved phosphatic fertilizers. Phosphorus has since become a keystone of the Authority's resource development and conservation program. Human effort is being conserved by phosphate utilization on the farm, and mineral conservation has been promoted by technical developments in phosphate mining and manufacturing operations.

Jan 1, 1944